Professional Documents
Culture Documents
230 D-90411 Nuremberg Phone: +49 911-5691-0 Fax: +49 911-5691-221 www.gmn.de Ball bearings: Phone: +49 911-56 91-249 Fax: +49 911-5691-587 email: vertrieb.kula@gmn.de
4000 0813 EN
4000 0813 EN
www.gmn.de
Contents:
Spindle ball bearings Page 8 Materials Page 10 Standard series S, SM, KH Page 14 Special designs for direct lubrication +A, +AB, +L, +LB, +AG Page 16 Special series BHT, BNT Page 19 Bearing designation Bearing data Page 20 Comparable bearing types Page 44
Deep groove ball bearings Page 45 Types, materials Page 46 Bearing designation Bearing data Page 50
Engineering Page 56 Bearing selection Page 57 Preload Page 60 Bearing arrangements Page 64 Spacers Page 66 Contact angle Matching accuracy Page 67 Precision classes Page 68 Accuracy of associated components Page 70 Bearing lubrication Page 72 Speed limits Page 80 Storage Page 82 Installation preparation Page 82
Grease distribution run Page 83 Tightening torques for precision nuts Page 84 Bearing calculation Page 86 Service life of grease Page 90 Static load capacity Page 91 Bearing frequencies Page 92
Service Bearing analysis Consultation Training courses Page 93 Special applications Page 94 Index Page 96 Internet Quality management Page 98
www.gmn.de
On the basis of long experience in the development and production of high-quality machine components, GMN has specialized in the eld of high-precision ball bearings to manufacture high performance, long-life deep groove and spindle bearings. Certication under international standards guarantees the highest levels of precision in the development and production of GMN ball bearings and secures consistently outstanding quality characteristics with regard to speed suitability, stability and durability. This comprehensive product line comprises in addition to a large number of standard solutions also special designs optimized for specic demands.
55
www.gmn.de
Series: BNT
Extra-wide design with two shields Greased Reference speed coefcient: 1.0 106 mm/min
6 6
www.gmn.de
Product characteristics:
Bore diameter 5120 mm Nominal contact angle 1525 Forces are transmitted from one raceway to the other under this pressure angle Optimized for maximum speeds Absorbs large radial and axial loads Placement against a second bearing is necessary Larger number of balls than with deep groove ball bearings Great rigidity and load capacity All series and sizes are available as hybrid bearings All GMN ball bearings are available greased All GMN bearing bore sizes are available with various outer diameters Line of ux
Outer diameter
S 618.. 18
S 619.. 19
S 60.. 10
S 62.. 02
S 60.. 10
S 619.. 19
S 618.. 18
www.gmn.de
Materials Rings
GMN uses only high-quality materials and processing techniques to manufacture all components of its high precision spindle ball bearings. The highest standards of quality assure the best possible performance efciency and optimal service life for GMN products.
Cages
GMN ball bearing components are continuously being optimized by ongoing development efforts to further improve their technical characteristics. Due to their outstanding characteristics, cage types TA and TXM exhibit exceptional performance with respect to speed, load capacity and service life.
TA cage
TXM cage
Advantages: High resistance to wear Outstanding emergency operating characteristics due to favorable sliding properties and reduced abrasion Reduced operating temperature due to lower friction and more favorable tribology Constant grease lubrication due to the formation of grease reservoirs in provided cage pockets Long service life
Material Bearing steel (chrome steel) 100 Cr 6 Material no. 1.3505, SAE 52100, SUJ2 Special steels on request Permissible operating temperature Heat treated for continuous operating temperatures up to 150C Hardness 60 to 64 HRC, fully hardened; corresponds to 700800 HV30 Characteristics High purity and homogeneity, vacuum-degassed
Material Laminated phenolic resin Phenolic resin with ne mesh cotton webbing Permissible operating temperature 120C Cage guidance on outer ring Fabrication machining Application for S, SM, KH series general purpose Characteristics low friction coefcient, for oil and grease lubrication
Increased cost effectiveness Material Partially crystalline high performance plastic PEEK (polyetheretherketone), carbon ber reinforced Permissible operating temperature 250C Cage guidance on outer ring, ball retaining Fabrication injection molded Application for S, SM series optimized for grease lubrication Characteristics low friction coefcient, reduces/eliminates cage vibrations great mechanical, chemical and thermal stability 140% 120% 100% 80% 60% TXM cage 20% 0% TXM cage 40% TA cage TA cage
Other cage materials, types, special treatments (e.g. TB, brass, Torlon, silver-coated aluminum bronze) are available on request.
10
11
www.gmn.de
Materials Balls
Bore/roll ratio
Steel 100 Cr 6
Ceramic Si3N4
0.5
1.5
2.5
120 100 80 60 40 20 0
Material Bearing steel (chrome steel) 100 Cr 6 Material no. 1.3505, SAE 52100, SUJ2 Special steels on request Permissible operating temperature Heat treated for continuous operating temperatures up to 150C Hardness 60 to 64 HRC, fully hardened; corresponds to 700800 HV30 Characteristics High purity and homogeneity, vacuum-degassed
Material Ceramic (silicon nitride Si3N4) Material characteristics Low chemical afnity to 100 Cr 6 Low friction coefcient Low heat conductivity Corrosion resistance Non magnetic Electrically insulating
Steel 100 Cr 6
0.5
1.5
2.5
25% 0%
Density E-modulus
Expansion coefcient
12
13
www.gmn.de
Standard series
Standard S, SM and KH series spindle bearings from GMN cover a comprehensive range of sizes, types and designs. Based on a diverse choice of products, GMN offers quality-oriented and economic spindle bearing solutions for a large number of specic requirements.
Series S
Series SM
Series KH
The GMN Series S product line covers an extensive range of dimensions, speed suitability and load carrying capacity. Standard spindle bearings High speed suitability and rigidity Highly economical and reliable
Due to optimized inner geometry, GMN Series SM permits almost 20 % higher speeds in comparison to Series S. Optimized inner ring bevel form for high speeds Long service life because friction is minimized Highly resistant to temperature inuences due to large radial bearing clearance Low operating temperature due to minimal friction
Because bearing geometry is optimized, the GMN Series KH provides outstanding speed properties, service life and economy. Sealed: with permanent grease lubrication Standard grease (Lubcon HS Turmogrease L252) or customer-specic grease Open: for oil lubrication Optimized for highest speeds Low operating temperature due to optimized raceway geometry High resistance to temperature inuences due to large radial bearing clearance Optimized ratio of ball complement and ball diameter to load rating Optimized inner geometry with respect to grease space and oil lubrication No reduction of speed due to non-contact seals (seal temperature stable up to 120C) No grease escapes in vertical or inclined installation position Reduced grease desiccation due to air ow No additional sealing elements needed Less sensitive to assembly area contamination
14
15
www.gmn.de
Special design +A
Oil supply
Special design +L
Oil supply
Lubrication hole to the raceway on the open side Optimized for highest speeds Reduced bearing wear High operating security Sufx A (designation example: HY SMA 6005)
Lubrication hole to the raceway on the closed side Optimized for highest speeds Reduced bearing wear High operating security Sufx AB (designation example: HY SMAB 6006)
Lubrication hole to the raceway on the open side and sealed with O-rings Optimized for highest speeds Reduced bearing wear High operating security High oil position compatibility (ring groove) in the housing Additional outer ring seal Sufx L (designation example: HY SML 6007)
Lubrication hole to the raceway on the closed side and sealed with O-rings Optimized for highest speeds Reduced bearing wear High operating security High oil position compatibility (ring groove) in the housing Additional outer ring seal Sufx LB (designation example: HY SMLB 6008)
16
17
www.gmn.de
Re-lubrication system
Series BNT
Bevel form as series S
Series BHT
Bevel form as series SM
Lubrication holes to the raceway on the open side Optimized for maximum speeds (speed factor n dm up to 2.3 106 mm/min) Maximum service life (up to factor 10) Reduced overhead for grease distribution High operating security Low capital expenditure Sufx AG (designation example: HY SMAG 6005)
Re-lubrication unit and lubricant supply Exactly dosed and delivered grease quantity Lubricant matched to bearing requirements Small space requirement Simple assembly and handling Minimal operating costs (no compressed air, oil consumption) Fully automatic or machine controlled lubrication Individually programmable operating time Minimum design effort Complete bearing Increase of permissible speed range with grease lubrication Optimal, long-term lubricant supply Simple system technology
Ball-retaining cage (balls do not fall out when the inner ring is removed) Cage is guided by outer ring shoulders Simple assembly (inner and outer rings are installed separately) Rotating parts can be balanced with inner ring installed Bearing axial clearance can be dened
Ball-retaining cage (balls do not fall out when the inner ring is removed) Cage is guided by outer ring shoulders Simple assembly (inner and outer rings are installed separately) Rotating parts can be balanced with inner ring installed Bearing axial clearance can be dened
18
19
www.gmn.de
HY
SM
08 2RZ C TA P4 R D A 60 U L
- L2 5
2
Lubrication - A AB L LB AG Bearing size Seal Nominal contact angle Cage Precision 6008 2RZ C E 18 TA TXM P4 P2 A7 A9 HG UP
High point R marking Ri Ra Bearing sets Matching and preload Lubrication D T Q UL UM US UV B F T - L252
20
13 21
www.gmn.de
r1
r3
r1
r3
ra
rb
D1 dm
r1
r2
r2
r1
d1
D2
D1 dm
d2
r1
r2
r1
r2
ra d d1 D2 Da db da dT Db
ra
Boundary dimensions d [mm] Bore diameter D [mm] Outer diameter B [mm] Width of single bearing Balls dm Dw Z [mm] [mm] pieces Pitch circle diameter Ball diameter Number of balls Outer diameter of inner ring Outer diameter of inner ring (open side)
D1 D2 r 1,2 r 3,4
Inner diameter of outer ring Inner diameter of outer ring (open side) Chamfer (min) Chamfer; open side (min)
Abutment diameter outer ring Oiling nozzle position for bearings with TA cage (for TXM cage on request) Bearing weight Contact angle Dynamic load rating Static load rating, steel balls Static load rating, Si3N4 balls
Abutment dimensions ra max [mm] Undercut of associated component rb max [mm] Undercut of associated component (open side) da min [mm] Abutment diameter inner ring db min [mm] Abutment diameter inner ring Da max [mm] Abutment diameter outer ring
Preload / axial rigidity Fv [N] Preload Cax [N/m] Axial rigidity (bearing pair) L light preload M medium preload S heavy preload Ff [N] Minimum spring preload at max. speed
Spring preload
d m
DW
d1
d2
D1
D2
r1,2
dT
0 15 15 15 15 15 15 15 15
C0
C0 HY
noil
ngrease
Fv
Cax
Fv
Cax
Fv
Cax
Ff
Designation 5 mm
5 5 5 5 6 6 6 6
13 14 14 16 15 17 17 19
4 5 5 5 5 6 6 6
8 8 8 7 9 9 9 10
11.3 0.2 0.2 11.0 0.2 0.2 11.0 0.2 0.2 13.2 0.3 0.3 12.7 0.2 0.2 12.4 0.3 0.3 12.4 0.3 0.3
190000 140000 195000 145000 230000 170000 170000 125000 165000 125000 170000 125000 200000 150000 125000 94000
6 7 5 10 7 8 6 15
7 8 5 9 8 9 7 13
18 20 14 30 20 25 18 40
11 13 9 14 12 16 11 20
