Professional Documents
Culture Documents
INSPECTION
TESTING
CERTIFICATION
Agrment Certificate
92/2796
Product Sheet 1
website: www.geberit.co.uk
CERTIFICATION INCLUDES:
factors relating to compliance with Building
Regulations where applicable
factors relating to additional non-regulatory
information where applicable
independently verified technical specification
assessment criteria and technical investigations
design considerations
installation guidance
regular surveillance of production
formal three-yearly review.
KEY FACTORS ASSESSED
Strength the products have adequate strength to resist loads associated with installation and service
(see section 6).
Performance of joints products are easily installed and joints will remain watertight under all normal service
conditions (see section 7).
Durability the products will have a service life equivalent to PVC-U pipework systems (see section 13).
The BBA has awarded this Certificate to the company named above for the products described herein. These
products have been assessed by the BBA as being fit for their intended use provided they are installed, used
and maintained as set out in this Certificate.
On behalf of the British Board of Agrment
Date of First issue: 1 August 2013
Brian Chamberlain
Claire Curtis-Thomas
Chief Executive
The BBA is a UKAS accredited certification body Number 113. The schedule of the current scope of accreditation for product certification is
available in pdf format via the UKAS link on the BBA website at www.bbacerts.co.uk
Readers are advised to check the validity and latest issue number of this Agrment Certificate by either referring to the BBA website or contacting the BBA direct.
2013
Page 1 of 26
Regulations
In the opinion of the BBA, Geberit HDPE Above Ground Drainage System Pipes, Adaptors and Fittings, if installed,
used and maintained in accordance with this Certificate, will meet or contribute to meeting the relevant requirements
of the following Building Regulations (the presence of a UK map indicates that the subject is related to the Building
Regulations in the region or regions of the UK depicted):
The Building Regulations 2010 (England and Wales) (as amended)
Requirement: H1
Comment:
The products will convey the flow of foul water and minimise the risk of blockage or leakage. See sections
4.1, 7.1, 8 and 10 of this Certificate.
Requirement: H3(1)
Rainwater drainage
Comment:
The products will convey the flow of surface water and minimise the risk of blockage or leakage. See
section 4.1, 7.1, 8, 9 and 10 of this Certificate.
Regulation
Comment:
8(1)
Comment:
Regulation:
Standard:
9
3.6(a)
The products can contribute to a construction meeting this Regulation. See section 13 of this Certificate.
The products will satisfy the relevant requirements of this Standard, with reference to clause 3.6.1(1)(2). See
sections 4.1 and 9 of this Certificate.
Comment:
Standard:
3.7(b)(c)
Standard:
3.10
Precipitation
The system satisfies the relevant requirements of this Standard, with reference to clauses 3.10.1(1)(2) and
3.10.6(1)(2). See sections 7.1 and 7.2 of this Certificate.
Comment:
Standard:
Wastewater drainage
The products will satisfy the relevant requirements of this Standard, with reference to clause 3.7.1(1)(2). See
section 9 and 10 of this Certificate.
Comment:
7.1(a)(b)
Statement of sustainability
The product can contribute to meeting the relevant requirements of Regulation 9, Standards 1 to 6
and therefore will contribute to a construction meeting a bronze level of sustainability as defined in this
Standard.
Comment:
23
Comment:
Regulation:
28
Comment:
Regulation:
80
Sanitary pipework
Comment:
Regulation:
82
Rainwater drainage
Comment:
Additional Information
NHBC Standards 2013
NHBC accepts the use of Geberit HDPE Above Ground Drainage System Pipes, Adaptors and Fittings, provided it
is installed, used and maintained in accordance with this Certificate, in relation to NHBC Standards, Part 8 Services
and internal finishing Chapter 8.1 Internal services
Page 2 of 26
Technical Specification
1 Description
1.1 Geberit HDPE Above Ground Drainage System Pipes, Adaptors and Fittings comprise high density polyethylene
(HDPE) and comply with the recommendations of BS 2782-11 : Method 1121 B : 1997 and ISO 161-1 : 1996.
1.2 The pipes are black in colour and are normally supplied in 5 m lengths, but can be produced in suitable lengths to
form prefabricated pipeline elements. The nominal (outside) diameters and wall thicknesses of pipes are given in Table 1.
1.3 The dimensions of pipe fittings are given in Tables 2 to 14. The fittings covered are:
Reducers
Couplings
Access covers
Bends
Sockets
Adaptors.
Table 1 Pipe
L (m)
Article no.
