Professional Documents
Culture Documents
5 BTS3012AE Cables
BTS3012AE Cables
5-1
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
The cables for the built-in battery are the GND cable, -48 V power cable, cable between the
wiring copper bar and the battery, cable between batteries, and signal cable for the temperature
sensor of the built-in battery.
5.8 Cable Between the BTS3012AE and the Auxiliary Equipment
The cables between the BTS3012AE and the auxiliary equipment are the signal cable for the
alarm box, power cable between the IBBS and the BTS3012AE, equipotential cable between
the IBBS and the BTS3012AE, and cables for the IBBS door control sensor and temperature
sensor.
5-2
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Issue 01 (2007-09-10)
Item
Sub-Item
Installation
Positions
Remarks
Power cable
External input
power cable (220 V
AC 3-phase 4-core
input)
External input
power cable (220 V
AC single-phase 2core input)
External input
power cable (110 V
AC dual-live input)
5-3
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Item
Sub-Item
Installation
Positions
Remarks
PGND cable
5-4
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Item
Sub-Item
Installation
Positions
Remarks
Equipotential
cable
Equipotential cable
Refer to 5.2.3
Equipotential Cable of
the BTS.
Issue 01 (2007-09-10)
Power cable
between the DC
power distribution
box and the DTRU
subrack
Power cable
between the DC
power distribution
box and the DAFU
subrack
Power cable
between the DC
power distribution
box and the common
subrack
Power cable
between the DC
power distribution
box and the fan
subrack
Refer to 5.3.3
BTS3012AE Power
Cable Between the DC
Power Distribution Box
and the Common
Subrack.
Refer to 5.3.4
BTS3012AE Power
Cable Between the DC
Power Distribution Box
and the Fan Subrack.
5-5
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Item
Transmission
cables
Sub-Item
Installation
Positions
Remarks
Power cable
between the DC
power distribution
box and the fan filter
unit
Refer to 5.3.5
BTS3012AE Power
Cable Between the DC
Power Distribution Box
and the Fan Filter Unit.
E1 cable
5-6
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
Item
5 BTS3012AE Cables
Sub-Item
Installation
Positions
Remarks
E1 signal transfer
cable
Power detection
cable
Diversity receive
short-circuiting
cable
Signal cable
between combined
cabinets
Issue 01 (2007-09-10)
5-7
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Item
Sub-Item
Installation
Positions
Remarks
Signal cable
between cabinet
groups
Signal cable
between the DSCB
and the DAFU
subrack
5-8
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
Item
5 BTS3012AE Cables
Sub-Item
Installation
Positions
Remarks
RS485 environment
monitoring signal
cable
Issue 01 (2007-09-10)
5-9
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Item
Sub-Item
Installation
Positions
Remarks
Monitoring transfer
cable between the
NPMI and the
DSCB
Refer to 5.5.14
Monitoring Transfer
Signal Cable Between
the NPMI and the DSCB
in the BTS3012AE .
Signal cable
between the DFCB
and the DFCU
5-10
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
Item
5 BTS3012AE Cables
Sub-Item
Installation
Positions
Remarks
RF cables
RF signal cable
1/4-inch RF jumper
Consists of the RF TX
signal cable and the
RF RX signal cable.
l
The RF TX signal
cable connects the
TX port on the
DTRU and the
corresponding TX
port on the DDPU.
The RF RX signal
cable connects the
RX port on the
DTRU and the
corresponding RX
port on the DDPU.
Refer to 5.6.2 RF
Jumpers for the
BTS3012AE.
Issue 01 (2007-09-10)
5-11
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Item
Sub-Item
Installation
Positions
1/2-inch RF jumper
Remarks
GND cable
48 V power cable
Cable between
storage batteries
5-12
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
Item
5 BTS3012AE Cables
Sub-Item
Installation
Positions
Remarks
If the BTS3012AE
is configured with
the 200 AH built-in
batteries, the OT
terminal connects
to the positive
terminal on the left
storage battery in
the front row
within the 50 AH
battery cabin.
If the BTS3012AE
is configured with
the 100 AH or 150
AH built-in
batteries, the OT
terminal connects
to the positive
terminal on the left
storage battery in
the front row at the
upper layer within
the 150 AH battery
cabin.
Cable between
the
BTS3012AE
and the
auxiliary
equipment
Issue 01 (2007-09-10)
5-13
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Item
Sub-Item
Installation
Positions
Remarks
Refer to 5.6.2 RF
Jumpers for the
BTS3012AE.
Refer to 5.8.3
Equipotential Cable
Between the IBBS and
the BTS3012AE .
5-14
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
NOTE
The combining short-circuiting signal cable is not required when the DTRU (type B) is used. The combining
short-circuiting signal cable is used only for the internal combining of the DTRU (type A).
Function
The AC power cable is used to transmit 220 V AC or 110 V AC power from the power interface
box to the external power connecting terminal of the power lightning arrestor in the cabinet. The
BTS3012AE supports three power input modes: 220 V AC 3-phase input, 220 V AC singlephase input, and 110 V AC dual-live input.
Appearance
NOTE
The AC power cables for the BTS3012AE are available at local markets. The colors of the cables
must comply with the local rules and regulations.
If the local rules and regulations have no special requirements pertaining to the color of the cable,
use the cables that are delivered with the BTS.
The L wire is red and the N wire is black by default. The OT terminals of AC power cables are made
on site.
The AC power cables are prepared on site. Table 5-2 lists the specifications for the AC power
cables.
Issue 01 (2007-09-10)
5-15
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Cable
Quantity
Sectional
Area
Color
220 V AC 3-phase
4-core input
10 mm2
Red
10 mm2
Black
16 mm2
Red
16 mm2
Black
110 V AC dual-live L
input
N
16 mm2
Red
16 mm2
Black
Pin Description
None
Installation Positions
The three types of AC power cables are routed into a BTS3012AE cabinet through the cable
hole for the external power cable at the bottom of the cabinet, and then connected to the wire
post on the AC power lightning arrestor. Table 5-3 describes the installation positions.
Table 5-3 Installation positions of the AC Power Cables
Power Input Mode
Power Cable
Installation Position
L1
L2
L3
L1
L2
110 V AC dual-live
input
5-16
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Power Cable
Installation Position
Function
The PGND cables keep the cabinet well grounded.
l
The PGND cables for the BTS3012AE cabinet ensures proper grounding of the whole
cabinet.
The PGND cables in the transmission interface box that are used to keep this box well
grounded.
The PGND cables in the power interface box are used to keep this box well grounded.
The PGND cable for the front door ensures the proper grounding of the front door.
The PGND cable for the back door ensures the proper grounding of the back door.
Appearance
The PGND cables for the BTS3012AE cabinet, front door, and back door are green and yellow
cables with a cross-sectional area of 25 mm2. If you decide to prepare the cable by yourself,
choose a green and yellow cable with a plastic insulation copper core and with a cross-sectional
area of at least 25 mm2.
The PGND cables for the transmission interface box and the power interface box are yellow and
green in color with a cross-sectional area of 16 mm2. If you prepare the cable, it should be a
green and yellow cable with a plastic insulation copper core and with a cross-sectional area of
at least 16mm2.
Pin Description
None
Installation Positions
Table 5-4 shows the installation positions of the PGND cables for the BTS3012AE.
Issue 01 (2007-09-10)
5-17
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Table 5-4 Installation positions of the PGND cables for the BTS3012AE
Cable Type
One End
Function
The equipotential cable helps keep an equal potential between the cabinets and ensuring the safe
operation of the BTSs.
Structure
The equipotential cable is a green and yellow cable with cross-sectional area of 25 mm2. Both
ends of the cable use OT terminals. See Figure 5-1 for details.
Figure 5-1 Structure of the equipotential cable
Pin Assignment
None.
5-18
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Installation Positions
Table 5-5 describes the installation positions of the equipotential cable.
Table 5-5 Installation positions of the equipotential cable
Cabinet Model
BTS3012
BTS3012AE
BTS3006C
BTS3002E
Connects to one
external PGND bar
Issue 01 (2007-09-10)
5-19
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
5.3.5 BTS3012AE Power Cable Between the DC Power Distribution Box and the Fan Filter
Unit
The power cable between the DC power distribution box and the fan filter unit leads the power
to the control board of the fan filter unit.
Functions
The power cables between the DC power distribution box and the DTRU subrack introduce
power from the DC power distribution box to the DTRU subrack. The power cables supply
power to the DTRUs in the DTRU subrack.
Appearance
The power cables between the DC power distribution box and the DTRU subrack are six
independent cables. Each DTRU is configured with one independent power cable. The six cables
have the save structure, as shown in Figure 5-2.