36 40 28 60 40 45 32 80
15 20 13 21 17 22 15 29
35 40 30 50 35 40 35 70
0.3 0.15
www.gmn.de
7 to 10 mm
Boundary dimensions Balls Dimensions Abutment dimensions Weight Contact Load rating Speed value Preload/axial rigidity angle Spring preload
Designation 7 mm S 619/7 C TA S 607 C TA S 627 C TA 8 mm S 619/8 C TA S 608 C TA 9 mm S 619/9 C TA S 609 C TA S 629 C TA 10 mm S 61800 C TA S 61800 E TA S 61900 C TA S 61900 E TA SM 61900 C TA KH 61900 C TA KH 61900 E TA S 6000 C TA S 6000 E TA SM 609 C TA SM 608 C TA
d m
DW
d1
d2
D1
D2
r1,2
dT
0 15 15 15 15 15 15 15 15 15 15 15 15 25 15 25 15 17 25 15 25 15 17 25 15 25
C0
C0 HY
noil
ngrease
Fv
Cax
Fv
Cax
Fv
Cax
Ff
Designation 7 mm
7 7 7 7 8 8 8 9 9 9 9 10 10 10 10 10 10 10 10 10 10 10 10 10 10
17 19 19 22 19 22 22 20 24 24 26 19 19 22 22 22 22 22 26 26 26 26 26 30 30
5 6 6 7 6 7 7 6 7 7 8 5 5 6 6 6 6 6 8 8 8 8 8 9 9
12.0 2.381 13.0 3.175 13.0 3.175 14.5 3.969 13.5 3.175 15.0 3.969 15.0 3.969 14.5 16.5 16.5 17.5 3.175 3.969 3.969 4.762
11 10 10 9 10 9 9 11 10 10 10 13 13 11 11 11 14 14 10 10 10 11 11 10 10
10.0 10.7 10.7 11.8 10.7 11.8 11.8 12.4 13.5 13.5 14.7 12.8 12.8 13.6 13.6 13.6 13.6 13.6 13.3 13.3
14.1
0.3 0.3
0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3
0.1 0.1 0.1 0.15 0.1 0.1 0.1 0.1 0.1 0.1 0.15 0.15 0.15 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1
9.0 9.5 9.5 10.0 10.0 10.5 10.5 11.5 11.5 11.5 13.0 12.0 12.0 12.5 12.5 12.5 12.5 12.5 12.5 12.5 12.5 12.5 12.5 14.5 14.5
15.0 16.5 16.5 19.0 17.0 19.0 19.0 18.0 21.0 21.0 23.0 17.0 17.0 19.5 19.5 19.5 19.5 19.5 23.0 23.0 23.0 23.0 23.0 25.5 25.5
10.9 12.1 12.1 13.4 12.2 13.4 13.4 13.7 15.2 15.2 16.5 13.6 13.6 14.7 14.7 14.7 14.5 14.5 16.5 16.5 16.5 15.9 15.9 18.3 18.3
0.005 0.007 0.007 0.013 0.007 0.010 0.010 0.007 0.014 0.014 0.020 0.005 0.005 0.010 0.010 0.010 0.010 0.010 0.018 0.018 0.018 0.018 0.018 0.030 0.030
1510 2600 1920 3400 2600 3400 2700 2800 3750 2950 5450 1660 1500 2800 2700 2080 1420 1360 5450 5250 3950 2020 1950 7500 7250
655 1170 675 1460 1170 1460 980 1330 1710 1150 2600 830 725 1360 1300 810 590 565 2600 2550 1530 780 750 3750 3600
460 820 475 1030 820 1030 685 940 1200 810 1830 580 510 960 920 565 415 400 1830 1760 1070 550 530 2650 2550
145000 110000 125000 115000 125000 115000 94000 86000 94000 86000 150000 110000
8 12 10 20 12 17 13 12 20 16 30 8 13 12 22 11 7 11 25 45 18 10 16 40 60
9 11 10 13 12 12 10 13 14 12 19 10 25 13 32 11 12 25 17 42 13 12 26 23 54
15 20 15 19 19 20 16 21 24 20 30 17 39 21 50 16 18 37 30 65 22 19 39 39 81
46 80 60 100 70 100 80 75 120 100 160 50 80 75 140 65 45 70 160 260 110 60 100 230 360
21 30 21 28 27 28 22 29 35 27 42 23 51 29 65 23 25 49 43 87 29 26 51 54 110
S 619/7 C TA S 607 C TA SM 607 C TA S 627 C TA 8 mm S 619/8 C TA S 608 C TA SM 608 C TA 9 mm S 619/9 C TA S 609 C TA SM 609 C TA S 629 C TA 10 mm S 61800 C TA S 61800 E TA S 61900 C TA S 61900 E TA SM 61900 C TA KH 61900 C TA KH 61900 E TA S 6000 C TA S 6000 E TA SM 6000 C TA KH 6000 C TA KH 6000 E TA S 6200 C TA S 6200 E TA
16.5 0.3 0.3 16.5 0.3 0.3 18.6 0.3 0.3 16.5 0.3 0.3 18.6 0.3 0.3 18.6 0.3 0.3 17.9 0.3 0.2
SM 607 C TA
136000 100000 115000 102000 120000 94000 115000 100000 110000 92000 125000 125000 95000 80000 111000 125000 110000 85000 72000 86000 76000 90000 70000 86000 75000 82000 69000 94000 94000 71000 60000 83000 94000 82000 64000 54000
19.9 20.6 0.3 0.3 19.9 20.6 0.3 0.3 21.4 16.2 16.2 17.8 17.8 17.8 17.8 17.8 21.4 21.4 21.4 20.5 20.5 24.5 24.5 22.7 0.3 0.3 16.9 0.3 0.2 16.9 0.3 0.2 18.8 0.3 0.3 18.8 0.3 0.3 18.8 0.3 0.3 18.5 0.3 0.3 18.5 0.3 0.3 22.7 0.3 0.3 22.7 0.3 0.3 22.7 0.3 0.3 21.3 0.3 0.3 21.3 0.3 0.3
14.5 2.381 14.5 2.381 16.0 16.0 16.0 3.175 3.175 3.175
16.0 2.381 16.0 2.381 18.0 4.762 18.0 4.762 18.0 4.762 18.0 18.0 3.175 3.175
135000 100000
16.0 16.0
25.5 0.6 0.6 0.6 0.3 25.5 0.6 0.6 0.6 0.3
24
25
www.gmn.de
12 to 15 mm
Boundary dimensions Balls Dimensions Abutment dimensions Weight Contact Load rating Speed value Preload/axial rigidity angle Spring preload
d m
DW
d1
d2
D1
D2
r1,2
dT
0 15 25 15 25 15 17 25 15 25 15 17 25 15 25 15 25 15 25 15 17 25 15 25 15 17 25 15 25
C0
C0 HY
noil
ngrease
Fv
Cax
Fv
Cax
Fv
Cax
Ff
Designation 12 mm
12 12 12 12 12 12 12 12 12 12 12 12 12 12 15 15 15 15 15 15 15 15 15 15 15 15 15 15
21 21 24 24 24 24 24 28 28 28 28 28 32 32 24 24 28 28 28 28 28 32 32 32 32 32 35 35
5 5 6 6 6 6 6 8 8 8 8 8 10 10 5 5 7 7 7 7 7 9 9 9 9 9 11 11
16.5 16.5 18.0 18.0 18.0 18.0 18.0 20.0 20.0 20.0 19.0 19.0 22.0 22.0 19.5 19.5 21.5 21.5 21.5 21.5 21.5
2.381 2.381 3.175 3.175 3.175 2.381 2.381 4.762 4.762 4.762 3.175 3.175 5.953 5.953 2.381 2.381 3.969 3.969 3.969 2.778 2.778
15 15 13 13 13 15 15 11 11 11 13 13 10 10 17 17 13 13 13 16 16 13 13 13 13 13 11 11
18.0 18.6 0.3 0.2 18.0 18.6 0.3 0.2 19.6 20.6 0.3 0.3 19.6 20.6 0.3 0.3 19.6 20.6 0.3 0.3 19.6 20.3 0.3 0.3 19.6 20.3 0.3 0.3 23.4 24.7 0.3 0.3 23.4 24.7 0.3 0.3 23.4 24.7 0.3 0.3 22.5 23.3 0.3 0.3 22.5 23.3 0.3 0.3
0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3
0.15 0.15 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1
14.0 14.0 14.5 14.5 14.5 14.5 14.5 14.5 14.5 14.5 14.5 14.5 16.5 16.5 17.0 17.0 17.5 17.5 17.5 17.5 17.5 17.5 17.5 17.5 17.5 17.5 19.5 19.5
19.0 19.0 21.5 21.5 21.5 21.5 21.5 25.0 25.0 25.0 25.0 25.0 27.5 27.5 22.0 22.0 25.5 25.5 25.5 25.5 25.5 29.0 29.0 29.0 29.0 29.0 30.5 30.5
15.4 15.4 16.5 16.5 16.5 16.3 16.3 18.5 18.5 18.5 18.0 18.0 20.5 20.5 18.6 18.6 20.2 20.2 20.2 19.9 19.9 21.9 21.9 21.9 21.6 21.6 23.4 23.4
0.006 0.006 0.011 0.011 0.011 0.011 0.011 0.020 0.020 0.020 0.020 0.020 0.037 0.037 0.007 0.007 0.015 0.015 0.015 0.015 0.015 0.028 0.028 0.028 0.028 0.028 0.044 0.044
1800 1710 3100 2950 2330 1480 1410 5900 5650 4300 2260 2180 8300 8000 1900 1790 4500 4300 3600 2010 1930 6650 6350 4900 3400 3300 9000 8700
980 930 1660 1580 990 650 620 3000 2900 1750 950 920 4150 4050 1150 1090 2450 2330 1560 940 900 3750 3600 2140 1470 1420 4850 4700
685 650 1170 1110 695 455 440 2100 2020 1230 670 645 2950 2850 810 770 1720 1640 1100 660 630 2650 2550 1510 1040 1000 3450 3300
105000 89000 97000 83000 115000 120000 110000 85000 72500 100000 110000 100000 77000 66000 87000 74000 79000 67000 93000 100000 90000 72000 62000 85000 92000 83000 67000 57000
79000 67000 73000 62000 86000 90000 82000 64000 54000 75000 82000 75000 58000 49000 65000 55000 59000 50000 70000 75000 67000 54000 46000 64000 69000 62000 50000 43000
9 15 15 25 12 7 12 30 50 22 11 18 42 70 10 15 22 35 18 10 16 32 55 22 17 30 45 75
12 29 15 37 13 12 26 20 47 15 15 30 23 56 13 32 18 44 15 15 32 22 54 17 18 39 25 61
18 44 24 56 19 19 39 33 70 24 22 45 39 84 21 48 29 68 24 23 48 38 82 28 27 55 41 93
55 90 85 150 70 45 70 180 280 130 70 110 250 400 60 90 140 220 110 60 100 200 320 150 100 160 270
26 58 34 74 26 26 51 48 95 33 30 59 54 112 29 62 42 89 33 31 64 55 110 38 36 72 59
50 65 80 110 70 55 70 155 205 130 85 105 215 290 50 65 115 160 110 75 95 170 235 150 125 160 230 320
S 61801 C TA S 61801 E TA S 61901 C TA S 61901 E TA SM 61901 C TA KH 61901 C TA KH 61901 E TA S 6001 C TA S 6001 E TA SM 6001 C TA KH 6001 C TA KH 6001 E TA S 6201 C TA S 6201 E TA 15 mm S 61802 C TA S 61802 E TA S 61902 C TA S 61902 E TA SM 61902 C TA KH 61902 C TA KH 61902 E TA S 6002 C TA S 6002 E TA SM 6002 C TA KH 6002 C TA KH 6002 E TA S 6202 C TA S 6202 E TA 27
SM 6001 C TA KH 6001 C TA KH 6001 E TA S 6201 C TA S 6201 E TA 15 mm S 61802 C TA S 61802 E TA S 61902 C TA S 61902 E TA SM 61902 C TA KH 61902 C TA KH 61902 E TA S 6002 C TA S 6002 E TA
18.3 18.3 17.8 17.8 18.7 18.7 18.7 18.7 18.7 18.3 18.3
26.0 27.9 0.6 0.6 0.6 0.3 26.0 27.9 0.6 0.6 0.6 0.3 21.2 21.2 21.8 0.3 0.2 21.8 0.3 0.2 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.15 0.15 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1
24.3 25.4 0.3 0.3 24.3 25.4 0.3 0.3 24.3 25.4 0.3 0.3 23.9 24.5 0.3 0.3 23.9 24.5 0.3 0.3 26.9 28.2 0.3 0.3 26.9 28.2 0.3 0.3 26.9 28.2 0.3 0.3 26.7 28.0 0.3 0.3 26.7 28.0 0.3 0.3 29.0 29.0 31.3 0.6 0.3 31.3 0.6 0.3
23.5 4.762 23.5 4.762 23.5 4.762 23.5 3.969 23.5 3.969 25.0 5.953 25.0 5.953
21.1 21.1
440 123
www.gmn.de
17 to 20 mm
Boundary dimensions Balls Dimensions Abutment dimensions Weight Contact Load rating Speed value Preload/axial rigidity angle Spring preload
Designation 17 mm S 61803 C TA S 61803 E TA S 61903 C TA S 61903 E TA SM 61903 C TA KH 61903 C TA KH 61903 E TA S 6003 C TA S 6003 E TA
d m
DW
d1
d2
D1
D2
r1,2
dT
0 15 25 15 25 15 17 25 15 25 15 17 25 15 25 15 25 15 25 15 17 25 15 25 15 17 25 15 25
C0
C0 HY
noil
ngrease
Fv
Cax
Fv
Cax
Fv
Cax
Ff
Designation 17 mm
17 17 17 17 17 17 17 17 17 17 17 17 17 17 20 20 20 20 20 20 20 20 20 20 20 20 20 20
26 26 30 30 30 30 30 35 35 35 35 35 40 40 32 32 37 37 37 37 37 42 42 42 42 42 47 47
5 5 7 7 7 7 7 10 10 10 10 10 12 12 7 7 9 9 9 9 9 12 12 12 12 12 14 14
19 19 14 14 14 18 18 14 14 14 15 15 11 11 18 18 15 15 15 16 16 13 13 13 14 14 11 11
19.8 19.8 21.0 21.0 21.0 21.0 20.6 21.0 20.6 22.7 22.7 22.7 22.7 22 22.7 22 24.1 24.1 23.9 23.9 25.1 25.1 25.1 25.1 25.1 24.5 24.5
23.2 23.8 0.3 23.2 23.8 0.3 26.6 26.6 26.6 27.7 0.3 27.7 0.3 27.7 0.3
0.2 0.2 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3
0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3
0.15 0.15 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.3 0.3 0.15 0.15 0.15 0.15 0.15 0.15 0.15
19.0 19.0 19.5 19.5 19.5 19.5 19.5 20.0 20.0 20.0 20.0 20.0 21.5 21.5 23.0 23.0 23.0 23.0 23.0 23.0 23.0 25.0 25.0 25.0 25.0 25.0 26.0 26.0
24.0 24.0 27.5 27.5 27.5 27.5 27.5 31.5 31.5 31.5 31.5 31.5 35.0 35.0 29.0 29.0 33.5 33.5 33.5 33.5 33.5 37.0 37.0 37.0 37.0 37.0 41.0 41.0
20.6 20.6 22.5 22.5 22.5 22.2 22.2 24.4 24.4 24.4 24.2 24.2 26.6 26.6 24.9 24.9 26.9 26.9 26.9 26.6 26.6 29.0 29.0 29.0 28.6 28.6 31.4 31.4
0.008 0.008 0.017 0.017 0.017 0.017 0.017 0.037 0.037 0.037 0.037 0.037 0.065 0.065 0.018 0.018 0.036 0.036 0.036 0.036 0.036 0.063 0.063 0.063 0.063 0.063 0.105 0.105
2000 1890 4700 4450 3750 2150 2060 6950 6650 5150 3750 3600 11400 11000 3650 3450 7250 6850 5400 3900 3700 12200 11700 8300 6500 6300 16900 16200
1310 1240 2700 2600 1750 1070 1020 4150 4000 2410 1750 1680 6350 6100 2500 2380 4600 4350 2700 1900 1820 7600 7300 3800 3050 2950 10000 9800
920 870 1900 1810 1230 760 720 2950 2800 1690 1230 1180 4450 4300 1760 1680 3200 3050 1870 1340 1280 5350 5150 2700 2140 2060 7050 6850
79000 67000 71000 61000 84000 90000 82000 65000 56000 77000 82000 74000 60000 51000 65000 56000 60000 51000 70000 75000 68000 55000 47000 65000 70000 63000 51000 43000
59000 50000 53000 46000 63000 67000 61000 49000 42000 58000 61000 55000 45000 38000 49000 42000 45000 38000 52000 56000 51000 41000 35000 49000 52000 47000 38000 32000
10 16 25 40 19 11 17 35 60 25 19 30 60 90 19 30 35 55 30 20 30 60 100 40 35 50 85 140
14 35 20 49 16 17 35 24 58 19 20 42 29 69 21 49 26 62 22 21 44 33 78 24 27 54 38 91
30 50 75 120 55 35 50 105 170 80 55 90 170 280 55 90 110 170 80 60 90 180 300 120 100 160 260 410
60 100 150 240 110 65 100 210 340 160 110 180 350 560 110 170 220 340 170 120 180 360 600 240 200 500
55 70 120 165 115 80 100 180 245 155 135 175 295 400 95 130 185 250 165 140 180 315 425 250 235 300 435 590
S 61803 C TA S 61803 E TA S 61903 C TA S 61903 E TA SM 61903 C TA KH 61903 C TA KH 61903 E TA S 6003 C TA S 6003 E TA SM 6003 C TA KH 6003 C TA KH 6003 E TA S 6203 C TA S 6203 E TA 20 mm S 61804 C TA S 61804 E TA S 61904 C TA S 61904 E TA SM 61904 C TA KH 61904 C TA KH 61904 E TA S 6004 C TA S 6004 E TA SM 6004 C TA KH 6004 C TA KH 6004 E TA S 6204 C TA S 6204 E TA 29
26.2 26.8 0.3 26.2 26.8 0.3 29.4 30.7 0.3 29.4 30.7 0.3 29.4 30.7 0.3 29.8 30.4 0.3 29.8 30.4 0.3 33.0 33.0 28.1 28.1 31.9 31.9 31.9 35.2 0.6 35.2 0.6 29.1 0.3 29.1 0.3 33.2 0.3 33.2 0.3 33.2 0.3
26.0 4.762 26.0 4.762 26.0 4.762 26.0 3.969 26.0 3.969 28.5 28.5 26.0 26.0 28.5 28.5 28.5 28.5 28.5 31.0 31.0 31.0 31.0 31.0 33.5 33.5 6.747 6.747 3.175 3.175 4.762 4.762 4.762 3.969 3.969 6.35 6.35 6.35 5.556 5.556 7.938 7.938
SM 6003 C TA KH 6003 C TA KH 6003 E TA S 6203 C TA S 6203 E TA 20 mm S 61804 C TA S 61804 E TA S 61904 C TA S 61904 E TA SM 61904 C TA KH 61904 C TA KH 61904 E TA S 6004 C TA S 6004 E TA
0.3 0.6 0.3 0.6 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3
37.3 0.6 0.3 0.6 0.3 37.3 0.6 0.3 0.6 0.3 37.3 0.6 0.3 0.6 0.3
26.6 25.3 36.4 38.0 0.6 0.3 0.6 0.3 26.6 25.3 36.4 38.0 0.6 0.3 0.6 0.3 28.5 38.6 28.5 38.6 41.4 1.0 41.4 1.0 0.6 1.0 0.6 1.0 0.6 0.6
www.gmn.de
25 to 30 mm
Boundary dimensions Balls Dimensions Abutment dimensions Weight Contact Load rating Speed value Preload/axial rigidity angle Spring preload
Designation 25 mm S 61805 C TA S 61805 E TA S 61905 C TA S 61905 E TA SM 61905 C TA KH 61905 C TA KH 61905 E TA S 6005 C TA S 6005 E TA
d m
DW
d1
d2
D1
D2
r1,2
dT
0 15 25 15 25 15 17 25 15 25 15 17 25 15 25 15 25 15 25 15 17 25 15 25 15 17 25 15 25
C0
C0 HY
noil
ngrease
Fv
Cax
Fv
Cax
Fv
Cax
Ff
Designation 25 mm
25 25 25 25 25 25 25 25 25 25 25 25 25 25 30 30 30 30 30 30 30 30 30 30 30 30 30 30
37 37 42 42 42 42 42 47 47 47 47 47 52 52 42 42 47 47 47 47 47 55 55 55 55 55 62 62
7 7 9 9 9 9 9 12 12 12 12 12 15 15 7 7 9 9 9 9 9 13 13 13 13 13 16 16
31.0 31.0 33.5 33.5 33.5 33.5 33.5 36.0 36.0 36.0 36.0 36.0 38.5 38.5 36.0 36.0 38.5 38.5 38.5 38.5 38.5 42.5 42.5 42.5 42.5 42.5
3.175 3.175 4.762 4.762 4.762 3.969 3.969 6.35 6.35 6.35 5.556 5.556 7.938 7.938 3.175 3.175 4.762 4.762 4.762
19 19 17 17 17 19 19 15 15 15 17 17 13 13 22 22 18 18 18
28.9 28.9 30.6 30.6 30.6 30.6 30 30.6 30 32.2 32.2 32.2 32.2 30.9 32.2 30.9 34.0 34.0 34.1 34.1 35.1 35.1 35.1 35.1 35.1 35 35
33.1 33.1
28.0 28.0 28.0 28.0 28.0 28.0 28.0 30.0 30.0 30.0 30.0 30.0 31.0 31.0 33.0 33.0 33.0 33.0 33.0 33.0 33.0 36.0 36.0 36.0 36.0 36.0 36.0 36.0
34.0 34.0 38.5 38.5 38.5 38.5 38.5 42.0 42.0 42.0 42.0 42.0 46.0 46.0 39.0 39.0 43.5 43.5 43.5 43.5 43.5 49.0 49.0 49.0 49.0 49.0 55.0 55.0
29.9 29.9 32.4 32.4 32.4 32.1 32.1 34.3 34.3 34.3 34.2 34.2 36.8 36.8 35.1 35.1 36.8 36.8 36.8 36.5 36.5 40.5 40.5 40.5 40.1 40.1 43.6 43.6
0.021 0.021 0.041 0.041 0.041 0.041 0.041 0.076 0.076 0.076 0.076 0.076 0.128 0.128 0.025 0.025 0.047 0.047 0.047 0.047 0.047 0.112 0.112 0.112 0.112 0.112 0.199 0.199
3650 3450 7700 7300 5800 4250 4100 13400 12700 9200 7400 7100 19000 18200 3850 3650 7800 7400 5950 4650 4400 16500 15700 11900 8200 7800 25000 24000
2750 2600 5400 5100 3150 2330 2220 9200 8800 4700 3900 3750 12600 12000 3250 3100 5850 5550 3400 2750 2650 11900 11400 6450 4700 4500 16700 16100
1930 1830 3800 3600 2200 1640 1560 6500 6200 3300 2750 2650 8900 8400 2280 2150 4100 3900 2380 1930 1840 8400 8000 4550 3350 3200 11800 11300
55000 47000 50000 43000 59000 63000 57000 47000 40000 55000 59000 53000 44000 37000 47000 40000 44000 38000 52000 55000 50000 40000 34000 47000 50000 46000 37000 32000
41000 35000 37000 32000 44000 47000 43000 35000 30000 41000 44000 40000 33000 27500 35000 30000 33000 28500 39000 41000 37000 30000 25500 35000 37000 34000 27500 24000
21 51 29 70 23 25 52 38 88 28 30 65 45 104 24 56 30 72 24 28 58 43 98 32 35 74 49
55 90 120 180 90 65 100 200 320 140 110 180 300 450 60 90 120 190 90 70 110 250 400 180 120 200 380
110 170 240 360 180 130 200 400 280 220 360 600 900 120 240 180 140 220 500 360 250 390 760
95 130 200 265 175 155 195 345 465 280 265 340 485 660 100 135 200 270 180 170 210 425 570 360 295 375 640 880
S 61805 C TA S 61805 E TA S 61905 C TA S 61905 E TA SM 61905 C TA KH 61905 C TA KH 61905 E TA S 6005 C TA S 6005 E TA SM 6005 C TA KH 6005 C TA KH 6005 E TA S 6205 C TA S 6205 E TA 30 mm S 61806 C TA S 61806 E TA S 61906 C TA S 61906 E TA SM 61906 C TA KH 61906 C TA KH 61906 E TA S 6006 C TA S 6006 E TA SM 6006 C TA KH 6006 C TA KH 6006 E TA S 6206 C TA S 6206 E TA 31
37.4 38.7 0.3 0.3 37.4 38.7 0.3 0.3 37.4 38.7 0.3 0.3 37.2 37.2 40.1 40.1 40.1 38.5 0.3 0.3 38.5 0.3 0.3 42.3 0.6 0.3 42.3 0.6 0.3 42.3 0.6 0.3
0.6 0.3 0.6 0.3 0.6 0.3 0.6 0.3 0.6 0.3 0.6 0.6 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.3 0.3 0.3 0.3 0.3 0.6 0.6
640 180
SM 6005 C TA KH 6005 C TA KH 6005 E TA S 6205 C TA S 6205 E TA 30 mm S 61806 C TA S 61806 E TA S 61906 C TA S 61906 E TA SM 61906 C TA KH 61906 C TA KH 61906 E TA S 6006 C TA S 6006 E TA
42.0 43.6 0.6 0.3 42.0 43.6 0.6 0.3 44.1 44.1 46.9 1.0 46.9 1.0
0.6 1.0 0.6 1.0 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3
38.3 39.3 0.3 38.3 39.3 0.3 41.9 43.2 0.3 41.9 43.2 0.3 41.9 43.2 0.3 41.7 41.7 43.0 0.3 43.0 0.3
47.0 49.5 1.0 47.0 49.5 1.0 47.0 49.5 1.0 47.9 49.5 1.0 47.9 49.5 1.0 52.1 52.1 55.4 1.0 55.4 1.0
0.6 1.0 0.6 1.0 0.6 1.0 0.6 1.0 0.6 1.0 0.6 1.0 0.6 1.0
800 205
40.4 40.4
117 600
1200 239
www.gmn.de
35 to 40 mm
Boundary dimensions Balls Dimensions Abutment dimensions Weight Contact Load rating Speed value Preload/axial rigidity angle Spring preload
Designation 35 mm S 61807 C TA S 61807 E TA S 61907 C TA S 61907 E TA SM 61907 C TA KH 61907 C TA KH 61907 E TA S 6007 C TA S 6007 E TA
d m
DW
d1
d2
D1
D2
r1,2
dT
0 15 25 15 25 17 17 25 15 25 15 17 25 15 25 15 25 15 25 17 17 25 15 25 15 17 25 15 25
C0
C0 HY
noil
ngrease
Fv
Cax
Fv
Cax
Fv
Cax
Ff
Designation 35 mm
35 35 35 35 35 35 35 35 35 35 35 35 35 35 40 40 40 40 40 40 40 40 40 40 40 40 40 40
47 47 55 55 55 55 55 62 62 62 62 62 72 72 52 52 62 62 62 62 62 68 68 68 68 68 80 80
7 7 10 10 10 10 10 14 14 14 14 14 17 17 7 7 12 12 12 12 12 15 15 15 15 15 18 18
41.0 41.0 45.0 45.0 45.0 45.0 45.0 48.5 48.5 48.5 48.5 48.5 53.5 53.5
24 24 18 18 18
38.9 38.9 41.4 41.4 41.4 41.4 40.8 41.4 40.8 43.2 43.2 43.2 43.2 43.2 41.5 41.5
43.1 43.1
44.1 44.1
0.3 0.3
0.3 0.3
0.3 0.3
0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.3 0.3 0.3 0.3 0.3 0.6 0.6 0.15 0.15
38.0 38.0 40.0 40.0 40.0 40.0 40.0 41.0 41.0 41.0 41.0 41.0 43.0 43.0 43.0 43.0 45.0 45.0 45.0 45.0 45.0 46.0 46.0 46.0 46.0 46.0 48.0 48.0
44.0 44.0 50.5 50.5 50.5 50.5 50.5 56.0 56.0 56.0 56.0 56.0 64.0 64.0 49.0 49.0 57.5 57.5 57.5 57.5 57.5 62.0 62.0 62.0 62.0 62.0 72.0 72.0
39.9 39.9 43.3 43.3 43.3 43.0 43.0 46.1 46.1 46.1 45.5 45.5 50.9 50.9 44.9 44.9 49.0 49.0 49.0 48.3 48.3 51.8 51.8 51.8 51.4 51.4 56.9 56.9
0.028 0.028 0.075 0.075 0.075 0.075 0.075 0.149 0.149 0.149 0.149 0.149 0.290 0.290 0.031 0.031 0.109 0.109 0.109 0.109 0.109 0.185 0.185 0.185 0.185 0.185 0.368 0.368
3950 3750 10900 10300 8000 5050 4800 20600 19600 14300 10400 10000 35000 33500 4050 3800 14900 14100 10400 6850 6550 22000 20900 15400 10900 10500 36500 35000
3600 3400 8700 8200 4750 3300 3150 15500 14800 8000 6150 5900 24300 23200 3950 3700 12700 12100 6350 4550 4300 17900 17100 9300 6900 6550 25500 24400
2550 2370 6100 5750 3350 2320 2210 10900 10400 5650 4350 4150 17100 16300 2750 2600 9000 8500 4500 3200 3050 12600 12000 6500 4850 4650 17900 17200
41000 35000 38000 32000 44000 47000 43000 35000 30000 41000 44000 40000 32000 27000 37000 32000 33000 28500 39000 42000 38000 31500 27000 37000 39000 36000 28500 24000
31000 26000 28500 24000 33000 35000 32000 26000 22500 31000 33000 30000 24000 20000 27500 24000 24500 21500 29000 31000 28500 23500 20000 27500 29000 27000 21500 18000
60 90 165 260 120 80 120 300 500 210 160 250 530 840 60 100 230 360 160 100 160 330 530 230 160 260 560
39 93 61 135 52 50 99 84 180 57 62 125 102 217 41 97 77 168 62 55 113 91 190 61 65 135 98 215
105 140 280 375 275 185 230 530 715 430 375 480 900 1220 105 140 380 515 355 245 315 565 760 465 390 500 940 1270
S 61807 C TA S 61807 E TA S 61907 C TA S 61907 E TA SM 61907 C TA KH 61907 C TA KH 61907 E TA S 6007 C TA S 6007 E TA SM 6007 C TA KH 6007 C TA KH 6007 E TA S 6207 C TA S 6207 E TA 40 mm S 61808 C TA S 61808 E TA S 61908 C TA S 61908 E TA SM 61908 C TA KH 61908 C TA KH 61908 E TA S 6008 C TA S 6008 E TA SM 6008 C TA KH 6008 C TA KH 6008 E TA S 6208 C TA S 6208 E TA 33
48.6 50.4 0.6 0.3 0.6 48.6 50.4 0.6 0.3 0.6 48.6 50.4 0.6 0.3 0.6 48.1 48.1 53.1 53.1 53.1 49.4 0.6 0.3 0.6 49.4 0.6 0.3 0.6 56.3 1.0 56.3 1.0 56.3 1.0 0.6 0.6 0.6 0.6 0.6 0.6 0.6 1.0 1.0 1.0 1.0 1.0 1.0 1.0 0.3 0.3
600 120 1000 245 420 320 500 1000 77 82 162 142
SM 6007 C TA KH 6007 C TA KH 6007 E TA S 6207 C TA S 6207 E TA 40 mm S 61808 C TA S 61808 E TA S 61908 C TA S 61908 E TA SM 61908 C TA KH 61908 C TA KH 61908 E TA S 6008 C TA S 6008 E TA
53.6 56.0 1.0 53.6 56.0 1.0 60.6 64.5 1.1 60.6 64.5 1.1 48.1 48.1 55.2 55.2 55.2 55.2 55.2
47.4 47.4 43.9 43.9 46.8 46.8 46.8 46.8 45.3 46.8 45.3 49.2 49.2 49.2 49.2 47.5 49.2 47.5 52.8 52.8
46.0 3.175 46.0 3.175 51.0 6.35 51.0 6.35 51.0 6.35 51.0 4.762 51.0 4.762 54.0 7.938 54.0 7.938 54.0 7.938 54.0 6.35 54.0 6.35 60.0 11.906 60.0 11.906
49.1 0.3 0.3 49.1 0.3 0.3 57.2 0.6 0.3 57.2 0.6 0.3 57.2 0.6 0.3 56.7 0.6 0.3 56.7 0.6 0.3
0.6 0.15 0.6 0.15 0.6 0.15 0.6 0.15 0.6 0.15 1.0 1.0 1.0 1.0 1.0 1.0 1.0 0.3 0.3 0.3 0.3 0.3 0.6 0.6
460 109 720 225 320 210 660 460 330 520 1100 83 75 130 83 88 175 137
59.0 61.8 1.0 0.6 59.0 61.8 1.0 0.6 59.0 61.8 1.0 0.6 60.2 62.6 1.0 0.6 60.2 62.6 1.0 0.6 67.6 67.6 71.8 71.8 1.1 1.1 0.6 0.6
142 900
1800 288
www.gmn.de
45 to 50 mm
Boundary dimensions Balls Dimensions Abutment dimensions Weight Contact Load rating Speed value Preload/axial rigidity angle Spring preload
d m
DW
d1
d2
D1
D2
r1,2
dT
0 15 25 17 17 25 15 25 15 17 25 15 25 15 25 17 17 25 15 25 15 17 25 15 25
C0
C0 HY
noil
ngrease
Fv
Cax
Fv
Cax
Fv
Cax
Ff
Designation 45 mm
45 45 45 45 45 45 45 45 45 45 45 45 50 50 50 50 50 50 50 50 50 50 50 50
68 68 68 68 68 75 75 75 75 75 85 85 72 72 72 72 72 80 80 80 80 80 90 90
12 12 12 12 12 16 16 16 16 16 19 19 12 12 12 12 12 16 16 16 16 16 20 20
20 20 20 28 28 18 18 18 22 22 14 14 21 21 21 30 30 19 19 19 25 25 15 15
60.7 62.7 0.6 0.3 60.7 62.7 0.6 0.3 60.7 62.7 0.6 0.3
0.6 0.6 0.6 0.6 0.6 1.0 1.0 1.0 1.0 1.0 1.0 1.0 0.6 0.6 0.6 0.6 0.6 1.0 1.0 1.0 1.0 1.0 1.0 1.0
0.15 0.15 0.15 0.15 0.15 0.3 0.3 0.3 0.3 0.3 0.6 0.6 0.15 0.15 0.15 0.15 0.15 0.3 0.3 0.3 0.3 0.3 0.6 0.6
50.0 50.0 50.0 50.0 50.0 51.0 51.0 51.0 51.0 51.0 53.0 53.0 55.0 55.0 55.0 55.0 55.0 56.0 56.0 56.0 56.0 56.0 58.0 58.0
63.5 63.5 63.5 63.5 63.5 69.0 69.0 69.0 69.0 69.0 77.0 77.0 67.5 67.5 67.5 67.5 67.5 74.0 74.0 74.0 74.0 74.0 82.0 82.0
54.5 54.5 54.5 53.8 53.8 57.6 57.6 57.6 56.9 56.9 61.7 61.7 58.9 58.9 58.9 58.3 58.3 62.5 62.5 62.5 61.9 61.9 66.7 66.7
0.128 0.128 0.128 0.128 0.128 0.238 0.238 0.238 0.238 0.238 0.416 0.416 0.129 0.129 0.129 0.129 0.129 0.256 0.256 0.256 0.256 0.256 0.486 0.486
15200 14300 10600 7300 6950 27000 26000 18500 10800 10300 45500 43500 15400 14500 10900 7500 7150 28000 26500 19000 11600 11100 47500 45000
13600 12900 6800 5150 4900 22600 21500 11400 6950 6650 33500 32500 14500 13700 7200 5550 5300 24300 23100 12300 8000 7600 37000 35500
9600 9100 4800 3600 3450 15900 15100 8000 4900 4700 23500 22600 10200 9700 5100 3900 3700 17100 16300 8600 5650 5350 26000 24700
30000 25500 35000 38000 34000 28000 24000 33000 36000 32000 26000 22500 28000 24000 33000 35000 32000 26000 22000 31000 33000 30000 24500 20500
22500 19000 26000 28500 25500 21000 18000 24500 27000 24000 19500 17000 21000 18000 24500 26000 24000 19500 16500 23000 24500 22500 18500 15500
80 120 55 35 60 130 210 90 55 90 230 370 80 120 55 40 60 140 220 100 60 90 240 380
49 115 42 40 86 60 140 44 44 92 71
230 360 160 110 170 400 650 275 160 260 700
79 173 64 61 124 105 220 69 65 135 119 257 81 180 67 64 132 110 72 74 150 125 271
390 520 365 265 335 690 950 560 390 490 1170 1580 395 530 375 270 340 715 970 570 415 530 1220 1640
