Professional Documents
Culture Documents
Paging Messages
1 Paging Type 1 1. 2 TMSI Combination 2. 1 TMSI & 1 IMSI Combination 3. 2 IMSI Combination 2 Paging Type 2 1. 2 TMSI & 1 IMSI Combination 2. 3 TMSI Combination 3 Paging Type 3 * Links are provided for every messages. To view the detailed L3 Messages click the messages.
Other L3 Messages
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 Channel Request for LU Location Update Request Location Update Accept Immediate Assignment Extended Disconnect due to No Circuits Disconnect Normal Cause Release Release Complete Channel Release Sync Channel Information Measurement Report Classmark Enquiry Classmark Change Channel Request for Call Re-establishment Immediate Assignment for Call Re-establishment CM Re-establishment Request CM Service Reject CM Service Accept Cell Broadcast Page Channel Mode Modify Channel Mode Modify Acknowledge
Links are provided for ry messages. To view the ailed L3 Messages click the messages.
Note: This is just a tutorial material for Layer 3 messaging and call flow. These contains messages which we encounter in normal RF scenarios, All the messages specified in GSM TS 4.08 is not covered. All the messages are taken from TEMS 4.1.1 version.
n.N @adacellworks.com m
Note: In this presentation the BTS & BSC is considered together as BSS part.
MS
Channel Request Immediate Assignment CM Sevice Request
BSS
Complete Layer 3 Info Authentication Request Authentication Response Cipher Mode CMD Ciphering Mode Command Cipher Mode Complete Cipher Mode Complete Setup Identity Request Identity Response Call Proceeding Assignment Request Assignment Command Assignment Complete Assignment Complete
MS
BSS
Roaming Number
Initial Address Message (IA Paging Command Paging Channel Request Immediate Assignment Paging Response Complete Layer 3 Info Cipher Mode CMD Ciphering Mode Command Ciphering Mode Complete Cipher Mode Complete Identity Request Identity Response Setup Call Confirmed Assignment Request Assignment Command Assignment Complete Assignment Complete Alerting Connect Connect Acknowledge
MS
Channel Request Immediate Assignment Location Update Request
BSS
Authentication Para Authentication Request Authentication Response Update Location Insert Subsciber data Sub data insertion acc Location Update Accept TMSI Realloc Command TMSI Realloc Complete Location Update Accept
HLR
PSTN
HLR
Send Routing Info
PSTN
HLR
old VLR
Brief Idea: Generally 3 types of Paging message 1. Paging Message Type 1 Contains Paging for Max 2 mobiles
2. Paging Message Type 2 Contains Paging message for 3 mo 3. Paging Message Type 3 Contains only 4 TMSI's.
Generally 3 types of Paging messages. Message Type 1 Contains Paging for Max 2 mobiles, with IMSI or TMSI
Message Type 2 Contains Paging message for 3 mobiles. 1 IMSI and the other 2 or 1 TMSI
Note: This message normally for the Cell channel Info frequencies allocated for the particular cell. In hop frequencies in the MAL list along with the BCCH f indicate the TCH & BCCH frequencies.
Note: This message gives the information about the ne Will only gives the BCCH of the neighbors defined allows the mobile to restrict the neighbors to be se
Note: This message gives the information CBCH. Along with the other cell leve etc..
This message gives the information CBCH. Along with the other cell leve etc..
Note: This message gives the informatio mode. Will only gives the BCCH of th
sage normally for the Cell channel Informations. This will give the no of allocated for the particular cell. In hopping case this will indicate the in the MAL list along with the BCCH frequency. In non hopping case will TCH & BCCH frequencies.
sage gives the information about the neighbor frequencies in the idle mode. ves the BCCH of the neighbors defined. And the NCC permitted parameter mobile to restrict the neighbors to be sent in the measurement report.
This message gives the information about the CBCH for the mobile to decode the CBCH. Along with the other cell level details like LAC, RACH control parameters etc..
This message gives the information about the CBCH for the mobile to decode the CBCH. Along with the other cell level details like LAC, RACH control parameters etc..
This message gives the information about the neighbor frequencies in the dedicated mode. Will only gives the BCCH of the neighbors defined.
1. Channel Request
go back
2. Immediate Assignment
go back
3. CM Service Request
go back
4.Authentication Request
go back
5. Authentication Response
go back
go back
go back
8. Setup
go back
9. Identity Request
go back
go back
go back
go back
go back
14. Alerting
go back
15. Connect
go back
go back
Point 1 Once the Mobile sends the RACH it tries to decode all the AGCH information and waits for the Immediate assignment targeted to the particular mobile. It is being identified from the Establishment cause and Random reference.
In this message only the mobile forward the called number to the system.
1. Paging to the MS
go back
2. Channel Request
go back
3. Immediate Assignment
go back
4. Paging Response
go back
go back
go back
7. Identity Request
go back
8. Identity Response
go back
9. Setup
go back
go back
go back
go back
13. Alerting
go back
14. Connect
go back
go back
SMS Request
Measurement Report 1
Measurement Report 2
Measurement Report 3
Measurement Report 4
Measurement Report 5
Measurement Report 6
Measurement Report 7
Measurement Report 8
Measurement Report 9
Measurement Report 10
Measurement Report 11
Measurement Report 12
Measurement Report 13
Measurement Report 14
Measurement Report 15
Handover Command
Handover Access
Physical Information
Handover Complete
Physical Information
Channel Request
Immediate Assignment
Authentication Request
Authentication Response
go back
go back
go back
go back
go back
go back
go back
go back
Note:
Release
Release Complete
Channel Release
Measurement Report
Classmark Enquiry
Classmark Change
CM Re-establishment Request
CM Service Reject
CM Service Accept
Note In dedicated mode or group transmit mode, higher layers can request the setting of the channel mode.The channel mode modify procedure allows the network to request the mobile station to set the channel mode for one channel. The channel mode covers the coding, decoding and transcoding mode used on the indicated channel.