You are on page 1of 3

Indra Sidharta

Klampis Aji 2 No. 4 Nationality: Indonesian


Surabaya 60117, Indonesia Date of Birth: 19 June 1980
Phone: +62 31 594 1263
E-mail: sidarta@me.its.ac.id
indraz_m42@yahoo.co.uk
Gender: Male
Marital status: Married




Education:

MSc., Joint European Master on Material Science, June 2010
Hamburg University of Technology, Hamburg, Germany
Aalborg University, Aalborg, Denmark
Aveiro University, Aveiro, Portugal
Thesis title: Investigation on the grain size development of Mg-Al alloy by Ti
3
SiC
2
and Ti
3
AlC
2

addition
Advisor: Dr. Norbert Hort

ST., Mechanical Engineering, August 2004
Department of Mechanical Engineering
Sepuluh Nopember Instute of Technology (ITS), Surabaya, Indonesia
Thesis title: Application of organic coating as corrosion protection of reinforcing steel in marine
environment
Advisor: Prof. Dr. Sulistijono, DEA

Professional Courses:

NDT Level II for Penetrant Testing/Magnetic Testing, ITS, 2011

Work Experience:

Master thesis scientific project (May 2009 February 2010)
Magnesium Innovation Center, GKSS Research Center, Geesthacht, Germany
Project: Investigation on the grain size development of Mg-Al alloy by Ti
3
SiC
2
and Ti
3
AlC
2

addition

Master course scientific project (August 2008 January 2009)
Department of Mechanical Engineering, Aalborg University, Aalborg, Denmark
Project: Development of uniaxial pressed P/M Inconel 718 nickel based Superalloy using water
atomized powder

Research and teaching assistant (June 2005 now)
Laboratory of Metallurgy, Department of Mechanical Engineering
Sepuluh Nopember Institute of Technology (ITS), Surabaya, Indonesia
Project Experience:

Surveying and data collector in Mechanical Integrity project - PT. Badak NGL, 2005
Non destructive evaluation team member - PTPN X, 2005 - 2006
Trainer of Material Selection Training Course PT. Tjiwi Kimia, 2005
Trainer of Mechanical Testing Training Course Institut Teknologi Padang, 2005
Team member of failure analysis of corrosion in waterpipe PT. Petrokimia Gresik, 2005
PFD and P&ID documenting team PT. Pertamina UPPS V, 2006
Team member for Low Speed bearing Vibration analysis of Coal Terminal Facilities - PT. KPC,
Sangata, 2010
Failure analysis of Tire Kiln, PT. Semen Gresik, Tuban, 2011
PFD and P&ID documenting team PT. Pertamina UBEP Tanjung, 2012
Trainer of Mechanical Engineering - PTPN X, 2012
Trainer of Introduction to Non Destructive Test - PT. PJB, 2012
Trainer of Introduction to Casting Technology East Java Bureau of Industries, 2012
Failure analysis of Tire Kiln Tuban - PT. Semen Gresik, 2012
Bypass stack support structure assessment - PT. Indonesia Power, 2012
Basic design of overhead traveling crane - PT. PJB, 2012
Consultation and supervision of high pressure heater fabrication PT. PJB, 2012
Conveyor structure simulation - PT. Setyawan, 2012
Conveyor structure assessment - PT. Kideco, 2012
Re-engineering deaerator PT. PJB, 2012
Flow assurance analysis on offshore pipeline PT. Pertamina, 2013
Cooling system modification analysis in PLTA Sengguruh - PJB UP. Brantas, 2013
Redrawing Oil Box in PLTA Sutami - PJB UP Brantas, 2013
RCFA analysis on bottom ash heat exchanger #2B - PJB UP Paiton, 2013
Engineering design on bypass drain for high pressure heater - PJB UP Paiton, 2013
Reverse engineering on close, hold, and trolley drum of ship unloader - PJB UP Paiton, 2013
Basic engineering of rotating mechanism of 150 m flag tower, PT. Bukit Jaya Abadi, 2014







Publications:

Indra Sidharta, Wajan Berata, Mechanical and Microstructure Characteristics of Austempered
FCD 500, presented at National Conference of Industrial Technology XIII, Sepuluh Nopember
Institute of Technology (ITS) Indonesia, March 2007

Indra Sidharta, Sulistijono, Organic Coating as Corrosion Protection of Reinforcing Steel,
Jurnal Teknik Mesin Vol. 7 No. 1, January 2007

Indra Sidharta, Wajan Berata, PENGARUH WAKTU PEMINDAHAN SELAMA PROSES
AUSTEMPERING TERHADAP STRUKTUR MIKRO DAN SIFAT MEKANIK BESI
TUANG NODULAR FCD 500, Seminar Nasional Teknik Mesin 6, May 2011

Indra Sidharta, Wajan Berata, Effect of Transfer Time During Austempering of Nodular Cast
Iron FCD 450, Jurnal Teknik Mesin Vol. 11 No. 3, September 2011

Indra Sidharta, Rahadian Firman, Asri Kusumaningtyas, Wajan Berata, H. C. Kis Agustin,
Wahyu Wijanarko, Sutikno, Short Solution Treatment of Cast Al-Si-Mg Alloy in Salt Bath
Furnace, APTECS 3, December 2011

Indra Sidharta, Sutikno, Wahyu Wijanarko, Fabrication of Ti3SiC2 by Mechanical Alloying
Under Air Atmosphere, SNTTM XI, October 2012

Subowo, Gathot Dwi Winarno, Indra Sidharta, Sutikno, Pengaruh Post Bending Heat
Treatment Terhadap Kekerasan dan Struktur Mikro Material Superheater Tube SA-335 Grade
P91, SNTTM XI, October 2012

Dwi Ika Basitha, Indra Sidharta, Soeharto, Sutikno, Putu Suwarta, ANALISA DAMPAK
OVERHEATING TERHADAP TUBE KATALIS HP-40 MODIFIKASI DI PRIMARY
REFORMER PABRIK AMMONIA, Seminar Nasional Pascasarjana ITS 2013

You might also like