d
s
d
di
A
cm2
360.000.16.0
361.000.16.0
363.000.16.0
364.000.16.0
365.000.16.0
366.000.16.0
367.000.16.0
368.000.16.0
369.000.16.0
370.000.16.0
371.000.16.0
372.000.16.0
Nominal diameter
d (outside) (mm)
Nominal diameter di
(inside) (mm)
Minimum wall
thickness s (mm)
40
50
56
63
75
90
110
125
160
200
250
315
34
44
50
57
69
83
101.4
115.2
147.6
187.6
234.4
295.4
3.0
3.0
3.0
3.0
3.0
3.5
4.3
4.9
6.2
6.2
7.8
9.8
Table 2 Reducers
Concentric reducer
Article no
d
(mm)
d1
(mm)
H
(mm)
h
(mm)
K
(mm)
360.557.16.1
361.559.16.1
363.559.16.1
363.560.16.1
364.559.16.1
364.560.16.1
364.565.16.1
365.559.16.1
365.560.16.1
365.565.16.1
365.570.16.1
366.559.16.1
366.560.16.1
366.565.16.1
366.570.16.1
366.575.16.1
367.559.16.1
367.560.16.1
367.565.16.1
367.570.16.1
367.575.16.1
367.580.16.1
368.570.16.1
368.575.16.1
368.580.16.1
368.585.16.1
369.535.16.1
40
50
56
56
63
63
63
75
75
75
75
90
90
90
90
90
110
110
110
110
110
110
125
125
125
125
160
32
40
40
50
40
50
56
40
50
56
63
40
50
56
63
75
40
50
56
63
75
90
63
75
90
110
110
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
40
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
60
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
Page 3 of 26
d
(mm)
50
56
56
63
63
63
75
75
75
75
90
90
90
90
110
110
110
110
110
110
125
125
125
125
125
125
160
160
160
d1
(mm)
40
40
50
40
50
56
40
50
56
63
50
56
63
75
40
50
56
63
75
90
50
56
63
75
90
110
110
125
140
A
(mm)
0.50
0.80
0.30
1.15
0.65
0.35
1.75
1.25
0.95
0.60
2.00
1.70
1.30
0.75
3.40
2.90
2.60
2.20
1.60
0.90
3.60
3.30
2.90
2.30
1.60
0.70
2.30
1.60
1.00
H
(mm)
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
h
(mm)
370
370
370
370
370
370
370
370
370
370
370
370
370
370
370
370
370
370
370
370
370
370
370
370
370
370
350
350
350
h1
(mm)
350
350
350
350
350
350
350
350
350
350
350
350
350
350
350
350
350
350
350
350
350
350
350
350
350
350
370
370
370
K
(mm)
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
d
(mm)
d1
(mm)
A
(mm)
L
(mm)
l1
(mm)
l2
(mm)
K1
(mm)
K2
(mm)
368.584.16.1
369.584.16.1
369.587.16.1
370.584.16.5
370.587.16.5
370.594.16.5
371.596.16.1
372.596.16.1
372.598.16.1
125
160
160
200
200
200
250
315
315
110
110
125
110
125
160
200
200
250
0.7
2.5
1.7
4.3
3.6
2
2.5
5.7
3.2
160
280
240
280
280
280
405
580
435
70
94
94
115
115
119
158
161
161
64
64
80
37
37
91
157
157
157
40
60
60
40
40
40
80
80
80
30
30
50
0
0
60
80
80
80
Table 3 Bends
Bend 90 long radius
X2
r
X1
K1
Article no.
d
(mm)
angle
()
X1
(mm)
X2
(mm)
K1
(mm)
r
(mm)
360.055.16.1
361.055.16.1
363.055.16.1
364.055.16.1
365.055.16.1
366.055.16.1
367.055.16.1
368.055.16.1
369.055.16.1
40
50
56
63
75
90
110
125
160
90
90
90
90
90
90
90
90
90
150
180
210
210
210
240
270
200
200
30
40
40
50
70
90
100
110
145
120
140
170
160
140
150
170
90
60
30
40
40
50
70
90
100
110
140
Page 4 of 26
X
d
K
Article no.
d
(mm)
angle
()
X
(mm)
K
(mm)
360.045.16.1
361.045.16.1
363.045.16.1
364.045.16.1
365.045.16.1
366.045.16.1
367.045.16.1
368.045.16.1
369.045.16.1
40
50
56
63
75
90
110
125
160
45
45
45
45
45
45
45
45
45
40
45
45
50
50
55
60
65
69
20
20
20
20
20
20
25
25
20
Article no.
d
(mm)
angle
()
X
(mm)
K
(mm)
r
(mm)
370.055.16.1
200
90
300
25
200
371.055.16.1
250
90
335
30
290
372.055.16.1
315
90
370
30
325
K
r
d
d
(mm)
angle
()
X
(mm)
K
(mm)
361.088.16.1
363.088.16.1
364.088.16.1
365.088.16.1
366.088.16.1
367.088.16.1
368.088.16.1
369.088.16.1
50
56
63
75
90
110
125
160
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
60
65
70
75
80
95
100
120
20
20
20
20
20
25
25
25
X
K
X
d
X2
X1
K2
Article no.
d
(mm)
angle
()
X1
(mm)
X2
(mm)
K1
(mm)
K2
(mm)
365.046.16.1
367.046.16.1
75
110
45
45
91
147
50
60
60
110
20
25
K1
d
Page 5 of 26
d
(mm)
angle
()
X1
(mm)
X2
(mm)
K1
(mm)
K2
(mm)
367.030.16.1
369.030.16.1
110
160
30
30
195
95
85
95
155
45
45
45
K2
X2
X1
K1
K2
Article no.
d
(mm)
angle
()
X1
(mm)
X2
(mm)
K1
(mm)
K2
(mm)
367.015.16.1
369.015.16.1
110
160
15
15
180
75
70
75
155
45
45
45
X2
X1 K1
Article no.
d
(mm)
angle
()
X
(mm)
K
(mm)
r
(mm)
370.030.16.1
200
30
150
20
200
371.030.16.1
250
30
160
30
420
372.030.16.1
315
30
170
30
473
Segment Bend
Article no.
d
(mm)
angle
()
X
(mm)
K
(mm)
370.015.16.1
200
15
155
40
371.015.16.1
250
15
103
372.015.16.1
315
15
103
Page 6 of 26
Bend 90 reduced
Article no.
