You are on page 1of 98

Page 1 of 98

TABLE OF CONTENTS


PAGE
GENERAL KILN SECTION
1 Description of Main Kiln System 04
2 Kiln Operation Priorities 05
3 Kiln System Stability 06
4 Main Parameters, Trends and Absolute Values 08
5 Main Parameters to Control and Evaluate Kiln 13
6 Variables which the Operator Cannot Control 15
7 Variables which the Operator Can Control 15
8 Kiln Limitation Factor 16
9 Kiln Operation Target 17
10 Optimization of Kiln System 18
11 List of Most Frequent Factors when Kiln Operation
Is not Satisfactory 19
12 List of Typical Kiln Operation Problems 20
13 What to Look for When Looking Inside a Kiln 21
14 Kiln Upsets 27
15 Kiln Cycling 28
16 How to Break a Cycle in a Kiln 29

KILN EMERGENCY CONDITIONS SECTION
17 Red Spot on Kiln Shell 30
18 Raw Unburned Feed in Clinker Cooler 31
19 Large Ring Broken Loose in Kiln 32
20 Burning Zone Dangerously Hot 33
21 Sudden Sharp Raise in Back End Temperature (B.E.T.) 34
22 Black Smoke Emission from Kiln Stack 35
23 Distorted Flame Shape 36
Page 2 of 98

24 Loss of Section of Refractory Lining 37
25 Cooler Drive or Clinker Conveyor Stopped 37
26 Red Clinker at Cooler Discharge 38
27 Rapid Rise of Temperature in Coal System 39
28 Power Failure 40
29 A Chain Fire 42
30 Heavy Rain or Thunder Storm 43
31 Sudden High Positive Pressure 43
32 Overheated Kiln Bearing 44
33 Kiln Hazardous Conditions 44

KILN OPERATION SECTION
34 Kiln Operation Techniques 47
35 Burning Zone Evaluation 48
36 Kiln Stable Temperature Profile 49
37 Target Set Point and Operation References 50
38 Back End Temperature Control 51
39 The Three Basic Variables 51
40 Target Range for the Three Variables 51
41 The Three Basic Conditions 52
42 The 27 Conditions (Kurt Peray) 53
43 Kiln Slow Down 56
44 Normal Operation Procedures on Shift 59
45 Plan of Action 59
46 Oxygen Level in Automatic Mode 60

KILN START-UP AND SHUTDOWN PROCEDURES
47 Light-up Flame Example (Gas) 61
48 Preheat or Drying of Refractory Lining 62
49 Heating to Reach Temperature Ready to put Feed On. 63
50 Feed On 64
Page 3 of 98

51 Kiln Start-up Procedures after a Brick Job 64
52 Example of How to Re-start if Preheat is Required 68
53 Example of How to Re-start if No Preheat is Required 69
54 Kiln Shutdown General Information 70
55 Cooling Procedures 70
56 Kiln Rotation Schedule 71
57 Burner Pipe and Hood Protection 72
58 Emptying the Feed from the Kiln 73
59 Kiln Shutdown Procedures for Brick Job and Red Spot 73

COOLER SECTION
60 Cooler Function 76
61 Cooler Operation 77
62 Cooler Controllers 77
63 Rule on Cooler Operation 78
64 Main Sensors to Control the Cooler Operation 79
65 Particle Size of Clinker 80
66 Operation of Cooler Fans 80
67 Clinker and Air Distribution 81

COMBUSTION SECTION
68 Flame 82
69 Rules on Flame 85
70 Combustion 86
71 Heat Transfer in Rotary Kiln 89
72 Burner Pipes and Nozzles 89
73 Fuels in Cement Industry 92
74 Solid Fuels 94
75 Drying, Grinding and Firing Solid Fuels 96
76 Comparison of the Three Major Fuels 97
77 Combustion Reaction 97
Page 4 of 98

78 Non-Combustibles (Ash) 98

BASIC PRINCIPLES SECTION
79 Basic Principles, System of Units 98
80 Temperature Scale n/a
81 Some Useful Conversion Factors n/a
82 Basic Principles, Pressure and Flows n/a
83 Basic Principles, Heat and Temperature n/a
84 Basic Principles, Heat Exchange or Transfer n/a


GENERAL KILN SECTION

DESCRIPTION OF MAIN KILN SYSTEMS

Wet Process
Better homogeneity of raw feed
Dust produced is approximately 15 to 20% of clinker production
Dust return to kiln by means of
Vortex at feed location (mixing problem)
Scoop near kiln discharge
Dust insulation in burning zone
Back end temperature is the main parameter to control and react on behavior of slurry through
chain system. (ring formation in chain, spillage near feed end)
High heat consumption (near 1300 kilocalories or 4676 MBtu/st), therefore there is a lower
secondary air temperature.
All other parameters are the same as a dry process kiln.

Long Dry
Feed is dry dust.
Page 5 of 98

Long residence time (up to 2 hours), so we have to take this into account when stabilizing the
kiln.
Heat consumption is approximately 920 kilocalories (3309 MBtu/st).
Natural load movement often unstable and creates pushes.

Pre-calciner and Pre-heater
Residence time in tower is from 2 to 5 seconds.
Residence time in kiln is approximately 30 minutes.
Fast reaction time, requires fast action to control the kiln.
About 50 to 90% calcinations is done in tower.
More stable than long dry, because calcinations is taking place in tower.
Heat consumption nears 800 kilocalories (2878 MBtu/st).
Very high secondary air temperature especially with pre-calciner need tertiary air duct.
Fuel ratio split: kiln = +/- 40%, pre-calciner = +/- 60%

KILN OPERATION PRIORITIES

1. Protection of the personnel working in and around the kiln system is a basic safety rule that
must be strictly followed at all times.

2. Protection of the equipment.
Around the kiln, the safety of the equipment is mainly related to overheating problems and
could be:
a) Back-end of kiln
Do not exceed 840
o
F (450
o
C) at precipitator inlet
b) Feed
Do not exceed 10 minutes without feed as the feed end temperature would go
high.
c) Chain inlet temperature
Do not exceed metallurgical maximum temperature of chain system. (usually
approximately 1900
o
F or 1038
o
C)
Page 6 of 98

d) Burning zone
Do not over-heat; keep the raw load near end of flame.
Set a maximum amps level on kiln motor.
e) Cooler
Avoid overloaded cooler grates, cut kiln speed down to protect the cooler
grates.
Avoid high exhaust gas temperature; could damage dust filter system.
Avoid high clinker temperature; could damage the clinker evacuation circuit.

3. Quality.
To produce a well-burned clinker with good free-lime at the desired liter-weight

4. Stability.
Continuous operation should always have priority over maximum production.
Stable kiln operation is the key to long refractory life, high fuel efficiency and uniform
quality clinker.

5. Optimization.
Strive for optimum production level at the lowest possible cost.


KILN SYSTEM STABILITY

1. Stable Feed
a) Chemical
Feed quality range should be:
+/- 0.4% in CaO
+/- 0.4% in SiO2
+/- 0.2% in Al2O3
C3S variations in clinker not to exceed +/- 3%
Page 7 of 98

Approximately 25% relative potential liquid phase in the clinker is good for kiln burning
and fuel saving.
b) Physical
Good and accurate feed rate indication.
Weigh-feeder should be linear at low, medium and high feed rate.
Good calibration by physical weight of the material should be done at every major kiln
shutdown.
Good feed and speed ratio.

2. Stable Dust Re-introduction to Kiln
Dust collector cleaning cycle sequencing.
Dust circuit configuration should provide stable re-introduction.
Monitoring of the dust return flow is an added advantage.
If dust wasting is required, wasting should be done in such a way not to upset the dust
return to the kiln.

3. Stable Water Spray Injection in Kiln or in Conditioning Tower
Good spray injects into gas stream, not in material load.
Good regulation of water injection with respect to ESP inlet temperature control. (will
cause changes in kiln oxygen level if water flow is not changing smoothly).

4. Good Chain System Design (Wet and Long Dry)
Act as a good dust curtain (dust trap).
Wet kiln design needs to favor a good plastic zone in order to prevent ring formation.
Chain tonnage should be between 12 to 14% of clinker production for large kiln and 10
to 12% for small kiln.
Good chains should stand high temperature so that in return enable high production
rates.

5. Good Control of Hood Pressure
Page 8 of 98

Hood pressure control is critical because it prevents the cooler variations to upset the
burning zone conditions.
Hood pressure set point should be set as close as possible to zero, while remaining
negative.

6. Stable Secondary Air Temperature
The temperature variations during normal operation should not exceed +/- 85
o
F (29
o
C)
Good regulation of the cooler under-grate pressure is then required with a thick clinker
bed depth.
The secondary air temperature should be as hot as possible, without damaging the nose
ring or the refractory at the kiln discharge section.

7. Good Production Level
Lower limit:
Under-60% capacity kiln tends to become unstable
Upper limit: Production restriction due to:
Kiln diameter; (maximum flame size, flame erosion on kiln walls).
ID fan capacity; (no leeway on oxygen level)
Precipitator capacity (cooler grates overloaded and high clinker temperature at cooler
outlet)

8. Constant Fuel Quality and Quantity
Constant fuel quality and quantity to allow constant heat input inside the kiln.


MAIN PARAMETERS, TRENDS AND ABSOLUTE VALUES

Back End Temperature
Set point varies with the kiln production level.
Set point varies with the condition of the chain system.
Page 9 of 98

Absolute value allows one to draw conclusions about efficiency of the kiln system and the kiln
operation.
BET trend is important for the kiln operation.
With the use of water spray in the back end, the water volume will show the reactions of the
back end temperature.

Material Temperature
Slow reaction compared to gas temperature.
In wet process kiln, material temperature is a good indication of the behavior of the material in the
chain system.

Chain Gas Temperature
This temperature is generally a limiting parameter for the kiln operation.
The chain gas temperature set point is generally fixed by the metallurgy of the chain system and
its design.
Absolute value is very important and must be held below the allowed T for the chain system.
The trend is representative but has slow reactions with respect to the back end temperature.
Very important to the kiln operation in order to make a good material preparation before it
reached the burning zone.

Burning Zone Temperature
Importance of this instrument is often overestimated.
Precise only when kiln conditions are clear.
The secondary air dust influence in the indication of the instrument and readings are in error
when kiln gets hot and dusty.
It must be correlated with the kiln amps indication and the secondary air temperature to ensure
the validity of the reading.

Shell Temperature (Scanner)
Importance of this instrument is underestimated.
Page 10 of 98

It is often used only to detect hot spots on the kiln shell, an estimation of brick thickness, and
coating in the kiln.
On bigger charts, it gives a good indication of the burning zone temperature profile.
It is one of the fastest indications of a slowly moving ignition point in burning zone.
It is a very good indication of flame variations due to the burner pipe position, flame shape and
direction. (Good indication when adjusting flame in kiln).
Absolute value is important to detect hot spots and rings.
Trend indicates changes in the burner system, kiln speed, ignition point movement and
operating conditions which are affecting the temperature profile of the burning zone.

Kiln Drive Amps
It is the most important sensor used to evaluate the burning zone state.
The running set point will change according to the raw material composition.
Amperage value changes with ring formation.
Amperage value changes with the size of the clinker.
The absolute value is important only when amperage is high (fuse protection limitations).
The trend is a very good indication of burning zone length and temperature; therefore the amps
should be recorded in such a way to give a good indication in its variations.
A drastic increase of the amps trend, followed by a fast decrease is an indication of loss of
coating or a broken ring inside the kiln.
A target amps range should be established (depending on raw mix and other factors) through
which this variable can fluctuate safely.
A drastic increase in amps could indicate a possible mechanical condition problem.

NOx Analyzer
Essentially it is an indication of the flame temperature. Higher is the flame temperature, the
higher will be the NOx concentration.
NOx content in the flue gases in the smoke stack originate partly from high temperature
synthesis in flame from oxygen and nitrogen.
NOx level has been measured in the range between 500 and 2000 ppm in the Lafarge group.
NOx increase with excess air and is strongly correlated to low excess air levels.
Page 11 of 98

At higher levels, i.e. 3% and greater, NOx is weakly dependent on excess air.
Correlation between burning zone temperature and NOx level is good.
NOx is generally, but not systematically correlated with the kiln drive amps. NOx gives a truer
picture of burning conditions. Kiln drive amps will change due to ring formation and
degradation, whereas NOx signal will not.
NOx correlates better with clinker liter weight than free lime.
NOx is affected by fuel changes. Natural gas flames yield the highest NOx level.
All the factors having an impact on the flame temperature will affect the NOx signal like the
following:
The secondary air temperature,
The primary air temperature,
The burning zone temperature,
Chemical composition and fineness of the fuel,
The air and fuel ratio and
The flame environment (reduced or oxidized atmosphere).
A quick decrease in the NOx signal is an indication of the burning zone temperature dropping.
A slow and even decrease on the NOx signal is an indication of a slow cooling of the burning
zone and is related to a bad material preparation from the kiln back end.
On the automatic kiln control system developed by Lafarge, the program is giving 30% of it as
evaluation of the burning zone state to the NOx signal, 55% to the kiln amps, and 15% to the
clinker temperature at the kiln outlet.

Secondary Air Temperature
It should be kept as stable as possible by the automatic cooler control system (+/- 85
o
F or 39
o
C).
Absolute value is not important because most indications are incorrect due to instrument
inaccuracy.
Trend is very important as it shows variations of material from the kiln and the gas temperature
variations to the kiln.
The secondary air temperature should be as high as possible in respect of the various refractory
temperatures in front of the kiln.

Page 12 of 98

Hood Draft
Absolute value is important and is automatically controlled at a constant value (usually looped
to cooler exhaust fan damper / fan).
It should be low as possible (to reduce in-leakage).
It is the separation between cooler and kiln and it should be always constant to avoid influences
of changes in the cooler gas flow to the kiln operation.
A poor regulation of this signal will induce variations in the kiln gas flow and could bring the kiln
into cycling.

Feed End Draft and ID Fan Draft
Trend and absolute value help to detect build-up in the kiln.
This is a very important sensor if many ring problems occur in a plant.

Cooler Exhaust Gas Temperature
Trend will give you information about the temperature profile in cooler gas flow variations and
clinker temperature.
Absolute value is an important limitation for protection of the dust collection system.
The cooler exhaust temperature is a more reliable clinker discharge indication than the clinker
temperature.

Clinker Discharge Temperature
Trend has no importance for cooler operation.
Absolute value is an important limitation for safety of the clinker transport system.
Clinker temperature measurements are generally not very accurate.

