Professional Documents
Culture Documents
Structure
8.1 8.2 8.3 Introduction
Objectives
Strain Energy
8.4 8.5
8.6
Castiglianos Theorem
8.6.1 8.6.2 8.6.3 Application of Castiglianos Theorem to Angular Movements Application to Truss Problems Application to Beam Problems
8.7 8.8
8.1 INTRODUCTION
This unit introduces you to the concept of strain energy, how it is related to stress and strain and the method of estimating this energy in different modes of application of forces or loads on the body. It also explains to you how to obtain the stresses in the case of sudden and impact loads using the strain energy concept. Further, it deals with Castiglianos theorem which can be employed to estimate the defections of deformable bodies under loads.
Objectives
After studying this unit, you should be able to conceptualise the potential energy, estimate the strain energy under different types of loads, obtain the stresses in a body when subjected to suddenly applied or impact loads, and determine the deflections of beams through the application of Castiglianos theorem.
129
converted to an equivalent kinetic energy if the body is allowed to fall from the height by developing velocity of fall. Let us now consider the case of a deformable body subjected to certain external forces or what we call as loads. Because of the property of deformability of the body, each of the points of application of these forces may undergo certain displacement. Thus, the force moves through a certain distance, which is equivalent to doing work on the body, i.e. a certain energy imparted to the body. One may now ask a question, where did all this energy go? because it had to be conserved. This question, we shall answer in the next section.
U =
1 P 2
Load, P
Extension,
Figure 8.1
The strain energy per unit volumes is after referred to as resilience. The resilience at the yield point or proof stress is termed as proof resilience. The strain energy stored upto the fracture of the material is generally known as toughness. In the earlier units, it is seen that loads may be applied on a body in different modes, viz., as axial loads, as shear loads, as bending loads or as torsional loads. In the following sections, we shall derive expressions for the strain energy stored under each of the above forms of loading.
tension and contract if P is compression) by an amount where the P relationship is a shown in Figure 8.1.
Cross-sectional Area A
Strain Energy
P L
Figure 8.2
The work done by the force P is equal to the strain energy stored in the bar. Thus,
U=
1 P 2
U =
Stress P L L= E A E
1 PL P 2 L P = 2 AE 2 AE
P If we rewrite the above expression in terms of the stress and the strain in the bar, A
U =
ds
Figure 8.3
131
Strain energy, dU, of the element = work done = But, shear strain, =
dU =
1 1 Q = Q ds 2 2
1 Q Q 2 ds Q ds = 2 2GA GA
U =
Q 2 ds Q 2 L = 2 AG 2 AG
M dx dx
R d
Figure 8.4
= = =
=
1 M d 2 ds 1 (since, ds = R d ) M 2 R 1 M M E M ds since, = 2 EI I R
M 2 ds 2 EI
L 0
M 2 ds 2 EI
M 2 dx 2 EI
Strain Energy
where dx is the undeformed element length. If M is constant throughout the length L, then
U = M2 L 2 EI
ds
d T
Figure 8.5
1 T d 2 T d T ds or d = =G J ds GJ
Where J is the polar moment of inertia and G is the shear modulus of the material. Therefore, total strain energy resulting from torsion, U =
T2 L . 2 GJ
T 2 ds 2 GJ
Determine the diameter of an aluninium shaft which is designed to store the same amount of strain energy per unit volume as a 50 mm diameter steel shaft of the same length. Both shafts are subjected to equal compressive axial loads. What will be the ratio of the stresses set up in the two shafts? Take Esteel = Es = 201 GN/m2 and Ealuminium = Ea = 67 GN/m2. Solution Since the strain energy per unit volume of the two shafts is equal, we get
2 2 2 Ea 67 1 a = s or a = = = 2 2 Ea 2 Es Es 201 3 s
s = 3 a or
s = 3 a
133
Thus,
P P = 3 2 2 Ds Da 4 4
4 Da 4 Ds
i.e. or
=3
4 Da = 3 (50) 4
Da = (3 (50)4 ) 4 = 65.8 mm
Two shafts are of the same material, length and weight. One is solid and of 100 mm diameter, the outer is hollow. If the hollow shaft is to be store 25% more energy than the solid shaft when transmitting torque, what must be its internal and external diameters? Assume the same maximum shear stress in both the shafts.