Figure 5-2 Power cable between the DC power distribution box and the DTRU subrack
View A 1
A1
A2
A3
2 View B
W1
W2
A1
A2
A3
X2
X1
(1) 3V3 power connector
Pin Assignment
Table 5-6 lists the pin assignment of the cables between the DC power distribution box and the
DTRU subrack.
Table 5-6 Pin assignment of the cables between the DC power distribution box and the DTRU
subrack
5-20
Wire
X1 End
X2 End
Wire Color
W1
X1.A1
X2.A1
Black
W2
X1.A3
X2.A3
Blue
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Installation Positions
The power cables between the DC power distribution box and the DTRU subrack are six
independent cables. Table 5-7 shows the installation positions of the power cables.
Table 5-7 Installation positions of the cable between the DC power distribution box and DTRU
subrack
Cable Name
Functions
The power cables between the DC power distribution box and the DAFU subrack introduce
power from the DC power distribution box to the DAFU subrack. The power cables supply
power to the DDPUs or DFCUs in the DAFU subrack.
Appearance
Two cables are connected between the DC power distribution box and the DAFU subrack. Each
cable has one connector at one end and three connectors at the other end. The one-connector end
connects to the DC power distribution box and the 3-connector end to the DAFU subrack and
Issue 01 (2007-09-10)
5-21
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
supplies power to the three DDPUs or DFCUs. The two cables have the same structure, as shown
in Figure 5-3.
Figure 5-3 Power cable between the DC power distribution box and the DAFU subrack
1
W1
2 View B
W2
X1
View A
A1
A2
A3
W3
W4
X2
W5
A1
A2
A3
X4
W6
X3
Pin Assignment
Table 5-8 lists the pin assignment of the cables between the DC power distribution box and the
DAFU subrack.
Table 5-8 Pin assignment of the cables between the DC power distribution box and the DAFU
subrack
Wire
One End
Other End
Wire Color
W1
X1.A1
X4.A1
Black
W3
X2.A1
Black
W5
X3.A1
Black
W2
X1.A3
W4
X2.A3
Blue
W6
X3.A3
Blue
X4.A3
Blue
Installation Positions
Table 5-9 lists the installation positions of the cables between the DC power distribution box
and the DAFU subrack.
5-22
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Table 5-9 Installation positions of the cables between the DC power distribution box and the
DAFU subrack
Cable Name
Functions
The power cable between the DC power distribution box and the common subrack introduces
power from the DC power distribution box to the common subrack. The power cable supplies
power to the common subrack.
Appearance
Only one power cable is connected between the DC power distribution box and the common
subrack. Figure 5-4 shows the structure of the power cable.
Figure 5-4 Power cable between the DC power distribution box and the common subrack
View A 1
A1
A2
A3
2 View B
W1
W2
X2
X1
(1) 3V3 power connector
Issue 01 (2007-09-10)
A1
A2
A3
5-23
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Pin Assignment
Table 5-10 lists the pin assignment of the cable between the DC power distribution box and the
common subrack.
Table 5-10 Pin assignment of the cable between the DC power distribution box and the common
subrack
Wire
X1 End
X2 End
W1
X1.A1
X2.A1
W2
X1.A3
X2.A3
Installation Positions
Table 5-11 lists the installation positions of the cable between the DC power distribution box
and the common subrack.
Table 5-11 Installation positions of the cable between the DC power distribution box and the
common subrack
Cable Name
Functions
The power cable between the DC power distribution box and the fan subrack introduces power
from the DC power distribution box to the fan subrack. The power cable supplies power to the
fan subrack.
Appearance
Figure 5-5 shows the structure of the power cable between the DC power distribution box and
the fan subrack.
5-24
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Figure 5-5 Power cable between the DC power distribution box and the fan subrack
View A 1
A1
A2
A3
2 View B
W1
W2
A1
A2
A3
X2
X1
(1) 3V3 power connector
Pin Assignment
Table 5-12 lists the pin assignment of the cable between the DC power distribution box and the
fan subrack.
Table 5-12 Pin assignment of the cable between the DC power distribution box and the fan
subrack
Core Wire
X1 End
X2 End
Core Color
W1
X1.A1
X2.A1
Black
W2
X1.A3
X2.A3
Blue
Installation Positions
Table 5-13 lists the installation positions of the cable between the DC power distribution box
and the fan subrack.
Table 5-13 Installation positions of the cable between the DC power distribution box and the
fan subrack
Cable Name
Function
The power cable between the DC power distribution box and the fan filter unit leads the power
to the control board of the fan filter unit.
Issue 01 (2007-09-10)
5-25
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Appearance
Figure 5-6 shows the structure of the power cable between the DC power distribution box and
the fan filter unit.
Figure 5-6 Power cable between the DC power distribution box and the fan filter unit
2 View B
View A 1
A1
A2
A3
W1
W2
A1
A2
A3
X2
X1
(1) 3V3 power connector
Pin Assignment
Table 5-14 lists the pin assignment of the power cable between the DC power distribution box
and the fan filter unit.
Table 5-14 Pin assignment of the power cable between the DC power distribution box and the
fan filter unit
Wire
X1 End
X2 End
Wire Color
W1
X1.A1
X2.A1
Black
W2
X1.A3
X2.A3
Blue
Installation Positions
Table 5-15 lists the installation positions of the power cable between the DC power distribution
box and the fan filter unit.
Table 5-15 Installation positions of the power cable between the DC power distribution box and
the fan filter unit
Cable Name
Power cable
between the DC
power distribution
box and the fan filter
unit
5-26
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Function
The 75-ohm E1 cable and 120-ohm cable are used to transmit the E1 trunk signal outside the
cabinet.
Structure
The 75-ohm E1 cable is a coaxial cable that consists of eight sub coaxial cables. Every two sub
coaxial cables form one E1 route. Therefore, each 75-ohm E1 cable provides four E1 routes.
The 75-ohm cable uses a DB25 male connector at one end. The other end of the cable is bare.
The connectors should be made on site. Figure 5-7 shows the 75-ohm E1 cable.
Issue 01 (2007-09-10)
5-27
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
W1
W2
W3
W4
W5
Pos.1
W6
X0
W7
W8
A
X1
X2
X3
X4
X5
X6
X7
X8
Pos.25
The 120-ohm E1 cable consists of four pairs of 120-ohm twisted pairs. Each pair forms one E1
route. Therefore, each 120-ohm E1 cable provides four E1 routes. The 120-ohm cable uses a
DB25 male connector at one end. The other end of the cable is bare. The connectors should be
made on site. Figure 5-8 shows the structure of the cable.
Figure 5-8 Structure of the 120-ohm E1 cable
Pin Assignment
Table 5-16 describes the pin assignment for the 75-ohm E1 cable and the 120-ohm cable.
5-28
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Coaxial Cable
Label
W1
X1.tip
X0.24
CHAN 0 TX
X1.ring
X0.25
X2.tip
X0.13
X2.ring
X0.12
X3.tip
X0.11
X3.ring
X0.10
X4.tip
X0.9
X4.ring
X0.8
X5.tip
X0.7
X5.ring
X0.6
X6.tip
X0.5
X6.ring
X0.4
X7.tip
X0.3
X7.ring
X0.2
X8.tip
X0.14
X8.ring
X0.15
W2
W3
W4
W5
W6
W7
W8
CHAN 0 RX
CHAN 1 TX
CHAN 1 RX
CHAN 2 TX
CHAN 2 RX
CHAN 3 TX
CHAN 3 RX
Installation Positions
The installation positions of the 75-ohm E1 cable and 120-ohm cable in the BTS3012/
BTS3012AE are same, as shown in Table 5-17.
Table 5-17 Installation positions of the E1 cable
Issue 01 (2007-09-10)
Cable Type
BTS Type
75-ohm/120ohm E1 cable
BTS3012
Connects to a
transmission device such
as an internal transmission
interface box
BTS3012AE
Connects to a
transmission device such
as an internal transmission
interface box
5-29
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Functions
The optical cables are used to transmit optical signals between the cabinet and other devices.
The optical cable of the BTS3012/BTS3012AE uses the multi-mode fibers for short-distance
transmission.
Structure
Both ends of the multi-mode optical fiber are LC connectors. Figure 5-9 shows the structure of
the optical cable.
Figure 5-9 Structure of the optical cable
(3) LC connector
CAUTION
Apply a protective cap when the optical cable connector is not used.
Pin Assignment
None.
Installation Positions
Table 5-18 describes the installation positions of the optical cable.
5-30
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
One End
Optical cable
Function
The Ethernet cables include the straight-through cable and crossover cable. They are used to
transmit maintenance signals.
l
The straight-through cable connects the PC where the site maintenance terminal system is
installed to the network.