d
(mm)
d1
(mm)
angle
()
X
(mm)
r
(mm)
361.872.16.1
50
40
90
40
40
363.873.16.1
56
50
90
40
40
364.873.16.1
63
50
90
50
50
364.874.16.1
63
56
90
50
50
X
1
d
X
r
d
Table 4 Sovent
Solvent
Article no.
d
d1 d2
(mm) (mm) (mm)
DN
(mm)
a
(mm)
B
(mm)
b
(mm)
H
(mm)
h
(mm)
h1
(mm)
h2
(mm)
L
(mm)
l
(mm)
l1
(mm)
l2
(mm)
100 /30
100/70
130
180
70
660
200
170
290
290
105
55
85
150 /133
100/70
133
230
95
710
190
170
350
343
130
80
110
I1
I2
d1
h2
d2
I2
d1/d2
b
B
d1
h1
d2
d1/d2
b
d1/d2
K3
d
d1 angle X1
X2
X3
H
h
K1
K3
(mm) (mm) () (mm) (mm) (mm) (mm) (mm) (mm) (mm)
d1
K1
X1
d
Page 7 of 26
90
225 138
35
35
360.159.16.1
K2 361.159.16.1
361.162.16.1
363.162.16.1
363.165.16.1
d1
364.159.16.1
364.162.16.1
364.165.16.1
364.170.16.1
365.159.16.1
365.162.16.1
365.165.16.1
365.170.16.1
365.175.16.1
366.159.16.1
366.162.16.1
366.165.16.1
366.170.16.1
366.175.16.1
366.180.16.1
367.159.16.1
367.162.16.1
367.165.16.1
367.170.16.1
367.175.16.1
367.180.16.1
367.185.16.1
368.162.16.1
368.165.16.1
368.170.16.1
368.175.16.1
368.180.16.1
368.185.16.1
368.189.16.1
369.175.16.1
369.185.16.1
369.189.16.1
369.195.16.1
370.180.16.1
370.185.16.1
370.189.16.1
370.195.16.1
370.196.16.1
371.185.16.1
371.189.16.1
371.195.16.1
371.196.16.1
371.197.16.1
372.185.16.1
372.189.16.1
372.195.16.1
372.196.16.1
372.197.16.1
372.198.16.1
Page 8 of 26
d
d1 angle X1
X2
X3
H
K1 K2
(mm) (mm) () (mm) (mm) (mm) (mm) (mm) (mm)
K3
(mm)
40
50
50
56
56
63
63
63
63
75
75
75
75
75
90
90
90
90
90
90
110
110
110
110
110
110
110
125
125
125
125
125
125
125
160
160
160
160
200
200
200
200
200
250
250
250
250
250
315
315
315
315
315
315
25
30
25
35
30
30
35
30
30
40
35
30
25
25
45
45
40
35
30
25
60
50
45
40
35
30
20
60
55
50
45
40
30
20
80
60
50
30
70
70
65
45
25
110
105
85
65
40
170
165
145
120
95
70
40
40
50
50
56
40
50
56
63
40
50
56
63
75
40
50
56
63
75
90
40
50
56
63
75
90
110
50
56
63
75
90
110
125
75
110
125
160
90
110
125
160
200
110
125
160
200
250
110
125
160
200
250
315
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
75
90
90
105
105
105
105
105
105
105
105
105
105
105
120
120
120
120
120
120
135
135
135
135
135
135
135
150
150
150
150
150
150
150
210
210
210
210
180
180
180
180
200
220
220
220
240
240
280
280
280
280
280
280
55
60
60
70
70
70
70
70
70
70
70
70
70
70
80
80
80
80
80
80
90
90
90
90
90
90
90
100
100
100
100
100
100
100
140
140
140
140
180
180
180
180
200
220
220
220
240
240
280
280
280
280
280
280
55
60
60
70
70
70
70
70
70
70
70
70
70
70
80
80
80
80
80
80
90
90
90
90
90
90
90
100
100
100
100
100
100
100
140
140
140
140
180
180
180
180
200
220
220
220
240
240
280
280
280
280
280
280
130
150
150
175
175
175
175
175
175
175
175
175
175
175
200
200
200
200
200
200
225
225
225
225
225
225
225
250
250
250
250
250
250
250
350
350
350
350
360
360
360
360
400
440
440
440
480
480
560
560
560
560
560
560
45 25
60 25
55 25
70 30
65 30
70 30
70 30
65 30
60 30
75 25
70 25
65 25
60 25
55 25
85 25
85 25
80 25
75 25
70 25
65 25
10 25
95 25
90 25
90 25
85 25
75 25
65 20
110 25
105 25
105 25
100 25
90 25
80 20
70 20
150 45
135 45
125 45
105 35
70 60
70 60
65 60
45 50
25 30
110 75
105 75
85 65
65 40
40 40
170 100
165 100
145 90
120 65
95 65
70 65
d1
K3
X3
K2
H
X1
K1
X2
d
Article no.
