BII 40030 Accessory User's Information Manual 2 of 25 08E92-STX-2A00-91 installation INSTRUCTIONS. ANTENNA 2 BLACK RELAYS (4-PIN) Control Unit green relay (5-PIN).
BII 40030 Accessory User's Information Manual 2 of 25 08E92-STX-2A00-91 installation INSTRUCTIONS. ANTENNA 2 BLACK RELAYS (4-PIN) Control Unit green relay (5-PIN).
BII 40030 Accessory User's Information Manual 2 of 25 08E92-STX-2A00-91 installation INSTRUCTIONS. ANTENNA 2 BLACK RELAYS (4-PIN) Control Unit green relay (5-PIN).
2008 American Honda Motor Co., Inc. - All Rights Reserved.
BII 40030 (0807) 1 of 25 08E92-STX-2A00-91
INSTALLATION INSTRUCTIONS Accessory Application Publications No. Issue Date REMOTE CONTROL ENGINE STARTER PARTS LIST Remote Engine Starter Unit Kit P/N 08E91-E22-200B Remote Control Engine Starter Attachment Kit P/N 08E92-STX-200A JULY 2008 2009 MDX Transmitter Control unit Key ring Protective tape Antenna Engine starter harness Engine starter sub harness Control unit bracket Template Fuse label Caution label 2 Black relays (4-pin, black) Green relay (5-pin, green) BII 40030 Accessory Users Information Manual 2 of 25 BII 40030 (0807) 2008 American Honda Motor Co., Inc. - All Rights Reserved. TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Flat-tip screwdriver Small flat-tip screwdriver Ratchet 10 mm and 14 mm Sockets Combination wrench Isopropyl alcohol Shop towel Needle nose pliers Scale Tape measure Scissors Rubber mallet HDS (Honda Diagnostic System) Masking tape Clip remover NOTE: This antenna should only be installed if the ambient air temperature 15C (60F) or above. 1. Make sure you have the anti-theft code for the radio, then write down the radio station presets. 2. Disconnect the negative cable from the battery. INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. Illustration of the Engine Starter Installed on the Vehicle 28 Wire ties Clip 5 Foam cushion tapes Flange bolt Fuse (3 A) 6D01150H ANTENNA 2 BLACK RELAYS (4-PIN) CONTROL UNIT GREEN RELAY (5-PIN) ENGINE STARTER HARNESS ENGINE STARTER SUB HARNESS 3 A FUSE 40 A FUSE BLOCK 2008 American Honda Motor Co., Inc. - All Rights Reserved. BII 40030 (0807) 3 of 25 4. Using a small plastic trim tool and a shop towel, remove the map light (one retaining clip, two retaining tabs, and unplug the two vehicle connectors). 6319032S MAP LIGHT RETAINING TABS VEHICLE CONNECTORS RETAINING CLIP SHOP TOWEL PLASTIC TRIM TOOL PROTECTIVE TAPE CONTROL UNIT ADHESIVE BACKING Clean with isopropyl alcohol. SWITCH Setting the Control Unit 3. Set the control unit switches as shown. Using an isopropyl alcohol on a shop towel, clean the area where the protective tape will attach. Attach the protective tape to the control unit over the switches. When the switch setting is not correct, the engine starter will not start. For switch setting, first touch a metal part of the car to discharge any static electricity, and then perform the setting. SW: 1 RR Junction SW: 2 Trunk or Tailgate SW: 3 Smart Entry SW: 4 Horn or Buzzer Answerback SW: 5 Trunk Main SW SW: 6 Reserve 4 of 25 BII 40030 (0807) 2008 American Honda Motor Co., Inc. - All Rights Reserved. 5N23061H 2 CLIPS LEFT FRONT A-PILLAR TRIM 9. Remove the left front pillar trim (two clips). 