S 61909 C TA S 61909 E TA SM 61909 C TA KH 61909 C TA KH 61909 E TA S 6009 C TA S 6009 E TA SM 6009 C TA KH 6009 C TA KH 6009 E TA S 6209 C TA S 6209 E TA 50 mm S 61910 C TA S 61910 E TA SM 61910 C TA KH 61910 C TA KH 61910 E TA S 6010 C TA S 6010 E TA SM 6010 C TA KH 6010 C TA KH 6010 E TA S 6210 C TA S 6210 E TA
720 232
50.8 60.7 62.2 0.6 0.3 50.8 60.7 62.2 0.6 0.3 65.0 68.6 1.0 0.6 65.0 68.6 1.0 0.6 65.0 68.6 1.0 0.6 65.6 67.8 65.6 67.8 72.5 72.5 65.2 65.2 65.2 77.5 77.5 1.0 0.6 1.0 0.6 1.1 1.1 0.6 0.6
60.0 8.731 60.0 8.731 60.0 8.731 60.0 6.35 60.0 6.35 65.0 12.7 65.0 12.7 61.0 6.35 61.0 6.35 61.0 6.35 61.0 4.762 61.0 4.762 65.0 8.731 65.0 8.731 65.0 8.731 65.0 6.35 65.0 6.35 70.0 12.7 70.0 12.7
1300 300
169 1100 50 119 44 44 90 64 145 47 49 100 75 230 370 170 110 180 420 290 180 280 720
2200 346 460 740 330 230 360 1330 580 350 1440 115 241 89 86 171 310 99 98 178
67.2 0.6 0.3 67.2 0.6 0.3 67.2 0.6 0.3 66.7 0.6 0.3 66.7 0.6 0.3
70.0 73.6 1.0 0.6 70.0 73.6 1.0 0.6 70.0 73.6 1.0 0.6 70.7 70.7 73.1 73.1 1.0 0.6 1.0 0.6 1.1 0.6 1.1 0.6
840 160
670 230
62.5 62.5
177 1140
34
35
www.gmn.de
55 to 60 mm
Boundary dimensions Balls Dimensions Abutment dimensions Weight Contact Load rating Speed value Preload/axial rigidity angle Spring preload
d m
DW
d1
d2
D1
D2
r1,2
dT
0 15 25 17 17 25 15 25 15 17 25 15 25 15 25 19 17 25 15 25 15 17 25 15 25
C0
C0 HY
noil
ngrease
Fv
Cax
Fv
Cax
Fv
Cax
Ff
Designation 55 mm
55 55 55 55 55 55 55 55 55 55
80 80 80 80 80 90 90 90 90 90
13 13 13 13 13 18 18 18 18 18 21 21 13 13 13 13 13 18 18 18 18 18 22 22
67.5 67.5 67.5 67.5 67.5 72.5 72.5 72.5 72.5 72.5
7.144 7.144 7.144 5.556 5.556 9.525 9.525 9.525 7.938 7.938
21 21 21 30 30 20 20 20 23 23 15 15 23 23 23 32 32 22 22 22 24 24 15 15
71.9 74.5 71.9 74.5 71.9 74.5 72.9 74.5 72.9 74.5 78.2 81.9 78.2 81.9 78.2 81.9
1.0 0.3 0.6 1.0 0.3 0.6 1.0 0.3 0.6 1.0 0.3 0.6 1.0 0.3 0.6 1.1 1.1 1.1 1.0 1.0 1.0 1.0 1.0 1.0 1.0 0.3 0.3 0.3 0.3 0.3 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.1 1.1 1.1 1.1 1.1 1.5 1.5 0.6 0.6 0.6 0.6 0.6 1.1 1.1 1.1 1.1 1.1 1.5 1.5
0.3 0.3 0.3 0.3 0.3 0.6 0.6 0.6 0.6 0.6 1.0 1.0 0.3 0.3 0.3 0.3 0.3 0.6 0.6 0.6 0.6 0.6 1.0 1.0
60.0 60.0 60.0 60.0 60.0 62.0 62.0 62.0 62.0 62.0 64.0 64.0 65.0 65.0 65.0 65.0 65.0 67.0 67.0 67.0 67.0 67.0 70.0 70.0
75.0 75.0 75.0 75.0 75.0 83.0 83.0 83.0 83.0 83.0 91.0 91.0 80.0 80.0 80.0 80.0 80.0 88.0 88.0 88.0 88.0 88.0 101.0 101.0
65.4 65.4 65.4 65.0 65.0 69.8 69.8 69.8 69.3 69.3 73.8 73.8 70.4 70.4 70.4 70.0 70.0 74.9 74.9 74.9 74.4 74.4 81.5 81.5
0.181 0.181 0.181 0.181 0.181 0.374 0.374 0.374 0.374 0.374 0.621 0.621 0.195 0.195 0.195 0.195 0.195 0.406 0.406 0.406 0.406 0.406 0.795 0.795
18400 17400 13600 10000 9600 32500 30500 23100 16700 15900 58000 55500 19200 18100 14100 10300 9800 34000 32000 24500 17000 16200 70000 66500
17100 16200 9400 7500 7150 29500 28000 15500 11400 10800 46000 44000 19000 17900 10300 8100 7700 32500 31000 17400 11900 11400 56500 54000
12100 11400 6600 5250 5050 20500 19400 10900 8000 7600 32500 31000 13300 12600 7200 5650 5400 22800 21600 12200 8400 8000 40000 38000
25000 21500 29500 31000 28500 23500 20000 27500 29500 26500 22000 18500 23500 20000 27500 29500 26500 22000 18500 26000 27500 25000 20000 17000
18500 16000 22000 23000 21500 17500 15000 20500 22000 20000 16500 14000 17500 15000 20500 22000 20000 16500 14000 19500 20500 18500 15000 12500
90 150 70 50 80 160 260 115 80 130 300 470 100 150 70 50 80 170 270 125 90 140 350 560
280 440 210 150 240 490 770 350 250 400
470 635 465 360 460 830 1110 695 600 760 1480
S 61911 C TA S 61911 E TA SM 61911 C TA KH 61911 C TA KH 61911 E TA S 6011 C TA S 6011 E TA SM 6011 C TA KH 6011 C TA KH 6011 E TA S 6211 C TA S 6211 E TA 60 mm S 61912 C TA S 61912 E TA SM 61912 C TA KH 61912 C TA KH 61912 E TA S 6012 C TA S 6012 E TA SM 6012 C TA KH 6012 C TA KH 6012 E TA S 6212 C TA S 6212 E TA
66.8 66.8 66.8 66.8 65.6 66.8 65.6 69.0 69.0 68.1 68.1 68.1 68.1 66.8 68.1 66.8 71.9 71.9 71.9 71.9 71.9 70.7 70.7
79.2 82.4 1.1 79.2 82.4 1.1 85.8 91.6 85.8 91.6 1.5 1.5
77.5 14.288 77.5 14.288 72.5 72.5 72.5 72.5 72.5 7.144 7.144 7.144 5.556 5.556
83 900
198 1400 300 58 137 61 52 109 75 180 56 59 122 300 220 160 240 515 810 375 260 400 94 93 80 161 124 274 83 87 177 146 333
2800 404 2020 600 430 132 122 490 660 540 370 470 870 1160 740 610 770 1790
76.9 79.5 1.0 76.9 79.5 1.0 76.9 79.5 1.0 77.9 79.5 1.0 77.9 79.5 1.0 83.2 87.0 1.1 83.2 87.0 1.1 83.2 87.0 1.1 84.2 87.4 1.1 84.2 87.4 1.1 95.5 101.4 1.5 95.5 101.4 1.5
460 208
920 276 310 104 490 209 1030 175 1620 364 750 120 510 2100 115 213 800 229
77.5 9.525 77.5 9.525 77.5 9.525 77.5 77.5 7.938 7.938
76.0 76.0
36
37
www.gmn.de
65 to 75 mm
Boundary dimensions Balls Dimensions Abutment dimensions Weight Contact Load rating Speed value Preload/axial rigidity angle Spring preload
d m
DW
d1
d2
D1
D2
r1,2
dT
0 15 25 19 17 25 15 25 15 17 25 15 25 15 25 19 17 25 15 25 15 17 25 15 25 19 15 25 17
C0
C0 HY
noil
ngrease
Fv
Cax
Fv
Cax
Fv
Cax
Ff
Designation 65 mm
65 65 65 65 65
90 90 90 90 90
13 13 13 13 13 18 18 18 18 18 23 23 16 16 16 16 16 20 20 20 20 20 16 16 16 20 20 20
24 24 24 34 34 23 23 23 25 25 16 16 24 24 24 32 32 21 21 21 24 24 25 25 25 22 22 22
81.9 84.5 1.0 0.3 81.9 84.5 1.0 0.3 81.9 84.5 1.0 0.3 82.9 84.5 1.0 0.3 82.9 84.5 1.0 0.3 88.2 92.0 88.2 92.0 88.2 92.0 89.2 92.4 89.2 92.4 1.1 1.1 1.1 1.1 1.1 1.5 1.5 1.0 1.0 1.0 1.0 1.0 1.1 1.1
0.6 0.6 0.6 0.6 0.6 1.1 1.1 1.1 1.1 1.1 1.5 1.5
0.3 0.3 0.3 0.3 0.3 0.6 0.6 0.6 0.6 0.6 1.1 1.1 0.3 0.3 0.3 0.3 0.3 0.6 0.6 0.6 0.6 0.6 0.3 0.3 0.3 0.6 0.6 0.6
70.0 70.0 70.0 70.0 70.0 72.0 72.0 72.0 72.0 72.0 75.0 75.0 76.0 76.0 76.0 76.0 76.0 77.0 77.0 77.0 77.0 77.0 81.0 81.0 81.0 82.0 82.0 82.0
85.0 85.0 85.0 85.0 85.0 93.0 93.0 93.0 93.0 93.0 110.0 110.0 94.5 94.5 94.5 94.5 94.5 102.0 102.0 102.0 102.0 102.0 99.5 99.5 99.5 107.0 107.0 107.0
75.4 75.4 75.4 75.0 75.0 79.9 79.9 79.9 79.3 79.3 88.3 88.3 82.6 82.6 82.6 82.3 82.3 86.6 86.6 86.6 85.7 85.7 87.5 87.5 87.5 91.7 91.7 91.7
0.207 0.207 0.207 0.207 0.207 0.431 0.431 0.431 0.431 0.431 1.008 1.008 0.346 0.346 0.346 0.346 0.346 0.593 0.593 0.593 0.593 0.593 0.35 0.35 0.35 0.64 0.64 0.64
19500 18300 14400 10600 10100 34500 32500 25000 17300 16500 72500 69000 24400 23000 17300 13000 12400 48500 46000 35500 23700 22700 29500 27500 20800 49500 47000 36000
20000 18900 10800 8600 8200 34500 32500 18400 12500 11900 61500 59000 26000 24500 13000 10600 10100 46000 43500 25500 17200 16400 31000 29500 16000 48500 46000 26500
14000 13300 7600 6050 5800 24100 22900 13000 8800 8400 43500 41500 18200 17300 9200 7400 7050 32500 30500 17800 12100 11500 21600 20500 11300 34000 32500 18700
22000 18500 26000 27500 25000 20500 17500 24000 26000 23500 18500 15500 20000 17000 23500 25000 22500 19000 16000 22000 24000 21500 19000 16000 22000 18000 15500 21000
16500 14000 19500 20500 18500 15500 13000 18000 19500 17500 14000 11500 15000 12500 17500 18500 17000 14000 12000 16500 18000 16000 14000 12000 16500 13500 11500 15500
100 160 75 55 80 175 275 130 90 140 370 590 130 200 90 65 100 240 180 120 190 150 230 110 250 400 180
300 470 220 160 250 525 825 380 260 410 1110
96 215 96 83 169 128 284 91 90 182 158 347 111 247 105 89 182 140 310 99 104 211 120 270 116 148 330 126
500 665 550 380 480 880 1180 760 620 790 1850 2550 625 840 660 465 590 1240 1670 1070 850 1080 760 1000 800 1270 1710 1230
S 61913 C TA S 61913 E TA SM 61913 C TA KH 61913 C TA KH 61913 E TA S 6013 C TA S 6013 E TA SM 6013 C TA KH 6013 C TA KH 6013 E TA S 6213 C TA S 6213 E TA 70 mm S 61914 C TA S 61914 E TA SM 61914 C TA KH 61914 C TA KH 61914 E TA S 6014 C TA S 6014 E TA SM 6014 C TA KH 6014 C TA KH 6014 E TA 75 mm S 61915 C TA S 61915 E TA SM 61915 C TA S 6015 C TA S 6015 E TA SM 6015 C TA 39
940 286
65 100 65 100 65 100 65 100 65 100 65 120 65 120 70 100 70 100 70 100 70 100 70 100 70 70 70 70 70 110 110 110 110 110
82.5 9.525 82.5 9.525 82.5 9.525 82.5 7.938 82.5 7.938 92.5 15.875 92.5 15.875 85 85 85 85 85 90 90 90 90 90 90 90 90 95 95 95 7.938 7.938 7.938 6.35 6.35 11.906 11.906 11.906 9.525 9.525 8.731 8.731 8.731 11.906 11.906 11.906
1650 376
800 235 2220 225 3520 462 740 530 390 156 139 118
82.8 102.3 108.5 82.8 102.3 108.5 80.1 80.1 80.1 80.1 80.1 78.5 78.5 89.9 92.7 89.9 92.7 89.9 92.7 91.3 93.4 91.3 93.4 97.4 101.7 97.4 101.7 97.4 101.7 96.7 100.8 96.7 100.8
228 1760 69 165 71 59 122 85 66 68 143 75 178 78 91 82 370 590 260 200 310 700 500 360 570 440 700 320 760 550
1.0 0.3 0.6 1.0 0.3 0.6 1.0 0.3 0.6 1.0 0.3 0.6 1.0 0.3 0.6 1.1 1.1 1.1 1.1 1.1 1.0 1.0 1.0 1.0 1.0 1.1 1.1 1.1 1.1 1.1 0.6 0.6 0.6 1.1 1.1 1.1
1180 329
620 235 1400 200 2400 420 1000 720 134 137
1150 274 890 169 1400 360 640 153 1510 208 2380 440 1100 167
95.3 98.8 0.6 0.3 95.3 98.8 0.6 0.3 95.3 98.8 0.6 0.3 102.2 107 102.2 107 102.2 107 1.1 1.1 1.1 0.6 0.6 0.6
SM 61915 C TA
219 1190
SM 6015 C TA
www.gmn.de
80 to 95 mm
Boundary dimensions Balls Dimensions Abutment dimensions Weight Contact Load rating Speed value Preload/axial rigidity angle Spring preload
Designation 80 mm S 61916 C TA S 61916 E TA S 6016 C TA S 6016 E TA 85 mm S 61917 C TA S 61917 E TA S 6017 C TA S 6017 E TA 90 mm S 61918 C TA S 61918 E TA S 6018 C TA S 6018 E TA 95 mm S 61919 C TA S 61919 E TA S 6019 C TA S 6019 E TA
d m
DW
d1
d2
D1
D2
r1,2
dT
0 15 25 19 15 25 17 15 25 19 15 25 17 15 25 19 15 25 17 15 25 19 15 25 17
C0
C0 HY
noil
ngrease
Fv
Cax
Fv
Cax
Fv
Cax
Ff
Designation 80 mm
80 80 80 80 80 80
16 16 16
95 95 95
25 25 25
89.4 89.4 89.4 94.3 94.3 94.3 96.2 96.2 96.2 99.3 99.3 99.3 101.2 101.2 101.2 105.8 105.8 105.8
100.8 104.6 0.6 0.3 100.8 104.6 0.6 0.3 100.8 104.6 0.6 0.3 110.7 116.1 110.7 116.1 110.7 116.1 1.1 1.1 1.1 0.6 0.6 0.6
104 104 104 117 117 117 114 114 114 122 122 122 119 119 119 131 131 131 124 124 124 136 136 136
92.4 92.4 92.4 98.7 98.7 98.7 99.5 99.5 99.5 103.7 103.7 103.7 104.5 104.5 104.5 110.7 110.7 110.7 109.5 109.5 109.5 115.7 115.7 115.7
0.37 0.37 0.37 0.84 0.84 0.84 0.54 0.54 0.54 0.89 0.89 0.89 0.56 0.56 0.56 1.15 1.15 1.15 0.59 0.59 0.59 1.20 1.20 1.20
35500 33500 25500 60000 57500 43000 40000 37500 29500 61500 59000 44000 40500 38500 30000 74500 70500 52000 41000 39000 30500 77000 72000 53500
38500 36500 20100 58000 56500 31000 43000 40500 23200 61500 60000 32500 45000 42500 24200 74000 70000 38500 47000 44500 25500 79000 74500 41000
27000 25500 14200 41000 40000 21600 30500 28500 16300 43500 42000 22900 31500 30000 17000 52000 49500 27000 33000 31500 17800 55000 52500 28500
18000 15500 21000 16500 14000 19500 16500 14000 19500 16000 13500 18500 16000 13500 18500 15000 12500 17500 15000 13000 18000 14000 12000 16500
13500 11500 15500 12500 10500 14500 12500 10500 14500 12000 10000 14000 12000 10000 14000 11000 9400 13000 11000 9800 13500 10500 9000 12500
180 280 130 310 490 220 200 320 150 310 500 220 210 320 150 380 600 270 210 330 150 390 610 270
540 840 390 920 650 610 440 940 670 620 970 450
136 305 133 159 131 142 320 140 165 137 146 330 145 179 146 150 335 150 186 415 152
1080 780
192 175
S 61916 C TA S 61916 E TA SM 61916 C TA S 6016 C TA S 6016 E TA SM 6016 C TA 85 mm S 61917 C TA S 61917 E TA SM 61917 C TA S 6017 C TA S 6017 E TA SM 6017 C TA 90 mm S 61918 C TA S 61918 E TA SM 61918 C TA S 6018 C TA S 6018 E TA SM 6018 C TA 95 mm S 61919 C TA S 61919 E TA SM 61919 C TA S 6019 C TA S 6019 E TA SM 6019 C TA
SM 61916 C TA
22 102.5 13.494 20 22 102.5 13.494 20 22 102.5 13.494 20 18 102.5 10.319 18 102.5 10.319 18 102.5 10.319 22 22 22 18 18 18 24 24 24 107.5 13.494 107.5 13.494 107.5 13.494 107.5 10.319 107.5 10.319 107.5 10.319 115 115 115 15.081 15.081 15.081 25 25 25 21 21 21 26 26 26 20 20 20
SM 6016 C TA