d
d1 angle X1
X2
X3
H
K1 K2 K3
(mm) (mm) () (mm) (mm) (mm) (mm) (mm) (mm) (mm)
360.109.16.1
361.109.16.1
361.112.16.1
363.112.16.1
363.115.16.1
364.109.16.1
364.112.16.1
364.115.16.1
364.120.16.1
365.109.16.1
365.112.16.1
365.115.16.1
365.120.16.1
365.125.16.1
366.109.16.1
366.112.16.1
366.115.16.1
366.120.16.1
366.125.16.1
366.130.16.1
367.109.16.1
367.112.16.1
367.115.16.1
367.120.16.1
367.125.16.1
367.130.16.1
367.135.16.1
368.120.16.1
368.125.16.1
368.130.16.1
368.135.16.1
368.139.16.1
369.125.16.1
369.130.16.1
369.135.16.1
369.139.16.1
369.145.16.1
370.125.16.1
370.135.16.1
370.139.16.1
370.145.16.1
370.146.16.1
371.135.16.1
371.139.16.1
371.145.16.1
371.146.16.1
371.147.16.1
372.135.16.1
372.139.16.1
372.145.16.1
372.146.16.1
372.147.16.1
372.148.16.1
40
50
50
56
56
63
63
63
63
75
75
75
75
75
90
90
90
90
90
90
110
110
110
110
110
110
110
125
125
125
125
125
160
160
160
160
160
200
200
200
200
200
250
250
250
250
250
315
315
315
315
315
315
Page 9 of 26
40
40
50
50
56
40
50
56
63
40
50
56
63
75
40
50
56
63
75
90
40
50
56
63
75
90
110
63
75
90
110
125
75
90
110
125
160
75
110
125
160
200
110
125
160
200
250
110
125
160
200
250
315
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
55
55
60
60
65
65
65
65
70
70
70
70
70
80
80
80
80
80
80
90
90
90
90
90
90
90
100
100
100
100
100
125
125
125
125
125
180
180
180
180
180
220
220
220
220
220
280
280
280
280
280
280
90
110
110
120
120
130
130
130
130
140
140
140
140
140
160
160
160
160
160
160
180
180
180
180
180
180
180
200
200
200
200
200
250
250
250
250
250
360
360
360
360
360
440
440
440
440
440
560
560
560
560
560
560
90
110
110
120
120
130
130
130
130
140
140
140
140
140
160
160
160
160
160
160
180
180
180
180
180
180
180
200
200
200
200
200
250
250
250
250
250
360
360
360
360
360
440
440
440
440
440
560
560
560
560
560
560
135
165
165
180
180
195
195
195
195
210
210
210
210
210
240
240
240
240
240
240
270
270
270
270
270
270
270
300
300
300
300
300
375
375
375
375
375
540
540
540
540
540
660
660
660
660
660
840
840
840
840
840
840
25
40
35
40
40
45
50
45
40
65
60
55
45
40
75
80
75
70
65
50
95
95
90
85
75
65
55
105
95
85
70
60
135
125
110
100
75
180
150
140
115
85
215
205
180
150
115
305
290
270
240
205
160
30
45
20
30
25
45
30
25
20
50
30
25
25
25
55
40
35
30
30
20
60
50
40
35
30
25
20
45
40
30
25
20
65
55
45
40
250
140
140
130
85
10
185
175
130
50
55
260
250
205
125
130
95
30
45
20
30
25
40
30
25
20
60
40
35
35
25
65
50
45
40
35
20
75
55
45
40
35
30
20
60
50
35
25
20
75
65
55
50
25
120
65
55
35
10
150
140
50
90
55
235
220
200
175
140
95
d
d1 angle X1
X2
X3
H
K1 K2 K3
(mm) (mm) () (mm) (mm) (mm) (mm) (mm) (mm) (mm)
367.209.16.1
110
40
45
90
95
60
75
367.212.16.1
110
50
45
90
95
60
75
367.235.16.1
110 110
45
90
50
15
15
K3
d1
d1
X3
K2
H
X1
K1
X2
d
D
K3
885
d
d1
D angle X1 X2 X3
H
K1 K2 K3
(mm) (mm) (mm) () (mm) (mm) (mm) (mm) (mm) (mm) (mm)
364.270.16.1
63
45
15
365.275.16.1
75
35
15
366.280.16.1
90
40
20
15
15
15
15
15
15
15
15
15
15
40
15
40
15
15
20
X3
H
d1
K1
d1
X1
d
K2
X2
180
d1
d1
Page 10 of 26
d
d1
D angle X1 X2 X3
H
K1 K2 K3
(mm) (mm) (mm) () (mm) (mm) (mm) (mm) (mm) (mm) (mm)
364.320.16.1
365.325.16.1
366.330.16.1
367.315.16.1
367.320.16.1
367.325.16.1
367.330.16.1
367.335.16.1
368.335.16.1
369.335.16.1
63
75
90
110
110
110
110
110
125
160
63
75
90
56
63
75
90
110
110
110
100
120
140
170
170
170
170
170
180
230
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
80
80
90
100
100
100
100
100
100
125
100
100
110
120
120
120
120
120
125
160
80
80
90
100
100
100
100
100
100
125
160
160
180
200
200
200
200
200
200
250
15
15
20
15
15
15
15
15
15
20
45
35
40
15
15
15
15
40
40
15
15
15
20
15
15
15
15
15
15
20
D
90
K3
88
X3
d1
d1
d1
H
X1
d
K1
K2
d1
X2
d
d1
D angle X1 X2 X3
H
K1 K2 K3
(mm) (mm) (mm) () (mm) (mm) (mm) (mm) (mm) (mm) (mm)
364.370.16.1
365.375.16.1
366.380.16.1
367.365.16.1
367.370.16.1
367.375.16.1
367.380.16.1
367.385.16.1
368.385.16.1
369.385.16.1
63
75
90
110
110
110
110
110
125
160
63
75
90
56
63
75
90
110
110
110
100
120
140
170
170
170
170
170
180
230
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
88.5
D
K3
88
d1
X3
d1
d1
X1
d
K1
K2
X2
d1
135
Page 11 of 26
80
80
90
100
100
100
100
100
100
125
100
100
110
120
120
120
120
120
125
160
80
80
90
100
100
100
100
100
100
125
160
160
180
200
200
200
200
200
200
250
15
15
20
15
15
15
15
15
15
20
45
35
40
15
15
15
15
40
40
15
15
15
20
15
15
15
15
15
15
20
d
d1
D angle X1 X2 X3
H
K1 K2 K3
(mm) (mm) (mm) () (mm) (mm) (mm) (mm) (mm) (mm) (mm)
364.600.16.1
63
45
15
365.600.16.1
75
35
15
40
15
40
15
D
K3
d1
5
88
X3
d1
d1
H
X1
K1
K2
d1
X2
135
d
d1
D angle X1 X2 X3
H
K1 K2 K3
(mm) (mm) (mm) () (mm) (mm) (mm) (mm) (mm) (mm) (mm)
364.605.16.1 63 63 100
365.605.16.1 75 75 120
366.605.16.1 90 90 140
367.605.16.1 110 110 170
368.605.16.1 125 110 180
369.605.16.1 160 110 230
88.5
88.5
88.5
88.5
88.5
88.5
D
90
K3
885
X3
d1
d1
d1
d1
X1
d
K1
K2
X2
d1
Page 12 of 26
80
80
90
100
100
125
100
100
110
120
120
160
80
80
90
100
100
125
160
160
180
200
200
250
15
15
20
15
15
20
45
35
40
40
40
15
15
15
20
15
15
20
Article no.
