Professional Documents
Culture Documents
A Fabreeka Company
2215 Lyons Road
Miamisburg, Ohio 45342-4465
Phone: 937-438-1100
Fax: 937-438-2190
Email: tpc@novibes.com
Website: www.novibes.com
Table of Contents
Technical Section ........................................................................
Elastomer Information.................................................................
Engineering Analysis....................................................................
Company Contact Information ....................................................
2-9
10
11
105
58-59
50-53
60-63
100-102
48-49
70
54-55
22-26
98
97
34-37
103
93
28-29
19
18
99
20-21
56-57
40-41
71
32-33
30-31
16-17
14-15
104
12-13
64-67
72
68-69
94-96
73
27
38-39
74-92
42-47
Technical Section
Technical Section
Vibration
Vibration/Shock Terminology
ResonanceA condition that occurs when the forcing frequency coincides with
the natural frequency of a suspension system. Avoid this at all costs.
Natural Frequency is the frequency of vibration that will occur if a system is disturbed
from its normal position and allowed to
vibrate freely. For our purposes the natural
frequency can be defined as a function
of mass and stiness or spring rate. If the
spring rate is linear, the load vs. deflection curve is a straight line (Figure 3). For
instance, a load of 100 pounds will cause a
deflection of .20 inches. This spring will have
a stiness of:
=
100
=
= 500
. 20
1
2
K
Figure 1
W
K
Figure 2
Figure 3
Technical Section
If the frequency of the input that we are
isolating from (the forcing frequency) is defined as ff , it can be shown that if the spring
has been selected so that:
Technical Section
> 2
However, if:
< 2
.15
.2
TRANSMISSIBILITY (T)
.5
1.0
DAMPING
FACTOR (d)
0.1
0.01
1 1.414
0.1
. 100
10
Figure 4
Typical Damping Factors
Material
Natural Rubber
Neoprene
Felt and Cork
Butyl
High Damped Silicone
Friction Damped Spring
d
.05
.05
.06
.10
.15+
.30+
Figure 5
The three types of damping usually encountered are friction (Coulomb), hysteretic and
viscous.
Friction damping is characterized by sliding
surfaces. Hysteretic damping is the damping
that is inherent in a material. Viscous (or
fluid) damping is characterized by proportional relationships between forces and
velocities, e.g. an object moving through a
liquid.
=
1
+1
EXAMPLE
A unit with a weight of 800 pounds is to be
mounted on four isolators. The center of
gravity is located at the center of the unit.
The forcing frequency is 30 Hz and 80% isolation, or a transmissibility of .20 is desired.
With four isolators, the load supported by
each will be 200 pounds. If the units center
of gravity is eccentric, a load distribution
analysis must be made to determine the
load at each mounting point.
Loads versus natural frequency curves are
available for most Tech Products isolators.
Often several isolators can be selected using
these curves. The load versus frequency
curves for the 515 Series may result in a
proper isolator selection; however, there
are always other conditions to consider.
These may be: shock requirements, available space, mounting orientation or environmental conditions.
First the required system natural frequency
is determined:
30
=
=
= 12.2
1
1
+
1
+1
. 20
Next, choose a load versus natural frequency curve where the supported weight
is about in the middle of the load range. If,
after the calculations are made, desirable
results are not obtained, go to the curves of
the next larger or smaller mount and repeat
the calculations.
Figures 6 and 7 show the curves for a typical
mount that has been selected for this application. Draw a horizontal line across Figure
7 at 200 pounds on the load axis. Then draw
a vertical line across Figure 7 from 12.2 Hz
on the natural frequency axis. The intersection of the two lines is slightly to the left of
curve -4 on Figure 7.
Technical Section
Shortcuts
The preceeding transmissibility equation is
graphically produced in Figure 8.
600
-3
500
-2
400
-1
600
NC
500
SO
NA
400
300
VIBRATION
AMPLIFICATION
REGION
200
100
100
1000
Figure 8
300
200
100
40
0
0
0.05
0.1
0.15
0.2
20
0.25
Figure 6
9
7
1000
800
600
= 3.13
= .
400
LOADS (POUNDS)
200
1
0.01
-5
-4
-3
-2
90
70
30
10
5
10
12.5
0.1
Figure 9
-1
50
70
60
80
90
95
700
-5
-4
96
1000
900
800
800
700
97
98
99
IS
OL
AT
IO
N
99
.5
2000
RE
If load vs. frequency curves are not available, then Figure 9 can be used to help
select an isolator. The desired natural
frequency is determined as in the example
previously discussed (12.2 Hz). Draw a horizontal line from 12.2 Hz on the natural frequency axis to the intersection of the dark
diagonal line. Draw a vertical line down to
the intersection of the static deflection axis.
This point, approximately .065 inches, is the
static deflection required of the isolator to
produce a natural frequency of 12.2 Hz.
Load deflection curves can now be used to
determine what isolator will produce .065
inches deflection at the given load.
Technical Section
20
FREQUENCY (Hz)
Figure 7
6
Technical Section
Technical Section
Shock
EXAMPLE
A piece of equipment is subjected to a 24inch (h) free-fall drop. It is known that the
equipment cannot withstand more than 25
gs, i.e. the fragility level is 25 gs. The
equipment weighs 400 pounds.
61.4
The associated dynamic deflection (d) can
be determined by:
=
2
10, =
()
()
where:
= 2 1
= 2 ( )
= 2 2 ( )
136
=
=
= 1.92
2 2(11.3)
Now calculate the required dynamic stiness (K) for the system.
= 3.13
=
2
2
0 0
= 0 0
( ) (11.3)
=
(3.13)2
(3.13)2
= 5213 /
2 0 0
Figure 10
2 0 0
Engineering Analysis
Elastomer Properties
Tech Products oers complete engineering analysis for all types of applications. The
information below is required for a full six degree of freedom analysis of engine isolation
applications. For other applicaitons, please contact Tech Products at engr@novibes.com.
Forms are also available at http://www.novibes.com/Services.
Tech Products oers a variety of standard elastomers for all types of isolators. Proper
selection of elastomer based on mechanical properties, temperature range, and chemical
resistance is crucial to optimizing the life of the isolators. Following is basic information for
Tech Products standard elastomer options. Other elastomers and custom compounds are
also available.
Neoprene:
Adhesion to Metal:
Tensile Strength:
Compression Set:
Damping Factor (C/Cc):
Operating Temperature:
Oil Resistance:
Ozone Resistance:
Weather / Sunlight Aging:
Heat Aging:
Excellent
Excellent
Fair
0.05
-20 to 180OF
Good
Good
Good
Good
Butyl:
Adhesion to Metal:
Tensile Strength:
Compression Set:
Damping Factor (C/Cc):
Operating Temperature:
Oil Resistance:
Ozone Resistance:
Weather / Sunlight Aging:
Heat Aging:
Good
Excellent
Fair
0.15
-20 to 200OF
Fair
Good
Good
Good
Natural Rubber:
Adhesion to Metal:
Tensile Strength:
Compression Set:
Damping Factor (C/Cc):
Operating Temperature:
Oil Resistance:
Ozone Resistance:
Weather / Sunlight Aging:
Heat Aging:
Excellent
Excellent
Good
0.05
-20 to 180OF
Poor
Poor
Poor
Fair
Silicone:
Adhesion to Metal:
Tensile Strength:
Compression Set:
Damping Factor (C/Cc):
Operating Temperature:
Oil Resistance:
Ozone Resistance:
Weather / Sunlight Aging:
Heat Aging:
Good
Good
Fair
0.05 - 0.08
-80 to 400OF
Fair
Excellent
Excellent
Excellent
Nitrile:
Adhesion to Metal:
Tensile Strength:
Compression Set:
Damping Factor (C/Cc):
Operating Temperature:
Oil Resistance:
Ozone Resistance:
Weather / Sunlight Aging:
Heat Aging:
Excellent
Excellent
Good
0.05
-20 to 180OF
Excellent
Fair
Fair
Good
Good
Good
Fair
0.15 - 0.20
-80 to 350OF
Fair
Excellent
Excellent
Excellent
Customer Information
Company
______________Contact____________________________
Phone
_____ Fax__________________Email______________________
Project Name___________________________________________________________
Engine Data
Engine Model & Manufacturer
Engine Operating Speed (rpm)
Engine Idle Speed (rpm)
Engine Weight with accessories (lb or Kg)
Engine Rated Power (Hp or KW)
Number of Cylinders
Stroke (Two or Four)
Output Torque (If Available) (N-m or ft-lb)
Make and Model of Power Take-Off Equipment*
Weight of Power Take-Off Equipment* (lb or Kg)
Mounting Location
*Reference the following drawings to fill out remaining data - Please note units
10
11
Pivotal Levelers
Pivotal Levelers
Color
Code
Max.
Load
(lbs)
50510 Green
350
Part
No.
equipment up to 8,000 lbs., providing stability, isolation and shock protection while
allowing complete portability. They permit
1/4 or more of leveling, depending on the
attachment hardware used.
Pivotal Levelers are made of bonded
neoprene/steel for long service life and
resistance to ozone and oils.
50520 White
700
50530 Green
500
50540 White
1000
50531 Green
500
50541 White
1000
50532 Green
500
50542 White
1000
50534 Green
3700
50544 White
8000
50535 Green
3700
50545 White
8000
50536 Green
3700
50546 White
8000
Configuration
Description
Thread
-13
-13
N/A
-13
N/A
-10
-10
Square, with
round hole and
hex nut; free to
rotate. *Available
in stainless steel.
Add -A to part number for 5 long epoxied stud and hex nut
12
13
Mounting Feet
Mounting Feet
Without Glide
With Glide
Part No.
