Professional Documents
Culture Documents
BCS-1
ELECTRICAL & POWER CONTROL
C
D
E
F
G
H
I
J
K
L
B
SECTION BCS
A
O
P
N
CONTENTS
BODY CONTROL SYSTEM
FOR EUROPE
FEATURES OF NEW MODEL .................. .... 6
APPLICATION NOTICE ................................. ..... 6
How to Check Vehicle Type ......................................6
BASIC INSPECTION ................................ .... 7
INSPECTION AND ADJUSTMENT ................ ..... 7
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT (BCM) ...............................................7
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT (BCM) : Description ................. ......7
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT (BCM) : Special Repair Require-
ment ..........................................................................7
CONFIGURATION (BCM) ...........................................7
CONFIGURATION (BCM) : Description ....................7
CONFIGURATION (BCM) : Special Repair Re-
quirement ............................................................ ......8
CONFIGURATION (BCM) : Configuration list ..... ......9
FUNCTION DIAGNOSIS ........................... ...11
BODY CONTROL SYSTEM ........................... ....11
System Description ............................................. .... 11
Component Parts Location ...................................... 12
COMBINATION SWITCH READING SYSTEM
....13
System Diagram ...................................................... 13
System Description ............................................. .... 13
SIGNAL BUFFER SYSTEM ........................... ....17
System Diagram ...................................................... 17
System Description ............................................. .... 17
POWER CONSUMPTION CONTROL SYS-
TEM ....................................................................18
System Diagram ...................................................... 18
System Description ..................................................18
Component Parts Location ......................................20
DIAGNOSIS SYSTEM (BCM) ...........................21
COMMON ITEM .........................................................21
COMMON ITEM : CONSULT-III Function (BCM -
COMMON ITEM) .....................................................21
DOOR LOCK ..............................................................22
DOOR LOCK : CONSULT-III Function (BCM -
DOOR LOCK) ..........................................................22
REAR WINDOW DEFOGGER ............................... ....23
REAR WINDOW DEFOGGER : CONSULT-III
Function (BCM - REAR DEFOGGER) .....................23
BUZZER .....................................................................24
BUZZER : CONSULT-III Function (BCM - BUZZ-
ER) ..........................................................................24
INT LAMP ............................................................... ....24
INT LAMP : CONSULT-III Function (BCM - INT
LAMP) ......................................................................25
HEADLAMP ...............................................................26
HEADLAMP : CONSULT-III Function (BCM -
HEAD LAMP) ...........................................................26
WIPER .................................................................... ....28
WIPER : CONSULT-III Function (BCM - WIPER) ....28
FLASHER ...................................................................29
FLASHER : CONSULT-III Function (BCM -
FLASHER) ........................................................... ....29
INTELLIGENT KEY ....................................................30
INTELLIGENT KEY : CONSULT-III Function
(BCM - INTELLIGENT KEY) ....................................30
COMB SW ..................................................................33
COMB SW : CONSULT-III Function (BCM -
COMB SW) ..............................................................33
BCS-2
BCM ........................................................................... 34
BCM : CONSULT-III Function (BCM - BCM) .......... 34
IMMU ......................................................................... 34
IMMU : CONSULT-III Function (BCM - IMMU) .... ... 34
BATTERY SAVER ................................................. ... 35
BATTERY SAVER : CONSULT-III Function (BCM
- BATTERY SAVER) .............................................. 35
TRUNK ...................................................................... 36
TRUNK : CONSULT-III Function (BCM - TRUNK) ... 36
THEFT ALM .............................................................. 36
THEFT ALM : CONSULT-III Function (BCM -
THEFT) ................................................................... 37
SIGNAL BUFFER ...................................................... 38
SIGNAL BUFFER : CONSULT-III Function (BCM
- SIGNAL BUFFER) ................................................ 38
COMPONENT DIAGNOSIS ..................... ... 39
U1000 CAN COMM ............................................ 39
Description .............................................................. 39
DTC Logic ............................................................... 39
Diagnosis Procedure .............................................. 39
U1010 CONTROL UNIT (CAN) ...................... ... 40
DTC Logic ............................................................... 40
Diagnosis Procedure .............................................. 40
U0415 VEHICLE SPEED SIG ............................ 41
Description .............................................................. 41
DTC Logic ............................................................... 41
Diagnosis Procedure .............................................. 41
B2562 LOW VOLTAGE .................................. ... 42
DTC Logic ............................................................... 42
Diagnosis Procedure .............................................. 42
POWER SUPPLY AND GROUND CIRCUIT ..... 43
Diagnosis Procedure .............................................. 43
COMBINATION SWITCH INPUT CIRCUIT .... ... 44
Diagnosis Procedure .............................................. 44
COMBINATION SWITCH OUTPUT CIRCUIT ... 46
Diagnosis Procedure .............................................. 46
ECU DIAGNOSIS ..................................... ... 48
BCM (BODY CONTROL MODULE) .................. 48
Reference Value ..................................................... 48
Wiring Diagram - BCM (LHD models) - .................. 73
Wiring Diagram - BCM (RHD models) - .................. 79
Fail-safe ............................................................... ... 85
DTC Inspection Priority Chart .............................. 88
DTC Index .............................................................. 89
SYMPTOM DIAGNOSIS .......................... ... 92
COMBINATION SWITCH SYSTEM SYMP-
TOMS .............................................................. ... 92
Symptom Table ....................................................... 92
PRECAUTION ............................................ 93
PRECAUTIONS ................................................. 93
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ................................................................. 93
Precaution for Battery Service ................................ 93
ON-VEHICLE REPAIR ............................... 94
BCM (BODY CONTROL MODULE) .................. 94
Exploded View ........................................................ 94
Removal and Installation ......................................... 94
COMBINATION SWITCH ............................... ... 95
Exploded View ........................................................ 95
Removal and Installation ......................................... 95
FOR GENERAL AREAS
FEATURES OF NEW MODEL ................... 96
APPLICATION NOTICE ................................. ... 96
How to Check Vehicle Type .................................... 96
BASIC INSPECTION .................................. 97
INSPECTION AND ADJUSTMENT ................... 97
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT (BCM) ............................................ 97
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT (BCM) : Description ..................... 97
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT (BCM) : Special Repair Require-
ment ..................................................................... ... 97
CONFIGURATION (BCM) ......................................... 97
CONFIGURATION (BCM) : Description ................. 97
CONFIGURATION (BCM) : Special Repair Re-
quirement ................................................................ 98
CONFIGURATION (BCM) : Configuration list ...... ... 99
FUNCTION DIAGNOSIS ........................... 103
BODY CONTROL SYSTEM ........................... ..103
System Description ............................................... 103
Component Parts Location ................................... 104
COMBINATION SWITCH READING SYSTEM
..105
System Diagram ................................................... 105
System Description ............................................... 105
SIGNAL BUFFER SYSTEM ........................... ..109
System Diagram ................................................... 109
System Description ............................................... 109
BCS
BCS-3
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
POWER CONSUMPTION CONTROL SYS-
TEM .................................................................. 110
System Diagram .................................................... 110
System Description ............................................. .. 110
Component Parts Location .................................... 112
DIAGNOSIS SYSTEM (BCM) ........................ .. 113
COMMON ITEM ....................................................... 113
COMMON ITEM : CONSULT-III Function (BCM -
COMMON ITEM) ................................................. .. 113
DOOR LOCK ........................................................... 114
DOOR LOCK : CONSULT-III Function (BCM -
DOOR LOCK) ....................................................... 114
REAR WINDOW DEFOGGER ................................. 115
REAR WINDOW DEFOGGER : CONSULT-III
Function (BCM - REAR DEFOGGER) .................. 116
BUZZER ................................................................... 116
BUZZER : CONSULT-III Function (BCM - BUZZ-
ER) ........................................................................ 116
INT LAMP ................................................................ 117
INT LAMP : CONSULT-III Function (BCM - INT
LAMP) ................................................................... 117
HEADLAMP ............................................................. 119
HEADLAMP : CONSULT-III Function (BCM -
HEAD LAMP) ........................................................ 119
WIPER ..................................................................... 120
WIPER : CONSULT-III Function (BCM - WIPER) .. 120
FLASHER ................................................................ 122
FLASHER : CONSULT-III Function (BCM -
FLASHER) ............................................................ 122
INTELLIGENT KEY ................................................. 122
INTELLIGENT KEY : CONSULT-III Function
(BCM - INTELLIGENT KEY) ................................. 122
COMB SW ............................................................... 126
COMB SW : CONSULT-III Function (BCM -
COMB SW) ........................................................... 126
BCM ......................................................................... 126
BCM : CONSULT-III Function (BCM - BCM) ........ 127
IMMU ........................................................................ 127
IMMU : CONSULT-III Function (BCM - IMMU) ..... 127
BATTERY SAVER ................................................... 127
BATTERY SAVER : CONSULT-III Function (BCM
- BATTERY SAVER) ............................................. 127
TRUNK ................................................................... .. 128
TRUNK : CONSULT-III Function (BCM - TRUNK) .. 128
THEFT ALM ........................................................... .. 129
THEFT ALM : CONSULT-III Function (BCM -
THEFT) ................................................................. 129
RETAINED PWR ......................................................130
RETAINED PWR : CONSULT-III Function (BCM -
RETAINED PWR) ..................................................130
SIGNAL BUFFER ....................................................130
SIGNAL BUFFER : CONSULT-III Function (BCM
- SIGNAL BUFFER) ...............................................130
AIR PRESSURE MONITOR .....................................131
AIR PRESSURE MONITOR : Diagnosis Descrip-
tion ....................................................................... ..131
AIR PRESSURE MONITOR : CONSULT-III Func-
tion ....................................................................... ..132
COMPONENT DIAGNOSIS ...................... . 134
U1000 CAN COMM ......................................... 134
Description .............................................................134
DTC Logic ............................................................ ..134
Diagnosis Procedure .............................................134
U1010 CONTROL UNIT (CAN) ....................... 135
DTC Logic ............................................................ ..135
Diagnosis Procedure .............................................135
U0415 VEHICLE SPEED SIG ......................... 136
Description .............................................................136
DTC Logic ............................................................ ..136
Diagnosis Procedure .............................................136
B2562 LOW VOLTAGE .................................. 137
DTC Logic ............................................................ ..137
Diagnosis Procedure .............................................137
POWER SUPPLY AND GROUND CIRCUIT .. 138
Diagnosis Procedure .............................................138
COMBINATION SWITCH INPUT CIRCUIT .... 139
Diagnosis Procedure .............................................139
COMBINATION SWITCH OUTPUT CIRCUIT . 141
Diagnosis Procedure .............................................141
ECU DIAGNOSIS ...................................... . 143
BCM (BODY CONTROL MODULE) ............... 143
Reference Value .................................................. ..143
Wiring Diagram - BCM (LHD models) - .................167
Wiring Diagram - BCM (RHD models) - .................173
Fail-safe ............................................................... ..178
DTC Inspection Priority Chart ........................... ..181
DTC Index .............................................................182
SYMPTOM DIAGNOSIS ........................... . 185
COMBINATION SWITCH SYSTEM SYMP-
TOMS .............................................................. 185
Symptom Table .....................................................185
PRECAUTION ........................................... . 186
PRECAUTIONS ............................................... 186
BCS-4
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ................................................................186
Precaution for Battery Service ...............................186
ON-VEHICLE REPAIR ............................. ..187
BCM (BODY CONTROL MODULE) ................ 187
Exploded View .......................................................187
Removal and Installation .......................................187
COMBINATION SWITCH ................................ 188
Exploded View .......................................................188
Removal and Installation .......................................188
FOR SOUTH AFRICA
FEATURES OF NEW MODEL ................. ..189
APPLICATION NOTICE ................................. . 189
How to Check Vehicle Type ................................ ..189
BASIC INSPECTION ................................ ..190
INSPECTION AND ADJUSTMENT ................. 190
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT (BCM) ...........................................190
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT (BCM) : Description ................. ..190
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT (BCM) : Special Repair Require-
ment .......................................................................190
CONFIGURATION (BCM) ........................................190
CONFIGURATION (BCM) : Description ................190
CONFIGURATION (BCM) : Special Repair Re-
quirement ...............................................................191
CONFIGURATION (BCM) : Configuration list .......192
FUNCTION DIAGNOSIS .......................... ..193
BODY CONTROL SYSTEM ............................ 193
System Description .............................................. ..193
Component Parts Location .................................. ..194
COMBINATION SWITCH READING SYSTEM
. 195
System Diagram ....................................................195
System Description .............................................. ..195
SIGNAL BUFFER SYSTEM ............................ 199
System Diagram ....................................................199
System Description .............................................. ..199
POWER CONSUMPTION CONTROL SYS-
TEM ................................................................. . 200
System Diagram ....................................................200
System Description .............................................. ..200
Component Parts Location .................................. ..202
DIAGNOSIS SYSTEM (BCM) .......................... 203
COMMON ITEM ....................................................... 203
COMMON ITEM : CONSULT-III Function (BCM -
COMMON ITEM) .................................................. 203
DOOR LOCK ........................................................... 204
DOOR LOCK : CONSULT-III Function (BCM -
DOOR LOCK) ....................................................... 204
REAR WINDOW DEFOGGER ................................ 205
REAR WINDOW DEFOGGER : CONSULT-III
Function (BCM - REAR DEFOGGER) .................. 205
BUZZER .................................................................. 206
BUZZER : CONSULT-III Function (BCM - BUZZ-
ER) ........................................................................ 206
INT LAMP ................................................................ 206
INT LAMP : CONSULT-III Function (BCM - INT
LAMP) ................................................................... 207
HEADLAMP ............................................................ . 208
HEADLAMP : CONSULT-III Function (BCM -
HEAD LAMP) ........................................................ 208
WIPER ..................................................................... 210
WIPER : CONSULT-III Function (BCM - WIPER) . 210
FLASHER ................................................................ 211
FLASHER : CONSULT-III Function (BCM -
FLASHER) ............................................................ 211
INTELLIGENT KEY ................................................. 212
INTELLIGENT KEY : CONSULT-III Function
(BCM - INTELLIGENT KEY) ................................. 212
COMB SW ............................................................... 215
COMB SW : CONSULT-III Function (BCM -
COMB SW) ........................................................... 215
BCM ......................................................................... 216
BCM : CONSULT-III Function (BCM - BCM) ........ 216
IMMU ....................................................................... 216
IMMU : CONSULT-III Function (BCM - IMMU) ..... 216
BATTERY SAVER .................................................. . 217
BATTERY SAVER : CONSULT-III Function (BCM
- BATTERY SAVER) ............................................. 217
TRUNK .................................................................... 218
TRUNK : CONSULT-III Function (BCM - TRUNK) . 218
THEFT ALM ............................................................. 218
THEFT ALM : CONSULT-III Function (BCM -
THEFT) ................................................................. 219
SIGNAL BUFFER ................................................... . 220
SIGNAL BUFFER : CONSULT-III Function (BCM
- SIGNAL BUFFER) .............................................. 220
COMPONENT DIAGNOSIS ...................... 221
U1000 CAN COMM ..........................................221
Description ............................................................ 221
BCS
BCS-5
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
DTC Logic ............................................................. 221
Diagnosis Procedure ............................................. 221
U1010 CONTROL UNIT (CAN) ...................... .. 222
DTC Logic ............................................................. 222
Diagnosis Procedure ............................................. 222
U0415 VEHICLE SPEED SIG ........................ .. 223
Description ............................................................ 223
DTC Logic ............................................................. 223
Diagnosis Procedure ............................................. 223
B2562 LOW VOLTAGE .................................. .. 224
DTC Logic ............................................................. 224
Diagnosis Procedure ............................................. 224
POWER SUPPLY AND GROUND CIRCUIT .... 225
Diagnosis Procedure ............................................. 225
COMBINATION SWITCH INPUT CIRCUIT .... .. 226
Diagnosis Procedure ............................................. 226
COMBINATION SWITCH OUTPUT CIRCUIT .. 228
Diagnosis Procedure ............................................. 228
ECU DIAGNOSIS ....................................... 230
BCM (BODY CONTROL MODULE) ................. 230
Reference Value ................................................. .. 230
Wiring Diagram - BCM - ........................................253
Fail-safe ............................................................... ..258
DTC Inspection Priority Chart ........................... ..261
DTC Index .............................................................262
SYMPTOM DIAGNOSIS ........................... . 264
COMBINATION SWITCH SYSTEM SYMP-
TOMS .............................................................. 264
Symptom Table .....................................................264
PRECAUTION ........................................... . 265
PRECAUTIONS ............................................... 265
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ...............................................................265
Precaution for Battery Service ............................. ..265
ON-VEHICLE REPAIR .............................. . 266
BCM (BODY CONTROL MODULE) ............... 266
Exploded View .......................................................266
Removal and Installation ..................................... ..266
COMBINATION SWITCH ................................ 267
Exploded View .......................................................267
Removal and Installation ..................................... ..267
BCS-6
< FEATURES OF NEW MODEL >
[FOR EUROPE]
APPLICATION NOTICE
FEATURES OF NEW MODEL
APPLICATION NOTICE
How to Check Vehicle Type INFOID:0000000005000990
Check the vehicle type (refer to GI-21, "Model Variation") to use the service information in this section.
Application Service information
Europe (RH drive, LH drive)
FOR EUROPE
Russia and Ukraine
Australia, New Zealand and General areas (RH drive)
FOR GENERAL AREAS
Hong Kong, Singapore and Brunei
Middle East
General areas (LH drive)
South Africa FOR SOUTH AFRICA
BCS
INSPECTION AND ADJUSTMENT
BCS-7
< BASIC INSPECTION >
[FOR EUROPE]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
BASIC INSPECTION
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM)
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM) : Description
INFOID:0000000005000991
BEFORE REPLACEMENT
When replacing BCM, save or print current vehicle specification with CONSULT-III configuration before
replacement.
NOTE:
If READ CONFIGURATION can not be used, use the WRITE CONFIGURATION - Manual selection after
replacing BCM.
AFTER REPLACEMENT
CAUTION:
When replacing BCM, you must perform WRITE CONFIGURATION with CONSULT-III.
- Complete the procedure of WRITE CONFIGURATION in order.
- If you set incorrect WRITE CONFIGURATION, incidents might occur.
- Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
When replacing BCM, perform the system initialization (NATS).
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM) : Special Repair
Requirement INFOID:0000000005000992
1.SAVING VEHICLE SPECIFICATION
CONSULT-III Configuration
Perform READ CONFIGURATION to save or print current vehicle specification. Refer to BCS-7, "CONFIGU-
RATION (BCM) : Description".
NOTE:
If READ CONFIGURATION can not be used, use the WRITE CONFIGURATION - Manual selection after
replacing BCM.
>> GO TO 2.
2.REPLACE BCM
Replace BCM. Refer to BCS-94, "Exploded View".
>> GO TO 3.
3.WRITING VEHICLE SPECIFICATION
CONSULT-III Configuration
Perform WRITE CONFIGURATION - Config file or WRITE CONFIGURATION - Manual selection to write
vehicle specification. Refer to BCS-8, "CONFIGURATION (BCM) : Special Repair Requirement".
