Ms. Nirmal kumar pandey/EI/SCC/QB/UNIT- I to V/2013-14 Page 1
Unit-1 Two Marks Q.1 What is the need of swamping resistance. (April-May 2010) Q.2 Define opamp. (April-May 2013,2009) Q.3 List out ideal V/s practical characteristics of IC 741 Op-amp. (Nov.-Dec. 2008) Q.4 What is the significance of DC analysis of op-amp ? (Nov.-Dec. 2012) Seven Marks Q.5 Obtain an expression of voltage gain, input impedance and output impedance of a practical inverting Amplifier. (April-May 2010) Q.6 An Op-amp is used in voltage follower mode having a slew rate of 0.5 V/s. If the amplitude of the sine wave is 7V , find the slew rate limited frequency. Find the peak value of the sinusoidal output voltage that can be produced if Op-amp circuit has closed loop gain of 10. Assume UGB of Op-amp as 800 KHz. (April-May 2010) Q.7 Explain all parameters of opamp with their practical values. (April-May 2009) Q.8 Discuss closed loop differential amplifiers configuration with opamp & also derive an expression for its voltage gain. (April-May 2009) Q.9 An opamp has a differential gain of 80 dB and CMRR of 95 dB. If V 1 = 2V and V 2 = 1.6V, then calculate the differential and common mode output values. (April-May 2009) Q.10 Explain the types of frequency compensation techniques used in Op-amps ? (Nov.-Dec. 2008) Q.11 Explain block diagram of a typical operational amplifier. (Nov.-Dec. 2008) Q.12 Derive the expression for voltage gain of inverting amplifier. (Nov.-Dec. 2008) Q.13 Explain why open-loop op-amp configuration are not used in linear applications. (April-May 2008) Q.14 What are the three factors that affect the electrical parameters of an op-amp ? (April- May 2008) Q.15 What is a voltage transfer curve of an op-amp ? (April-May 2008) Q.16 For a practical inverting amplifier using op-amp derive the expression for the input and output resistance with feedback. (Nov.-Dec. 2007) Q.17 Draw the block diagram of opamp and explain in detail. (April-May 2013) Q.18 Write the ideal characteristics of opamp. (April-May 2013) Q.19 Describe open-loop and closed loop configuration of opamp. (April-May 2013) SIGNAL CONDITIONING CIRCUITS QUESTION BANK
Ms. Nirmal kumar pandey/EI/SCC/QB/UNIT- I to V/2013-14 Page 2
Q.20 Give the difference between the ideal and practical characteristics of op-amp ? (Nov.- Dec. 2012) Q.21 Do the AC analysis of op-amp for: Differential gain, Common mode gain, CMRR, Differential input impedance, output impedance. (Nov.-Dec. 2012) ------------------------------------------------------------------------------------------------------------------------------
UNIT-2 Two Marks Q.1 What is voltage follower ? (April-May 2013,2010, 2009) Q.2 What is the difference between comparators and Op-amps ? (Nov.-Dec. 2008) Q.3 Why we called the voltage follower as a isolation amplifier ? (Nov.-Dec. 2012) Seven Marks Q.1 Explain instrumentation amplifier ? (April-May 2013, 2010) Q.2 Explain temperature compensated logarithmic amplifier. Why it is necessary. (April- May 2010) Q.3 Show with the help of circuit diagram an Op-amp used as : i. Scale changer ii. Phase shifter iii. Inverting adder iv. Non inverting adder. (April-May 2010) Q. 4 Explain the subtractor using opamp & derive its formula for output voltage. (April-May 2009) Q.5 Write a short note on Window Detector. (April-May 2009) Q.6 Design a practical integration circuit with a d.c. gain of 10, to integrate a square wave of 10 KHz. (April-May 2009) Q.7 Explain the op-amp as zero crossing detector. (Nov.-Dec. 2008) Q.8 Explain the op-amp as integrator circuit. (Nov.-Dec. 2008) Q.9 Explain the op-amp as logarithmic amplifier. (Nov.-Dec. 2008) Q.10 What are the three differential amplifier configuration? Briefly compare and contrast these configurations. (April-May 2008) Q.11 What is a feedback? List two types of feedback. Which type is used in linear applications? (April-May 2008) SIGNAL CONDITIONING CIRCUITS QUESTION BANK
Ms. Nirmal kumar pandey/EI/SCC/QB/UNIT- I to V/2013-14 Page 3
