Professional Documents
Culture Documents
COPPER TAPE CONDUCTOR - for earthing and air termination Size: 25 mm x 3 mm Code: C-150 40 mm x 3 mm Code: C-151 50 mm x 3 mm Code: C-152 25 x 3: As required 40 x 3 +/- 70 m & 50 x 3: +/- 50 m HC annealed copper
Coil: Material:
TAPE GUIDE - supports ridge and down conductors Fits copper sizes: 25 mm x 3 mm 40 mm x 3 mm 50 mm x 3 mm Material: Brass Code: P-232 Code: P-233 Code: P-234
TAPE CLAMP - SQUARE - clamping of copper tape Fits copper sizes: 25 mm x 3 mm 50 mm x 3 mm Material: Brass Code: P-238 Code: P-235
TEST CLAMP FLAT : FLAT - test joint for easy disconnect point Fits copper sizes: 25 mm x 3 mm 50 mm x 3 mm Material: Brass Code: P-236 Code: P-237
COPPER SOLID CONDUCTOR - for earthing Size: Coil: Material: 10 mm dia. approx 70 m HC annealed copper Code: C-190
COPPER STRANDED CONDUCTOR - for earthing - bare BCEW Size: 16 mm 25 mm 35 mm 50 mm Code: C-BCEW16 Code: C-BCEW25 Code: C-BCEW35 Code: C-BCEW50
Material:
70 mm 95 mm HC copper
INSULATED COPPER STRANDED CONDUCTOR (for earthing) Green/Yellow Size: 35 mm 50 mm 70 mm 95 mm HC copper Code: C-GP35GY Code: C-GP50GY Code: C-GP70GY Code: C-GP95GY
Material:
Fits M16 & 5/8 UNC for 70mm2 conductor. Brass Q-100
Fits M16 & 5/8" UNC for 120mm2 conductor. Brass Q-103
EARTH CLAMP
Manufactured from brass and suitable for connecting cable or flat tape to M16 mm earth rod or rebar. Different combinations of joint are achieved by assembling the plates in different configurations on the U-bolt. See insert pictures below. Light Duty: Conductor 25-70mm2 Heavy Duty: Conductor 25-95mm2 Tape up to 25x3mm Tape up to 30x3mm M8 U-Bolt Y10 to Y25 Rebar M10 U-Bolt Y25 to Y32 Rebar Code: Q-101 Code: Q-102
On THREADED earth rod with coupler. M16 High tensile steel. Q-120
Used: Size:
For driving of earth rods, easy to use. Complete with driving sleeves. Drives rod flush with ground. M16 and 5/8UNC & 16mm and 5/8
Material: Code:
DENSO PASTE and DENSO TAPE An easy to use 'paste' to eliminate moisture ingress. Paste Size: 500g Bucket. Code: Q-180 Tape Size: 50mm x 10m Roll Code: Q-190
EARTH BRAID - for earth bonding of metal gates, doors, fences etc. Available in Red or Tinned copper. Material: HC copper Length: L mm 100, 150, 200, 250 & 300
EARTH RESISTANCE TESTER The Earth Resistivity measurement is useful for soil surveys to establish the optimum ear The K4106 is a 2/3/4-wire digital Earth resistance/Earth Resistivity Tester equipped with measure earth resistances and calculate earth resistivity's (), using the "Wenner" 4 pole Code: E-180
Earth Plates
EARTH PLATE - H Used to bond to rebar for lightning air termination on colum rebar, concrete columns, tunnels etc. Can be ThermexWeld exothermically welded to rebar. Can U-bolted on site. Copper alloy face with tapped holes. 70 mm2 green/yellow insulated cable. 500 mm long, factory welded to earth plate face.
EARTH PLATE Earth plate factory welded to rebar using LECTRO-TECH ThermexWELD
EARTH PLATE Earth plate fixed to rebar using LECTRO-TECH Rebar-Cable-Clamp Q-101
EARTH PLATE - V Used to bond to rebar for lightning air termination on colum rebar, concrete columns, tunnels etc. Can be ThermexWeld exothermically welded to rebar. Can U-bolted on site. Copper alloy face with tapped holes. 70 mm2 green/yellow insulated cable 500 mm long, factory welded to earth plate face
Manufactured from HC red copper bar, mounted on dumpy insulators with earth connection holes drilled. Also available in Tinned copper.
DISCONNECTING LINK
Manufactured from 25 x 3 mm HC red copper bar, mounted on dumpy insulators. Lugs 70mm2 Code: E-150 Flat 25 x 3mm Code: E-151 Also available in Tinned copper
EARTH BAR WITH TEST LINK
Manufactured from HC red copper bar, mounted on dumpy insulators with earth connection holes drilled. Also available in Tinned copper..