>> GO TO 4.
4.INITIALIZE BCM (NATS)
Perform BCM initialization. (NATS)
>> WORK END
CONFIGURATION (BCM)
CONFIGURATION (BCM) : Description INFOID:0000000005000993
Vehicle specification needs to be written with CONSULT-III because it is not written after replacing BCM.
BCS-8
< BASIC INSPECTION >
[FOR EUROPE]
INSPECTION AND ADJUSTMENT
Configuration has three functions as follows
NOTE:
Manual setting item: Items which need selection by vehicle specifications
Automatic setting item: Items which are written in automatically (Setting can not be changed)
CAUTION:
When replacing BCM, you must perform WRITE CONFIGURATION with CONSULT-III.
Complete the procedure of WRITE CONFIGURATION in order.
If you set incorrect WRITE CONFIGURATION, incidents might occur.
Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
Never perform WRITE CONFIGURATION except for new BCM.
CONFIGURATION (BCM) : Special Repair Requirement INFOID:0000000005000994
1.WRITING MODE SELECTION
CONSULT-III Configuration
Select CONFIGURATION of BCM.
When writing saved data>>GO TO 2.
When writing manually>>GO TO 3.
2.PERFORM WRITE CONFIGURATION - CONFIG FILE
CONSULT-III Configuration
Perform WRITE CONFIGURATION - Config file.
>> WORK END
3.PERFORM WRITE CONFIGURATION - MANUAL SELECTION
CONSULT-III Configuration
1. Select "WRITE CONFIGURATION - Manual selection".
2. Identify the correct model and configuration list. Refer to BCS-9, "CONFIGURATION (BCM) : Configura-
tion list".
3. Confirm and/or change setting value for each item.
CAUTION:
Thoroughly read and understand the vehicle specification. Incorrect settings may result in abnor-
mal control of ECU.
4. Select "SETTING".
CAUTION:
Make sure to select SETTING even if the indicated configuration of brand new BCM is same as
the desirable configuration. If not, configuration which is set automatically by selecting vehicle
model can not be memorized.
5. When "COMMAND FINISHED", select "END".
>> GO TO 4.
4.OPERATION CHECK
Confirm that each function controlled by BCM operates normally.
>> WORK END
Function Description
READ CONFIGURATION
Reads the vehicle configuration of current BCM.
Saves the read vehicle configuration.
WRITE CONFIGURATION - Manual selection Writes the vehicle configuration with manual selection.
WRITE CONFIGURATION - Config file Writes the vehicle configuration with saved data.
BCS
INSPECTION AND ADJUSTMENT
BCS-9
< BASIC INSPECTION >
[FOR EUROPE]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
CONFIGURATION (BCM) : Configuration list INFOID:0000000005000995
CAUTION:
Thoroughly read and understand the vehicle specification. Incorrect settings may result in abnormal
control of ECU.
EXCEPT FOR U.K.
: Items which confirm vehicle specifications
FOR U.K.
MANUAL SETTING ITEM
NOTE
Items Setting value
AV C/U WITH WITHOUT
HANDLE RHD LHD
DTRL WITH WITHOUT
TRANSMISSION AT with ABS MT with ABS
THEFT ALM AREA WITHOUT MODE4
WITHOUT: Without vehicle security system
MODE4: With vehicle security system
LIGHT&RAIN SEN TYPE MODE1 MODE3
MODE1: With light & rain sensor
MODE3: With rain sensor
THFT ALM TYPE MODE1 MODE2
MODE1: Without siren control unit
MODE2: With siren control unit
ASCD CANCEL SW TYPE MODE1 MODE2
MODE1: M/T with ASCD and SynchroRev Match mode
models
MODE2: Except M/T with ASCD and SynchroRev Match
mode models
AUTO SETTING ITEM
NOTE
Items Setting value
SUPER LOCK WITHOUT
P/W UP/DOWN WITHOUT
ROOF FUNCTION W/O REQ SW
AUTO BACK DOOR WITHOUT
Trunk/Glass Hatch select Glass Hatch
Glass Hatch is indicated also for vehicles without a glass
hatch.
TR OPEN SW (INT) MODE1
H/L BAT SAVER SET WITH
LIGHT RECOG MODE4
REAR WIPER WITH WITH is indicated also for vehicles without a rear wiper.
H/L WASHER MODE3
HAZARD SW TYPE MODE1
BCM AC CONTROL MODE1
DONGLE WITHOUT
AUTO LOCK&UNLOCK FUNC WITHOUT
AUTO DOOR LOCK SELECT WITHOUT
AUTO DOOR UNLOCK SELECT WITHOUT
H/L BAT SAVER FUNC WITH
RAIN SENSOR TYPE MODE6
Key Fob Type MODE6
DROP WIP FUNCTION WITH
BCS-10
< BASIC INSPECTION >
[FOR EUROPE]
INSPECTION AND ADJUSTMENT
: Items which confirm vehicle specifications
MANUAL SETTING ITEM
NOTE
Items Setting value
AV C/U WITH WITHOUT
TRANSMISSION AT with ABS MT with ABS
ASCD CANCEL SW TYPE MODE1 MODE2
MODE1: M/T with ASCD and SynchroRev Match mode
models
MODE2: Except M/T with ASCD and SynchroRev Match
mode models
AUTO SETTING ITEM
NOTE
Items Setting value
SUPER LOCK WITH
P/W UP/DOWN WITHOUT
ROOF FUNCTION W/O REQ SW
AUTO BACK DOOR WITHOUT
Trunk/Glass Hatch select Glass Hatch
TR OPEN SW (INT) MODE1
H/L BAT SAVER SET WITH
HANDLE RHD
DTRL WITHOUT
LIGHT RECOG MODE4
REAR WIPER WITH
THEFT ALM AREA MODE4
H/L WASHER MODE3
HAZARD SW TYPE MODE1
LIGHT&RAIN SEN TYPE MODE1
BCM AC CONTROL MODE1
THFT ALM TYPE MODE2
DONGLE WITH
AUTO LOCK&UNLOCK FUNC WITHOUT
AUTO DOOR LOCK SELECT WITHOUT
AUTO DOOR UNLOCK SELECT WITHOUT
H/L BAT SAVER FUNC WITH
RAIN SENSOR TYPE MODE6
Key Fob Type MODE6
DROP WIP FUNCTION WITH
BCS
BODY CONTROL SYSTEM
BCS-11
< FUNCTION DIAGNOSIS >
[FOR EUROPE]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
FUNCTION DIAGNOSIS
BODY CONTROL SYSTEM
System Description INFOID:0000000005000841
OUTLINE
BCM (Body Control Module) controls the various electrical components. It inputs the information required to
the control from CAN communication and the signal received from each switch and sensor.
BCM has combination switch reading function for reading the operation status of combination switches (light,
turn signal, wiper and washer) in addition to a function for controlling the operation of various electrical com-
ponents. It also has the signal transmission function as the passed point of signal and the power saving con-
trol function that reduces the power consumption with the ignition switch OFF.
BCM is equipped with the diagnosis function that performs the diagnosis with CONSULT-III and various set-
tings.
BCM control function list
System Refer to
Combination switch reading system BCS-13, "System Diagram"
Signal buffer system BCS-17, "System Diagram"
Power consumption control system BCS-18, "System Diagram"
Auto light system
EXL-21, "WITH LIGHT & RAIN SENSOR : System Diagram"
(With light & rain sensor)
EXL-23, "WITH OPTICAL SENSOR : System Diagram" (With
optical sensor)
Turn signal and hazard warning lamp system EXL-27, "System Diagram"
Headlamp system EXL-16, "System Diagram"
Parking, license plate and tail lamps system
EXL-29, "WITHOUT DAYTIME RUNNING LIGHT SYSTEM :
System Diagram" (Without daytime running light system)
EXL-31, "WITH DAYTIME RUNNING LIGHT SYSTEM : Sys-
tem Diagram" (With daytime running light system)
Rear fog lamp system EXL-33, "System Diagram"
Exterior lamp battery saver system EXL-35, "System Diagram"
Daytime running light system EXL-19, "System Diagram"
Interior room lamp control system
INL-5, "System Diagram"
Luggage room lamp system
Interior room lamp battery saver system INL-8, "System Diagram"
Front wiper and washer system WW-10, "System Diagram"
Rear wiper and washer system WW-14, "System Diagram"
Headlamp washer system WW-18, "System Diagram"
Warning chime system WCS-7, "WARNING CHIME SYSTEM : System Diagram"
Door lock system
DLK-20, "System Diagram" (With super lock)
DLK-254, "System Diagram" (Without super lock)
Back door opener system
DLK-56, "System Diagram" (With super lock)
DLK-286, "System Diagram" (Without super lock)
Nissan Vehicle Immobilizer System (NVIS) - NATS SEC-18, "System Diagram"
Vehicle security system SEC-24, "FOR EUROPE : System Diagram"
Rear window defogger system
DEF-6, "WITH NAVIGATION : System Diagram" (With NAVI)
DEF-8, "WITHOUT NAVIGATION : System Diagram" (Without
NAVI)
BCS-12
< FUNCTION DIAGNOSIS >
[FOR EUROPE]
BODY CONTROL SYSTEM
Component Parts Location INFOID:0000000005000842
Intelligent Key system/engine start system
Door lock function
DLK-23, "INTELLIGENT KEY SYSTEM : System Diagram"
(With super lock)
DLK-256, "INTELLIGENT KEY SYSTEM : System Diagram"
(Without super lock)
Super lock function
Back door open func-
tion
Remote keyless entry
function
Key reminder function
Warning function
Engine start function
Power window system PWC-10, "System Diagram"
System Refer to
1. BCM
A. Dash side lower (passenger side)
JPMIA1345ZZ
BCS
COMBINATION SWITCH READING SYSTEM
BCS-13
< FUNCTION DIAGNOSIS >
[FOR EUROPE]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
COMBINATION SWITCH READING SYSTEM
System Diagram INFOID:0000000005000843
System Description INFOID:0000000005000844
OUTLINE
BCM reads the status of the combination switch (light, turn signal, wiper and washer) and recognizes the
status of each switch.
BCM is a combination of 5 output terminals (OUTPUT 1 - 5) and 5 input terminals (INPUT 1 - 5). It reads a
maximum of 20 switch status.
COMBINATION SWITCH MATRIX
Combination switch circuit
Combination switch INPUT-OUTPUT system list
JPMIA1490GB
System OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5
INPUT 1 FR WASHER FR WIPER LOW TURN LH TURN RH
INPUT 2 FR WIPER HI FR WIPER AUTO PASSING HEADLAMP 1
INPUT 3 WIP VOLUME 1 RR WASHER HEADLAMP 2 HI BEAM
JPMIA1491GB
BCS-14
< FUNCTION DIAGNOSIS >
[FOR EUROPE]
COMBINATION SWITCH READING SYSTEM
NOTE:
Headlamp has a dual system switch.
COMBINATION SWITCH READING FUNCTION
Description
BCM reads the status of the combination switch at 10 ms interval normally.
NOTE:
BCM reads the status of the combination switch at 60 ms interval when BCM is controlled at low power con-
sumption mode.
BCM operates as follows and judges the status of the combination switch.
- INPUT 1 - 5 outputs the voltage waveforms of 5 systems simultaneously.
- It operates the transistor on OUTPUT side in the following order: OUTPUT 5 4 3 2 1.
- The voltage waveform of INPUT corresponding to the formed circuit changes according to the operation of
the transistor on OUTPUT side if any (1 or more) switches are ON.
- It reads this change of the voltage as the status signal of the combination switch.
Operation Example
In the following operation example, the combination of the status signals of the combination switch is replaced
as follows: INPUT 1 - 5 to 1 - 5 and OUTPUT 1 - 5 to A - E.
Example 1: When a switch (TURN RH switch) is turned ON
INPUT 4 RR WIPER INT WIP VOLUME 3 AUTO LIGHT TAIL LAMP
INPUT 5 WIP VOLUME 2 RR WIPER ON RR FOG
System OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5
JPMIA0067GB
JPMIA0068GB
BCS
COMBINATION SWITCH READING SYSTEM
BCS-15
< FUNCTION DIAGNOSIS >
[FOR EUROPE]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
The circuit between INPUT 1 and OUTPUT 5 is formed when the TURN RH switch is turned ON.
BCM detects the combination switch status signal 1E when the signal of OUTPUT 5 is input to INPUT 1.
BCM judges that the TURN RH switch is ON when the signal 1E is detected.
Example 2: When some switches (turn RH switch, front wiper LO switch) are turned ON
The circuits between INPUT 1 and OUTPUT 5 and between INPUT 1 and OUTPUT 3 are formed when the
TURN RH switch and FR WIPER LOW switch are turned ON.
BCM detects the combination switch status signal 1CE when the signals of OUTPUT 3 and OUTPUT 5 are
input to INPUT 1.
BCM judges that the TURN RH switch and FR WIPER LOW switch are ON when the signal 1CE is
detected.
WIPER VOLUME DIAL POSITION
BCM judges the wiper volume dial 1 - 7 by the status of WIP VOLUME 1, 2 and 3 switches.
JPMIA1492GB
JPMIA1493GB
Wiper volume dial position
Switch status
WIP VOLUME 1 WIP VOLUME 2 WIP VOLUME 3
1 ON ON ON
2 ON ON OFF
3 ON OFF OFF
4 OFF OFF OFF
5 OFF OFF ON
BCS-16
< FUNCTION DIAGNOSIS >
[FOR EUROPE]
COMBINATION SWITCH READING SYSTEM
NOTE:
For details of wiper volume dial position, refer to WW-10, "System Diagram".
6 OFF ON ON
7 OFF ON OFF
Wiper volume dial position
Switch status
WIP VOLUME 1 WIP VOLUME 2 WIP VOLUME 3
BCS
SIGNAL BUFFER SYSTEM
BCS-17
< FUNCTION DIAGNOSIS >
[FOR EUROPE]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
SIGNAL BUFFER SYSTEM
System Diagram INFOID:0000000005047921
System Description INFOID:0000000005047922
OUTLINE
BCM has the signal transmission function that outputs/transmits each input/received signal to each unit.
Signal transmission function list
JPMIA1014GB
Signal name Input Output Description
Ignition switch ON signal
Push-button ignition switch
(Push switch)
IPDM E/R (CAN)
Inputs the push-button ignition
switch (push switch) signal and
transmits the ignition switch sta-
tus judged with BCM via CAN
communication.
Door switch signal Any door switch
Combination meter (CAN)
IPDM E/R (CAN)
Inputs the door switch signal
and transmits it via CAN com-
munication.
Oil pressure switch signal IPDM E/R (CAN) Combination meter (CAN)
Transmits the received oil pres-
sure switch signal via CAN
communication.
Stop lamp switch signal Stop lamp switch TCM (CAN)
Inputs the stop lamp switch 1
signal and stop lamp switch 2
signal, and transmits the stop
lamp switch signal via CAN
communication.
BCS-18
< FUNCTION DIAGNOSIS >
[FOR EUROPE]
POWER CONSUMPTION CONTROL SYSTEM
POWER CONSUMPTION CONTROL SYSTEM
System Diagram INFOID:0000000005000848
System Description INFOID:0000000005000849
OUTLINE
BCM incorporates a power saving control function that reduces the power consumption according to the
vehicle status.
BCM switches the status (control mode) by itself with the power saving control function. It performs the sleep
request to each unit (IPDM E/R and combination meter) that operates with the ignition switch OFF.
Normal mode (wake-up)
- CAN communication is normally performed with other units
- Each control with BCM is operating properly
CAN communication sleep mode (CAN sleep)
- CAN transmission is stopped
- Control with BCM only is operating
Low power consumption mode (BCM sleep)
- Low power consumption control is active
- CAN transmission is stopped
LOW POWER CONSUMPTION CONTROL WITH BCM
BCM reduces the power consumption with the following operation in the low power consumption mode.
The reading interval of the each switches changes from 10 ms interval to 60 ms interval.
Sleep mode activation
BCM receives the sleep-ready signal (ready) from IPDM E/R and combination meter via CAN communica-
tion.
BCM transmits the sleep wake up signal (sleep) to each unit when all of the CAN sleep conditions are ful-
filled.
Each unit stops the transmission of CAN communication with the sleep wake up signal. BCM is in CAN com-
munication sleep mode.
BCM is in the low power consumption mode and perform the low power consumption control when all of the
BCM sleep conditions are fulfilled with CAN sleep condition.
JSMIA0050GB
BCS
POWER CONSUMPTION CONTROL SYSTEM
BCS-19
< FUNCTION DIAGNOSIS >
[FOR EUROPE]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
Sleep condition
Wake-up operation
BCM changes from the low power consumption mode to the CAN communication sleep mode when the any
of the BCM wake-up conditions is fulfilled. Only the control with BCM is activated.
BCM transmits the sleep wake up signal (wake up) to each unit when any of the CAN wake-up conditions is
fulfilled. It changes from the low power consumption mode or the CAN communication sleep mode to the
normal mode.
Each unit starts the transmission of CAN communication with the sleep wake up signal. In addition, the com-
bination meter transmits the wake up signal to BCM via CAN communication to report the CAN communica-
tion start.
Wake-up condition
CAN sleep condition BCM sleep condition
Receiving the sleep-ready signal (ready) from all units
Ignition switch: OFF
Vehicle security system: Not operation
Warning chime: Not operation
Intelligent Key system buzzer: Not operation
Stop lamp switch: OFF
Key slot (card switch) status: No change
Turn signal indicator lamp: Not operation
Exterior lamp: OFF
Door lock status: No change
CONSULT-III communication status: Not communication
Meter display signal: Non-transmission
Door switch status: No change
Rear window defogger: OFF
Sensor cancel switch status: No change
Interior room lamp battery saver: Time out
Power window switch communication: No transmission
Push-button ignition switch illumination: OFF
Nissan Vehicle Immobilizer System (NVIS) - NATS: Not opera-
tion
Remote keyless entry receiver communication status: No com-
munication
LOCK indicator lamp: OFF
ACC indicator lamp: OFF
ON indicator lamp: OFF
Door lock status indicator lamp: OFF
BCM wake-up condition CAN wake-up condition
Power window switch communication: Receiving
Remote keyless entry receiver: Receiving
Driver side door lock assembly (Unlock sensor):
OFF ON, ON OFF
Sensor cancel switch: OFF ON
Receiving the sleep-ready signal (Not-ready) from any units
Key slot (key switch): OFF ON, ON OFF
Push-button ignition switch (push switch): OFF ON
Hazard switch: OFF ON
HI BEAM switch: OFF ON, ON OFF
HEADLAMP 1 switch: OFF ON, ON OFF
HEADLAMP 2 switch: OFF ON, ON OFF
PASSING switch: OFF ON, ON OFF
TAIL LAMP switch: OFF ON
RR FOG switch: OFF ON
Driver door switch: OFF ON, ON OFF
Passenger door switch: OFF ON, ON OFF
Back door switch: OFF ON, ON OFF
Driver door request switch: OFF ON
Passenger door request switch: OFF ON
Back door request switch: OFF ON
Stop lamp switch: ON
Clutch interlock switch: OFF ON
BCS-20
< FUNCTION DIAGNOSIS >
[FOR EUROPE]
POWER CONSUMPTION CONTROL SYSTEM
Component Parts Location INFOID:0000000005047923
1. Combination meter 2. BCM
Refer to BCS-12, "Component Parts
Location".
