Professional Documents
Culture Documents
SLAB TYPES
Slab type B 08 Width; b (mm) Specific weight (t/m) * 860 1.510 B 09 940 1.656 B 10 1 045 1.860 B 11 1 120 2.000 B 12 1 220 2.178 B 13 1 305 2.341 B 14 1 420 2.585 B 15 1 550 2.820
1. MAIN PARAMETERS
Coil Sheet
1.218.0 8001 540 8001 540 8001 500 1 7508 000 1 75012 000
1.212.5 with mill edge with trimmed edge up to the thickness of max 8 mm above the thickness of 8 mm
applied within the thickness range of 2.08.0 mm for plain sheets in strength grades IV. and for sheets with pattern in strength grades IIV.
1 000
1 250
h = 2.5; 3; 4; 5; 6; 8; 10; 12 mm
h = 2.5; 3; 4; 5; 6; 8; 10; 12 mm
1 500
2. PRODUCT GROUPS
The latest issued standard are applied for our products. The mechanical properties and chemical compositions in the tables are valid taking into account the supplementary specifications of the indicated standards. Definition of strength grades: According to EN 10051: Grade A with minimum yield strength Re 300 MPa Grade B with minimum yield strength 300 MPa < Re 360 MPa Grade C with minimum yield strength 360 MPa < Re 420 MPa Grade D with minimum yield strength 420 MPa < Re 900 MPa ISD Dunaferr Co. Ltd. applies DASZ 03 instead of EN 10051: I. Steel grades characterised with maximum yield strength, used for cold rolling, II. Steel grades with minimum 185 MPa yield strength, III. Steel grades with minimum 235 MPa yield strength, IV. Steel grades with minimum 275 MPa yield strength, V. Steel grades with minimum 340 MPa yield strength, VI. Steel grades with minimum 420 MPa yield strength, VII. Steel grades with minimum 460 MPa yield strength, VIII. Steel grades with minimum 500 MPa yield strength. DASZ 03 standard includes the producible dimension ranges as well as dimensional tolerances by strength grades. These tolerances are either the same as or stricter than that specified by EN 10051 standard. Tolerances of hot rolled products according to DASZ 03 standard are chapter 5. In case of standards with the same number, but from different years the specifications of the standard included in the delivery contract are normative.
2.1. HOT ROLLED MILD STEEL STRIPS 2.1.1. Steels for cold rolling
Typical applications: re-rolling, pressing base material, small and medium scale deep-drawing and production of parts suitable for special deep-drawing and complex machining.
Strength grade DIN 1614 St 22 I. RR St 23 St 24 JIS G 3131 SPHC SPHD SPHE ASTM A568 SAE 1010 1008 1006
Steels with increased yield strength for cold rolling are included in chapter 2.6.3.
The products are delivered in normalised or rolled condition. If the product is ordered with normalising rolling the +N marking shall be added to the grade specification. Symbols of the impact test specification
V-notch on 1010 mm specimen 27 J JR J0 J2 J3 J4 J5 J6 40 J KR K0 K2 K3 K4 K5 K6 60 J LR L0 L2 L3 L4 L5 L6 Test temperature (C) 20 0 -20 -30 -40 -50 -60
Letters: GH, H L B P S SL N
for high temperature service, with hot yield point test for low temperature service base material of gas bottles base material of pressure vessels and boiler plates cold toughness, applicable also at low temperature cold toughness, with specification of impact test value at -50C produced by normalising rolling
N B
Letters according to EN 10025-3 standard: N by normalising rolling NL by normalising rolling, impact test at -50 C
Letters according to EN 10149-2 standard: M by thermo-mechanical rolling C suitable for edge bending
3. SPECIAL PRODUCTS
3.1. HOT ROLLED COILS AND SHEETS FOR PLASMA AND LASER CUTTING
The requirements of suitability for laser cutting are summarised in DASZ 216 standard. These products are ultra high-purity steels with low inclusion content, produced according to reduced chemical composition limit values, with reduced S-, P- and Si-contents; fine-grained, micro-alloyed, with more reduced mechanical values than those specified by similar standards and low internal stress, suitable for edge bending, as well as for plasma and laser cutting. Steel grades, specified by DASZ 216 standard or any other national or international standards, suitable for plasma and laser cutting, can be ordered. Flatness In case of ordering plain sheets the flatness tolerances, depending on the strength grades according to EN 10051 standard, are given in the following table. Definition of the strength grades (A, B, C, D) according to EN 10051 standard are included in chapter 2 of this catalogue.
Flatness tolerance max. (mm/m) A 4 B 4 C 5 D 5
In case of ordering coils suitable for laser cutting our company guarantee the flatness tolerances in the above table for cut-to-length sheets only after performance of a professional levelling process on a cutting line with suitable technical conditions.
Diamond pattern
Teardrop pattern
Pattern Diamond Top width (mm)) Bottom width (mm) Length (mm) 2.814.20 4.204.90 Teardrop 3.907.10 6.308.30 27.3033.60 Dense teardrop 4.908.45 8.2010.10 24.3029.30 Wide teardrop 3.847.22 8.009.30 30.0032.00
Pattern height:
Thickness; h (mm) 1.602.30 2.313.00 3.019.99 10.0016.50* Minimal pattern height (mm) 0.60 0.80 1.00 0.80 * above 12 mm thickness it can only be ordered in coils 2.00 Maximal pattern height (mm)
4. SURFACE
Our products are delivered according to EN 10163-2 standard class B sub-class 3.
