This document appears to be a pressure drop calculator from Intersystems Automatic Filling Systems used to calculate pressure drops through a lance assembly. It includes fields to enter information about the customer, project, product properties, lance design parameters, and pipe run lengths. With this input data, it will calculate the fluid density, flow properties, friction losses through different components, total head loss, and inlet and outlet pressures and flows. However, for this calculation the project requirements are unknown so many of the input fields are blank.
This document appears to be a pressure drop calculator from Intersystems Automatic Filling Systems used to calculate pressure drops through a lance assembly. It includes fields to enter information about the customer, project, product properties, lance design parameters, and pipe run lengths. With this input data, it will calculate the fluid density, flow properties, friction losses through different components, total head loss, and inlet and outlet pressures and flows. However, for this calculation the project requirements are unknown so many of the input fields are blank.
This document appears to be a pressure drop calculator from Intersystems Automatic Filling Systems used to calculate pressure drops through a lance assembly. It includes fields to enter information about the customer, project, product properties, lance design parameters, and pipe run lengths. With this input data, it will calculate the fluid density, flow properties, friction losses through different components, total head loss, and inlet and outlet pressures and flows. However, for this calculation the project requirements are unknown so many of the input fields are blank.
Customer: Project: Product Tag: Product Flow: GPM Product Temperature: 75 F Viscosity@25C 1 CP Specific Gravity 1 SG Horizontal Lance Piping Size 1.61 "A" "B" "C" "D" "E" "F" Vertical Lance Piping Size 1.61 0.5 - 1.0 - 4.0 - Lance Foot Valve 1 Free Flow Design 2 Filler Type 1 Fill Mode Reference Diagram Fluid Density 61.4 LBS/FT3 Kinematic Viscosity: 1.0687E-05 ft2/sec Horizontal Inside Dia.: 0.1342 ft Vertical Inside Dia.: 0.1342 ft project requirements are unknown. Flow Area: 0.0141 ft2 Flow Quantity: cfs Velocity: fps Flow: LAMINAR Reynolds No.: Nre Relative Roughness: 0.0015 r PSI Nipple Moody Friction Factor: fa Pressure Drop: PSI Valve Head Loss "A" ft Pressure Drop: PSI Nipple Head Loss "B" ft Pressure Drop: PSI Tee Head Loss "C" ft Pressure Drop: PSI Lance/Rod Head Loss "D" ft Pressure Drop: PSI Foot Valve Head Loss "E" ft PSI System Head Loss "F" ft Total Head Loss System ft Inlet GPM: 90 Outlet GPM: Pump Flow Summary: PUMP FLOW IS ADEQUATE Inlet PSI: 30 Outlet PSI: Pump Pressure Summary: PUMP PSI IS ADEQUATE Entered by: Date: PRESSURE DROP CALCULATOR (Rev. D) Intersystems Automatic Filling Systems Do not change these values. Drop down menu will input correct data. Product Name For Assistance, scroll text box: Product Flow and Pressure Drop are based on standard product design with the above drop down menu selections as the only allowable size and feature options. If the sheet is producing other than expected results, please contact the Factory for assistance. Velcon does not assume any responsibility for Velcon lance assembly. Typical "In-Container" penetrations are 3" for Top-Fill and 31" for Data and results provided by this worksheet are intended for reference only. All calculations Calculated Data The above diagram is representative of a standard the accuracy of this worksheet. Lance Design Parameters Select Lance Design Desired Drums/Hr. Desired Gals./Hr. Actual GPM (if known) SubSurface-Fill. Please consult Factory if Enter One Value Only Enter "0" For Other Entries Customer Name Project Name TYPICAL LANCE FEATURES 9575 N 109th Ave Omaha, NE 68142 402.330.1500 www.intersystems.net Intersystems Automatic Filling Systems Enter Production Requirements In Desired Drums/Hr OR Gals/Hr Enter "0" For Other Entries Production Requirements Name Date Notes: LENGTH IN FEET above to achieve desired Drums/Hr. or Gals./Hr. Pressure Drop: Enter Lance inlet pressure and flow, if known. Output GPM displayed must be greater than Product Flow GPM shown Pressure Drop: FLOW CALCULATIONS 90 30.000 A B C
D
E F Customer: Project: Product Flow: 0 GPM Product Temperature: 0 F Viscosity@25C 0 CP Specific Gravity 0 SG Horizontal Lance Piping Size 0.87 Vertical Lance Piping Size 0.87 No. of 90 Degree Fittings 0 No. of 45 Degree Fittings 0 No. of Valves 0 Feet of Flexible Hose 0 Fluid Density 0 LBS/FT3 Kinematic Viscosity: 0.0000E+00 ft2/sec Horizontal Inside Dia.: 0.0725 ft Vertical Inside Dia.: 0.0725 ft Flow Area: 0.0041 ft2 Flow Quantity: 0.0000 cfs Velocity: 0.0000 fps Flow: Reynolds No.: Nre Relative Roughness: 0.0028 r PSI Moody Friction Factor: fa Pressure Drop: PSI Head Loss Horizontal Piping ft Pressure Drop: PSI Head Loss Vertical Piping ft Pressure Drop: PSI Head Loss 90 Degree Fittings ft Pressure Drop: PSI Head Loss 45 Degree Fittings ft Pressure Drop: PSI Head Loss Valves ft 0.000 PSI Head Loss Flexible Hose ft Total Head Loss System 0.0000 ft Inlet GPM: 0 Outlet GPM: Pump Flow Summary: ERROR Inlet PSI: 0 Outlet PSI: Product Flow and Pressure Drop TURBULENT Pressure Drop: Pressure Drop: FLOW CALCULATIONS the accuracy of this worksheet. Calculated Data allowable size and feature options. If the sheet is producing other than expected results, please contact the Factory for assistance. Velcon does not assume any responsibility for Data and results provided by this worksheet are intended for reference only. All calculations are based on standard product design with the above drop down menu selections as the only Horizontal Vertical 0.0 Lance Design Parameters LENGTH IN FEET Enter Pipe Run Lengths in Feet Select Piping Design 402.330.1500 www.intersystems.net Project Name 0.0 For Assistance, scroll text box: Intersystems Automatic Filling Systems 9575 N 109th Ave Omaha, NE 68142 PIPE PRESSURE DROP CALCULATOR Intersystems Automatic Filling Systems Customer Name Notes Pump Pressure Summary: ERROR Entered by: Date: Enter pipe inlet pressure and flow, if known. Output GPM Name displayed must be greater than Product Flow GPM shown Date above to achieve desired Flow Rate Horizontal Piping Vertical Piping 90 Degree Fittings 45 Degree Fittings Valves Flexible Hose System ERROR ERROR Product Flow and Pressure Drop FLOW CALCULATIONS Vertical LENGTH IN FEET Enter Pipe Run Lengths in Feet Project Name 0.0 For Assistance, scroll text box: PIPE PRESSURE DROP CALCULATOR Intersystems Automatic Filling Systems Customer Name Notes Enter pipe inlet pressure and flow, if known. Output GPM displayed must be greater than Product Flow GPM shown above to achieve desired Flow Rate