Solution
Let A be the solid shaft of diameter Da and B be the hollow shaft with external diameter Db and internal diameter db. Since both the shafts are to be the same material and of equal weight, their volumes should be equal. Therefore, or
2 2 2 Db ( Db db ) L= L 4 4
2 2 2 Da = Db db = (100) 2 mm 2
Since the maximum shear stress is the same for both the shafts, we have,
a = b
Ta Db J a = Tb Da J b
But it is also given that the strain energy of B = 1.25 strain energy of A. Thus,
Then,
2 Db =
4 4 2 2 2 2 db ) 4 ( Db + db ) ( Db db ) 4 ( Db = 4 2 5 5 Da Da
or 134
2 Db =
4 4 4 2 2 2 ) because Db ( Db + db db = Da = 104 5
or
2 Db =
4 2 2 ( Db + Db 102 ) 5
Strain Energy
Therefore,
Thus, the internal and external diameters of the hollow tube are 57.74 mm and 115.47 mm, respectively.
SAQ 1
(a) Calculate the strain energy stored in a bar of circular cross-section of diameter and length of 0.2 m and 2 m, respectively, when it is (i) (ii) (iii) subjected to a tensile load of 25 kN, subjected to a torque of 25 kN m, and subjected to a uniform bending moment of 25 kN m.
Take E = 208 GN/m2, G = 80 GN/m2 for the bar material. (b) Compare the strain energies of two bars of the same material and length and carrying the same gradually applied compressive load if one is 25 mm diameter throughout and the other is turned to 20 mm diameter over half its length, the remainder being 25 mm diameter. If both bars are subjected to pure torsion only, compare the torsional strain energies stored if the shear stress in both bars is limited to 75 N/mm2. (c) A 50 mm square alloy-steel bar 1 m long is a part of a machine and must resist an axial load of 100 N m. What must be the proportional limit of the steel to safely resist the energy load elastically with a factor of safety of 4? E = 200 GPa.
P P
1
Extension
Figure 8.6
135
Since the bar is strained to the same extent in both the cases, the strain energy should be the same for the two cases. However, strain energy is equal to the work done by the load. or
W = W
1 P P = P or P = 2 2
This means that the suddenly applied load which is required to produce a certain value of instantaneous strain is half the equivalent value of static load (gradually applied load) required to produce the same strain. Vice-versa, one can say that the effect of a suddenly applied load is two times that achieved when the load is applied gradually. Thus, greater care must be exercised while designing structural elements that are susceptible to sudden loading conditions.
Load, W L h
Rigid Collar
Figure 8.7
The rod is suspended from a rigid support. When the load is dropped it will produce a maximum instantaneous extension in the bar, at the point of impact. Then, the load would have done work equal to W (h + ). This then must be equal to the strain energy stored in the bar. If is the instantaneous stress produced in the bar. The strain energy, U =
2 AL 2E 2 AL 2E
W ( h + ) =
L 2E
Therefore,
L 2 AL W h + = E 2E
Strain Energy
or Denoting
2W 2WEh =0 A L
2W as st , which would have been the stress in the bar if W were to have been A applied gradually, the above equation can be written as 2 2 st 2 Eh st = 0 L
L E
If the load is not dropped but suddenly applied from effectively zero height (h = 0 in the above equation), the stress developed would be
= 2 st
It is a result which we have already predicted in the earlier section. Thus, it can be seen that the stresses resulting from impact loads will be even higher and any design work where impact loading is possible should always employ a safety factor well in excess of two.
SAQ 2
An axial pull of 50 kN is suddenly applied to a steel rod 2 m long and 1000 mm2 in cross-section. Calculate the strain energy that can be absorbed, if E = 200 GPa.
Figure 8.8
137
Then, the strain energy, U = Work done by W = W (h + ) where is the instantaneous maximum deflection under the load W. If We is an equivalent static load which, when applied gradually, produces the same deflection as the impact load W, the work done by We will be equal to the work done by W. i.e.
