Indianapolis, IN 46204-1763 USA Telephone: 800-533-0341, option #1 Fax: 317-248-6534 e-mail: coatings@vertellus.com
Information contained in this publication is accurate to the best knowledge and belief of Vertellus Specialties Inc. Any information or advice obtained from Vertellus Specialties Inc. is also given in good faith and it remains at all times the responsibility of the customer to ensure that the materials are suitable for the purpose intended. Due to a policy of continued development work, and according to the availability of raw materials, products may differ in detail from those described and are offered subject to the Company's conditions of sale.
Revised: April 2006
PRODUCT DATA SHEET METROTECT ACOTHANE TU BRUSH GRADE Desc r i pt i on: High build, solvent free, two component, tar modified urethane coating with outstanding physical properties in terms of flexural strength, tensile strength, impact resistance, and hardness. Uses: Protection of steel and concrete structures in aggressive environments, i.e. internal and external protection of pipelines, offshore splash zones, chemical plants, effluent tanks, etc. Designed for application to small areas and items, or where spray application is impractical. Also suitable for repair to mechanically damaged coating and upgrading of below thickness spray applied Acothane TU. Col or : Black Vol ume Sol i ds: 100% Fl ash Poi nt : DIN 51758: Base: 150C (300F) Activator: 200C (390F) Temper at ur e: Application: Preferably above 0C (32F) ambient Service: Immersion 0C to 80C (32F to 176F) depending on solution Dry: -20C to 110C (-4F to 230F) continuous Dr yi ng Ti mes at 20C (68F): Surface: 1 2 hours Hard: 6 8 hours Recoat: Minimum 1 hour, maximum 24 hours Ul t i mat e Cur e: Approximately 14 days at 25C (77F), at lower temperatures, the curing rate will be slower Bond St r engt h: Grit blasted steel: >10 MPa at 23C (73F) (ISO 4624) Wat er Vapor Per meabi l i t y: DIN 52615 0.005 metric/perm cm Thi c k ness: Approximately 500 microns per coat. Two to three coats normally required for optimum performance. Cover age: Theoretical: 2 m/liter at 500 microns DFT Suggested Practical: 1.2 1.6 m/liter per coat, will vary depending on the
PIPELINE COATINGS GROUP 300 North Meridian Street, Suite 1500 Indianapolis, IN 46204-1763 USA Telephone: 800-533-0341, option #1 Fax: 317-248-6534 e-mail: coatings@vertellus.com
Information contained in this publication is accurate to the best knowledge and belief of Vertellus Specialties Inc. Any information or advice obtained from Vertellus Specialties Inc. is also given in good faith and it remains at all times the responsibility of the customer to ensure that the materials are suitable for the purpose intended. Due to a policy of continued development work, and according to the availability of raw materials, products may differ in detail from those described and are offered subject to the Company's conditions of sale.
Revised: April 2006
complexity of the structure being coated and nature of the substrate Pot Li f e: 15 - 25 minutes at 20C (68F) 125 g mass Shr i nk age: Negligible I mpac t : ASTM 2794-69/14: 10 NM Tensi l e St r engt h: DIN 53504: 10 13 N/mm 2 El ongat i on: ASTM D2370: 20 30% Shor e D Har dness: 65 70 approximately Fl ex i bi l i t y: British Gas PS/CW6: Pass 2% strain at 5C (41F) Cat hodi c Di sbondment : DIN 30671: 30 days at 23C (73F), thickness 1 mm - Pass DIN 30671: 2 days at 65C (149F), thickness 1 mm Pass Shel f Li f e: 12 months unopened in moderate, dry storage conditions Cl eaner s: Acothane 380 Solvent or Xylene is a recommended cleaning fluid. Under no circumstances should solvent be added to paint. Temper at ur e and RH Par amet er s Dur i ng Appl i c at i on: Normal application requires relative humidity below 80%. To avoid risk of condensation, application should be done only when the temperature of the steel surface is at least 3C (5F) higher than the dew point. Application at temperatures below 1C (33F) must be carefully monitored since the possible presence of ice on the surface (or in the pores in the case of concrete) will result in poor performance. Sur f ac e Pr epar at i on:
St eel :
Ensure surfaces are clean, dry and free from contaminants. Grit blast to BS7079 Standard Sa 2.5 to an amplitude of 50-100 microns. Overlap areas should be firm and well abraded.
Remove all laitence and other contaminants by most appropriate method, i.e. blast cleaning.
PIPELINE COATINGS GROUP 300 North Meridian Street, Suite 1500 Indianapolis, IN 46204-1763 USA Telephone: 800-533-0341, option #1 Fax: 317-248-6534 e-mail: coatings@vertellus.com
Information contained in this publication is accurate to the best knowledge and belief of Vertellus Specialties Inc. Any information or advice obtained from Vertellus Specialties Inc. is also given in good faith and it remains at all times the responsibility of the customer to ensure that the materials are suitable for the purpose intended. Due to a policy of continued development work, and according to the availability of raw materials, products may differ in detail from those described and are offered subject to the Company's conditions of sale.
Revised: April 2006
Conc r et e:
Ensure concrete is dry to protimeter reading of less than 5 on the concrete scale. Seal with U-Coat 501.. Mi x i ng: Stir base to ease structure, then add one complete unit of correct activator. Mix thoroughly, scraping the sides and bottom of the can, then decant into a clean container and further mix to ensure a uniform blend. Use before pot life expires. In cold conditions it is recommended that the material temperature is maintained at approximately 20C (68F) to assist mixing (water entrainment must be avoided). Appl i c at i on Met hod: Brush
Note: This material contains coal tar pitch products and is not designed for use on applications in direct contact with potable water or foodstuffs.