Under Grate Pressure
The absolute value should be maintained constant with automatic control.
The value varies with the cooler bed depth and with clinker size. It must be held constant in
order to achieve a constant secondary air temperature. Also, only a constant air flow can allow
the relationship between under grate pressure, bed depth and secondary air temperature to be
valid.
Page 13 of 98

Variations of the under grate pressures trend are reflected by variations in the cooler grate
speed.
Under grate pressures together with cooler drive amps, should give an indication of the clinker
size.
Under grate pressure set point should be at least 5 inches (H
2
O) in order to get good heat
recuperation from the clinker bed in the cooler.

Oxygen Analyzer
Trend and set point value are very important.
It should be maintained as constant as possible.
It can supply indications about general kiln conditions, burning zone and back end temperature.
One of the best indications when the kiln is pushing to indicate if the push is still on or over
(related with the amount of CaO in the kiln gases).
It should be kept as low as possible when the kiln is stable, without going into CO range.
However, when using coal or coke, set point should be increased to overcome the fuel quality
variations.



MAIN PARAMETERS USED TO CONTROL AND EVALUATE KILN


Kiln Amps
It is a very good indication of the burning zone state, accurate at 80% of the time.

NOx Analyzer
Nitrogen Oxide level is related to the flame temperature than the burning zone temperature.
NOx vary all the factors that has an effect on the flame.
It is a very good indication of the burning zone state.

Fuel Flow
Page 14 of 98

It should be related to the kiln feed rate.
It should be used as the main controller for the burning zone and the kiln back end temperature.

Kiln Speed
It should be related to feed rate.
It should be set with a constant feed ratio.
Small variations of the kiln speed (1 to 3 revs) could be used to control the burning zone state.
However, kiln speed variations should be used only after the fuel flow rate has been used as the
primary controller on long wet and dry kiln.
Often if over used, speed variations in the material loading of the kiln and will lead the kiln into
a cycle.
On large temperature variations in burning zone like raw material pushes, the kiln speed must
be used with wide variations (as example 30 revs or even a complete stop) to avoid raw
materials to go in the cooler and to re-heat the burning zone.

Fan Draft
It should be related to the oxygen level, fuel flow rate and feed rate.
It is the main controller to keep the temperature profile along the kiln.
The rpm variations should be small during kiln normal operation +/- 15 rph.
During kiln pushes and kiln slow speed, large speed variations will be required to maintain the
chain gas temperature under safe limit of the chain system.

Back End Temperature
It should be kept at constant level according to feed rate.
It should be kept stable in auto by the water spray system.
Good indication of the feed end T.
Indicate variations in the feed and dust variations to the kiln.
When in auto, use water flow variations for indication.

Gas Temperature
It is the main variable to control the kiln.
Page 15 of 98

It should be kept inside a certain T range.
It is controlled by the ID fan speed variations and the fuel rate.

Oxygen level
It is related to the ID fan speed and fuel rate.
Minimum and maximum level limits need to be established, to control combustion efficiency.
When kiln stability has been reached the O2 level should be set in auto with the ID fan speed to
lock the temperature profile of the kiln.

Hood Pressure
Control of excess air by cooler exhaust fan
Open during kiln pushes
Need to be kept stable to avoid variations in cooler to upset the burning zone

Secondary Air Temperature
Temperature of combustion carried back to kiln from the cooler
Large variations during kiln pushes
Should be controlled in a very small range in auto during normal kiln operation with a good
regulation of the clinker cooler (+/- 85
o
F or 39
o
C)

Cooler Exhaust Temperature
Varies with clinker input to cooler
Will indicate variations during a push

Under Grate Pressure
Related to cooler grate speed
Set point controlled by the under grate pressure of second compartment to keep a constant clinker bed
depth in order to get stable and high secondary air temperature


VARIABLES WHICH THE OPERATOR CANNOT CONTROL
Page 16 of 98


Quality and characteristics of the raw materials
Quality of the fuel used as a example: heat value, ash content, volatile matter and moisture level
Dust quality and quantity returned to the kiln
Accuracy of the feeders
Chain system design
Accuracy and good response of all control loops and sensors of the kiln system

For these variables that he cannot control, the operator should be kept informed of any changes done
and should make sure that those variables are kept inside an acceptable range to maintain a good kiln
stabilization.


VARIABLES WHICH THE OPERATOR CAN CONTROL

Material feed to the kiln
Fuel feed to the kiln
Speed rotation of the kiln
Temperature profile along the kiln
Draft at the feed end of the kiln
Supply of combustion air
Retention time of the material in the kiln
Temperature of the combustion air
Flame shape
Observation of instruments, and correct reaction to their readings
Observation of the kiln burning zone, and correct reaction to this evaluation
However, some restrictions are sometimes given on the utilization of those variables and may vary from
plant to plant due to local conditions and are usually the following:
Set point on the maximum speed of the kiln
Set point on the maximum feed rate to the kiln
Automatic loop set point for oxygen level and ID fan speed
Page 17 of 98

Settings on the burner pipe and its position
Primary air settings and fuel tip velocity
Set point on cooler fans flow
Set point for the under grate pressure and the clinker bed depth in the cooler


KILN LIMITATION FACTORS

Dust Emission at Precipitator Stack (Local emission regulations)

Gas Chain Temperature
Maximum value depend on chain quality and position

Diameter of Kiln
Gas velocity in kiln (70 ft/sec in free section of kiln and 30 ft/sec in chain section maximum)
Heat load in front of kiln, flame erosion on kiln walls

ID Fan Capacity
Maximum fan speed and low oxygen level

Cooler Capacity
No red clinker should be present after third compartment of cooler in normal operation
Clinker discharge temperature not to exceed 170
o
F (80
o
C)
Cooler exit gas should be about 370
o
F (190
o
C)
Bed depth to allow good under grate pressure (15) with sufficient fan capacity


KILN OPERATION TARGET

Highest clinker production with
Good quality clinker
Page 18 of 98

Stable kiln operation

Oxygen level as low as possible
Gas and fuel oil 1.0 to 1.5%
Coal and coke around 2.0% (depending on the variations in fuel mixture)

Kiln exit temperature as low as possible
Flame as short as possible (with respect of the burning zone refractory)
Keep burning zone short in front of the kiln

Secondary air temperature as high as possible but stable
Temperature not above liquid phase temperature in front of kiln to protect refractory and
coating
Run with an under grate pressure as high as possible
Compatible with the cooler fans static pressure capacity

Primary air as low as possible
As combustion air to replace by hot air from cooler as much as possible

Clinker Temperature
Not to exceed 230
o
F (110
o
C) as it could promote quality problems (false set) during the grinding process

Gravel bed filter
Normal operation temperature is 350
o
F (180
o
C)
Maximum temperature for normal operation is 660
o
F (350
o
C)
For 2 hours, up to 750
o
F (400
o
C)
For 20 minutes, up to 840
o
F (450
o
C)



OPTIMAZATION OF THE KILN SYSTEM
Page 19 of 98


Operate the kiln:
With higher free lime

Reduce air leakages:
Around and near the nose ring area and seal
Air in-leakage on kiln hood
Around blast pipe port holes and doors
Hood pressure set point as close as possible to zero
Primary air should be kept as low as possible

Reduce length of pre-cooling zone by:
Adjusting the burner position
Proper material load (kiln speed/feed ratio)
Increase clinker bed depth in cooler (near 15 inches)
Oxygen to be maintained at minimum level
Good flame shape and temperature

Good chemical composition
Good burnability factors
Constant raw mix



TYPICAL KILN PROBLEMS


List of most frequent factors at work when kiln operation is unsatisfactory

1) High leakage, pre-heater only into feed end seal (more than 5%)
Page 20 of 98

2) Faulty suspension results in high pre-heater outlet temperatures, thus reduces capacity (bleed
air)
3) Poor operating practices (burning techniques)
4) Reducing conditions in kiln
5) Reducing conditions in burning zone due to flame impingement with load
6) Lack of momentum at burner tip leads to long, lazy flame
7) High primary air, (30%+) due to direct firing of coal, (critical in dry process kiln)
8) High level of volatile elements in raw feed particularly chlorine
9) Systematically hot burning
10) Inadequate chain system
11) Poor cooler heat recovery due to cooler fan design
12) Poor cooler heat recovery due to excessive air flows, insufficient pressure in under grate
compartments
13) Chemically variable raw mix C
3
S, more than 10 points over a shift
14) Variable slurry moisture (more than 3 points)
15) Variable addition of hi-alkali or hi-volatile dust from precipitator (over a period of more than
one-half hour)
16) Erratic feed rate
17) Erratic fuel rate (wet coal)
18) High leakage into hood seal (more than 10% of combustion air)
19) Inadequate or obsolete design of equipment or facilities
20) High leakage into pre-heater and down-comer duct
21) Flame erosion on lining could create premature brick failure
22) Kiln misalignment, excessive tire clearances and other factors of shell deflection
23) Bricking techniques lead to rings not tight enough
24) Low slurry moisture
25) High slurry moisture


List of Typical Kiln Operating Problems

Page 21 of 98

1) Heat consumption higher than normal
Long dry: Higher than 3.4 MBtu/ton
Long wet: Higher than 5.2 MBtu/ton
Four stage Pre-heater: Higher than 3.1 MBtu/ton
2) Output lower than nominal and / or standard
3) Kiln is unstable and requires frequent massive shutdowns
4) Kiln is cycling spontaneously without any action of operator
5) Kiln is out of draft with output below nominal
6) Stack stinks SO2 emissions are high
7) Mud ring in chain section on wet kiln
8) Back-spills on wet kiln
9) Burning zone rings
10) Discharge end rings
11) Snowmen in cooler
12) Frequent burning zone burnouts (brick life is less than 3 months)
13) High dust return (above 20% of clinker) causes handling problems
14) Cyclones plug-ups (four stage pre-heater)
15) Build-ups in pre-heater feed box (four stage pre-heater)
16) Cooler exhaust system seems undersized/under-designed
- Hood frequently under pressure (during pushes)
- Exhaust temperature is higher than normal
- Bleed in damper is open very often
- Frequent bag burnouts in cooler bag house
17) Red grates in the cooler all the time. Frequent grates burnouts
18) Red rivers on side of cooler
19) Under pushes, cooler speed up to maximum, yet some fans stop blowing any air (pressure
overload)
20) Kiln drive seems undersized, kicks out upon start-up after a short shutdown


WHAT TO LOOK FOR WHEN LOOKING INSIDE A KILN
Page 22 of 98


Viewing the kiln interior

This may sound somewhat elementary, but we should never forget that we are looking into an
extremely luminous source. Although filtering glasses are used, the light source is so strong that focusing
the eyes into it for too long a time could cause partial blindness. One should look no longer than one
minute at a time into the fire. If longer viewing is required, look a side for few seconds occasionally to
rest the eyes. Looking steadily too long at the flame results in the eye losing its ability to see details,
hence the need for a short rest every minute or so.
The question of what type of colored filter glass to use must be left to the operators. Burning
with a natural gas flame usually makes necessary a darker colored than oil fire would require, because of
the greater luminosity of the flame. As a rule, one should always use a glass that enables him to see
under and behind the flame. Once a certain glass has been chosen, the operators should stay with this
glass at all times in order to properly judge the burning zone conditions. How frequently should one look
into the burning zone? There is no set answer to this question. Experienced operators sometimes
become over-confident and think that it would be perfectly safe to leave the kiln alone for periods in
excess of 30 minutes. This action however, is against good burning practice. The secret of every good
operator is his ability to recognize a change in kiln condition at the time a change takes place and not
later. For this reason, a good operator will never leave a kiln too long a time unchecked. When things
are going smoothly, the kiln should be checked every half hour, with more frequent checks if
adjustments are being made. There is no such thing as operating a kiln by the instrument alone, as the
instruments do not show, for example heavier and lighter loads entering the burning zone until it is
almost too late to make the necessary adjustment.


The kiln condition can be estimated from the color observed in the hottest part of the flame.

Dark red cherry red orange-yellow white
Cold - - normal hot
Any deviations from the orange-yellow range should be investigated to determine the cause and when
adjustments need to be made to the kiln operation to get back to normal kiln condition.
Page 23 of 98



Appearance of burning zone

Good or bad visibility
Bright white or dark red color
Good appearance is an orange-yellow color
The gas stream should be calm without great turbulence


Appearance of coating

Coating should begin approximately diameter of kiln size from the nose ring
Color of coating tells a great deal about the condition in burning zone as coating acts as heat
storage in burning zone
Overall thickness of coating should be between 9 and 12 inches and is dependent of the type of
raw mix
Check for ring formation near lower or upper section of the kiln
If the surface of the coating appears smooth, then the burning zone in this area is hot
If the coating appears lumpy then the burning zone is okay
A bare spot without coating could be due to flame erosion, thick brick or high flame
temperature in this location
Appearance of the coating falling off from the top of the kiln shell:
Large pieces: normal
Fine noodles dripping: too hot
The location where the coating pieces are falling from the top of the kiln wall, above the end of the
flame is generally where the raw load is. So whenever the raw load cannot be seen in the bottom and
behind the flame of the kiln, try to look at the top.


Appearance of material load
Page 24 of 98


Is clinker balling or fine?
Is material sticky?
Is material heavy or light?
Is material movement fast or slow?
Is material climbing low or high in the wall? (material should climb up +/- to the 10 oclock
position in normal operation)
Appearance of material before falling in the cooler, fine or nodular

Upper burning zone section

Are rings building up or not?
Is coating formation seem normal?
Try to evaluate the length of the coating (50 to 100 feet from burning zone to far up)

Raw feed location

Look behind the flame at the bottom of the kiln
Normal position is approximately diameter distance under the flame
Never allow raw feed to come way under the flame as kiln speed will have to be reduced to
control it (kiln low speed)
An advancing or receding dark feed is the earliest indication of a burning zone that is warming up or
cooling down. So that is why it is important for the kiln operation to be able to see this load. Every effort
should be done during normal operation to keep this load in sight.

Flame appearance

Should always be evaluated during stable kiln condition
Long (100 ft) or short (30 ft)
Hard or lazy
Bushy or narrow
Page 25 of 98

Bright or dark
White or orange yellow
Eroding the coating or the brick wall
Aiming high, low or in the center
Eroding the material load
If fuel is burning in suspension or in the material load
Position of the ignition point when coal or coke is used
The flame temperature should be as hot as possible as long as it does not create problems with the
coating and the kiln refractory. Whenever a change is made on the flame shape, a close monitoring of
the shell temperature should be done.

Coal flames

Coal normally burns with longer flame than oil
A coal flame normally starts at 3 to 5 feet from the burner tip
Coal fineness to be about 85% passing 200 mesh
Keep the coal system air flow at about 70 ft/sec to avoid coal deposit inside pipe, while keeping
primary air to minimum (direct system and burner design)
On direct firing system, coal fan damper setting should be set at minimum value and the fuel rate
changes made only by making changes with the coal feeder system in order to keep the flame shape
short and as constant as possible.