7. Pull away the weatherstrip from the left front pillar trim. 8. Using a rubber mallet and a shop towel, gently strike the area shown of the left front pillar trim to release the clip. 5N23054H WEATHERSTRIP Strike perpendicularly to the vehicle. CLIP STRIKE POINT RUBBER MALLET SHOP TOWEL LEFT FRONT A-PILLAR TRIM PIN LEFT FRONT PILLAR LEFT FRONT PILLAR TRIM CLIP PIN Approx. 16 mm (0.6 in.) 5. Remove the roof console (four screws). 6. Remove the sunvisor holders. Using a flat-tip screwdriver, push the hook, and turn the holder 90, then pull it out. 7201010H ROOF CONSOLE 4 SCREWS ROOF CONSOLE SCREWS 6411011H SUNVISOR HOLDER FLAT-TIP SCREWDRIVER Push. Turn. 2008 American Honda Motor Co., Inc. - All Rights Reserved. BII 40030 (0807) 5 of 25 12. Pull away the weatherstrip and remove the passengers dashboard side cover (six retaining tabs). 13. Using a flat-tip screwdriver and a shop towel, remove the drivers outer dashboard trim (four clips and vehicle connectors). 6412011H 4 RETAINING TABS 2 RETAINING TABS PASSENGERS DASHBOARD SIDE COVER WEATHERSTRIP 6412022H 4 CLIPS DRIVERS OUTER DASHBOARD TRIM VEHICLE CONNECTORS SHOP TOWEL FLAT-TIP SCREWDRIVER 11. Turn the knob counterclockwise, then pull out the drivers dashboard under cover (one clip and two pins). Release the vehicle harness clip and unplug the two vehicle connectors to remove the drivers dashboard under cover. 5N23104H KNOB 2 VEHICLE CONNECTORS PIN PIN VEHICLE HARNESS CLIP CLIP DRIVERS DASHBOARD UNDER COVER 10. Remove and discard the clip from the left front A-pillar, and install a new clip on the left front A- pillar trim. 5N23072H CLIP (Discard.) LEFT FRONT PILLAR NEW CLIP LEFT FRONT PILLAR TRIM 6 of 25 BII 40030 (0807) 2008 American Honda Motor Co., Inc. - All Rights Reserved. 16. Release the drivers center console trim (eight clips) as shown below. 17. Remove the right front door side sill trim (four clips and six retaining tabs). 14. Using a flat-tip screwdriver and a shop towel, remove the drivers center trim (five clips and three retaining tabs). 15. Remove the drivers lower dashboard cover (one self-tapping screw and nine clips). If equipped, remove the A/C sensor (two retaining tabs). 5N14051S DRIVERS INNER DASHBOARD TRIM 3 RETAINING TABS 5 CLIPS FLAT-TIP SCREWDRIVER SHOP TOWEL 7201021H 2 CLIPS DRIVERS CENTER CONSOLE TRIM 6 CLIPS 5N24051H 6 RETAINING TABS 4 CLIPS RIGHT FRONT DOOR SIDE SILL TRIM FRONT 6412033H 9 CLIPS SELF- TAPPING SCREW DRIVERS DASHBOARD LOWER COVER A/C SENSOR 2 RETAINING TABS A/C SENSOR 2008 American Honda Motor Co., Inc. - All Rights Reserved. BII 40030 (0807) 7 of 25 18. Remove the passengers dashboard under cover (five clips, and release two pins and two vehicle connectors). 19. Pull away the weatherstrip, and remove the right kick panel (two clips). 5N14011S PASSENGERS DASHBOARD UNDER COVER 5 CLIPS 2 PINS 2 VEHICLE CONNECTORS Installing the Antenna 20. Wrap three pieces of urethane foam around the antenna cable at the measurements shown. 21. Using scissors, cut one urethane foam in half. Wrap the two halves of the urethane foam around the antenna cable at the measurements shown. 5N24030H CLIP WEATHERSTRIP RIGHT KICK PANEL CLIP 6412052H URETHANE FOAM HALF URETHANE FOAM ANTENNA CABLE 380 mm (15 in.) Cut. 30 mm (1.2 in.) 730 mm (29 in.) URETHANE FOAM ANTENNA 8 of 25 BII 40030 (0807) 2008 American Honda Motor Co., Inc. - All Rights Reserved. 24. Secure the template to the windshield with the tape by aligning it with the edge of the black ceramic paint as shown. 22. Measure and mark the antenna plate using two pairs of neddle nose pliers, bend the antenna plate to the angle shown. 