3. IPDM E/R
Refer to PCS-6, "Component Parts
Location".
JPMIA1346ZZ
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-21
< FUNCTION DIAGNOSIS >
[FOR EUROPE]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM) INFOID:0000000005000851
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
: Applicable item
NOTE:
*1: At models with light and rain sensor or rain sensor this mode is displayed, but is not used.
*2: This item is displayed, but is not used.
*3: At models without RAP system this mode is displayed, but is not used.
Diagnosis mode Function Description
Work Support Changes the setting for each system function.
Self Diagnostic Result Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM. Refer to CONSULT-III opera-
tion manual.
Data Monitor The BCM input/output signals are displayed.
Active Test The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification The BCM part number is displayed.
Configuration
Read and save the vehicle specification.
Write the vehicle specification when replacing BCM.
System Sub system selection item
Diagnosis mode
Work Support Data Monitor Active Test
Door lock DOOR LOCK
Rear window defogger REAR DEFOGGER
Warning chime BUZZER
Interior room lamp timer INT LAMP
Exterior lamp HEAD LAMP
Wiper and washer WIPER
*
1
Turn signal and hazard warning lamps FLASHER
AIR CONDITONER*
2
Intelligent Key system
Engine start system
INTELLIGENT KEY
Combination switch COMB SW
Body control system BCM
NVIS - NATS IMMU
Interior room lamp battery saver BATTERY SAVER
Trunk lid open TRUNK
Vehicle security system THEFT ALM
RAP system
RETAINED PWR*
3
CONFRM ID ALL
The key ID that the key slot receives is not recognized by any key ID registered
to BCM.
Yet
The key ID that the key slot receives is recognized by any key ID registered to
BCM.
Done
CONFIRM ID4
The key ID that the key slot receives is not recognized by the fourth key ID regis-
tered to BCM.
Yet
The key ID that the key slot receives is recognized by the fourth key ID registered
to BCM.
Done
CONFIRM ID3
The key ID that the key slot receives is not recognized by the third key ID regis-
tered to BCM.
Yet
The key ID that the key slot receives is recognized by the third key ID registered
to BCM.
Done
CONFIRM ID2
The key ID that the key slot receives is not recognized by the second key ID reg-
istered to BCM.
Yet
The key ID that the key slot receives is recognized by the second key ID regis-
tered to BCM.
Done
CONFIRM ID1
The key ID that the key slot receives is not recognized by the first key ID regis-
tered to BCM.
Yet
The key ID that the key slot receives is recognized by the first key ID registered
to BCM.
Done
TP 4
The ID of fourth Intelligent Key is not registered to BCM Yet
The ID of fourth Intelligent Key is registered to BCM Done
TP 3
The ID of third Intelligent Key is not registered to BCM Yet
The ID of third Intelligent Key is registered to BCM Done
TP 2
The ID of second Intelligent Key is not registered to BCM Yet
The ID of second Intelligent Key is registered to BCM Done
TP 1
The ID of first Intelligent Key is not registered to BCM Yet
The ID of first Intelligent Key is registered to BCM Done
Monitor Item Condition Value/Status
BCS
BCM (BODY CONTROL MODULE)
BCS-53
< ECU DIAGNOSIS >
[FOR EUROPE]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
TERMINAL LAYOUT
PHYSICAL VALUES
JPMIA0062ZZ
BCS-54
< ECU DIAGNOSIS >
[FOR EUROPE]
BCM (BODY CONTROL MODULE)
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output +
1
(W)
Ground Battery power supply Input Ignition switch OFF Battery voltage
2
(W)*
1
(Y)*
2
Ground
P/W power supply
(BAT)
Output Ignition switch OFF 12 V
3
(Y)*
1
(O)*
2
Ground
P/W power supply
(RAP/IGN)
Output Ignition switch ON 12 V
4
(R)
Ground
Interior room lamp
power supply
Output
Interior room lamp battery saver is activated.
(Cuts the interior room lamp power supply)
0 V
Interior room lamp battery saver is not acti-
vated.
(Outputs the interior room lamp power sup-
ply)
12 V
5*
3
(V)
Ground Super lock Output
Super lock ac-
tuator
Actuator is activated 12 V
Actuator is not activated 0 V
8
(V)
Ground
All doors, fuel lid
LOCK
Output
All doors, fuel
lid
LOCK
(Actuator is activated)
12 V
Other than LOCK
(Actuator is not activated)
0 V
9
(G)
Ground
Driver door, fuel lid
UNLOCK
Output
Driver door,
fuel lid
UNLOCK
(Actuator is activated)
12 V
Other than UNLOCK
(Actuator is not activated)
0 V
10
(G)*
1
(BR)*
2
Ground
Passenger door UN-
LOCK
Output
Passenger
door
UNLOCK
(Actuator is activated)
12 V
Other than UNLOCK
(Actuator is not activated)
0 V
11
(BR)*
1
(R)*
2
Ground Battery power supply Input Ignition switch OFF Battery voltage
13
(B)
Ground Ground Ignition switch ON 0 V
15
(Y)
Ground ACC indicator lamp Output Ignition switch
OFF (LOCK indicator is
not illuminated)
Battery voltage
ACC 0 V
17
(W)*
1
(V)*
2
Ground
Turn signal RH (Front
and side)
Output
Ignition switch
ON
Turn signal switch OFF 0 V
Turn signal switch RH
6.5 V
PKID0926E
BCS
BCM (BODY CONTROL MODULE)
BCS-55
< ECU DIAGNOSIS >
[FOR EUROPE]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
18
(O)*
1
(LG)*
2
Ground
Turn signal LH (Front
and side)
Output
Ignition switch
ON
Turn signal switch OFF 0 V
Turn signal switch LH
6.5 V
19
(P)*
1
(SB)*
2
Ground
Room lamp timer
control
Output
Interior room
lamp
OFF 12 V
ON 0 V
20
(V)
Ground Turn signal RH (Rear) Output
Ignition switch
ON
Turn signal switch OFF 0 V
Turn signal switch RH
6.5 V
23
(L)
Ground Back door open Output Back door
OPEN
(Back door opener actua-
tor is activated)
12 V
Other than OPEN
(Back door opener actua-
tor is not activated)
0 V
24
(O)
Ground Rear fog lamp Output Rear fog lamp
OFF 0 V
ON 12 V
25
(LG)*
1
(G)*
2
Ground Turn signal LH (Rear) Output
Ignition switch
ON
Turn signal switch OFF 0 V
Turn signal switch LH
6.5 V
26
(G)
Ground Rear wiper Output Rear wiper
OFF (Stopped) 0 V
ON (Operated) 12 V
30
(R)
Ground Luggage room lamp Output
Luggage room
lamp
ON 0 V
OFF 12 V
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output +
PKID0926E
PKID0926E
PKID0926E
BCS-56
< ECU DIAGNOSIS >
[FOR EUROPE]
BCM (BODY CONTROL MODULE)
34
(G)*
1
(SB)*
2
Ground
Luggage room anten-
na ()
Output
Ignition switch
OFF
When Intelligent Key is in
the passenger compart-
ment
When Intelligent Key is not
in the passenger compart-
ment
35
(R)*
1
(V)*
2
Ground
Luggage room anten-
na (+)
Output
Ignition switch
OFF
When Intelligent Key is in
the passenger compart-
ment
When Intelligent Key is not
in the passenger compart-
ment
38
(B)
Ground
Rear bumper anten-
na ()
Output
When the back
door request
switch is oper-
ated with igni-
tion switch
OFF
When Intelligent Key is in
the antenna detection
area
When Intelligent Key is not
in the antenna detection
area
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output +
JMKIA0062GB
JMKIA0063GB
JMKIA0062GB
JMKIA0063GB
JMKIA0062GB
JMKIA0063GB
BCS
BCM (BODY CONTROL MODULE)
BCS-57
< ECU DIAGNOSIS >
[FOR EUROPE]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
39
(W)
Ground
Rear bumper anten-
na (+)
Output
When the back
door request
switch is oper-
ated with igni-
tion switch
OFF
When Intelligent Key is in
the antenna detection
area
When Intelligent Key is not
in the antenna detection
area
47
(V)*
1
(Y)*
2
Ground
Ignition relay (IPDM
E/R) control
Output Ignition switch
OFF or ACC 12 V
ON 0 V
52
(SB)*
1
(P)*
2
Ground Starter relay control Output
Ignition switch
ON (A/T mod-
els)
When selector lever is in P
or N position
12 V
When selector lever is not
in P or N position
0 V
Ignition switch ON (M/T models) Battery voltage
61
(W)
Ground
Back door opener re-
quest switch
Input
Back door
opener request
switch
ON (Pressed) 0 V
OFF (Not pressed)
1.0 V
64
(G)*
1
(V)*
2
Ground
Intelligent Key warn-
ing buzzer
Output
Intelligent Key
warning buzzer
Sounding 0 V
Not sounding 12 V
65
(O)
Ground
Rear wiper stop posi-
tion
Input Rear wiper
In stop position
1.0 V
Not in stop position 0 V
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output +
JMKIA0062GB
JMKIA0063GB
JPMIA0016GB
JPMIA0016GB
BCS-58
< ECU DIAGNOSIS >
[FOR EUROPE]
BCM (BODY CONTROL MODULE)
66
(R)
Ground Back door switch Input
Back door
switch
OFF (When back door
closes)
11.8 V
ON (When back door
opens)
0 V
67
(GR)
Ground
Back door opener
switch
Input
Back door
opener switch
Pressed 0 V
Not pressed
11.8 V
72
(R)
Ground
Room antenna ()
(Center console)
Output
Ignition switch
OFF
When Intelligent Key is in
the passenger compart-
ment
When Intelligent Key is not
in the passenger compart-
ment
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output +
JPMIA0011GB
JPMIA0011GB
JMKIA0062GB
JMKIA0063GB
BCS
BCM (BODY CONTROL MODULE)
BCS-59
< ECU DIAGNOSIS >
[FOR EUROPE]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
73
(G)
Ground
Room antenna (+)
(Center console)
Output
Ignition switch
OFF
When Intelligent Key is in
the passenger compart-
ment
When Intelligent Key is not
in the passenger compart-
ment
74
(SB)
Ground
Passenger door an-
tenna ()
Output
When the pas-
senger door re-
quest switch is
operated with
ignition switch
OFF
When Intelligent Key is in
the antenna detection
area
When Intelligent Key is not
in the antenna detection
area
75
(BR)
Ground
Passenger door an-
tenna (+)
Output
When the pas-
senger door re-
quest switch is
operated with
ignition switch
OFF
When Intelligent Key is in
the antenna detection
area
When Intelligent Key is not
in the antenna detection
area
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output +
JMKIA0062GB
JMKIA0063GB
JMKIA0062GB
JMKIA0063GB
JMKIA0062GB
JMKIA0063GB
BCS-60
< ECU DIAGNOSIS >
[FOR EUROPE]
BCM (BODY CONTROL MODULE)
76
(V)
Ground
Driver door antenna
()
Output
When the driv-
er door request
switch is oper-
ated with igni-
tion switch
OFF
When Intelligent Key is in
the antenna detection
area
When Intelligent Key is not
in the antenna detection
area
77
(LG)
Ground
Driver door antenna
(+)
Output
When the driv-
er door request
switch is oper-
ated with igni-
tion switch
OFF
When Intelligent Key is in
the antenna detection
area
When Intelligent Key is not
in the antenna detection
area
80
(GR)
Ground
NATS antenna amp
(Built in key slot)
Input/
Output
During waiting
Ignition switch is pressed
while inserting the Intelli-
gent Key into the key slot.
Just after pressing ignition
switch. Pointer of tester should
move.
81
(W)
Ground
NATS antenna amp
(Built in key slot)
Input/
Output
During waiting
Ignition switch is pressed
while inserting the Intelli-
gent Key into the key slot.
Just after pressing ignition
switch. Pointer of tester should
move.
82
(R)
Ground
Ignition relay [Fuse
block (J/B)] control
Output Ignition switch
OFF or ACC 0 V
ON 12 V
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output +
JMKIA0062GB
JMKIA0063GB
JMKIA0062GB
JMKIA0063GB
BCS
BCM (BODY CONTROL MODULE)
BCS-61
< ECU DIAGNOSIS >
[FOR EUROPE]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
83
(GR)*
1
(Y)*
2
Ground
Remote keyless entry
receiver communica-
tion
Input/
Output
During waiting
When operating either button on the Intelli-
gent Key
85*
4
(G)
Ground Alarm link
Input/
Output
Vehicle securi-
ty system
Disarmed phase 12 V
Pre-armed phase or
armed phase
86*
5
(O)
Ground Audio/Dongle link
Input/
Output
During waiting
Ignition switch is pressed
while inserting the Intelli-
gent Key into the key slot.
Just after pressing ignition
switch. Pointer of tester should
move.
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output +
JMKIA0064GB
JMKIA0065GB
NNKIA0175ZZ
BCS-62
< ECU DIAGNOSIS >
[FOR EUROPE]
BCM (BODY CONTROL MODULE)
87
(BR)
Ground
Combination switch
INPUT 5
Input
Combination
switch
All switches OFF
(Wiper volume dial 4)
1.4 V
Rear fog lamp switch ON
(Wiper volume dial 4)
1.3 V
Rear wiper switch ON
(Wiper volume dial 4)
1.3 V
Any of the conditions be-
low with all switches OFF
Wiper volume dial 1
Wiper volume dial 2
Wiper volume dial 6
Wiper volume dial 7
1.3 V
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output +
JPMIA0041GB
JPMIA0038GB
JPMIA0039GB
JPMIA0040GB
BCS
BCM (BODY CONTROL MODULE)
BCS-63
< ECU DIAGNOSIS >
[FOR EUROPE]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
88
(V)
Ground
Combination switch
INPUT 3
Input
Combination
switch
All switches OFF
(Wiper volume dial 4)
1.4 V
Lighting switch HI
(Wiper volume dial 4)
1.3 V
Lighting switch 2ND
(Wiper volume dial 4)
1.3 V
Rear washer switch ON
(Wiper volume dial 4)
1.3 V
Any of the conditions be-
low with all switches OFF
Wiper volume dial 1
Wiper volume dial 2
Wiper volume dial 3
1.3 V
89
(BR)
Ground
Push-button ignition
switch (Push switch)
Input
Push-button ig-
nition switch
(Push switch)
Pressed 0 V
Not pressed Battery voltage
90
(P)
Ground CAN-L
Input/
Output
91
(L)
Ground CAN-H
Input/
Output
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output +
JPMIA0041GB
JPMIA0036GB
JPMIA0037GB
JPMIA0039GB
JPMIA0040GB
BCS-64
< ECU DIAGNOSIS >
[FOR EUROPE]
BCM (BODY CONTROL MODULE)
92
(LG)
Ground Key slot illumination Output
Key slot illumi-
nation
OFF 12 V
Blinking
6.5 V
ON 0 V
93
(V)
Ground ON indicator lamp Output Ignition switch
OFF (LOCK indicator is
not illuminated)
Battery voltage
ON 0 V
95
(O)
Ground ACC relay control Output Ignition switch
OFF 0 V
ACC or ON 12 V
96*
6
(Y)
Ground
Control device (De-
tention switch) power
supply
Output 12 V
97
(L)
Ground
Steering lock condi-
tion No. 1
Input Steering lock
LOCK status 0 V
UNLOCK status 12 V
98
(P)
Ground
Steering lock condi-
tion No. 2
Input Steering lock
LOCK status 12 V
UNLOCK status 0 V
99*
7
(R)*
8
(BR)*
9
Ground
Selector lever P posi-
tion switch (A/T mod-
els)
Input
Selector lever
P position 0 V
Any position other than P 12 V
Clutch pedal position
switch (M/T models
without ASCD and
SynchroRev Match
mode)
Clutch pedal
position switch
OFF (Clutch pedal is de-
pressed)
0 V
ON (Clutch pedal is not
depressed)
Battery voltage
100
(GR)*
1
(G)*
2
Ground
Passenger door re-
quest switch
Input
Passenger
door request
switch
ON (Pressed) 0 V
OFF (Not pressed)
1.0 V
101
(Y)*
1
(SB)*
2
Ground
Driver door request
switch
Input
Driver door re-
quest switch
ON (Pressed) 0 V
OFF (Not pressed)
1.0 V
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output +
JPMIA0015GB
JPMIA0016GB
JPMIA0016GB
BCS
BCM (BODY CONTROL MODULE)
BCS-65
< ECU DIAGNOSIS >
[FOR EUROPE]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
102
(O)
Ground
Blower fan motor re-
lay control
Output Ignition switch
OFF or ACC 0 V
ON 12 V
103
(LG)
Ground
Remote keyless entry
receiver power sup-
ply
Output Ignition switch OFF 12 V
105*
3
(V)
Ground
Door lock status indi-
cator lamp
Output
Door lock sta-
tus indicator
lamp
OFF 0 V
ON 12 V
106
(W)
Ground
Steering lock unit
power supply
Output Ignition switch
OFF or ACC 12 V
ON 0 V
107
(LG)
Ground
Combination switch
INPUT 1
Input
Combination
switch
(Wiper volume
dial 4)
All switches OFF
1.4 V
Turn signal switch LH
1.3 V
Turn signal switch RH
1.3 V
Front wiper switch LO
1.3 V
Front washer switch ON
1.3 V
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output +
JPMIA0041GB
JPMIA0037GB
JPMIA0036GB
JPMIA0038GB
JPMIA0039GB
BCS-66
< ECU DIAGNOSIS >
[FOR EUROPE]
BCM (BODY CONTROL MODULE)
108
(R)
Ground
Combination switch
INPUT 4
Input
Combination
switch
All switches OFF
(Wiper volume dial 4)
1.4 V
Lighting switch AUTO
(Wiper volume dial 4)
1.3 V
Lighting switch 1ST
(Wiper volume dial 4)
1.3 V
Rear wiper switch INT
(Wiper volume dial 4)
1.3 V
Any of the conditions be-
low with all switches OFF
Wiper volume dial 1
Wiper volume dial 5
Wiper volume dial 6
1.3 V
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output +
JPMIA0041GB
JPMIA0038GB
JPMIA0036GB
JPMIA0040GB
JPMIA0039GB
BCS
BCM (BODY CONTROL MODULE)
BCS-67
< ECU DIAGNOSIS >
[FOR EUROPE]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
109
(Y)
Ground
Combination switch
INPUT 2
Input
Combination
switch
(Wiper volume
dial 4)
All switches OFF
1.4 V
Lighting switch PASS
1.3 V
Lighting switch 2ND
1.3 V
Front wiper switch AUTO
1.3 V
Front wiper switch HI
1.3 V
110
(P)*
1
(G)*
2
Ground Hazard switch Input Hazard switch
ON 0 V
OFF
1.1 V
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output +
JPMIA0041GB
JPMIA0037GB
JPMIA0036GB
JPMIA0038GB
JPMIA0040GB
JPMIA0012GB
BCS-68
< ECU DIAGNOSIS >
[FOR EUROPE]
BCM (BODY CONTROL MODULE)
111
(Y)
Ground
Steering lock unit
communication
Input/
Output
Steering lock
LOCK status 12 V
LOCK or UNLOCK
For 15 seconds after UN-
LOCK
12 V
15 seconds or later after
UNLOCK
0 V
112*
4
(R)
Ground
Light and rain sensor
serial link
Input/
Output
Ignition switch ON
8.7 V
113*
10
(O)
Ground Optical sensor Input
Ignition switch
ON
When bright outside of the
vehicle
Close to 5 V
When dark outside of the
vehicle
Close to 0 V
114*
11
(R)
Ground
Clutch interlock
switch
Input
Clutch interlock
switch
OFF (Clutch pedal is not
depressed)
0 V
ON (Clutch pedal is de-
pressed)
Battery voltage
115*
4
(O)
Ground Shock sensor Input Ignition switch
OFF 0 V
ACC 5.0 V
ON
2.5 V
116
(SB)
Ground Stop lamp switch 1 Input Battery voltage
117*
4
(L)
Ground Sensor cancel switch Input
Sensor cancel
switch
OFF (Not pressed)
1.1 V
ON (Pressed 0 V
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output +
JMKIA0066GB
JPMIA0156GB
JPMIA1034GB
JPMIA0012GB
BCS
BCM (BODY CONTROL MODULE)
BCS-69
< ECU DIAGNOSIS >
[FOR EUROPE]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
118
(P)
Ground Stop lamp switch 2 Input
Stop lamp
switch
OFF (Brake pedal is not
depressed)
0 V
ON (Brake pedal is de-
pressed)
Battery voltage
119
(SB)
Ground
Driver side door lock
assembly (Unlock
sensor)
Input Driver door
LOCK status
(Unlock sensor switch
OFF)
1.1 V
UNLOCK status
(Unlock switch sensor
ON)
0 V
120*
11
(O)
Ground Back up lamp switch Input
Ignition switch
ON
Control lever in reverse
position
Battery voltage
Control lever in any posi-
tion other than reverse
0 V
121
(R)
Ground Key slot switch Input
When the Intelligent Key is inserted into key
slot
12 V
When the Intelligent Key is not inserted into
key slot
0 V
123
(W)
Ground IGN feedback Input Ignition switch
OFF or ACC 0 V
ON Battery voltage
124
(LG)
Ground
Passenger door
switch
Input
Passenger
door switch
OFF (Door close)
11.8 V
ON (Door open) 0 V
130*
12
(L)
Ground
Rear window defog-
ger switch
Input
Ignition switch
ON
Rear window defogger
switch OFF
1.1 V
Rear window defogger
switch ON
0 V
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output +
JPMIA0012GB
JPMIA0011GB
JPMIA0012GB
BCS-70
< ECU DIAGNOSIS >
[FOR EUROPE]
BCM (BODY CONTROL MODULE)
132
(Y)*
1
(V)*
2
Ground
Power window switch
communication
Input/
Output
Ignition switch ON
10.2 V
Ignition switch OFF or ACC 12 V
133
(G)*
1
(R)*
2
Ground
Push-button ignition
switch illumination
Output
Push-button ig-
nition switch il-
lumination
ON (Tail lamps OFF) 9.5 V
ON (Tail lamps ON)
NOTE:
The pulse width of this wave is
varied by the illumination bright-
ening/dimming level.