The crossover cable directly connects the PC where the site maintenance terminal system
is installed to the BTS.
Structure
The crossover cable and straight-through cable use the same connector. However, they differ in
connector wiring. The Ethernet cable use RJ45 connectors on both ends, as shown in Figure
5-10.
Figure 5-10 Structure of the Ethernet cable
W
1
X1
X2
Pin Assignment
Table 5-19 describes the pin assignment for the Ethernet cable.
Table 5-19 Pin assignment for the Ethernet cable
Issue 01 (2007-09-10)
X1 End
Core Color
Core Type
X2 End of
the
StraightThrough
Cable
X2 End of the
Crossover
Cable
X1.2
Orange
Twisted pair
X2.2
X2.6
X1.1
X2.1
X2.3
5-31
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
X1 End
Core Color
Core Type
X2 End of
the
StraightThrough
Cable
X2 End of the
Crossover
Cable
X1.6
Green
Twisted pair
X2.6
X2.2
X1.3
X2.3
X2.1
X1.4
Blue
X2.4
X2.4
X1.5
X2.5
X2.5
X1.8
Brown
X2.8
X2.8
X1.7
X2.7
X2.7
Twisted pair
Twisted pair
Installation Positions
The installation positions of the straight-through cable and crossover cable are same, as shown
in Table 5-20.
Table 5-20 Installation positions of the Ethernet cables
Type
One End
Other End
Straightthrough
cable
Crossover
cable
Functions
The E1 signal transfer cable transfers four routes of E1 signals from the DSCB to the DCCU of
the cabinet.
Appearance
Figure 5-11 shows the structure of the E1 signal transfer cable.
5-32
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Pos.1
B
Delander
X2
Pos.36
X1
Pin Assignment
Table 5-21 lists the pin assignment of the E1 signal transfer cable.
Table 5-21 Pin assignment of the E1 signal transfer cable
Issue 01 (2007-09-10)
Wire
Wire Type
X1.6
X2.11
Twisted pair
X1.7
X2.9
X1.24
X2.27
X1.25
X2.25
X1.8
X2.15
X1.9
X2.13
X1.26
X2.31
X1.27
X2.29
X1.2
X2.43
X1.3
X2.41
X1.20
X2.59
X1.21
X2.57
X1.4
X2.47
X1.5
X2.45
X1.22
X2. 63
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
5-33
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Wire
X1.23
X2. 61
X1.14
X2.3
X1.15
X2.1
X1.32
X2.19
X1.33
X2.17
X1.16
X2.7
X1.17
X2.5
X1.34
X2.23
X1.35
X2.21
X1.10
X2.32
X1.11
X2.33
X1.28
X2.51
X1.29
X2.49
X1.12
X2.39
X1.13
X2.37
X1.30
X2.55
X1.31
X2.53
Shell
Shell
Wire Type
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Shield
Installation Positions
Table 5-22 shows the installation positions of the E1 signal transfer cable.
Table 5-22 Installation positions of the E1 signal transfer cable
Cable
E1 signal
transfer cable
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
between the DCCU and the DSCB, TOP2 signals between the DCCU and the DSCB,
environment monitoring signals, RET control signals, monitoring transfer signals between the
NPMI and the DSCB, transfer signals between combined cabinets, PMU monitoring signals,
battery MCB alarm signals, AC lightning arrester alarm signals, humidity and temperature sensor
signals, door control sensor signals, smoke sensor signals, and water sensor signals.
5.5.1 Combining Short-Circuiting Signal Cable of the BTS3012/BTS3012AE
This part describes the function, structure, pin assignment, and installation positions of the
combining short-circuiting signal cable.
5.5.2 Power Detection Cable of the BTS3012/BTS3012AE
This part describes the function, structure, pin assignment, and installation positions of the power
detection cable.
5.5.3 Signal Cable for Combined Cabinets of the BTS3012/BTS3012AE
This part describes the function, structure, pin assignment, and installation positions for the
signal cable for combined cabinets.
5.5.4 Signal Cable for Cabinet Groups of the BTS3012/BTS3012AE
This part describes the function, structure, pin assignment, and installation positions of the signal
cable for cabinet groups.
5.5.5 Far Signal Cable Between BTS3012AE Cabinet Groups
The far signal cable between cabinet groups is used to transmit clock signals between cabinet
groups when the distance between the cabinet groups is 25 meters.
5.5.6 Boolean Input Cable of the BTS3012AE
The Boolean input cables are used to transmit control signals from the BTS3012AE to the other
devices so that the BTS3012AE can control the devices. The Boolean input cables of the
BTS3012AE can provide six Boolean signal outputs.
5.5.7 Signal Cables Between the DSCB and the DAFU Subrack in the BTS3012AE
The signal cables between the DSCB and the DAFU subrack transmit signals from the DSCB
to the DDPU/DFCU/DCOM in the DAFU subrack. There are two signal cables between the
DSCB and the DAFU subrack: one is from the DSCB to the modules in DAFU 0DAFU 2
subracks, and the other is from the DSCB to the modules in DAFU 3DAFU 5 subracks.
5.5.8 TOP1 Signal Cable Between the DCCU and the DSCB in the BTS3012AE
The TOP1 signal cable between the DCCU and the DSCB connects the DTMU and the DSCB.
The TOP1 signal cable transmits lightning protection signals collected by all the lightning
protection boards in the DSCB to the DTMU.
5.5.9 TOP2 Signal Cable Between the DCSU and the DSCB in the BTS3012AE
The TOP2 signal cable between the DCSU and the DSCB connects the DCSU and the DSCB.
The TOP2 signal cable transmits lightning protection signals collected by all the lightning
protection boards in the DSCB to the DCSU.
5.5.10 Signal Cable Between the DCSU and the DTRB in the BTS3012/BTS3012AE
This part describes the function, structure, pin assignment, and installation positions of the signal
cable between the DCSU and the DTRB.
5.5.11 Signal Transfer Cable Between BTS3012AE Combined Cabinets
The signal transfer cable between combined cabinets connects the common subrack and the
signal lightning protection subrack. The cable transmits the Boolean value alarm signals from
the signal lightning protection subrack to the common subrack.
5.5.12 RS485 Environment Monitoring Signal Cable for the BTS3012AE
Issue 01 (2007-09-10)
5-35
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
The RS485 environment monitoring signal cable transfers the RS485 monitoring signals in the
BTS3012AE cabinet. The RS485 environment monitoring signal cable transfers the
environment monitoring signals to the DCCU. The environment monitoring signals are collected
from the PMU, fan subrack, fan filter unit, and sensors.
5.5.13 RET Control Signal Cable of the BTS3012/BTS3012AE
This part describes the function, structure, pin assignment, and installation positions of the RET
control signal cable.
5.5.14 Monitoring Transfer Signal Cable Between the NPMI and the DSCB in the BTS3012AE
The monitoring transfer signal cable between the NPMI and the DSCB connects the NPMI and
the DSCB. The cable transmits the alarm information collected by the NPMI to the DSCB.
5.5.15 Diversity Receive Short-Circuiting Cable of the BTS3012/BTS3012AE
This part describes the function, structure, pin assignment, and installation positions of the
diversity receive short-circuiting cable.
5.5.16 Four-In-One Short-Circuiting Cable of the BTS3012/BTS3012AE
This cable describes the function, structure, pin assignment, and installation positions of the
four-in-one short-circuiting cable.
5.5.17 Signal Cable Between the DFCB and the DFCU in the BTS3012/BTS3012AE
This part describes the function, structure, pin assignment, and installation positions of the signal
cable between the DFCB and the DFCU.
5.5.18 DPMU Monitoring Cable for the BTS3012AE
The DPMU monitoring cable connects the NPMI and the DPMU. It transmits the sensor signals
collected by the NPMI to the DPMU.
5.5.19 Alarm Cable for the MCB of the BTS3012AE Battery
The alarm cable for the MCB of the BTS3012AE battery connects the battery and the NPMI. It
transmits the voltage information about the battery to the NPMI.
5.5.20 Alarm Cable for the BTS3012AE Lightning Arrester
The alarm cable for the lightning arrester connects the AC lightning arrester and the NPMI. It
transmits the information about the lightning arrester to the NPMI.
5.5.21 Signal Cable for the Humidity and Temperature Sensor of the BTS3012AE
The signal cable for the humidity and temperature sensor connects the humidity and temperature
sensor and the NPMI. It transmits the information about the humidity and temperature of the
battery cabin from the humidity and temperature sensor to the NPMI.
5.5.22 Signal Cable for the Door Control Sensor of the BTS3012AE
The signal cable for the door control sensor connects the door control sensor and the NPMI. It
transmits the open and close information about the door from the door control sensor to the
NPMI.