108.8 112.9 0.6 0.6 0.6 0.6 108.8 112.9 0.6 0.6 0.6 0.6 108.8 112.9 0.6 0.6 0.6 0.6 115.7 121.1 115.7 121.1 115.7 121.1 1.1 1.1 1.1 0.6 0.6 0.6 1.1 1.1 1.1 0.6 0.6 0.6
1220 198 1020 1910 420 1360 890 185 1130 1570 2140 1500 1040 1400 1140 1900 1770 1050 1420 1160 1970 1820 1880 233 1340 182
210 960
SM 61917 C TA
245 1500
SM 6017 C TA
113.8 117.9 0.6 0.6 0.6 0.6 113.8 117.9 0.6 0.6 0.6 0.6 113.8 117.9 0.6 0.6 0.6 0.6 124.2 130.1 124.2 130.1 124.2 130.1 1.5 1.5 1.5 0.6 0.6 0.6 1.5 1.5 1.5 0.6 0.6 0.6
SM 61918 C TA
525 2600
SM 6018 C TA
1590 194 1250 209 1970 445 920 196 2330 265 1640 202
18 112.5 10.319 18 112.5 10.319 18 112.5 10.319 24 120 24 120 24 120 15.081 15.081 15.081
118.8 122.9 0.6 0.6 0.6 0.6 118.8 122.9 0.6 0.6 0.6 0.6 118.8 122.9 0.6 0.6 0.6 0.6 129.2 135.1 129.2 135.1 129.2 135.1 1.5 0.6 1.5 0.6 1.5 0.6 1.5 1.5 1.5 0.6 0.6 0.6
SM 61919 C TA
SM 6019 C TA
40
41
www.gmn.de
100 to 120 mm
Boundary dimensions Balls Dimensions Abutment dimensions Weight Contact Load rating Speed value Preload/axial rigidity angle Spring preload
Designation 100 mm S 61920 C TA S 61920 E TA SM 61920 C TA S 6020 C TA S 6020 E TA 105 mm S 61921 C TA S 61921 E TA S 6021 C TA S 6021 E TA 110 mm S 61922 C TA S 61922 E TA S 6022 C TA S 6022 E TA 120 mm S 61924 C TA S 61924 E TA SM 61924 C TA S 6024 C TA S 6024 E TA SM 61922 C TA
d m
DW
d1
d2
D1
D2
r1,2
dT
0 15 25 19 15 25 17 15 25 19 15 25 17 15 25 19 15 25 17 15 25 19 15 25 17
C0
C0 HY
noil
ngrease
Fv
Cax
Fv
Cax
Fv
Cax
Ff
Designation 100 mm
100 140 100 140 100 140 100 150 100 150 100 150 105 145 105 145 105 145 105 160 105 160 105 160 110 150 110 150 110 150 110 170 110 170 110 170 120 165 120 165 120 165 120 180 120 180 120 180
25 25 25 22 22 22 26 26 26 22 22 22 27 27 27
112.8 112.8 112.8 115.8 115.8 115.8 117.8 117.8 117.8 122.8 122.8 122.8 122.8 122.8 122.8
127.2 132.0 0.6 0.6 0.6 0.6 127.2 132.0 0.6 0.6 0.6 0.6 127.2 132.0 0.6 0.6 0.6 0.6 134.2 140.1 134.2 140.1 134.2 140.1 1.5 1.5 1.5 0.6 0.6 0.6 1.5 1.5 1.5 0.6 0.6 0.6
107 107 107 110 110 110 112 112 112 116 116 116 117 117 117 121 121 121 128 128 128 131 131 131
133 133 133 141 141 141 138 138 138 150 150 150 143 143 143 159 159 159 157 157 157 169 169 169
116.5 116.5 116.5 120.7 120.7 120.7 121.5 121.5 121.5 127.9 127.9 127.9 126.5 126.5 126.5 135.0 135.0 135.0 138.5 138.5 138.5 145.0 145.0 145.0
0.80 0.80 0.80 1.25 1.25 1.25 0.83 0.83 0.83 1.59 1.59 1.59 0.86 0.86 0.86 1.98 1.98 1.98 1.18 1.18 1.18 2.13 2.13 2.13
51500 48500 37500 78000 74000 55000 52500 49500 38500 86000 81000 60500 53500 50000 39000
57000 54000 31000 83000 79000 43000 60000 56500 32500 92000 87000 48000 62500 59000 34000
40500 38000 21700 58000 55000 30500 42000 40000 22700 64500 61500 34000 44000 41500 23700 73500 70000 39000 56000 53000 30500 82000 78000 43000
14000 12000 16500 13500 11500 16000 13500 11500 16000 13000 11000 15000 13000 11000 15500 12000 10500 14500 12000 10000 14000 11500 9700 13500
10500 9000 12500 10000 8600 12000 10000 8600 12000 9800 8200 11000 9800 8200 11500 9000 7900 11000 9000 7500 10500 8600 7300 10000
260 410 190 400 630 280 270 420 200 440 690 310 270 420 200 500 790 360 340 540 250 530 830 380
100 107
790 570
162 365 160 193 158 166 375 166 203 450 166 170 385 171 212 470 174
S 61920 C TA S 61920 E TA SM 61920 C TA S 6020 C TA S 6020 E TA SM 6020 C TA 105 mm S 61921 C TA S 61921 E TA SM 61921 C TA S 6021 C TA S 6021 E TA SM 6021 C TA 110 mm S 61922 C TA S 61922 E TA SM 61922 C TA S 6022 C TA S 6022 E TA SM 6022 C TA 120 mm S 61924 C TA S 61924 E TA SM 61924 C TA S 6024 C TA S 6024 E TA SM 6024 C TA
3750 570 2700 1680 210 1600 232 2510 495 1170 218
SM 6020 C TA
132.2 137.0 0.6 0.6 0.6 0.6 132.2 137.0 0.6 0.6 0.6 0.6 132.2 137.0 0.6 0.6 0.6 0.6 142.2 148.4 2.0 142.2 148.4 2.0 142.2 148.4 2.0 1.0 1.0 1.0 2.0 2.0 2.0 1.0 1.0 1.0
103 800 248 1250 112 590 125 1310 300 2060 109 106 930 810
SM 61921 C TA
132.5 15.875 132.5 15.875 132.5 15.875 11.906 11.906 11.906 17.462 17.462 17.462
2610 285 2200 4120 595 2950 1850 221 2060 1370 1820 1490 2550 3450
SM 6021 C TA
137.2 142.0 0.6 0.6 0.6 0.6 137.2 142.0 0.6 0.6 0.6 0.6 137.2 142.0 0.6 0.6 0.6 0.6 150.6 157.5 2.0 150.6 157.5 2.0 150.6 157.5 2.0 1.0 2.0 1.0 2.0 1.0 2.0 1.0 1.0 1.0
1620 238 2550 510 1190 224 3020 300 4760 625
255 1270 114 600 130 1510 310 2380 115 1070 120 1030 129 750
99000 105000 94000 100000 70000 67500 64000 49500 104000 98000 74000 55000 80000 76000 43500 116000 110000 61000
SM 6022 C TA
22 142.5 13.494 22 142.5 13.494 22 142.5 13.494 28 150 28 150 28 150 17.462 17.462 17.462
150.7 156.0 0.6 0.6 0.6 0.6 150.7 156.0 0.6 0.6 0.6 0.6 150.7 156.0 0.6 0.6 0.6 0.6 160.6 167.5 2.0 160.6 167.5 2.0 160.6 167.5 2.0 1.0 1.0 1.0 2.0 2.0 2.0 1.0 1.0 1.0
3250 580
SM 6024 C TA
42
43
www.gmn.de
SNR
71900 : 71924 CH 71924 7000 : 7024 CH 7024 7200 : 7213 CH 7213 -
* Optimized inner geometry for increased speed. Outer diameters correspond to the given ISO group. Designations include only the basic types (not design details like contact angle, precision, matching, preload, etc.)
44
45
www.gmn.de
Series Z
Version with one shield (lubricated)
Series 2Z
Version with two shields (lubricated)
Material Bearing steel (chrome steel) 100 Cr 6 Material no. 1.3505, SAE 52100, SUJ2 Special steels on request Permissible operating temperature Heat treated for continuous operating temperatures up to 150C Hardness 60 to 64 HRC, fully hardened; corresponds to 700800 HV30
Material Ceramic (silicon nitride Si3N4) Material characteristics Low chemical afnity to 100 Cr 6 Low friction coefcient Low heat conductivity Corrosion resistance Non magnetic Electrically insulating 100% 75% 50%
Ceramic Si3N4
Series X2Z
Extra-wide bearing with 2 shields(lubricated) Reference speed coefcient: 1.0 106 mm/min
25% 0% 46
Density E-modulus
Expansion coefcient
47
www.gmn.de
Materials Cages
GMN high precision deep groove ball bearings are basically equipped with a steel cage (J cage). Depending on specic requirements (e.g. high speeds), cages made of other materials are available.
Clearance
The distance by which one bearing ring can be displaced relative to the other without measurable loading is dened as clearance. Axial clearance: displacement in the axial direction Radial clearance: displacement in the radial direction
J cage
T9H cage
TBH cage
TA, TB cages
Radial clearance Axial clearance
Material Sheet steel Permissible operating temperature 220C Fabrication two piece, tab-clamped or riveted
Material Material Polyamide (berglass reinforced) Laminated phenolic resin Permissible operating temperature 140C Fabrication single piece, crown cage Permissible operating temperature 120 C Fabrication single piece, crown cage
GMN Deep groove ball bearings: Radial clearance (per DIN 620/Part 4) Material Laminated phenolic resin Permissible operating temperature 120C Fabrication two piece, riveted Bore diameter d [mm] min 2 2 3 5 5 6 Radial clearance [m] max 13 13 18 20 20 20 min 8 8 11 13 13 15 C3 max 23 23 25 28 28 33 min 14 18 20 23 28 C4 max 29 33 36 41 46
CN
Deep groove ball bearings without a clearance specication are fabricated to CN specication (standard clearance).
48
49
www.gmn.de
Bearing designation
Example
Material - HY 6001 Bearings made of bearing steel have no designation Balls and rings made of different materials (HYBRID bearings) Designation of dimension series and bore diameter Extra-wide bearing Shield on one side, fastened with snap ring Shields on both sides, fastened with snap rings Shields are on the outer faces of bearing pairs Sheet steel cage Crown cage of berglass reinforced polyamide, ball-guided Crown cage of laminated phenolic resin, inner land guided Solid cage of laminated phenolic resin, outer land guided Solid cage of laminated phenolic resin, inner land guided Solid cage of brass, outer land guided Tolerance class P4 Tolerance class P2 ABEC 7 per ABMA standards, corresponds to P4 ABEC 9 per ABMA standards, corresponds to P2 GMN high precision per GMN specication GMN ultra precision per GMN specication Radial clearance smaller than standard Standard clearance (no designation) Radial clearance greater than standard Radial clearance greater than C3 Reduced radial clearance values are stated in plain text (values without measurable load) Marks the highest point of radial runout (the greatest wall thickness) for inner and outer ring like R, but only for inner ring like R, but only for outer ring X arrangement O arrangement Tandem arrangement ungreased Lubricant identier, e.g. Klber Asonic GLY 32
HY
Bearing size
6001
X J P4 C2 R D F G LY3
50 12
51
www.gmn.de
r1
D1
r1
r2
d1
dm
D1
r1
r2
d1
dm
Da
ra
da
Boundary dimensions d D B Balls d m D W Z [mm] [mm] pieces Pitch circle diameter Ball diameter Number of balls [mm] [mm] [mm] Bore diameter Outer diameter Width of single bearing
Dimensions d 1 D 1 r1, 2 [mm] [mm] [mm] Outer diameter of inner ring Inner diameter of outer ring Chamfer (min)
[kg]
Bearing weight
Load ratings C C 0 C0 HY [N] [N] [N] Dynamic load rating Static load rating, steel balls Static load rating, Si3N4 balls Speed with grease lubrication and sheet steel cage
Speed value
Abutment dimensions ra max [mm] Undercut of associated component Abutment diameter inner ring Abutment diameter outer ring da min [mm] Da max [mm]
ngrease [1/min]
dm
DW
d1
D1
r1,2
ra max
damin
Da max
C 0
C0 HY
ngrease
Designation 5 mm
5 6 7 7 8 8
16 19 19 22 22 22
5 6 6 7 7 10,312
6 8 8 7 7 7
www.gmn.de
9 to 40 mm
Boundary dimensions Balls Dimensions Abutment dimensions Weight Load rating Speed value
Designation 9 mm 609 629 10 mm 6000 6200 12 mm 6001 6001 X - 2Z 6201 15 mm 6002 6202 17 mm 6003 6203 20 mm 6004 6204 25 mm 6005 6205 30 mm 6006 6206 35 mm 6207 40 mm 6208
dm
DW
d1
D1
r1,2
ra max
damin
Da max
C0
C0 HY
ngrease
Designation 9 mm
9 9 10 10 12 12 12 15 15 17 17 20 20 25 25 30 30 35 40
24 26 26 30 28 28 32 32 35 35 40 42 47 47 52 55 62 72 80
7 8 8 9 8 11.506 10 9 11 10 12 12 14 12 15 13 16 17 18
16.7 18.0 18.0 20.0 20.0 20.0 22.0 23.5 25.3 26.0 28.5 31.0 33.5 36.0 39.1 42.5 46.0 53.5 60.0
3.969 4.762 4.762 5.556 4.762 4.762 5.953 4.762 5.953 4.762 6.747 6.350 7.938 6.350 7.938 7.144 9.525 11.112 11.906
8 7 7 7 8 8 7 9 8 10 8 9 8 10 9 11 9 9 9
13.45 14.65 14.65 16.00 16.65 15.00 18.30 20.15 21.10 22.65 24.10 26.60 28.50 32.20 34.04 38.10 40.40 47.40 52.80
19.90 21.40 21.40 24.45 23.40 25.10 26.00 26.90 29.00 29.40 32.95 35.45 38.55 40.05 44.05 46.95 52.05 60.50 67.60
0.3 0.3 0.3 0.6 0.3 0.3 0.6 0.3 0.6 0.3 0.6 0.6 1.0 0.6 1.0 1.0 1.0 1.0 1.0
0.3 0.3 0.3 0.6 0.3 0.3 0.6 0.3 0.6 0.3 0.6 0.6 1.0 0.6 1.0 1.0 1.0 1.0 1.0
11.5 13.0 12.5 14.5 14.5 14.5 16.5 17.5 19.5 20.0 21.5 25.0 26.0 30.0 31.0 36.0 36.0 43.0 48.0
21.0 23.0 23.0 25.5 25.0 25.0 27.5 29.0 30.5 31.5 35.0 37.0 41.0 42.0 46.0 49.0 55.0 64.0 72.0
0.023 0.020 0.019 0.032 0.022 0.027 0.037 0.030 0.045 0.039 0.065 0.069 0.106 0.080 0.128 0.128 0.199 0.315 0.402
3300 4350 4350 6000 4850 4850 6650 5300 7400 5700 9400 9800 13900 10400 15200 13200 20000 28000 29500
1390 1850 1850 2650 2210 2210 2950 2650 3600 3050 4700 5350 7400 6250 8900 8400 11800 17200 18000
980 1300 1300 1850 1560 1560 2070 1860 2550 2130 3300 3800 5200 4400 6250 5850 8300 12100 12700
37000 35000 34500 31000 31000 31000 28000 26500 25000 24000 22000 20000 18000 17000 16000 14500 13500 11500 10000
609 629 10 mm 6000 6200 12 mm 6001 6001 X - 2Z 6201 15 mm 6002 6202 17 mm 6003 6203 20 mm 6004 6204 25 mm 6005 6205 30 mm 6006 6206 35 mm 6207 40 mm 6208
54
55
www.gmn.de
Bearing selection
On the basis of GMN's comprehensive array of products, the specic performance proles of individual bearing designs can be used to select just the right bearing to meet a given set of requirements.