364.610.16.1 63 63
365.610.16.1 75 75
367.610.16.1 110 110
368.610.16.1 125 110
D
K3
d1
90
100
120
170
180
88.5
88.5
88.5
88.5
80
80
100
100
100
100
120
125
80
80
100
100
160
160
200
200
15
15
15
15
45
35
40
40
15
15
15
15
90
88
d1
X3
d1
d1
d1
X1
d
K1
90
K2
90
d1
X2
d1
(mm) (mm)
367.445.16.1 110
56
angle
()
88.5
X1
135
D
90
K3
885
X3
d1
d1
d1
d1
X1
d
K1
K2
X2
d1
Page 13 of 26
X2
X3
K1
K3
90
225
75
30
d
(mm)
d1
(mm)
A
angle X1
(mm)
()
(mm)
364.451.16.1
63
63
90
90
365.451.16.1
75
75
95
90
X3
(mm)
H
(mm)
K1
(mm)
K3
(mm)
105
70
175
45
10
105
70
175
35
366.451.16.1
90
90
110
90
120
80
200
30
367.451.16.1
110
110
90
90
135
105
240
45
368.451.16.1
125
110
130
90
150
100
250
60
10
369.451.16.1
160
110
150
90
210
140
350
120
40
K3
90
X3
d1
H
X1
K1
d
A
360.771.16.1
361.771.16.1
363.771.16.1
364.771.16.1
365.771.16.1
366.771.16.1
367.771.16.1
368.771.16.1
369.771.16.1
E
H X
E
d
d
(mm)
40
50
56
63
75
90
110
125
160
D
(mm)
52
62
68
76
89
104
125
142
178
E
(mm)
28
28
28
28
28
28
28
28
28
X
(mm)
3
3
3
3
3
3
3
3
3
H
(mm)
60
60
60
60
60
60
60
60
60
E
H
E
d
Page 14 of 26
Article no.
d
(mm)
D
(mm)
E
(mm)
H
(mm)
370.775.16.1
200
22.4
75
150
371.775.16.1
250
27.5
75
150
372.775.16.1
315
34.3
75
150
Table 9 Sockets
Expansion socket with ring seal for horizontal
or vertical installations
Article no.
D
E
H
h
d
d
(mm)
D
(mm)
E
(mm)
H
(mm)
h
(mm)
K
(mm)
379.791.16.1
32
48
70 - 105
85
10
360.700.16.1
40
70
70 - 105
233
65
55
361.700.16.1
50
80
70 - 105
233
65
55
363.700.16.1
56
86
70 - 105
233
65
55
364.700.16.1
63
93
70 - 105
233
65
55
368.700.16.1
125
162
70 - 105
239
65
55
369.700.16.1
160
202
70 - 105
240
70
55
370.700.16.1
200
250
170-205
400
125
110
371.700.16.1
250
291
170-205
425
170
140
372.700.16.1
315
361
170-205
458
175
140
d
(mm)
D
(mm)
H
(mm)
h
(mm)
360.779.16.1
40
57
63
20
361.779.16.1
50
67
63
20
363.779.16.1
56
72
64
20
364.779.16.1
63
80
65
20
365.779.16.1
75
92
88
25
366.779.16.1
90
108
88
25
367.779.16.1
110
131
88
25
368.779.16.1
125
149
88
25
369.779.16.1
160
188
123
30
Article no.
d1
(mm)
d2
(mm)
90
110
H
h
d
Adaptor sleeve
75
367.928.16.1
d2
d1
Article no.