23. Using scissors, cut out the template. 7201041H Cut out. TEMPLATE 7201031H ANTENNA 15 mm (0.6 in.) ANTENNA PLATE SCALE 14 mm (0.6 in.) ANTENNA PLATE NEEDLE NOSE PLIERS 7802020H WINDSHIELD BLACK CERAMIC PART TEMPLATE TAPE REARVIEW MIRROR 2008 American Honda Motor Co., Inc. - All Rights Reserved. BII 40030 (0807) 9 of 25 28. Gently pull down the roof lining, and tuck the antenna cable under it. Be careful not to crease the roof lining. 29. Route the antenna cable down the A-pilar along the vehicle harness. 30. Pull away the weatherstrip. Route the antenna cable down under the dashboard. Tuck the antenna cable between the left front A-pillar and the dashboard, and reinstall the weatherstrip. 25. Using isopropyl alcohol on a shop towel, clean the area where the antenna will attach. 26. Remove the adhesive backing from the antenna. Insert the antenna plate over the roof liner, and attach the antenna to the windshield aligning it with the template. 27. Remove the template. 6412080H TEMPLATE ADHESIVE BACKING Clean with isopropyl alcohol. ROOF LINER ANTENNA PLATE 7201050H ROOF LINER ANTENNA CABLE VEHICLE HARNESS LEFT FRONT A-PILLAR 7509010H DASHBOARD LEFT FRONT PILLAR ANTENNA CABLE WEATHERSTRIP 10 of 25 BII 40030 (0807) 2008 American Honda Motor Co., Inc. - All Rights Reserved. 35. At the dashboard area, secure the antenna cable to the vehicle harness with one wire tie. Routing the Engine Starter Harness 36. Install the three relays to the engine starter harness relay blocks. Be careful to install the relays properly to avoid a malfunction. 37. Attach the 40 A ENG STARTER fuse label to the engine starter harness fuse block. 6413050H VEHICLE HARNESS ANTENNA CABLE WIRE TIE 31. Using isopropyl alcohol on a shop towel, clean the roof panel where the urethane foam will attach. 7201060H ANTENNA CABLE VEHICLE HARNESS WIRE TIE URETHANE FOAM 6413060H 2 BLACK RELAYS (4-PIN) ENGINE STARTER HARNESS GREEN RELAY (5-PIN) 40 A ENG STARTER FUSE LABEL RELAY BLOCK FUSE BLOCK 34. Along the front A-pillar, secure the antenna cable to the vehicle harness with four wire ties. 32. Secure the antenna cable to the vehicle harness with one wire tie. 33. Secure the antenna cable to the roof panel with one urethane foam in the areas shown. 6413040H VEHICLE HARNESS ANTENNA CABLE 4 WIRE TIES LEFT FRONT PILLAR 2008 American Honda Motor Co., Inc. - All Rights Reserved. BII 40030 (0807) 11 of 25 42. Plug the engine starter harness 6-pin connector (blue) into the fuse box. 43. Reconnect the two vehicle connectors unplugged in step 38. 38. At the fuse box, locate and unlock the two vehicle connectors and disconnect them from the fuse box. 39. Unplug the vehicle 6-pin connector (green) from the fuse box. 40. Secure the clip on the engine starter harness to the fuse box as shown. 7201080H CLIP ENGINE STARTER HARNESS FRONT FUSE BOX 7201070H FUSE BOX 2 VEHICLE CONNECTORS LOCK VEHICLE 6-PIN CONNECTOR (GREEN) 41. Plug the engine starter harness 6-pin connector (green) into the fuse box, and plug the vehicle 6-pin connector into the engine starter harness 6-pin connector (green). NOTICE Check that the engine starter harness 6-pin connectors (green) are connected to the fuse box and vehicle connector, and they are locked securely. Loose connectors can cause engine stall during driving. 