Burner pipe appearance

Is the tip of the blast pipe in good condition?
Is the burner cast-able in good condition?
Is the burner pipe aimed correctly?
How is the pipe location relative to the nose ring?
Are snowmen building up on top of burner pipe?
Whenever a bad condition deflecting the flame is observe, a quick evaluation should be done to
evaluate if the kiln can continue its operation or if it needs to be shut down to fix the burner pipe.
Page 26 of 98


Nose ring appearance

Check the condition of the cast-able or the refractory on the top of the nose ring if okay
Check the temperature aspect and the wear of the nose ring castings
Check if the nose ring seal is in good condition

Secondary air

Calm or upset
Dusty if the clinker is fine
Clear if clinker is balling
Foggy and white if temperature is hot
The secondary air temperature has a major influence on the flame and its shape.


Primary air

Should be as low as possible to obtain satisfactory heat recuperation from cooler
Has an important influence on the shape of the flame (bushy or narrow)
Pressure should be as constant as possible
When good settings of the flame have been found, the primary air settings should not be changed in
normal operation unless a high temperature condition in the kiln refractory has raised and required to
change the flame.


When the kiln is down

Look for ball or ring formation at upper section of burning zone
Evaluate length of coating if okay, too long means we burned the kiln too far up
Load level inside kiln if even and normal
Page 27 of 98

Appearance on load during kiln jacking (sticky or normal)
Look at the sealing efficiency of the kiln back end (no suction or gases movement inside of kiln should be
observed).
When kiln is shutdown, the gases should be bottled inside of the kiln as fast as possible by closing the
kiln back end damper or its equivalent and by adjusting the hood pressure set point, slightly positive.
The procedure need to be done to avoid heat loss from the kiln to insure a slow cooling of the refractory
and avoid thermal shocks on the bricks.
KILN UPSETS


Burning zone too hot

Too much liquid is formed and all temperatures are above the solid state temperature therefore no
coating is formed. Coating will be lost and this could damage the refractory.
A) Appearance the kiln could be white and hazy in front end and the clinker will be balling.
B) Appearance of the kiln could appear cold if burning is too far. The clinker could be fine (very
long burning zone).

A) Hot burning zone with high secondary air temperature

The front of kiln is very hot and white, often hazy
The secondary air temperature is high
The clinker is balling and getting bigger
Often the dark load is visible behind the flame
These conditions occurs when the burning zone length is moving down and concentrating the
heat on a shorter burning zone length in front of kiln.
This situation can be overcome quite easily by reducing the fuel rate and the ID fan slowly step
by step until the burning zone gets back to its normal condition.


B) Hot burning zone with dusty secondary air
Page 28 of 98


Can be caused by burning too far back into the kiln
Flame too long and ignite too far
Pre-cooling zone is too long in front of the kiln
Long burning zone promotes very fine clinker formation which is sent back as dust into the
kiln with the secondary air gas stream
Whenever dusty conditions prevail in front, corrective measures should be based on the
clinkering conditions behind the flame rather than on the color of the front of the kiln.
Aspect of the clinker falling in cooler is very important at that time to evaluate the kiln
condition.
Kiln amps, fuel flow rate, shell temperature and back-end temperature are usually
above the normal operation settings during these conditions.
Get free lime done from clinker coming out of the kiln to see if OK
If operator is in doubt about the kiln being cold or hot, the kiln rotation could be
stopped (out of the interlock for a few seconds) to allow condition of the burning zone
to clear and to view inside the kiln
If doubt still persists, the kiln should be assumed to be hot and it should be cooled down
by reducing the fuel and the ID fan speed until the burning zone get back normal or end
up to be completely cold.
Except for very hot and emergency conditions, such as cooling should take as long as a
full shift to be done, to avoid high heat concentration in front and quick losses of
coating from the upper section of the burning zone which could upset the burning zone
temperature.



KILN CYCLING

This is an unstable condition when the load in the kiln decreases, causing the temperature of the
burning zone to rise and forcing the operator to reduce the fuel rate. Then, the burning zone starts to
cool off in turn forcing the operator to increase the fuel rate. In severe cases, the temperature continue
Page 29 of 98

to drop, even though the fuel rate is at maximum and it become necessary to reduce the kiln speed to
slow down the entry of the feed into the burning zone. Once a kiln gets into an upset such as this, the
cycle will repeat.

Kiln cycling could be related to the following reasons;
Variations in kiln feed: physical or chemical,
Variations in dust re-introduction to kiln,
Variations in the water spray control system in kiln inlet (if any),
Materials hold up in the chain system (for wet process kilns),
Poor chain system design (for wet process kilns),
Variations in hood pressure control
Poor cooler settings and control which promote secondary air temperature variations,
Operating the kiln above its production capacity,
Variations in the quality and the quantity of the fuel supply to the kiln,
Bad operating practices, especially over reacting with the kiln speed and
Volatile recirculation inside the kiln system especially chlorine
So all the above reasons should be investigated in order to find the cause of the cycling problem and
corrected.



HOW TO BREAK A CYCLE IN A KILN

Reduce feed/speed ratio by approximately 10% in order to change the material load in the kiln
(also mainly to change the material load in the chain system).

Increase the fuel flow rate by 5% above the normal setting of the current production level.

Keep the oxygen level above 2% and try to control the back end temperature variations as much
as possible by using fuel rate and ID fan variations.

Page 30 of 98

Let the kiln amps vary and do not attempt to chase them by varying the kiln speed. Just try to
control them if they get above or below the critical range by varying the fuel flow rate.

If the kiln speed need to be varied than it should be done with very small variations, in order to
avoid upsetting the material in the kiln.

If the kiln speed needs to be increased to go back to normal production level, then it should be
carried out more slowly than normal.

As you get to normal production level, fuel settings should be held above normal before returning to
normal operation settings.


KILN EMERGENCY CONDITIONS SECTION

RED SPOT ON KILN SHELL

Indicators:
By visual observations
Shell scanner sharp and rapid shell temperature increase to level above 850
o
F (450
o
C)
Visual observations of loose refractory bricks in the material load of the kiln or in the clinker at
the cooler discharge

Possible Effects and Danger
Severe warping and damage to kiln shell
Shell temperature between 900 and 1100
o
F (480 and 590
o
C), deep red color on shell
Shell temperature over 1200
o
F (650
o
C), very bright red and shell bulges and warps

Recommended Actions to Take
A) For small red spot located in the upper transition or center of burning zone
Continue normal operation of kiln but:
Page 31 of 98

Place shell cooling fans in the area of red spot
Shorten flame to bring black feed over area of red spot in attempt to form new coating
Keep watching the shell temperature trend
Maintain normal burning zone temperature
Change kiln feed chemistry to obtain an easier burning mix
B) For large red spot located under or near a kiln tire or in areas were no coating is formed
SHUT DOWN KILN IMMEDIATELY
Warning: Under no circumstances should a water spray be used on the red spot, as this
could result in severe kiln shell damage.

Possible Measures to Prevent Re-occurrence
Make sure flame configuration and characteristics are not causing localized coating erosion or
continuous and excessive overheating
Employ proper refractory installation methods
Minimize frequency of kiln shutdowns and upsets
Minimize frequency of clinker type changes over
Avoid hard burning mixes (i.e. ensure sufficient percentage of liquid content in mix to
promote coating formation)


RAW, UNBURNED FEED IN CLINKER COOLER

Indicators:
On rush of raw feed into and beyond burning zone
Black feed position advanced more than way under the flame
Black-out in burning zone
Red grates in cooler
Rapid rise in cooler grate and clinker discharge temperatures
Cooler drag-chain amperage increases rapidly

Possible Effects and Danger
Page 32 of 98

Thermal damage to cooler grates and grate drive mechanism
Fire on clinker conveyor belts
Excessive high temperatures in coal mill air circuit
Warning: Watch for incomplete combustion when visibility in burning zone is severely restricted.

Actions to Take
First and foremost, do not wait until raw feed is in the cooler; act when the first signs of impending
problems are visible in the burning zone.
Immediately reduce kiln speed to minimum (or turn on auxiliary drive)
Reduce fuel and ID fan speed in accordance with standard slowdown procedures to protect the
kiln back end temperature
Reduce cooler grate drive speed (switch to manual control) to allow material in cooler more
time for cooling
Adjust cooler air flow rates to obtain maximum cooling without the hood pressure going positive
Advise all unauthorized personnel to stay clear of the firing floor, cooler and coal mill area

Preventive Measures to Avoid Re-occurrence
Accelerate frequency of visual observations of burning zone for early detection of impending
cooler upsets
Evaluate kiln output rates vs. capabilities and kiln operating stability


LARGE RING BROKEN LOOSE IN KILN

Indicators
Visual observations of large junks in burning zone
Sudden drop in kiln back end draft
Large drop in oxygen content of kiln exit gases
Hood pressure tending towards positive side
Sudden change in kiln drive amperage

Page 33 of 98

Possible Effects and Dangers
Overloading cooler with unburned feed
On rush of excessive amounts of feed into the burning zone
Damage to cooler drives and grates
Large pieces jamming cooler hammer crusher
Red hot clinker leaving cooler
Actions to Take
When amount of feed and ring fragments in burning zone are extremely large:
Immediately reduce kiln speed to minimum
Reduce fuel and ID fan speed to keep back end temperature under control
Switch cooler grate control to manual and reduce grate speed
Adjust cooler air flows to maximum flow possible, without the hood pressure going positive
Have personnel on standby to watch the cooler and the hammer crusher for possible
overloading, overheating and jamming

Possible Preventive Measures to Avoid Re-occurrence
Laboratory to reevaluate chemistry of kiln feed (including dust return rates) for possible
elimination of ring formation if no solution in this area possible, then
Initiate regular schedule to remove rings and heavy build-up by means of special devices design
for this purpose
Initiate regular procedures to displace the burning zone location on a daily basis


BURNING ZONE DANGEROUSLY HOT

Indicators
Clinker balling in burning zone
Material load sausage-like
Coating dripping off the wall
Sliding molten clinker bed in burning zone
Burning zone recording temperature too high
Page 34 of 98

Cooler under grate pressure too high
Material load turning to liquid in burning zone
Very brilliant and white burning zone

Possible Effects and Dangers
Loss of coating and thermal damage to refractory
Red spot in the kiln shell
Thermal damage to cooler and kiln hood components

Possible Actions
Reduce fuel flow rate to minimum until sausaging stops
Increase kiln speed approximately 10 rph until sausage is broken
Provide maximum air in cooler (without hood pressure going positive)
The kiln rotation to be adapted is the aspect of the material near to fall into the cooler. No liquid
material in the cooler, stop kiln rotation if needed.
Reduced primary air flow, then as soon as the objective of breaking the agglomeration is
accomplished,
Reduced the kiln and ID fan speed then increase fuel flow rate to normal operating conditions

Preventive Measures
If sausaging is frequent and result of easy-burning mix, have laboratory evaluate possibility of
providing a mix with less percentage of liquid content
Make more frequent, vigilant observation of the burning zone conditions
Evaluate flame position and shape to determine if thinner, longer flame is possible


SUDDEN, SHARP RAISE IN BACK-END TEMPERATURE

Possible Reasons
Feed shortage
Combustion in exit gas
Page 35 of 98

ID fan speed too high
Kiln speed too low
Chain fire

Possible Effects and Dangers
Chain fire on wet and dry kilns
Thermal damage to back end, dust collector and pre-heater tower equipment
Delayed ignition of fuel in back end of kiln

Possible Actions
Immediately de-energize electrostatic precipitator
Immediately reduce fuel flow rate and ID fan speed to obtain less than 0.3% oxygen in exit gas
Warning: Do not cut off fuel flow rate completely as this could trigger an explosion.
Increase kiln speed and feed rate
Warn personnel to stay clear of kiln back-end
Do not open any doors in kiln back-end
Then as soon as the primary objective of bringing the kiln back-end temperature under control is
accomplished:
Return kiln control variables to normal to restore operating conditions
Check out back-end to determine if thermal damage had occurred

Preventive Measures
Do not operate kiln without feed for more than 10 minutes
Provide alarms and properly maintain kiln instrumentation to obtain warnings before the back-
end temperature gets out of maximum range
Maintain close vigilance over combustion, back-end and flow conditions during kiln starts,
shutdowns and upsets


BLACK SMOKE EMMISION FROM KILN STACK

Page 36 of 98

Indicators
Combustibles in exit gases
Oxygen in exit gas too low
Flame extinguished for poor ignition conditions
Burning zone temperature too low
Excessive fuel rates and/or insufficient kiln draft
Possible Actions
Immediately de-energize electrostatic precipitator
Immediately reduce fuel flow rate (do not shut off)
Increase ID fan speed to obtain:
a) Zero combustible in exit gas
b) Oxygen between 0.2 and a maximum of 0.5% in exit gas
After black smoke has cleared, maintain the low oxygen/zero combustibles for at least 10
minutes before restoring kiln variables to normal

Preventive Measures
Improve control over flame and firing conditions
Make frequent, vigilant observation of fuel flow rates, gas analysis, flame and kiln draft
conditions during kiln starts and upsets


DISTORTED FLAME SHAPE

Indicators
Irregular and unusual flame shape
Fragmented flame where part of flame impinges on lining near kiln discharge area

Possible Effects and Dangers
Inspect burner pipe for damage or plugged circuit
If flame is erratic and severely impinges upon lining near the kiln discharge area:
Shutdown kiln immediately!
Page 37 of 98

If flame is only slightly distorted; adjust burner position and primary air flow
Check shell temperature on kiln scanner
Schedule a burner pipe repairs for next kiln shutdown

Preventive Measures
Frequent visual inspection when looking inside the kiln
Regular inspection and maintenance of burner pipe during each prolonged kiln shutdown
Improve protection (castables, air cooling) for burner pipe
Maintain primary air flow for at least 2 hours after a kiln has been shutdown or pull back the
burner pipe immediately when kiln is being shutdown


LOSS OF SECTION OF REFRACTORY LINING

Indicators
Loose bricks in clinker bed of burning zone
Delineated (linear instead of round) red spot on kiln shell
Rapid rise in kiln shell temperature

Possible Effects and Dangers
Thermal damage and distortion of kiln shell and tire
Further collapse of large sections of linings (especially in alumina brick sections)

Possible Actions
Immediately shutdown the kiln

Preventive Measures
Employ proper refractory installation methods and procedures
Make annual checks of kiln alignment and shell ovality
Have refractory manufacturer provide uniform shapes and proper expansion allowance for each
type of brick
Page 38 of 98

Avoid excessive turning when kiln is cold during shutdowns


COOLER DRIVES OR CLINKER BELT STOPPED

Indicators
Cooler overloaded
Large chunks of coating in cooler
High under grate pressure
High cooler drive amps prior to drive stop
Clinker transfer chutes plugged