1 3/8
DIA. MIN.
1/2-13 Thread
Without Glide
1/2-13 Thread
With Glide
Color Code
50601
50604
Yellow
40-135 lbs.
10-40 lbs.
50602
50605
Green
80-250
30-80
50603
50606
White
200-450
70-180
0.1-0.3
0.08-0.2
Without Glide
With Glide
With Glide
Part No.
Part No.
1/2-13 Thread
With Glide
Color Code
50607
50617
Yellow
50608
50618
Green
90-450
60-300
50609
50619
White
225-1000
150-600
0.05-0.2
0.05-0.2
1 3/8
DIA. MIN.
3/8-16 Thread
With Glide
Color Code
50553
50563
Yellow
50555
50565
Green
75-250
20-65
50557
50567
White
150-400
50-130
0.1-0.3
0.05-0.25
30-125 lbs.
6-35 lbs.
14
1 3/8
DIA. MIN.
1/2-13 Thread
Without Glide
Point Load Range:
3/8-16 Thread
Without Glide
15
60-250 lbs.
20-80 lbs.
Whenever you need to protect heavy production equipment from shock and vibration, this rugged series of Leveling Mounts
will do the job to your full satisfaction.
Their no-walk, no-creep performance lets
you place your equipment wherever you
wish without bolting it to the floor and to
move it easily without re-anchoring or reshimming.
Even when immersed in oil, water or other
hazards, the high strength steel housing
and neoprene base resist failure for years of
daily punishment.
We oer six standard load ranges to closely
match your weight and dimensional requirements. Punch presses, milling machines,
injection molding equipment, lathes,
compressors, mixersany equipment that
generates motion internally or is aected
by external vibration can be economically
mounted for top performance plus complete portability.
Leveling is simple and quick with internal
adjustment capability up to inch above
loaded height, just by a few turns of the leveling bolt. Then the locknut is tightened on
the machine foot for a permanent, precise
mount.
Easy Leveling
No Special Foundations
Part No.
Min. Load
(lbs.)
Max. Load
(lbs.)
Bolt Size x
Length (in.)
D (In.)
Static Height
(in.)
52220
30
150
3/8-16 x 3
3.13
1.50
52221
55
250
3/8-16 x 3
3.13
1.50
52221-1
100
500
3/8-24 x 3
3.13
1.50
52222
100
500
3/8-16 x 3
3.13
1.50
52223*
300
1000
1/2-13 x 5
4.75
1.50
52224
300
1000
1/2-13 x 5
4.75
1.50
52225*
500
4500
3/4-10 x 5
6.25
1.63
52226
500
4500
3/4-10 x 5
6.25
1.63
52227*
4000
13000
1-14 x 8
2.50
Applications:
Punch Presses
Lathes
Grinders
Jig Borers
Screw Machines
Milling, Machines
Brakes
Four Slides
52229*
4000
13000
1-14 x 8
2.25
52231
4000
13000
3/4-10 x 4
2.25
52232
4000
13000
3/4-10 x 8
2.25
Bolt Size x
Length (mm)
D (mm)
Static Height
(mm.)
Metric Series
Part No.
52221-1-M10
45
230
M10x1.5 x 80
80
38
52224-M12
135
450
M12x1.75 x 130
120
38
52226-M20
230
2040
M20x2.5 x 130
160
41
52229-M24
1815
5900
M24x3.0 x 180
230
57
52248-M30*
3500
11500
M30x3.5 x 200
315
70
Normally Supplied with hex head bolt. (*) indicates square head bolts
16
17
Fabcel Levelers
Elastomer Springs
Part
No.
Max.
Load
(lbs.)
71612
0.63
0.25
0.47
72
71616
0.63
0.25
0.63
77
71620
0.63
0.25
0.79
80
71625
0.63
0.25
1.00
83
72016
0.79
0.33
0.63
133
72020
0.79
0.33
0.79
132
72025
0.79
0.33
1.00
133
72032
0.79
0.33
1.25
126
72520
1.00
0.41
0.79
215
72525
1.00
0.41
1.00
209
72532
1.00
0.41
1.25
229
72540
1.00
0.41
1.56
241
73232
1.25
0.53
1.25
451
73240
1.25
0.53
1.56
471
Model Number
Q35
Q75
Q150
T35
T75
T150
73250
1.25
0.53
2.00
456
Bolt Diameter
1/4-20
1/4-20
1/4-20
3/8-16
3/8-16
3/8-16
73263
1.25
0.53
2.50
452
1.31
1.31
1.31
1.50
1.50
1.50
74032
1.56
0.53
1.25
783
1.50
1.50
1.50
1.50
1.50
1.50
74040
1.56
0.53
1.56
816
1.38
1.38
1.38
1.38
1.38
1.38
74050
1.56
0.53
2.00
804
2.06
2.06
2.06
2.38
2.38
2.38
74063
1.56
0.53
2.50
815
35
75
150
35
75
150
74080
1.56
0.53
3.15
830
75063
2.00
0.66
2.50
1297
76363
2.50
0.66
2.50
2000
Model Number
TE75
TE150
TE300
LD75
LD150
HD300
HD450
78063
3.15
0.83
2.50
4000
Bolt Diameter
3/8-16
3/8-16
3/8-16
1/2-13
1/2-13
1/2-13
1/2-13
79063
3.94
0.83
2.50
5631
1.63
1.63
1.63
1.69
1.69
1.69
1.69
2.13
2.13
2.13
2.13
2.13
2.13
2.13
2.56
2.56
2.56
2.69
2.69
2.69
2.88
75
150
300
75
150
300
450
18
19
Part No.
Color
Code
51700-1
50
Yellow/Gold
51700-3
90
Red/Gold
51700-5
150
Green/Gold
51700-7
215
Blue/Gold
51700-9
300
White/Gold
51641-2
100
Yellow/Gold
51641-4
155
Red/Gold
230
Green/Gold
51641-6
51641 Series
51641 SERIES AXIAL LOAD VS. DEFLECTION
51641-8
320
Blue/Gold
51641-10
420
White/Gold
51716-2
120
Yellow/Gold
51716-4
185
Red/Gold
51716-6
250
Green/Gold
51716-8
400
Blue/Gold
51716-10
550
White/Gold
51716 Series
51716 SERIES AXIAL LOAD VS. DEFLECTION
1000
-10
800
-8
LOAD (LB.)
600
-6
400
-4
-2
200
INSTALLATION
0
20
21
0.05
0.1
0.15
DEFLECTION (IN.)
0.2
0.25
Compression Mounts
Standard Deflection
Compression Mounts
Part No.
Color
Code
Max.
Load
(lbs)
Max.
Deflection
(in)
L
(in)
W
(in)
H
(in)
52501
52502
52503
52504
Blue
Black
Red
Green
35
45
70
120
0.20
52521
52522
52523
52524
52525
Blue
Black
Red
Green
Gray
135
170
240
380
550
0.25
-16
52541
52542
52543
52544
Black
Red
Green
Gray
250
525
750
1100
0.25
-13
52561-2
52562-2
52563-2
52564-2
Black
Red
Green
Gray
1500
2250
3000
4000
0.25
A
(in)
/-18
-13
C
(in)
D
(in)
Double Deflection
E
(in)
Part No.
Color
Code
Max.
Load
(lbs)
Max.
Deflection
(in)
L
(in)
W
(in)
H
(in)
A
(in)
C
(in)
D
(in)
E
(in)
52511
52512
52513
52514
Blue
Black
Red
Green
35
45
70
120
0.40
/-18
52531
52532
52533
52534
52535
Blue
Black
Red
Green
Gray
135
170
240
380
550
0.50
-16
52551
52552
52553
52554
Black
Red
Green
Gray
250
525
750
1100
0.50
-13
52571-2
52572-2
52573-2
52574-2
Black
Red
Green
Gray
1500
2250
3000
4000
0.50
-13
22
23
Compression Mounts
Yellow
Compression Mounts
Load Range
(lbs.)
W
(in.)
Part
No.
Color Code
Load Range
(lbs.)
W
(in.)
20-60
52164
Red
70-200
52161
Red
40-100
52165
Green
140-280
52162
Green
60-150
52166
Blue
240-500
52163
Blue
80-200
52167
White
450-700
24
Heavy Duty
This compression mount design is for
applications under heavy industrial
machinery requiring ecient vibration,
noise, and shock isolation. Typical applications include pumps, compressors,
and generators.
Part No.
25
Color Code
Part No.
Color Code
52171
Red
700
52135
White
1500
52172
Green
1000
52136
Green
1000
52173
Blue
1500
52137
Red
700
52174
White
2500
Spring Mounts
Tech Products spring mounts with aluminum housings are durable enough to handle most
of the applications where steel housings are used. The aluminum housing is more weather
resistant and lighter. The cast aluminum allows for higher quality thread integrity. The ribbed
neoprene pad provides a non-skid base, and neoprene stabilizer pads are included in the
housing to control lateral motion. All aluminum housed mounts include one spring with load
ratings as high as 1300 lbs.
Features:
Low Maintenance
Part
No.
Spring
Color
Max.
Load
(lbs)
Static
Defl.
52811
Purple
40
1.3
52812
Blue
60
1.3
52813
Orange
100
1.3
52814
Brown
165
1.2
52815
Black
260
1.0
52816
Yellow
370
0.8
52817
Red
450
0.5
52818
Green
700
0.5
1.36
Part No.
