Professional Documents
Culture Documents
Operating Manual
January 2005
Index
Technical characteristics ................................................................page Accessories and options ................................................................page Command and connections Lay-Out ............................................page Command and connections description .......................................page Batteries charging informations ....................................................page 2 4 5 6 9
Automatic measurements description ..........................................page 10 Example for Field Application - Noise / Level measurement on single frequency ............................page 11 - Noise / Level RMS measurement on wide band ...........................page 11 - Near Cross-talk measurement on single frequency .......................page 12 - Near Cross-talk measurement on wide band..................................page 12 - Return Loss measurement on single frequency..............................page 13 - Return Loss measurement on wide band........................................page 13 - Attenuation of the line on single frequency .....................................page 14 - Longitudinal Balance measurement on single frequency................page 14 - Longitudinal Balance measurement on wide band .........................page 15 LT2000 Field Applications table .....................................................page 16 Table of parameters and limits of measurements ........................page 17 ATEN LT2000 Line Tester Page 1 / 18
TECHNICAL CHARACTERISTICS
GENERAL
Case.................................. : ABS. Connections ...................... : input "RX" : triple banana jack (a-b-Gnd). input/output "TRX : triple banana jack (a-b-Gnd). polarized connector for supply & battery charger. RJ45-4 connector for headset interface. Display .............................. : 4 lines x 16 characters alphanumeric LCD. Keypad .............................. : microswitches under polyester membrane film. Power supply .................... NiMH internal rechargeable batteries (green type), approx. 4 hours of operating time; external: 11 to 32 Vdc / 1,5 0,6 A. Ambient temperature ........ : operating: 0 50 C; storage: -10 60 C. Freq. accuracy / stability ... : factory accuracy: 2 ppm @ 23 C; temperature deviation: 10 ppm 0 to 50 C; long term stability: 5 ppm / year. Dimensions ....................... : 100 x 40 x 210 mm. Weight............................... : < 1 Kg.
SIGNAL GENERATOR Output Impedance ............ : < 10, 150 (120 or 135 on request), 600 balanced ( 5F series); Output frequency range .... : from 200 Hz up to 2000 kHz. Resolution ......................... : 1 Hz from 200 Hz to 10 kHz; 100 Hz from 10 kHz to 2000 kHz. Output Level...................... : 0.0 dBm 0.2 dB @ 10 kHz. Output Level accuracy vs. frequency (referred to 10 kHz):
-2 -1 dB 600 120150 200 Hz -1 -0.5 dB -0.5 -0.2 dB 0.1 dB 0.3 dB 200 Hz 800 Hz 800 kHz 2000 kHz 300 Hz 600 Hz 2 kHz 800 kHz 2000 kHz
Page 2 / 18
SELECTIVE LEVEL METER Input impedance ............... : 150 (120 or 135 on request) 600 , 200 k balanced ( 5F series); Tunable frequencies ......... : tracking with TX Freq. (200 Hz 2000 kHz). Selectivity (fo 800 Hz) .... : -0.5 dB @ 30 Hz fo; -50 dB @ 500 Hz fo. Level measurements ........ : absolute (dBm) and relative (dBr). Input range........................ : -100 +5 dBm; Resolution: 0.1 dB. Noise floor (TX off)............ : -100 dBm @ 600 ; -95 dBm @ 120150 . Intrinsic cross-talk ............. : -90 dB @ 1000 kHz. Level meas. accuracy ....... : 0.2 dB @ 0.0 dBm - 10 kHz. Level meas. accuracy vs. input level (Referred to 10 kHz): - - - - TX OFF - - - -
0.3 dB 600 +5 dBm 120150 +5 dBm 0.2 dB 0.5 dB 0 dBm -70 dBm 0 dBm -70 dBm 1 dB -85 dBm -80 dBm 2 dB -95 dBm -90 dBm -100 dBm -95 dBm
(Referred to 10 kHz / 0 dBm): -1 -0.5 dB -0.5 -0.2 dB 0.1 dB 0.3 dB 200 Hz 800 Hz 800 kHz 2000 kHz 600 Hz 2 kHz 800 kHz 2000 kHz
Hybrid circuit - return loss . : 40 dB with nominal load. Image / spurious rejection. : -60 dB (fo 800 Hz).
AUTOMATIC MEASUREMENTS IN SCAN MODE Noise (or Level): - frequency & level readout of min. and max. noise level; - frequency band and RMS noise level readout; Return-loss: frequency & level readout of min. and max. echo level; Near Cross-talk: frequency & level readout of min. and max. cross level; Programmable bands (1 step/sec. speed) base band from 200 Hz min. to 10 kHz max. (100; 200; 400; 1000 Hz selectable step) high band from 10 kHz min. to 2000 kHz max. (0.1; 0.2; 0.4; 1; 2; 4; 10 and 20 kHz select. step)
SWEEP GENERATOR MODE Sweep generator base band from 200 Hz min. to 10 kHz max. (10 step/sec. speed) (100; 200; 400; 1000 Hz selectable step); high band from 10 kHz min. to 2000 kHz max. (0.1; 0.2; 0.4; 1; 2; 4; 10 and 20 kHz select. step). ATEN LT2000 Line Tester Page 3 / 18
OPTIONAL ACCESSORIES
LT02 -Headset
LT05 -Fixed Balanced Attenuator: LT06 -Balance Meas.Adapter LT07 150 (120 or 135) or 600 3 , 6 , 10 , 20 , 30 or 40 dB 150 (120 or 135 on Resistive Termination 150 (120 or 135 on request) or 600 . request) and 600 .
All information contained in this document are subject to change without notice ATEN LT2000 Line Tester Page 4 / 18
14 15
8 9 10 11 12
1 2 3 4 5 6 7
13
Page 5 / 18
4) REL Pressing this key, the last measure is frozen and subsequently
subtracted from the next measures and the dBm indication changes to dBr. Pressing the key again, the absolute value in dBm is restored.
5) RUN Key for starting, reading values and getting out from the automatic
measurement pre-selected by the FUN key (11). At the first pressure of the key the automatic measurement starts. At the end of the automatic measurement the display shows Done and the frequency and the level of the stronger measured signal is immediately shown; further pressures on the key call back on the display: - frequency and level of the poorer measured signal; - for Noise measurement only, pressing again, the evaluated RMS level of Noise on pre-selected band-width is shown too; ATEN LT2000 Line Tester Page 6 / 18
6)