7201091H VEHICLE 6-PIN CONNECTOR (GREEN) ENGINE STARTER HARNESS 6-PIN CONNECTOR (BLUE) ENGINE STARTER HARNESS 6-PIN CONNECTOR (GREEN) FUSE BOX Pull the connector and check for securely locking. 12 of 25 BII 40030 (0807) 2008 American Honda Motor Co., Inc. - All Rights Reserved. 47. Near the steering wheel shaft, locate and unplug the vehicle 20-pin and 14-pin connectors: First unplug the inside 20-pin connector (small), then unplug the outside 14-pin connector (large). 45. Remove the vehicle control unit (one bolt), and let the control unit hang. 46. Route the two engine starter harness 14-pin connectors over the steering shaft. 6414051H BOLT VEHICLE CONTROL UNIT STEERING SHAFT 7205010H 2 ENGINE STARTER HARNESS 14-PIN CONNECTORS ENGINE STARTER HARNESS TOP VIEW STEERING SHAFT 7508010H VEHICLE 22-PIN CONNECTOR VEHICLE 14-PIN CONNECTOR (WHITE) STEERING SHAFT 6414030H ENGINE STARTER HARNESS RELAY BLOCK VEHICLE RELAY BLOCK 44. Attach the engine starter harness relay block to the vehicle relay block as shown. 2008 American Honda Motor Co., Inc. - All Rights Reserved. BII 40030 (0807) 13 of 25 Reconnect the 20-pin connector. This connector was unplugged to access the lock on the 14-pin connector. Plug the engine starter harness 14-pin connector in between the vehicle 14-pin connectors. Slide the holder on the side of the engine starter harness onto the holder lock on the vehicle 14-pin connector. 7508020H VEHICLE 22-PIN CONNECTOR VEHICLE 22-PIN CONNECTOR VEHICLE 14-PIN CONNECTOR VEHICLE 14-PIN CONNECTOR ENGINE STARTER HARNESS 14-PIN CONNECTOR 48. Secure the engine starter harness connector to the vehicle harness with two wire ties. 6417020H ENGINE STARTER HARNESS VEHICLE HARNESS 2 WIRE TIES STEERING SHAFT 6417031H ENGINE STARTER HARNESS VEHICLE HARNESS WIRE TIES 49. Reinstall the vehicle control unit with the bolt removed in step 45. Be sure the engine starter harness is above the control unit. 50. Secure the engine starter harness to the vehicle harness with three additional wire ties. HOLDER HOLDER LOCK 14 of 25 BII 40030 (0807) 2008 American Honda Motor Co., Inc. - All Rights Reserved. 55. Secure the engine starter harness and antenna cable to the plastic dashboard frame with three wire ties. 54. At the center console, route the engine starter harness 12-pin connector and antenna cable down along the vehicle harness to the drivers center console trim opening. 51. Secure the engine starter harness connector to the vehicle harness with one wire tie. Near the relays secure the engine starter harness to the vehicle harness with one wire tie. 53. Route the engine starter harness 12-pin connector and antenna cable along the dashboard frame towards the center counsole. 52. Secure the engine starter harness and antenna cable to the vehicle harness with one wire tie. 7205020H ENGINE STARTER HARNESS WIRE TIE VEHICLE HARNESS WIRE TIE ANTENNA CABLE WIRE TIE ENGINE STARTER HARNESS CONNECTOR RELAYS 6D01042H ENGINE STARTER HARNESS 12-PIN CONNECTOR ANTENNA CABLE VEHICLE HARNESS DRIVERS CENTER CONSOLE TRIM OPENING 6417070H ENGINE STARTER HARNESS ANTENNA CABLE PLASTIC DASHBOARD FRAME PLASTIC DASHBOARD FRAME WIRE TIES WIRE TIE 7205030H ENGINE STARTER HARNESS 12-PIN CONNECTOR PLASTIC DASHBOARD FRAME ANTENNA CABLE 2008 American Honda Motor Co., Inc. - All Rights Reserved. BII 40030 (0807) 15 of 25 56. Secure the engine starter harness and antenna cable to the vehicle harness with one wire tie. 6D01050H VEHICLE HARNESS WIRE TIE ANTENNA CABLE ENGINE STARTER HARNESS WIRE TIE Routing the Engine Starter Subharness 57. At the passenger's kick panel (removed in step 19), slide the holder on the engine starter subharness 34-pin connector onto the holder lock on the vehicle 5-pin connector. 