5.5.23 Signal Cable for the Smoke Sensor of the BTS3012AE
The signal cable for the smoke sensor connects the smoke sensor and the NPMI. It transmits the
smoke information collected by the smoke sensor to the NPMI.
5.5.24 Cable for the Water Sensor of the BTS3012AE
The signal cable for the water sensor connects the water sensor and the NPMI. It transmits the
water information collected by the water sensor to the NPMI.
5-36
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Function
This cable is used to achieve the combination output of RF signals by connecting the TX port
with the IN port on the DTRU (type A).
Structure
Figure 5-12 shows the structure of the combining short-circuiting signal cable.
Figure 5-12 Structure of the combining short-circuiting signal cable
W
3
1
2
(3) Label
Pin Assignment
None.
Installation Positions
Table 5-23 describes the installation positions of the combining short-circuiting signal cable.
Table 5-23 Installation positions of the combining short-circuiting signal cable
Cable Type
5-37
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Function
The power detection cable transmits the RF signal sent from the coupling unit in the DFCU/
DFCB to the power detection unit. This cable can be categorized into forward power detection
cable and reverse power detection cable. The forward power detection cable has the same
structure as the reverse power detection cable.
Structure
Figure 5-13 shows the structure of the power detection cable.
Figure 5-13 Structure of the power detection cable
1
1
RF Rx Cable
Pin Assignment
None.
Installation Positions
Table 5-24 describes the installation positions of the power detection cable.
Table 5-24 Installation positions of the power detection cable
Cable
One End
Other End
Forward power
detection cable
Reverse power
detection cable
Function
The signal cable for combined cabinets is used to transmit the signals between two combined
cabinets.
Structure
Figure 5-14 shows the structure of the signal cable for combined cabinets.
5-38
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Pin Assignment
Table 5-25 describes the pin assignment for the signal cable for combined cabinets.
Table 5-25 Pins assignment for the signal cable for combined cabinets
Issue 01 (2007-09-10)
Core Type
X1.2
X2.2
Twisted pair
X1.3
X2.3
X1.4
X2.4
X1.5
X2.5
X1.7
X2.7
X1.8
X2.8
X1.9
X2.9
X1.10
X2.10
X1.36
X2.36
X1.37
X2.37
X1.38
X2.38
X1.39
X2.39
X1.41
X2.41
X1.42
X2.42
Huawei Technologies Proprietary
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
5-39
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
5-40
Core Type
X1.43
X2.43
Twisted pair
X1.44
X2.44
X1.46
X2.46
X1.47
X2.47
X1.48
X2.48
X1.49
X2.49
X1.22
X2.22
X1.23
X2.23
X1.25
X2.25
X1.26
X2.26
X1.51
X2.51
X1.52
X2.52
X1.53
X2.53
X1.54
X2.54
X1.28
X2.28
X1.29
X2.29
X1.30
X2.30
X1.31
X2.31
X1.56
X2.56
X1.57
X2.57
X1.59
X2.59
X1.60
X2.60
X1.12
X2.12
X1.13
X2.13
X1.14
X2.14
X1.15
X2.15
X1.62
X2.62
X1.63
X2.63
X1.64
X2.64
X1.65
X2.65
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Core Type
X1.17
X2.17
Twisted pair
X1.18
X2.18
X1.19
X2.19
X1.20
X2.20
Twisted pair
Installation Positions
Table 5-26 describes the installation positions of the signal cable for combined cabinets.
Table 5-26 Installation positions of the signal cable for combined cabinets
Cabinet Type
BTS3012
BTS3012AE
Function
The signal cable for cabinet groups is used to transmit signals between the cabinet groups.
Structure
Figure 5-15 shows the structure of the signal cable for cabinet groups.
Figure 5-15 Structure of the signal cable for cabinet groups
Pos.1
Pos.36
X1
Issue 01 (2007-09-10)
X2
5-41
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Pin Assignment
Table 5-27 describes the pin assignment for the signal cable for cabinet groups.
Table 5-27 Pin assignment for the signal cable for cabinet groups
5-42
Wire Type
X1.1
X2.1
Twisted pair
X1.19
X2.19
X1.20
X2.2
X1.21
X2.3
X1.22
X2.4
X1.23
X2.5
X1.24
X2.6
X1.25
X2.7
X1.26
X2.8
X1.27
X2.9
X1.29
X2.11
X1.30
X2.12
X1.31
X2.13
X1.32
X2.14
X1.33
X2.15
X1.34
X2.16
X1.35
X2.17
X1.36
X2.18
X1.2
X2.20
X1.3
X2.21
X1.4
X2.22
X1.5
X2.23
X1.6
X2.24
X1.7
X2.25
X1.8
X2.26
X1.9
X2.27
X1.11
X2.29
Huawei Technologies Proprietary
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
X1.12
X2.30
X1.13
X2.31
X1.14
X2.32
X1.15
X2.33
X1.16
X2.34
X1.17
X2.35
X1.18
X2.36
Wire Type
Twisted pair
Twisted pair
Twisted pair
Installation Positions
Table 5-28 describes the installation positions of the signal cable for cabinet groups.
Table 5-28 Installation positions of the signal cable for cabinet groups
Cable Type
BTS Type
Signal cable
for cabinet
groups
BTS3012
BTS3012AE
Connects to the TO
SLAVE GROUP1 or TO
SLAVE GROUP2 port on
the DSCB of one main
cabinet in the cabinet group
Functions
The far signal cable between cabinet groups is used to transmit clock signals between cabinet
groups when the distance between the cabinet groups is 25 meters.
Appearance
Figure 5-16 shows the structure of the far signal cable between cabinet groups.
Issue 01 (2007-09-10)
5-43
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Pos.1
Pos.25
X1
X2
Pin Assignment
Table 5-29 lists the pin assignment for the signal cable between cabinet groups.
Table 5-29 Pins assignment for the signal cable between cabinet groups
5-44
Wire Type
X1.1
X2.1
Twisted pair
X1.16
X2.16
X1.2
X2.2
X1.3
X2.3
X1.4
X2.4
X1.5
X2.5
X1.6
X2.6
X1.7
X2.7
X1.8
X2.8
X1.9
X2.9
X1.10
X2.10
X1.11
X2.11
X1.12
X2.12
X1.13
X2.13
X1.14
X2.14
X1.14
X2.15
X1.24
X2.24
X1.25
X2.25
Huawei Technologies Proprietary
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Wire Type
Shell
Shell
Shield
Installation Positions
Table 5-30 describes the installation positions of the far signal cable between cabinet groups.
Table 5-30 Installation positions of far signal cable between cabinet groups
Signal Cable
Function
The Boolean input cables are used to transmit control signals from the BTS3012AE to the other
devices so that the BTS3012AE can control the devices.
Appearance
One end of the cable is a DB44 male connector, and the other end is bare. Figure 5-17 shows
the Boolean input cable
.
Figure 5-17 Boolean input cable
1
View A POS.1
X1
W
POS.44
Issue 01 (2007-09-10)
5-45
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Pin Description
Table 5-31 lists the pin assignment of the Boolean value input cable.
Table 5-31 Pin assignment of the Boolean input cable
Pin of the
Connector
Wire Type
Wire Color
Alarm Input
Serial Number
X1.1
Twisted pair
Blue
Alarm input 6
(provided by the
DTMU)
X1.17
X1.2
White
Twisted pair
X1.18
X1.3
White
Twisted pair
X1.19
X1.4
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Blue
Black
Twisted pair
X1.27
5-46
Grey
Red
X1.26
X1.12
Brown
Red
X1.25
X1.11
Green
Red
X1.24
X1.10
Orange
Red
X1.38
X1.9
Blue
Red
X1.23
X1.8
Grey
White
X1.22
X1.7
Brown
White
X1.21
X1.6
Green
White
X1.20
X1.5
Orange
Orange
Black
Alarm input 2
(provided by the
DTMU)
Alarm input 1
(provided by the
DTMU)
Alarm input 4
(provided by the
DTMU)
Alarm input 3
(provided by the
DTMU)
Alarm input 5
(provided by the
DTMU)
Alarm input 7
(provided by the
DTMU)
Alarm input 1
(provided by the
NPMI)
Alarm input 8
(provided by the
DTMU)
Alarm input 2
(provided by the
NPMI)
Alarm input 5
(provided by the
NPMI)
Alarm input 4
(provided by the
NPMI)
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Pin of the
Connector
Wire Type
Wire Color
Alarm Input
Serial Number
X1.13
Twisted pair
Green
Alarm input 6
(provided by the
NPMI)
X1.28
X1.14
Black
Twisted pair
X1.29
X1.34
Twisted pair
X1.35
X1.36
Black
Alarm input 7
(provided by the
NPMI)
Grey
Black
Twisted pair
X1.37
Shell
Brown
Blue
Yellow
Shield
Installation Positions
Table 5-32 describes the installation positions of the Boolean value input cable.