1 We = W ( h + ) 2
Let st be the deflection of the beam if W were applied gradually. Then, by the linear relationship of load to deflection, it can be written
W We = or We = W st st
Substituting this in the above work equation, we get
W = W ( h + ) 2 st
On simplifying, we get
2 2 st 2 st h = 0
2 = st st
1+
2h st
2h = st 1 1 + st
This then will be the instantaneous deflection under the impact load W. Once is known one can obtain We and the maximum bending moment, Mmax produced in the beam by the application of We. Then, the maximum stress max occurring in the beam can be obtained from the bending equation as
max =
M max C , I
where I is the moment of inertia for the cross-section and C is the extreme fibre distance from the neutral axis.
SAQ 3
(a) A bar 3 m long and 5 cm diameter hangs vertically and has a collar securely attached at the lower end. Find the maximum stress induced when, (i) (ii) (b) a weight 2.5 kN falls from a height of 12 cm on the collar, and a weight of 25 kN falls from a height of 1 cm on the collar.
An unknown weight falls through 10 mm onto a collar rigidly attached to the lower end of a vertical bar 3 m long and 600 mm2 in section. If the maximum instantaneous extension is known to be 2 mm, what is the corresponding stress and the value of the unknown weight. Take E = 200 kN/mm2.
138
Example 8.3
Strain Energy
What will be the instantaneous stress and elongation of a 25 mm diameter bar, 2.6 m long, suspended vertically, if a mass of 10 kg falls through a height of 300 mm onto a collar which is rigidly attached to the bottom end of the bar? Take E = 200 GPa.
Solution
2 EhA 1 + 1 + LW
We have
W A
Thus, the maximums tress and elongation are 96.24 MPa and 1.25 mm, respectively. This elongation of 1.25 mm is very small compared to the height of fall namely 300 mm. Let us find out the stress if this elongation were to be neglected in the calculation. When it is neglected the work strain energy equation becomes.
Wh = 2 AL 2E
or
2WhE = AL
= 96.04 MPa
This shows that the error in the stress calculation is insignificant even if the elongation is neglected.
Example 8.4
When a concentrated force of 1 kN is applied at the midspan point of a simply supported beam a static deflection of 5 mm is produced. The same load produces a maximum stress of 158 MN/m2. Determine the magnitude of the instantaneous stress produced when a weight of 10 kg is allowed to fall through a height of 12 mm onto the beam at midspan. What will be the instantaneous deflection?
Solution
Let We be the equivalent gradually applied load which produces the same static deflection max as that of the impact load. Then,
Now, equating the work done by the impact load to that done by the equivalent static load, we get
We max = W (h + max ) 2
i.e.
139
Hence,
We =
max =
It is given that the load of 1 kN produces a maximum stress of 158 MN/m2. Therefore, a load of We should produce a maximum stress, max equal to (158 We) MN/m2.
max = 158 0.791 = 124.978 MN/m 2 ; 125 MN/m 2
Thus, the maximum stress and maximum deflection are 125 MN/m2 and 4 mm, respectively.
SAQ 4
(a) When a load of 20 kN is gradually applied at a certain point on a beam, it produces a deflection of 13 mm and a maximum bending stress of 75 MN/m2. From what height can a load of 5 kN fall onto the beam at this point if the maximum bending stress is to be 150 MN/m2. A beam uniform cross-section with centroid at mid-depth and length 7 m, is simply supported at its ends and carries a point load of 5 kN at 3 m from one end. If the maximum bending stress is not to exceed 90 MN /m2 and the beam is 150 mm deep, (i) (ii) working from the first principles, find the deflection under the load, and what load dropped from a height of 75 mm onto the beam at 3 m from one end would produce a stress of 150 MN/m2 at the point of application of the load?
(b)
m =
U Pm
where m is the displacement of the point of application of the load Pi in the direction of Pm. 140
Let us prove the theorem now. Consider the beam in Figure 8.9 with forces PA, PB, PC, etc. acting at points A, B, C, etc.
B
Strain Energy
PA (+ PA) A
PB
PC
B C
Figure 8.9
Let A, B, C, etc. be the deflections in the direction of loads at the points A, B, C, . . ., respectively.
B
Then, the strain energy of the system is equal to the work done.
U =
1 1 1 PA A + PB B + PC C + . . . 2 2 2
If one of the loads PA is now increased by an amount PA, the changes in the deflection will be A, B, C, etc. as shown in Figure 8.9. In increasing the load from PA to (PA + PA), extra work is done and it is as follows (refer Figure 8.10 also).