361.930.16.1
H
h
d
(mm)
D
(mm)
H
(mm)
h
(mm)
50
67
156
113
365.930.16.1
75
92
118
55
369.930.16.1
160
188
156
60
Page 15 of 26
Article no.
h1
d
h2
d
(mm)
Rg
(mm/in)
D
(mm)
H
(mm)
h
(mm)
h1
(mm)
h2
(mm)
379.740.16.1
32
44 x 1/8
56
45
26
30
10
360.740.16.1
40
52 x 1/6
64
63
33
50
20
361.740.16.1
50
62 x 1/6
74
63
33
50
20
363.740.16.1
56
70 x 1/6
85
68
35
50
20
364.740.16.1
63
75 x 1/6
90
68
42
50
20
365.740.16.1
75
95 x 1/6 112
96
45
75
25
366.740.16.1
90
97
50
75
25
367.740.16.1
110
97
65
75
25
Article no.
d
(mm)
Rg
(mm/in)
D
(mm)
H
(mm)
h
(mm)
h1
(mm)
h2
(mm)
56
70 x 1/6
85
98
35
80
50
363.931.16.1
H
h1
d
h2
Article no.
d
(mm)
D
(mm)
H
(mm)
360.802.92.1
40
42
35
365.802.92.1
75
78
35
369.802.92.1
160
164
30
Page 16 of 26
Table 12 Ends
Weld on caps
Article no.
d
(mm)
360.812.16.1
40
361.812.16.1
50
363.812.16.1
56
364.812.16.1
63
365.812.16.1
75
366.812.16.1
90
367.812.16.1
110
368.812.16.1
125
369.812.16.1
160
370.812.16.1
200
H
d
d
(mm)
H
(mm)
361.929.16.1
50
40
363.929.16.1
56
40
365.929.16.1
75
44
366.929.16.1
90
45
367.929.16.1
110
46
369.929.16.1
160
65
d
(mm)
Rg
(mm/in)
D
(mm)
H
(mm)
360.781.16.1
40
52 x 1/6
64
33
361.781.16.1
50
62 x 1/6
74
33
363.781.16.1
56
70 x 1/6
85
35
364.781.16.1
63
75 x 1/6
90
42
365.781.16.1
75
95 x 1/6
112
45
366.781.16.1
90
110 x 1/4
129
50
367.781.16.1
110
130 x 1/4
149
65
Rg
Table 13 Flanges
Sintered cast iron flange
d
k
D
Article no.
d
(mm)
D
(mm)
k
(mm)
m
(mm)
H
(mm)
n ST
361.745.00.1
50
150
110
18
12
363.745.00.1
56 / 63
165
125
18
12
365.745.00.1
75
185
145
18
12
366.745.00.1
90
200
160
18
14
367.745.00.1
110
220
180
18
14
368.745.00.1
125
250
210
18
14
369.745.00.1
160
285
240
23
14
370.745.00.1
200
340
295
23
14
371.745.00.1
250
395
350
23
16
12
372.745.00.1
315
445
400
23
20
12
Page 17 of 26
Flange adaptor
Article no.
h1
H h
d
D1
d
(mm)
D
(mm)
D1
(mm)
H
(mm)
h
(mm)
h1
(mm)
361.744.16.1
50
80
54
60
42
363.744.16.1
56
90
68
60
36
364.744.16.1
63
90
68
60
37
365.744.16.1
75
110
78
65
40
366.744.16.1
90
128
96
70
44
11
367.744.16.1
110
148
116
75
48
12
368.744.16.1
125
160
131
80
50
14
369.744.16.1
160
198
165
90
51
17
370.744.16.1
200
260
206
78
54
14
371.744.16.1
250
325
256
78
52
16
372.744.16.1
315
370
315
100
70
20
d
(mm)
D
(mm)
H
(mm)
h
(mm)
h1
(mm)
h2
(mm)
370.751.16.1
200
213
191
41
60
15
371.751.16.1
250
262
201
41
60
20
372.751.16.1
315
326
201
41
60
20
D1
h2
H
h1
h
h2
h1
h
H
h
d
d
(mm)
D
(mm)
H
(mm)
h
(mm)
360.772.16.1
40
47
68
32
361.772.16.1
50
57
68
32
363.772.16.1
56
65
58
27
364.772.16.1
63
70
72
34
365.772.16.1
75
90
72
34
366.772.16.1
90
103
92
44
367.772.16.1
110
120
117
56
Article no.
d
(mm)
D
(mm)
H
(mm)
364.989.16.1
63
100
70
367.989.16.1
110
170
110
369.989.16.1
160
230
160
Page 18 of 26
1.4 There are six methods available for joining the pipe/fittings (see Figure 1). These are:
butt welding utilising Geberit hot-plate type KSS160 or KSS200
electroweld sleeve couplings (see Table 8) a Geberit welding apparatus reference ESG160 must be used for
pipes 40 mm to 160 mm diameter and reference ESG315 for pipes 200 mm to 315 mm diameter
ring-seal socket (see Table 9) are for welding to pipe or fitting spigots
screw-threaded joints (see Table 10) consists of a male-threaded spigot which must be butt welded to the pipe or
fitting, an EPDM compression seal, a nylon bush and a polyethylene female-threaded cap
expansion socket (see Table 9) are for welding to pipe or fitting spigots at one end and incorporate a ring-seal
joint at the other. They permit longitudinal movement between adjacent pipes
a flanged joint (see Table 13) incorporates two flange adaptors which must be butt welded to the pipe/spigots to
be joined, an EPDM flange seal, two cast-iron flange plates and the appropriate number of steel bolts and washers.
Figure 1 Joint types
1.2
1.1
butt weld
1.4
1.3
electroweld
sleeve
coupling
(with or
without
butt ring)
socket joint
1.6
1.5
screwthreaded
joint
expansion
socket
flange joint
threaded
joint
HDPE
HDPE
PVC-U
cast
iron
to PVC-U
to cast
iron and
steel
2 Manufacture
2.1 The HDPE pipes are extruded from batch mixed raw materials and cut to length and the fittings are injection
moulded or welded extrusions.