Color Code
52841
Pink
85
52054-1
Green
1500
52842
Black
115
1.31
52843
Blue
170
1.28
52844
Yellow
225
1.26
52845
Brown
325
1.23
52846
Red
450
1.22
52847
Purple
600
1.17
52848
Orange
750
1.06
52849
Green
900
1.02
52850
Gray
1100
0.83
52851
White
1300
0.74
52054-2
Blue
2000
52054-3
White
3000
52054-4
Purple
4400
26
27
5.69
2.25
3.88
4.00
5.00
-16
3.00
0.44
0.31
7.75
2.63
5.06
5.13
6.56
-13
3.50
0.56
0.38
Dome Mounts
Dome Mounts
52545 COMPRESSION LOAD VS DEFLECTION
1600
-4
1400
LOAD (LB.)
1200
1000
-3
800
-2
600
400
-1
200
0.02
0.04
0.06
0.08
0.1
0.14
0.12
DEFLECTION (IN.)
(2X) 0.53
0.12
-4
1800
1600
Part No.
Color
Code
Max. Load
(lbs.)
Spring Rate
(lbs/in.)
52545-1
Red
375
3000
52545-2
Green
800
6400
52545-3
Blue
925
7400
52545-4
White
1425
11500
52546-1
Red
525
4150
52546-2
Green
1000
8300
52546-3
Blue
1250
10000
52546-4
White
1950
15600
LOAD (LB.)
1400
-3
1200
-2
1000
800
600
-1
400
5.38
3.25
4.12
200
0.53
0
0
0.02
0.04
0.06
0.08
DEFLECTION (IN.)
6.25
3.94
5.00
0.78
28
29
0.1
0.12
0.14
LOW FREQUENCY
MOUNT
FLOOR
Part
No.
Color
Code
Min.
Max.
Approx.
Approx.
Load
Load
Defl.
Defl.
(lbs)
(lbs)
Part
No.
50
0.1
400
0.9
61060 Yellow
150
0.1
1800
61505 Green
100
0.1
1100
0.9
61062 Green
500
0.15
3100
0.9
61507 White
250
0.1
2600
0.9
0.2
4700
0.8
1600
61507
61505
LOAD (LB.)
1200
800
600
61503
2000
1000
500
0.2
0.4
0.6
0.8
61060
1500
200
DEFLECTION (IN.)
31
2500
400
61062
3000
1000
61064
3500
1400
30
Min.
Max.
Approx.
Approx.
Load
Load
Defl.
Defl.
(lbs)
(lbs)
Color
Code
61503 Yellow
LOAD (LB.)
0.2
0.4
0.6
DEFLECTION (IN.)
0.8
Isosphere Mounts
Isosphere Mounts
Color
Part No.
Code
61549-2 Black
Max.
Dynamic
Dia. @ Height
Max
Static Static Thread
Static
Spring
Max. @ Max.
Dynamic
Dia. Height
Size
Load
Rate
Static
Static
Load (lbs)
(in)
(in) (Option 1)
(lbs)
(lbs/in)
Load (in) Load (in)
500
2000
1500
61549-3 Green
750
3000
2000
61549-4
Red
1000
4000
3000
61549-5
Gray
2000
8000
5500
61550-4
Gray
10,000
40,000
16,000
3.70
3.88
-18
4.50
2.30
8.50
8.69
1-12
10.50
5.00
32
33
Cupmounts
Cupmounts
Size 1
Features:
52066
20
8-14
52081
52095
50
15-30
52062
52067
40
14-26
52082
52096
100
30-50
52063
52068
70
26-38
52083
52097
150
50-80
52064
52069
100
38-62
180
52084
52098
250
80-110
52085
52099
400
110-160
700
52064
52085
160
600
52063
140
52084
500
120
LOAD (LB.)
Fail-safe Construction:
Available in four basic sizes, these compact,
low-profile isolators have interlocking
components of steel (other metals available)
and standard neoprene or high damped
silicone elastomers. They can be used to
mount your equipment in compression,
tension and shear applications. No matter
how the mount is oriented or the load is
directed, the elastomer is in compression.
LOAD (LB.)
Size 2
52062
100
80
400
52083
300
52082
60
200
52061
40
52081
100
20
0
0.01
0.02
0.03
0.04
0.05
DEFLECTION (IN.)
34
35
0.06
0.07
0.08
0.01
0.02
0.03
0.04
0.05
DEFLECTION (IN.)
0.06
0.07
Cupmounts
Size 3
Cupmounts
Mounting Configurations
Size 4
Multi-directional loading
Fail-Safe construction
Choice of elastomers
Since the elastomer is always in compression, cupmounts operate with equal eciency in upright,
inverted or bulk-head mounting positions, regardless of
how the mount is oriented or the load directed.
Typical Transmissibility
9
Neoprene
Elastomer
Part No.
Maximum
Vehicular
Stationary Load Load Range
(lbs)
(lbs)
52101
250
65-100
52111
600
80-120
52102
400
100-150
52112
800
120-185
52103
650
155-200
52113
1400
185-285
52104
900
200-285
52114
1800
285-530
TRANSMISSIBILITY (OUTPUT/INPUT)
Neoprene
Maximum
Elastomer Stationary Load
Part No.
(lbs)
Vehicular
Load
Range
(lbs)
Neoprene
HDS
1
0.7
0.4
0.1
10
20
30
40
50
60
70
80
FREQUENCY (Hz)
Elastomer Data
36
37
Environment
Neoprene
Silicone
Temperature
-20O to +180OF
-80O to +300OF
Ozone Resistance
Good
Excellent
Oil Resistance
Excellent
Good
Heat Aging
Good
Excellent
Stable-Flex Mounts
Stable-Flex Mounts
AXIAL STIFFNESS CURVES
200
4.32
M10 x 1.5
-10
150
2.50
1.73
1.50
0.47
LOAD (LB.)
0.35
0.35
-8
100
-6
-4
2.50
50
-2
1.40
0
0
0.1
0.12 0.14
DEFLECTION (IN.)
Features:
Zinc Plated
Part No.
Stainless Steel
Part No.
Color Code
52045-2
52045-2SS
30
Yellow
52045-4
52045-4SS
55
Red
52045-6
52045-6SS
75
Green
52045-8
52045-8SS
120
Blue
52045-10
52045-10SS
180
White
Notes:
Add 'A' to part number for 3/8-16 Thread
Stainless Steel parts have two slotted base holes
38
39
250
-65
-55
200
150
-45
100
50
0
3.94
4.72
LOAD (LB.)
E
2.36
0.56
0.55
0.43
M12
465
2.95
0.51
1.18
0.51
M16
52011-75
770
52012-55
1145
52012-75
1.65
7.17
8.98
4.41
0.71
1.34
0.71
M20
0.2
0.25
-75
2500
990
2.86
0.1
0.15
DEFLECTION (IN.)
660
52012-45
52012-65
0.05
3000
220
52011-55
7.20
145
330
5.51
-45
Max. Load
(lbs)
52011-45
1.10
-55
600
265
1.97
800
200
52010-75
52011-65
-65
1000
400
LOAD (LB.)
52010-65
0.79
-75
1200
110
1.52
0.2
1400
52010-45
52010-55
0.1
0.15
DEFLECTION (IN.)
1600
The mounts oer a low vertical natural frequency of 8 Hz at rated load. Axial stiness
curves are included on the following page.
Horizontal stiness in the long direction is
2.5 times the axial stiness and in the short
direction it is 0.75 times the axial stiness.
A
0.05
Part No.
2000
-65
1500
-55
1000
-45
500
0
1550
2200
40
41
0.05
0.1
0.15
DEFLECTION (IN.)
0.2
0.25
Universal Mounts
Universal Mounts
AXIAL STIFFNESS
450
15
15
200
400
350
14
14
150
LOAD (LBS)
LOAD (LBS)
300
250
13
200
150
12
100
11
100
13
12
50
11
50
0
SNUBBING WASHER
(OPTIONAL)
ISOLATED EQUIPMENT
E
C MOUNTING HOLE
B ELASTOMER
R-RADIUS
REQUIRED
SUPPORT
STRUCTURE
FINSTALLED
FINSTALLED
ISOLATED
FRAME
C MOUNTING HOLE
B ELASTOMER
AXIAL STIFFNESS
400
RADIAL STIFFNESS
G
Thin
Thick
Support Support
Part No.
60011 thru 15
0.39
0.78
0.75
1.25
0.50
1.25
0.37
N/A
0.03
60021 thru 25
0.53
1.31
1.25
1.87
0.78
1.94
0.50
0.56
0.06
60031 thru 35
0.64
1.55
1.50
2.53
0.90
2.45
0.75
0.88
0.08
60041 thru 45
0.94
2.30
2.25
3.50
1.00
2.88
1.00
1.12
0.12
60051 thru 55
1.06
2.55
2.50
4.88
1.25
3.38
1.00
1.25
0.12
60165-1 thru 5
0.64
1.55
1.50
2.53
0.90
1.83
0.25
N/A
0.08
60166-1 thru 5
0.39
0.78
0.75
1.25
0.50
1.06
0.19
N/A
0.03
42
43
AXIAL STIFFNESS
450
35
LOAD (LBS)
R-RADIUS
REQUIRED
LOAD (LBS)
0.1
LOAD (LBS)
0.02
0.04
0.06
0.08
DEFLECTION (INCHES)
LOAD (LBS)
Features:
RADIAL STIFFNESS
Universal Mounts
Universal Mounts
60165-1 thru -5 Series
350
44
43
1400
300
1200
1000
43
800
42
41
600
LOAD (LBS)
LOAD (LBS)
44
250
42
200
41
150
100
400
50
200
0.05
0.1
0.15
DEFLECTION (IN)
0.2
RADIAL STIFFNESS
55
1200
55
8000
1000
7000
800
54
5000
53
4000
3000
52
2000
LOAD (LBS)
LOAD (LBS)
6000
54
53
600
400
52
51
51
200
1000
0
0.05
0.1
0.15
DEFLECTION (IN)
0.2
AXIAL STIFFNESS
1000
RADIAL STIFFNESS
250
-4
-5
-4
-3
800
200
-2
600
-1
400
-3
150
-2
100
200
-1
50
0
0.05
0.1
0.15
DEFLECTION (IN)
0.2
RADIAL STIFFNESS
70
700
-5
-5
60
600
-4
500
400
-3
300
-3
30
-2
-1
-1
0
40
20
-2
100
45
50
-4
200
Mounting Configurations
44
-5
LOAD (LBS)
1600
45
400
LOAD (LBS)
RADIAL STIFFNESS
450
45
1800
LOAD (LBS)
AXIAL STIFFNESS
2000
LOAD (LBS)
0.1
10
0
0.02
60285 Series
-5
-5
6000
-4
5000
-3
LOAD (LB.)