1.
Engineering
2.
Requirements prole Installed location: drawing, space available, bearing arrangement (fixed/ oating bearing) Application prole: precision, rigidity, operating temperature, load capacity, speed, service life, duty cycle
GMN high precision bearings provide intelligent bearing solutions for peak performance machine components. The outstanding characteristics of GMN ball bearings are the result of technically sophisticated quality features that attain maximum power limits. The values stated in the bearing data indicate the performance potential of the individual bearing depending on characteristic design and material properties. Inuences due to operating conditions can affect specic bearing characteristics and cause deviations from the stated bearing data. There are various measures which can be taken to counteract performance restrictions and improve bearing performance. Bearing selection Preloading Accuracy of associated components Lubrication Operating conditions
3.
Bearing selection Bearing design (materials, bearing type, series, bearing size, cage) Precision, contact angle, preload (rigid or with spring) Installation drawing, fastening, surrounding parts (ts, abutment dimensions)
4.
Lubrication Lubrication: Plan for supply/disposal, quantities/cycles, nozzles or bore holes in outer ring Grease lubrication: type of grease (viscosity, ndm factor), grease quantity, grease resupply system if required
5.
Calculation/verication Operational bearing loads (radial/axial loads) Permissible static load Speed limits Assessment of extended service life Assessment of grease consumption period
6.
Installation Associated components: shaft, housing, connecting parts; Tightening force and torque for bearing fastener Grease distribution run, re-lubrication or oil supply; noise Monitoring running smoothness, Checks of preload force, rigidity
56
57
www.gmn.de
Bearing selection
GMN standard series (characteristics)
from GMN series/bearing sizes to Characteristics ISO Applications
GMN series S (standard) S 61800 d=10 mm S 61808 d=40 mm 18 Very thin-walled, very compact size, very smooth (starting) running, high-speed suitability, limited load capacity Thin-walled, compact size, very smooth (starting) running, high-speed suitability, medium load capacity, smooth (starting) running, good ratio to load capacity and speed Thick-walled, very high load capacity, limited speed suitability
e.g. instrumentation
S 619/5 d=5 mm
S 61924 d=120 mm
19
General purpose, e.g. precision precision tools, tool making machine spindles with moderate loads General purpose, e.g. precision tools, tool making machine spindles with large loads aircraft generators/starters, tool making machine spindles, high load capacity, limited speed
S 605 d=5 mm
S 6024 d=120 mm
10
S 625 d=5 mm
S 6213 d=65 mm
02
60% 40%
Speed
GMN series SM (high speed) SM 61900 d=10 mm SM 61924 d=120 mm 19 Speed suitability about 20 % higher, less load capacity*, good compensation for temperature differences between inner and outer rings Speed suitability about 20 % higher, less load capacity*, good compensation for temperature differences between inner and outer rings
High speed precision tools, tool making machine spindles, moderate load capacity High frequency (HF) spindles for grinding and milling
20% 0%
S 6005 C
S 6005 E
SM 6005 C
KH 6005 C
KH 6005 E
S 6005 C
SM 6005 C
KH 6005 C
KH 6005 E
SM 605 d=10 mm
SM 6024 d=120 mm
10
GMN series KH (highest speed) KH 61900 d=10 mm KH 61914 d=70 mm 19 Speed suitability about 25 % higher, less load capacity*, with seal and lifetime lubrication or open for oil lubrication Speed suitability about 25 % higher, less load capacity*, with seal and lifetime lubrication or open for oil lubrication
*(in comparison to GMN series S) Spindles for woodworking, bearing covered
KH 6000 d=10 mm 58
KH 6014 d=70 mm
10
Ultra high frequency spindles for grinding, open bearing, Oil lubrication
59
www.gmn.de
Preload
Preload is dened as a continuously acting axial force exerted on a ball bearing which produces elastic deformation in the contact area of balls and raceways. The installation of ball bearings with rigid or with spring preload optimizes numerous performance characteristics for bearing operation. Reduced spring action establishes denable radial and axial rigidity (see diagram) High running accuracy/processing accuracy even under changing load conditions Reduced vibrations and running noise Prevention of slippage and mixed friction for rolling element contact at high speeds and high acceleration Reduced amounts of sliding friction at high speeds (reduced contact angle change between inner and outer ring) Increase of load capacity (by external loads and speeds) with longer service life Line of ux
Spring preloading
Structural features: Bearing 1 (work side) is axially xed in the housing Bearing 2 is axially oating (xed seating position of the inner ring on the shaft) The spring force on the outer ring of bearing 2 produces a constant preload on both bearings. The required spring preload is adjusted via the spring travel (travel-force function corresponding to the spring characteristic) To achieve perfect preload results, sufcient axial freedom of motion is required for the oating bearing's outer ring The positioning spring is adjusted in the effective direction of the external axial load If single bearings are employed: < ~> , these bearings can be unmatched Clearance If a tandem bearing arrangement is employed, ( << ~>> ) matched bearings ( L, M or S ) ensure uniform load distribution Characteristics: The preload results independent of speed and temperature exclusively from spring force The spring force exerts a constant preload on the bearing and counter bearing Thermal expansion of the shaft and housing have no inuence on preload Spring preloaded bearing systems permit the greatest speeds
Bearing 1
Bearing 2
Rigidity
Rigidity is dened as the magnitude of axial force [N] on a ball bearing which causes the bearing's rings to be displaced toward one another by 1 m. Appropriate preload increases bearing rigidity and supports the bearing's loading capacity against applied forces. Preload, rigidity
Rigidity C [N/m] 200 180 160 140 120 100 80 60 40 20 0 0 50 100 150 200 250 300 350 Cax : = 25 Cax : = 15 400 450 500 Preload FV [N] Crad : = 15 Crad : = 25
Lift-off force
The force at which a bearing becomes free of load by an axial load acting centrally on a bearing set is dened as lift-off force. If the external axial load exceeds the lift-off force ... balls and raceways of the relieved ball bearing are no longer in permanent contact ... wear increases due to increased sliding friction
60
61
www.gmn.de
Preload
Rigid preload: Single bearings
Structural features: Bearing 1 (work side) and bearing 2 have axially and radially xed positions (inner rings sit rmly on the shaft and outer rings in the housing) The contact surfaces of associated components to the inner and outer ring have equal length and are plane parallel To achieve the predened preload, it is necessary for the respective bearings to be matched Bearing 1 Bearing 2 Characteristics: Substantially increased axial and radial rigidity (in comparison to spring preload) As friction heat increases as a consequence of increased speed, preload increases to reduce maximum speed (in comparison to spring preload) The theoretical maximum speed can be calculated on the basis of speed correction factors Temperature differences between shaft (inner ring) and housing (outer ring) lead to preload changes due to thermal expansion If the shaft's temperature is higher than that of the housing, the bearing's radial clearance decreases Very high temperature differences and small contact angles can cause radial tension With small bearing spacing, a temperature gradient from shaft to housing causes an increase of preload With large bearing spacing, a temperature gradient from shaft to housing causes a decrease of preload The change of preload under operating conditions must be considered in the design GMN provides software solutions to perform the complex calculation for required bearing preload; these programs embody many years of practical experience which lead to reliable preload results. Bearing arrangement < > or > < << > << >> <<< > DB, DF TBT QBC QBT Effective Nominal preload FV [N] FV 1.35 FV 2 FV 1.6 FV Axial rigidity Cax* [N/m] Cax 1.45 Cax 2 Cax 1.8 Cax Lift-off force Fa max [N] 5.65 FV 5.65 FV 8.5 FV 2.85 FV
Rigidity and lift-off force Radial rigidity for all arrangements: at = 15: Crad ~ 6 Cax at = 25: Crad ~ 2 Cax
* Reference values for bearing pairs in O or X arrangement (see bearing data). Inuences due to operating conditions (e.g. speed, load) are not taken into account.
62
63
www.gmn.de
Bearing arrangements
Bearing pairs
(multiple arrangements with 2 bearings) For rigid bearing preload, matched bearing pairs in O, X or tandem arrangement provide an effective economic and technical solution to a large number of applications.
Bearing sets
(multiple arrangements with 3 or more bearings) Where there are maximum demands on system rigidity or high loading, the X, O or Tandem arrangements with 3 or more bearings are able to attain outstanding performance characteristics.
O arrangement (DB)
Pressure lines diverge in the direction of the bearing's axis Wide support base (H) and high rigidity against tilting moments Axial force absorption in both directions H
X arrangement (DF)
Pressure lines converge in the direction of the bearing's axis Insensitive to misalignment Reduced support base size and tilt rigidity Axial force absorption in both directions H
64
65
www.gmn.de
Spacers
Distinct optimization of individual quality features with paired bearings can be achieved by the installation of spacers. The width of the spacer must be at least as wide as a single bearing. Spacer width
B Characteristics:
>B
Enlarge the support base (H) and increase radial rigidity Optimize thermal dissipation Improve bearing lubrication by optimized oil ow Change of preload with matched bearings is possible If the width of the shaft spacer is smaller than the width of the housing spacer then preload will be increased with the O arrangement preload will be decreased with X arrangement For bearing sets with spacers (e.g. <||<||>||>), only the spacer between different pressure line courses must be ground off
Matching accuracy
General matching The general matching accuracy of 2 m provides for uniform load absorption and a constant operating temperature in multiple arrangements. Mated matching A highly precise matching accuracy of 1 m (on request) increases the speed suitability of mated matched bearing pairs/sets even further. Sufx for order designation: X-opt., O-opt. or T-opt.
Structural features: Material: 100 Cr6, or other, hardened (>=45 HRC) The required plane parallelism of outer and inner spacer is guaranteed by surface grinding both rings in one clamping operation Detailed information on the difference dimension of spacer rings: www.gmn.de 66
67
www.gmn.de
Comparison of international tolerance standards (tolerance symbols per DIN ISO 1132-1) Outer ring D over Nominal outside diameter [mm] including
80 120
0 / -8.0 0 / -5.0 0 / -8.0 0 / -5.0 8.0 5.0 6.0 5.0 4.0 2.5 5.0 2.5 5.0 2.5 5.0 2.5 0 / -200 0 / -200 0 / -380 0 / -380 4.0 2.5
150 180
0 / -10.0 0 / -7.0 0 / -10.0 0 / -7.0 10.0 7.0 8.0 7.0 5.0 3.5 8.0 5.0 5.0 2.5 8.0 5.0
Inner ring tolerances (dimensions in m) P4 0 / -4.0 0 / -4.0 0 / -5.0 0 / -6.0 dmp HG 0 / -3.0 0 / -3.0 0 / -3.0 0 / -5.0 Deviation of mean bore diameter UP 0 / -3.0 0 / -3.0 0 / -3.0 0 / -3.0 in one plane P2 0 / -2.5 0 / -2.5 0 / -2.5 0 / -2.5 ds bearing series 60, 62 Difference between a single bore diameter and the nominal value of the bore Vdp max bearing series ... 618, 619 Difference between largest and smallest bore diameter in one plane out of roundness Vdp max bearing series 60, 62 Difference between largest and smallest bore diameter in one plane out of roundness Vdmp max Difference between largest and smallest mean bore diameter in different planes conicity Kia max True running of the inner ring in the assembled bearing radial runout P4 HG UP P2 P4 HG UP P2 P4 HG UP P2 P4 HG UP P2 P4 HG UP P2 0 / -4.0 0 / -3.0 0 / -3.0 0 / -2.5 4.0 3.0 3.0 2.5 3.0 3.0 3.0 2.5 2.0 2.0 2.0 1.5 2.5 2.0 1.5 1.5 3.0 3.0 2.0 1.5 3.0 3.0 2.0 1.5 0 / -40 0 / -40 0 / -25 0 / -40 0 / -250 0 / -250 0 / -250 0 / -250 2.0 2.0 1.5 0 / -4.0 0 / -3.0 0 / -3.0 0 / -2.5 4.0 3.0 3.0 2.5 3.0 3.0 3.0 2.5 2.0 2.0 2.0 1.5 2.5 2.0 1.5 1.5 3.0 3.0 2.0 1.5 3.0 3.0 2.0 1.5 0 / - 80 0 / - 80 0 / - 80 0 / - 80 0 / -250 0 / -250 0 / -250 0 / -250 2.0 2.0 1.5 0 / -5.0 0 / -3.0 0 / -3.0 0 / -2.5 5.0 3.0 3.0 2.5 4.0 3.0 3.0 2.5 2.5 2.0 2.0 1.5 3.0 2.0 1.5 2.5 4.0 3.0 2.0 1.5 4.0 4.0 2.5 2.5 0 / -120 0 / -120 0 / -120 0 / -120 0 / -250 0 / -250 0 / -250 0 / -250 2.5 2.0 2.0 1.5 0 / -6.0 0 / -5.0 0 / -3.0 0 / -2.5 6.0 5.0 3.0 2.5 5.0 5.0 3.0 2.5 3.0 3.0 2.0 1.5 4.0 2.0 2.0 2.5 4.0 4.0 2.0 1.5 4.0 4.0 2.5 2.5 0 / -120 0 / -120 0 / -120 0 / -120 0 / -250 0 / -250 0 / -250 0 / -250 3.0 2.0 2.0 1.5
Outer ring tolerances (dimensions in m) P4 0 / -4.0 0 / -5.0 0 / -6.0 0 / -7.0 0 / -8.0 Dmp HG 0 / -3.0 0 / -3.0 0 / -3.0 0 / -4.0 0 / -4.0 Deviation of mean outside diameter UP 0 / -3.0 0 / -3.0 0 / -3.0 0 / -4.0 0 / -4.0 in one plane P2 0 / -2.5 0 / -4.0 0 / -4.0 0 / -4.0 0 / -5.0 Ds bearing series 60, 62 Difference between a single outside diameter and nominal value VDp max bearing series 618, 619 Difference between largest and smallest outside diameter in one plane out of roundness VDp max bearing series 60, 62 Difference between largest and smallest outside diameter in one plane out of roundness VDmp max Difference between largest and smallest mean outside diameter in different planes conicity Kea max True running of the outer ring in the assembled bearing radial runout SD max Variation of generatrix gradient with respect to the reference face surface side runout Sea max Plane running of the face side with respect to the raceway, in the assembled bearing axial runout CS single bearing Deviation of a single outer ring width from nominal dimension width tolerance CS paired bearing Deviation of a single outer ring width from nominal dimension width tolerance VCS max Variation of outer ring width width variation P4 HG UP P2 P4 HG UP P2 P4 HG UP P2 P4 HG UP P2 P4 HG UP P2 P4 HG UP P2 P4 HG UP P2 0 / -4.0 0 / -3.0 0 / -3.0 0 / -2.5 4.0 2.0 2.0 2.5 3.0 2.0 2.0 2.5 2.0 1.0 1.0 1.5 3.0 2.0 2.0 1.5 4.0 4.0 2.0 1.5 5.0 5.0 2.0 1.5 0 / -5.0 0 / -3.0 0 / -3.0 0 / -4.0 5.0 2.0 2.0 4.0 4.0 2.0 2.0 4.0 2.5 1.0 1.0 2.0 4.0 2.0 2.0 2.5 4.0 4.0 2.0 1.5 5.0 5.0 2.0 2.5 0 / -6.0 0 / -3.0 0 / -3.0 0 / -4.0 6.0 2.0 2.0 4.0 5.0 2.0 2.0 4.0 3.0 1.0 1.0 2.0 5.0 2.0 2.0 2.5 4.0 4.0 2.0 1.5 5.0 5.0 2.0 2.5 0 / -7.0 0 / -4.0 0 / -4.0 0 / -4.0 7.0 4.0 4.0 4.0 5.0 4.0 4.0 4.0 3.5 2.0 2.0 2.0 5.0 3.0 3.0 4.0 4.0 4.0 2.0 1.5 5.0 5.0 2.0 4.0 0 / -8.0 0 / -4.0 0 / -4.0 0 / -5.0 8.0 4.0 4.0 5.0 6.0 4.0 4.0 5.0 4.0 2.0 2.0 2.5 6.0 3.0 3.0 5.0 5.0 5.0 2.5 2.5 6.0 5.0 2.5 5.0
P4 Sd max HG Plane running of the face side with respect to the bore UP face runout P2 P4 Sia max HG Plane running of the face side with respect to the raceway, UP in the assembled bearing axial runout P2 BS single bearing Deviation of a single inner ring from nominal dimension width tolerance BS paired bearing Deviation of a single inner ring from nominal dimension width tolerance P4 HG UP P2 P4 HG UP P2
P4 HG Identical with BS of the inner ring of the same bearing UP P2 P4 HG Identical with BS of the inner ring of the same bearing UP P2 P4 HG UP P2 2.5 2.0 2.0 1.5 2.5 2.0 2.0 1.5 2.5 2.0 2,0 1.5 3.0 2.0 2.0 1.5 4.0 2.0 2.0 1.5 5.0 - - 2.5 5.0 2.5
68
2.5 2.5
69
www.gmn.de
Optimization of the t
at high speeds With increasing speeds (from about n dm = 1.5 106 mm/min) progressively rising centrifugal force can cause widening of the inner ring and lead to the following functional impairments. Inner ring slippage on the shaft and contact surfaces Fretting corrosion Vibrations A tighter t is recommended to prevent the inner ring from lifting off.
