Professional Documents
Culture Documents
Skirt Data : Skirt Outside Diameter at Base Skirt Thickness Skirt Internal Corrosion Allowance Skirt External Corrosion Allowance Skirt Material SOD STHK SCA 8072.0000 25.0000 0.0000 0.0000 SA-516 70 mm. mm. mm. mm.
Basering Input:
Thickness of Basering Design Temperature of the Basering Basering Matl Basering Operating All. Stress Basering Yield Stress Inside Diameter of Basering
TBA
50.0000 80.00
mm. C
SA-516 70 [Normalized] BASOPE 162.00 242.90 DI DOU 7960.0000 8468.0000 N./mm N./mm mm. mm.
Nominal Diameter of Bolts Bolt Corrosion Allowance Bolt Material Bolt Operating Allowable Stress Number of Bolts Diameter of Bolt Circle Bolt Allowable Shear Stress
BND BCA
mm. mm.
SA RN DC
N./mm
mm. N./mm
Thickness of Gusset Plates Width of Gussets at Top Plate Width of Gussets at Base Plate Gusset Plate Elastic Modulus
PV Elite 2013 SP2 Licensee: NATCO AL-RUSHAID MIDDLE EAST LTD. FileName : J49-D-0011A_B------------------------------------Basering Calculations : Step: 17 10:49p Dec 10,2013
Gusset Plate Yield Stress Height of Gussets Distance between Gussets Dist. from Bolt Center to Gusset (Rg/2) Number of Gussets per bolt SY HG RG CG NG 242.9 407.0000 250.0000 125.0000 2 N./mm mm. mm. mm.
Thickness of Top Plate or Ring Radial Width of the Top Plate Anchor Bolt Hole Dia. in Top Plate
CA
1.2000
mm.
Dead Weight of Vessel Operating Weight of Vessel Earthquake Moment on Basering Wind Moment on Basering Percent Bolt Preload
Use AISC A5.2 Increase in Fc and Bolt Stress Use Allowable Weld Stress per AISC J2.5
No No
Fact
1.0000
515848.6
Kg-m.
PV Elite 2013 SP2 Licensee: NATCO AL-RUSHAID MIDDLE EAST LTD. FileName : J49-D-0011A_B------------------------------------Basering Calculations : Step: 17 10:49p Dec 10,2013
W = TW M = Test Moment
= (( 4 * M/DC ) - W ) / RN per Jawad & Farr, Eq. 12.3 = (( 4 * 0/8276.000 ) - 0 )/36 = 0.0000 Kgf [** No Uplift ** ]
Required Area for Each Bolt, Based on Max Load Area Available in a Single Bolt (Corr) Area Available in all the Bolts (Corr) Bolt Stress Based on Simplified Analysis Allowable Bolt Stress 158.6 [Fact]
cm cm cm N./mm N./mm
Shear Stress in a Single Bolt [taub]: = Shear Force / ( 2 * Bolt Area * Number of Bolts ) = 7397554/( 2 * 29.08 * 36 ) = 346.5 N./mm. Must be less than 622.0 N./mm .
Concrete Contact Area of Base Ring Concrete Contact Section Modulus of Base Ring
CCA
65544.81 0.1307E+11
cm mm.
Concrete Load (Simplified method), Wind in Operating Condition [Sc]: = ((ppl/100*(Abt*Sa)+W)/Cca) + M/CZ per Jawad & Farr Eq. 12.1 = (0.000 (1046.8365 *158 +612211 )/65544.81 ) + 732441/.13068E+11 = 1.47 N./mm
20.68
N./mm
Determine Maximum Bending Width of Basering Section [Rw1,Rw2]: Rw1 = (Dou - SkirtOD)/2, Rw2 = ( SkirtID - Di + 2*Sca )/2
PV Elite 2013 SP2 Licensee: NATCO AL-RUSHAID MIDDLE EAST LTD. FileName : J49-D-0011A_B------------------------------------Basering Calculations : Step: 17 10:49p Dec 10,2013
Rw1 = 198.000 , Rw2 = 31.000 mm.
Calculation of required Basering Thickness, (Simplified) [Tb]: Allowable Bending Stress 1.5 Basope = 243.000 N./mm = Max(Rw1,Rw2) * ( 3 * Sc / S ) + CA per Jawad & Farr Eq. 12.12 = Max(197.9999 ,31.0000 ) * ( 3 * 1.466/243.000 ) + 1.2000 = 27.8338 mm.