LOAD (LB.)
800
600
-2
-1
400
-4
4000
-3
3000
-2
2000
200
0
0.05
0.1
0.15
DEFLECTION (IN.)
-5
LOAD (LB.)
-3
150
-2
100
-1
50
60278 Series
-4
1500
-3
1000
-2
-1
500
0
Required Support
Thickness: 0.88
Hole Dia: 1.58/1.62
0.05
0.1
0.15
DEFLECTION (IN.)
0.2
-5
400
350
LOAD (LB.)
-4
300
250
-3
200
150
-2
100
-1
50
0
46
47
0.05
0.1
0.15
DEFLECTION (IN.)
0.2
-5
1000
-4
200
Required Support
Thickness: 1.25
Hole Dia: 2.58/2.62
0.2
LOAD (LB.)
Required Support
Thickness: 0.25
Hole Dia: 1.58/1.62
-1
1000
STEEL
WEAR
PLATES
-4
800
600
-3
400
-2
-1
200
0
0.1
Color Code
Yellow
Red
Green
Blue
White
48
49
120
LOAD (LB.)
100
-2
80
60
-1
40
20
0
0.05
0.1
0.15
0.2
0.25
DEFLECTION (IN.)
Features
Part No.
51505-1
51505-2
51505-3
51506-1
51506-2
51506-3
51507-1
51507-2
51507-3
51507-4
51508-1
51508-2
51508-3
51508-4
51508-5
51510-1
51510-2
51510-3
51510-4
51510-5
51512-1
51512-2
51512-3
51512-4
51512-5
51516-1
51516-2
51516-3
51516-4
50
51506 Series
AXIAL LOAD VS. DEFLECTION
250
-3
200
-2
LOAD (LB.)
150
-1
100
50
0.05
0.1
0.15
0.2
DEFLECTION (IN.)
51507 Series
51
0.25
51508 Series
51516 Series
51510 Series
Typical Installation
51512 Series
52
53
Part No.
60230
60231
60232
60233
300
60233
60223
60232
60231
250
60222
LOAD (LB.)
LOAD (LB.)
200
150
60221
100
200
60230
150
100
50
50
60220
Features
DEFLECTION (IN.)
Part No.
60245
60246
60247
60248
60248
1000
60236
60241
500
400
300
LOAD (LB.)
LOAD (LB.)
60247
600
200
60235
60240
100
0
0.02
0.04
0.06
800
60246
600
400
60245
200
0
0.08
E(min.) F(min.)
1.25
1.10
R(min.)
0.06
2000
2.00
1.50
0.06
1.70
0.06
2.25
1.70
0.06
2.85
2.20
0.06
3.50
2.50
0.12
4.25
2.70
0.12
LOAD (LB.)
2.25
2500
60262
60251
60250
60261
1500
1000
60260
500
0.04
0.08
0.12
0.16
DEFLECTION (IN.)
55
0.08
60263
500
54
0.06
2000
1000
0.04
60252
1500
Part No.
60260
60261
60262
60263
LOAD (LB.)
Part No.
60250
60251
60252
60253
0.02
DEFLECTION (IN.)
DEFLECTION (IN.)
Part No.
0.08
700
0.06
1200
60237
60242
60238
60243
800
0.04
DEFLECTION (IN.)
Part No.
Color Code Max. Load (lbs.)
60235/60240
Red
230
60236/60241
Green
360
60237/60242
Blue
520
60238/60243
White
720
900
0.02
0.2
0.04
0.08
0.12
DEFLECTION (IN.)
0.16
61591 Series
Part No.
61597-1
61597-2
61597-3
61597-4
61597-5
61592 Series
Features:
Color Code
Yellow
Red
Green
Blue
White
AXIAL STIFFNESS
200
-5
180
Part No.
Max. Axial
Load (lbs.)
Part No.
Max. Axial
Load (lbs.)
Color Code
Color Code
61591-1
85
Yellow
61592-1
150
Red
61591-2
120
Red
61592-2
185
Green
61591-3
155
Green
61592-3
320
Blue
61592-4
425
White
61591-4
275
Blue
Deflection at Maximum Load = 0.25
Radial Stiness = 2.5 x Axial Stiness
LOAD (POUNDS)
160
-4
140
120
-3
100
80
-2
60
-1
40
20
0
0
0.05
0.1
0.15
DEFLECTION (INCHES)
56
57
0.2
140
-20
LOAD (POUNDS)
120
100
-15
80
-10
60
40
Compressed
Approx. Free
Max. Extended
Height (H)
1.19
1.50
1.88
20
0
0.04
0.08
0.12
0.16
DEFLECTION (INCHES)
50764 Series
50722 Series
Part Number
50722-1
50722-2
50722-3
50722-5
50
350
Height (H)
0.91
1.22
1.56
300
35
-2
30
-1
25
20
15
-50
250
200
-35
150
100
10
5
0
-80
-3
LOAD (POUNDS)
LOAD (POUNDS)
40
Compressed
Approx. Free
Max. Extended
400
-5
45
Compressed
Approx. Free
Max. Extended
0.04
0.08
0.12
0.16
DEFLECTION (INCHES)
58
59
Height (H)
1.25
1.62
1.94
50
0
0.05
0.1
0.15
0.2
DEFLECTION (INCHES)
0.25
All-Attitude Mounts
All-Attitude Mounts
Flush Mount Style
Features
Holder Style
Axial Stiness
Flush Mount Style
Holder Style
Part No.
Color Code
Max.
Stationary
Load (lbs.)
Part No.
Color Code
Max.
Stationary
Load (lbs.)
56421-30
Gray
3.0
56422-40
Red
4.5
56421-40
Red
4.5
56422-50
Yellow
7.0
56421-50
Yellow
7.0
56422-60
Green
10.0
56421-60
Green
10.0
60
61
All-Attitude Mounts
All-Attitude Mounts
Flush Mount Style
Features
Holder Style
Part No.
Color Code
Max.
Stationary
Load (lbs.)
52205
Red
15
52205-H
Red
15
52206
Green
25
52206-H
Green
25
52207
Yellow
35
52207-H
Yellow
52208
Blue
50
52208-H
Blue
600
52207
500
400
300
52206
35
200
52205
50
100
0.05
0.1
0.15
0.2
DEFLECTION (IN.)
63
50
40
30
20
52208
52205 52206
10
6 7 8 9 10
LOAD (POUNDS)
62
Color Code
700
LOAD (LB.)
Part No.
Max.
Stationary
Load (lbs.)
Holder Style
0.25
20
30
52207
40
50
Platemounts
Platemounts
1.68
1.41
1.00
0.38
0.03
0.53
0.84
(2) 0.141
0.166
0.62
Part No.
62433-1
62433-2
62433-3
62433-4
62433-6
Fail-safe operation of electronic and electromechanical equipment, appliances, oce
machines and transportation equipment are
typical applications for Tech Products Plate
Mounts.
Designed for light to medium loads, they
isolate mounted equipment from external
vibration and/or isolate vibration produced
by the mounted equipment itself.
Color Code
Yellow
Red
Green
Blue
White
Deflection at Max. Load = 0.18
Part No.
62434-6P
62434-9P
62434-13P
62434-16P
Square Shape
Diamond Shape
Color Code Max. Load (lbs.) Part No.
Color Code Max. Load (lbs.)
Yellow
6
62434-6
Yellow
6
Red
9
62434-9
Red
9
Green
13
62434-13
Green
13
Blue
16
62434-16
Blue
16
Deflection at Max. Load = 0.18
2.98
2.475
2.25 SQUARE
0.34
1.062
1.75 TYP.
0.391
0.062
0.56
2.25
2.00
(2X) 0.19
0.391
(4X) 0.19
Part No.
62212
62220
62230
62245
62260
64
65
Square Shape
Diamond Shape
Color Code Max. Load (lbs.)
Part No.
Color Code Max. Load (lbs.)
Yellow
12
62232
Yellow
12
Red
20
62239
Red
20
Green
30
62250
Green
30
Blue
45
62265
Blue
45
Blue-White
60
62280
Blue-White
60
Deflection at Max. Load = 0.185
Platemounts
1.66
1.41
1.25
1.00
.032
(4X) 0.16
0.39
0.05
1.50
0.166
Square Shape
Diamond Shape
Color Code Max. Load (lbs.) Part No.
Color Code Max. Load (lbs.)
Yellow
0.5
62491-A
Yellow
0.5
Red
1
62491-1
Red
1
Green
2
62491-2
Green
2
Blue
4
62491-4
Blue
4
White
6
62491-6
White
6
Deflection at Max. Load = 0.06
0.17
0.17
1.00
0.46
Part No.
62103
62106
62109
62112
62114
62117
62120
62126
0.26
Square Shape
Diamond Shape
Color Code Max. Load (lbs.) Part No.
Color Code Max. Load (lbs.)