OFF 0 V
134
(GR)
Ground LOCK indicator lamp Output
LOCK indicator
lamp
OFF Battery voltage
ON 0 V
137
(P)*
1
(O)*
2
Ground
Receiver and sensor
ground
Input Ignition switch ON 0 V
138*
10
(V)
Ground Sensor power supply Output Ignition switch
OFF 0 V
ACC or ON 5.0 V
140*
13
(G)
Ground
Selector lever P/N
position (A/T models)
Input
Selector lever
P or N position 12 V
Except P and N positions 0 V
Park/neutral position
switch (M/T models)
Ignition switch
ON
Control lever in neutral po-
sition
Battery voltage
Control lever in any posi-
tion other than neutral
0
141
(Y)*
1
(G)*
2
Ground Security indicator Output
Security indica-
tor
ON 0 V
Blinking
11.3 V
OFF 12 V
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output +
JPMIA0013GB
JPMIA0159GB
JPMIA0014GB
BCS
BCM (BODY CONTROL MODULE)
BCS-71
< ECU DIAGNOSIS >
[FOR EUROPE]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
142
(O)
Ground
Combination switch
OUTPUT 5
Output
Combination
switch
(Wiper volume
dial 4)
All switches OFF 0 V
Lighting switch 1ST
10.7 V
Lighting switch HI
Lighting switch 2ND
Turn signal switch RH
143
(P)
Ground
Combination switch
OUTPUT 1
Output
Combination
switch
All switches OFF
(Wiper volume dial 4)
0 V
Front wiper switch HI
(Wiper volume dial 4)
10.7 V
Rear wiper switch INT
(Wiper volume dial 4)
Any of the conditions be-
low with all switches OFF
Wiper volume dial 1
Wiper volume dial 2
Wiper volume dial 3
Wiper volume dial 6
Wiper volume dial 7
144
(G)
Ground
Combination switch
OUTPUT 2
Output
Combination
switch
All switches OFF
(Wiper volume dial 4)
0 V
Front washer switch ON
(Wiper volume dial 4)
10.7 V
Rear wiper switch ON
(Wiper volume dial 4)
Rear washer switch ON
(Wiper volume dial 4)
Any of the conditions be-
low with all switches OFF
Wiper volume dial 1
Wiper volume dial 5
Wiper volume dial 6
145
(L)
Ground
Combination switch
OUTPUT 3
Output
Combination
switch
(Wiper volume
dial 4)
All switches OFF 0 V
Front wiper switch AUTO
10.7 V
Front wiper switch LO
Lighting switch AUTO
Rear fog lamp switch ON
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output +
JPMIA0031GB
JPMIA0032GB
JPMIA0033GB
JPMIA0034GB
BCS-72
< ECU DIAGNOSIS >
[FOR EUROPE]
BCM (BODY CONTROL MODULE)
*1: LHD models
*2: RHD models
*3: Only RHD models
*4: Except for Russia
*5: LHD models with BOSE system (without NAVI) except for Russia, and RHD models
*6: Only A/T models
*7: M/T models without ASCD and SynchroRev Match mode, and A/T models
*8: A/T models
*9: M/T models without ASCD and SynchroRev Match mode
*10: For Russia
*11: Only M/T models
*12: Without NAVI
*13:M/T models with SynchroRev Match mode, and A/T models
146
(SB)
Ground
Combination switch
OUTPUT 4
Output
Combination
switch
(Wiper volume
dial 4)
All switches OFF 0 V
Lighting switch 2ND
10.7 V
Lighting switch PASS
Turn signal switch LH
150
(GR)
Ground Driver door switch Input
Driver door
switch
OFF (Door close)
11.8 V
ON (Door open) 0 V
151
(G)
Ground
Rear window defog-
ger relay control
Output
Rear window
defogger
Active 0 V
Not activated Battery voltage
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output +
JPMIA0035GB
JPMIA0011GB
BCS
BCM (BODY CONTROL MODULE)
BCS-73
< ECU DIAGNOSIS >
[FOR EUROPE]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
Wiring Diagram - BCM (LHD models) - INFOID:0000000005000979
JCMWM3896GB
BCS-74
< ECU DIAGNOSIS >
[FOR EUROPE]
BCM (BODY CONTROL MODULE)
JCMWM3897GB
BCS
BCM (BODY CONTROL MODULE)
BCS-75
< ECU DIAGNOSIS >
[FOR EUROPE]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
JCMWM3898GB
BCS-76
< ECU DIAGNOSIS >
[FOR EUROPE]
BCM (BODY CONTROL MODULE)
JCMWM3899GB
BCS
BCM (BODY CONTROL MODULE)
BCS-77
< ECU DIAGNOSIS >
[FOR EUROPE]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
JCMWM3900GB
BCS-78
< ECU DIAGNOSIS >
[FOR EUROPE]
BCM (BODY CONTROL MODULE)
JCMWM3901GB
BCS
BCM (BODY CONTROL MODULE)
BCS-79
< ECU DIAGNOSIS >
[FOR EUROPE]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
Wiring Diagram - BCM (RHD models) - INFOID:0000000005000980
JCMWM3902GB
BCS-80
< ECU DIAGNOSIS >
[FOR EUROPE]
BCM (BODY CONTROL MODULE)
JCMWM3903GB
BCS
BCM (BODY CONTROL MODULE)
BCS-81
< ECU DIAGNOSIS >
[FOR EUROPE]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
JCMWM3904GB
BCS-82
< ECU DIAGNOSIS >
[FOR EUROPE]
BCM (BODY CONTROL MODULE)
JCMWM3905GB
BCS
BCM (BODY CONTROL MODULE)
BCS-83
< ECU DIAGNOSIS >
[FOR EUROPE]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
JCMWM3906GB
BCS-84
< ECU DIAGNOSIS >
[FOR EUROPE]
BCM (BODY CONTROL MODULE)
JCMWM3907GB
BCS
BCM (BODY CONTROL MODULE)
BCS-85
< ECU DIAGNOSIS >
[FOR EUROPE]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
Fail-safe INFOID:0000000005000885
FAIL-SAFE CONTROL BY DTC
BCM performs fail-safe control when any DTC are detected.
JCMWM3908GB
BCS-86
< ECU DIAGNOSIS >
[FOR EUROPE]
BCM (BODY CONTROL MODULE)
Display contents of CONSULT Fail-safe Cancellation
B2013: ID DISCORD BCM-S/L Inhibit engine cranking Erase DTC
B2014: CHAIN OF S/L-BCM Inhibit engine cranking Erase DTC
B2190: NATS ANTENNA AMP Inhibit engine cranking Erase DTC
B2191: DIFFERENCE OF KEY Inhibit engine cranking Erase DTC
B2192: ID DISCORD BCM-ECM Inhibit engine cranking Erase DTC
B2193: CHAIN OF BCM-ECM Inhibit engine cranking Erase DTC
B2195: ANTI SCANNING Inhibit engine cranking Ignition switch ON OFF
B2196: DONGLE NG Inhibit engine cranking Erase DTC
B2557: VEHICLE SPEED Inhibit steering lock
When normal vehicle speed signals are received from ABS actua-
tor and electric unit (control unit) for 500 ms
B2560: STARTER CONT RELAY Inhibit engine cranking
500 ms after the following CAN signal communication status be-
comes consistent
Starter control relay signal
Starter relay status signal
B2601: SHIFT POSITION Inhibit steering lock
500 ms after the following signal reception status becomes consis-
tent
Selector lever P position switch signal
P range signal (CAN)
B2602: SHIFT POSITION Inhibit steering lock
5 seconds after the following BCM recognition conditions are ful-
filled
Ignition switch is in the ON position
Selector lever P position switch signal: Except P position (battery
voltage)
Vehicle speed: 4 km/h (2.5 MPH) or more
B2603: SHIFT POSI STATUS Inhibit steering lock
500 ms after the following BCM recognition conditions are fulfilled
Ignition switch is in the ON position
Selector lever P position switch signal: Except P position (battery
voltage)
Selector lever P/N position signal: Except P and N positions (0 V)
B2604: PNP SW Inhibit steering lock
500 ms after any of the following BCM recognition conditions are
fulfilled
Status 1
- Ignition switch is in the ON position
- Selector lever P/N position signal: P and N position (battery volt-
age)
- P range signal or N range signal (CAN): ON
Status 2
- Ignition switch is in the ON position
- Selector lever P/N position signal: Except P and N positions (0 V)
- P range signal and N range signal (CAN): OFF
B2605: PNP SW Inhibit steering lock
500 ms after any of the following BCM recognition conditions are
fulfilled
Status 1
- Ignition switch is in the ON position
- Selector lever P/N position signal: Except P and N positions (0 V)
- Interlock/PNP switch signal (CAN): OFF
Status 2
- Ignition switch is in the ON position
- Selector lever P/N position signal: P or N position (battery volt-
age)
- PNP switch signal (CAN): ON
B2606: S/L RELAY Inhibit engine cranking
500 ms after the following CAN signal communication status be-
comes consistent
Steering lock relay signal (Request signal)
Steering lock relay signal (Condition signal)
BCS
BCM (BODY CONTROL MODULE)
BCS-87
< ECU DIAGNOSIS >
[FOR EUROPE]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
HIGH FLASHER OPERATION
BCM detects the turn signal lamp circuit status by the current value.
BCM increases the turn signal lamp blinking speed if the bulb or harness open is detected with the turn signal
lamp operating.
NOTE:
B2607: S/L RELAY Inhibit engine cranking
500 ms after the following CAN signal communication status has
becomes consistent
Steering lock relay signal (Request signal)
Steering lock relay signal (Condition signal)
B2608: STARTER RELAY Inhibit engine cranking
500 ms after the following signal communication status becomes
consistent
Starter motor relay control signal
Starter relay status signal (CAN)
B2609: S/L STATUS
Inhibit engine cranking
Inhibit steering lock
When the following steering lock conditions agree
BCM steering lock control status
Steering lock condition No. 1 signal status
Steering lock condition No. 2 signal status
B260A: IGNITION RELAY Inhibit engine cranking
500 ms after the following conditions are fulfilled
IGN relay (IPDM E/R) control signal: OFF (Battery voltage)
Ignition ON signal (CAN to IPDM E/R): OFF (Request signal)
Ignition ON signal (CAN from IPDM E/R): OFF (Condition signal)
B260F: ENG STATE SIG LOST
Maintains the power supply
position attained at the time
of DTC detection
When any of the following conditions are fulfilled
Power position changes to ACC
Receives engine status signal (CAN)
B2612: S/L STATUS
Inhibit engine cranking
Inhibit steering lock
When any of the following conditions are fulfilled
Steering lock unit status signal (CAN) is received normally
The BCM steering lock control status matches the steering lock
status recognized by the steering lock unit status signal (CAN
from IPDM E/R)
B2617: STARTER RELAY CIRC Inhibit engine cranking
1 second after the starter motor relay control inside BCM becomes
normal
B2618: BCM Inhibit engine cranking
1 second after the ignition relay (IPDM E/R) control inside BCM be-
comes normal
B2619: BCM Inhibit engine cranking
1 second after the steering lock unit power supply output control in-
side BCM becomes normal
B261E: VEHICLE TYPE Inhibit engine cranking BCM initialization
B2620: NEUTRAL SW
Inhibit engine cranking
(Only when try to start the
engine while depressing
brake pedal and shifting to
the neutral position)
When any of the following BCM recognition conditions are fulfilled
Status 1
- Back up lamp switch signal: ON (Battery voltage)
- Park/neutral position switch signal: OFF (0 V)
Status 2
- Back up lamp switch signal: OFF (0 V)
- Park/neutral position switch signal: ON (Battery voltage)
Status 3
- Back up lamp switch signal: OFF (0 V)
- Park/neutral position switch signal: OFF (0 V)
B26E8: CLUTCH SW Inhibit engine cranking
When any of the following BCM recognition conditions are fulfilled
Status 1
- Clutch switch signal (CAN from ECM): ON
- Clutch interlock switch signal: OFF (0 V)
Status 2
- Clutch switch signal (CAN from ECM): OFF
- Clutch interlock switch signal: ON (Battery voltage)
B26E9: S/L STATUS
Inhibit engine cranking
Inhibit steering lock
When BCM transmits the LOCK request signal to steering lock unit,
and receives LOCK response signal from steering lock unit, the fol-
lowing conditions are fulfilled
Steering condition No. 1 signal: LOCK (0 V)
Steering condition No. 2 signal: LOCK (Battery voltage)
Display contents of CONSULT Fail-safe Cancellation
BCS-88
< ECU DIAGNOSIS >
[FOR EUROPE]
BCM (BODY CONTROL MODULE)
The blinking speed is normal while activating the hazard warning lamp.
FAIL-SAFE CONTROL BY LIGHT AND RAIN SENSOR MALFUNCTION
BCM detects the light and rain sensor serial link error and the light and rain sensor malfunction.
BCM controls the following fail-safe when light and rain sensor has a malfunction.
Fail-safe Control
Auto light control: Headlamp low beam, parking lamp, license plate lamp and tail lamp are turned ON.
Front wiper control
- Front wiper switch AUTO and sensing rain drop: The condition just before the activation of fail-safe is main-
tained until the front wiper switch is turned OFF.
- Front wiper switch AUTO and not sensing rain drop: Front wiper is LO operation until the front wiper switch is
tured off.
REAR WIPER MOTOR PROTECTION
BCM detects the rear wiper stopping position according to the rear wiper stop position signal.
When the rear wiper stop position signal does not change for more than 5 seconds while driving the rear
wiper, BCM stops power supply to protect the rear wiper motor.
Condition of cancellation
1. More than 1 minute is passed after the rear wiper stop.
2. Turn rear wiper switch OFF.
3. Operate the rear wiper switch or rear washer switch.
DTC Inspection Priority Chart INFOID:0000000005000886
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.
Priority DTC
1 B2562: LOW VOLTAGE
2
U1000: CAN COMM
U1010: CONTROL UNIT (CAN)
3
B2190: NATS ANTENNA AMP
B2191: DIFFERENCE OF KEY
B2192: ID DISCORD BCM-ECM
B2193: CHAIN OF BCM-ECM
B2195: ANTI SCANNING
B2196: DONGLE NG
BCS
BCM (BODY CONTROL MODULE)
BCS-89
< ECU DIAGNOSIS >
[FOR EUROPE]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
DTC Index INFOID:0000000005000887
NOTE:
The details of time display are as follows.
CRNT: A malfunction is detected now.
PAST: A malfunction was detected in the past.
IGN counter is displayed on Freeze Frame Data. For details of Freeze Frame Data, refer to BCS-21, "COM-
MON ITEM : CONSULT-III Function (BCM - COMMON ITEM)".
4
B2013: ID DISCORD BCM-S/L
B2014: CHAIN OF S/L-BCM
B2553: IGNITION RELAY
B2555: STOP LAMP
B2556: PUSH-BTN IGN SW
B2557: VEHICLE SPEED
B2560: STARTER CONT RELAY
B2601: SHIFT POSITION
B2602: SHIFT POSITION
B2603: SHIFT POSI STATUS
B2604: PNP SW
B2605: PNP SW
B2606: S/L RELAY
B2607: S/L RELAY
B2608: STARTER RELAY
B2609: S/L STATUS
B260A: IGNITION RELAY
B260B: STEERING LOCK UNIT
B260C: STEERING LOCK UNIT
B260D: STEERING LOCK UNIT
B260F: ENG STATE SIG LOST
B2612: S/L STATUS
B2614: ACC RELAY CIRC
B2615: BLOWER RELAY CIRC
B2616: IGN RELAY CIRC
B2617: STARTER RELAY CIRC
B2618: BCM
B2619: BCM
B261A: PUSH-BTN IGN SW
B261E: VEHICLE TYPE
B2620: NEUTRAL SW
B26E8: CLUTCH SW
B26E9: S/L STATUS
B26EA: KEY REGISTRATION
U0415: VEHICLE SPEED SIG
5
B2622: INSIDE ANTENNA
B2623: INSIDE ANTENNA
Priority DTC
CONSULT display Fail-safe
Freeze Frame Data
Vehicle Speed
Odo/Trip Meter
Vehicle condition
Intelligent Key
warning lamp ON
Reference page
No DTC is detected.
further testing
may be required.