Table 5-32 Installation positions of the Boolean input cable
Signal Cable
Boolean input
cable
5.5.7 Signal Cables Between the DSCB and the DAFU Subrack in
the BTS3012AE
The signal cables between the DSCB and the DAFU subrack transmit signals from the DSCB
to the DDPU/DFCU/DCOM in the DAFU subrack. There are two signal cables between the
DSCB and the DAFU subrack: one is from the DSCB to the modules in DAFU 0DAFU 2
subracks, and the other is from the DSCB to the modules in DAFU 3DAFU 5 subracks.
Functions
The signal cables between the DSCB and the DAFU subrack transmit signals from the DSCB
to the DDPU/DFCU/DCOM in the DAFU subrack.
Appearance
The two signal cables between the DSCB and the DAFU subrack have the same appearance and
structure. Figure 5-18 shows the signal cable.
Issue 01 (2007-09-10)
5-47
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Figure 5-18 Signal cable between the DSCB and the DAFU subrack
1
B
2
W1
W2
W3
View A
Pos.1
X2
X3
View B
Pos.26
X4
Pos.1
Pos.68
Pin Assignment
The pins of the two cables between the DSCB and the DAFU subrack are the same. Table
5-33 lists the pin assignment for one signal cable between the DSCB and the DAFU subrack.
Table 5-33 Pins assignment for the signal cable between the DSCB and the DAFU subrack
5-48
Signal
Cable
Wire Type
W1
X1.1
X2.7
Twisted pair
X1.2
X2.8
X1.3
X2.11
X1.4
X2.10
X1.35
X2.20
X1.36
X2.19
X1.37
X2.13
X1.38
X2.12
X1.5
X2.16
X1.6
X2.9
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
Signal
Cable
W2
W3
Issue 01 (2007-09-10)
5 BTS3012AE Cables
Wire Type
X1.7
X2.17
Twisted pair
X1.8
X2.18
X1.39
X2.15
X1.40
X2.26
X1.41
X2.24
X1.42
X2.25
X1.13
X3.7
X1.14
X3.8
X1.15
X3.11
X1.16
X3.10
X1.47
X3.20
X1.48
X3.19
X1.49
X3.13
X1.50
X3.12
X1.17
X3.9
X1.18
X3.16
X1.19
X3.17
X1.20
X3.18
X1.51
X3.15
X1.52
X3.24
X1.53
X3.26
X1.54
X3.25
X1.25
X4.7
X1.26
X4.8
X1.27
X4.11
X1.28
X4.10
X1.59
X4.20
X1.60
X4.19
X1.61
X4.13
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
5-49
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Signal
Cable
X1.62
X4.12
X1.29
X4.9
X1.30
X4.17
X1.31
X4.16
X1.32
X4.18
X1.63
X4.15
X1.64
X4.26
X1.65
X4.24
X1.66
X4.25
Wire Type
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Installation Positions
Table 5-34 lists the installation positions of the two signal cables between the DSCB and the
DAFU subrack.
Table 5-34 Installation positions of the signal cables between the DSCB and the DAFU subrack
Signal Cable
Signal cable
between the
DSCB and
DAFU0DAFU2
in the DAFU
subrack
Connects to port
TO DAFU 0-2 on
the DSCB
Signal cable
between the
DSCB and
DAFU3DAFU5
in the DAFU
subrack
Connects to port
TO DAFU 3-5 on
the DSCB
5-50
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
5.5.8 TOP1 Signal Cable Between the DCCU and the DSCB in the
BTS3012AE
The TOP1 signal cable between the DCCU and the DSCB connects the DTMU and the DSCB.
The TOP1 signal cable transmits lightning protection signals collected by all the lightning
protection boards in the DSCB to the DTMU.
Functions
The TOP1 signal cable between the DCCU and the DSCB connects the DTMU and the DSCB.
The TOP1 signal cable transmits lightning protection signals collected by all the lightning
protection boards in the DSCB to the DTMU.
Appearance
Figure 5-19 shows the TOP1 signal cable between the DCCU and the DSCB.
Figure 5-19 TOP1 signal cable between the DCCU and the DSCB
View B
Pos.64
2
View A
Pos.1
Pos.1
Delander
X2
Pos.68
X1
Pin Assignment
Table 5-35 lists the pin assignment of the TOP1 signal cable between the DCCU and the DSCB.
Table 5-35 Pin assignment of the TOP1 signal cable between the DCCU and the DSCB
Issue 01 (2007-09-10)
Signal Cable
Wire Type
X1.5
X2.35
Twisted pair
X1.6
X2.36
X1.7
X2.37
Huawei Technologies Proprietary
Twisted pair
5-51
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Signal Cable
5-52
X1.8
X2.38
X1.9
X2.11
X1.10
X2.12
X1.11
X2.15
X1.12
X2.16
X1.13
X2.3
X1.14
X2.4
X1.15
X2. 7
X1.16
X2.8
X1.17
X2.13
X1.18
X2.14
X1.19
X2.30
X1.20
X2.29
X1.21
X2.5
X1.22
X2.6
X1.23
X2.9
X1.24
X2.10
X1.25
X2.23
X1.26
X2.24
X1.27
X2.27
X1.28
X2.28
X1.29
X2.19
X1.30
X2.20
X1.31
X2.21
X1.32
X2.22
X1.33
X2.56
X1.66
X2.55
X1.38
X2.58
X1.39
X2.57
Wire Type
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
Signal Cable
Issue 01 (2007-09-10)
5 BTS3012AE Cables
Wire Type
X1.40
X2.60
Twisted pair
X1.41
X2.59
X1.42
X2.54
X1.43
X2.53
X1.44
X2.49
X1.45
X2.50
X1.46
X2.44
X1.47
X2.43
X1.48
X2.64
X1.49
X2.63
X1.50
X2.52
X1.51
X2.51
X1.52
X2.33
X1.53
X2.34
X1.54
X2.32
X1.55
X2.31
X1.56
X2.48
X1.57
X2.47
X1.58
X2.17
X1.59
X2.18
X1.60
X2.1
X1.61
X2.2
X1.62
X2.46
X1.63
X2.45
X1.64
X2.62
X1.65
X2.61
X1.2
X2.25
X1.3
X2.40
X1.4
X2.39
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
5-53
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Signal Cable
W.Shield
Wire Type
X1.36
X2.26
X1.37
X2.41
X1.1
Shield
X1.34
X1.35
X1.68
X1.Shell
X2.42
X2.Shell
Installation Positions
Table 5-36 lists the installation positions of the TOP1 signal cable between the DCCU and the
DSCB.
Table 5-36 Installation positions of the TOP1 signal cable between the DCCU and the DSCB
Signal Cable
5.5.9 TOP2 Signal Cable Between the DCSU and the DSCB in the
BTS3012AE
The TOP2 signal cable between the DCSU and the DSCB connects the DCSU and the DSCB.
The TOP2 signal cable transmits lightning protection signals collected by all the lightning
protection boards in the DSCB to the DCSU.
Functions
The TOP2 signal cable between the DCSU and the DSCB connects the DCSU and the DSCB.
The TOP2 signal cable transmits lightning protection signals collected by all the lightning
protection boards in the DSCB to the DCSU.
Appearance
Figure 5-20 shows the TOP2 signal cable between the DCSU and the DSCB.
5-54
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Figure 5-20 TOP2 signal cable between the DCSU and the DSCB
View A
Pos.1
2
W
A
Pos.26
View B
Pos.1
B
X1
X3
Pos.36
Pin Assignment
Table 5-37 lists the pin assignment of the TOP2 signal cable between the DCSU and the DSCB.
Table 5-37 Pin assignment of the TOP2 signal cable between the DCSU and the DSCB
Wire
Wire Type
X1.16
X2.6
X1.12
X2.7
X1.11
X2.8
X1.10
X2.9
X1.8
X2.10
Twisted pair
X1.9
X2.28
X1.3
X2.11
X1.1
X2.12
X1.17
X2.24
X1.15
X2.25
X1.14
X2.26
X1.13
X2.27
X1.2
X2.29
X1.4
X2.14
Shield
X1.7
X2.21
X1.Shell
X2.Shell
Installation Positions
Table 5-38 lists the installation positions of the TOP2 signal cable between the DCSU and the
DSCB.