B
= PA A +
1 PB B + PB B + PC C + . . . 2
This should be equal to the increase in strain energy U. Neglecting the product of small quantities ( PA A) since they are very small as compared to the other terms.
U = PA A + PB B + PC C + . . .
Load At A Load At B
PA Extra Work = PB + B
A + A
Deflection at A
B + B
Deflection at B
Figure 8.10
141
Let us now consider the case where we apply the loads (PA + PA), PB, PC, etc. gradually to the full value. As the final loads in the case are exactly the same as the earlier case and as all the loads are applied statically, the final deflections should also be the same.
B
Then, the strain energy in the case, U (neglecting product of small terms PA A) would be as follows :
U = =
1 1 1 ( PA + PA ) ( A + A ) + PB ( B + B ) + PC (C + C ) + . . . 2 2 2 1 1 1 1 1 PA A + PA A + PA A + PB B + PB B 2 2 2 2 2 + 1 1 PC C + PC C + . . . 2 2
1 1 1 1 1 PA A + PB B + PC C + . . . + PA A + PB B 2 2 2 2 2 + 1 1 PC C + . . . + PA A 2 2
=U +
1 1 1 1 PA A + PB B + PC C + . . . + PA A 2 2 2 2
However, since loads as well as deflections are the same in both the cases, the total strain energy should also be the same. Hence,
U = U + U
or
U =
1 1 1 1 PA A + PB B + PC C + . . . + PA A 2 2 2 2
2 U = PA A + PB B + PC C + . . . + PA A U = PA A + PB B + PC C + . . .
U = PA A or
In the limit, A =
U = A PA
U PA U U = B , = C , etc. PB PC
U = M . PM
As a simple example of the application of Castiglianos theorem, let us consider a bar of cross-sectional area A and length L under axial tension P. From earlier section we have known that the strain energy U in this case is given as
U = P2 L 2 AE
U PL = P AE
which we recognise as the extension of the bar under the load P, i.e. the displacement of the point of application of the load P. 142
Strain Energy
Fi 2 Li 2 Ai E
where E is the Youngs modulus of the material. Then, the total strain energy stored in the truss can be written as follows :
U =
i =1
Fi 2 Li 2 Ai E
Now, as per Castiglianos theorem the deflection n under the load Pn in its direction will be n =
m F L F U m Fi 2 Li = = i i i Pn Pn i = 1 2 Ai E i = 1 Ai E Pn
Fi is the rate at which Fi varies with Pn with all other loads remaining constant or in Pn other words it is the force in the member when a unit load is applied instead of Pn, while all other loads are zero.
The above concept can still be applied to find the deflection in any direction at any joint of the truss even when no load is acting in that direction or at that point. In this case, we introduce a fictitious force Q at the pint in the direction in which we need the deflection. Then we determine the member forces for the load system which now includes Q also. Then,
U =
Q =
i =1
Fi 2 Li 2 Ai E
Therefore,
m F L F U i = i i Q i = 1 Ai E Q
However, in actual problem there is no Q or its value is zero. So we put Q = 0 in the above expression and obtain Q. The concept of unit load can be brought in even here. Now when we include Q in the load system Fi can be written as Fi = FiP + FiQ (principle of superposition) 143
where FiP and FiQ are the member forces only due to the Ps and Q, respectively. Then, U = ( FiP + FiQ )2 Li 2 Ai Ei
m
and
Q =
m
( FiP + FiQ ) Li Ai E
i =1
( FiP + FiQ ) Q
=
Q =
m
( FiP + FiQ ) Li Ai E
( FiP + FiQ ) Ai E
i =1
FiQ F iP + Q Q
FiQ Q
i =1
Li
FiP = 0 ). Q
FiQ Q
is nothing but the member force due to a unit load in the direction of Q at the point Q of application of Q while all other loads are zero.
Example 8.5
FiQ
In the truss shown in Figure 8.11, the cross-sectional area of its top and bottom chords is equal to 2.4 103 mm2, while the cross-sectional area of its diagonal and vertical members is equal to 1.6 103 mm2. The modulus of elasticity of the material form which the members are made is E = 200 GPa. Compute the vertical and horizontal components of the deflection at joint 7.