2.2 As part of the assessment and ongoing surveillance of product quality, the BBA has:
agreed with the manufacturer the quality control procedures and product testing to be undertaken
assessed and agreed the quality control operated over batches of incoming materials
monitored the production process and verified that it is in accordance with the documented process
evaluated the process for management of nonconformities
checked that equipment has been properly tested and calibrated
undertaken to carry out the above measures on a regular basis through a surveillance process, to verify that the
specifications and quality control operated by the manufacturer are being maintained.
2.3 The management system of Geberit Ltd has been assessed and registered as meeting the requirements of
BS EN ISO 9001 : 2008 by SQS (Registration No. 20644).
Page 19 of 26
Design Considerations
4 General
4.1 Geberit HDPE Above Ground Drainage System Pipes, Adaptors and Fittings are satisfactory for use in
domestic, commercial and public buildings and in installations designed in accordance with DD ENV 13801 :
2001 and BS EN 12056-2 and -3 : 2000 for the conveyance of surface water and domestic sewage as is
permitted to be discharged into public sewers by the Water Industry Act 1991 (England and Wales), and
surface water and sewage as is permitted and defined by the Sewerage (Scotland) Act 1968 and the Water and
Sewerage Services (Northern Ireland) Order 1973.
4.2 This Certificate does not cover for use of any of the system for untreated trade effluent.
4.2 The average linear expansion coefficient for Geberit pipes is 2 x 10 4 mm 1C. Installations must be designed
to accommodate or prevent the anticipated thermal movement as given in sections 4.3 to 4.7.
4.3 Movement of pipes can be prevented by embedding in concrete or by rigid fixings.
4.4 The adhesion between concrete and pipe is inadequate to prevent movement. When installed within concrete
floors the movement is prevented by the use of electro weld sleeves or bushes which protrude from the external surface
of the pipe. These fittings must be used near each branch connection. Ring-seal sockets should not be embedded in
concrete. The expansion and contraction forces created by thermal movement must be accommodated by the concrete.
4.5 The forces exerted on pipe supports, anchors and the structure must be considered when this approach is used.
Rigid fixings are not considered suitable for pipes over 160 mm in diameter. Guidance on the load exerted on fixings
is available from the Certificate holder.
4.6 Vertical and horizontal expansion can be catered for by the linear expansion socket. The product is designed to
cope with the expansion equivalent to a 6 m run of pipe through a temperature change of 80C. This product should
be used in conjunction with rigid anchor fixings and sliding guide hangers as fully described in the Certificate holders
installation guide.
4.7 Thermal movement can also be accommodated by the incorporation of a deflection leg in the system design (see
Figure 2). The maximum anticipated movement is determined using graph 1, and the length of the required deflection
leg appropriate to the predicted movement is read from graph 2. The procedure is fully explained in the Certificate
holders Installation Guide.
Page 20 of 26
LA
DS
BS
G
BS
F
length variation
expansion leg
deflection leg
sliding clamp
fixed clamp (or point in the structure)
9m
m
10
90
80
70
60
50
40
30
20
10
0
8m
4 4.8 6
20
outer diameter
12
90
1 6
31
5
110
140
75
32
40
m
3
1m
100
temperature difference ( t in C)
2m
pipe length
506
3
LA =
DS =
BS =
G =
F =
LA
25
0
DS
20
0
18
16
14
12
10
8
determination of the
deflection leg of PE
6
4.8
4
9 10 11 12 13 14 15 16
Graph 1
5 Practicability of installation
The products are designed to be installed by plumbers experienced with this type of product.
6 Strength
6.1 Geberit HDPE pipes, adaptors and fittings will have adequate resistance to the forms of loading associated
with installation and normal service conditions.
6.2 The products should be protected from impacts, for example from being dropped from height.
7 Performance of joints
7.1 The joints will not be adversely affected by thermal movement provided the correct provision is made.
7.2 The joints will remain watertight under conditions of pipeline movement in excess of those expected to occur in
normal good drainage practice.
8 Flow characteristics
8.1 A system comprising Geberit HDPE pipes, adaptors and fittings will have satisfactory flow characteristics.
Primary ventilated stack systems to BS EN 12056-2 : 2000, sub-clause 4.3.1 and Table 1, are restricted in
accordance with sub-clause 6.5.1 and Table 11. For flow capacity calculations, ball fittings should be
considered as having square entries.
8.2 Use of Sovent branches in a stack allows the design capacity of a 110 mm primary ventilated stack to be
increased to 7.6 ls-1, avoiding the need for additional ventilation. The stack design must be in accordance with the
Certificate holders guidelines (see Figure 3). A Sovent fitting must be installed at each floor above the ground floor,
even if appliances are not connected. The ground pipe must be 160 mm in diameter and a pressure relief line must be
installed at the bend at the bottom of the stack.
8.3 Offsets in the wet portion of a discharge stack should be avoided. However, if unavoidable, large radius bends
should be used (see BS EN 12056-2 : 2000, National Annex 3.5.4). A ventilation stack may be necessary above
and below the offset (see Figure 4).
Page 21 of 26
8.4 When using ball fitting branches, it is possible to position branch entries directly opposite each other without risk
of crossflow.