Possible Effects and Dangers
Thermal damage to cooler components

Possible Actions
Immediately reduce kiln speed to minimum and attempt to restart clinker belt and/or cooler
drive
If drives cannot be restarted within 5 minutes, shutdown the kiln
Note: After kiln has been shutdown, consider possibility of turning the kiln in less frequent intervals
to prevent further overloading of cooler. (Kiln still had to be rotated periodically nevertheless)

Preventive Measures
Know at what amperage the cooler drive is likely to fail and provide alarm for overload
Adjust kiln parameters (namely kiln speed) before cooler can become overloaded at the times
when heavier feed load is observed in the burning zone


RED CLINKER AT COOLER DISCHARGE

Indicators
Page 39 of 98

High drag chain amps
Sudden drop in under grate pressure (grate out)
Excessively high under grate pressure (cooler overloaded)
Cooler drive amps and clinker bed depth too high
Cooler loaded with coating and ring fragments
Snowman formation at cooler inlet

Possible Effects and Dangers
Thermal damage to cooler components
Thermal damage to clinker transport equipment

Possible Actions
Immediately make a visual check of the cooler to determine reason for red-clinker discharge
If cooler grate out, shutdown kiln
If cooler overloaded, reduce kiln speed to minimum and reduce cooler grate drive speed to
allow more time for cooling
Increase air flow into cooler
Activate water spray at cooler discharge and reroute clinker to prevent damage to conveyor
belts

Preventive Measures
a) On frequent grate failures
Investigate for possible faulty grate installation methods by maintenance department
Investigate quality of grates and bolts used
b) On frequent one-sided loading of cooler bed
Investigate possible cooler design changes
Investigate possibilities for elimination of stalagmite (snowmen) formation at cooler
inlet
c) On frequent overloading of cooler due to upsets
Slow down kiln speed before raw feed enters cooler or cooler can become overloaded
(make your corrective moves before things get out of control)
Page 40 of 98



RAPID RAISE OF TEMPERATURE IN COAL SYSTEM

Possible Effects and Dangers
Explosion
Thermal damage to coal system

Possible Actions
Warning: Do not open any door in the system that could provide the oxygen for an explosion or
a more serious fire.
Inject inert gas (CO2) into coal mill inlet
Flood coal mill with kiln feed or excessive coal
Warn all personnel to stay clear of system
Stop or reduce air flow to coal mill to minimum

Preventive Measures for Re-occurrence
Provide coal mill inlet with magnetic device to extract metal fragments from coal feeder belt
Keep paper, rags, etc. out of coal storage pile
Do not feed coal mill with coal that has undergone spontaneous ignition (smothering) while in
storage
Keep coal mill de-tramp chute clear
Provide coal mill system with automatic fire-extinguishing devices
Do not operate coal mill above predetermined safe temperature for any given type of coal


POWER FAILURE

Possible Effects and Dangers
Warping of kiln shell
Thermal damage to burner pipe, instrumentation and equipment at kiln discharge area
Page 41 of 98

On coal-fired kilns, settlement of ground coal in coal system that could lead to a fire and/or
explosion

Possible Actions
Immediately start auxiliary power generator and primary air fan (coal mill fan on direct fired
kilns)
Retract burner pipe and protect TV monitor in kiln hood
Start turn on kiln not later than 10 minutes after the power failure
If available, close feed-end damper manually to prevent hot gases from escaping from kiln by
natural draft

Power Failure Main Procedures
Start generator or auxiliary drive
If it is raining, carry out turn as described previously
Close kiln back-end, ID fan damper, or precipitator inlet damper if power failure is of long
duration
Keep primary air fan running to cool down the burner pipe (and pre-calciner burners) or pull the
burners out of the kiln
Try to restore power as soon as possible

The following should be connected on the auxiliary power system:
Emergency light in control room
Emergency light in kiln platform
Telephone system for outside calls
Radio system inside the plant
ID fan louvers and precipitator inlet damper
Kiln auxiliary drive
Primary air fan
Recirculation pump for the industrial water system (water cooling system)

Page 42 of 98

Instructions should be given to all members of the shift for specific responsibilities during a power
failure as example:
Operator A:
Carry out safety procedures on kiln system
Start the auxiliary power system
Close kiln back end (if on auxiliary system)
Rotate the kiln
If it is raining continuously, rotate kiln as soon as possible
Protection of burner pipe (pull out of kiln
Call the power company

Operator B:
Get to main power breaker and try to reset it
Go to kiln back-end and close ID fan louvers (if they are not connected on the auxiliary drive)
If the auxiliary drive control is not remote, make kiln rotation in local


A CHAIN FIRE

Indicators
Rapid, sudden rise in intermediate and exit gas temperatures
By visual observation

Possible Effects and Dangers
Melt-down and loss of chains
Damage to kiln shell in chain system area
On wet process kilns; steam explosion
Thermal damage to kiln back-end equipment

Possible Actions
Warning: Under no circumstances should water be added at the feed end.
Page 43 of 98

Immediately reduce fuel rate to minimum (but dont shut fuel off completely)
At the same time, reduce ID fan speed to obtain zero combustibles and less than 0.3% oxygen
Increase kiln speed and feed rate to maximum until the back end temperature is under control
On wet process kilns, clear all personnel from firing floor

Preventive Measures
Avoid operating the kiln for more than 10 minutes when there is feed shortage
Establish and enforce maximum permissible operating limits for intermediate and/or exit gas
temperatures


HEAVY RAIN OR THUNDERSTORMS

Possible Effects and Dangers
On kilns that are exposed to elements;
Loss of coating and collapse of refractory lining
Thermal damage and warping of kiln shell
Possibility of power failure

Possible Actions
If storm occurs shortly after a kiln shutdown;
Jack (turn) kiln more frequently or continuously on auxiliary drive
Start auxiliary power generator in preparation for a possible power failure


SUDDEN, HIGH POSITIVE HOOD PRESSURE

Possible Reasons
ID fan failure
Large ring or build-up broken loose inside kiln
Instrumentation failure of cooler air flow, cooler stack damper, or ID fan control
Page 44 of 98

Steam explosion on wet-process kilns

Possible Effects and Dangers
All personnel on firing floor is in danger
Thermal damage to equipment on firing floor and hood
Danger of backfire in coal system

Possible Actions
Immediately clear all personnel from firing floor
Immediately reduce fuel rate to minimum and increase ID fan speed
Reduce cooler air flow rates into under grate compartments
Open cooler excess air damper manually


OVERHEATED KILN BEARINGS

(Procedure needs to be approved by your Maintenance Department)
Slow down kiln speed near minimum 20 rph. Do not stop the kiln (bearing will seize)
Open reset door on top of bearing and pour in sulfur until noise stops
You can add also powdered graphite to the bearing lubricating oil
The sulfur must be poured on the shaft and not on the bearing casing
Keep a bag of sulfur near the control room location
Call the Maintenance Supervisor
Check if the oil heating is on or not, and stop it if it is in operation (breaker location must be known to
all)
Check if the water or glycol circulation is okay. If there is no circulation, open the water valve very slowly
If you cannot reach the Maintenance Supervisor, call for an Oiler and a Maintenance man
Install a water hose to get cold water in the bearing (not a close circuit loop)
Drain the oil and add new oil until the new oil has reached its normal temperature (below 120
o
F/50
o
C
you should have a temperature gauge showing the oil temperature on each bearing)
Temperature sometimes requires from 6 to 12 hours to reach 120
o
F/50
o
C
Page 45 of 98

Type of oil to use for the bearings to be confirmed by your maintenance department


KILN HAZARDOUS CONDITIONS

Shooting Rings with Gun
Do not allow any employees other than the gun crew on the firing hood during ring shooting
Do not tamper with the ammunition
Keep all live ammunition locked up and away from the firing floor when not in use
Permit only experienced and trained persons to operate the kiln gun
Use ear muffs when firing gun
Cotton stuffed in the ear is not adequate
Clean gun at frequent intervals and do not attempt to fire an apparent defective gun
If kiln has no chain section, keep all persons away from the kiln back end and rope this area off
before shooting

Clinker, Fuel Oil and Coal Dust Spills
Clean up spills immediately
Provide adequate clean-up cans and facilities for easy removal of spills
Initiate repair action when spills are caused by leaks that can be repaired

Gas, Fuel Oil, Coal and Steam Leaks in Fuel System
Report any gas odor on the firing floor immediately to the shift supervisor
Provide for periodic inspection of fuel and steam lines and system to detect leaks and other
defects as a preventive measure against major breaks in the system

Burner Hood, Porthole and Cooler Doors
Do not allow anyone to look into the burning zone while the kiln is on operation unless
approved safety equipment for viewing is used
Use proper protective clothing when working near open burner hood and cooler doors while the
kiln is in operation
Page 46 of 98

Instruct all persons to stay clear of the portholes whenever the hood pressure is temporarily on
the positive side

Relining the Kiln with Refractory Bricks and Materials
Use protective screen when working under loose refractory and coating, if no alternate
procedure is possible
Any employee working inside the kiln should have positive means, such as locking out the kiln
drive with his own lock, to assure that the kiln cannot be started while he is inside
Have proper posture and steady footing when lifting bricks or scaling coating
Do not work underneath the burner hood bridge while material is being hauled in and out of the
kiln
Do not test run cooler fans when workmen are inside the kiln
Do not run ID fan when workmen are at kiln rear or in chain section

Working Near or on Dust Collecting Equipment
Wear extra protective clothing to guard against burns from hot dust
Wash skin thoroughly with clear water after contact with alkaline dust
Have a second workman as safety man standing by whenever working under or in bins or
hoppers containing material
Do not allow workmen to work inside hopper without being properly secured on safety lines and
belts
When working on plugged flue hangers, be constantly on guard against potential dust flushes
and cave in of overhanging materials

Backfire and explosion During Kiln Light-up
Open either one cooler or burner hood door before lighting fire in kiln
Secure proper draft in kiln before fire is lighted (very important)
Do not allow unauthorized person to stand near the burner hood during light-up
Stay clear of burner hood ports when igniting the fuel
Avoid excessive fuel flow on initial light-up of flame
Start the primary air fan before opening the fuel valve
Page 47 of 98

When firing coal, make sure that no coal dust spills are present on firing floor, around coal
feeder, or in the primary air pipe

Setting any Kiln Machinery into Motion During Start-up
Make sure all persons are clear of kiln equipment before each unit started
Sound horn to signal startup
Inspect all circuit breakers before the startup to make sure that all safety tags and locks have
been removed
Make sure all machine guards are in place before any equipment is started

Relining the Kiln with Refractory Bricks
Construct a proper bridge across the burner hood from firing floor to kiln nose
Inspect coating and remove loose overhangs before passing underneath
Keep all unauthorized personnel out of kiln interior



KILN OPERATION SECTION

KILN OPERATION TECHNIQUES

There are Three Common Techniques for Burning Clinker in a Rotary Kiln

Maintain a constant kiln speed, and vary the fuel rate to counteract the temperature changes in
the burning zone
Maintain a constant fuel rate, and vary the kiln speed to hold the burning zone temperature at
the desired label
Vary the kiln speed, the fuel rate or both to maintain the desired burning zone temperature

These techniques have one error in common. They show concern only for the burning zone
temperature.
Page 48 of 98


Unfortunately, many kiln operators think that this is good enough, reasoning that, as long as good-
clinkers are produced, what more is necessary? The fallacy of this reasoning lie in the fact that ideal
stable kiln conditions can be obtain faster and more economically when equal consideration is given to
all zones in the kiln and not the burning zone alone.

The process of clinker burning, therefore the process of rotary kiln control starts not at the place where
the feed enters the burning zone but at the point where feed enters the kiln.
The Proper Operation Technique is:

Vary the kiln speed, the fuel rate and the induced draft fan in any combination to maintain the proper
burning zone temperature and maintain a constant back-end temperature for a given rate of feed. This
technique is called; Burning a kiln from the rear.
By doing so, you prevent the variations instead of reacting to them when they reached the burning
zone.
If you stabilize the kiln back-end temperature you will be able most of the time to overcome the burning
zone temperature variations mainly by using the fuel input to the kiln and the ID fan speed.

In long wet and dry kilns, kiln speed variations should be avoided as much as possible in normal
operation as it create variations in the material loading of the kiln and eventually could lead to the kiln
into an upset.

If kiln speed variations is to be used, then they should be small (1 to 3 rph) keeping in mind that the
material load of the kiln will be more or less +/- 2 hours later as it will reach the burning zone, (kiln
retention time).
However, speed variations must be used on pre-calciner kilns to control the burning zone temperature
as the calcinations rate or the feed preparation is done by the fuel input on the pre-calciner burners.

The feed/speed ratio must remain constant all the time once the perfect loading of the kiln has been
found. Speed/feed ratio should not be changed to control the kiln.

Page 49 of 98


BURNING ZONE EVALUATION

The burning zone condition can be estimated from the colors observed in the hottest part of the flame.
An orange-yellow color is normal.
When looking into burning zone, one will observe a sharp color change of the lowest part of the feed
bed under the flame from dark to bright.

This point in burning zone is of great importance to the operator as it is the earliest indication when the
burning zone tends to warm up or to cool down.

In normal operation, the position of the dark feed remains stationary approximately one quarter of the
distance into the flame. This point should be used at the main indicator for evaluation of the burning
zone.

If the dark feed move further under the flame (towards the front of the kiln) the burning zone is cooling
down.

If the dark feed shifts in the direction of the kiln rear the burning zone is warming up.

The position of the dark feed can feed can move because of changes in the flame shape, the feed
loading of the kiln or if the feed to kiln is harder to burn. Any change in the position of the dark feed
must be viewed in the light of all of these influences.

The operator must be able to see the dark feed whenever he looks inside the kiln and he must regulate
the operation of the kiln so as to achieve this;

A slow shifting of the dark feed in either direction can usually be counteracted by a small change in the
fuel input rate in order to keep the feed in its proper place.

Page 50 of 98

If it become necessary to counteract the condition in which the feed has slipped too far under the flame
than the kiln speed should be varied to restore the dark feed position to the proper location.


STABLE KILN TEMPERATURE PROFILE

When there is no movement (up or down) of the dark feed, and no changes were made on the kiln
speed, the fuel rate and the ID fan speed for the last 2 hours, and the back-end temperature has
remained stable than;

The kiln temperature profile should be considerately satisfactory and the kiln system stable,
Then the burning zone should be considered as set point for this kiln feed;
When the burning zone as reached this condition than the related back-end temperature, and gas chain
temperature should be considered as set point also for this kiln feed.