Solution Vertical Deflection at Joint 7
Since there is a 40 kN acting vertically at joint 7, this is a case of straight forward application of Castiglianos theorem. As a first step, the forces in the members of the truss (F) are determined under the action of the two 40 KN loads that are acting on the truss. These FL forces are shown in column 2 of Table 8.1. Then, the respective are AE calculated. These are presented in column 3.
2 9 4 10 6 6 5 1 1 3 40 k N 3 @ 2.4 m = 7.2 m 2 5 7 3 7 40 k N
8 3.2 k N
Figure 8.11
144
Table 8.1
Membe r 1 2 3 4 5 6 7 8 9 10 F* (kN) 60 60 30 100 40 50 40 50 120 30 A (102 mm2) 2.4 2.4 2.4 1.6 1.6 1.6 1.6 1.6 2.4 2.4 L (mm) 2400 2400 2400 4000 3200 4000 3200 4000 2400 2400
Strain Energy
FL AE
0.30 0.30 0.15 1.25 0.40 0.625 0.40 0.625 0.60 0.15
F P
1.5 1.5 0.75 1.25 0 1.25 1.00 1.25 2.25 0.75
FL AE
F P
0.450 0.450 0.1125 1.5625 0.0000 0.78125 0.400 0.78125 1.350 0.1125 + 6.000** mm
FL F 7 = AE P (vertical)
* Sign convention : ve compression and + ve tension.
** Positive sign indicates that the deflection is in the direction of the load. i.e. downwards.
Next, all the external loads are replaced by a single unit load acting vertically down at joint 7 and the member forces are obtained. The result F will be equal to . These values are presented in column 6 of the P Table 8.1. Then, the rest of the calculations are completed to obtain FL F . which according to Castiglianos theorem will be equal to the AE P vertical deflection at joint 7. We can see this deflection is 6 mm downwards.
Horizontal Deflection at Joint 7
In this case, there is no horizontal load at joint 7. So to apply Castiglianos theorem, we have to first introduce a fictitious horizontal load Q at joint 7, then find the members forces and differentiate these forces with respect to FL F . Q. Finally, is determined. Then, Q unit is made equal to zero in AE Q this expression to get 7 (horizontal). However, here we use the unit load concept and solve this problem. But you are advised to check the result by the above procedure. Here also, the first step is to determine the member forces (F) under the external load system. Thus, column 2 of the table remains the same. Now the external load system is replaced by a single horizontal unit load (because we require horizontal deflection). Let us assume that this unit load acts left to right. Now, the member forces are determined again under the action of F this unit load alone. The result will be equivalent to Q Q = 1 at 7. These values are shown in column 6 of Table 8.2.
FL F Now the horizontal deflection at joint 7 is given by . . The results AE Q are presented in Table 8.2. From this table, it can be seen that horizontal deflection of joint 7 is 0.75 mm towards the left.
Table 8.2
145
Membe r 1 2 3 4 5 6 7 8 9 10
A (102 mm2) 2.4 2.4 2.4 1.6 1.6 1.6 1.6 1.6 2.4 2.4
L (mm) 2400 2400 2400 4000 3200 4000 3200 4000 2400 2400
FL AE
0.30 0.30 0.15 1.25 0.40 0.625 0.40 0.625 0.60 0.15
F Q
FL AE
F Q
1 1 1 0 0 0 0 0 0 0
0.30 0.30 0.15 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.75* mm
FL F 7 = AE Q (horizontal)
* Negative sign indicates that the deflection is opposite to the direction of unit load.
SAQ 5
Determine the vertical and horizontal deflection of point A in the pin-joined frame shown in Figure 8.12. All members have EA = 20 MN. Given is AB = AC = BC = 1 m and DB = 0.5 m.
B
A C
50 kN
Figure 8.12
U =
0
M 2 ds M 2 dx = 2 EI 2 EI 0
The bending moment will be a function of the loads. Then, by Castiglianos theorem the deflection under one of the loads, P, in its direction will be
U = P P
M 2 dx = 2 EI
M M dx . EI P
146
If we have to find the deflection at a point where there is no load, a fictitious load Q has to be introduced at that point in the direction in which the deflection is needed and U is U computed. Then, is computed. If in this expression Q is made equal to zero, the Q result will be the deflection at the pint of application of Q.