58. Unplug the vehicle 34-pin connector and plug the engine starter subharness 34-pin connectors in between. 6418020H ENGINE STARTER SUBHARNESS 34-PIN CONNECTOR RIGHT FRONT LOWER PILLAR VEHICLE 34-PIN CONNECTOR VEHICLE 6-PIN CONNECTOR 16 of 25 BII 40030 (0807) 2008 American Honda Motor Co., Inc. - All Rights Reserved. 62. Pull the end of the passengers center console trim to release the one clip shown. Route the engine starter subharness along the vehicle harness to the driver center console trim opening. NOTE: Pulling the passenger console trim too much causes damage. 59. Remove the vehicle ground bolt. Attach the engine starter subharness ground terminal, and reinstall the ground bolt you just removed. 6418030H ENGINE STARTER SUBHARNESS GROUND TERMINAL WIRE TIES VEHICLE HARNESS GROUND BOLT (Reuse.) ENGINE STARTER SUBHARNESS 60. Secure the engine starter subharness to the vehicle harness with two wire ties. 61. Route the engine starter subharness under the blower motor, and along the vehicle harness towards the center console. 6418040H ENGINE STARTER SUBHARNESS VEHICLE HARNESS BLOWER MOTOR 6D01060H END OF PASSENGERS CENTER CONSOLE TRIM ENGINE STARTER SUB HARNESS VEHICLE HARNESS FRONT CLIP DRIVERS CENTER CONSOLE TRIM OPENING TOP VIEW PASSENGERS CENTER CONSOLE TRIM Do not pull too much. 2008 American Honda Motor Co., Inc. - All Rights Reserved. BII 40030 (0807) 17 of 25 63. Secure the engine starter subharness to the vehicle harness with four wire ties in the areas shown. 64. Behind the center console, secure the engine starter subharness to the vehicle harness with one wire tie. 6418061H VEHICLE HARNESS ENGINE STARTER SUBHARNESS WIRE TIES 6D01070H VEHICLE HARNESS ENGINE STARTER SUBHARNESS WIRE TIE 18 of 25 BII 40030 (0807) 2008 American Honda Motor Co., Inc. - All Rights Reserved. 68. Plug the engine starter subharness 12-pin connector into the engine starter harness 12-pin connector. 67. Connect the antenna lead to the control unit as shown. 6D01124H FRONT ANTENNA LEAD CONTROL UNIT 6D01134H CONTROL UNIT ENGINE STARTER SUBHARNESS 12-PIN CONNECTOR ENGINE STARTER HARNESS 12-PIN CONNECTOR FRONT Installing the Control Unit 65. Install the clip of the engine starter subharness to the engine starter unit bracket as shown. 66. Install the engine starter unit bracket and plug the engine starter subharness 28-pin connector into control unit. Note the direction of the bracket. 7508030H ENGINE STARTER UNIT BRACKET ENGINE STARTER SUBHARNESS CLIP 6D01082H CONTROL UNIT ENGINE STARTER UNIT BRACKET ENGINE STARTER SUB HARNESS 28-PIN CONNECTOR 2008 American Honda Motor Co., Inc. - All Rights Reserved. BII 40030 (0807) 19 of 25 With AC inverter unit 69. Install the engine starter unit bracket to the vehicle bracket using a flange bolt. If the AC inverter unit is mounted on the vehicle bracket, install the engine starter unit and bracket to the vehicle bracket reusing the vehicle bolt fastening the AC inverter unit. Without AC inverter unit 6D01094H FLANGE BOLT ENGINE STARTER UNIT BRACKET VEHICLE BRACKET VEHICLE BRACKET ENGINE STARTER UNIT BRACKET 6D01104H VEHICLE BOLT (reused) AC INVERTER UNIT ENGINE STARTER UNIT BRACKET AC INVERTER UNIT 70. Install the clip on the engine starter subharness, 12-pin connector to the engine starter unit bracket as shown. 