Issue 01 (2007-09-10)
5-55
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Table 5-38 Installation positions of the TOP2 signal cable between the DCSU and the DSCB
Signal Cable
5.5.10 Signal Cable Between the DCSU and the DTRB in the
BTS3012/BTS3012AE
This part describes the function, structure, pin assignment, and installation positions of the signal
cable between the DCSU and the DTRB.
Function
The signal cable between the DCSU and the DTRB is used to transmit signals between the DTRU
and the DCSU. The signals include the data bus signals, clock bus signals, CBUS2 signals, and
in-position signals.
Structure
Figure 5-21 shows the structure of the signal cable between the DCSU and the DTRB.
Figure 5-21 Structure of the signal cable between the DCSU and the DTRB
Pos.1
View A
View B
Pos.68
Pos.64
A
Pos.1
B
Delander
W
X1
X2
Pin Assignment
Table 5-39 describes the pin assignment for the signal cable between the DCSU and the DTRB.
5-56
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Table 5-39 Pin assignment for the signal cable between the DCSU and the DTRB
Issue 01 (2007-09-10)
Cable
Wire Type
X1.1
X2.1
Twisted pair
X1.2
X2.2
X1.3
X2.35
X1.4
X2.36
X1.5
X2.3
X1.6
X2.46
X1.7
X2.4
X1.8
X2.5
X1.9
X2.38
X1.10
X2.39
X1.11
X2.6
X1.12
X2.40
X1.13
X2.7
X1.14
X2.8
X1.15
X2.41
X1.16
X2.42
X1.17
X2.10
X1.18
X2.11
X1.19
X2.44
X1.20
X2.45
X1.21
X2.21
X1.22
X2.26
X1.23
X2.13
X1.24
X2.14
X1.25
X2.47
X1.26
X2.48
X1.27
X2.55
X1.28
X2.60
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
5-57
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Cable
5-58
Wire Type
X1.29
X2.16
Twisted pair
X1.30
X2.17
X1.31
X2.50
X1.32
X2.51
X1.33
X2.19
X1.34
X2.20
X1.35
X2.53
X1.36
X2.54
X1.37
X2.18
X1.38
X2.52
X1.39
X2.22
X1.40
X2.23
X1.41
X2.25
X1.42
X2.59
X1.43
X2.37
X1.44
X2.49
X1.45
X2.27
X1.46
X2.28
X1.47
X2.61
X1.48
X2.62
X1.49
X2.30
X1.50
X2.31
X1.51
X2.64
X1.52
X2.65
X1.55
X2.58
X1.56
X2.56
X1.57
X2.24
X1.58
X2.57
X1.59
X2.32
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
Cable
5 BTS3012AE Cables
X1.60
X2.66
X1.61
X2.33
X1.62
X2.34
X1.63
X2.67
X1.64
X2.68
X1.53
X2.63
Wire Type
Twisted pair
Twisted pair
Twisted pair
Installation Positions
Table 5-40 describes the installation positions of the signal cable between the DCSU and the
DTRB.
Table 5-40 Installation positions of the signal cable between the DCSU and the DTRB
Cable
Signal cable
between the
DCSU and the
DTRB
Functions
The signal transfer cable between combined cabinets connects the common subrack and the
signal lightning protection subrack. The cable transmits the Boolean value alarm signals from
the signal lightning protection subrack to the common subrack.
Appearance
Figure 5-22 shows the signal transfer cable between combined cabinets.
Issue 01 (2007-09-10)
5-59
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
View A
Pos.1
Pos.1
Delander
X2
Pos.68
X1
Pin Assignment
Table 5-41 lists the pin assignment of the signal transfer cable between combined cabinets.
Table 5-41 Pin assignment of the signal transfer cable between combined cabinets
5-60
Wire
Wire Type
X1.13
X2.32
Twisted pair
X1.14
X2.31
X1.15
X2.30
X1.16
X2.29
X1.17
X2.16
X1.18
X2.15
X1.19
X2.14
X1.20
X2.13
X1.21
X2.40
X1.22
X2.39
X1.23
X2. 36
X1.24
X2.35
X1.25
X2.34
X1.26
X2.33
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
Wire
Issue 01 (2007-09-10)
5 BTS3012AE Cables
Wire Type
X1.27
X2.58
Twisted pair
X1.28
X2.57
X1.29
X2.56
X1.30
X2.55
X1.31
X2.4
X1.32
X2.3
X1.33
X2.2
X1.34
X2.1
X1.45
X2.52
X1.46
X2.51
X1.47
X2.50
X1.48
X2.49
X1.49
X2.64
X1.50
X2.63
X1.51
X2.62
X1.52
X2.61
X1.53
X2.48
X1.54
X2.47
X1.55
X2.46
X1.56
X2.45
X1.57
X2.26
X1.58
X2.25
X1.59
X2.24
X1.60
X2.23
X1.61
X2.20
X1.62
X2.19
X1.63
X2.18
X1.64
X2.17
X1.65
X2.10
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
5-61
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Wire
Wire Type
X1.66
X2.9
X1.67
X2.8
X1.68
X2.7
X1.6
X2.5
X1.7
X2.6
X1.8
X2.11
X1.9
X2.12
X1.5
X2.21
Shield
X1.10
X2.22
X1.39
X2.27
X1.40
X2.28
X1.41
X2.59
X1.44
X2.60
X1.Shell
X2.Shell
Twisted pair
Installation Positions
Table 5-42 lists the installation positions of the signal transfer cable between combined cabinets.
Table 5-42 Installation positions of the signal transfer cable between combined cabinets
Signal Cable
Signal transfer
cable between
BTS3012AE
combined
cabinets
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
environment monitoring signals to the DCCU. The environment monitoring signals are collected
from the PMU, fan subrack, fan filter unit, and sensors.
Function
The RS485 environment monitoring signal cable transfers the RS485 monitoring signals in the
BTS3012AE cabinet. The RS485 environment monitoring signal cable transfers the
environment monitoring signals to the DCCU. The environment monitoring signals are collected
from the PMU, fan subrack, fan filter unit, and sensors.
Appearance
Figure 5-23 shows the RS485 environment monitoring signal cable.
Figure 5-23 RS485 environment monitoring signal cable
View B
2
W1
B
1
X2
View A
Pos.1
W2
A
X1
Pos.26
X3
4
View E
1
2
3
4
5
View C
3
Pos.1
W3
Pos.15
View D
Pos.1
D
W4
X5
X4
Pos.26
Pin Assignment
Table 5-43 lists the pin assignment of W1 shown in Figure 5-23.
Table 5-43 Pin assignment of W1
Issue 01 (2007-09-10)
Wire
Wire Type
W1
X1.19
X2.1
Twisted pair
X1.11
X2.2
X1.1
X2.4
X1.10
X2.5
Huawei Technologies Proprietary
Twisted pair
5-63
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Wire
Wire Type
X1.Shell
X2.Shell
Shield
Description
W2
X1.19
X3.1
Twisted pair
X1.11
X3.2
X1.1
X3.4
X1.10
X3.5
X1.Shell
X3.Shell
Twisted pair
Shield
5-64
Wire
Description
W3
X1.1
X4.1
Twisted pair
X1.10
X4.10
X1.2
X4.2
X1.3
X4.3
X1.4
X4.4
X1.5
X4.5
X1.6
X4.6
X1.7
X4.7
X1.11
X4.11
X1.19
X4.19
X1.13
X4.13
X1.14
X4.14
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Wire
Description
X1.12
X4.12
Twisted pair
X1.16
X4.16
X1.17
X4.17
X1.12
X4.12
X1.20
X4.20
X1.21
X4.21
X1.22
X4.22
X1.23
X4.23
X1.24
X4.24
X1.25
X4.25
X1.Shell
X4.Shell
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Shield
Pin of the X4
End (DB26
Connector)
Pin of the X5
End (Common
5-Pin
Connector)
Description
Wire Color
W4
X4.8
X5.1
Twisted pair
Black
X4.9
X5.2
X4.18
X5.3
X4.Shell
Shield
Installation Positions
Table 5-47 lists the installation positions of the RS485 environment monitoring signal cable.
Table 5-47 Installation positions of the RS485 environment monitoring signal cable
Issue 01 (2007-09-10)
Signal Cable
RS485
environment
5-65
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Signal Cable
monitoring signal
cable
Function
The RET control signal cable is used to transmit signals between the DATU and the Bias-Tee.
Structure
Figure 5-24 shows the structure of the RET control signal cable.
Figure 5-24 Structure of the RET control signal cable
2
1
W
X1
X2
Pin Description
None
Installation Positions
Table 5-48 describes the installation positions of the RET control signal cable.