Q.12 What do you mean by zero crossing detector? Explain the zero crossing detector as a time markers generator from a sine wave. (Nov.-Dec. 2007) Q.13 Explain the working and different uses of Bootstrap Amplifier. (Nov.-Dec. 2007) Q.14 Explain the operation of integrator with its derivation and waveform. (April-May 2013) Q.15 Describe the operation of summer circuit. (April-May 2013) Q.16 Design a practical integrator circuit with DC gain of 10, to integrate a square wave of 10 KHz ? (Nov.-Dec. 2012) Q.17 Prove that: V o = - (ER)/ (R 1 + R ref ) (Nov.-Dec. 2012) Q.18 Design a three op-amp instrumentation amplifier to vary a gain from 1 to 10000. (Nov.-Dec. 2012)
UNIT-3 Two Marks Q.1 What is the need of voltage sweep generator ? (April-May 2010) Q.2 Define clipper circuit. (April-May 2009) Q.3 Explain the terms displacement error and transmission error. (Nov.-Dec. 2008) Q.4 What is substitute name of square-wave generator ? (Nov.-Dec. 2012)
Seven Marks Q.1 Explain the operation of square wave generator by drawing the output voltage waveforms ? (April-May 2010) Q.2 Explain the following : i. High pass RC circuit as differentiator ii. Low pass RC circuit as integrator. (April-May 2010) Q.3 How can high pass RC circuit used as a differentiator? Explain it. (April-May 2009) Q.4 Explain the positive clamper circuits with its circuit diagram & waveforms. (April- May 2009) Q.5 What do you understand by current sweep generator? Write its application also. (April-May 2009) Q.6 Explain the operation of Miller sweep circuit and derive an expression for slope error. (Nov.-Dec. 2008) SIGNAL CONDITIONING CIRCUITS QUESTION BANK
Ms. Nirmal kumar pandey/EI/SCC/QB/UNIT- I to V/2013-14 Page 4
Q.7 Explain the circuit of Triangular wave generator along with all waveform and derivation of output frequency. (Nov.-Dec. 2008) Q.8 Explain positive and negative clampers along with circuit diagrams. (Nov.-Dec. 2008) Q.9 What is thermal drift? How does it affect the performance of an op-amp circuit? (April-May 2008) Q.10 What is an electrical noise? What precautions can be taken to minimize the effect of noise on an op-amp circuit? (April-May 2008) Q.11 Explain the working of series and parallel clipper with suitable diagram. (Nov.- Dec. 2007) Q.12 What do you mean by voltage sweep generator and current sweep generator. Explain them. Write their application. (Nov.-Dec. 2007) Q.13 Explain the circuit diagram of triangular wave generator. (April-May 2013) Q.14 What is clamper? Explain the types of clamper. (April-May 2013) Q.15 Write short notes on Schmitt trigger. (April-May 2013) Q.16 What is difference between comparator and Schmitt trigger ? (Nov.-Dec. 2012) Q.17 Explain the working of negative peak clamper. (Nov.-Dec. 2012) Q.18 Design the triangular wave generator so that fo = 2KHz and Vo (pp) = 7V supply voltage of op-amp is = 15V. Assume vsat = 14V. (Nov.-Dec. 2012) -------------------------------------------------------------------------------------------------------------------------------
UNIT-4 Two Marks Q.1 What is speed up capacitor ? (April-May 2010) Q.2 What is multivibrator? (April-May 2009) Q.3 What are the methods of triggering? Give name. (Nov.-Dec. 2008) Q.4 Name the types of multivibrator. (April-May 2013) Q.5 For a particular power supply the load voltage is 10V 0.3V for a line voltage of 230V 10%. Calculate source regulation and percentage source regulation. (Nov.-Dec. 2012) Seven Marks Q.1 Explain the Schmitt trigger ( Emitter coupled binary) with proper waveform. (April-May 2010) Q.2 Explain collector coupled Astable Multivibrator with a proper circuit diagram. Also Derive: f o = 1/ (1.38 RC). (April-May 2013, 2010) SIGNAL CONDITIONING CIRCUITS QUESTION BANK
Ms. Nirmal kumar pandey/EI/SCC/QB/UNIT- I to V/2013-14 Page 5