7205042H ENGINE STARTER UNIT BRACKET CLIP ENGINE STARTER SUBHARNESS ENGINE STARTER HARNESS 12-PIN CONNECTOR 20 of 25 BII 40030 (0807) 2008 American Honda Motor Co., Inc. - All Rights Reserved. 75. Using isopropyl alcohol on a shop towel, clean the areas where the caution label will attach. 6419072H HOOD CAUTION LABEL ADHESIVE BACKING Clean with isopropyl alcohol. 74. Attach the 3 A ENG STARTER fuse label to the No.33 slot on the inside of the fuse box lid. 6419060H 3 A ENG STARTER FUSE LABEL FUSE BOX LID No.33 73. Install the 3 A fuse from in the kit into the No. 33 slot of the fuse box. 7205050H FUSE BOX 3 A FUSE 71. Secure the engine starter harness, engine starter subharness, and antenna cable to the vehicle harness with three wire ties as shown. Bundle the excess antenna cable and secure it using one wire tie as shown. 72. Remove the fuse box lid. 6D01143H VEHICLE HARNESS ANTENNA CABLE ENGINE STARTER HARNESS 3 WIRE TIES ENGINE STARTER SUBHARNESS Bundle the excess antenna cable. 7206010H FUSE BOX LID LEFT KICK PANEL 2008 American Honda Motor Co., Inc. - All Rights Reserved. BII 40030 (0807) 21 of 25 76. Attach the caution label to the under side of the hood. 77. Check that all wire harnesses and cables are routed properly and that all connectors are plugged in. 78. Reinstall all removed parts. Check that all clips and other fasteners are installed securely. 79. Reconnect the negative cable to the battery. Check that the electrical accessory and other electrical systems function properly. 80. Enter the clients radio anti-theft code, and reset the radio station presets. 81. Reset the clock. 82. Perform REMOTE ENGINE STARTER REGISTRATION and FUNCTION CHECK. 752501AS CAR ICON REMOTE ENGINE STARTER REGISTRATION 1. Acquire the PCM Code from the Interactive Network. 2. Connect the HDS tester to the OBD II data link connector, then turn the ignition switch on. 3. Start the HDS, and clis in accordance with the HDS, then click the check button. OBD II DATA LINK CONNECTOR HDS TESTER 4. Start the HDS, and clis in accordance with the HDS, then click the check button. 752502AS CHECK BUTTON Input the VIN and other requirements. 22 of 25 BII 40030 (0807) 2008 American Honda Motor Co., Inc. - All Rights Reserved. 752504AS Select the R/C ENG STARTER. CHECK BUTTON 752503AS Select the Honda Systems. CHECK BUTTON 752505AS Check that REMARKS is shown. CHECK BUTTON 752506AS Select the REGISTER REMOTE CONTROL ENGINE STARTER UNIT. CHECK BUTTON 5. Select the Honda Systems, then click the check button. 6. Select the R/C ENG STARTER and click the check button. 7. Check that REMARKS is shown, then click the check button. 8. Select the REGISTER REMOTE CONTROL ENGINE STARTER UNIT, then click the check button. 2008 American Honda Motor Co., Inc. - All Rights Reserved. BII 40030 (0807) 23 of 25 752507AS Check that Obtain PCM-code (IMMOBILIZER PCM CODE) from iN. This vehicles VIN will be required to obtain the password. (USA) is shown. CHECK BUTTON 752509AS Input the PCM Code. CHECK BUTTON 752510AS Check that The registration of the Remote Control Engine Starter Unit has been completed is shown. CHECK BUTTON 752511AS Check that Check that the engine can be started by the Transmitter is shown. CHECK BUTTON 9. Check that Obtain PCM-code (IMMOBILIZER PCM CODE) from iN. This vehicles VIN will be required to obtain the password. (USA) is shown, then click the check button. 