TARGET SET POINT AND OPERATION REFERENCES

Whenever the operator has achieved a perfect and stable temperature profile on the kiln system, the
value of the following sensors should be taken as references set point for future operation and are:
Back-end temperature
Gas chain temperature
Material chain temperature
Kiln amps
Burning zone temperature
NOx value
And these values need to be correlated to the main controllers on the kiln which are:
The feed rate to the kiln (and the type of clinker produced)
The kiln speed
The ID fan speed
The fuel rate to kiln
Page 51 of 98

The oxygen level
References and set point for operation need to be established on each type of clinker produced and this,
at the maximum feed rate on each kiln system.
Also a copy page of the kiln operation should be taken.
With all these references, the operator has all the tools to make an optimized kiln operation.

BACK END TEMPERATURE CONTROL

Back End Temperature is controlled principally by 3 factors;
ID fan speed - Change in kiln exit draft (oxygen level)
Fuel rate - Causing changes in heat input in kiln
Feed rate - From feed variations in feed ratio, kiln speed, or dust return rate to kiln
Back End Temperature control goes hand in hand with oxygen, fuel rate and burning zone control. As a
matter of fact, whenever the operator makes an adjustment in any one of the main control variables, he
has to consider the reaction that will take place in all regions of the kiln. Of these, the ID fan speed and
the fuel rate are the usual causes for changes in back-end temperature, as the feed rate should remain
constant.


THE THREE BASIC VARIABLES

Variable Conditions in the kiln are indicated by:

The Burning Zone Temperature or dark load position, NOx signal, and kiln amps level which has
the dominant influence on the clinker quality
The Back-End Temperature or the gas chain temperature which are the principal controls on the
operation stability
The Percentage of Oxygen in the exit gas, which governs the combustion and the fuel efficiency

Page 52 of 98

In most conditions, except for the emergencies or upset conditions, the operator will find that these
three variables can be maintained within reasonable limits by means of adjustments of one or more of
the 3 basic controls.


TARGET RANGES FOR THE THREE VARIABLES

Ranges for the Three Variables
For the kiln operation, it is necessary to establish target ranges for the three variables. This information
will be supplied by the past experience and depend on the raw mix composition, clinker type and other
factors.
These ranges has to be established where these variables can safely be permitted to fluctuate without
upsetting the kiln operation.

Examples of Values which have been established:
target range limits
Burning Zone Temperature 2800
o
F (1550
o
C)
+/- 50
o
F
(+/- 50
o
C)
2750
o
F to 2850
o
F
(1500
o
C to 1600
o
C)
Back-End Temperature 1450
o
F (800
o
C)
+/- 20
o
F
(+/- 20
o
C)
1430
o
F to 1470
o
F
(780
o
C to 820
o
C)
Oxygen Percentage 1.2% +/- 0.8% 0.4% to 2.0%


THE THREE BASIC CONTROLS

Fuel flow to the burner
Change in the kiln speed
Change in the speed of the ID fan

The operator needs to use one or all of its three controllers to keep these variables inside their limits.
The operator must be alert and correct any out of range conditions as soon as it reaches the limits of
tolerance.
Page 53 of 98

Correction should be made promptly, but care must be exercised to avoid overreacting as this could lead
the kiln to an upset.


THE 27 CONDITIONS (KURT E. PERAY)

Because any of these variables can be within, below or above the allowable range, there are 27 possible
conditions that will be encountered by the operator.
These are shown graphically in the following figure. Note that a case number has been assigned to each
condition as an aid to identification. This chart should be used by the operators to understand the logic
of good kiln operation procedures where the Back-End Temperature, the Burning Zone Temperature
and Oxygen level were all taken in consideration in order to make a logic correction to an out of range
variable.
Case Condition Action to be taken Reasons
1
BZT low
Ox low
BET low
When BZT is drastically low,
a) reduce kiln speed
b) reduce fuel rate
When BZT is slightly low,
c) increase ID fan speed
d) increase fuel rate

a) to increase BZT and BET
b) to move Ox percentage into range

c) to raise BET and Ox
d) to raise BZT and Ox into range
2
BZT low
Ox low
BET OK
a) reduce kiln speed
b) reduce fuel rate
c) reduce ID fan speed
a) to raise BZT
b) to raise Ox percentage into range
c) to maintain BET
3
BZT low
Ox low
BET high
a) reduce kiln speed
b) reduce fuel rate
c) reduce ID fan speed
a) to raise BZT
b) to increase Ox
c) to reduce BET
4
BZT low
Ox OK
BET low
When BZT is drastically low,
a) reduce kiln speed
When BZT is slightly low,
b) increase ID fan speed
c) increase fuel rate

a) to raise both BZT and BET

b) to raise BET and Ox
c) to raise BZT
5
BZT low
Ox OK
BET OK
When BZT is drastically low and
Ox is in lower part of range,
a) reduce kiln speed
b) reduce fuel rate
c) reduce ID fan speed


a) to raise BZT
b) to raise Ox
c) to maintain BET
Page 54 of 98

When BZT is slightly low and Ox
is in higher part of range,
d) increase fuel rate


d) to raise BZT
6
BZT low
Ox OK
BET high
When BZT is drastically low,
a) reduce kiln speed
b) reduce fuel rate
c) reduce ID fan speed
When BZT is slightly low and Ox
in higher part of range,
d) reduce ID fan speed

a) to raise BZT
b) to raise Ox
c) to lower BET


d) to reduce BET and raise BZT
7
BZT low
Ox high
BET low
When BZT is drastically low,
a) reduce kiln speed
b) reduce ID fan speed
When BZT is slightly low,
c) increase fuel rate
a) to raise both BZT and BET
b) to maintain BET

c) to raise BZT and lower Ox & BET.
BET should be rising also, if not
keep increasing fuel rate and ID
fan speed
8
BZT low
Ox high
BET OK
When BZT is drastically low,
a) reduce kiln speed
b) reduce ID fan speed

When BZT is slightly low,
c) increase fuel rate

a) to raise BZT
b) to maintain BET. If Ox is still
available after this move, increase
fuel also
c) to raise BZT and lower Ox
9
BZT low
Ox high
BET high
When BZT is drastically low,
a) reduce kiln speed
b) reduce ID fan speed
c) increase fuel rate
When BZT is slightly low,
d) reduce ID fan speed

a) to raise BZT
b) to lower BET and Ox
c) to raise BZT and lower Ox

d) to raise BZT and reduce BET & Ox
10
BZT OK
Ox low
BET low
a) increase ID fan speed
b) increase fuel rate
a) to raise BET and Ox
b) to maintain BZT
11
BZT OK
Ox low
BET OK
a) decrease fuel rate slightly a) to raise Ox
12
BZT OK
Ox low
BET high
a) reduce fuel rate
b) reduce ID fan speed
a) to increase Ox
b) to lower BET and maintain BZT
13
BZT OK
Ox OK
BET low
a) increase ID fan speed
b) increase fuel rate
a) to raise BET
b) to maintain BZT
14
BZT OK
Ox OK
BET OK
None, however do not get
overconfident

15
BZT OK
Ox OK
When Ox is in upper part of
range,


Page 55 of 98

BET high a) reduce ID fan speed
When Ox is in lower part of
range,
b) reduce fuel rate
c) reduce ID fan speed
a) to reduce BET


b) to raise Ox
c) to lower BET and maintain BZT
16
BZT OK
Ox high
BET low
a) increase ID fan speed
b) increase fuel rate
a) to raise BET
b) to maintain BZT and reduce Ox
17
BZT OK
Ox high
BET OK
a) reduce ID fan speed slightly a) to lower Ox
18
BZT OK
Ox high
BET high
a) reduce ID fan speed slightly
b) reduce fuel rate slightly
a) to lower BET and Ox
b) to maintain BZT
19
BZT high
Ox low
BET low
When BZT is drastically high,
a) increase kiln speed
b) increase ID fan speed
c) reduce fuel rate
When BZT is slightly high,
d) increase ID fan speed

a) to avoid overheating BZT
b) to raise BET and Ox
c) do

d) to lower BZT and raise BET & Ox
20
BZT high
Ox low
BET OK
When BZT is drastically high,
a) increase kiln speed
b) decrease fuel rate
c) increase ID fan speed
When BZT is slightly high,
e) increase ID fan speed

a) to avoid overheating
b) to lower BZT
c) to increase Ox and maintain BET

d) to lower BZT and raise Ox
21
BZT high
Ox low
BET high
When BZT is drastically high,
a) increase kiln speed

b) reduce fuel rate
When BZT is slightly high,
c) decrease fuel rate

a) to lower BET and avoid
overheating
b) to lower BZT and increase Ox

c) to lower BZT, BET and increase Ox
22
BZT high
Ox OK
BET low
When BZT is drastically high,
a) increase kiln speed
b) increase ID fan speed
c) reduce fuel rate
When BZT is slightly high,
d) increase ID fan speed


a) to avoid overheating
b) to raise BET
c) to lower BZT

d) to raise BET and lower BZT (see
note A)
23
BZT high
Ox OK
BET OK
When BZT is drastically high,
a) increase kiln speed
b) decrease fuel rate
c) increase ID fan speed
When BZT is slightly high,
d) reduce fuel rate

a) to avoid overheating
b) to lower BZT
c) to maintain BET

d) to lower BZT (see note A)
24
BZT high
Ox OK
When BZT is drastically high,
a) increase kiln speed

a) to avoid overheating & lower BET
Page 56 of 98

BET high b) decrease fuel rate
When BZT is slightly high,
c) decrease fuel rate
b) to lower BZT
c) to lower both BZT and BET (see
note A)
25
BZT high
Ox high
BET low
When BZT is drastically high,
a) increase kiln speed
b) increase ID fan speed
When BZT is slightly high,
c) increase ID fan speed

a) to avoid overheating
b) to increase BET and lower BZT

c) to raise BET & lower BZT (note A)
26
BZT high
Ox high
BET low
When BZT is drastically high,
a) increase kiln speed
b) increase ID fan speed
c) decrease fuel rate
When BZT is slightly high,
d) reduce fuel rate

a) to avoid overheating
b) to maintain BET
c) to reduce BZT

d) to lower BZT (see note A)
27
BZT high
Ox high
BET high
When BZT is drastically high,
a) increase kiln speed
b) decrease fuel rate
When BZT is slightly high,
c) decrease fuel rate
d) decrease ID fan speed

a) to lower BZT and BET
b) do

c) to lower BZT
d) to lower BET (see note A)
NOTE A: If the % O
2
increased during this adjustment, disregard it until temperatures are brought under control.



KILN UPSET CONDITIONS SLOW DOWN

Kiln cannot operate in a stable condition at all times and it will eventually get colder.

Sometimes heavy rush of feed might end up too far under the flame (halfway under the flame).

Operator must then decide if he will be able to control the heavy feed load only by increasing the fuel
flow, or if he needs to reduce the kiln speed.
The determinant factors to be considered are the oxygen level, back-end temperature, movement of the
feed rush, and conditions in the cooler.

Assuming that it is impossible to maintain the same kiln speed, the operator must determine how much
the kiln speed can be slowed down depending on the magnitude of the push.

Page 57 of 98

Only experience can tell the operator how much the kiln has to be slowed down.

In those cases the following rules apply all the time;

When in doubt, the kiln speed reduction should be greater than required. This will help to
overcome the problem faster.

Never allow the raw, unburned feed to enter into the cooler, even if it means that the kiln must
be stopped and rotated on turn or the auxiliary drive.

As soon as the kiln has been slowed down, the operator must;

Try to keep the back-end temperature within acceptable limits variation (i.e. 75 to 100
o
F).

Cut down the fuel flow to maintain the oxygen level above 0.5% and to keep back-end
temperature inside the limit range.

Evaluate the cooler conditions, grate speed, grate temperature, inlet temperature of gravel bed
collection system and secondary air temperature.

Often, the cooler will have to be switched on manual mode to protect it to become overheated
as often regulation of cooler are made for small variations only.

As the kiln is on slow speed, it is necessary to determine when the speed can be increased back again.
In that case, the oxygen level is the main factor to look at.
Try to keep the same values on the fuel flow and ID fan speed in order to observe the O
2
variations.
When O
2
level increases, the burning zone is warming up.

As soon as the oxygen level start to increase, increase the kiln speed slowly i.e. +/- 3 rph if the
burning zone is still dark and very dusty.

Page 58 of 98

Observe the reaction of the O
2
level if it keeps on raising.

If so, increase kiln speed by 3 rph at every 10 minutes, and keep on increasing as long as the
oxygen level does not drop.

Keep fuel flow always one step ahead of normal operation level, (i.e. when rotation speed is at
24 revs, set fuel flow for 27 revs), and ID fan speed accordingly.

Stop increasing kiln speed approximately 1 to 2 hours after initial slow speed in order to
overcome any upset in the material load of the kiln created by the speed variation.

Restart increase the kiln speed after reception of material from slowdown is over.

Kiln speed increase should be reduced around 80 revs as we are getting near full production (i.e.
2 revs at every 20 minutes).

When full production has been reached (i.e. 85 revs) the fuel flow must be kept one step higher
than normal for at least 2 more hours, and then it must be cut down slowly following the normal
operating procedures to get the load at the end of the flame again.

A slowdown made in time and at proper speed will requires about 20 minutes before to restart to
increase the kiln speed again (as O
2
start to go back up).

Usually, the kiln should be back in full production about 4 hours after the slowdown was made.

Slowdown Example:

revs t/h Fuel flow ID fan speed O
2
Operation
86 93 102 m
3
/h 530 rpm 1.5% Normal
66 72 85 m
3
/h acc. O
2
level 0.7 Slowdown
36 40 50 m
3
/h acc. O
2
level 0.7 slowdown
Page 59 of 98




NORMAL OPERATING PROCEDURES ON SHIFT

Take Over of Shift by Operators

Check:
Visual inspection of burning zone, look for dark load
Oxygen level and trend
Back-end temperature and trend
Kiln amps and trend
NOx signal and trend
Kiln speed
Kiln feed indicator
Secondary air temperature and trend
Clinker load on grate in cooler
Cooler fans under grate pressure
Kiln draft and hood pressure
Gravel bed filter or DC temperature
Water spray and precipitator

Then an evaluation of the kiln and burning zone state need to be done in order to compare actual
settings with the target value and limit ranges established before.

Wait at least 30 minutes before changing any values, unless there is an emergency condition in order to
evaluate if the kiln is warming up, cooling down or stable.


PLAN OF ACTION

Page 60 of 98

If the burning zone is hot (not drastically hot) and the kiln is stable
Decrease fuel flow by 3%
Then decrease ID fan speed to keep the same O2 level
Wait approximately 20 min (retention time of the burning zone) to see the reaction of your
move
Then repeat the same procedure again or stay there if dark load is moving in position or if the kiln amps
are dropping.

