Professional Documents
Culture Documents
: Date:
Specifier's comments: This anchor design calculation is subject to the comments and approval of the strucutral engineer of the project.
1 Input data
Anchor type and diameter: Effective embedment depth: Material: Evaluation Service Report: Issued I Valid: Proof: Stand-off installation: Anchor plate: Profile: Base material: Installation: Reinforcement: HIT-RE 500 + HIT-V (5.8) M16 hef,opti = 192 mm (hef,limit = 314 mm) 5.8 ETA 04/0027 6/26/2013 | 5/16/2018 design method ETAG BOND (EOTA TR 029) eb = 0 mm (no stand-off); t = 16 mm lx x ly x t = 270 mm x 250 mm x 16 mm; (Recommended plate thickness: not calculated) no profile uncracked concrete, C20/25, fcc = 25.00 N/mm2; h = 350 mm, Temp. short/long: 40/24 C hammer drilled hole, installation condition: dry no reinforcement or reinforcement spacing >= 150 mm (any ) or >= 100 mm ( <= 10 mm) no longitudinal edge reinforcement Geometry [mm] & Loading [kN, kNm]
Input data and results must be checked for agreement with the existing conditions and for plausibility! PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.com.ph Company: Specifier: Address: Phone I Fax: E-Mail: Page: Project: Sub-Project I Pos. No.: Date:
Tension
3.2 Combined pullout-concrete cone failure Ap,N [mm2] 400117 yc 1.000 ec1,N [mm] 0 N0 Rk,p [kN] 144.765
2 A0 p,N [mm ] 204800 2 tRk,ucr [N/mm ] 15.00 2 tRk,ucr,25 [N/mm ] 15.00
scr,Np [mm] 453 yg,Np 1.000 yec2,Np 1.000 NRd,p [kN] 134.679
0
ccr,Np [mm] 226 yg,Np 1.000 ys,Np 1.000 NSd [kN] 110.000
cmin [mm]
yre,Np 1.000
3.3 Concrete Breakout Strength Ac,N [mm2] 571536 ec1,N [mm] 0 N0 Rk,c [kN] 134.352 3.4 Splitting failure Ac,N [mm2] 471145 ec1,N [mm] 0 N0 Rk,c [kN] 134.352
2 A0 c,N [mm ] 256441 2 A0 c,N [mm ] 331776
scr,N [mm] 576 yec2,N 1.000 NSd [kN] 110.000 ys,N 1.000 yre,N 1.000 k1 10.100
Input data and results must be checked for agreement with the existing conditions and for plausibility! PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.com.ph Company: Specifier: Address: Phone I Fax: E-Mail: Page: Project: Sub-Project I Pos. No.: Date:
Comments: Tension displacements are valid with half of the required installation torque moment for uncracked concrete! Shear displacements are valid without friction between the concrete and the anchor plate! The gap due to the drilled hole and clearance hole tolerances are not included in this calculation! The acceptable anchor displacements depend on the fastened construction and must be defined by the designer!
6 Warnings
To avoid failure of the anchor plate the required thickness can be calculated in PROFIS Anchor. Load re-distributions on the anchors due to elastic deformations of the anchor plate are not considered. The anchor plate is assumed to be sufficiently stiff, in order not to be deformed when subjected to the loading! Checking the transfer of loads into the base material is required in accordance with EOTA TR 029, Section 7! The design is only valid if the clearance hole in the fixture is not larger than the value given in Table 4.1 of EOTA TR029! For larger diameters of the clearance hole see Chapter 1.1. of EOTA TR029! The accessory list in this report is for the information of the user only. In any case, the instructions for use provided with the product have to be followed to ensure a proper installation. Characteristic bond resistances depend on short- and long-term temperatures. Please contact Hilti to check feasibility of HIT-V rod supply. Edge reinforcement is not required to avoid splitting failure
Input data and results must be checked for agreement with the existing conditions and for plausibility! PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.com.ph Company: Specifier: Address: Phone I Fax: E-Mail: Page: Project: Sub-Project I Pos. No.: Date:
7 Installation data
Anchor plate, steel: Anchor type and diameter: HIT-RE 500 + HIT-V (5.8), M16 Profile: no profile; 0 x 0 x 0 mm Installation torque: 0.080 kNm Hole diameter in the fixture: df = 18 mm Hole diameter in the base material: 18 mm Plate thickness (input): 16 mm Hole depth in the base material: 192 mm Recommended plate thickness: not calculated Minimum thickness of the base material: 228 mm Cleaning: Manual cleaning of the drilled hole according to instructions for use is required.
7.1 Required accessories Drilling Suitable Rotary Hammer Properly sized drill bit Cleaning Manual blow-out pump Proper diameter wire brush y Setting Dispenser including cassette and mixer Torque wrench
135
135
35 180 125
2 35
45
180
45
Coordinates Anchor [mm] Anchor 1 2 3 4 x -90 90 -90 90 y -90 -90 90 90 c-x c+x c-y c+y -
Input data and results must be checked for agreement with the existing conditions and for plausibility! PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
125
www.hilti.com.ph Company: Specifier: Address: Phone I Fax: E-Mail: Page: Project: Sub-Project I Pos. No.: Date:
Input data and results must be checked for agreement with the existing conditions and for plausibility! PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan