Innoveam was established to provide high delity 3D simulation and consultancy
services. With our core competency in Computational Fluid Dynamics, Innoveam
serves the oil and gas industry in Malaysia and South East Asia in nding critical solutions in designing oil and gas facilities and equipment. OIL & GAS SIMULATION Innoveam was established to provide high delity 3D simulation and consultancy services. With our core competency in Computational Fluid Dynamics, Innoveam serves the oil and gas industry in Malaysia and South East Asia in nding critical solutions in designing oil and gas facilities and equipment. OIL & GAS SIMULATION Computational Fluid Dynamics (CFD) is a simulation tool that solves uid ow, heat transfer, and other related phenomenon (mass transfer, combustion and reaction, and multiphase ows) using numerical equations. CFD is used as a "Virtual Experiment" which allows the assessment of full three dimensional processes and equipment on the computer prior to any CAPEX investment. Our core strength is the application of Computational Fluid Dynamics in solving engineering design problems and providing optimised and trustworthy solutions to our clients. Our approach to applying CFD services can be divided into: APPLIED CFD Typical objectives for design assessment include design validation, suitable for engineering companies with an approved design that requires validation. This approach can be done via single one-of studies or through multiple case and what-if scenarios, and doesnt include any redesign. Design Assesment & Recommendation The main objective for full optimisation studies is to simply optimise the design, suitable for engineering companies which are in the midst of the design stage and intends to optimise the design in terms of performance, time and cost. Our approach can be summarised based on the following sequence. Full Optimisation Studies # 2 DESIGN ASSESSMENT DESIGN RECOMMENDATION IMPLEMENT & RE-EVALUATE FINAL OPTIMISED DESIGN MULTIPLE ITERATIONS Our capabilities for CFD simulation for the Oil and Gas industry include the following: SIMULATION AT THE HEART OF OUR SERVICE CFD SAFETY STUDIES MECHANICAL / HVAC EQUIPMENT DESIGN Proof of concept Design optimisation Debottlenecking Sloshing & bafe optimisation Sand management & erosion Fire & blast analysis Gas dispersion Risk assessments Fire & gas mapping Thermal plume studies Wind/wave loading HVAC optimisation Separators are one of the key equipment for oil and gas facilities and involve complex ow structures involving multiphase ows of oil, water and gas. 3D CFD simulation provides a powerful tool to predict and design separators for proof of concept, separation performance quantication for process guarantees, capacity identication and debottlenecking. OIL & GAS CFD SIMULATION MECHANICAL/HVAC SAFETY STUDIES SAFETY STUDIES PROCESS SIMULATION/EQUIPMENT DESIGN Separator Design & Debottlenecking 3D CFD Simulation can be used to model the are combustion and detailed radiation intensities in 3-dimensional space for processing facilities, which can be highly afected by the detailed interaction between cross winds and localised turbulent structures. Under snuf-out conditions, CFD can accurately predict the gas dispersion behaviour and ammability regions under various ambient conditions. This is particularly important for gas with high H 2 S and CO 2 content, which may prove hazardous to personnel. Flare Radiation Assessment & Snuf-out Conditions 3D CFD simulation can be used to model the complex interaction between multiple thermal and momentum sources on board an ofshore facility. These can be exhaust stacks from power generators, air coolers and ares. The air ventilation can also be assessed, and be used to see suitable working conditions for personnel and inlet conditions for other equipment. Of particular importance is the helicopter landing conditions and the requirements of CAP437, which CFD can predict accurately. Major examples of 3D CFD simulation in Oil & Gas industry. Thermal Plume Studies and Ventilation Assessment Detailed consequence analyses of re and explosion scenarios for hydrocarbon facilities are important in order to cost efectively provide safety measures on site. Detailed 3D re simulation capture the important interaction between the combustion process and the complex geometries that the processing plant represents. This allows accurate prediction of re dimensions and radiation intensities, which is vital for optimum design of re protection, as well as escape and evacuation. 3D simulation of gas explosions in the congested areas on these processing facilities accurately predicts blast overpressures, which are vital in identifying blast wall requirements and locations. Fire & Explosion Studies for QRA Inputs # 1 MECHANICAL Vessels containing liquid are used extensively on mobile ofshore facilities, and are often subjected to 6-degrees of freedom motion due to the wave loadings. 3D CFD simulation allows the cost efective prediction of the liquid levels and their displacement within the vessels. This is important to avoid any false HHLL or LLLL alarms, and to assist in optimum calming bafe designs. Vessel Sloshing Studies # 1 # 2 # 3 Sequence of explosion event for topside equipment. Vessel internal ow structures. Water droplet distribution in an oil-water seperator. # 1 # 1 # 5 # 2 # 3 # 4 KNOWLEDGEABLE INNOVATION Innoveam Sdn Bhd GTower Level 14-11, 199 Jalan Tun Razak, 50400 KualaLumpur, Malaysia T : +603 - 2168 1905 F : +603 - 2168 1824 http://www.innoveam.com Email : info@innoveam.com Innoveam Sdn Bhd GTower Level 14-11, 199 Jalan Tun Razak, 50400 KualaLumpur, Malaysia T : +603 - 2168 1905 F : +603 - 2168 1824 http://www.innoveam.com Email : info@innoveam.com