Bore code
Bore diameter
d [mm]
1.5 1 1 2 2 2 3 4 4 5 6 7 8 8 9 10 10 11 12 12 13 14 15 15 17
1.75 1 2 2 3 3 4 5 6 7 8 9 10 11 13 13 14 15 16 17 18 19 20 21 23
2.0 2 2 3 4 4 5 7 8 9 11 12 13 15 16 17 18 19 21 22 23 25 26 27 30
2.25 2 3 4 5 5 7 8 10 12 13 15 17 19 21 21 23 25 26 28 30 31 33 34 38
2.5 3 4 5 6 6 9 10 12 15 17 19 21 23 26 26 29 30 33 34 37 39 41 42 47
00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 24
t1 A Ra d Ra t3 AB Ra t2 AB Ra d B
Valid for solid shaft For hollow shaft (50 %): Correction factor = 0.8
Ra Ra t2 AB
Ra Ra
Correction factors for interference of bearing types and bearing series D SM 60.. SM 619.. KH 60.. KH 619.. 1 1.10 1.05 1.15
71
www.gmn.de
Bearing lubrication
Lubricant selection
In order to fully exploit the performance capacity of GMN high precision bearings in machine operation, it is especially important to consider suitable bearing lubrication. Maximum speeds as well as maximum service life are based on the formation of a friction-reducing lubricant lm between rolling and sliding bearing parts. Other objectives of lubrication are: Attenuation of structure noise and vibrations Thermal dissipation Sealing effect Corrosion protection The increasing speed viability of modern high-speed lubricants permits greater utilization of the user-friendly, economic advantages of grease lubrication. Operational requirements which exceed the performance capability of grease lubricants can be handled by oil-lubricated bearings to obtain maximum service life at the highest speed and temperature ranges. Criteria for lubrication type selection Lubricant Speed suitability up to about n dm [106 mm/min] Service life Design/system costs Operating costs Heat dissipation Running in procedure Pollution +++++: very good +: poor Grease +++ 2.0 +++ +++++ +++++ ++ ++ +++++ Oil +++++ 34 +++++ + + ++++ ++++ +
Grease lubrication
Speed suitability of greases
Selection of a suitable grease for high precision bearings is essentially based on the bearing's maximum operating speed. The reference speed factor, n dm, accommodates the operational speed of the bearing and indicates the maximum speed capacity of the lubricant sought. Accommodation of the speed factor when selecting a lubricant precludes degradation of bearing performance due to decient lubrication. A speed-induced break-down of the lubrication lm can lead to mixed friction, heating, and increased wear on the bearing. Reference speed factor: n dm n dm bearing = n (D + d)/2 [mm/min] n: Bearing operating speed [1/min] d: Bearing bore diameter [mm] D: Bearing outer diameter [mm] Numerous lubricant manufacturers offer a comprehensive range of greases developed for use with high speed or heavily loaded ball bearings. Particular characteristics, such as protection against wear, low noise level and temperature resistance, are specically emphasized during production by an application-oriented combination or processing of the base oil, thickener and additives.
LUBCON synth. TURMOGREASE Lithium hydrocarbon + Li 802 EP mineral oil 0.87 0 2 82 12.5 -35 to +140 1000000 Resistant to corrosion and aging; compatible with non-ferrous metals; good pressure absorption; good long-term stability; low noise
0.94
II
2/3
25
-40 to +120
2200000
LUBCON Special Ester + TURMOGREASE Lithium synth. 0.94 II 2 18 4.5 -70 to +120 Highspeed L 182 hydrocarbon
2500000
Polyurea
Ester
1.0
III
70
10.7
-40 to +180
1300000
High temperatures; good protection against corrosion and aging; compatible with elastomers such as FKM/Viton
0.94
II
25
-50 to +140
1000000
Suitable for low temperatures; low noise; low frictional moment; standard grease in shielded deep groove ball bearings Very good wear protection; very low frictional moment; especially suitable for hybrid bearings with ceramic balls; good corrosion protection; good resistance to water and media; resistant to aging and oxidation
0.94
II
23
4.7
-50 to +120
1300000
72
www.gmn.de
Grease re-lubrication
Position of lubricant supply holes
O arrangement 2 B -0.5 B+B0 +0.25 - 0.5 B-B0+0.25 - 0.5
offset by 90
Oil lubrication
Oil lubrication systems
Tandem arrangement 2 B -0.5 B+B0+0.25 - 0.5 B0 0.25
offset by 90
Compared to grease-lubricated bearings, the application of lubricating oils enables long-term reliable operation at maximum speeds. Different methods are available for the supply of oil to high speed bearings: Oil air lubrication (minimum quantity lubrication) Oil injection lubrication Oil fog lubrication
4 B1
4 B1
6000 8 8 9 10 12 12 13 14 15 16 16 18 18 18 20 6001 6002 6003 6004 6005 6006 6007 6008 6009 6010 6011 6012 6013 6014
KHAG
B 0
[mm] 5.5 5.5 6.1 6.6 8.1 8.1 8.6 9.2 9.7 10.2 10.3 11.5 11.5 11.5 12.7
B1
1.5 1.5 1.5 1.5 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0
61904 61905 61906 61907 61908 61909 61910 61911 61912 61913 61914 9 9 9 10 12 12 12 13 13 13 16
KHAG
B 0
[mm] 6.2 6.2 6.2 6.7 8.1 8.1 8.1 8.7 8.7 8.7 10.3
B1
1.5 1.5 1.5 1.5 2.0 2.0 2.0 2.0 2.0 2.0 2.0
6000 6001 6002 6003 6004 6005 6006 6007 6008 6009 6010 6011 6012 6013 6014 6015 6016 6017 6018 6019 6020 6021 6022 6024 8 8 9 10 12 12 13 14 15 16 16 18 18 18 20 20 22 22 24 24 24 26 28 28
S/SMAG
B 0
[mm] 5.9 5.9 6.4 6.9 8.0 8.0 8.7 9.2 9.8 10.3 10.4 11.4 11.5 11.5 12.8 12.6 13.7 13.7 14.9 14.9 14.9 16.0 17.1 17.1
B1
1.5 1.5 1.5 1.5 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0
61904 61905 61906 61907 61908 61909 61910 61911 61912 61913 61914 61915 61916 61917 61918 61919 61920 61921 61922 61924 9 9 9 10 12 12 12 13 13 13 16 16 16 18 18 18 20 20 20 22
SAG
B 0
[mm] 6.2 6.2 6.2 6.8 8.1 8.2 8.2 8.8 8.8 8.8 10.4 10.3 10.5 11.5 11.5 11.5 12.7 12.7 12.7 13.8
B1
1.5 1.5 1.5 1.5 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 Oil pump Oil dosing element
Mixing chamber
Specic, volume-regulated lubricant supply Low oil consumption Low oil fog formation Very good lubricating effect Environmentally friendly and highly economical Oil cooling and oil ltering not required (in comparison to oil injection lubrication)
B= bearing width (single bearing) B0= Axial distance to shielded side B1 = Bore diameter Other types/sizes on request.
74
75
www.gmn.de
Oil lubrication
Oil supply
Conventional bearing lubrication systems have oil injection nozzles in an intermediate sleeve or in a spacer between 2 bearings. Length and bore diameter of the oil nozzle: Sufcient lubricant supply is assured with a ratio of nozzle length/ nozzle bore diameter of more than 3 and less than 5 (pressure of oil air current greater than opposing pressure generated by bearing turbulences). Oil for high precision spindles: Hydraulic oil with kinematic viscosity VG 32 or VG 46 mm2/s Oil ltering: Purity class 13/10 per ISO 4406:99 (particle size < 5 m) Oil volume per lubrication pulse: 30 up to 35 mm3 per connection for 1 or 2 bearings Cycle time: VG32: 2 to 4 min., VG46: 410 min. (independent of dbearing) A nozzle position aligned parallel to the spindle axis is sufcient for applications in high speed ranges. A nozzle position aligned at an angle increases bearing speed suitability (more accurate lubricant supply in the rolling area). Number of nozzles: 1 per bearing Nozzle diameter: 1.2 mm (dbearing < 50 mm) .. 1.6 mm (dbearing > 70 mm) Nozzle position: Between cage and inner ring rim (technical data tables, TA cage) Oil supply, oil drain: Transparent hose, di = 4 mm Air pressure upstream of spindle: 0,6 to 1 bar Air volume: 3 to 4 m3/h (50 to 65 L/min)
Oil nozzle Oil nozzle
Comparison: oil air lubrication / direct oil air lubrication Oil air lubrication through spacer
Outer spacer
spacer
Inner spacer
Reduced consumption of compressed air and oil (better dosage of lubricant volume) Separate lubricant volume regulation per single bearing Specic lubricant supply to roller contact points Less sensitive to axial air current (in comparison to conventional oil air lubrication) GMN offers special designs for direct oil lubrication which provide versatile and effective solutions with respect to oil supply and effective sealing. Oil supply through outer ring, open side Oil supply through outer ring, shielded side O-rings in outer ring (sealing) Broadened groove for expanded oil supply potential, tolerance compensation
Air quality: Meets ISO 8573: particle size < 5 m, particle concentration < 5 mg/m3, dew point < 3C, oil concentration < 1 mg/m3 Start-up: Spindle start-up only after oil supply is secured
76
77
www.gmn.de
Oil lubrication
Lubricant supply through the outer ring Oil supply/ sealing
Oil supply via open side No overrun of oil supply at high axial loads Oil supply via closed side Oil supply directly on rolling contact Maximum speed suitability
Lubricating oils
Mineral lubricating oils achieve adequate bearing lubrication for the lubrication of machine tool spindles. Frequently used lubricating oils Kinematic temperature Operating Flashpoint viscosity range [C] Remarks / Application Oil type Pour point [C] [mm2/s] [C] 40C 100C Mineral Mineral Synthesis Silicone -33 -25 -60 -65 -68 + 120 +226 +220 +280 +220 32.0 46.0 12.2 60 14.3 5.4 6.7 3.2 20 3.7 -25 to +80 -15 to +110 -35 to +130 -55 to +200 -50 to +120
Good wear protection; good corrosion and aging resistance Good wear protection; good corrosion and aging resistance Low evaporation, particularly at low temperatures, resistant to oxidation and corrosion / gyro bearings High and low temperature oil / aerospace and aviation industries, ne mechanics Good corrosion and aging resistance, low evaporation / aircraft and instrument bearings
Special designs A, AB
Seal in the housing Maximum bearing stability
Special designs L, LB
Seal in bearing outer ring No housing adaptation required
Ester
Special designs R, RB
without seal low capital expenditure Advantageous for axial xation on outer ring and narrow housing ts Wide lubrication groove
Detailed information on bearings with lubricant supply through the outer ring: www.gmn.de
78
79
www.gmn.de
Speed limits
GMN develops ball bearings for highest speed and maximum load to optimize the efciency and service life of machines. A bearing's speed limit is a decisive quantity. As speed increases, the running friction and thus bearing temperature rises progressively in the area of contact surfaces between balls and rings. The friction generated in the bearing is decisively inuenced by: Speed Bearing load Lubricant viscosity Lubricant quantity The speed values provided in the bearing tables are nominal speed limits for a spring-preloaded bearing under normal operating conditions. Good heat dissipation Low external load Rotating inner ring Oil air lubrication or oil fog lubrication Good shape and positioning accuracy of associated parts Good alignment of associated parts Good balancing of rotating parts Use of suitable oil or grease Cleanliness in assembly and operation 0.75 1.0 F 1.0 Bearing preload L M S If operating conditions deviate from the conditions stated then correction factors must be taken into account. (Correction factors and speed values are only guidelines) GMN stands ready to answer questions about your special application on the basis of its broad experience.
Speed limits: GMN spindle bearings Permissible speed = speed value n fn1 fn2 fn3 fn4 Correction factors fn1: lubrication Grease lubrication (observe n dm grease factor) Oil air or oil fog lubrication fn2: bearing arrangement/ pairing Single bearing with spring preload Rigid preload fn3: kinematics Rotating inner ring Rotating outer ring fn4: ball material Steel Ceramic (Si3N4) 80 1.0 0.6 1.0 1.25 0.8 0.75 0.7 0.6 0.65 0.7 0.6 0.6 0.5 0.5 0.5 0.4 0.4 0.3 0.3
Speed limits: GMN deep groove ball bearings Permissible speed = speed value n fn1 fn2 fn3 fn4 fn5 Correction factors Korrekturfaktoren fn1: lubrication fn2: cage fn3: kinematics fn4: bearing arrangement/pairing fn5: ball material grease lubrication (observe the grease's n dm factor) Oil air lubrication J T9H TBH TA TB MA (n dm < 625 000 mm/min) (n dm < 1 400 000 mm/min) (n dm < 1 000 000 mm/min) (n dm < 1 600 000 mm/min) (n dm < 1 400 000 mm/min) (n dm < 1 350 000 mm/min) 1 1.25 1 1.6 1.2 1.8 1.6 1.5 1.0 0.6 1.0 0.8 1.0 1.25
rotating inner ring rotating outer ring single bearing with spring preload Pairs per DF, DB, DT, DUA, DUO, DUV steel ceramic (Si3N4)
81
www.gmn.de
Storage
Appropriate storage of GMN products assures their bearing-specic performance features until installation. Store bearings in their original packaging Protect them from dust and moisture Protect them from temperature and moisture uctuations Shelf-life of preserved, grease-lubricated ball bearings: Max. 2 years (in proper storage)
Installation preparation
Careful preparation of the installation environment and relevant components assure unrestricted utilization of GMN ball bearing performance characteristics. Preparation of the installation environment Keep the installation environment clean and free of dust and compressed air Have necessary measuring and assembly tools at hand Allow all parts to adapt to the prevailing temperature Clean associated components Check condition and dimensions of associated components Preparing components Unpack ball bearings just before installation Do not rinse out ball bearings. Most greases and lubricating oils are entirely compatible with the bearing's preservative oil. Preparation for grease lubrication: Have the necessary type and quantity (precision scales) of grease at hand Spread grease on both sides of the balls / raceways with a dosing syringe.