1.201.29 1.301.49 1.501.79 1.802.00 2.012.49 2.50 2.513.00 3.014.00 4.015.00 5.016.00 6.018.00 8.0110.00 10.0112.50 12.5115.00 15.0118.00
0.13 0.13 0.13 0.13 0.14 0.14 0.15 0.17 0.18 0.20 0.22 0.32 0.35 0.37 0.40
0.17 0.18 0.20 0.21 0.22 0.23 0.34 0.37 0.40 0.45
0.16 0.17 0.18 0.20 0.21 0.23 0.33 0.36 0.38 0.42
1.201.29 1.301.49 1.501.79 1.802.49 2.503.00 3.015.00 5.016.00 6.018.00 8.0110.00 10.0112.50 12.5115.00 15.0118.00
0.07 0.07
0.07 0.08
0.08 0.09 0.09 0.10 0.16 0.18 0.19 0.20 0.17 0.18 0.19 0.21 0.10 0.11 0.17 0.19 0.20
1.201.29 1.301.49 1.501.79 1.802.00 2.012.49 2.50 2.513.00 3.014.00 4.015.00 5.016.00 6.018.00 8.0110.00 10.0112.50 12.5115.00 15.0118.00
0.17 0.17 0.17 0.17 0.18 0.18 0.20 0.22 0.24 0.26 0.29 0.32 0.35 0.37 0.40
0.23 0.24 0.26 0.28 0.29 0.31 0.34 0.37 0.40 0.45
0.21 0.22 0.24 0.26 0.28 0.30 0.33 0.36 0.38 0.42
1.201.29 1.301.49 1.501.79 1.802.49 2.503.00 3.014.00 4.015.00 5.016.00 6.018.00 8.0110.00 10.0112.50 12.5115.00 15.0118.00
0.07 0.07
0.07 0.08
0.08 0.09 0.10 0.11 0.15 0.16 0.18 0.19 0.20 0.17 0.18 0.19 0.21 0.12 0.16 0.17 0.19 0.20
1.501.89 1.901.99 2.00 2.012.50 2.512.79 2.803.00 3.014.00 4.015.00 5.016.00 6.018.00 8.0110.00 10.0112.50 12.5115.00 15.0118.00
0.17 0.17 0.17 0.18 0.20 0.20 0.22 0.24 0.26 0.29 0.32 0.35 0.37 0.40
10
Normal thickness tolerances of our products of the strength grade V. and above are specified according to DASZ 03 standard being equal to or stricter than the values specified by EN 10051 standard. Our products of the strength grade V. and above can also be ordered with reduced tolerances, if agreed.
* The thickness (h) is the dimension of the part of the material without patterns.
Length tolerances of sheets can be calculated as follows: - 0/+ 7 mm basic tolerance, + 0.6 mm/m DASZ-Dunaferr Steel Standard
11
5.4. FLATNESS
In case of ordering plain sheets the flatness tolerances, depending on the strength grades and width ranges according to EN 10051 standard, are included in the following table. Definiton of the strength grades (A, B, C, D) according to EN 10051 standard is included in chapter 2.
Width; b (mm) b 1 200 1 200 < b 1 500 b > 1 500 Flatness tolerance max. (mm/m) A 15 18 23 B 18 23 28 C 23 30 38 D as agreed as agreed as agreed
6. DIMENSIONS
The dimensions are given by strength grades. Strength grades of different qualities are included in chapter 2. on product groups.
Strength grade IV. Thickness; h (mm) Min. 1.5 1.9 2 2.8 Max. 1.89 1.99 2.79 18 Width; b (mm) Min. 800 800 800 800 Max. 1 120 1 250 1 300 1 540
Strength grade V. Thickness; h (mm) Min. 1.8 2 2.8 3 Max. 1.99 2.79 2.99 18 Width; b (mm) Min. 800 800 800 800 Max. 1 040 1 250 1 420 1 540
Strength grade VI. Thickness; h (mm) Min. 2.5 3 3.2 3.5 Max. 2.99 3.19 3.49 18.00 Width; b (mm) Min. 800 800 800 800 Max. 1 040 1 300 1 400 1 540
Strength grade VII. + VIII. Thickness; h (mm) Min. 3 3.2 3.5 4.3 Max. 3.19 3.49 3.79 15.00 Width; b (mm) Min. 840 840 840 840 Max. 1 040 1 120 1 220 1 540
12
Strength grade V. Thickness; h (mm) Min. 2.5 3.2 Max. 3.19 16.5 Width; b (mm) Min. 800 800 Max. 1 250 1 540
Teardrops
Strength grade I. + II. + III. Thickness; h (mm) Min. 1.6 1.8 2 3 Max. 1.79 1.99 2.99 16.5 Width; b (mm) Min. 840 840 800 800 Max. 1 040 1 300 1 300 1 540
Strength grade IV. Thickness; h (mm) Min. 1.6 1.9 2 3 Max. 1.89 1.99 2.99 16.5 Width; b (mm) Min. 840 840 800 800 Max. 1 040 1 250 1 250 1 540
Strength grade V. Thickness; h (mm) Min. 2.5 3.2 Max. 3.19 16.5 Width; b (mm) Min. 800 800 Max. 1 250 1 540
13
7. PACKAGING
Base types according to DASZ 34 standard Product is identified by CODE 39 bar code labels.
1. Strap under the packaging material, below the strap used outside the packaging material
14
7.2. WIDE COILS 7.2.1. Strapping of coils with coil eye in horizontal position
Width (b) <= 1 250 mm 1. banding strap 2. coil number 3. colour marking 4. self-adhesive label 5. painted black base 6. clamp 7. edge protector
15
ISD DUNAFERR Co. Ltd. SALES Address: H2400 Dunajvros, Vasm tr 13. H1022 Budapest, Bimb u. 17. Phone: +36 (1) 500-4673 Fax: +36 (1) 500-4601 E-mail: hotrolled.sales@isd-dunaferr.hu Web: www.isd-dunaferr.hu
16
2012.01.