1. Bandwidth required for baseband signals in telephony is
a)0.3 to 3.4Khz b)3.5 to 7.7Khz c) upto 15Khz d)upto 20Khz
2. The image channel rejection in a super heterodyne receiver comes from a) IF stage only b) RFstage only c)detector and RFstages only d) detector,RF and IF stages
3. The purpose of peak clipper circuits in radio transmitters is to a) reduce bandwidth b)increase bandwidth c)prevent over modulation d)regulate oscillator input voltage
4.In super heterodyne receiver,the frequency of the local oscillator is a)equal to that of incoming signal b)higher than that of incoming signal c) slightly less than that of incoming signal d) half that of incoming signal
5.A carrier is simultaneously amplitude modulated by two sine waves with modulation indices of 0.3 and 0.4.If the modulated power is 10kw.What is the total modulated power? a)12.5kW b)10Kw c)10.125kW d)10.5Kw
6.Which of the following demodulators can be used for demodulating the signal X(t)=5(1+2 cos2000t) cos2000t a)envelope detector b)square-law demodulator c)synchronous demodulator d)all the above
7. A super heterodyne radio receiver with an intermediate frequency of 455khz is tuned to a station operating at 1200khz.The associated image frequency is_____ a)2000khz b)2100khz c)2200khz d)2110khz
8.A 10MHZ carrier is frequency modulated by a sinusoidal signal of 500HZ,the maximum frequency deviation being 50KHZ.The bandwidth required, as given by the Carsons rule is a)100KHZ b)110KHZ c)111KHZ d)101KHZ
9.V(t)=5*cos(106t)-sin(103t) sin(106t)+ represents a)DSB-SC signal b)AM signal c) SSB upper side band signal d) Narrow band FM signal
10. Inreased pulse width in the flat-top sampling leads to a)attenuation of high frequencies in reproduction b) attenuation of low frequencies in reproduction c) greater aliasing errors in reproduction d)no harmful effects in reproduction
11.A 1KHZ signal is flat-top sampled at the rate of 1800 samples per second and the samples are applied to an ideal rectangular LPF with cut-off frequency of 1100HZ,then the output of the filter contains a)only 800HZ component b) 800HZ and 900HZ components c) 800HZ and 1000Hz components d) 800HZ, 900HZ and 1000Hzc omponents
12.Flat-top sampling of low pass signals a)gives rise to aperture effect b)implies oversampling c)leads to aliasing d)introduces delay distortion
13.A DSB-SC signal is generated using the carrier cos(w c t+) and modulating signal x(t).The envelope of the DSB-SC signal is a) x(t) b) Ix(t)I c)only positive portion of x(t). d) x(t) cos 14.A modulated signal is given by s(t)=m 1 (t) cos (2f c t)+m 2 (t) sin(2f c t) where the baseband signal s m 1 (t) and m 2 (t) have bandwidths of 10khz and 15 khz respectively. The bandwidth of the amplitude modulated signal, in khz is a)10 b)15 c)25 d)30
15. A modulated signal is given by s(t)=e -at cos[(w c +w)t+ u(t), where a,w c and w are positive constants and w c >>w.The complex envelope of s(t) is given by a)e -at exp(j(w c +w)t) u(t) b) e -at exp(jwt) u(t) c) exp(jwt) u(t) d)exp(j(w c +w)t)
16.A band limited signal is sampled at the Nyquist rate.The signal can be recovered by passing the samples through a)an RC filter b)an envelope detector c)a PLL d)an ideal low pass filter with the appropriate bandwidth.
17.A 1MHZ sinusoidal carrier is amplitude modulated by a symmetrical square wave of period 100sec.Which of the following frequencies will not be present in the modulated signal a)990khz b)1010khz c)1020khz d)1030khz
18.The input to a coherent detector is DSB-SC signal plus noise.The noise at the detector output is a)in-phase component b)quadrature component c)zero d)the envelope
19.An AM signal is detected using an envelope detector .The carrier and modulating signal frequencies are 1MHz and 2kHz respectively. An appropriate value for the time constant of the envelope detector is a)500sec b)20sec c)0.2sec d)1sec
20.An AM signal and a narrow band FM signal with identical carriers ,modulating signals and modulation indices of 0.1 are added together .The resultant signal can be closely approximated by a)broadband FM b)SSB with carrier c)DSB-SC d) SSB without carrier
21.Which of the following analog modulation scheme requires the minimum transmitted power nad minimum channel width? a)VSB b)DSB-SC c)SSB d)AM
22.The power in the signal s(t)=8 cos(20t-/2)+4 sin (15t) is a)40w b)41w c)42w d)82w
23.For a message signal m(t)=cos(2f m t) and carrier of frequency f c , which of the following represents a single side-band signal? a) cos(2f m t) cos(2f c t) b) cos(2f c t) c) cos(2(f c+ f m )t) d)(1+cos(2f m t)) cos(2f c t)
24.A band-limited signal with a maximum frequency of 5 kHz is to be sampled. According to the sampling theorem, the sampling frequency which is not valid is a)5 kHz b) 12 kHz c) 15 kHz d) 20 kHz
25. Consider the amplitude modulated (AM) signal A c cosw c t 2cosw c t coswt. For demodulating the signal using envelope detector, the minimum value of Ac should be a)2 b) 1 c) 0.5 d) 0 ANSWERS 1.a 2.c 3.c 4.b 5.a 6.d 7.d 8.d 9.d 10.a 11.b 12.a 13.b 14.c 15.c 16.d 17.c 18.c 19.b 20.b 21.c 22.a 23.c 24.c 25.a
3rd Generation Partnership Project Technical Specification Group Services and System Aspects Functional Stage 2 Description of Location Services in UMTS, (3G TS 23.171 Version 1.1.0)