Repeat the operation until you get;
The dark load at the right position
The kiln amps inside its target range
The kiln gas temperature and back-end temperature inside their target range

If burning zone is cold (not drastically cold)
The same approach is to be done but in reverse

This procedure should be done on each shift in order to get the best kiln condition and the best heat
consumption possible at all times.

Whenever the dark load, the kiln amps and the kiln back-end temperature are back inside their target
range, then the 27 conditions procedures should be done again to maintain the kiln back-end and the
burning zone temperature on set point and the kiln temperature profile stable.



OXYGEN LEVEL IN AUTOMATIC MODE

When the perfect temperature profile balance has been reached, we can eventually set the oxygen level
on automatic (looped to the ID fan speed). This will allow the gas flow in the kiln to be constant and will
help to maintain the kiln system stability.

Page 61 of 98

Theoretically speaking, as we reach this situation, no more moves on the fuel rate, feed rate and kiln
speed need to be done and the kiln should remain in balance until an upset on the material load or a mix
change creates an upset again.

So the oxygen level control should be set on automatic whenever the temperature profile in kiln is
satisfactory. Every time this is not so or the kiln is slightly upset, the oxygen should remain in manual
and used to establish a good temperature profile inside the kiln.



KILN START-UP AND SHUTDOWN PROCEDURES


KILN PREHEAT

Light-Up Flame Example (gas)
1) Call the gas company to tell them that you are going to light up
2) Open one side of precipitator (inlet and outlet damper)
3) Start dust handling system on the side of precipitator in use with dust going to the ground (to
avoid plugging the circuit with moist material)
4) Start up ID fan at minimum speed (damper closed)
5) Open ID fan damper at 10%. Use a rag in front of kiln door to evaluate suction in the kiln and
adjust damper to obtain proper suction
6) Start primary air fan with damper closed
7) Install torch under burner pipe
8) Set natural gas to obtain approximately 13 m
3
/min (450 ft
3
/min)
9) Slowly open manual valve on gas line
10) Adjust primary air damper, primary and secondary gas pressure, and ID fan damper for best
flame possible
11) If flame goes out, make sure to purge the air inside the kiln before any attempt to try lighting up
again
Page 62 of 98

12) Dont turn the kiln for the first 2 hours
13) Start nose ring fan one hour after the flame on


PRE-HEAT or Drying of the Refractory Lining


General Information:
The pre-heat period last around 12 hours. A minimum of 8 to 12 hours is necessary
The reference temperature during this period should be the kiln feed end temperature
The target temperature should be approximately 300
o
C or 575
o
F at the precipitator inlet
Start kiln rotation (1/4 turn) 2 hours after flame on
After make turn every 30 minutes until the end of pre-heat period


If New Castable was Installed:
Pre-heat period could take as long as 36 hours depending on the location and the quality of the castable
installed and could be divided in three periods as follows:

First Period:
For 12 hours with gas flow of 13 m
3
/min or 450 ft
3
/min
Do not exceed 170
o
C or 340
o
F at the filter inlet during this period
Two hours after the flame on, make turn every 30 minutes during the balance of this period

Second Period
For 12 hours, increase the precipitator inlet temperature so it could reach 230
o
C or 450
o
F
Make turn every 30 minutes during this period
Third Period:
For 12 hours, increase the precipitator inlet temperature to reach 300
o
C or 575
o
F
Make turn every 30 minutes during this period

Page 63 of 98


HEATING (To reach temperature ready to put feed on)

General Information:
The reference temperature is the gas chain inlet temperature
The target temperature should be approximately 40
o
C or 105
o
F lower than the normal operation
temperature
The rate of increase of the temperature should be approximately 50
o
C or 125
o
F per hour

The temperature increase per hour should be done according to the following:
Length of refractory installed;
Complete kiln: 35
o
C or 100
o
F per hour increase
Repaired burning zone: 50
o
C or 125
o
F per hour increase

Kiln rotation during heating:
1) turn every 10 minutes for 2 hours
2) Continuous turn on auxiliary drive for 2 hours
3) Rotation at 0.5 or 30 revs for 1 hour
4) Rotation at 0.7 or 42 revs until 15 minutes before feed on
5) Rotation at 1.0 or 60 revs 15 minutes before putting feed on
Oxygen level during this period should be kept between 7 to 10% in order to increase the back end
temperature to avoid the burning zone to get overheated. Burning zone should be pink in color.

The cooler system is usually down, leaving only the nose ring fan and the primary air fan running

During this period, it is most important to keep the greasing system on the kiln drive running

As soon as the kiln is running continuously, start cooling fans on the burning zone


Expansion of the Kiln and Tire
Page 64 of 98

Heating rate in large diameter kiln (>14) should not be higher than 50
o
C or 125
o
F per hour to
allow both tire and shell to expand at proper rate

Clearance between tire and shell should be monitored during start-up

The larger the diameter of the kiln, the more care has to be taken to get it running


FEED ON KILN

General Information:
Feed rate is approximately 50% of normal feed rate
Feed rate increase of about 5 tons every hour
Kiln speed should be maintained at 1.0 rpm or 60 revs until the material reaches the burning
zone (to get material in burning zone quick)
Target for chain inlet temperature; 800
o
C (1472
o
F) or 40
o
C (100
o
F) below normal operation
temperature
Set ID fan speed to maintain about 3% the oxygen level
Start high voltage on precipitator
Start remaining items on cooler system (all cooler fans with dampers set as required)
Maintain those settings until the start-up reactions occurs (push should take +/- 2 hours)
In order to promote good coating formation in the burning zone, stabilize the kiln at 1.1 rpm or
66 revs at about 70 tph for 24 hours
After this period, take the kiln up to optimum operation level with normal operation procedures


KILN START-UP PROCEDURES (AFTER BRICK JOB)

Preparations:
72 hours before light-up, call the gas company to tell them the date and the hour of the light-up
4 hours before light-up, make dry run on all equipment
Page 65 of 98

Check burner pipe and its installation
Center the burner pipe, or adjust 1 down and 1 towards the load (make marks outside the kiln
for the burner pipe position reference)
Check fuel on auxiliary drive
Take locks off on kiln equipment sets
Take off wood shims on kiln rollers

Pre-heat:
Start kiln section on CRT
Open one side of precipitator (outlet and inlet damper)
Start the dust handling on the side of the precipitator in service, with the dust on ground to
avoid plugging the circuit
Start-up ID fan at 125 rpm or minimum speed, damper closed
Open ID fan damper at 10%
Start primary air fan, damper closed
Install a torch under burner pipe
Set natural gas in control room at 13 m
3
/min or 450 ft
3
/min
Open manual gas on gas line
Open supervisory cock valve near burner pipe
Adjust primary air, primary and secondary gas and ID fan to get the best flame
One hour after, start nose ring fan and make no kiln rotation for the first 2 hours
The pre-heating period should last around 12 hours. A minimum of 8 to 10 hours is necessary. The
temperature at the inlet of the precipitator must reach 300
o
C or 575
o
F.

Special pre-heating after castable has been installed near the burning zone

First Period:
For 12 hours with gas flow of 13 m
3
/min or 450 ft
3
/min
No kiln rotation for the first 2 hours
Kiln rotation at turn every 30 minutes after 2 hours
Try not exceed 170
o
C or 340
o
F at the filter inlet during this period
Page 66 of 98


Second Period
For 12 hours, increase the back-end temperature so it could reach 230
o
C or 450
o
F
Make turn every 30 minutes during this period

Third Period:
For 12 hours, increase the back-end temperature to reach 300
o
C or 575
o
F
Make turn every 30 minutes during this period



HEATING-UP

The reference temperature is the chain gas temperature
The rate of increase of the temperature should be approximately 50
o
C or 125
o
F per hour
The target temperature should be approximately 40
o
C or 100
o
F lower than normal operation
temperature
Draw a curve on chain inlet temperature chart, so you could follow the temperature increase
Increase progressively fuel and draft (open second precipitator chamber when required)
The burning zone should be kept in place and should be pink when the feed will be put on
During that heating period, the oxygen should be between 7 and 10%
Start the water spray to keep the back end temperature at 350
o
C or 660
o
F
Around 750
o
C or 1400
o
F, start kiln feed for 10 minutes for testing
Check if any clinker on cooler grate and when necessary start the clinker evacuation system
Start shell fan when kiln is turning on continuously
Start cooler fan #1 and #2 at minimum 30 minutes before kiln feed
When you reach 800
o
C or 1475
o
F at chain inlet temperature (T according to plant normal
operation temperature minus 40
o
C or 100
o
F), start feed



Page 67 of 98

FEED ON

Start:
Kiln feed at 45 tons/hr
Kiln speed at 1.0 rpm or 60 revs

Increase;
Kiln feed at 5 tons per hour
Fuel rate and ID fan speed accordingly (maintain fuel rate 1 step ahead of normal operation)

Start fan #3, #4 and #5 (damper closed) 15 minutes after feed is on

Start gravel bed filter or its equivalent

Put tension on kiln precipitator 15 minutes after kiln feed is on

Stabilize the kiln at 1.1 rpm or 66 revs/hr at about 70 tph feed rate for 2 hours to promote good coating
conditions in burning zone

When increasing kiln feed, adjust the pressure and fan flow on cooler fans

Check closely the clinker evacuating system

When there is a good load in the cooler put the cooler on regulation


Kiln turns during heating:

turn every 10 minutes for 2 hours
Continuous turn on auxiliary drive for 2 hours
Turn at 0.5 rpm or 30 revs/hr for 1 hour
Page 68 of 98

Turn at 0.7 rpm or 43 revs/hr until 15 minutes before putting feed on
Turn at 1.0 rpm or 60 revs/hr 15 minutes before feed on



EXAMPLE OF HOW TO START KILN IF PRE-HEAT IS REQUIRED (Load in kiln)

If pre-heat is required (Function of burning zone and gas chain temperature)
Open dampers on precipitator (both side)
Fuel rate at 44 m
3
/min or 1554 ft
3
/min
ID fan speed at 25 rpm (minimum speed)
ID fan damper position according to O
2
level (5% maximum)
Maintain these settings until temperature reach on gas chain temperature at 850oC or 1562oF (normal
kiln operation temperature).

Kiln rotation varied according to gas temperature as follows:
If;
Chain Gas Temperature Rotation Fuel Rate
750 to 930
o
F turn every 20 minutes 44 m
3
/h or 1553 ft
3
/min
930 to 1110
o
F turn every 15 minutes 50 m
3
/h or 1766 ft
3
/min
1110 to 1300
o
F turn every 10 minutes 57 m
3
/h or 2013 ft
3
/min
1300 to 1562
o
F turn every 5 minutes 63 m
3
/h or 2225 ft
3
/min

Then start the;
Kiln at 60 revs
Feed at 63 tph
Fuel at 88 m
3
/min or 3108 ft
3
/min
ID fan speed at 350 rpm and to maintain O
2
near 4%
Start burning zone cooling fans

Page 69 of 98

Wait at this setting to receive the material and then increase slowly like normal procedures but always
maintain on fuel and ID fan speed settings one step ahead.
During this period, the nose ring fan is on.
The primary air fan is on with normal setting.
The cooler fans #1 and #2 on cooler are running.
Grates, clinker circuit and gravel bed filter are running.

Guidelines:
For a shutdown less than 5 hours, warm-up period should be around 1.5 to 2 hours.
For a shutdown between 5 to 12 hours, warm-up period should be around 4 hours.



EXAMPLE OF HOW TO RESTART IF NO PRE-HEAT IS REQUIRED

Start-up speed is related to the gas chain temperature of the kiln and burning zone aspect.

Start-up could be as follows:
If;
Chain Gas Temperature Rotation Rotation Fuel Rate
1435
o
F 60 revs 65 tons/hr 3110 ft
3
/min
1475
o
F 66 revs 70 tons/hr 3425 ft
3
/min
1508
o
F 72 revs 76 tons/hr 3745 ft
3
/min
1545
o
F 75 revs 79 tons/hr 3885 ft
3
/min
1580
o
F* 78 revs 82 tons/hr 4025 ft
3
/min
*1580
o
F being the normal operation temperature
Adjust draft and fuel as required.
After material reception, increase according to normal procedures but keep 1 step ahead on fuel and ID
fan settings for 2 hours after you reach normal production level (retention time of material in burning
zone).

Page 70 of 98

This procedure is to be developed in order to restart a kiln faster and having less perturbation in the
material load of the kiln (long dry and wet kilns).



KILN SHUTDOWN (General Information)

There are many reasons why kiln must be shutdown periodically and in most cases, the operator must
decide when an immediate unscheduled shutdown of the kiln system is required. There is often not
enough time available in such situation to weigh or discuss the merits of a shutdown because a few
minutes of delay could lead to major equipment damage.

So clearly, an operator should be fully trained in what to do and what to do if such situation occurs.

Written standard procedures to cover these situations should be at the disposal of the operators to
allow them to review those procedures periodically.


COOLING PROCEDURES

In case of a shutdown, slow cooling of the refractory must be ensured.

The Stacks Registers:
Must be kept shut for a sufficient period of time
Cooling schedule should provide gradual cooling of the burning zone refractory at a maximum
temperature rate of 100
o
C (212
o
F) per hour
For smaller kiln, i.e. diameter < 13, maximum rate is 100
o
C or 212
o
F
For larger kiln, i.e. diameter > 13, maximum rate is 75
o
C or 167
o
F

The ID fan;
Should be shutdown immediately as soon as fire is cut off
Page 71 of 98

Should not be used for forced cooling at least for the first 12 hours after kiln shutdown
This is an absolute must on long dry and wet process kilns equipped with internal heat
exchangers such as chain
The ID fan inlet damper should also be closed completely for at least 12 hours

During short shutdown;
The kiln back-end should be closed completely for at least 12 hours

During short shutdown;
The kiln back-end should be closed completely to avoid hot gases to escape from kiln

Hood Pressure:
Flow adjustments on the cooler fans have to be made to avoid the kiln hood to get on to high
pressure
The hood pressure set point should be set slightly on the positive side to prevent air from
burning zone to escape through the cooler exhaust fan


KILN ROTATION SCHEDULE

The kiln must be rotated on a regular schedule to insure uniform cooling, as the feed bed and the
refractory underneath it, take more time to cool down than the refractory wall exposed to the kiln
gases.

Kiln Rotation for Short Maintenance Repair
turn every 5 minutes 4 times during 20 minutes
turn every 10 minutes 4 times during 40 minutes
turn every 15 minutes 8 times during 2 hours
turn every 30 minutes 8 times during 4 hours
turn every 60 minutes until the end ----------------

Page 72 of 98

If it is Raining,
Continuous rotation should be done on the auxiliary drive or on main drive at minimum speed

Kiln Rotation for Long Kiln Shutdown (brick lining repair)
Before:
Stabilize kiln rotation at 1.0 rpm or 60 revs before shutdown (flame still on)

Then:
Maintain continuous rotation at 0.6 rpm or 36 revs during 30 minutes (flame is off)
Maintain continuous rotation at 0.5 rpm or 30 revs during 2.5 hours
Maintain continuous rotation at 0.4 rpm or 24 revs during 1 hour
Maintain continuous rotation at minimum speed on auxiliary drive for 1 hour

Then:

If it is raining, continuous rotation should be done on the auxiliary drive or at minimum speed on main
drive.