Figure 3 Design of stack with Sovent branch
expansion joint
Sovent fitting
expansion joint
Sovent fitting
expansion joint
Sovent fitting
Page 22 of 26
(b)
for ventilated
systems
R
D
(a)
for ventilated
systems
9 Resistance to chemicals
The products will be unaffected by those types and quantities of chemicals likely to be found in the effluents defined in
section 4.1.
12 Maintenance
Sections of the system can be removed and replaced. The installation must be designed so that access is provided in
accordance with BS EN 12056-2 : 2000, National Annex NG4.
13 Durability
In the opinion of the BBA, when used in the context of this Certificate, the materials from which the component
parts of the pipes, adaptors and fittings are manufactured will not significantly deteriorate and the products will
have serviceable life equivalent to PVC-U sanitary pipework systems.
Page 23 of 26
Installation
15 Procedure
15.1 Installation of Geberit HDPE Above Ground Drainage System Pipes, Adaptors and Fittings must be in accordance
with the Certificate holders literature and with the guidance and recommendations for building drainage and sanitation
are given in BS EN 752 : 2008 and BS EN 12056-5 : 2000 where appropriate.
15.2 End-to-end butt weld joints must be carried out under controlled conditions:
pipe must be cut square and clean using a Geberit pipe cutter
the welding plate must be clean
the required lateral pressure must be applied
appropriate heat-up and weld time should be used.
Temperature ( C)
10
+10
+20
70
80
90
105
170
180
190
205
15.6 Pipes are secured by anchor brackets on hangers (not covered by this Certificate). The maximum spacing of the
supports must be 1.2 m on vertical pipes and 0.5 m on near horizontal pipes.
Technical Investigations
16 Tests
16.1 The results of tests carried out by the Centre Scientifique et Technique du Btiment (CSTB) on Geberit HDPE
pipes, adaptors and fittings were assessed in relation to comparable UK test requirements. Tests were carried out to
include:
dimensional control
Vicat softening point
bending temperature under load
specific mass
heat revision
tensile strength
thermal shock
resistance to pressure
deflection of typical assemblies.
Page 24 of 26
17 Investigations
The technical data in the confirmation report of the Commission Charge de Formuler des Avis Techniques were
evaluated in the context of UK above ground drainage practice.
Bibliography
BS 2782-11 : Method 1121 B : 1997 ISO 161-1 : 1996 Methods of testing plastics. Thermoplastics pipes, fittings
and valves. Thermoplastics pipes for the conveyance of fluids. Nominal outside diameters and nominal pressures.
Metric series
BS EN 752 : 2008 Drain and sewer systems outside buildings
BS EN 1055 : 1996 Plastics piping systems Thermoplastics piping systems for soil and waste discharge inside
buildings Test method for resistance to elevated temperature cycling
BS EN 1519-1 : 2000 Plastics piping systems for soil and waste discharge (low and high temperature) within the
building structure Polyethylene (PE) Specifications for pipes, fittings and the system
BS EN 12056-2 : 2000 Gravity Drainage Systems inside Buildings Sanitary pipework, layout and calculation
BS EN 12056-3 : 2000 Gravity Drainage Systems inside Buildings Roof drainage, layout and calculation
BS EN 12056-5 : 2000 Gravity Drainage Systems inside Buildings Installation and testing, instructions for
operation, maintenance and use
DD ENV 13801 : 2001 Practice for installation
Page 25 of 26
Conditions of Certification
18 Conditions
18.1 This Certificate:
relates only to the product/system that is named and described on the front page
is issued only to the company, firm, organisation or person named on the front page no other company, firm,
organisation or person may hold or claim that this Certificate has been issued to them
is valid only within the UK
has to be read, considered and used as a whole document it may be misleading and will be incomplete to be
selective
is copyright of the BBA
is subject to English Law.
18.2 Publications, documents, specifications, legislation, regulations, standards and the like referenced in this Certificate
are those that were current and/or deemed relevant by the BBA at the date of issue or reissue of this Certificate.
18.3 This Certificate will remain valid for an unlimited period provided that the product/system and its manufacture
and/or fabrication, including all related and relevant parts and processes thereof:
are maintained at or above the levels which have been assessed and found to be satisfactory by the BBA
continue to be checked as and when deemed appropriate by the BBA under arrangements that it will determine
are reviewed by the BBA as and when it considers appropriate.
18.4 The BBA has used due skill, care and diligence in preparing this Certificate, but no warranty is provided.
18.5 In issuing this Certificate, the BBA is not responsible and is excluded from any liability to any company, firm,
organisation or person, for any matters arising directly or indirectly from:
the presence or absence of any patent, intellectual property or similar rights subsisting in the product/system or any
other product/system
the right of the Certificate holder to manufacture, supply, install, maintain or market the product/system
actual installations of the product/system, including their nature, design, methods, performance, workmanship and
maintenance
any works and constructions in which the product/system is installed, including their nature, design, methods,
performance, workmanship and maintenance
any loss or damage, including personal injury, howsoever caused by the product/system, including its manufacture,
supply, installation, use, maintenance and removal
any claims by the manufacturer relating to CE marking.
18.6 Any information relating to the manufacture, supply, installation, use, maintenance and removal of this product/
system which is contained or referred to in this Certificate is the minimum required to be met when the product/system
is manufactured, supplied, installed, used, maintained and removed. It does not purport in any way to restate the
requirements of the Health and Safety at Work etc. Act 1974, or of any other statutory, common law or other duty
which may exist at the date of issue or reissue of this Certificate; nor is conformity with such information to be taken as
satisfying the requirements of the 1974 Act or of any statutory, common law or other duty of care.
2013
Page 26 of 26