U1000: CAN COMM BCS-39
U1010: CONTROL UNIT (CAN) BCS-40
U0415: VEHICLE SPEED SIG BCS-41
B2013: ID DISCORD BCM-S/L SEC-65
B2014: CHAIN OF S/L-BCM SEC-66
B2190: NATS ANTENNA AMP SEC-55
BCS-90
< ECU DIAGNOSIS >
[FOR EUROPE]
BCM (BODY CONTROL MODULE)
B2191: DIFFERENCE OF KEY SEC-58
B2192: ID DISCORD BCM-ECM SEC-59
B2193: CHAIN OF BCM-ECM SEC-61
B2195: ANTI SCANNING SEC-62
B2196: DONGLE NG SEC-63
B2553: IGNITION RELAY PCS-51
B2555: STOP LAMP SEC-69
B2556: PUSH-BTN IGN SW SEC-72
B2557: VEHICLE SPEED SEC-74
B2560: STARTER CONT RELAY SEC-75
B2562: LOW VOLTAGE BCS-42
B2601: SHIFT POSITION SEC-76
B2602: SHIFT POSITION SEC-79
B2603: SHIFT POSI STATUS SEC-82
B2604: PNP SW SEC-85
B2605: PNP SW SEC-87
B2606: S/L RELAY SEC-89
B2607: S/L RELAY SEC-90
B2608: STARTER RELAY SEC-92
B2609: S/L STATUS SEC-94
B260A: IGNITION RELAY PCS-53
B260B: STEERING LOCK UNIT SEC-98
B260C: STEERING LOCK UNIT SEC-99
B260D: STEERING LOCK UNIT SEC-100
B260F: ENG STATE SIG LOST SEC-101
B2612: S/L STATUS SEC-107
B2614: ACC RELAY CIRC PCS-55
B2615: BLOWER RELAY CIRC PCS-58
B2616: IGN RELAY CIRC PCS-61
B2617: STARTER RELAY CIRC SEC-111
B2618: BCM PCS-64
B2619: BCM SEC-113
B261A: PUSH-BTN IGN SW PCS-65
B261E: VEHICLE TYPE
(Turn ON for 15
seconds)
SEC-119
B2620: NEUTRAL SW SEC-114
B2622: INSIDE ANTENNA
DLK-65 (With super
lock)
DLK-295 (Without
super lock)
B2623: INSIDE ANTENNA
DLK-67 (With super
lock)
DLK-297 (Without
super lock)
CONSULT display Fail-safe
Freeze Frame Data
Vehicle Speed
Odo/Trip Meter
Vehicle condition
Intelligent Key
warning lamp ON
Reference page
BCS
BCM (BODY CONTROL MODULE)
BCS-91
< ECU DIAGNOSIS >
[FOR EUROPE]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
B26E8: CLUTCH SW SEC-102
B26E9: S/L STATUS
(Turn ON for 15
seconds)
SEC-105
B26EA: KEY REGISTRATION
(Turn ON for 15
seconds)
SEC-106
CONSULT display Fail-safe
Freeze Frame Data
Vehicle Speed
Odo/Trip Meter
Vehicle condition
Intelligent Key
warning lamp ON
Reference page
BCS-92
< SYMPTOM DIAGNOSIS >
[FOR EUROPE]
COMBINATION SWITCH SYSTEM SYMPTOMS
SYMPTOM DIAGNOSIS
COMBINATION SWITCH SYSTEM SYMPTOMS
Symptom Table INFOID:0000000005030870
1. Perform Data Monitor of CONSULT-III to check for any malfunctioning item.
2. Check the malfunction combinations.
Malfunction item:
3. Identify the malfunctioning part from the agreed combination and repair or replace the part.
Malfunction
combination
Data monitor item
F
R
W
I
P
E
R
H
I
F
R
W
I
P
E
R
L
O
W
F
R
W
A
S
H
E
R
S
W
F
R
W
I
P
E
R
I
N
T
R
R
W
I
P
E
R
O
N
R
R
W
I
P
E
R
I
N
T
R
R
W
A
S
H
E
R
S
W
I
N
T
V
O
L
U
M
E
T
U
R
N
S
I
G
N
A
L
R
T
U
R
N
S
I
G
N
A
L
L
T
A
I
L
L
A
M
P
S
W
H
I
B
E
A
M
S
W
H
E
A
D
L
A
M
P
S
W
1
H
E
A
D
L
A
M
P
S
W
2
P
A
S
S
I
N
G
S
W
A
U
T
O
L
I
G
H
T
S
W
R
R
F
O
G
S
W
A
B
C
D
E
F
G
H
I
J
K All Items
L If only one item is detected or the item is not applicable to the combinations A to K
Malfunction
combination
Malfunctioning part Repair or replace
A Combination switch INPUT 1 circuit
Inspect the combination switch input circuit applicable to the malfunctioning
part. Refer to BCS-44, "Diagnosis Procedure".
B Combination switch INPUT 2 circuit
C Combination switch INPUT 3 circuit
D Combination switch INPUT 4 circuit
E Combination switch INPUT 5 circuit
F Combination switch OUTPUT 1 circuit
Inspect the combination switch output circuit applicable to the malfunction-
ing part. Refer to BCS-46, "Diagnosis Procedure".
G Combination switch OUTPUT 2 circuit
H Combination switch OUTPUT 3 circuit
I Combination switch OUTPUT 4 circuit
J Combination switch OUTPUT 5 circuit
K BCM Replace BCM. Refer to BCS-94, "Exploded View".
L Combination switch Replace the combination switch.
BCS
PRECAUTIONS
BCS-93
< PRECAUTION >
[FOR EUROPE]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER" INFOID:0000000005000889
The Supplemental Restraint System such as AIR BAG and SEAT BELT PRE-TENSIONER, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SRS AIR BAG and
SEAT BELT of this Service Manual.
WARNING:
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SRS AIR BAG.
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s)
with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly
causing serious injury.
When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution for Battery Service INFOID:0000000005000890
Before disconnecting the battery, lower both the driver and passenger windows. This will prevent any interfer-
ence between the window edge and the vehicle when the door is opened/closed. During normal operation, the
window slightly raises and lowers automatically to prevent any window to vehicle interference. The automatic
window function will not work with the battery disconnected.
BCS-94
< ON-VEHICLE REPAIR >
[FOR EUROPE]
BCM (BODY CONTROL MODULE)
ON-VEHICLE REPAIR
BCM (BODY CONTROL MODULE)
Exploded View INFOID:0000000005000945
CAUTION:
Before replacing BCM, perform READ CONFIGURATION to save or print current vehicle specifica-
tion. Refer to BCS-7, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM) : Descrip-
tion".
Removal and Installation INFOID:0000000005000946
CAUTION:
Before replacing BCM, perform READ CONFIGURATION to save or print current vehicle specifica-
tion. Refer to BCS-7, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM) : Descrip-
tion".
REMOVAL
1. Remove dash side finisher (passenger side). Refer to INT-14, "Exploded View".
2. Remove bolt and nut.
3. Remove BCM and disconnect the connector.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Be sure to perform WRITE CONFIGURATION when replacing BCM.
Be sure to perform the system initialization (NATS) when replacing BCM. Refer to BCS-7, "ADDI-
TIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM) : Special Repair Requirement".
1. BCM
JPMIA1343ZZ
BCS
COMBINATION SWITCH
BCS-95
< ON-VEHICLE REPAIR >
[FOR EUROPE]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
COMBINATION SWITCH
Exploded View INFOID:0000000005000947
Removal and Installation INFOID:0000000005000948
REMOVAL
1. Remove steering column cover. Refer to IP-11, "Exploded View".
2. Remove screws.
3. Disconnect the connector.
4. Pull up the combination switch to remove it.
INSTALLATION
Install in the reverse order of removal.
1. Combination switch 2. Combination switch connector
JPMIA1344ZZ
BCS-96
< FEATURES OF NEW MODEL >
[FOR GENERAL AREAS]
APPLICATION NOTICE
FEATURES OF NEW MODEL
APPLICATION NOTICE
How to Check Vehicle Type INFOID:0000000005047974
Check the vehicle type (refer to GI-21, "Model Variation") to use the service information in this section.
Application Service information
Europe (RH drive, LH drive)
FOR EUROPE
Russia and Ukraine
Australia, New Zealand and General areas (RH drive)
FOR GENERAL AREAS
Hong Kong, Singapore and Brunei
Middle East
General areas (LH drive)
South Africa FOR SOUTH AFRICA
BCS
INSPECTION AND ADJUSTMENT
BCS-97
< BASIC INSPECTION >
[FOR GENERAL AREAS]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
BASIC INSPECTION
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM)
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM) : Description
INFOID:0000000004699652
BEFORE REPLACEMENT
When replacing BCM, save or print current vehicle specification with CONSULT-III configuration before
replacement.
NOTE:
If READ CONFIGURATION can not be used, use the WRITE CONFIGURATION - Manual selection after
replacing BCM.
AFTER REPLACEMENT
CAUTION:
When replacing BCM, you must perform WRITE CONFIGURATION with CONSULT-III.
- Complete the procedure of WRITE CONFIGURATION in order.
- If you set incorrect WRITE CONFIGURATION, incidents might occur.
- Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
When replacing BCM, perform the system initialization (NATS).
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM) : Special Repair
Requirement INFOID:0000000004699653
1.SAVING VEHICLE SPECIFICATION
CONSULT-III Configuration
Perform READ CONFIGURATION to save or print current vehicle specification. Refer to BCS-97, "CONFIG-
URATION (BCM) : Description".
NOTE:
If READ CONFIGURATION can not be used, use the WRITE CONFIGURATION - Manual selection after
replacing BCM.
>> GO TO 2.
2.REPLACE BCM
Replace BCM. Refer to BCS-187, "Exploded View".
>> GO TO 3.
3.WRITING VEHICLE SPECIFICATION
CONSULT-III Configuration
Perform WRITE CONFIGURATION - Config file or WRITE CONFIGURATION - Manual selection to write
vehicle specification. Refer to BCS-98, "CONFIGURATION (BCM) : Special Repair Requirement".
>> GO TO 4.
4.INITIALIZE BCM (NATS)
Perform BCM initialization. (NATS)
>> WORK END
CONFIGURATION (BCM)
CONFIGURATION (BCM) : Description INFOID:0000000004699654
Vehicle specification needs to be written with CONSULT-III because it is not written after replacing BCM.
BCS-98
< BASIC INSPECTION >
[FOR GENERAL AREAS]
INSPECTION AND ADJUSTMENT
Configuration has three functions as follows
NOTE:
Manual setting item: Items which need selection by vehicle specifications
Automatic setting item: Items which are written in automatically (Setting can not be changed)
CAUTION:
When replacing BCM, you must perform WRITE CONFIGURATION with CONSULT-III.
Complete the procedure of WRITE CONFIGURATION in order.
If you set incorrect WRITE CONFIGURATION, incidents might occur.
Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
Never perform WRITE CONFIGURATION except for new BCM.
CONFIGURATION (BCM) : Special Repair Requirement INFOID:0000000004699655
1.WRITING MODE SELECTION
CONSULT-III Configuration
Select CONFIGURATION of BCM.
When writing saved data>>GO TO 2.
When writing manually>>GO TO 3.
2.PERFORM WRITE CONFIGURATION - CONFIG FILE
CONSULT-III Configuration
Perform WRITE CONFIGURATION - Config file.
>> WORK END
3.PERFORM WRITE CONFIGURATION - MANUAL SELECTION
CONSULT-III Configuration
1. Select "WRITE CONFIGURATION - Manual selection".
2. Identify the correct model and configuration list. Refer to BCS-99, "CONFIGURATION (BCM) : Configura-
tion list".
3. Confirm and/or change setting value for each item.
CAUTION:
Thoroughly read and understand the vehicle specification. Incorrect settings may result in abnor-
mal control of ECU.
4. Select "SETTING".
CAUTION:
Make sure to select SETTING even if the indicated configuration of brand new BCM is same as
the desirable configuration. If not, configuration which is set automatically by selecting vehicle
model can not be memorized.
5. When "COMMAND FINISHED", select "END".
>> GO TO 4.
4.OPERATION CHECK
Confirm that each function controlled by BCM operates normally.
>> WORK END
Function Description
READ CONFIGURATION
Reads the vehicle configuration of current BCM.
Saves the read vehicle configuration.
WRITE CONFIGURATION - Manual selection Writes the vehicle configuration with manual selection.
WRITE CONFIGURATION - Config file Writes the vehicle configuration with saved data.
BCS
INSPECTION AND ADJUSTMENT
BCS-99
< BASIC INSPECTION >
[FOR GENERAL AREAS]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
CONFIGURATION (BCM) : Configuration list INFOID:0000000004699656
CAUTION:
Thoroughly read and understand the vehicle specification. Incorrect settings may result in abnormal
control of ECU.
RHD WITH A/T MODELS
: Items which confirm vehicle specifications
RHD WITH M/T MODELS
MANUAL SETTING ITEM
NOTE
Items Setting value
AV C/U WITH WITHOUT
HANDLE RHD
THEFT ALM AREA WITHOUT MODE3
WITHOUT: Without vehicle security system
MODE3: With vehicle security system
ASCD CANCEL SW TYPE MODE2
TPMS WITH WITHOUT
Key Fob Type MODE6 MODE9
MODE6: Without panic alarm
MODE9: With panic alarm
AUTO SETTING ITEM
NOTE
Items Setting value
SELECTIVE UNLOCK SETTING WITHOUT
SELECTIVE UNLOCK WS WITHOUT
P/W UP/DOWN WITHOUT
P-POS WARN MODE1
ROOF FUNCTION W/O REQ SW
AUTO BACK DOOR WITHOUT
Trunk/Glass Hatch select Glass Hatch
Glass Hatch is indicated also for vehicles without a glass
hatch.
PANIC ALM TYPE MODE2
RAP FUNC SET MODE1
TR OPEN SW (INT) MODE1
DI LMP VARIAT MODE2
LIGHT RECOG MODE4
TRANSMISSION AT with ABS
RAIN SENSOR CONFIG WITHOUT
REAR WIPER WITH
H/L WASHER MODE3
HAZARD SW TYPE MODE1
BCM AC CONTROL MODE1
AUTO LOCK&UNLOCK FUNK WITHOUT
AUTO DOOR LOCK SELECT WITHOUT
AUTO DOOR UNLOCK SELECT WITHOUT
FOG ON WITH AUTO LIGHT WITH
BCS-100
< BASIC INSPECTION >
[FOR GENERAL AREAS]
INSPECTION AND ADJUSTMENT
: Items which confirm vehicle specifications
LHD WITH A/T MODELS
MANUAL SETTING ITEM
NOTE
Items Setting value
AV C/U WITH WITHOUT
HANDLE RHD
THEFT ALM AREA WITHOUT MODE3
WITHOUT: Without vehicle security system
MODE3: With vehicle security system
ASCD CANCEL SW TYPE MODE1
TPMS WITH WITHOUT
Key Fob Type MODE6 MODE9
MODE6: Without panic alarm
MODE9: With panic alarm
AUTO SETTING ITEM
NOTE
Items Setting value
SELECTIVE UNLOCK SETTING WITHOUT
SELECTIVE UNLOCK WS WITHOUT
P/W UP/DOWN WITHOUT
P-POS WARN MODE1
ROOF FUNCTION W/O REQ SW
AUTO BACK DOOR WITHOUT
Trunk/Glass Hatch select Glass Hatch
Glass Hatch is indicated also for vehicles without a glass
hatch.
PANIC ALM TYPE MODE2
RAP FUNC SET MODE1
TR OPEN SW (INT) MODE1
DI LMP VARIAT MODE2
LIGHT RECOG MODE4
TRANSMISSION MT with ABS
RAIN SENSOR CONFIG WITHOUT
REAR WIPER WITH
H/L WASHER MODE3
HAZARD SW TYPE MODE1
BCM AC CONTROL MODE1
AUTO LOCK&UNLOCK FUNK WITHOUT
AUTO DOOR LOCK SELECT WITHOUT
AUTO DOOR UNLOCK SELECT WITHOUT
FOG ON WITH AUTO LIGHT WITH
MANUAL SETTING ITEM
NOTE
Items Setting value
AV C/U WITH WITHOUT
HANDLE LHD
THEFT ALM AREA WITHOUT MODE3
WITHOUT: Without vehicle security system
MODE3: With vehicle security system
ASCD CANCEL SW TYPE MODE2
BCS
INSPECTION AND ADJUSTMENT
BCS-101
< BASIC INSPECTION >
[FOR GENERAL AREAS]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
: Items which confirm vehicle specifications
LHD WITH M/T MODELS
: Items which confirm vehicle specifications
TPMS WITH WITHOUT
Key Fob Type MODE6 MODE9
MODE6: Without panic alarm
MODE9: With panic alarm
MANUAL SETTING ITEM
NOTE
Items Setting value
AUTO SETTING ITEM
NOTE
Items Setting value
SELECTIVE UNLOCK SETTING WITH
SELECTIVE UNLOCK WS WITH
P/W UP/DOWN MODE1
P-POS WARN MODE1
ROOF FUNCTION W/O REQ SW
AUTO BACK DOOR WITHOUT
Trunk/Glass Hatch select Glass Hatch
Glass Hatch is indicated also for vehicles without a glass
hatch.
PANIC ALM TYPE MODE2
RAP FUNC SET MODE1
TR OPEN SW (INT) MODE1
DI LMP VARIAT MODE2
LIGHT RECOG MODE4
TRANSMISSION AT with ABS
RAIN SENSOR CONFIG WITHOUT
REAR WIPER WITH
H/L WASHER MODE3
HAZARD SW TYPE MODE1
BCM AC CONTROL MODE1
AUTO LOCK&UNLOCK FUNK WITHOUT
AUTO DOOR LOCK SELECT WITHOUT
AUTO DOOR UNLOCK SELECT WITHOUT
FOG ON WITH AUTO LIGHT WITH
MANUAL SETTING ITEM
NOTE
Items Setting value
AV C/U WITH WITHOUT
HANDLE LHD
THEFT ALM AREA WITHOUT MODE3
WITHOUT: Without vehicle security system
MODE3: With vehicle security system
ASCD CANCEL SW TYPE MODE1
TPMS WITH WITHOUT
Key Fob Type MODE6 MODE9
MODE6: Without panic alarm
MODE9: With panic alarm
BCS-102
< BASIC INSPECTION >
[FOR GENERAL AREAS]
INSPECTION AND ADJUSTMENT
AUTO SETTING ITEM
NOTE
Items Setting value
SELECTIVE UNLOCK SETTING WITH
SELECTIVE UNLOCK WS WITH
P/W UP/DOWN MODE1
P-POS WARN MODE1
ROOF FUNCTION W/O REQ SW
AUTO BACK DOOR WITHOUT
Trunk/Glass Hatch select Glass Hatch
Glass Hatch is indicated also for vehicles without a glass
hatch.