Basering Stress at given Thickness [Sb] = 3 * Sc * ( Max[Rw1, Rw2]/(Tb - Ca) ) = 3 * 1.466 * ( Max[198.000 , 31.000 ]/(50.000 - 1.200 ) ) = 72.383 , must be less than 243.000 N./mm
Required Thickness of Top Plate in Tension: (Calculated as a fixed beam per Megyesy) Ft = (Sa*Abss), Rm = (Ft * 2 * Cg)/8, Sb Wt = (Topwth Bolt Allowable Stress * Area Bending Moment Allowable Bending Stress Bnd), Width of Section
Required Thickness of Continuous Top Ring per Moss: a P l = ( Dc-SkirtOD )/2 = Sa*Abss = Avgwdt Skirt Distance to Bolt Circle Bolt Allowable Stress * Area Average Gusset Width Constant Term f( b/l )
g1 = Gamma 1
PV Elite 2013 SP2 Licensee: NATCO AL-RUSHAID MIDDLE EAST LTD. FileName : J49-D-0011A_B------------------------------------Basering Calculations : Step: 17 10:49p Dec 10,2013
g2 = Gamma 2 g = Flat distance / 2 Constant Term f( b/l ) Nut 1/2 Dimension (from Tema) Allowable Bending Stress
Fb =
Required Thickness of Gusset in Compression, per AISC E2-1: 1. Allowed Compression at Given Thickness: Factor Kl/r Per E2-1 Factor Cc Per E2-1 Allowable Buckling Str. per E2-1 Actual Buckling Str. at Given Thickness 28.1973 127.4726 135.54 23.29 N./mm N./mm
14.8202
mm.
2. Allowed Compression at Calculated Thickness: Factor Kl/r Per E2-1 Factor Cc Per E2-1 Allowable Buckling Str. per E2-1 Act. Buckling Str. at Calculated Thickness 103.5128 127.4726 85.50 85.51 N./mm N./mm
Summary of Basering Thickness Calculations: Required Basering Thickness (simplified) Actual Basering Thickness as entered by user 27.8338 50.0000 mm. mm.
Required Top Ring/Plate Thickness as a Fixed Beam Required Thickness of Continuous Top Ring (Moss)
54.3437 41.3874
mm. mm.
PV Elite 2013 SP2 Licensee: NATCO AL-RUSHAID MIDDLE EAST LTD. FileName : J49-D-0011A_B------------------------------------Basering Calculations : Step: 17 10:49p Dec 10,2013
Actual Top Ring Thickness as entered by user 65.0000 mm.
14.8202 50.0000
mm. mm.
Compute the Weld load at the Skirt/Base Junction [W] = SkirtStress * ( SkirtThickness - CA ) = 3.991 * ( 25.000 - 0.000 ) = 10.17 Kgf/mm.
Results for Computed Minimum Basering Weld Size [BWeld] = W / [( 0.4 * Yield ) * 2 * 0.707] = 10/[( 0.4 * 242 ) * 2 * 0.707] = 0.726 mm.
Results for Computed Minimum Gusset and Top Plate to Skirt Weld Size
Vertical Plate Load [Wv] = Bolt Load / ( Cmwth + 2 * ( Hg + Tta ) ) = 47027.4/( 350.000 + 2 * ( 407.000 + 65.000 ) ) = 36.343 Kgf/mm.
Horizontal Plate Load [Wh] = Bolt Load * e / ( Cmwth * (Hg+Tta) + 0.6667 * (Hg+Tta) ) = 47027.4 * 102.000/(350.000 * (472.000 ) + 0.6667 * (472.000 ) ) = 15.290 Kgf/mm.
PV Elite 2013 SP2 Licensee: NATCO AL-RUSHAID MIDDLE EAST LTD. FileName : J49-D-0011A_B------------------------------------Basering Calculations : Step: 17 10:49p Dec 10,2013
= ( Wv + Wh) = ( 36.34 + 15.29) = 39.428 Kgf/mm.
Results for Computed Min Gusset and Top Plate to Skirt Weld Size [GsWeld] = Wr / [( 0.4 * Yield ) * 2 * 0.707] = 39.43/[( 0.4 * 242 ) * 2 * 0.707] = 2.814 mm.
Weld Load [Wv] = Bolt Load / ( 2 * TopWth ) = 47027.4/( 2 * 198.000 ) = 118.756 Kgf/mm.
Weld Load [Wh] = Bolt Load * e / ( 2 * Hgt * TopWth ) = 47027.4 * 102.00/( 2 * 472.000 * 198.000 ) = 25.663 Kgf/mm.
Results for Computed Min Gusset to Top Plate Weld Size [GtpWeld] = Wr / [( 0.4 * Yield ) * 2 * 0.707] = 121.50/[( 0.4 * 242 ) * 2 * 0.707] = 8.673 mm.
PV Elite 2013 SP2 Licensee: NATCO AL-RUSHAID MIDDLE EAST LTD. FileName : J49-D-0011A_B------------------------------------Basering Calculations : Step: 17 10:49p Dec 10,2013
Note: The calculated weld sizes need not exceed the component thickness framing into the weld. At the same time, the weld must meet a minimum size specification which is 3/16 in. (4.76 mm) or 1/4 in. (6.35 mm), depending on the component thickness.
Summary of Required Weld Sizes: Required Basering to Skirt Double Fillet Weld Size Required Gusset to Skirt Double Fillet Weld Size Required Top Plate to Skirt Weld Size Required Gusset to Top Plate Double Fillet Weld Size 6.3500 6.3500 8.6728 8.6728 mm. mm. mm. mm.