Notices about grease distribution run Avoid external loads Accelerate to a fraction of nominal speed in about 20 seconds Take into account the type of grease (viscosity) and quantity Monitor the development of temperature and noise (at more than 60C housing temperature or extreme noise: stop grease distribution run and resume after a rest period) Smooth running and steady temperature levels conrm a successfully completed grease distribution run Machine run intervals for grease distribution run
Phase 1
Brief intervals of reduced speed 1. Distribution intervals at 0.33 nmax Distribution 1 min Standstill 2 min Distribution 1 min Standstill 2 min Distribution 1 min Standstill 2 min Distribution 1 min Standstill 2 min
2. Distribution intervals at 0.66 nmax 1 min 2 min 1 min 2 min 1 min 2 min 1 min 2 min
Bearing installation
Match the dimensions of the bearings and associated components to one another (ts) Push or pull ball bearings in the axial direction precisely (do not cant) Do not transmit installation force through the balls When press tting, warm the inner ring (maximum 100C). (note: axial shrinkage due to cooling) Detailed installation information: www.gmn.de
3. Distribution intervals at 1.0 nmax 1 min 2 min 1 min 2 min 1 min 2 min 1 min 2 min
Phase 2
Long intervals at maximum speed Distribution intervals at nmax Distribution 30 min Standstill 5 min Distribution 30 min
82
83
www.gmn.de
* Clamping force values and tightening torques are guidelines based on experience and may deviate according to application.
84
85
www.gmn.de
Bearing calculation
The service life calculation assesses a bearing solution with consideration for bearing material fatigue under dened operating conditions. Calculation methods per DIN ISO 76 (static load rating) and DIN ISO 281 (dynamic load rating and service life) GLOBUS bearing calculation program from GMN GMN offers an option for performing these calculations by running the GLOBUS ball bearing calculation program on a computer; this permits selection of various service life solution options from the comprehensive product line.
6. X and Y factors
e Single bearing Tandem arrangement X Fa / Fr e Y X Fa / Fr > e Fa / Fr e Bearing pair in X or O arrangement Y X Fa / Fr > e
0.38 0.40 0.43 0.46 0.47 1 0 0,44 0.50 0.55 0.56 0.56 0.57 0.68 1 1 0 0 0.43 0.41
1.47 1.40 1.30 1.23 1.19 1 1.12 1.02 1.00 1.00 1.00 0.87 1 1
1.65 1.57 1.46 1.38 1.34 0.72 1.26 1.14 1.12 1.12 1.09 0.92 0.7 0.67
2.39 2.28 2.11 2.00 1.93 1.82 1.66 1.63 1.63 1.63 1.41
Contact angle 20 Contact angle 25 Radial clearance CN (p. 49) Deep groove ball bearings
0.014 0.028 0.056 0.085 0.110 0.170 0.280 0.420 0.560
0.23 0.26 0.30 0.34 0.36 1 0 0,56 0.40 0.45 0.50 0.52 0.29 0.32 0.36 0.38 0.40 1 0 0,46 0.44 0.49 0.54 0.54
2.30 1.99 1.71 1.55 1.45 1 1.31 1.15 1.04 1.00 1.88 1.71 1.52 1.41 1.34 1 1.23 1.10 1.01 1.00
2.78 2.40 2.07 1.87 1.75 0.78 1.58 1.39 1.26 1.21 2.18 1.98 1.76 1.63 1.55 0.75 1.42 1.27 1.17 1.16
3.74 3.23 2.78 2.52 2.36 2.13 1.87 1.69 1.63 3.06 2.78 2.47 2.29 2.18 2.00 1.79 1.64 1.63
4. Axial loading Fa
Fa = Ka [N] (if Ka > 3 FV) Fa = FV + 0.67 Ka [N] (if Ka 3 FV) Ka: External axial force [N] FV: Preload [N]
n : Speed [1/min] C : Dynamic load rating [N] 3. P : Equivalent bearing load [N] 5. 86
( ) [h]
3
C0 : static load rating [N] e : Loading ratio: radial/axial load For Tandem arrangement: i = 1; C0 and Fa : Use single bearing values
87
www.gmn.de
Bearing calculation
7. Life adjustment factor aISO
eC Cu aISO = ,k P eC : Contamination factor 7.2. C0 Cu = 22 for bearings with dm 100 mm
7.1 Viscosity ratio k v k = v1 v : Operating viscosity 7.1.1 v1 : Reference viscosity 7.1.2 (good lubrication: k = 2.5 to 4.0)
For k < 0.1, an extended service life calculation is not possible
7.2
C0 100 Cu = 22 dm
( )
0,5
Cu : Fatigue limit load P : Equivalent bearing load 5 Life adjustment factor aISO
50
100
100
High cleanliness
k= 4 2
) (
50
Tb : Operating temperature = 0.6 130 [C] v40 : Lubricant operating viscosity at 40C v100 : Lubricant operating viscosity at 100C
0.4 (For grease lubrication: v = viscosity of the base oil) Operating viscosity v [cSt] or [mm2/s] at 40C at 100C 25 25 46
2
Speed [1/min]
500 1.0 00 1.50 2,0 0 00 3,0 00 0
200
Very ne ltering of the oil supply; typical conditions for a shielded bearing with lifetime grease lubrication
0.8 to 0.6
0.9 to 0.8
Normal cleanliness
20
Oil ltered through a ne lter; typical conditions for a shielded bearing with lifetime grease lubrication
0.6 to 0.5
0.8 to 0.6
20
Slight contamination
Slight contamination in the lubricant
10
Lubricant (Examples) Klueber Isoex GLY 32 0.3 Lubcon Turmogrease Highspeed L252 Mineral oil Operating viscosity [mm /s]
5 6 6.8 10
20,
5,0 0 10,0 00 0 00
Moderate contamination
0.5 to 0.3
0.6 to 0.4
2 0.2 1
100 5 50 3
50, 100 ,00 0 00 0
Typical conditions for bearings without an installed seal; rough ltration; wear particles and foreign particles from the environment
0.3 to 0.1
0.4 to 0.2
Severe contamination
Bearing environment heavily polluted and bearing arrangement not adequately sealed 50 100 200 Pitch circle diameter: dm [mm]
0.1 to 0
0.1 to 0
0.5
0.15 10
10
D+d dm = 2
20
0.2
5 0.1
0.1
0.005 0.01
0.02
0.05
0.1
0.2
0.5
Cu eC P
88
89
www.gmn.de
100,000 50,000 20,000 30,000 10,000 5,000 3,000 2,000 1,000 500 300 200 20
Ceramic
Steel
30
50
70
100
Operating conditions* for lubrication interval reference points tf Standard greases on the basis of lithium saponication Operating temperature up to 70C Bearing load (P/C < 0.1) Favorable ambient conditions with respect to ... ... dust ... humidity ... air currents through the bearing *(according to GfT Worksheet 3, "Roller Bearing Lubrication", Sept. 2006) Higher operating temperatures cause a reduction of the lubricating interval. (Beyond an operating temperature of 70C, a further heatup of 15 Kelvin will lead to a lubricating interval which is only half the initial period.) Higher bearing loads (P/C > 0.1), jerky loads and vibrations require appropriate corrections to lubricating interval reference values tf. If exceptional load conditions prevail, GMN will provide consultation about special greases optimized for the specic requirements.
kf = 0.75 for spindle bearings with contact angle 15 kf = 0.90 for spindle bearings with contact angle 25 kf = 0.9 1.1 for deep groove ball bearings
The inuences of bearing type, contact angle and bearing arrangement on bearing stability are incorporated by way of the radial/axial factors. Single bearing Tandem arrangement
Radial/axial factor Spindle bearing =15 Spindle bearing =25 Deep groove ball bearing
90
www.gmn.de
Bearing frequencies
Structure-borne noise
The design and geometry of the individual components, as well as the design of the entire bearing, determine bearing frequencies. The characteristic structure-borne noise level of a ball bearing is composed of the sum of all bearing frequencies. Structure-borne noise relevant factors: Form accuracy and surface grade of raceways and balls Cage version Cleanliness and type of lubrication On the basis of structure-borne noise tests, bearing vibrations can be determined and conclusions drawn about the surface condition (waviness) of bearing rings and balls. Low noise levels are the result of smooth running and low friction which indicate high performance and long service life of the bearing. Calculation of bearing-specic frequencies Ball passing frequency fAR on outer ring: Z DW fAR = fi 1 cos 0 [1/sec] 2 dm
Micrometer
2,0 1,5 1,0
Service
GMN bearing analysis
More than 50 % of all bearing damage results from inadequate lubrication, more than 40 % is caused by faulty design, installation defects and contamination. Less than 1 % of all bearings fail due to material or manufacturer defects. Bearing analyses performed by GMN permit conclusions to be drawn about the causes of impairment and provide solutions which enable reliable operation of the bearing application. Assessment of cause(s) of bearing damage or inadequate processing results Consultation about cause elimination Prevention of same or similar damage Optimization of the bearing with respect to machine duty cycle, processing accuracy and performance Use of analysis results for product improvements GMN offers comprehensive investigative methods for bearing analysis. Noise test
fi=Shaft frequency [1/s] DW=Ball diameter [mm] dm=Pitch circle diameter [mm] Z=Number of balls 0=Contact angle
Consultation
On the basis of long experience in the practical application of machine components, GMN provides comprehensive consultation and services in the eld of high precision ball bearings that support 0 machine systems. Bearing selection, bearing calculation, service life calculation Characteristic values, bearing frequencies, installation dimensions Tribology, lubrication, lubricant selection, grease consumption life calculation Recoding of competitive products Optimizations for special applications Special solutions Damage analysis
0,5 0,0 -0,5 -1,0 -1,5 -2,0 51,9 52,0 52,1 52,2 52,3 52,4 52,5 52,6 52,7 52,8 52,9 53,0 53,1 53,2 53,3 53,4 53,5 53,6 53,7 53,8
Millimeter
( (
) )
Ball passing frequency fiR on inner ring: Z DW f IR = fi 1 + cos 0 [1/sec] 2 dm Ball circulation frequency fW : fi dm DW f W = cos2 0 [1/sec] 2 DW dm
Training courses
GMN provides qualied training courses in theory and practice for high precision ball bearings and their applications, both at customer locations and also at our premises. Subjects and contents of training courses are focused on the individual customer requirements. Essentials: products, designs, materials, accuracies and tolerances Engineering: nomenclature, bearing selection, bearing arrangements, preload, matching, lubrication, calculation Installation: workplace layout, tools, control measurements lubrication, installation, grease distribution run Bearing analysis: reasons for bearing investigations, methodology, investigation options at GMN
Metrological investigation (bearing and component measurements) Microscopic investigation (including REM) Lubricant analysis Calculation review (e.g. check of preload) Weak-point analysis In order to achieve specic and meaningful results in bearing analysis, the following approach should be pursued: Remove the bearing immediately after the damage event or operating abnormality Mark the installation position (xed/oating bearing, load direction, drawing/sketch) Return the bearing uncleaned with all parts Inform us about the application, operating conditions, load, speed and time installed
92
93
www.gmn.de
Special applications
GMN develops special bearings and complete solutions that set the technical benchmark for numerous application proles: Touchdown bearings Vacuum technology / turbo molecular pumps Medical technology / X-ray Bearing systems Instrument and navigation technology Machine tool applications A global GMN service network offers competent customer consultation and customer-oriented solutions. Vacuum technology / turbo molecular pumps High speeds Optimized lubrication Long service life Low noise level Cleanliness Materials suitable for vacuum Medical technology / X-ray Dry lubrication Temperature insensitive up to 550C Ultra-high vacuum (10-7 to 10-9 mbar) No particles or contamination Low operating noise High surface pressure Bearing systems Production and engineering from a single source Low vibration operation Optimal adaptation to connection points High running accuracy Touchdown bearings Full complement bearings Economic 3-bearing systems for limited installation space Robust 4-bearing systems High acceleration to nal speed High number of touchdowns and "touch-and-goes"
Instrument and navigation technology Maximum running accuracy Ready-to-install preloaded bearing systems Low frictional moments Associated components of utmost precision Matched bearings with lifetime lubrication Machine tool applications Special series optimized for specic requirements High speeds Special materials Lifetime lubrication Optimized design (radial clearance, matching, special lubrication) 94 95
www.gmn.de
Index
Associated component tolerances Ball bearing tolerances Bearing analysis Bearing arrangements Bearing comparisons GMN series Competition Bearing data Spindle ball bearings Deep groove ball bearings Bearing designation Deep groove ball bearings Spindle ball bearings Bearing frequencies Bearing lubrication Bearing sets Bearing selection Bearing storage Boundary dimensions Clamping force Clearance Deep groove ball bearings Consultation Contact angle 7071 6869 93 6465 59 44 2243 5255 20 50 92 7279 65 5759 82 9 85 49 93 67 Deep groove ball bearing cages J T9H TBH TA ; TB Deep groove ball bearing series 60../62.. Z/2Z X-2Z Direct lubrication Grease Oil Direct oil lubrication Direct oil lubrication bearing versions +A +AB +L +LB Fits Fixed bearings Floating bearing Grease distribution run Grease ll quantities Grease lubrication Grease re-lubrication Greased bearings 48 Hybrid ball bearings Installation Internet, downloads 7, 46 Lift-off force Matching accuracy Materials Spindle ball bearings Deep groove ball bearings Model series Nut tightening torque Oil lubrication Precision nuts Preload Spring Rigid Processing tolerances Quality management Rigidity 1213, 47 82 98 60, 63 67 1013 4748 9 8485 1617, 7579 84 61 6263 71 98 60 Sealed bearings Service life calculation Service Service life: grease Shape and position tolerances Special applications Spacers Speeds Spindle ball bearings Deep groove ball bearings Speed limits Speed correction factors Spindle ball bearings Deep groove ball bearings Spindle ball bearing series S SM KH BHT BNT Spindle ball bearing cages TA TXM Static load capacity Tightening torque Training courses 7, 15, 46 8690 93 90 71 9495 66 2243 5255
80 81 67, 1419
1011
91 85 93
96
97
www.gmn.de
Internet At our Internet site www.gmn.de we provide comprehensive product information that can be downloaded. GMN GMN Paul Mller Industrie GmbH & Co. KG manufactures high precision ball bearings, machine spindles, freewheel clutches and seals for a broad spectrum of applications at its Nuremburg, Germany plant. On the basis of long experience in the development and production of machine components, GMN has specialized in the manufacture of high quality products in the eld of high precision ball bearings and, beyond a comprehensive standard product line, also offers customer-oriented special solutions. A global GMN service network offers competent customer consultation and individualized solutions. GMN Quality management tested and certied. GMN guarantees utmost quality for its products and services that is based on long-term reliability. Highly modern development and production methods ensure products that always represent state-of-the-art technology. All GMN corporate divisions are structured for transparency and clear organizational workows to ensure customer-oriented services and economic security. All GMN corporate divisions are certied to DIN ISO 9001:2008 .
GMN High precision ball bearings Spindle technology Freewheel clutches Non-contact seals
GMN safeguarding the future. For GMN, progress means the best possible customer support combined with performance-oriented optimization of its technical products. This claim is realized at GMN under especially strict observance of national and international environmental standards with regard to efcient, responsible utilization of ecological resources.
This catalog is current to the time of printing. No liability is accepted for technical revisions, inadvertent mistakes and printing errors.
98