PANIC ALM TYPE MODE2
RAP FUNC SET MODE1
TR OPEN SW (INT) MODE1
DI LMP VARIAT MODE2
LIGHT RECOG MODE4
TRANSMISSION MT with ABS
RAIN SENSOR CONFIG WITHOUT
REAR WIPER WITH
H/L WASHER MODE3
HAZARD SW TYPE MODE1
BCM AC CONTROL MODE1
AUTO LOCK&UNLOCK FUNK WITHOUT
AUTO DOOR LOCK SELECT WITHOUT
AUTO DOOR UNLOCK SELECT WITHOUT
FOG ON WITH AUTO LIGHT WITH
BCS
BODY CONTROL SYSTEM
BCS-103
< FUNCTION DIAGNOSIS >
[FOR GENERAL AREAS]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
FUNCTION DIAGNOSIS
BODY CONTROL SYSTEM
System Description INFOID:0000000004699657
OUTLINE
BCM (Body Control Module) controls the various electrical components. It inputs the information required to
the control from CAN communication and the signal received from each switch and sensor.
BCM has combination switch reading function for reading the operation status of combination switches (light,
turn signal, wiper and washer) in addition to a function for controlling the operation of various electrical com-
ponents. It also has the signal transmission function as the passed point of signal and the power saving con-
trol function that reduces the power consumption with the ignition switch OFF.
BCM is equipped with the diagnosis function that performs the diagnosis with CONSULT-III and various set-
tings.
BCM control function list
System Refer to
Combination switch reading system BCS-105, "System Diagram"
Signal buffer system BCS-109, "System Diagram"
Power consumption control system BCS-110, "System Diagram"
Auto light system EXL-263, "System Diagram"
Turn signal and hazard warning lamp system EXL-267, "System Diagram"
Headlamp system EXL-260, "System Diagram"
Parking, license plate and tail lamps system EXL-269, "System Diagram"
Rear fog lamp system EXL-271, "System Diagram"
Exterior lamp battery saver system EXL-273, "System Diagram"
Interior room lamp control system
INL-5, "System Diagram"
Luggage room lamp system
Interior room lamp battery saver system INL-8, "System Diagram"
Front wiper and washer system WW-161, "System Diagram"
Rear wiper and washer system WW-165, "System Diagram"
Headlamp washer system WW-168, "System Diagram"
Warning chime system WCS-13, "WARNING CHIME SYSTEM : System Diagram"
Door lock system DLK-574, "System Diagram"
Back door opener system DLK-606, "System Diagram"
Nissan Vehicle Immobilizer System (NVIS) - NATS SEC-18, "System Diagram"
Vehicle security system
SEC-32, "EXCEPT FOR EUROPE, SOUTH AFRICA, MIDDLE
EAST, RUSSIA AND UKRAINE : System Diagram"
Panic alarm
DLK-589, "REMOTE KEYLESS ENTRY FUNCTION : System
Description"
Rear window defogger system
DEF-103, "WITH NAVIGATION : System Diagram" (With NAVI)
DEF-105, "WITHOUT NAVIGATION : System Diagram" (With-
out NAVI)
BCS-104
< FUNCTION DIAGNOSIS >
[FOR GENERAL AREAS]
BODY CONTROL SYSTEM
Component Parts Location INFOID:0000000005047985
Intelligent Key system/engine start system
Door lock function
DLK-576, "INTELLIGENT KEY SYSTEM : System Diagram"
Back door open func-
tion
Remote keyless entry
function
Key reminder function
Warning function
Engine start function
Power window system PWC-187, "System Diagram"
Retained accessory power (RAP) system PWC-187, "System Description"
Tire pressure monitor system (TPMS) - AIR PRESSURE MONI-
TOR
WT-9, "System Diagram"
System Refer to
1. BCM
A. Dash side lower (passenger side)
JPMIA1345ZZ
BCS
COMBINATION SWITCH READING SYSTEM
BCS-105
< FUNCTION DIAGNOSIS >
[FOR GENERAL AREAS]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
COMBINATION SWITCH READING SYSTEM
System Diagram INFOID:0000000004699659
System Description INFOID:0000000004699660
OUTLINE
BCM reads the status of the combination switch (light, turn signal, wiper and washer) and recognizes the
status of each switch.
BCM is a combination of 5 output terminals (OUTPUT 1 - 5) and 5 input terminals (INPUT 1 - 5). It reads a
maximum of 20 switch status.
COMBINATION SWITCH MATRIX
Combination switch circuit
Combination switch INPUT-OUTPUT system list
JPMIA1494GB
System OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5
INPUT 1 FR WASHER FR WIPER LOW TURN LH TURN RH
INPUT 2 FR WIPER HI FR WIPER INT PASSING HEADLAMP 1
INPUT 3 INT VOLUME 1 RR WASHER HEADLAMP 2 HI BEAM
JPMIA1495GB
BCS-106
< FUNCTION DIAGNOSIS >
[FOR GENERAL AREAS]
COMBINATION SWITCH READING SYSTEM
NOTE:
Headlamp has a dual system switch.
COMBINATION SWITCH READING FUNCTION
Description
BCM reads the status of the combination switch at 10 ms interval normally.
NOTE:
BCM reads the status of the combination switch at 60 ms interval when BCM is controlled at low power con-
sumption mode.
BCM operates as follows and judges the status of the combination switch.
- INPUT 1 - 5 outputs the voltage waveforms of 5 systems simultaneously.
- It operates the transistor on OUTPUT side in the following order: OUTPUT 5 4 3 2 1.
- The voltage waveform of INPUT corresponding to the formed circuit changes according to the operation of
the transistor on OUTPUT side if any (1 or more) switches are ON.
- It reads this change of the voltage as the status signal of the combination switch.
Operation Example
In the following operation example, the combination of the status signals of the combination switch is replaced
as follows: INPUT 1 - 5 to 1 - 5 and OUTPUT 1 - 5 to A - E.
Example 1: When a switch (TURN RH switch) is turned ON
INPUT 4 RR WIPER INT INT VOLUME 3 AUTO LIGHT TAIL LAMP
INPUT 5 INT VOLUME 2 RR WIPER ON RR FOG
System OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5
JPMIA0067GB
JPMIA0068GB
BCS
COMBINATION SWITCH READING SYSTEM
BCS-107
< FUNCTION DIAGNOSIS >
[FOR GENERAL AREAS]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
The circuit between INPUT 1 and OUTPUT 5 is formed when the TURN RH switch is turned ON.
BCM detects the combination switch status signal 1E when the signal of OUTPUT 5 is input to INPUT 1.
BCM judges that the TURN RH switch is ON when the signal 1E is detected.
Example 2: When some switches (turn RH switch, front wiper LO switch) are turned ON
The circuits between INPUT 1 and OUTPUT 5 and between INPUT 1 and OUTPUT 3 are formed when the
TURN RH switch and FR WIPER LOW switch are turned ON.
BCM detects the combination switch status signal 1CE when the signals of OUTPUT 3 and OUTPUT 5 are
input to INPUT 1.
BCM judges that the TURN RH switch and FR WIPER LOW switch are ON when the signal 1CE is
detected.
WIPER VOLUME DIAL POSITION
BCM judges the wiper intermittent dial 1 - 7 by the status of INT VOLUME 1, 2 and 3 switches.
JPMIA1496GB
JPMIA1497GB
Wiper intermittent dial position
Switch status
INT VOLUME 1 INT VOLUME 2 INT VOLUME 3
1 ON ON ON
2 ON ON OFF
3 ON OFF OFF
4 OFF OFF OFF
5 OFF OFF ON
BCS-108
< FUNCTION DIAGNOSIS >
[FOR GENERAL AREAS]
COMBINATION SWITCH READING SYSTEM
NOTE:
For details of wiper intermittent dial position, refer to WW-161, "System Description".
6 OFF ON ON
7 OFF ON OFF
Wiper intermittent dial position
Switch status
INT VOLUME 1 INT VOLUME 2 INT VOLUME 3
BCS
SIGNAL BUFFER SYSTEM
BCS-109
< FUNCTION DIAGNOSIS >
[FOR GENERAL AREAS]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
SIGNAL BUFFER SYSTEM
System Diagram INFOID:0000000005047975
System Description INFOID:0000000005047976
OUTLINE
BCM has the signal transmission function that outputs/transmits each input/received signal to each unit.
Signal transmission function list
JPMIA1014GB
Signal name Input Output Description
Ignition switch ON signal
Push-button ignition switch
(Push switch)
IPDM E/R (CAN)
Inputs the push-button ignition
switch (push switch) signal and
transmits the ignition switch sta-
tus judged with BCM via CAN
communication.
Door switch signal Any door switch
Combination meter (CAN)
IPDM E/R (CAN)
Inputs the door switch signal
and transmits it via CAN com-
munication.
Oil pressure switch signal IPDM E/R (CAN) Combination meter (CAN)
Transmits the received oil pres-
sure switch signal via CAN
communication.
Stop lamp switch signal Stop lamp switch TCM (CAN)
Inputs the stop lamp switch 1
signal and stop lamp switch 2
signal, and transmits the stop
lamp switch signal via CAN
communication.
BCS-110
< FUNCTION DIAGNOSIS >
[FOR GENERAL AREAS]
POWER CONSUMPTION CONTROL SYSTEM
POWER CONSUMPTION CONTROL SYSTEM
System Diagram INFOID:0000000005047980
System Description INFOID:0000000004699664
OUTLINE
BCM incorporates a power saving control function that reduces the power consumption according to the
vehicle status.
BCM switches the status (control mode) by itself with the power saving control function. It performs the sleep
request to each unit (IPDM E/R and combination meter) that operates with the ignition switch OFF.
Normal mode (wake-up)
- CAN communication is normally performed with other units
- Each control with BCM is operating properly
CAN communication sleep mode (CAN sleep)
- CAN transmission is stopped
- Control with BCM only is operating
Low power consumption mode (BCM sleep)
- Low power consumption control is active
- CAN transmission is stopped
LOW POWER CONSUMPTION CONTROL WITH BCM
BCM reduces the power consumption with the following operation in the low power consumption mode.
The reading interval of the each switches changes from 10 ms interval to 60 ms interval.
Sleep mode activation
BCM receives the sleep-ready signal (ready) from IPDM E/R and combination meter via CAN communica-
tion.
BCM transmits the sleep wake up signal (sleep) to each unit when all of the CAN sleep conditions are ful-
filled.
Each unit stops the transmission of CAN communication with the sleep wake up signal. BCM is in CAN com-
munication sleep mode.
BCM is in the low power consumption mode and perform the low power consumption control when all of the
BCM sleep conditions are fulfilled with CAN sleep condition.
JSMIA0050GB
BCS
POWER CONSUMPTION CONTROL SYSTEM
BCS-111
< FUNCTION DIAGNOSIS >
[FOR GENERAL AREAS]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
Sleep condition
Wake-up operation
BCM changes from the low power consumption mode to the CAN communication sleep mode when the any
of the BCM wake-up conditions is fulfilled. Only the control with BCM is activated.
BCM transmits the sleep wake up signal (wake up) to each unit when any of the CAN wake-up conditions is
fulfilled. It changes from the low power consumption mode or the CAN communication sleep mode to the
normal mode.
Each unit starts the transmission of CAN communication with the sleep wake up signal. In addition, the com-
bination meter transmits the wake up signal to BCM via CAN communication to report the CAN communica-
tion start.
Wake-up condition
CAN sleep condition BCM sleep condition
Receiving the sleep-ready signal (ready) from all units
Ignition switch: OFF
Vehicle security system and panic alarm: Not operation
Warning chime: Not operation
Intelligent Key system buzzer: Not operation
Stop lamp switch: OFF
Key slot (card switch) status: No change
Turn signal indicator lamp: Not operation
Exterior lamp: OFF
Door lock status: No change
CONSULT-III communication status: Not communication
Meter display signal: Non-transmission
Door switch status: No change
Rear window defogger: OFF
Interior room lamp battery saver: Time out
RAP system: OFF
Power window switch communication: No transmission
Push-button ignition switch illumination: OFF
Nissan Vehicle Immobilizer System (NVIS) - NATS: Not opera-
tion
Remote keyless entry receiver communication status: No com-
munication
Tire pressure monitor system (TPMS) - AIR PRESSURE MON-
ITOR: Stop
LOCK indicator lamp: OFF
ACC indicator lamp: OFF
ON indicator lamp: OFF
BCM wake-up condition CAN wake-up condition
Power window switch communication: Receiving
Remote keyless entry receiver: Receiving
Receiving the sleep-ready signal (Not-ready) from any units
Key slot (key switch): OFF ON, ON OFF
Push-button ignition switch (push switch): OFF ON
Hazard switch: OFF ON
PASSING switch: OFF ON, ON OFF
TAIL LAMP switch: OFF ON
RR FOG switch: OFF ON
Driver door switch: OFF ON, ON OFF
Passenger door switch: OFF ON, ON OFF
Back door switch: OFF ON, ON OFF
Driver door request switch: OFF ON
Passenger door request switch: OFF ON
Back door request switch: OFF ON
Stop lamp switch: ON
Clutch interlock switch: OFF ON
BCS-112
< FUNCTION DIAGNOSIS >
[FOR GENERAL AREAS]
POWER CONSUMPTION CONTROL SYSTEM
Component Parts Location INFOID:0000000004699665
1. Combination meter 2. BCM
Refer to BCS-104, "Component
Parts Location".
3. IPDM E/R
Refer to PCS-6, "Component Parts
Location".
JPMIA1346ZZ
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-113
< FUNCTION DIAGNOSIS >
[FOR GENERAL AREAS]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM) INFOID:0000000005047981
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
: Applicable item
NOTE:
*1: At models with light and rain sensor or rain sensor this mode is displayed, but is not used.
*2: This item is displayed, but is not used.
*3: At models without RAP system this mode is displayed, but is not used.
Diagnosis mode Function Description
Work Support Changes the setting for each system function.
Self Diagnostic Result Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM. Refer to CONSULT-III opera-
tion manual.
Data Monitor The BCM input/output signals are displayed.
Active Test The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification The BCM part number is displayed.
Configuration
Read and save the vehicle specification.
Write the vehicle specification when replacing BCM.
System Sub system selection item
Diagnosis mode
Work Support Data Monitor Active Test
Door lock DOOR LOCK
Rear window defogger REAR DEFOGGER
Warning chime BUZZER
Interior room lamp timer INT LAMP
Exterior lamp HEAD LAMP
Wiper and washer WIPER
*
1
Turn signal and hazard warning lamps FLASHER
AIR CONDITONER*
2
Intelligent Key system
Engine start system
INTELLIGENT KEY
Combination switch COMB SW
Body control system BCM
NVIS - NATS IMMU
Interior room lamp battery saver BATTERY SAVER
Trunk lid open TRUNK
Vehicle security system THEFT ALM
RAP system
RETAINED PWR*
3
AIR CONDITONER*
2
Intelligent Key system
Engine start system
INTELLIGENT KEY
Combination switch COMB SW
Body control system BCM
NVIS - NATS IMMU
Interior room lamp battery saver BATTERY SAVER
Trunk lid open TRUNK
Vehicle security system THEFT ALM
RAP system
RETAINED PWR*
3
CONFRM ID ALL
The key ID that the key slot receives is not recognized by any key ID registered
to BCM.
Yet
The key ID that the key slot receives is recognized by any key ID registered to
BCM.
Done
Monitor Item Condition Value/Status
BCS-234
< ECU DIAGNOSIS >
[FOR SOUTH AFRICA]
BCM (BODY CONTROL MODULE)
CONFIRM ID4
The key ID that the key slot receives is not recognized by the fourth key ID regis-
tered to BCM.
Yet
The key ID that the key slot receives is recognized by the fourth key ID registered
to BCM.
Done
CONFIRM ID3
The key ID that the key slot receives is not recognized by the third key ID regis-
tered to BCM.
Yet
The key ID that the key slot receives is recognized by the third key ID registered
to BCM.
Done
CONFIRM ID2
The key ID that the key slot receives is not recognized by the second key ID reg-
istered to BCM.
Yet
The key ID that the key slot receives is recognized by the second key ID regis-
tered to BCM.
Done
CONFIRM ID1
The key ID that the key slot receives is not recognized by the first key ID regis-
tered to BCM.
Yet
The key ID that the key slot receives is recognized by the first key ID registered
to BCM.
Done
TP 4
The ID of fourth Intelligent Key is not registered to BCM Yet
The ID of fourth Intelligent Key is registered to BCM Done
TP 3
The ID of third Intelligent Key is not registered to BCM Yet
The ID of third Intelligent Key is registered to BCM Done
TP 2
The ID of second Intelligent Key is not registered to BCM Yet
The ID of second Intelligent Key is registered to BCM Done
TP 1
The ID of first Intelligent Key is not registered to BCM Yet
The ID of first Intelligent Key is registered to BCM Done
AIR PRESS FL Ignition switch ON (Only when the signal from the transmitter is received)
Air pressure of front LH
tire
AIR PRESS FR Ignition switch ON (Only when the signal from the transmitter is received)
Air pressure of front RH
tire
AIR PRESS RR Ignition switch ON (Only when the signal from the transmitter is received)
Air pressure of rear RH
tire
AIR PRESS RL Ignition switch ON (Only when the signal from the transmitter is received)
Air pressure of rear LH
tire
ID REGST FL1
ID of front LH tire transmitter is registered Done
ID of front LH tire transmitter is not registered Yet
ID REGST FR1
ID of front RH tire transmitter is registered Done
ID of front RH tire transmitter is not registered Yet
ID REGST RR1
ID of rear RH tire transmitter is registered Done
ID of rear RH tire transmitter is not registered Yet
ID REGST RL1
ID of rear LH tire transmitter is registered Done
ID of rear LH tire transmitter is not registered Yet
WARNING LAMP
Tire pressure indicator OFF Off
Tire pressure indicator ON On
BUZZER
Tire pressure warning alarm is not sounding Off
Tire pressure warning alarm is sounding On
Monitor Item Condition Value/Status
BCS
BCM (BODY CONTROL MODULE)
BCS-235
< ECU DIAGNOSIS >
[FOR SOUTH AFRICA]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
TERMINAL LAYOUT
PHYSICAL VALUES
JPMIA0062ZZ
BCS-236
< ECU DIAGNOSIS >
[FOR SOUTH AFRICA]
BCM (BODY CONTROL MODULE)
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output +
1
(W)
Ground Battery power supply Input Ignition switch OFF Battery voltage
2
(Y)
Ground
P/W power supply
(BAT)
Output Ignition switch OFF 12 V
3
(P)
Ground
P/W power supply
(IGN)
Output Ignition switch ON 12 V
4
(R)
Ground
Interior room lamp
power supply
Output
Interior room lamp battery saver is activated.
(Cuts the interior room lamp power supply)
0 V
Interior room lamp battery saver is not acti-
vated.