Yellow
3
62123
Yellow
3
Red
6
62166
Red
6
Red-Green
9
62129
Red-Green
9
Green
12
62132
Green
12
Green-Blue
14
62134
Green-Blue
14
Blue
17
62137
Blue
17
Blue-White
20
62140
Blue-White
20
Blue-Yellow
26
62146
Blue-Yellow
26
Deflection at Max. Load = 0.09
1.68
1.414
2.98
2.475
2.25
1.75
0.75
(2X) 0.16
0.26
(2) 0.16
0.17
0.20
0.63
1.24
(4X) 0.16
2.00
0.25
1.25
0.035
0.59
1.015
(2X) 0.16
0.062
0.39
(4X) 0.19
(4X) 0.16
Part No.
62004
62008
62012
62020
2.34
1.95
1.00
0.166
1.25
1.00
1.78
1.38
0.15
0.41 0.32
Part No.
62490-A
62490-1
62490-2
62490-4
62490-6
Platemounts
Square Shape
Diamond Shape
Color Code Max. Load (lbs.) Part No.
Color Code Max. Load (lbs.)
Yellow
4
62024
Yellow
4
Red
8
62028
Red
8
Green
12
62032
Green
12
Blue
20
62040
Blue
20
Deflection at Max. Load = 0.06
66
Part No.
62330
62340
62350
62370
62390
67
2.25
0.390
2.00
(2X) 0.19
Square Shape
Diamond Shape
Color Code Max. Load (lbs.) Part No.
Color Code Max. Load (lbs.)
Red
30
62332
Red
30
Red-Green
40
62342
Red-Green
40
Green
50
62352
Green
50
Green-Blue
70
62372
Green-Blue
70
Blue
90
62392
Blue
90
Deflection at Max. Load = 0.13
Available with 3/8-16 threaded core
51809
51810
51808
LOAD (LB.)
40
51807
30
51806
20
51805
10
0
0.01
0.02
0.03
0.04
0.05
DEFLECTION (IN.)
Features
51838
51839
51840
60
Ring Part No. Bushing Part No. Color Code Max. Load (lbs.)
51805
51820
Silver
5
51806
51821
Yellow
10
51807
51822
Red
15
51808
51823
Green
20
51809
51824
Blue
25
51810
51825
White
30
70
51837
50
LOAD (LB.)
0.06
51836
40
30
51835
20
10
0.01
0.02
0.03
0.04
0.05
0.06
DEFLECTION (IN.)
51879
0.07
0.08
Ring Part No. Bushing Part No. Color Code Max. Load (lbs.)
51835
51850
Silver
20
51836
51851
Yellow
25
51837
51852
Red
35
51838
51853
Green
45
51839
51854
Blue
55
51840
51855
White
65
51877
140
51875
51873
LOAD (LB.)
120
51871
100
80
51869
60
40
20
0
0.02
0.04
0.06
0.08
0.1
0.12
0.14
DEFLECTION (IN.)
Ring Part No. Bushing Part No. Color Code Max. Load (lbs.)
51869
51870
Silver
30
51871
51872
Yellow
40
51873
51874
Red
50
51875
51876
Green
65
51877
51878
Blue
85
51879
51880
White
100
68
69
Bubble Mounts
1.414 .010
Max. Load
(lbs.)
50640
Yellow
4.0
50641
Red
6.5
50642
Green
11.0
50643
Blue
15.0
50644
White
18.0
50680-1
Yellow
4.0
50680-2
Red
6.5
50680-3
Green
11.0
50680-4
Blue
15.0
50680-5
White
18.0
35
(2X) 0.16
AXIAL STIFFNESS
40
0.170
-3A
35
30
-2A
25
20
-1A
15
10
0.256
5
0
0.05
0.1
0.15
0.2
0.25
DEFLECTION (IN.)
RADIAL STIFFNESS
Axial Stiness
35
1.25
-3A
-2A
30
30
50643
50644
0.25
20
50680-5
50680-4
50642
15
LOAD (LBS.)
REF.
LOAD (LB.)
25
A
1.68
0.90
50680-3
10
0.75
0.03
0.65
-1A
25
50640
Color
Code
The High Deflection Silicone mounts are low profile isolators that have large deflection
capability for shock and vibration attenuation. The mounts are designed to support loads
ranging from 5 to 15 lbs. Retaining straps are available for fail-safe installation. Typical
applications include ruggedized electronics and computer equipment.
50641
50680-2
50680-1
0.75
0
Part No.
LOAD (LB.)
0.05
0.1
0.15
0.2
0.25
0.3
0.35
DEFLECTION (IN.)
70
71
Part Number
61829-1A
5-7
61829-2A
7-10
61829-3A
10-15
20
15
10
5
0
0.1
0.2
0.3
0.4
DEFLECTION (IN.)
0.5
Snubbing Washers
Material: Steel
Finish: Zinc Plating
Product
51505-( )
51506-( )
51507-( )
51508-( )
51510-( )
51512-( )
51516-( )
51641-( )
51700-( )
51716-( )
60011 to 15
60021 to 25
60031 to 35
60041 to 45
60055 to 55
60165-( )
60166-( )
60220 to 23
60230 to 33
60235 to 38
60240 to 43
60245 to 48
60250 to 53
60260 to 63
60270-( )
60272-( )
60278-( )
60285-( )
61591-( )
61592-( )
61597-( )
Part
No.
52001
52002
52003
52004
52005
52006
52007
52008
Load (lbs.)
Min. Max.
20
100
300
500
1200
1200
2400
4800
100
300
550
1200
2400
4800
9600
19200
3.00 2.38
4.19 3.50
5.13 4.25
6.88 6.00
10.00 8.50
13.50 12.00
18.50 16.00
24.00 20.00
0.31
0.34
0.44
0.44
0.75
0.75
1.25
2.00
3/8-16
1/2-13
1/2-13
1/2-13
5/8-11
5/8-11
1-14
1-14
0.47
0.54
0.54
0.54
0.75
0.75
0.88
0.88
H*
1.94
1.94
2.94
2.94
2.94
2.94
2.94
2.94
0.12
0.12
0.12
0.12
0.19
0.19
0.25
0.25
* H = Free Height; H+1/4 = nominal loaded height for steady force applications
72
73
Washer P/N
00181
00181-1
00181-1
00308-1
00308-2
00308-3
00185
00182
00181-1
00182
00181
00182
00183
00184
00185
00183
00181
00181
00182
00182
00183
00183
00183
00184
00182
00183
00183
00185
00183
00183
00181
A
1.56
2.00
2.00
2.00
2.25
2.50
5.06
2.13
2.00
2.13
1.56
2.13
2.81
3.88
5.06
2.81
1.56
1.56
2.13
2.13
2.81
2.81
2.81
3.88
2.13
2.81
2.81
5.06
2.81
2.81
1.56
B
0.391
0.450
0.450
0.510
0.635
0.760
1.10
0.532
0.450
0.532
0.391
0.532
0.657
0.938
1.10
0.657
0.391
0.391
0.532
0.532
0.657
0.657
0.657
0.938
0.532
0.657
0.657
1.10
0.657
0.657
0.391
T
.090
.125
.125
.130
.150
.190
.250
.134
.125
.134
.090
.134
.188
.250
.250
.188
.090
.090
.134
.134
.188
.188
.188
.250
.134
.188
.188
.250
.188
.188
.090
Stud/Plate Mounts
Style PS
Style SS
Features:
lbs-inch
6-32
10
8-32
15
10-32
25
1/4-20
53
5/16-18
105
3/8-16
192
Style PP
Part No.
D
M
P (Depth) Max. Shear (lbs.)
50908
3/8
1/2
6-32 (1/8)
3.5
50903*
9/16
1/2
6-32 (1/8)
4.5
50905*
9/16
1/2
6-32 (1/8)
6
50907*
9/16
1/2
6-32 (1/8)
9
Standard elastomer is Natural Rubber, (*) indicates Neoprene
Style PS
Part No.
D
M
6-32 x S
P (Depth)
Max. Shear (lbs.)
50168* 3/8
3/8
1/4
6-32 (5/32)#
3.4
50169* 3/8
5/16
1/4
6-32 (5/32)
3
50172* 3/8
5/16
3/16
6-32 (5/32)
3
50177* 3/8
5/16
3/8
6-32 (5/32)
4
50181 7/16 13/32
1/4
6-32 (1/8)
2.5
50184* 7/16 13/32
1/4
6-32 (1/8)
3.4
50194* 7/16 13/32
1/4
6-32 (1/8)
6.5
50171* 7/16
1/2
3/8
6-32 (5/32)#
3.5
50170* 7/16
1/2
3/8
6-32 (5/32)#
4.4
50176* 7/16
1/2
1/4
6-32 (5/32)#
4.4
50986* 7/16
1/2
1/4
6-32 (1/8)#
3.5
65021* 7/16
5/8
1/4
6-32 (1/8)
3
50838* 7/16
3/4
1/4
6-32 (1/8)
2.5
Standard elastomer is Natural Rubber, (*) indicates Neoprene
(#) indicates blind insert
Style SS
Part No.
50178
50179
50196
1/2-13
600
Note: Do not twist elastomer during installation
74
75
D
7/16
7/16
7/16
M
13/32
13/32
13/32
6-32 x S
1/4
1/4
3/8 - 1/4
D
E
Max. Shear
Part No. (Square) (Dia.)
M
N
8-32 x S
(lbs.)
51021
1/2
3/8
9/16
3/8
9/16
2.8
51022
1/2
3/8
9/16
3/8
9/16
3.3
51023*
1/2
3/8
9/16
3/8
9/16
5.3
51024*
1/2
3/8
9/16
3/8
9/16
7.5
Standard elastomer is Natural Rubber, (*) indicates Neoprene
Style PP
Style PS
Style P
Part No.