10. Input the PCM Code, then click the check button. NOTE: To ensure security, the PCM code (password) is changed everyday, so it is impossible to register the remote controlled engine starter if the date of the PCM code acquisition and registration are different. The date of the HDS tester should also be the same. 11. Check that The registration of the Remote Control Engine Starter Unit has been completed is shown, then click the check button. 12. Check that Check that the engine can be started by the Transmitter is shown, then click the check button. 13. Perform the function test on the next page, then remove the HDS. 24 of 25 BII 40030 (0807) 2008 American Honda Motor Co., Inc. - All Rights Reserved. 732904AY DISPLAY COMMAND BUTTON START BUTTON TRANSMITTER STOP BUTTON FUNCTION CHECK Operating Conditions Hood is closed Shift lever in park The key is out of the ignition All doors and tailgate closed and locked Inspection 1. Within 1 second, press the command button, and then the start button on the transmitter. The engine should start if all operating conditions are met. Does the engine start? 2. Press the command button on the transmitter, and within 1 second, press the stop button. The engine should stop. Does the engine stop? 3. After the engine has stopped, start the engine again, and check that the engine stops after each of the following conditions: NOTE: After each test the ignition key must be cycled, or the drivers door must be opened and closed. Move the shift lever out of the P position. Unlock or open the doors or the tailgate. Open the hood. Insert the key in the ignition. Press on the brake pedal. 4. Check that the power window or the moonroof does not function and the shift lever does not move to any position but the P position when the engine is started with the transmitter. 5. Press the command button on the transmitter two times and check the vehicle condition on the display. 6. Check the operation of the transmitter when the vehicle is 100 m to 150 m (325 to 490 ft.) away, and in direct sight. Does the engine stop after each of these tests? Yes - Operation is normal. No - Check the engine starter harness connections. Yes - Operation is normal. No - Check the engine starter harness connections. Yes - Operation is normal. No: Make sure all Operating Conditions are met. Check the engine starter harness connections. Connect the HDS and check for an indicated failure. (Refer to the appropriate service manual for details.) 2008 American Honda Motor Co., Inc. - All Rights Reserved. BII 40030 (0807) 25 of 25 6. Check the operation of the transmitter when the vehicle is 100 m to 150 m (325 to 490 ft.) away, and in direct sight. How to Program an Sdditional Transmitter 1. Connect the HDS to the data link connector. 2. Start the HDS and click on the car icon. 3. Input the vehicle's VIN and other required information. 4. Select Honda Systems. 5. Select R/C Engine Starter. 6. Select REGISTER NEW TRANSMITTER. 7. When "Ready to program the new transmitter" shows, select ENTER. 8. Press and release the Command button. 9. Press and release the Stop button. 10. Preform the function check on both transmitters. NOTE: Only 2 remotes can be stored in the system's memory.