Shutdown for long periods also included purging of the following:
Fuel firing system
Feed system
Dust system from precipitator or dust collector system
Dust system of conditioning tower
Clinker from cooler system


BURNER PIPE AND HOOD PROTECTION

The burner pipe must be protected as the hood and the kiln discharge area remains at high temperature
for several hours after the fire has been cut off.
Page 73 of 98

Some kilns are equipped with movable burner pipes to allow partial or full retraction of the burner.
Others have to rely on primary air fan to provide necessary cooling of the burner.
Primary air fan and nose ring fan should be running at least 10 hours after the flame has been cut off.


EMPTYING THE FEED FROM THE KILN

Emptying the feed from the kiln takes special skills and experience. It could be very dangerous and could
result directly in overheating conditions either at the back-end of the kiln, the burning zone, or the
cooler. So called chain and coal mill fires have occurred as direct result of attempting to burn out a
kiln.
Therefore, burning out a kiln is far too risky and should never be attempted.
As soon as the feed is cut off, the flame should be cut off.


KILN SHUTDOWN PROCEDURES (FOR BRICK JOB OR RED SPOT)

Time (- 2 hours) Cut down kiln speed at 1.0 rpm or 60 revs

Time (- 15 minutes) Cut off coal extraction from silo if required

Time (- 5 minutes) Cut off feed extraction from homo silo

Time (- 2 minutes) Cut off high voltage on precipitator

Time (0 hour) Cut off feed and purge circuit completely
Cut off fuel when system is purged

Time (+ 2 minutes) Stop ID fan
Reduce air flow under cooler

Page 74 of 98

Time (+ 4minutes) Close ID fan louvers slowly, or equivalent equipment
Adjust cooler fans to keep hood pressure slightly positive
Stop water spray system or any water system at back-end

Time (+ 6 minutes) Cut down kiln speed at 0.6 rpm or 36 revs
Reduce primary air fan (1000 Pascals or 10 mbars)
Put cooler system on manual mode
Reduce grate speed at 4 strokes per minute
Reduce fan #1, #2 and #3 at 50% of normal air flow
Reduce other fans according to gravel bed filter inlet temperature or
Other de-dusting system

Time (+ 10 minutes) Close main damper on precipitator, (line 1 & 2) or any equivalent
equipment
Keep the extraction of the dust system running
Keep nose ring fan running

Time (+ 15 minutes) Retract burner from kiln hood if possible if not keep primary air fan
running for cooling

Time (+ 30 minutes) Reduce kiln speed to 0.55 rpm or 33 revs
Pull water spray out of the kiln

Time (+ 1 hour) Reduce cooler fans #1, #2 and #3 to 25% of normal flow
Reduce other fans according to gravel bed filter inlet temperature or
other de-dusting system

Time (+ 1.5 hour) Reduce kiln speed to 0.5 rpm or 30 revs
Watch for unburned clinker and send it to proper location

Time (+ 2 hours) Stop cooling fans under kiln shell
Page 75 of 98

Readjust air flows under cooler
If possible, stop last fan according to filter inlet temperature

Time (+ 4 hours) Reduce kiln speed to 0.4 rpm or 24 revs

Time (+ 5 hours) Stop rotation with main motor
Start continuous rotation with the auxiliary drive
Stop extraction of dust on the precipitator or dust collector system

Time (+ 6 hours) Stop continuous rotation with the auxiliary drive
Make turn every 15 minutes (attention to greasing system in the main
kiln drive to be started in manual)

Time (+ 8 hours) Make turn every 30 minutes

Time (+ 10 hours) Stop nose ring fan and primary air fan
Time (+ 12 hours) Make turn every hour

Time (+ 15 hours) Stop cooler fans
Stop gravel bed filter system if required

Time (+ 16 hours) Open main damper on one side of the precipitator
Start the ID fan a few seconds with damper closed every hour

Time (+ 18 hours) Start ID fan a few seconds
Open ID fan damper at 10%

Time (+ 20 hours) Start ID fan a few seconds
Open ID fan damper at 25%
Open door on kiln hood

Page 76 of 98

Time (+ 22 hours) Start ID fan a few seconds
Open ID fan at 75%

Time (+ 24 hours) Close ID fan completely

Time (+ 26 hours) Start ID fan at minimum speed
Open ID fan at 10%

Time (+ 27 hours) Open ID fan at 30%

Time (+ 28 hours) Open ID fan at 50%

Time (+ 29 hours) Open ID fan at 75%

Time (+ 30 hours) Open ID fan damper completely
Stop kiln rotation completely
Start to open kiln hood front door
Make security on kiln system (lock procedures)
Start to clean cooler system
This shutdown procedure could also be used as an emergency shutdown on red spot.



CLINKER COOLER SECTION

COOLER

FUNCTION
a) The main function of the cooler is to recuperate the heat contained in the clinker coming from
the kiln as heat recovery from secondary, tertiary and to coal mill air is important for kiln
efficiency and fuel saving.
Page 77 of 98

b) The cooler must also lower the temperature of the clinker before it leaves so it can be safely
transported to the storage area
c) The clinker breaker at the cooler outlet reduce the clinker size so it can be transported on the
conveyor system

COOLER OPERATION
Cooling of the clinker material is accomplished by forcing ambient air upward through the material as it
is being conveyed through the length of the cooler by reciprocating action of the grates.
The clinker cooler is divided into two major areas, which are separated by the grate line. They are the
over grate area where the clinker is cooled down and where the hot gases are handled and the under
grate compartment where cooling air is blown into the system.
The grate line consists of many perforated grate plates arranged in overlapping rows. The alternate rows
are movable and are connected to a wheel mounted frame which is moved back and forth on its tracks
by a crank type drive that drives the grates their reciprocating motion. See figures 2 to 6.
In normal operation, the cooler is running in auto to keep a constant under grate pressure and air flow
under the second compartment in order to control the secondary air temperature.
However under upset conditions, the cooler must be switched on manual.

COOLER CONTROLLERS
In normal operation:
The speed of the grate change the residence time of the clinker inside the cooler (to control the
cooling rate of the clinker and to protect the grate to get overheated)
The air flow distribution under each compartment to maintain good heat recuperation and good
cooling of the clinker
In case of emergency: (such as a badly overheated cooler condition, the operator must always)
Decrease the kiln speed in order to reduce the clinker input to the cooler and control the heat
input


OPERATION OBJECTIVES

Page 78 of 98

To keep as much as possible:
The clinker temperature at the cooler discharge as low as possible (high temperature could
damage the clinker transport system)
The secondary air temperature as stable and as high as possible to get the best recuperation
from the clinker and improve the fuel efficiency of the kiln
To keep the depth of the clinker bed near 15 water gage in order to get good heat recuperation
from the clinker in cooler (according to fan capacity)
To keep the hood pressure always slightly negative
To set the cooler fans flow in such away to have enough capacity to get air through the clinker
bed and to insure proper cooling of the grates and the clinker load inside the cooler
Cooler settings should be such that bed grates, cooler drive unit, clinker crusher, cooler wall and clinker
conveyors system cannot become overheated.


RULE IN COOLER OPERATION

A fundamental rule on grate cooler is to never permit raw feed or extremely fine clinker to enter the
cooler as the cooler can become overheated and damage.
During kiln pushes, lower the kiln speed in order to reduce fine clinker input in the cooler.

Never run the kiln with positive pressure as this result in troubled kiln operating conditions as:
Fine clinker in nose ring resulting to wear of kiln seal
Viewing in kiln is unpleasant and unsafe
Could damage the optical equipment and the TV camera
Formation of rings and snowmen in cooler inlet can be attributed to positive pressure
Exception: One exception to this rule if ever very high temperature in cooler and if needed to introduce
sufficient air in cooler.


MAIN SENSORS

Page 79 of 98

The Main Sensors to Control the Cooler Operations are:
The fans flow for each compartment
The under grate pressures under grate #1 and #2
The secondary air temperature
The grate speed under grate #1 and #2
The clinker discharge temperature at the cooler outlet

Also Secondary Sensors as:
Grate temperature in #1 and #2 compartments
TV camera showing the cooler interior

Hood Draft
Control by regulation the excess air inside the cooler by the cooler exhaust fan damper
It maintains a constant pressure in front of the kiln
A good hood pressure regulation is important for the burning zone stability

Assuming other Factors Remain Constant:
An increase in the ID fan speed will lower the hood pressure
A decrease in the ID fan speed will increase the hood pressure
Also increasing the amount of air in cooler results in higher hood pressure

Under Grate Pressures and Air Flow Rates
The under grate pressure is govern by the following factors:
Depth of the clinker bed over the grate
Average particle size of clinker in the cooler
Amount of air flow into the cooler
Should be at 15 water gage (under 2
nd
compartment) to get good heat recuperation

Clinker Bed Depth
The depth of the clinker bed is controlled by the speed of the cooler grate
The faster the grate, the thinner becomes the bed and lower is the under grate pressure
Page 80 of 98

Because of the relation between the grate speed, bed depth and under grate pressure, it is
possible to maintain a constant under grate pressure by regulating the grate speed
It is usually done under the second compartment of the cooler because it is that location at the cooler
inlet where the clinker bed is more stable and give an early and good under grate pressure signal for the
automatic cooler control.


PARTICLE SIZE OF CLINKER

A critical factor in under grate reaction is the average particle size of the clinker in the cooler.
A fine clinker bed impose more resistance against air flow, when the under grate pressure
increase, the fan has to use more force to push the air through this kind of bed
Then the under grate pressure increase when the clinker gets finer because the smaller particles
impede the air flow through the bed
Therefore, the airflow rate is increased to restore the normal flow through the bed and the
clinker bed can become fluidized
A fluidized clinker bed is highly undesirable and dangerous, because the bed in such a state does
not move along properly in the cooler
On horizontal grate, the clinker tend to remain stationary and tend to build on top of the grates
and when sufficient weight has been acquired by the bed, it starts to move again
So the clinker cannot be properly cooled down and could choke off the airflow through the bed


OPERATION OF COOLER FANS

The air volume for cooler fans is most commonly carried out by means of fan outlet damper.
The fan speed is constant so it is necessary to change the position of the damper to reduce or to
increase the air moved by the fan.
Fan damper is normally open at 60% as necessary leeway is required to increase air flow.
Maximum air flow is when the fan damper reached about 88% open.
The air volume output is directly related to the under grate pressure.
Page 81 of 98

The fan must have sufficient capacity to provide necessary amount of air at maximum under
grate pressure.
The maximum operating under grate pressure needs to take into account the cooler fans
capacity.
Flow rate for each fan and under grate pressure set point need to be set on for a good cooler
operation.
The fan manufacturers provide performance curve for each compartment fan.

Fan Static Pressure
Fan static pressure is the total pressure developed by the fan, less the velocity pressure in the fan
discharge duct.
For practical purposes, fan static pressure in a cooler system is equal to the under grate pressure, and
the air flow is a function of this static pressure and the power applied to the fan. (Figure 7)
Whenever the under grate pressure exceed the limit of the fan, the flow decreases and less cooling is
taking place then the cooler could be damaged.


CLINKER AND AIR DISTRIBUTION

For proper cooling, it is essential that clinker is evenly spread over the width of the cooler so that the
bed offers a uniform resistance of the air passage through its width.

When clinker passes to one side of the cooler leaving a thinner bed on the other side, the air will
naturally seek a passage through the bed where it offers the least resistance.

So air passes through bed where it is least needed and little air passes where it is needed most.
Formation of snowmen at the cooler inlet is the prime cause of this condition.
Various devices as dead grate, spreaders or grate with their own air supply to spread the clinker
rapidly over the width of the cooler inlet are used to fight snowmen formation.
For proper air distribution and good cooler regulation, no air should freely pass from one cooler
compartment to another through leaks or other opening on the compartment walls.
Page 82 of 98

The under grate pressure is usually set that the highest pressure is found in the first
compartment, and the lowest in the last compartment.

Emergency High Clinker Temperature
Installed on the drag conveyor is this sensor to measure the clinker temperature at the cooler discharge.
If the clinker temperature is above 300
o
F (150
o
C), it will transfer the clinker to the emergency bin
automatically and will stay there until the desired temperature will come back. High clinker temperature
is caused by inadequate cooling of clinker in cooler.

Guideline:
In cooler normal operation, no red clinker should be seen passing the third compartment.


COMBUSTION SECTION

FLAME

A flame is a stream of gases at extremely high temperature (around 3500
o
F or 1930
o
C) where the
reactions of combustion of the fuel with secondary and primary air are taking place. Anything exposed
to such a flame is bound to receive heat from it.

Flame Evaluation
Should always be evaluated during stable kiln condition

Flame Length
Could refer to the distance between the burner tip and the end of the flame which is a total
flame length
It could also refer to a distance between the point where ignition of the fuel start and where the
reaction of fuel combustion ends
It is desirable to operate a kiln with the flame as short as possible, as long as it will not create
problem in front of the kiln, hood, nose ring and refractory (Figure #1)
Page 83 of 98


Flame Shape
Could be long and lazy as heat is released over a relatively long distance (example A)
Could be snappy as heat is released over a shorter distance (example C)

Flame Direction
The flame path is not a straight line
The flame has a tendency of lift upward toward the top resulting in uneven entrance of
secondary air, or mechanical condition of the primary air pipe nozzle
A good direction target for the flame could be 2A or 2B in Figure # 2, or one inch down center
line and one inch towards the material load

The flame temperature is related to:
1. Quality and type of fuel used
Gas: 1830
o
C or 3325
o
F
Fuel oil: 1956
o
C or 3553
o
F
Coal: 1927
o
C or 3500
o
F

2. Total combustion air temperature
Secondary air temperature
Primary air temperature
Air in-leakage temperature

3. Oxygen level at kiln outlet

4. Brick and coating temperature in the burning zone

Flame Target
Ignition as quick as possible
Highest flame temperature as possible
Page 84 of 98

Length as short as possible
As constant as possible
Primary air flow minimum to carry fuel in kiln
All above combined in such a way for not making erosion and direct contact of the flame on the
refractory

Shell temperature scanner is a good indication of flame profile.


