Professional Documents
Culture Documents
True RMS.
VOLTAGE INPUTS: Four wires of a 415 Volts Electrical System. (Other configurations
available on request.)
CURRENT INPUTS: 5 Amp.C.T. Secondaries from three phases. (Other configuration
available on request.)
DISPLAY
LOAD RANGE
TECHNIAL SPECIFICATIONS
VOLTAGE INPUTS: Three/Four wires of a 110/415 Volts Electrical system.
(To be specified at the time of ordering)
CURRENT INPUTS: 1 or 5 Amp. C.T. secondary from two/three phases. (To be
Specified at the time of ordering).
DISPLAY: 8 digit Liquid Crystal Display (LCD).
LOAD RANGE: 120% to 0.4% of rated CT primary.
TECHNICAL SPECIFICATION
VOLTAGE INPUTS
CURRENT INPUT
DISPLAY
LOAD RANGE
OPERATING P.F.
TECHNICAL SPECIFICATION
VOLTAGE INPUTS
: 4-wires of a 415 volt electrical system/3-wires from HT PT.
CURRENT INPUTS
:1/5 Amp.C.T. secondaries from three / two phases.
PARAMETER DISPLAYED: Three voltages, three currents, power factor, KVA,
KW,KVAr, KWh KVAh, KVArh, Hz, Demand & Maximum
Demand.
DISPLAY
: 16 x 1 LC display..
RESOLUTION: Phase voltages: 1 volt,
Phase current: 0.1Amp
Power Factor : 0.001unit
KVA,KW& KVAr: 0.01 unit
KVAh, KVARh & KWh: 0.01 unit
LOAD RANGE
: 120 % To 0.4% of rated CT primary.
OPERATING P.F
: ZERO LAG to UNITY to ZERO LEAD.
SIZE
Bezel: 96 x 96 MM
APFCR
TECHNICAL SPECIFICATIONS
*Measurement system : The PF is measured for any one phase from the voltage
senses between Phase and neutral and current in the
same phase, using Digital Signal Processing (DSP)
Methods.
*Supply Voltage :
230 VAC, 50 Hz nominal between phase and neutral.
*Supply Voltage Range : 80 to 270 VAC.
*Current:
5 Amps from CT secondary.
*Output switching capacity : 5 Amps @ 230 VAC resistive load.
*No. of stages :
Standard 6, 8, 10, 12 and 16 stages.
*Target PF setting :
From 0.8 (Lag) to unity in PF mode, and 0.8
(Lead) in VAR mode.
*Reconnection Time Delay : Settable at site, from 5 seconds to 120 seconds.
*Minimum Current :
5% of rated CT primary in PF mode, and 1.0% in
case of VAR mode.
*Mounting :
Flush mounted using clamps.
*Size :
144 x 144 mm bazel, 138 x 138 mm cutout size.
*Depth of Installation:
95 mm including terminal
GLOBLIN
ELECTRICAL LOAD MANAGER
Measurement, Control, Data, Logging, Communication
1) Displays more than 20 Parameters.
2) Large 20 x 4 Backlit LC Display.
3) Four Relay contacts, individually field programmable, for alarm parameter as
well a on/off values.
4) RS-485 MODBUS-TRU Connectivity.
5) RS-232 port.
6) On board 32 KB of non-volatile memory. On board data logging with field
programmable log duration.
7) CT / PT ratio field programmable.
8) Odd Harmonic Analysis up to 15th for all voltages and currents, including THD.
The digital power meter GOBLIN is a micro-controller based unit which not only
measures a host of electrical Parameters to display them on a 20 x 4 backlit LCD, but
also acts as a comprehensive load managing devised due to its four numbers of output
relay contacts. These outputs are individually field programmable for both the
parameter on which to generate alarm as well as the values on which to active alarm
and deactive it. In addition to this flexibility in term of load management, the meter
has serial ports: RS232C and RS485 as standard feature. The protocols supported
are MODBUS RTU for RS485 multi-drop systems and a proprietary TRINITY-1U
protocol for downloading logged data on a point-to-point basis.
The unit is meant for use in three phase four wire/ three wire systems. In three
phase four wire systems, it requires Four wires from R, Y, B & N in addition to six
wires from the three current transformers mounted on the three Phase. It thus the
three wattmeter method to arrive at the system KVA and KW. On the other hand, for
use in three wire system, it requires three phases from the PT secondary (usually 110
V AC ) and only four wires from the current teansformer secondaries of two phases.
The KVA and KW are calculated by the two wattmeter method.
The load manager GOBLIN, is a versatile meter, with all the features need to
implement a robust electrical load Management system. It can be configured to suit
most control and communication needs. This is achieved by making as many parameters
field programmable, as possible.
TECHNICAL SPECIFICATIONS
SUPPLY
CT CONNECTION
PT & CT RATIO
DISPLAY
PARAMETER DISPLAYED
ACCURACY
: Class 1.0
MEASUREMENT RANGE
AMPS
LOGGING DURATION
COMMUNICATION PORTS
COMMUNICATION PROTOCOLS
SIZE
DEPTH OF INSTALLATION
: 90 mm.max.
OPERATING TEMP.
: 0 cel. To 50 cel.
REF: Q/POWER/FEB/07
DT: 01/03/07
(VAF/ENTITY/ENTITY+/POWERPRO-XT/APFCR/GLOBLIN)
R/S:SIR.
THANKING YOU VERY MUCH FOR ENQUIRY FOR SUBJECT ITEMS AS DESIRED BY YOU,WE HEREBY
SUBMIT OUR FIRM OFFER FOR THE SAME AS BELOW.
SR
DESCRIPTION OF ITEM
MODEL
QTY
RATE/UNIT
VAF
01
2610=00
01
3960=00
01
5490=00
01
13500=00
01
18000=00
01
27270=00
LED DISPLAY
ENTITY
LCD DISPLAY
ENTITY +
LCD DISPLAY
POWER
PRO-XT
LCD DISPLAY
APFCR
LCD DISPLAY
GLOBLIN
LCD DISPLAY