Q.3 With circuit diagram, explain the working of Emitter coupled monostable multivibrator. (April-May 2009) Q.4 Write a short note on Commutating Capacitors. (April-May 2013, 2009) Q.5 Design an astable multivibrator. The repetition rate is 500 Hz and pulse width is 0.2 ms. Use two transistors with hfe = 50, Vcc = VBB = 20 V, Rc1 = Rc1= 1K. (April-May 2009) Q.6 Explain in detail the significance of commutating capacitors in binary. Derive an expression for maximum frequency of operation of binary using commutating capacitors. (Nov.-Dec. 2008) Q.7 Explain the method of improving the resolution of Bistable multivibrators along with the circuit diagram. (Nov.-Dec. 2008) Q.8 What is the difference between clippers and clampers? Give one application of each. (April-May 2008) Q.9 List one application each in which the 555 can be used as a monostable & astable multivibrator. (April-May 2008) Q.10 Explain the working of Schmitt trigger with the help of Timer 555 IC. (Nov.-Dec. 2007) Q.11 How square wave can be generated with Timer 555 IC? (Nov.-Dec. 2007) Q.12 Explain the circuit for gated astable multivibrator. (Nov.-Dec. 2007) Q.13 Expalin the circuit diagram of emitter coupled astable multivibrator. (April-May 2013) Q.14 Derive the expression for current boosting. (Nov.-Dec. 2012) Q.15 Write short notes on : (a) Thermal shutdown (b) Over voltage protection circuit. (Nov.-Dec. 2012) Q.16 Give the difference between linear and switched mode regulator ? (Nov.-Dec. 2012)
UNIT-5 Two Marks Q.1 Draw the pin diagram of IC-555. (April-May 2010) Q.2 Define regulator. (April-May 2009) Q.3 Define Duty cycle. (Nov.-Dec. 2008, April-May 2013) Q.4 What is multivibrator ? (Nov.-Dec. 2012)
Seven Marks
Q.1 Explain IC-723 as high voltage and low voltage regulator. (April-May 2010) Q.2 Explain 555 Timer used as a astable multivibrator with proper functional block diagram. (April-May 2010) SIGNAL CONDITIONING CIRCUITS QUESTION BANK
Ms. Nirmal kumar pandey/EI/SCC/QB/UNIT- I to V/2013-14 Page 6
Q.3 Explain Shunt Regulator using Op-amp. (April-May 2010) Q.4 Explain with neat sketch, the working of monostable multivibrator, derive its expression for pulse width. (April-May 2013, 2009) Q.5 Design an astable multivibrator to generate the output signal with frequency of 1 kHz and the duty cycle of 75%. (April-May 2009) Q.6 Compare between Shunt and Series Regulators. (April-May 2009) Q.7 Explain function of 555 Timer in monostable mode. Give proper function block diagram and waveforms. Obtain the equation T = 1.1 RC, for the pulse duration. (Nov.-Dec. 2008) Q.8 Draw the block diagram of shunt regulator and explain it. (Nov.-Dec. 2008) Q.9 Design an adjustable regulator using LM 317 which will satisfy the requirements as output voltage 7 to 15 V output 1A. (Nov.-Dec. 2008) Q.10 What is voltage regulator? List four different types of voltage regulators. (April-May 2008) Q.11 Briefly explain the difference between the two operating modes of the 555 timer. (April-May 2008) Q.12 What are the advantages of the adjustable voltage regulators over the fixed voltage regulator? (April-May 2008) Q.13 Describe shunt regulator using Op-amp. (Nov.-Dec. 2007) Q. 14 An exponential sweep results when capacitor is charged from supply voltage V through resistor. If the peak sweep voltage is V s , prove that : e s = V s / V . (Nov.-Dec. 2007) Q.15 Write short notes on any two: i. Three terminal IC regulator ii. VCO iii. Protection Circuits. (Nov.-Dec. 2007) Q.16 Mention the applications of astable multivibrator (using IC 555). (April-May 2013) Q.17 Draw the block diagram of voltage regulators and explain it in brief. (April-May 2013) Q.18 How the commutating capacitor play important role in multivibrator ? (Nov.-Dec. 2012) Q.19 Explain the working of collector coupled astable multivibrator with suitable waveform? (Nov.-Dec. 2012) Q.20 Describe the working of emitter coupled binary ? (Nov.-Dec. 2012)
IBL Programme EXAMINATION, 2013 (July) B.Sc. Honors Physics (Part-II) PAPER I: Electronics Time: Three Hours Maximum Marks: 100 Attempt Any FIVE Questions. All Questions Carry Equal Marks