Flame Adjustment

Increase in primary air
The speed will increase
Temperature will increase
The volume will become wider

Increase in primary air temperature
The plume will get shorter
The flame will become shorter
The flame will become wider

Increase in secondary air temperature
The flame temperature will increase
The flame length will decrease
The plume will decrease

Increase on the oxygen level
The flame length will increase
The flame temperature will decrease

The following factors serve to raise the flame temperature:
Page 85 of 98

Increasing the secondary air temperature
Using less primary air, thus making it possible to utilize more secondary air which is preheated
to higher temperature
Promoting rapid mixing of the air and fuel upon leaving the burner by improving the design of
primary air pipe and burner
Better atomization of the fuel oil by increasing the fuel oil temperature or employing a
mechanical device in the burner nozzle to bring a better atomization
By keeping hood pressure as close as possible from 0 in order to avoid air in-leaking in front of
kiln
Operating the kiln with neither a deficiency or excess of air by maintaining the oxygen content
of not less than 0.7% and not more than 3.0%


Rules on Flames
a) When the primary air pipe nozzle has accidentally been warped, resulting in an erratic flame
shape and direction, immediate steps should be taken to repair this condition
b) A flame should never be allowed to impinge upon the coating or bare refractory for a prolong
length of time
c) A flame should never be allowed to strike too hard upon the feed bed
d) Oil burners or gas burners should be centered well in the primary air pipe in order that an even
envelopment of air around the fuel jet takes place
e) Flame direction should be adjusted only when the kiln is in stable operating conditions and the
temperatures, fuel pressures, and air flow rates are at normal level. Flame direction changes can
be caused by unusual operating conditions. If any attempt were made to adjust the flame at
such a time, there will most likely be an undesirable flame once the kiln returns to normal
operating conditions again
f) It is better to make the desired adjustments in flame direction in several small steps instead of a
large one in order that the operating stability of the kiln is not affected adversely
g) Once the ideal flame direction has been obtained, the primary air pipe position should not be
changed unless a definite reason (such as to combat a ring formation or hot shell conditions)
makes it desirable
Page 86 of 98

h) To protect the primary air pipe from possible damage during a shutdown, a certain amount of
primary air flow must be maintained until the temperature inside the kiln is low enough
(approximately 600
o
F or 315
o
C) that the pipe cannot be damaged. Upon power failure when
primary air fan stops, the primary air pipe must be immediately removed from the burner hood.



COMBUSTION

What is combustion?
Rapid combination of oxygen with fuel resulting into heat

Fuels contains,
Carbon
Hydrogen
Sulfur

Oxygen Comes from Combustion Air
Carbon + Oxygen = Carbon dioxide + heat
Hydrogen + Oxygen = Water vapor + heat
Sulfur + Oxygen = Sulfur dioxide + heat

Proper Proportioning of Fuel, Oxygen and Heat
Perfect combustion
Combustion air = Neutral (stoichiometric) combustion air

Deficiency of Air (Reducing Conditions)
Incomplete combustion
Heat released is low (4500 Btu vs. 14500 Btu per lb carbon)
Unsafe operation (explosion in precipitator or anywhere in the system)

Page 87 of 98

Excess of Air (Oxidizing Conditions)
Complete combustion
Flame temperature decreases with increasing air, lower fuel economy
Recommended back-end oxygen is 1.0 to 1.5%

Combustion Air + Fuel = Combustion Gases

Combustion Air = Primary Air + Secondary Air + Leakage

Combustion Gases:
Carbon monoxide (CO) with incomplete combustion
Carbon dioxide (CO
2
) with complete combustion
Water vapor (H
2
O)
Sulfur dioxide (SO
2
)
Nitrogen (N
2
) from air
Excess oxygen (O
2
)

Good Combustion Requirements:
Proper proportioning of fuel and air
Thorough mixing of fuel and air
Initial and sustained ignition of the mixture

Mixing of Fuel and Air
Good mixing is important for mixture to be uniform throughout
Every particle of fuel must be in contact with an air particle
Solids must be pulverized to increase surface area for mass transfer
Liquids must be atomized (breaking up into tiny particles) to speed up evaporation (resulting to
vapors burn as gases)
Process of starting combustion
Can start at low temperatures, but may not be sustained
Minimum ignition temperature required for sustained ignition
Page 88 of 98

(Ignition continues without any external source of heat)

At this point:
Heat from Reaction > Heat Lost to Surroundings
Fixed carbon:* 400 450
o
C or, 752 842
o
F
Volatile Matter: 500 600
o
C or, 932 1112
o
F
C & H (methane): 632
o
C or, 1170
o
F
Coke: +/- 800
o
C or, 1472
o
F
Fuel oil: 200 300
o
C or, 392 572
o
F
* can be considered ignition temperature of coal

Theoretical Flame Temperature:
T
f
= LHV / (NCA + 1) S
Where T
f
= Maximum (theoretical) flame (in
o
C or
o
F)
LHV = Fuel low heating value (in kg/kg
f
or Btu/lb
f
)
NCA = Neutral combustion air (in kg/kg
f
or Btu/lb
f
)
S = Specific heat of combustion gases (=/- 0.29)

Typical Fuel Data:
Fuel
LHV
Kg/kg
f
(Btu/lb
f
)
NCA
Theo. Max. Flame T
o
C (
o
F)
Coal 6500 (11,700) 9.1 2460 (4460)
Oil 9870 (17,770) 13.7 2480 (4500)
Gas 11,500 (20,700) 16.6 2400 (4350)



Influences and Impact on Flame Temperature

Impact of Oxygen content of Kiln Gases on Flame Temperature (Figure #3)
Oxygen 1% 5%
Flame T
o
2465
o
C 1965
o
C
Page 89 of 98


Impact of Secondary Air Temperature on Flame Temperature
Sec. air T
o
420
o
C (770
o
F) 845
o
C (1553
o
F) 1093
o
C (2000
o
F)
Flame T
o
2180
o
C (39560
o
F) 2445
o
C (4433
o
F) 2610
o
C (4730
o
F)



HEAT TRANSFER IN A ROTARY KILN

Radiation (Flame Zone)
Flame/Gas by Material
Flame/Gas by Kiln shell
Very important because heat transfer x (Tf
4
Tm
4
)
Conduction
Wall to Material
Chain/crosses to Material

Convection
Gas to Material
Gas to Wall



BURNER PIPES AND NOZZLES

What is required from a burner?
A stable flame with proper geometry
Versatility
Safety

Parameters Affecting the Flame
Page 90 of 98

Fuel characteristics
Primary air and secondary air
The burner design

Key Parameters of Burner Design
Number of circuits
Primary air Quantity
Ejection velocities
Minimum velocity
Back pressure
Specific impulse
Diameter

Number of Air Circuits (Figure 1 to 6)

Single Circuit
Control is minimal
High velocity requires high fan pressure
Results in more wear

Two Circuits
Swirl + high velocity transport air
Additional control due to swirl
High fan pressure, high wear rate

Three Circuits
Swirl + high velocity axial
Low velocity transport air
More versatile

Primary Air Quantity
Page 91 of 98

Natural gas: 0 to 7% of total combustion air
Liquids: 7 to 10% of total combustion air
Solid fuels: Firing system dependent
Direct firing system: 30 to 35% of total combustion air
Semi-direct firing: Mill exit air is 18 to 25% (moisture dependent)
Air to burner can be controlled by diverting
Overflow to kiln hood
Indirect firing: 7 to 12% of total combustion air
Theoretically, indirect firing is the ideal solution.

Ejection Velocities
Gaseous and liquid fuels (with atomizing fluid)
Sonic range: 330 m/s (1083 ft/s)
Solid fuels
Single circuit: 5080 m/s (164263 ft/s)
Multiple circuits: 80170 m/s (262558 ft/s) for axial
5090 m/s (164295 ft/s) for swirl
2050 m/s (65164 ft/s) for transport

Minimum Velocities
Required to prevent solid fuel accumulation, 20 m/s (66 ft/s) in transport line and in axial $ swirl
annulus if these streams carry any fuel dust
Knowing the minimum flow rates, the pipe sizes can be determined.

Back Pressure
Typical values for a three-circuit burner;
700 1000 mmH
2
O for axial air
150 600 mmH
2
O for swirl air
600 1000 mmH
2
O for transport air
(up to 1200 mmH
2
O for modified three-circuit burner)

Page 92 of 98

Specific Impulse
Typically, 4 to 8 N/Gcal/h

Definition
Sp. impulse = Impulse (Newton)
Heat input (Gcal/h)

For Solid Fuel;
Impulse = air stream mass flow rate (kg/s) x tip velocity (m/s)
For Gaseous and Liquid (pneumatically atomized) Fuels;
Impulse = (abP c) S
Where: P = pressure (bars)
S = cross-section area (mm2)
a,b,c are atomizing fluid dependent
* 5 figures of burners to be attached at the above information.



FUELS IN THE CEMENT INDUSTRY

Solid Fuels:
Coal
Coal tailings
Petroleum coke (fluid, delayed)
Wood
Tires
Municipal waste, etc.

Liquid Fuels:
Oil (bunker C)
Liquid waste
Page 93 of 98

Coal slurry, etc.

Gaseous Fuels:
Natural gas (95% methane)
Landfill gases, etc.

Heating Value
Quantity of heat generated from 1 unit (kg, lb, ton, m
3
, liter) of fuel
Measured in kcal/kg, Btu/lb, MJ/ton, MJ/m
3
, kcal/liter
Can be approximated from the fuel composition

High Heating Value (HHV) vs. Low Heating Value (LHV)
High (or gross) Heating Value
Heat produced at constant volume by complete combustion of fuel, combustion
product condensed to liquid state, measured in the laboratory in an oxygen
bomb calorimeter.

Low (or net) Heating Value
Calculated from HHV by subtracting the latent heat of vaporization

The difference between HHV and LLV depends upon the hydrogen content of the fuel.
LHV = HHV - 92.7 x % H
2
(Btu/lb)

Examples of HHV and LHV for Various Fuels
Fuel % H
HHV
Btu/lb
LHV
Btu/lb (% of HHV)
Coal 5 12,000 11,540 (96%)
Coke 4 14,000 13,630 (97%)
Waste fuel 10 9,000 8,070 (90%)
Fuel oil 10 19,000 18,070 (95%)
Natural gas 25 23,300 20,680 (90%)
Page 94 of 98

SOLID FUELS

Coal, oil, gas and in recent years, petroleum coke are the main fuels used in cement kilns.

Coals are judged on what is called an proximate analysis which tells the percentage moisture, volatile
matter, fixed carbon, ash, sulfur, and heat value.

Coal is very complicated in structure, containing carbon, hydrogen, oxygen, nitrogen and sulfur in
various stages of combinations.

With the application of heat, these substances from various combustible gases are classed as volatile
matter. It is the first constituent of the coal to be liberated on heating.

The carbon that remains after the volatile matter is driven off is called fixed carbon.

Combustion is the chemical combination of oxygen with certain elements of the fuel to form compounds
with the release of heat. See figure below.

Every combustible substance has what is called an ignition temperature.

This is the temperature to which it must be raised before chemical combinations with oxygen or
combustion will take place.

These combinations liberate definite amounts of heat depending on the elements entering into the
combinations.

The principal combustible elements in coal are carbon and hydrogen. Any sulfur present is also
combustible, but is of minor importance from a heat standpoint.

The chief non-combustible elements in coal are silica, alumina and iron which form the ash.

Page 95 of 98


Bomb Calorimeter
The heat value of coal can be determined by using the bomb calorimeter. A precise amount of dry coal is
fired in an oxygen atmosphere in a sealed container which is immersed in a water bath. The change in
temperature of the water is measured and knowing the specific heat of water (1.0 Btu/lb
m
*
o
F) the heat
content of the coal is determined.

Volatile Matter (VM)
Portion of solid fuel liberated as gases and vapors, when it is heated in the absence of air. (result from
thermal decomposition)
For good coal: VM = 30 35%
For fluid coke: VM = 5 6%
Combustion start to be difficult when VM < 15%

Fixed Carbon (FC)
Residue left after volatile matter is driven off.
FC = 100 - (VM + Ash + Moisture)
For bituminous coal: FC = 40 60%
Coke: FC = 75 85%

Ash
Residue remaining after the fuel has been burnt.
Composed of compounds of silicon, aluminum, iron and calcium
Also some traces of Mg, Na, K and Ti.

Proximate Analysis
Determination of VM, FC, ash and moisture
Used for quick, preliminary appraisal of solid fuel

Ultimate Analysis
Quantitative determination of moisture, C, H, S, O and N
Page 96 of 98



DRYING, GRINDING AND FIRING SOLID FUELS

Ball Mill or Roller Mills are used.
Air from cooler / air heater / pre-heater exit is used for drying.

The drying systems can be; (Figure # 1, 2, 3)
Direct
Semi-direct
Indirect

Comparison of fuel drying system
Direct Semi-direct Indirect
Simple operation Most difficult to operate Simple operation
Relatively safe Safer than indirect Safety is most important
Primary air is high (30-35%)
All moisture to kiln
Primary air is low but all
moisture to kiln
Primary air can be as low as
desired (operation
independent)
Result in high heat
consumption
Heat penalty is lower than
direct
Good heat consumption
Lowest capital cost
Capital cost is in between
direct and indirect
Highest capital cost



Liquid Fuels
Essentially composed of C, H, and S
Evaporation at 200-300oC or 572oF
Atomization promotes evaporation
Classified according to:
Viscosity (measure of internal friction)
Specific gravity
Page 97 of 98

Heating value

Gaseous Fuels
Natural gas most commonly used (95% methane)
No preparation required for firing
Minimum ignition temperature (+/- 650oC or 1200oF)
Very little primary air is required
Injected at high pressure (i.e. high tip velocity) to promote turbulence

Comparison of the Three Major Fuels
Coal Oil Natural Gas
Installation is expensive Installation is simple Installation is simple
Can be stored in large storage
capacity
Storage capacity depends on
refinery
No storage
Radiant flame Radiant flame Non-radiant flame
Ash can be used as a raw
material
n/a n/a
Cheap Expensive Expensive
Noisy and dirty Depend on refinery Clean
Risk of explosion and fire n/a Flame control reacts
Quality can vary (% H
2
O &
Ash)
Quality is constant Quality is constant


COMBUSTION REACTIONS
Combustibles Reactions Heat Released
Carbon
C + O
2
= CO
2

C + O
2
= CO
14650 Btu/lb
4340 Btu/lb
Hydrogen 2H + O
2
= H
2
O 62100 Btu/lb
Sulfur S + O
2
= SO
2
4032 Btu/lb


Page 98 of 98

Non-Combustibles (Ash)
It must be treated as a raw material in raw mix
Silica (SiO
2
)
Alumina (Al
2
O
3
)
Iron (Fe
2
O
3
)



BASIC PRINCIPLES

SYSTEM OF UNITS
The fundamental quantities to be measured are;
Length
Mass
Time
Temperature
All other quantities that need to be measured can be expressed in terms of above quantities.

You might also like