D
M
P
51110
7/16
1/2
8-32
51112
7/16
1/2
8-32
51060
9/16
1/2
8-32
51062
9/16
1/2
8-32
P thread depth is minimum one thread diameter
Style PP
Part No.
D
M
P
51100
7/16
1/2
8-32
51102
7/16
1/2
8-32
51050
9/16
1/2
8-32
51051
9/16
1/2
8-32
51052
9/16
1/2
8-32
51053
9/16
1/2
8-32
65024*
9/16
1/2
8-32
P thread depth is minimum one thread diameter
Style PS
Part No.
D
M
8-32 x S
P
Max. Shear (lbs.)
51090 7/16
1/2
3/8
8-32
3.3
51092 7/16
1/2
3/8
8-32
4.8
51040 9/16
1/2
1/4
8-32
4.5
51041 9/16
1/2
1/4
8-32
5.4
51042 9/16
1/2
3/8
8-32
6
51044 9/16
1/2
3/8
8-32
4.5
51056* 9/16
1/2
3/8
8-32
6
51058 9/16
1/2
3/8
8-32#
4.5
51067 9/16
1/2
3/8
8-32
4.5
Standard elastomer is Natural Rubber, (*) indicates Neoprene
P thread depth is minimum one thread diameter
(#) indicates blind insert
Max. Comp.
(lbs.)
6.8
8.5
12
14.5
76
77
Style SS
Style S
Style SS
Style PS
Style S
Part No.
51120
51122
51070
51072
D
7/16
7/16
9/16
9/16
M
1/2
1/2
1/2
1/2
8-32 x S
3/8
3/8
3/8
3/8
Style SS
Part No.
50912
50913
50914
50915
50916*
50917*
50918*
50919*
50920*
51081
51082
51083*
51084*
51031
51032
51033*
51034*
51036
51055*
D
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
7/16
7/16
7/16
7/16
9/16
9/16
9/16
9/16
9/16
9/16
M
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
8-32 x S
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
1/2
1/2
Style PS
Part No.
D
M
S
P
51045 9/16
1/2
8-32 x 3/8
10-32
51047 9/16
1/2
10-32 x 3/8
10-32
51059* 9/16
1/2
10-32 x 3/8
10-32
51066 9/16
1/2
10-32 x 3/8
8-32
51068 9/16
1/2
10-32 x 3/8
8-32
51136
1
3/4
10-32 x 3/8
10-32
P thread depth is minimum one thread diameter
Style SS
Part No.
51037*
51048
51057
51135
M
1/2
1/2
1/2
3/4
10-32 x S
3/8
3/8 - 3/16
3/8
3/8
78
D
9/16
9/16
9/16
1
79
D
3/4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
M
1/2
17/32
17/32
17/32
41/64
3/4
3/4
3/4
27/32
1
1
1
1
3/4
1
Style SS
Style S
Style P
Part No.
D
M
P
51205*
3/4
1/2
1/4-20
50938*
1
17/32
1/4-20
51181
1
3/4
1/4-20
P thread depth is minimum one thread diameter
Style S
Part No.
51494*
51138
51139
51140
51581
51185
51187
51191*
50783*
51195*
51196
51197
50889*
50828*
51176*
1/4-20 x S
3/4
3/8
3/8
3/8
1/2
1/2
1/2
7/8
3/4
1/2
3/8
1/4
3/4
5/8
1/4
80
Style SS
Part No.
D
M
1/4-20 x S Max. Shear (lbs.)
50820*
3/4
1/2
1/2
12
50859*
1
3/8
1/2
30
51123*
1
17/32
1/2
30
51127
1
17/32
3/8
30
51128
1
17/32
3/8
34
51130
1
17/32
1/2 - 1/4
32
51131
1
17/32
1/2
15
51132
1
17/32
1/2
30
51133
1
17/32
1/2
34
50965*
1
1/2
1/2
35
51154*
1
3/4
3/8
21
51186*
1
3/4
3/8
25
51141
1
3/4
1/2
15
51142
1
3/4
1/2
18
51143
1
3/4
1/2
21
51144*
1
3/4
1/2
18
51146*
1
3/4
1/2
21
50855*
1
3/4
1/2
25
51173*
1
3/4
1/2
15
51147
1
3/4
5/8
18
51148*
1
3/4
5/8
25
51150*
1
3/4
3/4
15
51152
1
3/4
3/4
21
51153*
1
3/4
3/4
21
51158
1
3/4
3/4
18
51160*
1
3/4
3/4
25
51155*
1
3/4
1/4 - 5/8
25
51289
1
3/4
3/8 - 1/2
30
51157*
1
3/4
1/2 - 3/4
25
50888*
1
3/4
1/2 - 3/4
21
51184*
1
3/4
1/2 - 3/4
15
51159
1
3/4
1/2 - 1
30
51164*
1
1
1/2
12
5/8
10
51290*
1
1
50773
5/8
30
1
1
Standard elastomer is Natural Rubber, (*) indicates Neoprene
Standard inserts are zinc plated
81
D
5/8
3/4
3/4
3/4
3/4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
M
1/4-20 x S
5/8
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
17/32
1/2
3/4
1/2
3/4
3/8
3/4
3/8
3/4
1/2
3/4
1/2
3/4
1/2
3/4
1/2
3/4
1/2
3/4
3/4
1
1/2
1
1/2
1
3/4
Style PS
Style PS
Style PP
Part No.
D
M
P
50924
1
3/4
1/4-20
51172
1
3/4
1/4-20
P thread depth is minimum one thread diameter
Style PS
Part No.
50823*
51201*
51202*
51203*
51204*
50839*
51129*
51145*
51151*
51156*
51161
51162
51163
51166*
51188*
51582
51137
51198*
50782*
P
1/4-20
1/4-20
1/4-20
1/4-20
1/4-20
1/4-20
1/4-20
1/4-20
1/4-20
1/4-20
1/4-20
1/4-20
1/4-20
1/4-20
1/4-20
1/4-20
1/4-20
1/4-20
1/4-20
82
Style PS
Part No.
D
M
5/16-18 x S
P
Max. Shear (lbs.)
51283*
1
1/2
9/16
5/16-18
16
51284*
1
1/2
9/16
5/16-18
22
51285*
1
1/2
9/16
5/16-18
35
51286*
1
1/2
9/16
5/16-18
40
50835*^
1
3/4
3/8
5/16-18
40
51234
1
3/4
1/2
5/16-18
16
51258
1
3/4
9/16
5/16-18
40
51276*
1
3/4
5/16
5/16-18
16
51277*
1
3/4
5/16
5/16-18
19
51278*
1
3/4
5/16
5/16-18
25
51279*
1
3/4
5/16
5/16-18
31
51313*
1
3/4
5/16-18
25
1
51314*
1
3/4
5/16-18
38
1
51327*
9/16
5/16-18
21
1
1
51328*
9/16
5/16-18
31
1
1
51329*
9/16
5/16-18
45
1
1
51330*
9/16
5/16-18
63
1
1
50780*
3/4
5/16-18
63
1
1
50817*
3/4
5/16-18
85
1
1
51352
1
9/16
5/16-18
66
1
65007*^ 1
1
9/16
5/16-18
66
50928*
5/8
5/16-18
55
1
1
50975*
5/8
5/16-18
65
1
1
51376
1
9/16
5/16-18
30
1
51377
1
9/16
5/16-18
40
1
51378
1
9/16
5/16-18
50
1
51379
1
9/16
5/16-18
65
1
51400*
1
5/8
5/16-18
45
1
51542*
1
9/16
5/16-18
40
1
Standard elastomer is Natural Rubber, (*) indicates Neoprene
P thread depth is minimum one thread diameter
Standard inserts are zinc plated, (^) indicates phosphate finish
83
Style SS
Style SS
Style SS
Part No.
D
M
5/16-18 x S Max. Shear (lbs.)
50852*^
1
1/2
5/8
45
51239
1
3/4
3/8
22
51240*
1
3/4
3/8
22
51241
1
3/4
9/16
15
51242
1
3/4
9/16
18
51243
1
3/4
9/16
22
51247
1
3/4
5/8
15
51251
1
3/4
3/4
15
51252
1
3/4
3/4
18
51253
1
3/4
3/4
22
51257*
1
3/4
9/16
22
51260*
1
3/4
1/2 - 7/8
22
51280*
1
3/4
1/2 - 7/8
18
51282*
1
3/4
1/2 - 7/8
25
51262*
1
1
9/16
12
51263
1
1
9/16
16
51265
1
1
3/4
35
51266
1
1
3/4
8
51267
1
1
3/4
12
51270
1
1
1/2 - 3/4
12
50825
1
1
1/2
30
51296
1
5/8
20
1
51296-1
1
5/8
28
1
50798*
3/4
9/16
25
1
51301
3/4
9/16
36
1
51302
3/4
9/16
43
1
51303
3/4
9/16
52
1
51304
3/4
9/16
45
1
51305*
3/4
1/2 - 3/4
45
1
51306
3/4
3/4
36
1
51307
3/4
3/4
43
1
51308
3/4
3/4
52
1
51310
3/4
5/8
43
1
51311
1
9/16
31
1
51312
1
9/16
38
1
Standard elastomer is Natural Rubber, (*) indicates Neoprene
Standard inserts are zinc plated, (^) indicates phosphate finish
84
Style SS
Part No.
D
M
5/16-18 x S Max. Shear (lbs.)