EARTH BAR - SPECIALS Manufactured from HC red copper bar, or tinned copper to customer drawings
EARTH PIT
Cast Iron earth pit with hinged lid. Sizes: L 325 x B 420 x H 150mm | Code: Q-200 L 225 x B 225 x H 100mm | Code: Q-202
EARTH PIT
Concrete earth pit and top. Sizes: Top 300 x 300mm Base 450 x 450mm Opening 140 x 140, H 500mm | Code: Q-201
CABLE MARKERS
Concrete. Sizes: Top 100 x100, Base 150 x 150 , H 320mm | Code: Q-210
Earth Receptacle
The generation of electrical static charges is a natural phenomenon. The charge is normally dissipated harmlessly to ground; however, an arc produced in the presence of flammable vapours is a hazardous condition. Aircraft must be effectively and securely grounded prior to performing maintenance, and when loading/off-loading are being performed. The earth receptacle must be adequately bonded to a permanent earthing system. The LECTRO-TECH Earth Receptacle has a 500mm tail that can be ThermexWELDed or clamped to the earth electrode system.
Manufactured from brass and HC copper with 70 mm2 copper earth wire tail of 500mm long.
Code : E-190
Earth Mats All LECTRO-TECH earth mats have ThermexWELD exothermically welded joints.
STANDARD EARTH MAT 1m x 1m x 1m x 2m tail x 250mm grid in 70mm2 BCEW. Code: E-100
STANDARD CROWFOOT EARTH 25mm x 3mm copper tape x 5m long joined to a 70mm2 BCEW tail 2m long. Code: E-101
EARTHING AND BONDING CONDUCTOR - KWENA KWENA conductor cable is a composite stranded cable made up of tinned copper wires and galvanised steel wires that are braided-interwoven to form the cable. KWENA can be used as earth bonding cable or jumper bonds where earth tails are above ground, visible and open to easy theft. The complex braided and interwoven wires of steel and copper make it very difficult to separate and is unattractive and uneconomical to copper thieves and scrap dealers. KWENA is available in "bare" or "insulated" in black or clear. KWENA has been tested by the SABS and Gerotek Test Facilities for electrical properties. Example: 70mm2 copper cable equivalent KWENA is "70". Drum length Approximately 290m. Short lengths available on request and depending on stock availability.
EARTHING AND BONDING CONDUCTOR - COMPOSITE COMPOSITE conductor cable is a composite stranded cable made up of tinned copper wires and galvanised steel wires that are rope layered to form the cable. COMPOSITE applications and benefits are the same as for Kwena. COMPOSITE is available in "bare" or "insulated" in black or clear.
ThermexWELD of KWENA and COMPOSITE KWENA and COMPOSITE conductors can be welded using ThermexWELD exothermic copper process for joining of cables. ThermexWELD can be used for joining both of these cables to Copper conductors and Steel structures. The ThermexWELD process generates high temperatures that melt the wires, resulting in a fused joint. This high temperature will cause some melting of the tin and galvanising of the wire strands. To prevent corrosion and or any galvanic reaction in wet or buried Kwena cable, the joint MUST be properly sealed. Denso Paste & Tape After welding the joint must be Denso Paste/Denso Tape wrapped. Alternatively a bitumen must be "worked" into the cable strands whilst the joint is still hot. Protective covering of the surface strands of the cable only is not sufficient.
Two different compounds are available, both are an easy to use compound that: - reduces soil resistivity, - improves earth electrode contact with soil, - improves grounding earth resistance, - traps moisture, - will not leach out over time. E-Mix and E-Mix Super Conductive have been tested by independent authorities.
-E-MIX
Resistivity 1.9 m Conductivity 5.2mS/m Cement included, ready to mix with water. Size: 25 kg | Bag = 0.03 m3 | Code: E-170
- E-MIX SUPER CONDUCTIVE
Resistivity 0.1 m Conductivity 100mS/m Conforms to EN 50164-7 & IEC 62561-7 Cement included, ready to mix with water. Size: 25 kg | Bag = 0.03 m3 | Code: E-172 EARTH RESISTANCE CALCULATOR:Contact us for a copy of our "E-Mix Earth Resistance Calculator" - for single vertical rod - for trench earth CALCULATES: - resistance "with" and "with-out" E-Mix - number of bags of E-Mix required
USER INSTRUCTIONS Mix the cement supplied in the bag with the E-Mix compound with water to give a slurry consistency.
Drilled hole-(70-100mm dia): Fill hole to approx. 50% of depth with E-Mix. Place earth rod in centre of hole. Fill the rest of the hole with E-Mix. Agitate rod to remove air-pockets.
Trench-(250-300mm wide): Add half the depth (25-30mm) of EMix to trench and allow to set so that earth conductor is supported. Place earth conductor on top of EMix in trench and add a further 2530mm of E-Mix. Allow E-Mix to semi-harden (24 hours depending on temperature) before backfilling trench. Compact backfill 48 hours later.