Strain Energy
U =
M 2 dx 2 EI
U = = Q Q = 0 Q
M 2 dx 2 EI
Q=0
L M M = . dx 0 EI Q Q = 0
M will Q be the moment at a section due to a unit load at the point of application of Q with no other loads present on the beam. We shall now apply these concepts to some practical problems.
From the similarities with the truss problems, it can easily be recognised that
Example 8.6
Determine the vertical deflection at the tip of the cantilever shown in Figure 8.13.
P
E, I
Figure 8.13
Solution
Measuring the distance x from the free end, the bending moment at any section distant x from the tip is given as M = Px Then,
U =
M 2 ds = 2 EI
P2 x2 P 2 L3 dx = 2 EI 6 EI
The positive sign shows that the deflection is in the direction of P, i.e. downwards. U can be written as follows : It may be seen that P
Px ( x) dx EI M Px M = and x = EI EI P
147
where
Example 8.7
Determine the deflection (vertical) at a distance a from the tip in Example 8.6.
Solution
Since in this case there is no load at the point where the deflection is needed, we introduce a fictitious load Q as shown in Figure 8.14.
Q P
a L
Figure 8.14
Then,
M = Px and
M = 0 for 0 x a Q M = ( x a) for a x L Q
and
L
M = Px Q ( x a) and M M dx = EI Q =
a
Px (0) dx + EI
[ Q ( x a ) Px] [ ( x a)] dx EI
Px ( x a) + Q ( x a) 2 dx EI
L M M . dx a = = EI Q 0 Q = 0 P = EI
Example 8.8
Px ( x a) dx EI
2 L ( x a ) x 2 a
x 2 P L3 a3 L2 a dx = + EI 2 2 6 3
Determine the slope of the cantilever given in Example 8.6 at its free end.
Solution
To determine rotation in a beam we should have a couple acting at that point. Since at the free end, there is no couple, we introduce a fictitious couple M as shown in Figure 8.15.
P
M A
A
L
Figure 8.15
148
Now
M = Px M and
M = 1 M
Strain Energy
L M M L ( Px + M ) 1 . dx A = = EI M EI 0 M = 0 0 M = 0
PL2 2 EI
A =
Thus, we see that the tip slope of a cantilever loaded with a concentrated vertical PL2 . force P at its free end is 2 EI
SAQ 6
(a) Using Castiglianos theorem, determine the deflection at the centre of the beam loaded as shown in Figure 8.16. The EI is constant.
W Per Unit Length
L/2
L/2
Figure 8.16
(b)
A steel rod, of flexural rigidity EI, forms a cantilever ABC lying in a vertical plane as shown in Figure 8.17. A horizontal load P acts at C. Calculate (i) (ii) (iii) the horizontal deflection of C, the vertical deflection of C, and the slope at B.
B a C
Figure 8.17
149
8.7 SUMMARY
In this unit, we have (a) (b) (c) (d) (e) (f) (g) (h) introduced the concept of potential energy, introduced the concept of strain energy, shown the relationship between flexural work and strain energy, derived the expressions for strain energy in different modes of loading, seen the differences between gradually applied loads, suddenly applied loads and impact loads, derived the expressions for instantaneous stresses and deflection for axial and bending impact loads, stated and proved Castiglianos theorem, and applied Castiglianos theorems to determine the deflections in trusses and beams.
50 kN m
SAQ 3
(a) (b)
SAQ 4
(a) (b)
SAQ 5
78 mm 24 mm, 1.45 kN
(a) (b)
5WL4 786 EI
Pa 2 Pab 2 Pab ( a + 3b), , 3EI 2 EI EI
150
FURTHER READING
Prasad, Jainti, Strength of Materials, CBS Publishers and Distributors. Timoshenko, Stephan, Strength of Materials Part I and II, CBS Publishing and Distributors. Schaums Outline Series, (1989), Strength of Materials, Second Edition, McGraw-Hill Book Company. Popov, E. P., (1993), Mechanics of Materials, Second Edition, Prentice-Hall of India Private Limited. Ryder, G. H., (1993), Strength of Materials, Educational Low Priced Books Scheme. Case, John, Chilver, L., Ross, Carl, T. F., (1993), Strength of Materials and Structures, Third Edition, Educational Low Priced Books Scheme.
Strain Energy
151
152