51315
1
3/4
31
1
51316
1
3/4
38
1
51297*
5/8
27
1
1
51298*
5/8
34
1
1
51299*
5/8
60
1
1
51320
9/16
21
1
1
51321
9/16
27
1
1
51322
9/16
34
1
1
51325
3/4
27
1
1
51326
3/4
34
1
1
51337*
9/16
60
1
1
51344*
7/8
27
1
1
51345
7/8
34
1
1
51349
3/4
60
1
1
51480*
5/8
5/8
35
1
51481*
5/8
5/8
45
1
51482*
5/8
5/8
55
1
51483*
5/8
5/8
65
1
51484*
5/8
5/8
75
1
50136*
1
1 1/4
87
1
51340
1
9/16
27
1
51341
1
9/16
41
1
51342
1
9/16
66
1
51343
1
9/16
76
1
51348
1
7/8 - 1
66
1
51353*
1
3/4
27
1
51354*
1
3/4
41
1
51355*
1
3/4
66
1
51356*
1
3/4
76
1
51357*
1
3/4
87
1
51358
1
3/4
76
1
65028*^
1
3/4
76
1
51401*
1
5/8
45
1
51460*
2
5/8
50
1
51462*
2
5/8
100
1
Standard elastomer is Natural Rubber, (*) indicates Neoprene
Standard inserts are zinc plated, (^) indicates phosphate finish
85
Style P
Style S
Style SS
Style PS
Style PP
Part No.
D
M
P
51272*
1
1
5/16-18
51275*
1
1
5/16-18
51318
5/16-18
1
1
51323
5/16-18
1
1
51324
5/16-18
1
1
50137*
1
5/16-18
1
P thread depth is minimum one thread diameter
Style P
Part No.
D
M
P
51254
1
3/4
5/16-18
51335
3/4
5/16-18
1
P thread depth is minimum one thread diameter
Style PS
Part No.
D
M
3/8-16 x S
P
51588*
7/8
5/8
3/8-16
1
51380
1
5/8
3/8-16
1
51381
1
5/8
3/8-16
1
51382
1
5/8
3/8-16
1
51383
1
5/8
3/8-16
1
51384
1
5/8
3/8-16
1
50868-1* 2
1
7/8
3/8-16
50868-2* 2
1
7/8
3/8-16
50868-3* 2
1
7/8
3/8-16
50868-4* 2
1
7/8
3/8-16
50868-5* 2
1
7/8
3/8-16
P thread depth is minimum one thread diameter
Style SS
Part No.
51390
51391
51392
51393
51394
51395
51396
51397
51398*
51399*
51620-1
51620-2
51620-3
51620-4
51620-5
Style S
Part No.
50983^
51255
51244
50840^
50818
51331
51332
51334*
51336*
51319*
51466
51467
51468
51469
51470
D
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
M
3/8
17/32
3/4
3/4
1
3/4
3/4
3/4
3/4
1
1
1
1
1
1
5/16-18 x S
1 1/4
9/16
5/8
1 1/4
5/8
3/4
3/4
9/16
1/2
9/16
3/4
3/4
3/4
3/4
3/4
D
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
M
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
3/8-16 x S
5/8
5/8
5/8
5/8
5/8
3/4
3/4
3/4
3/4
3/4
7/8
7/8
7/8
7/8
7/8
86
87
Style PP
Part No.
51415*
51416*
51417*
51418*
51419*
51553-1*
51553-2*
51553-3*
51553-4*
51553-5*
51555-1*
51555-2*
51555-3*
51555-4*
51555-5*
Style PS
Part No.
51386*
51388*
51420*
51421*
51422*
51423*
51424*
51551-1*
51551-2*
51551-3*
51551-4*
51551-5*
51557-1*
51557-2*
51557-3*
51557-4*
51557-5*
D
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
D
1
1
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
Style PS
M
1 /
1 /
1 /
1 /
1 /
1
1
1
1
1
3
3
3
3
3
M
1
1
1 /
1 /
1 /
1 /
1 /
1
1
1
1
1
3
3
3
3
3
P (Depth)
1/2-13 (1/2)#
1/2-13 (1/2)#
1/2-13 (1/2)#
1/2-13 (1/2)#
1/2-13 (1/2)#
1/2-13 (1/2)
1/2-13 (1/2)
1/2-13 (1/2)
1/2-13 (1/2)
1/2-13 (1/2)
1/2-13 (1/2)
1/2-13 (1/2)
1/2-13 (1/2)
1/2-13 (1/2)
1/2-13 (1/2)
1/2-13 x S
3/4
3/4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
P
1/2-13 (3/8)
1/2-13 (3/8)
1/2-13 (1/2)#
1/2-13 (1/2)#
1/2-13 (1/2)#
1/2-13 (1/2)#
1/2-13 (1/2)#
1/2-13 (1/2)
1/2-13 (1/2)
1/2-13 (1/2)
1/2-13 (1/2)
1/2-13 (1/2)
1/2-13 (1/2)
1/2-13 (1/2)
1/2-13 (1/2)
1/2-13 (1/2)
1/2-13 (1/2)
Max. Shear
38
72
70
90
140
185
225
80
110
145
215
285
38
65
105
140
185
Max. Comp.
80
130
160
200
260
340
410
360
540
760
980
1815
250
410
690
910
1190
Style SS
Part No.
51385
51387*
51410*
51411*
51412*
51413*
51414*
51552-1*
51552-2*
51552-3*
51552-4*
51552-5*
51556-1*
51556-2*
51556-3*
51556-4*
51556-5*
D
1
1
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
M
1
1
1 /
1 /
1 /
1 /
1 /
1
1
1
1
1
3
3
3
3
3
1/2-13 x S
3/4
3/4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Style S
Part No.
50121*
50122*
D
1
1
M
3/4
3/4
1/2-13 x S
3/4
3/4
Standard elastomer is Natural Rubber, (*) indicates Neoprene, (#) indicates blind insert
88
Style S
89
Style PS
Style PS
Part No.
50197*
50198*
51095
51095-1
51453*
65026-2*
51447*
50805*
50926*
50842*
50942*
50952*
65011*
51259
50947-1*
50947-2*
50947-3*
50898*^
51425-1*
51425-2*
51425-3*
51425-4*
51425-5*
51550-1*
51550-2*
51550-3*
51550-4*
51550-5*
51554-1*
51554-2*
51554-3*
51554-4*
51554-5*
D
9.5
9.5
11
11
19
25
25
25
25
25
25
25
25
25
32
32
32
38
51
51
51
51
51
79
79
79
79
79
79
79
79
79
79
M
8
9.5
13
13
16
13
19
19
25
25
25
25
19
19
32
32
32
25
43
43
43
43
43
38
38
38
38
38
76
76
76
76
76
S
M3x0.5 x 4
M3x0.5 x 4
M4x0.7 x 6
M4x0.7 x 4
M4x0.7 x 10
M6x1.0 x 13
M6x1.0 x 13
M6x1.0 x 13
M6x1.0 x 11.5
M6x1.0 x 19
M6x1.0 x 19
M6x1.0 x 11.5
M8x1.25 x 16
M8x1.25 x 14
M8x1.25 x 14
M8x1.25 x 14
M8x1.25 x 14
M8x1.25 x 14
M12x1.75 x 28
M12x1.75 x 28
M12x1.75 x 28
M12x1.75 x 28
M12x1.75 x 28
M12x1.75 x 41
M12x1.75 x 41
M12x1.75 x 41
M12x1.75 x 41
M12x1.75 x 41
M12x1.75 x 41
M12x1.75 x 41
M12x1.75 x 41
M12x1.75 x 41
M12x1.75 x 41
P
6-32
6-32
M4x0.7
M4x0.7
M4x0.7
M6x1.0
M6x1.0
M6x1.0
M6x1.0
M6x1.0
M6x1.0
M6x1.0
M8x1.25
M8x1.25
M8x1.25
M8x1.25
M8x1.25
M8x1.25
M12x1.75
M12x1.75
M12x1.75
M12x1.75
M12x1.75
M12x1.75
M12x1.75
M12x1.75
M12x1.75
M12x1.75
M12x1.75
M12x1.75
M12x1.75
M12x1.75
M12x1.75
Style SS
Part No.
50957*
51098
51487**
50956*
50959-1*
50959-2*
50959-3*
50959-4*
50959-5*
50849*
50845-40*
50819*
51445*
51281*
65005*
50787*
50988*
50785*
50900*
51549-1*
51549-2*
51549-3*
51549-4*
51549-5*
51561-1*
51561-2*
51561-3*
51561-4*
51561-5*
11
11
19
25
25
25
25
25
25
25
25
25
25
25
25
25
32
35
64
79
79
79
79
79
79
79
79
79
79
10
13
13
13
19
19
19
19
19
19
19
19
19
19
19
19
32
25
25
38
38
38
38
38
76
76
76
76
76
M3x0.5 x 6
M4x0.7 x 6
M6x1.0 x 14
M6x1.0 x 19
M6x1.0 x 12
M6x1.0 x 12
M6x1.0 x 12
M6x1.0 x 12
M6x1.0 x 12
M6x1.0 x 13
M6x1.0 x 22
M8x1.25 x 13
M8x1.25 x 14
M8x1.25 x 20
M8x1.25 x 16
M8x1.25 x 20
M8x1.25 x 25
M8x1.25 x 20
M10x1.5 x 23
M12x1.75 x 41
M12x1.75 x 41
M12x1.75 x 41
M12x1.75 x 41
M12x1.75 x 41
M12x1.75 x 41
M12x1.75 x 41
M12x1.75 x 41
M12x1.75 x 41
M12x1.75 x 41
M3x0.5 x 6
M4x0.7 x 6
M6x1.0 x 14
M6x1.0 x 19
M6x1.0 x 12
M6x1.0 x 12
M6x1.0 x 12
M6x1.0 x 12
M6x1.0 x 12
M6x1.0 x 13
M6x1.0 x 14
M8x1.25 x 13
M8x1.25 x 14
M8x1.25 x 20
M8x1.25 x 10
M8x1.25 x 10
M8x1.25 x 25
M8x1.25 x 20
M10x1.5 x 23
M12x1.75 x 41
M12x1.75 x 41
M12x1.75 x 41
M12x1.75 x 41
M12x1.75 x 41
M12x1.75 x 41
M12x1.75 x 41
M12x1.75 x 41
M12x1.75 x 41
M12x1.75 x 41
Standard elastomer is Natural Rubber, (*) indicates Neoprene, (**) indicates Nitrile
90
91
Style P
Part No.