(Outputs the interior room lamp power sup-
ply)
12 V
8
(L)
Ground
All doors, fuel lid
LOCK
Output
All doors, fuel
lid
LOCK
(Actuator is activated)
12 V
Other than LOCK
(Actuator is not activated)
0 V
9
(G)
Ground
All doors, fuel lid UN-
LOCK
Output
Driver door,
fuel lid
UNLOCK
(Actuator is activated)
12 V
Other than UNLOCK
(Actuator is not activated)
0 V
11
(O)
Ground Battery power supply Input Ignition switch OFF Battery voltage
13
(B)
Ground Ground Ignition switch ON 0 V
15
(Y)
Ground ACC indicator lamp Output Ignition switch
OFF (LOCK indicator is
not illuminated)
Battery voltage
ACC 0 V
17
(V)
Ground
Turn signal RH (Front
and side)
Output
Ignition switch
ON
Turn signal switch OFF 0 V
Turn signal switch RH
6.5 V
18
(LG)
Ground
Turn signal LH (Front
and side)
Output
Ignition switch
ON
Turn signal switch OFF 0 V
Turn signal switch LH
6.5 V
19
(SB)
Ground
Room lamp timer
control
Output
Interior room
lamp
OFF 12 V
ON 0 V
PKID0926E
PKID0926E
BCS
BCM (BODY CONTROL MODULE)
BCS-237
< ECU DIAGNOSIS >
[FOR SOUTH AFRICA]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
20
(V)
Ground Turn signal RH (Rear) Output
Ignition switch
ON
Turn signal switch OFF 0 V
Turn signal switch RH
6.5 V
23
(L)
Ground Back door open Output Back door
OPEN
(Back door opener actua-
tor is activated)
12 V
Other than OPEN
(Back door opener actua-
tor is not activated)
0 V
24
(O)
Ground Rear fog lamp Output Rear fog lamp
OFF 0 V
ON 12 V
25
(BR)
Ground Turn signal LH (Rear) Output
Ignition switch
ON
Turn signal switch OFF 0 V
Turn signal switch LH
6.5 V
26
(G)
Ground Rear wiper Output Rear wiper
OFF (Stopped) 0 V
ON (Operated) 12 V
30
(P)
Ground Luggage room lamp Output
Luggage room
lamp
ON 0 V
OFF 12 V
34
(L)
Ground
Luggage room anten-
na ()
Output
Ignition switch
OFF
When Intelligent Key is in
the passenger compart-
ment
When Intelligent Key is not
in the passenger compart-
ment
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output +
PKID0926E
PKID0926E
JMKIA0062GB
JMKIA0063GB
BCS-238
< ECU DIAGNOSIS >
[FOR SOUTH AFRICA]
BCM (BODY CONTROL MODULE)
35
(R)
Ground
Luggage room anten-
na (+)
Output
Ignition switch
OFF
When Intelligent Key is in
the passenger compart-
ment
When Intelligent Key is not
in the passenger compart-
ment
38
(B)
Ground
Rear bumper anten-
na ()
Output
When the back
door request
switch is oper-
ated with igni-
tion switch
OFF
When Intelligent Key is in
the antenna detection
area
When Intelligent Key is not
in the antenna detection
area
39
(W)
Ground
Rear bumper anten-
na (+)
Output
When the back
door request
switch is oper-
ated with igni-
tion switch
OFF
When Intelligent Key is in
the antenna detection
area
When Intelligent Key is not
in the antenna detection
area
47
(SB)
Ground
Ignition relay (IPDM
E/R) control
Output Ignition switch
OFF or ACC 12 V
ON 0 V
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output +
JMKIA0062GB
JMKIA0063GB
JMKIA0062GB
JMKIA0063GB
JMKIA0062GB
JMKIA0063GB
BCS
BCM (BODY CONTROL MODULE)
BCS-239
< ECU DIAGNOSIS >
[FOR SOUTH AFRICA]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
52
(P)
Ground Starter relay control Output
Ignition switch
ON (A/T mod-
els)
When selector lever is in P
or N position
12 V
When selector lever is not
in P or N position
0 V
Ignition switch ON (M/T models) Battery voltage
61
(BR)
Ground
Back door request
switch
Input
Back door re-
quest switch
ON (Pressed) 0 V
OFF (Not pressed)
1.0 V
64
(V)
Ground
Intelligent Key warn-
ing buzzer
Output
Intelligent Key
warning buzzer
Sounding 0 V
Not sounding 12 V
65
(O)
Ground
Rear wiper stop posi-
tion
Input Rear wiper
In stop position
1.0 V
Not in stop position 0 V
66
(R)
Ground Back door switch Input
Back door
switch
OFF (When back door
closes)
11.8 V
ON (When back door
opens)
0 V
67
(GR)
Ground
Back door opener
switch
Input
Back door
opener switch
Pressed 0 V
Not pressed
11.8 V
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output +
JPMIA0016GB
JPMIA0016GB
JPMIA0011GB
JPMIA0011GB
BCS-240
< ECU DIAGNOSIS >
[FOR SOUTH AFRICA]
BCM (BODY CONTROL MODULE)
72
(R)
Ground
Room antenna ()
(Center console)
Output
Ignition switch
OFF
When Intelligent Key is in
the passenger compart-
ment
When Intelligent Key is not
in the passenger compart-
ment
73
(G)
Ground
Room antenna (+)
(Center console)
Output
Ignition switch
OFF
When Intelligent Key is in
the passenger compart-
ment
When Intelligent Key is not
in the passenger compart-
ment
74
(SB)
Ground
Passenger door an-
tenna ()
Output
When the pas-
senger door re-
quest switch is
operated with
ignition switch
OFF
When Intelligent Key is in
the antenna detection
area
When Intelligent Key is not
in the antenna detection
area
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output +
JMKIA0062GB
JMKIA0063GB
JMKIA0062GB
JMKIA0063GB
JMKIA0062GB
JMKIA0063GB
BCS
BCM (BODY CONTROL MODULE)
BCS-241
< ECU DIAGNOSIS >
[FOR SOUTH AFRICA]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
75
(BR)
Ground
Passenger door an-
tenna (+)
Output
When the pas-
senger door re-
quest switch is
operated with
ignition switch
OFF
When Intelligent Key is in
the antenna detection
area
When Intelligent Key is not
in the antenna detection
area
76
(V)
Ground
Driver door antenna
()
Output
When the driv-
er door request
switch is oper-
ated with igni-
tion switch
OFF
When Intelligent Key is in
the antenna detection
area
When Intelligent Key is not
in the antenna detection
area
77
(LG)
Ground
Driver door antenna
(+)
Output
When the driv-
er door request
switch is oper-
ated with igni-
tion switch
OFF
When Intelligent Key is in
the antenna detection
area
When Intelligent Key is not
in the antenna detection
area
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output +
JMKIA0062GB
JMKIA0063GB
JMKIA0062GB
JMKIA0063GB
JMKIA0062GB
JMKIA0063GB
BCS-242
< ECU DIAGNOSIS >
[FOR SOUTH AFRICA]
BCM (BODY CONTROL MODULE)
80
(GR)
Ground
NATS antenna amp
(Built in key slot)
Input/
Output
During waiting
Ignition switch is pressed
while inserting the Intelli-
gent Key into the key slot.
Just after pressing ignition
switch. Pointer of tester should
move.
81
(W)
Ground
NATS antenna amp
(Built in key slot)
Input/
Output
During waiting
Ignition switch is pressed
while inserting the Intelli-
gent Key into the key slot.
Just after pressing ignition
switch. Pointer of tester should
move.
82
(R)
Ground
Ignition relay [Fuse
block (J/B)] control
Output Ignition switch
OFF or ACC 0 V
ON 12 V
83
(Y)
Ground
Remote keyless entry
receiver communica-
tion
Input/
Output
During waiting
When operating either button on the Intelli-
gent Key
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output +
JMKIA0064GB
JMKIA0065GB
BCS
BCM (BODY CONTROL MODULE)
BCS-243
< ECU DIAGNOSIS >
[FOR SOUTH AFRICA]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
87
(BR)
Ground
Combination switch
INPUT 5
Input
Combination
switch
All switches OFF
(Wiper volume dial 4)
1.4 V
Rear fog lamp switch ON
(Wiper volume dial 4)
1.3 V
Rear wiper switch ON
(Wiper volume dial 4)
1.3 V
Any of the conditions be-
low with all switches OFF
Wiper volume dial 1
Wiper volume dial 2
Wiper volume dial 6
Wiper volume dial 7
1.3 V
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output +
JPMIA0041GB
JPMIA0038GB
JPMIA0039GB
JPMIA0040GB
BCS-244
< ECU DIAGNOSIS >
[FOR SOUTH AFRICA]
BCM (BODY CONTROL MODULE)
88
(V)
Ground
Combination switch
INPUT 3
Input
Combination
switch
All switches OFF
(Wiper volume dial 4)
1.4 V
Lighting switch HI
(Wiper volume dial 4)
1.3 V
Lighting switch 2ND
(Wiper volume dial 4)
1.3 V
Rear washer switch ON
(Wiper volume dial 4)
1.3 V
Any of the conditions be-
low with all switches OFF
Wiper volume dial 1
Wiper volume dial 2
Wiper volume dial 3
1.3 V
89
(BR)
Ground
Push-button ignition
switch (Push switch)
Input
Push-button ig-
nition switch
(push switch)
Pressed 0 V
Not pressed Battery voltage
90
(P)
Ground CAN-L
Input/
Output
91
(L)
Ground CAN-H
Input/
Output
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output +
JPMIA0041GB
JPMIA0036GB
JPMIA0037GB
JPMIA0039GB
JPMIA0040GB
BCS
BCM (BODY CONTROL MODULE)
BCS-245
< ECU DIAGNOSIS >
[FOR SOUTH AFRICA]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
92
(LG)
Ground Key slot illumination Output
Key slot illumi-
nation
OFF 12 V
Blinking
6.5 V
ON 0 V
93
(V)
Ground ON indicator lamp Output Ignition switch
OFF (LOCK indicator is
not illuminated)
Battery voltage
ON or ACC 0 V
95
(O)
Ground ACC relay control Output Ignition switch
OFF 0 V
ACC or ON 12 V
96*
1
(Y)
Ground
Control device (De-
tention switch) power
supply
Output 12 V
97
(L)
Ground
Steering lock condi-
tion No. 1
Input Steering lock
LOCK status 0 V
UNLOCK status 12 V
98
(P)
Ground
Steering lock condi-
tion No. 2
Input Steering lock
LOCK status 12 V
UNLOCK status 0 V
99*
1
(O)
Ground
Selector lever P posi-
tion switch
Input Selector lever
P position 0 V
Any position other than P 12 V
100
(G)
Ground
Passenger door re-
quest switch
Input
Passenger
door request
switch
ON (Pressed) 0 V
OFF (Not pressed)
1.0 V
101
(SB)
Ground
Driver door request
switch
Input
Driver door re-
quest switch
ON (Pressed) 0 V
OFF (Not pressed)
1.0 V
102
(O)
Ground
Blower fan motor re-
lay control
Output Ignition switch
OFF or ACC 0 V
ON 12 V
103
(LG)
Ground
Remote keyless entry
receiver power sup-
ply
Output Ignition switch OFF 12 V
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output +
JPMIA0015GB
JPMIA0016GB
JPMIA0016GB
BCS-246
< ECU DIAGNOSIS >
[FOR SOUTH AFRICA]
BCM (BODY CONTROL MODULE)
106
(W)
Ground
Steering lock unit
power supply
Output Ignition switch
OFF or ACC 12 V
ON 0 V
107
(LG)
Ground
Combination switch
INPUT 1
Input
Combination
switch
(Wiper volume
dial 4)
All switches OFF
1.4 V
Turn signal switch LH
1.3 V
Turn signal switch RH
1.3 V
Front wiper switch LO
1.3 V
Front washer switch ON
1.3 V
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output +
JPMIA0041GB
JPMIA0037GB
JPMIA0036GB
JPMIA0038GB
JPMIA0039GB
BCS
BCM (BODY CONTROL MODULE)
BCS-247
< ECU DIAGNOSIS >
[FOR SOUTH AFRICA]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
108
(R)
Ground
Combination switch
INPUT 4
Input
Combination
switch
All switches OFF
(Wiper volume dial 4)
1.4 V
Lighting switch AUTO
(Wiper volume dial 4)
1.3 V
Lighting switch 1ST
(Wiper volume dial 4)
1.3 V
Rear wiper switch INT
(Wiper volume dial 4)
1.3 V
Any of the conditions be-
low with all switches OFF
Wiper volume dial 1
Wiper volume dial 5
Wiper volume dial 6
1.3 V
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output +
JPMIA0041GB
JPMIA0038GB
JPMIA0036GB
JPMIA0040GB
JPMIA0039GB
BCS-248
< ECU DIAGNOSIS >
[FOR SOUTH AFRICA]
BCM (BODY CONTROL MODULE)
109
(Y)
Ground
Combination switch
INPUT 2
Input
Combination
switch
(Wiper volume
dial 4)
All switches OFF
1.4 V
Lighting switch PASS
1.3 V
Lighting switch 2ND
1.3 V
Front wiper switch AUTO
1.3 V
Front wiper switch HI
1.3 V
110
(G)
Ground Hazard switch Input Hazard switch
ON 0 V
OFF
1.1 V
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output +
JPMIA0041GB
JPMIA0037GB
JPMIA0036GB
JPMIA0038GB
JPMIA0040GB
JPMIA0012GB
BCS
BCM (BODY CONTROL MODULE)
BCS-249
< ECU DIAGNOSIS >
[FOR SOUTH AFRICA]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
111
(Y)
Ground
Steering lock unit
communication
Input/
Output
Steering lock
LOCK status 12 V
LOCK or UNLOCK
For 15 seconds after UN-
LOCK
12 V
15 seconds or later after
UNLOCK
0 V
112
(R)
Ground
Rain sensor serial
link
Input/
Output
Ignition switch ON
8.7 V
113
(P)
Ground Optical sensor Input
Ignition switch
ON
When bright outside of the
vehicle
Close to 5 V
When dark outside of the
vehicle
Close to 0 V
114*
2
(O)
Ground
Clutch interlock
switch
Input
Clutch interlock
switch
OFF (Clutch pedal is not
depressed)
0 V
ON (Clutch pedal is de-
pressed)
Battery voltage
116
(SB)
Ground Stop lamp switch 1 Input Battery voltage
118
(P)
Ground Stop lamp switch 2 Input
Stop lamp
switch
OFF (Brake pedal is not
depressed)
0 V
ON (Brake pedal is de-
pressed)
Battery voltage
119
(BR)
Ground
Driver side door lock
assembly (Unlock
sensor)
Input Driver door
LOCK status
(Unlock sensor switch
OFF)
1.1 V
UNLOCK status
(Unlock switch sensor
ON)
0 V
121
(R)
Ground Key slot switch Input
When the Intelligent Key is inserted into key
slot
12 V
When the Intelligent Key is not inserted into
key slot
0 V
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output +
JMKIA0066GB
JPMIA0156GB
JPMIA0012GB
BCS-250
< ECU DIAGNOSIS >
[FOR SOUTH AFRICA]
BCM (BODY CONTROL MODULE)
123
(W)
Ground IGN feedback Input Ignition switch
OFF or ACC 0 V
ON Battery voltage
124
(LG)
Ground
Passenger door
switch
Input
Passenger
door switch
OFF (Door close)
11.8 V
ON (Door open) 0 V
130*
3
(L)
Ground
Rear window defog-
ger switch
Input
Ignition switch
ON
Rear window defogger
switch OFF
1.1 V
Rear window defogger
switch ON
0 V
132
(V)
Ground
Power window switch
communication
Input/
Output
Ignition switch ON
10.2 V
Ignition switch OFF or ACC 12 V
133
(R)
Ground
Push-button ignition
switch illumination
Output
Push-button ig-
nition switch il-
lumination
ON (Tail lamps OFF) 9.5 V
ON (Tail lamps ON)
NOTE:
The pulse width of this wave is
varied by the illumination bright-
ening/dimming level.
OFF 0 V
134
(W)
Ground LOCK indicator lamp Output
LOCK indicator
lamp
OFF Battery voltage
ON 0 V
137
(O)
Ground
Receiver and sensor
ground
Input Ignition switch ON 0 V
138
(Y)
Ground
Receiver and sensor
power supply
Output Ignition switch
OFF 0 V
ACC or ON 5.0 V
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output +
JPMIA0011GB
JPMIA0012GB
JPMIA0013GB
JPMIA0159GB
BCS
BCM (BODY CONTROL MODULE)
BCS-251
< ECU DIAGNOSIS >
[FOR SOUTH AFRICA]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
140
(LG)*
4
(G)*
5
Ground
Selector lever P/N
position (A/T models)
Input
Selector lever
P or N position 12 V
Except P and N positions 0 V
Park/neutral position
switch (M/T models)
Ignition switch
ON
Control lever in neutral po-
sition
Battery voltage
Control lever in any posi-
tion other than neutral
0
141
(G)
Ground Security indicator Output
Security indica-
tor
ON 0 V
Blinking
11.3 V
OFF 12 V
142
(O)
Ground
Combination switch
OUTPUT 5
Output
Combination
switch
(Wiper volume
dial 4)
All switches OFF 0 V
Lighting switch 1ST
10.7 V
Lighting switch HI
Lighting switch 2ND
Turn signal switch RH
143
(P)
Ground
Combination switch
OUTPUT 1
Output
Combination
switch
All switches OFF
(Wiper volume dial 4)
0 V
Front wiper switch HI
(Wiper volume dial 4)
10.7 V
Rear wiper switch INT
(Wiper volume dial 4)
Any of the conditions be-
low with all switches OFF
Wiper volume dial 1
Wiper volume dial 2
Wiper volume dial 3
Wiper volume dial 6
Wiper volume dial 7
144
(GR)
Ground
Combination switch
OUTPUT 2
Output
Combination
switch
All switches OFF
(Wiper volume dial 4)
0 V
Front washer switch ON
(Wiper volume dial 4)
10.7 V
Rear wiper switch ON
(Wiper volume dial 4)
Rear washer switch ON
(Wiper volume dial 4)
Any of the conditions be-
low with all switches OFF
Wiper volume dial 1
Wiper volume dial 5
Wiper volume dial 6
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output +
JPMIA0014GB
JPMIA0031GB
JPMIA0032GB
JPMIA0033GB
BCS-252
< ECU DIAGNOSIS >
[FOR SOUTH AFRICA]
BCM (BODY CONTROL MODULE)
*1: Only A/T models
*2: Only M/T models
*3: Without NAVI
*4: A/T models
*5: M/T models
145
(L)
Ground
Combination switch
OUTPUT 3
Output
Combination
switch
(Wiper volume
dial 4)
All switches OFF 0 V
Front wiper switch AUTO
10.7 V
Front wiper switch LO
Lighting switch AUTO
Rear fog lamp switch ON
146
(SB)
Ground
Combination switch
OUTPUT 4
Output
Combination
switch
(Wiper volume
dial 4)
All switches OFF 0 V
Lighting switch 2ND
10.7 V
Lighting switch PASS
Turn signal switch LH
150
(GR)
Ground Driver door switch Input
Driver door
switch
OFF (Door close)
11.8 V
ON (Door open) 0 V
151
(G)
Ground
Rear window defog-
ger relay control
Output
Rear window
defogger
Active 0 V
Not activated Battery voltage
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output +
JPMIA0034GB
JPMIA0035GB
JPMIA0011GB
BCS
BCM (BODY CONTROL MODULE)
BCS-253
< ECU DIAGNOSIS >
[FOR SOUTH AFRICA]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
Wiring Diagram - BCM - INFOID:0000000005000989
JCMWM3738GB
BCS-254
< ECU DIAGNOSIS >
[FOR SOUTH AFRICA]
BCM (BODY CONTROL MODULE)
JCMWM3739GB
BCS
BCM (BODY CONTROL MODULE)
BCS-255
< ECU DIAGNOSIS >
[FOR SOUTH AFRICA]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
JCMWM3740GB
BCS-256
< ECU DIAGNOSIS >
[FOR SOUTH AFRICA]
BCM (BODY CONTROL MODULE)
JCMWM3741GB
BCS
BCM (BODY CONTROL MODULE)
BCS-257
< ECU DIAGNOSIS >
[FOR SOUTH AFRICA]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
JCMWM3742GB
BCS-258
< ECU DIAGNOSIS >
[FOR SOUTH AFRICA]
BCM (BODY CONTROL MODULE)
Fail-safe INFOID:0000000005000937
FAIL-SAFE CONTROL BY DTC
BCM performs fail-safe control when any DTC are detected.