5-66
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
RET control
signal cable
5.5.14 Monitoring Transfer Signal Cable Between the NPMI and the
DSCB in the BTS3012AE
The monitoring transfer signal cable between the NPMI and the DSCB connects the NPMI and
the DSCB. The cable transmits the alarm information collected by the NPMI to the DSCB.
Functions
The monitoring transfer signal cable between the NPMI and the DSCB connects the NPMI and
the DSCB. The cable transmits the alarm information collected by the NPMI to the DSCB.
Appearance
Figure 5-25 shows the monitoring transfer signal cable between the NPMI and the DSCB.
Issue 01 (2007-09-10)
5-67
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Figure 5-25 Monitoring transfer signal cable between the NPMI and the DSCB
1
View A
Lable1
1 A
2
X1
View B
1
2
3
4
Lable2
X2
Lable3
B
X3
Lable4
X4
View C
Pos.1
Lable5
X9
X5
Pos.36
Lable6
X6
Lable7
X7
Lable8
X8
Pin Assignment
Table 5-49 lists the pin assignment of the monitoring transfer signal cable between the NPMI
and the DSCB.
Table 5-49 Pin assignment of the monitoring transfer signal cable between the NPMI and the
DSCB
5-68
Wire
One End
Color
Wire Type
X1.1
X9.6
Blue
Twisted pair
X1.2
X9.7
White
X2.1
X9.8
Orange
X2.2
X9.9
White
X3.4
X9.22
Green
X3.3
X9.24
White
X4.3
X9.25
Brown
Twisted pair
Twisted pair
Twisted pair
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
Wire
5 BTS3012AE Cables
One End
Color
X4.4
X9.31
White
X5.3
X9.26
Grey
X6.3
X9.27
Brown
X7.3
X9.28
Blue
X8.3
X9.29
Red
Wire Type
Twisted pair
Twisted pair
Installation Positions
Table 5-50 lists the installation positions of the monitoring transfer signal cable between the
NPMI and the DSCB.
Table 5-50 Installation positions of the monitoring transfer signal cable between the NPMI and
the DSCB
Signal Cable
One End
Monitoring
transfer signal
cable between the
NPMI and the
DSCB
Function
The diversity receive short-circuiting cable is used to transfer the diversity receive signals from
the antenna subsystem when the DFCU/DFCB is used.
Appearance
Figure 5-26 shows the structure of the diversity receive short-circuiting cable.
Issue 01 (2007-09-10)
5-69
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
RF Rx Cable
Pin Assignment
None.
Installation Positions
Table 5-51 describes the installation positions of the diversity receive short-circuiting cable.
Table 5-51 Installation positions of the diversity receive short-circuiting cable
Cable Type
One End
Other End
Diversity receive
short-circuiting
cable
Function
The four-in-one short-circuiting cable is used to combine four routes of TX signals when the
DFCU or DFCB is used. It can be used to combine six routes of TX signals when the DFCU
and DFCB is cascaded.
Structure
Figure 5-27 shows the structure of the four-in-one short-circuiting cable.
Figure 5-27 Structure of the four-in-one short-circuiting cable
1
1
RF Tx Cable
5-70
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Pin Assignment
None.
Installation Positions
Table 5-52 describes the installation positions of the four-in-one short-circuiting cable.
Table 5-52 Installation positions of the four-in-one short-circuiting cable
Type
One End
Other End
5.5.17 Signal Cable Between the DFCB and the DFCU in the
BTS3012/BTS3012AE
This part describes the function, structure, pin assignment, and installation positions of the signal
cable between the DFCB and the DFCU.
Function
The signal cable between the DFCB and the DFCU is used to transmit two routes of combined
RF signals (two-in-one) to the DFCU so that the DFCU can combine six routes of RF signals
into one route for transmission.
Structure
Figure 5-28 shows the structure of the signal cable between the DFCB and the DFCU.
Figure 5-28 Structure of the signal cable between the DFCB and the DFCU
1
1
RF Tx Cable
Pin Assignment
None.
Issue 01 (2007-09-10)
5-71
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Installation Positions
Table 5-53 describes the installation positions of the signal cable between the DFCB and the
DFCU.
Table 5-53 Installation positions of the signal cable between the DFCB and the DFCU
Type
One End
Other End
Signal cable
between the
DFCB and the
DFCU
Functions
The DPMU monitoring cable connects the NPMI and the DPMU. It transmits the sensor signals
collected by the NPMI to the DPMU.
Appearance
Figure 5-29 shows the DPMU monitoring cable.
Figure 5-29 DPMU monitoring cable
View A
Pos.50
Pos.1
A
2
W
View B
Pos.50
X1
X2
Pos.1
Pin Assignment
Table 5-54 lists the pin assignment of the DPMU monitoring cable.
5-72
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Issue 01 (2007-09-10)
Wire Color
Wire Type
X1.1
X2.1
White
Twisted pair
X1.2
X2.2
Blue
X1.3
X2.3
White
X1.4
X2.4
Orange
X1.5
X2.5
White
X1.8
X2.8
Green
X1.9
X2.9
White
X1.10
X2.10
Brown
X1.11
X2.11
White
X1.12
X2.12
Grey
X1.13
X2.13
Red
X1.14
X2.14
Blue
X1.16
X2.16
Red
X1.17
X2.17
Orange
X1.18
X2.18
Red
X1.19
X2.19
Green
X1.20
X2.20
Red
X1.21
X2.21
Brown
X1.22
X2.22
Red
X1.23
X2.23
Grey
X1.24
X2.24
Black
X1.25
X2.25
Blue
X1.27
X2.27
Black
X1.28
X2.28
Orange
X1.29
X2.29
Black
X1.30
X2.30
Green
X1.31
X2.31
Black
X1.32
X2.32
Brown
X1.33
X2.33
Black
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
Twisted pair
5-73
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Wire Color
X1.34
X2.34
Grey
X1.43
X2.43
Yellow
X1.44
X2.44
Blue
Wire Type
Twisted pair
Installation Positions
Table 5-55 lists the installation positions of the DPMU monitoring cable.
Table 5-55 Installation positions of the DPMU monitoring cable
Signal Cable
DPMU
monitoring
cable
Functions
The alarm cable for the MCB of the BTS3012AE battery connects the battery and the NPMI. It
transmits the voltage information about the battery to the NPMI.
Appearance
Figure 5-30 shows the alarm cable for the MCB of the battery.
Figure 5-30 Alarm cable for the MCB of the battery
1
1
2
2
A
A
(1) Common 2-pin connector
(3) OT terminal
Pin Assignment
None.
5-74
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Installation Positions
Table 5-56 lists the installation positions of the alarm cable for the MCB of the battery.
Table 5-56 Installation positions of the alarm cable for the MCB of the battery
Signal Cable
Functions
The alarm cable for the lightning arrester connects the AC lightning arrester and the NPMI. It
transmits the information about the lightning arrester to the NPMI.
Appearance
Figure 5-31 shows the alarm cable for the lightning arrester.
Figure 5-31 Alarm cable for the lightning arrester
2
1
X2
W1
W2
X1
View A
X3
1
2
3
4
Pin Assignment
None.
Installation Positions
Table 5-57 lists the installation positions of the alarm cable for the lightning arrester.
Issue 01 (2007-09-10)
5-75
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Table 5-57 Installation positions of the alarm cable for the lightning arrester
Cable
Functions
The signal cable for the humidity and temperature sensor connects the humidity and temperature
sensor and the NPMI. It transmits the humidity and temperature information about the battery
cabin from the humidity and temperature sensor to the NPMI.
Appearance
Figure 5-32 shows the signal cable for the humidity and temperature sensor.
Figure 5-32 Signal cable for the humidity and temperature sensor
2
X2
1
W1
A
W4
X1
X3
X4
X5
View A
1
2
3
4
Pin Assignment
Table 5-58 lists the pin assignment of the signal cable for the humidity and temperature sensor.
5-76
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Table 5-58 Pin assignment of the signal cable for the humidity and temperature sensor
Pin of 4-Pin
Connector
Common Connector
Wire Color
X1.1
X2
Red
X1.2
X3
White
X1.3
X4
Red
X1.4
X5
Green
Installation Positions
Table 5-59 lists the installation positions of the signal cable for the humidity and temperature
sensor.
Table 5-59 Installation positions of the signal cable for the humidity and temperature sensor
Signal Cable
Common Connector
5.5.22 Signal Cable for the Door Control Sensor of the BTS3012AE
The signal cable for the door control sensor connects the door control sensor and the NPMI. It
transmits the open and close information about the door from the door control sensor to the
NPMI.
Functions
The signal cable for the door control sensor connects the door control sensor and the NPMI. It
transmits the open and close information about the door from the door control sensor to the
NPMI.