51075
50955*
D
19
19
Style S
Part No.
50833*
50841*
50941*
50834
D
25
25
25
38
M
13
13
M
9.5
21.5
21.5
25
Style S
P
M5 x 0.8
M6 x 1.0
S
M6x1.0 x 13
M6x1.0 x 19
M6x1.0 x 19
M8x1.25 x 14
92
Part No.
Max. Shear
(lbs.)
45
55
85
130
30
45
60
100
20
27
37
65
Shear Stiness
(lbs./in.)
210
280
420
650
150
220
290
485
100
135
180
315
Max. Comp.
(lbs.)
95
130
190
290
90
115
165
265
85
110
170
260
51496-1N
1
51496-2N
1
51496-3N
1
51496-4N
1
51497-1N
2
51497-2N
2
51497-3N
2
51497-4N
2
51498-1N
2
51498-2N
2
51498-3N
2
51498-4N
2
Elastomer = Neoprene
Inserts = Low Carbon Steel (Optional Stainless Steel Available)
93
Comp. Stiness
(lbs./in.)
1200
1625
2375
3625
735
960
1375
2200
520
675
1050
1625
Style PS
Style SS
Style PS
Part No.
50861-1
50861-2
50861-3
50861-4
50861-5
50862-1
50862-2
50862-3
50862-4
50862-5
50863-1
50863-2
50863-3
50863-4
50863-5
50860-1
50860-2
50860-3
50860-4
50860-5
65012-1
65012-2
65012-3
65012-4
65012-5
65013-1
65013-2
65013-3
65013-4
65013-5
D
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
M
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
1
1
1
1
1
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
1
1
1
1
1
S
1/4-20 x 1/2
1/4-20 x 1/2
1/4-20 x 1/2
1/4-20 x 1/2
1/4-20 x 1/2
5/16-18 x 5/8
5/16-18 x 5/8
5/16-18 x 5/8
5/16-18 x 5/8
5/16-18 x 5/8
5/16-18 x 5/8
5/16-18 x 5/8
5/16-18 x 5/8
5/16-18 x 5/8
5/16-18 x 5/8
M6x1.0 x 12mm
M6x1.0 x 12mm
M6x1.0 x 12mm
M6x1.0 x 12mm
M6x1.0 x 12mm
M8x1.25 x 16mm
M8x1.25 x 16mm
M8x1.25 x 16mm
M8x1.25 x 16mm
M8x1.25 x 16mm
M8x1.25 x 16mm
M8x1.25 x 16mm
M8x1.25 x 16mm
M8x1.25 x 16mm
M8x1.25 x 16mm
P
1/4-20
1/4-20
1/4-20
1/4-20
1/4-20
5/16-18
5/16-18
5/16-18
5/16-18
5/16-18
5/16-18
5/16-18
5/16-18
5/16-18
5/16-18
M6x1.0
M6x1.0
M6x1.0
M6x1.0
M6x1.0
M8x1.25
M8x1.25
M8x1.25
M8x1.25
M8x1.25
M8x1.25
M8x1.25
M8x1.25
M8x1.25
M8x1.25
Max. Shear
(lbs.)
8
12
16
22
30
12
22
30
40
55
15
20
30
45
55
8
12
16
22
30
12
22
30
40
55
15
20
30
45
55
Max. Comp.
(lbs.)
25
35
50
65
90
50
75
100
150
180
60
90
125
175
225
25
35
50
65
90
50
75
100
150
180
60
90
125
175
225
Style SS
Part No.
50869-1
50869-2
50869-3
50869-4
50869-5
50870-1
50870-2
50870-3
50870-4
50870-5
50871-1
50871-2
50871-3
50871-4
50871-5
50872-1
50872-2
50872-3
50872-4
50872-5
50873-1
50873-2
50873-3
50873-4
50873-5
65016-1
65016-2
65016-3
65016-4
65016-5
65017-1
65017-2
65017-3
65017-4
65017-5
D
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
M
1/2
1/2
1/2
1/2
1/2
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
1
1
1
1
1
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
1
1
1
1
1
S
1/4-20 x 1/2
1/4-20 x 1/2
1/4-20 x 1/2
1/4-20 x 1/2
1/4-20 x 1/2
1/4-20 x 1/2
1/4-20 x 1/2
1/4-20 x 1/2
1/4-20 x 1/2
1/4-20 x 1/2
5/16-18 x 5/8
5/16-18 x 5/8
5/16-18 x 5/8
5/16-18 x 5/8
5/16-18 x 5/8
5/16-18 x 5/8
5/16-18 x 5/8
5/16-18 x 5/8
5/16-18 x 5/8
5/16-18 x 5/8
M6x1.0 x 12mm
M6x1.0 x 12mm
M6x1.0 x 12mm
M6x1.0 x 12mm
M6x1.0 x 12mm
M8x1.25 x 16mm
M8x1.25 x 16mm
M8x1.25 x 16mm
M8x1.25 x 16mm
M8x1.25 x 16mm
M8x1.25 x 16mm
M8x1.25 x 16mm
M8x1.25 x 16mm
M8x1.25 x 16mm
M8x1.25 x 16mm
94
95
Style P
Part No.
50790-1
50790-5
50792-1
50792-5
D
1
1
1
1
Style S
Part No.
50789-1
50789-5
50791-1
50791-5
D
1
1
1
1
M
3/4
3/4
1
1
M
3/4
3/4
1
1
Style S
P
1/4-20
1/4-20
5/16-18
5/16-18
S
1/4-20 x 1/2
1/4-20 x 1/2
5/16-18 x 5/8
5/16-18 x 5/8
1/2-13
Part No.
D1
D2
M
S
Max. Shear (lbs.)
50144*
140
1
50145*
165
1
50146*
190
1
2
1 /
2
50151
1
140
50152
1
165
50153
1
190
Standard elastomer is Natural Rubber, (*) indicates Neoprene
1/2-20
Part No.
50148
50149
50150
96
97
D1
D2
1 /
S
29/32
29/32
29/32
Conical Bumpers
Fabreeka Pad
Part No.
D1
D2
5/16-18 x S
Max. Shear
(lbs.)
44
49
56
62
45
62
56
44
44
44
Available Thickness
Max. Comp.
(lbs.)
90
100
125
150
95
150
125
90
90
90
1/16
3/32
51360*
9/16
51361
9/16
51362
9/16
51363*
9/16
51364*
3/4
1
1
1
51365*
3/4
51366*
1
51367*
1
50799-N
M8x1.25 x 16mm
M8x1.25 x 16mm
50799-S+
Standard elastomer is Natural Rubber, (*) indicates Neoprene, (+) indicates Silicone
1/8
5/32
3/16
15/64
9/32
11/32
1/2
5/8
3/4
1
98
99
Fabcel Pad
Anti-Vibration Pad
Features:
Fabcel vibration isolation pad is manufactured using the same nitrile compound
developed in 1962. The properties of the
Fabcel pad are designed to provide low
frequency vibration isolation and reduction
of impact shock.
Fabcel pad has been used for over 40 years
for mounting machinery and sensitive
equipment where absorption of impact
shock or isolation of transmitted vibration
is desired. Fabcel pads may be bonded
together (layered) to achieve the desired
isolation eciency for any application.
Part Number
Size (in.)
18 x 18 x 3/8
18 x 36 x 3/8
18 x 18 x 1/2
Size (in.)
Fabcel 25
25
18 x 18 x 5/16
Fabcel 50
50
18 x 18 x 5/16
Fabcel 100
100
18 x 18 x 5/16
Fabcel 200
200
18 x 18 x 1/2
Fabcel 300
300
18 x 18 x 1/2
Part Number
Size (in.)
20 x 20 x 3/8
20 x 20 x 1/4
100
101
Part Number
Size (in.)
12 x 12 x 1
18 x 18 x 1
18 x 36 x 1
Compression Pad
Custom Isolators
Multi-purpose neoprene isolation pads are used to eliminate vibration and transmitted noise.
They oer good phyical strength and high energy-absorbing characteristics.
Part Number
Color Code
Size (in.)
50100
Red
24 x 24 x 1/2
100
52330
Green
24 x 24 x 1/2
200
52331
White
24 x 24 x 1/2
300
52332
Green
12 x 12 x 1/2
200
52333
White
12 x 12 x 1/2
300
52334
Green
12 x 24 x 1/2
200
52335
White
12 x 24 x 1/2
300
52355
Blue-White
36 x 36 x 1/2
300
52746
Black
48 x 48 x 1/2
300
In addition to alternate materials for our standard parts, Tech Products oers
custom isolation products including:
102
103
Contact Information
In addition to our shock and vibration isolators, Tech Products also oers Noise
Control Solutions including:
Phone: 937-438-1100
Fax: 937-438-2190
General Email: tpc@novibes.com
Customer Service: custsvc@novibes.com
Orders: orderdesk@novibes.com
Engineering: engr@novibes.com
Visit www.novibes.com for more information on our our noise control products.
Website: www.novibes.com
104
105
106