JCMWM3743GB
BCS
BCM (BODY CONTROL MODULE)
BCS-259
< ECU DIAGNOSIS >
[FOR SOUTH AFRICA]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
Display contents of CONSULT Fail-safe Cancellation
B2013: ID DISCORD BCM-S/L Inhibit engine cranking Erase DTC
B2014: CHAIN OF S/L-BCM Inhibit engine cranking Erase DTC
B2190: NATS ANTENNA AMP Inhibit engine cranking Erase DTC
B2191: DIFFERENCE OF KEY Inhibit engine cranking Erase DTC
B2192: ID DISCORD BCM-ECM Inhibit engine cranking Erase DTC
B2193: CHAIN OF BCM-ECM Inhibit engine cranking Erase DTC
B2195: ANTI SCANNING Inhibit engine cranking Ignition switch ON OFF
B2557: VEHICLE SPEED Inhibit steering lock
When normal vehicle speed signals are received from ABS actua-
tor and electric unit (control unit) for 500 ms
B2560: STARTER CONT RELAY Inhibit engine cranking
500 ms after the following CAN signal communication status be-
comes consistent
Starter control relay signal
Starter relay status signal
B2601: SHIFT POSITION Inhibit steering lock
500 ms after the following signal reception status becomes consis-
tent
Selector lever P position switch signal
P range signal (CAN)
B2602: SHIFT POSITION Inhibit steering lock
5 seconds after the following BCM recognition conditions are ful-
filled
Ignition switch is in the ON position
Selector lever P position switch signal: Except P position (battery
voltage)
Vehicle speed: 4 km/h (2.5 MPH) or more
B2603: SHIFT POSI STATUS Inhibit steering lock
500 ms after the following BCM recognition conditions are fulfilled
Ignition switch is in the ON position
Selector lever P position switch signal: Except P position (battery
voltage)
Selector lever P/N position signal: Except P and N positions (0 V)
B2604: PNP SW Inhibit steering lock
500 ms after any of the following BCM recognition conditions are
fulfilled
Status 1
- Ignition switch is in the ON position
- Selector lever P/N position signal: P and N position (battery volt-
age)
- P range signal or N range signal (CAN): ON
Status 2
- Ignition switch is in the ON position
- Selector lever P/N position signal: Except P and N positions (0 V)
- P range signal and N range signal (CAN): OFF
B2605: PNP SW Inhibit steering lock
500 ms after any of the following BCM recognition conditions are
fulfilled
Status 1
- Ignition switch is in the ON position
- Selector lever P/N position signal: Except P and N positions (0 V)
- Interlock/PNP switch signal (CAN): OFF
Status 2
- Ignition switch is in the ON position
- Selector lever P/N position signal: P or N position (battery volt-
age)
- PNP switch signal (CAN): ON
B2606: S/L RELAY Inhibit engine cranking
500 ms after the following CAN signal communication status be-
comes consistent
Steering lock relay signal (Request signal)
Steering lock relay signal (Condition signal)
BCS-260
< ECU DIAGNOSIS >
[FOR SOUTH AFRICA]
BCM (BODY CONTROL MODULE)
HIGH FLASHER OPERATION
BCM detects the turn signal lamp circuit status by the current value.
BCM increases the turn signal lamp blinking speed if the bulb or harness open is detected with the turn signal
lamp operating.
NOTE:
B2607: S/L RELAY Inhibit engine cranking
500 ms after the following CAN signal communication status has
becomes consistent
Steering lock relay signal (Request signal)
Steering lock relay signal (Condition signal)
B2608: STARTER RELAY Inhibit engine cranking
500 ms after the following signal communication status becomes
consistent
Starter motor relay control signal
Starter relay status signal (CAN)
B2609: S/L STATUS
Inhibit engine cranking
Inhibit steering lock
When the following steering lock conditions agree
BCM steering lock control status
Steering lock condition No. 1 signal status
Steering lock condition No. 2 signal status
B260A: IGNITION RELAY Inhibit engine cranking
500 ms after the following conditions are fulfilled
IGN relay (IPDM E/R) control signal: OFF (Battery voltage)
Ignition ON signal (CAN to IPDM E/R): OFF (Request signal)
Ignition ON signal (CAN from IPDM E/R): OFF (Condition signal)
B260F: ENG STATE SIG LOST
Maintains the power supply
position attained at the time
of DTC detection
When any of the following conditions are fulfilled
Power position changes to ACC
Receives engine status signal (CAN)
B2612: S/L STATUS
Inhibit engine cranking
Inhibit steering lock
When any of the following conditions are fulfilled
Steering lock unit status signal (CAN) is received normally
The BCM steering lock control status matches the steering lock
status recognized by the steering lock unit status signal (CAN
from IPDM E/R)
B2617: STARTER RELAY CIRC Inhibit engine cranking
1 second after the starter motor relay control inside BCM becomes
normal
B2618: BCM Inhibit engine cranking
1 second after the ignition relay (IPDM E/R) control inside BCM be-
comes normal
B2619: BCM Inhibit engine cranking
1 second after the steering lock unit power supply output control in-
side BCM becomes normal
B261E: VEHICLE TYPE Inhibit engine cranking BCM initialization
B2620: NEUTRAL SW
Inhibit engine cranking
(Only when try to start the
engine while depressing
brake pedal and shifting to
the neutral position)
When any of the following BCM recognition conditions are fulfilled
Status 1
- Back up lamp switch signal: ON (Battery voltage)
- Park/neutral position switch signal: OFF (0 V)
Status 2
- Back up lamp switch signal: OFF (0 V)
- Park/neutral position switch signal: ON (Battery voltage)
Status 3
- Back up lamp switch signal: OFF (0 V)
- Park/neutral position switch signal: OFF (0 V)
B26E8: CLUTCH SW Inhibit engine cranking
When any of the following BCM recognition conditions are fulfilled
Status 1
- Clutch switch signal (CAN from ECM): ON
- Clutch interlock switch signal: OFF (0 V)
Status 2
- Clutch switch signal (CAN from ECM): OFF
- Clutch interlock switch signal: ON (Battery voltage)
B26E9: S/L STATUS
Inhibit engine cranking
Inhibit steering lock
When BCM transmits the LOCK request signal to steering lock unit,
and receives LOCK response signal from steering lock unit, the fol-
lowing conditions are fulfilled
Steering condition No. 1 signal: LOCK (0 V)
Steering condition No. 2 signal: LOCK (Battery voltage)
Display contents of CONSULT Fail-safe Cancellation
BCS
BCM (BODY CONTROL MODULE)
BCS-261
< ECU DIAGNOSIS >
[FOR SOUTH AFRICA]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
The blinking speed is normal while activating the hazard warning lamp.
FAIL-SAFE CONTROL BY LIGHT AND RAIN SENSOR MALFUNCTION
BCM detects the light and rain sensor serial link error and the light and rain sensor malfunction.
BCM controls the following fail-safe when light and rain sensor has a malfunction.
Fail-safe Control
Auto light control: Headlamp low beam, parking lamp, license plate lamp and tail lamp are turned ON.
Front wiper control
- Front wiper switch AUTO and sensing rain drop: The condition just before the activation of fail-safe is main-
tained until the front wiper switch is turned OFF.
- Front wiper switch AUTO and not sensing rain drop: Front wiper is LO operation until the front wiper switch is
tured off.
REAR WIPER MOTOR PROTECTION
BCM detects the rear wiper stopping position according to the rear wiper stop position signal.
When the rear wiper stop position signal does not change for more than 5 seconds while driving the rear
wiper, BCM stops power supply to protect the rear wiper motor.
Condition of cancellation
1. More than 1 minute is passed after the rear wiper stop.
2. Turn rear wiper switch OFF.
3. Operate the rear wiper switch or rear washer switch.
DTC Inspection Priority Chart INFOID:0000000005000938
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.
Priority DTC
1 B2562: LOW VOLTAGE
2
U1000: CAN COMM
U1010: CONTROL UNIT (CAN)
3
B2190: NATS ANTENNA AMP
B2191: DIFFERENCE OF KEY
B2192: ID DISCORD BCM-ECM
B2193: CHAIN OF BCM-ECM
B2195: ANTI SCANNING
BCS-262
< ECU DIAGNOSIS >
[FOR SOUTH AFRICA]
BCM (BODY CONTROL MODULE)
DTC Index INFOID:0000000005000939
NOTE:
The details of time display are as follows.
CRNT: A malfunction is detected now.
PAST: A malfunction was detected in the past.
IGN counter is displayed on Freeze Frame Data. For details of Freeze Frame Data, refer to BCS-203, "COM-
MON ITEM : CONSULT-III Function (BCM - COMMON ITEM)".
4
B2013: ID DISCORD BCM-S/L
B2014: CHAIN OF S/L-BCM
B2553: IGNITION RELAY
B2555: STOP LAMP
B2556: PUSH-BTN IGN SW
B2557: VEHICLE SPEED
B2560: STARTER CONT RELAY
B2601: SHIFT POSITION
B2602: SHIFT POSITION
B2603: SHIFT POSI STATUS
B2604: PNP SW
B2605: PNP SW
B2606: S/L RELAY
B2607: S/L RELAY
B2608: STARTER RELAY
B2609: S/L STATUS
B260A: IGNITION RELAY
B260B: STEERING LOCK UNIT
B260C: STEERING LOCK UNIT
B260D: STEERING LOCK UNIT
B260F: ENG STATE SIG LOST
B2612: S/L STATUS
B2614: ACC RELAY CIRC
B2615: BLOWER RELAY CIRC
B2616: IGN RELAY CIRC
B2617: STARTER RELAY CIRC
B2618: BCM
B2619: BCM
B261A: PUSH-BTN IGN SW
B261E: VEHICLE TYPE
B2620: NEUTRAL SW
B26E8: CLUTCH SW
B26E9: S/L STATUS
B26EA: KEY REGISTRATION
U0415: VEHICLE SPEED SIG
5
B2622: INSIDE ANTENNA
B2623: INSIDE ANTENNA
Priority DTC
CONSULT display Fail-safe
Freeze Frame Data
Vehicle Speed
Odo/Trip Meter
Vehicle condition
Intelligent Key warn-
ing lamp ON
Reference
page
No DTC is detected.
further testing
may be required.
U1000: CAN COMM BCS-221
U1010: CONTROL UNIT (CAN) BCS-222
U0415: VEHICLE SPEED SIG BCS-223
B2013: ID DISCORD BCM-S/L SEC-65
B2014: CHAIN OF S/L-BCM SEC-66
B2190: NATS ANTENNA AMP SEC-55
BCS
BCM (BODY CONTROL MODULE)
BCS-263
< ECU DIAGNOSIS >
[FOR SOUTH AFRICA]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
B2191: DIFFERENCE OF KEY SEC-58
B2192: ID DISCORD BCM-ECM SEC-59
B2193: CHAIN OF BCM-ECM SEC-61
B2195: ANTI SCANNING SEC-62
B2553: IGNITION RELAY PCS-51
B2555: STOP LAMP SEC-69
B2556: PUSH-BTN IGN SW SEC-72
B2557: VEHICLE SPEED SEC-74
B2560: STARTER CONT RELAY SEC-75
B2562: LOW VOLTAGE BCS-224
B2601: SHIFT POSITION SEC-76
B2602: SHIFT POSITION SEC-79
B2603: SHIFT POSI STATUS SEC-82
B2604: PNP SW SEC-85
B2605: PNP SW SEC-87
B2606: S/L RELAY SEC-89
B2607: S/L RELAY SEC-90
B2608: STARTER RELAY SEC-92
B2609: S/L STATUS SEC-94
B260A: IGNITION RELAY PCS-53
B260B: STEERING LOCK UNIT SEC-98
B260C: STEERING LOCK UNIT SEC-99
B260D: STEERING LOCK UNIT SEC-100
B260F: ENG STATE SIG LOST SEC-101
B2612: S/L STATUS SEC-107
B2614: ACC RELAY CIRC PCS-55
B2615: BLOWER RELAY CIRC PCS-58
B2616: IGN RELAY CIRC PCS-61
B2617: STARTER RELAY CIRC SEC-111
B2618: BCM PCS-64
B2619: BCM SEC-113
B261A: PUSH-BTN IGN SW PCS-65
B261E: VEHICLE TYPE
(Turn ON for 15 sec-
onds)
SEC-119
B2620: NEUTRAL SW SEC-114
B2622: INSIDE ANTENNA DLK-295
B2623: INSIDE ANTENNA DLK-297
B26E8: CLUTCH SW SEC-102
B26E9: S/L STATUS
(Turn ON for 15 sec-
onds)
SEC-105
B26EA: KEY REGISTRATION
(Turn ON for 15 sec-
onds)
SEC-106
CONSULT display Fail-safe
Freeze Frame Data
Vehicle Speed
Odo/Trip Meter
Vehicle condition
Intelligent Key warn-
ing lamp ON
Reference
page
BCS-264
< SYMPTOM DIAGNOSIS >
[FOR SOUTH AFRICA]
COMBINATION SWITCH SYSTEM SYMPTOMS
SYMPTOM DIAGNOSIS
COMBINATION SWITCH SYSTEM SYMPTOMS
Symptom Table INFOID:0000000005040157
1. Perform Data Monitor of CONSULT-III to check for any malfunctioning item.
2. Check the malfunction combinations.
Malfunction item:
3. Identify the malfunctioning part from the agreed combination and repair or replace the part.
Malfunction
combination
Data monitor item
F
R
W
I
P
E
R
H
I
F
R
W
I
P
E
R
L
O
W
F
R
W
A
S
H
E
R
S
W
F
R
W
I
P
E
R
I
N
T
R
R
W
I
P
E
R
O
N
R
R
W
I
P
E
R
I
N
T
R
R
W
A
S
H
E
R
S
W
I
N
T
V
O
L
U
M
E
T
U
R
N
S
I
G
N
A
L
R
T
U
R
N
S
I
G
N
A
L
L
T
A
I
L
L
A
M
P
S
W
H
I
B
E
A
M
S
W
H
E
A
D
L
A
M
P
S
W
1
H
E
A
D
L
A
M
P
S
W
2
P
A
S
S
I
N
G
S
W
A
U
T
O
L
I
G
H
T
S
W
R
R
F
O
G
S
W
A
B
C
D
E
F
G
H
I
J
K All Items
L If only one item is detected or the item is not applicable to the combinations A to K
Malfunction
combination
Malfunctioning part Repair or replace
A Combination switch INPUT 1 circuit
Inspect the combination switch input circuit applicable to the malfunctioning
part. Refer to BCS-226, "Diagnosis Procedure".
B Combination switch INPUT 2 circuit
C Combination switch INPUT 3 circuit
D Combination switch INPUT 4 circuit
E Combination switch INPUT 5 circuit
F Combination switch OUTPUT 1 circuit
Inspect the combination switch output circuit applicable to the malfunction-
ing part. Refer to BCS-228, "Diagnosis Procedure".
G Combination switch OUTPUT 2 circuit
H Combination switch OUTPUT 3 circuit
I Combination switch OUTPUT 4 circuit
J Combination switch OUTPUT 5 circuit
K BCM Replace BCM. Refer to BCS-266, "Exploded View".
L Combination switch Replace the combination switch.
BCS
PRECAUTIONS
BCS-265
< PRECAUTION >
[FOR SOUTH AFRICA]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER" INFOID:0000000005000941
The Supplemental Restraint System such as AIR BAG and SEAT BELT PRE-TENSIONER, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SRS AIR BAG and
SEAT BELT of this Service Manual.
WARNING:
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SRS AIR BAG.
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s)
with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly
causing serious injury.
When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution for Battery Service INFOID:0000000005000942
Before disconnecting the battery, lower both the driver and passenger windows. This will prevent any interfer-
ence between the window edge and the vehicle when the door is opened/closed. During normal operation, the
window slightly raises and lowers automatically to prevent any window to vehicle interference. The automatic
window function will not work with the battery disconnected.
BCS-266
< ON-VEHICLE REPAIR >
[FOR SOUTH AFRICA]
BCM (BODY CONTROL MODULE)
ON-VEHICLE REPAIR
BCM (BODY CONTROL MODULE)
Exploded View INFOID:0000000005048007
CAUTION:
Before replacing BCM, perform READ CONFIGURATION to save or print current vehicle specifica-
tion. Refer to BCS-190, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM) : Descrip-
tion".
Removal and Installation INFOID:0000000005048008
CAUTION:
Before replacing BCM, perform READ CONFIGURATION to save or print current vehicle specifica-
tion. Refer to BCS-190, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM) : Descrip-
tion".
REMOVAL
1. Remove dash side finisher (passenger side). Refer to INT-14, "Exploded View".
2. Remove bolt and nut.
3. Remove BCM and disconnect the connector.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Be sure to perform WRITE CONFIGURATION when replacing BCM.
Be sure to perform the system initialization (NATS) when replacing BCM. Refer to BCS-190, "ADDI-
TIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM) : Special Repair Requirement".
1. BCM
JPMIA1487ZZ
BCS
COMBINATION SWITCH
BCS-267
< ON-VEHICLE REPAIR >
[FOR SOUTH AFRICA]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
COMBINATION SWITCH
Exploded View INFOID:0000000005048009
Removal and Installation INFOID:0000000005048010
REMOVAL
1. Remove steering column cover. Refer to IP-11, "Exploded View".
2. Remove screws.
3. Disconnect the connector.
4. Pull up the combination switch to remove it.
INSTALLATION
Install in the reverse order of removal.
1. Combination switch 2. Combination switch connector
JPMIA1488ZZ