Appearance
Figure 5-33 shows the signal cable for the door control sensor.
Issue 01 (2007-09-10)
5-77
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
W1
X1
3
A
W2
X2
View A
1
2
X3
4
W3
X4
W5
W4
X5
X6
(1) 250-type parallel connector (2) Common 2-pin connector (3) 4-pin connector (4) Heat-shrinkable tube
Pin Assignment
Table 5-60 lists the pin assignment of the signal cable for the door control sensor.
Table 5-60 Pin assignment of the signal cable for the door control sensor
Pin of Parallel
Terminal 250
Pin of 2-Pin
Connector
Wire Color
X1
X3.1
Red
X2
X3.2
Red
Installation Positions
Table 5-61 lists the installation positions of the signal cable for the door control sensor.
Table 5-61 Installation positions of the cable for the door control sensor
Signal Cable
Parallel Terminal
NOTE
Remove W5 in case of combined cabinets, and then connect the cable for the door control sensor on the
other cabinet door to the W5 port.
5-78
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Functions
The signal cable for the smoke sensor connects the smoke sensor and the NPMI. It transmits the
smoke information collected by the smoke sensor to the NPMI.
Appearance
Figure 5-34 shows the signal cable for the smoke sensor.
Figure 5-34 Signal cable for the smoke sensor
2
1
X2
W1
W2
X1
View A
X3
1
2
Pin Assignment
Table 5-62 shows the pin assignment of the signal cable for the smoke sensor.
Table 5-62 Pin assignment of the signal cable for the smoke sensor
Wire
Wire Color
W1
Red
W2
White
Installation Positions
Table 5-63 lists the installation positions of the signal cable for the smoke sensor.
Table 5-63 Installation positions of the cable for the smoke sensor
Issue 01 (2007-09-10)
Signal Cable
Common Connector
5-79
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Functions
The signal cable for the water sensor connects the water sensor and the NPMI. It transmits the
water information collected by the water sensor to the NPMI.
Appearance
Figure 5-35 shows the signal cable for the water sensor.
Figure 5-35 Signal cable for the water sensor
2
1
A
View A
1
2
3
4
Pin Assignment
None.
Installation Positions
Table 5-64 lists the installation positions of the cable for the water sensor.
Table 5-64 Installation positions of the cable for the water sensor
Signal Cable
Common Connector
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Function
The RF signal cables are classified into RF RX signal cable and RF TX signal cable.
l
The RF RX signal cable connects the DDPU/DFCU/DFCB with the DTRU. This cable is
used to transmit UL signals.
The RF TX signal cable connects the DDPU/DFCU/DFCB with the DTRU. This cable is
used to transmits DL signals.
Structure
Figure 5-36 shows the structure of the RF RX signal cable and the RF TX signal cable.
Figure 5-36 Structure of the RF RX signal cable and the RF TX signal cable
Pin Description
None
Installation Positions
Table 5-65 describes the installation positions of the RF signal cables.
Table 5-65 Installation positions of the RF signal cables
Issue 01 (2007-09-10)
Cable
One End
Other End
RF TX signal cable
5-81
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Cable
One End
Other End
RF RX signal cable
NOTE
In inter-cabinet cell configuration, the RF RX cables should be connected between two cabinets. The
BTS3012 cabinet uses two 2.8 m long RF RX cables to set up the connection between the two cabinets.
The RF RX cable use SMA coaxial connectors at both ends.
Functions
The RF jumper connects the ANT port on the DDPU or DFCU and the feeder. The RF jumper
is used for the signal exchange between the BTS and the antenna system.
Appearance
One end of the 1/4-inch jumper is a DIN male connector and the other end is a DIN female
connector. Both ends of the 1/2-inch jumper are DIN male connectors.
Figure 5-37 shows the 1/4-inch RF jumper.
Figure 5-37 1/4-inch RF jumper
2
Pin Assignment
None.
5-82
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Installation Positions
Table 5-66 lists the installation positions of the RF jumpers.
Table 5-66 Installation positions of the RF jumpers
Cable
1/4-inch RF
jumper
1/2-inch RF
jumper on the
cabinet side
Function
The cables for the built-in battery are the GND cable, -48 V power cable, cable between the
wiring copper bar and the battery, cable between batteries, and signal cable for the temperature
sensor of the built-in battery.
l
The cable between the wiring copper bar and the battery and the cable between batteries
connect each battery in serial to form the built-in battery power supply system.
The signal cable for the temperature sensor of the built-in battery connects the built-in
battery and the NPMI. It transmits the temperature information collected by the temperature
sensor to the NPMI.
Appearance
The GND cable is red in color with the cross-sectional area of 25 mm2, as shown in Figure
5-39.
Issue 01 (2007-09-10)
5-83
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
3
W
The 48 V power cable is black in color with the cross-sectional area of 25 mm2, as shown in
Figure 5-40.
Figure 5-40 48 V power cable for the battery
2
3
W
The cable between the copper wiring bar and the battery is black in color with the cross-sectional
area of 16 mm2. It connects the battery and the copper wiring bar on the left inside the 50 AH
battery cabin.
The cable between batteries is black in color with the sectional area of 16 mm2.
Figure 5-41 shows the signal cable for the temperature sensor of the built-in battery.
Figure 5-41 Signal cable for the temperature sensor of the built-in battery
1
2
(1) OT terminal
Pin Description
None
Installation Positions
Table 5-67 shows the installation positions of the signal cables for the built-in battery.
5-84
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Table 5-67 Installation positions of the cables for the built-in battery
Cable Name
One End
GND cable
48 V power cable
Cable between
batteries
5.8.1 Signal cable of the external environment alarm box in the BTS
This part describes the function, structure, pin assignment, and installation positions of the signal
cable of the external environment alarm box in the BTS.
Issue 01 (2007-09-10)
5-85
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Function
The signal cable of the external environment alarm box is used to transmit the alarm signals to
the BTS. This helps the BTS take actions to clear the relevant alarms.
Appearance
Figure 5-42 shows the structure of the signal cable of the external environment alarm box.
Figure 5-42 Structure of the signal cable of the external environment alarm box
View B
Pos.1
View A
Pos.1
A
B
W
Pos.9
X1
X2
Pos.9
Pin Description
Table 5-68 describes the pin assignment for the signal cable of the external environment alarm
box.
Table 5-68 Pin assignment for the signal cable of the external environment alarm box
Pin at the X1 End
Wire Type
Remarks
X1.3
X2.2
Twisted pair
WARNING_T+
X1.7
X2.6
X1.2
X2.3
X1.6
X2.7
WARNING_TTwisted pair
WARNING_R+
WARNING_R-
Installation Positions
Table 5-69 shows the installation positions of the signal cable for the external environment alarm
box.
Table 5-69 Installation positions of the signal cable for the external environment alarm box
5-86
BTS Type
BTS3012
BTS3012AE
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
BTS Type
BTS3006C
BTS3002E
Functions
The power cables between the IBBS and the BTS3012AE introduce the power from the IBBS
battery cabinet to the BTS3012AE cabinet.
Appearance
There are two power cables between the IBBS and the BTS3012AE:
l
Figure 5-43 shows the power cables between the IBBS and the BTS3012AE.
Figure 5-43 Power cables between the IBBS and the BTS3012AE
Pin Assignment
None.
Installation Positions
Table 5-70 lists the installation positions of the power cables between the IBBS and the
BTS3012AE.
Issue 01 (2007-09-10)
5-87
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Table 5-70 Installation positions of the power cable between the IBBS and the BTS3012AE
Cable
GND cable
Connects to the
positive lead of the
wiring copper bar for
the external battery
cabinet
48 V cable
Connects to the
negative lead of the
wiring copper bar for
the external battery
cabinet
Functions
The equipotential cable between the IBBS and the BTS3012AE maintains the equal potential
between the IBBS and the BTS3012AE cabinet.
Appearance
The equipotential cable is green and yellow in color with a cross-sectional area of 25 mm2. Both
ends of the cable are OT terminals. Figure 5-44 shows the equipotential cable.
Figure 5-44 Equipotential cable between the IBBS and the BTS3012AE
Pin Assignment
None.
Installation Positions
Table 5-71 lists the installation positions of the equipotential cable between the IBBS and the
BTS3012AE.
5-88
Issue 01 (2007-09-10)
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Table 5-71 Installation positions of the equipotential cable between the IBBS and the
BTS3012AE
Cable
Equipotential cable
between the IBBS and the
BTS3012AE
Connects to the
protection grounding
bar at the bottom of the
BTS3012AE cabinet
5.8.4 Cable for the Door Control Sensor and Temperature Sensor
The cable for the door control sensor and temperature sensor reports the door control alarm
signals and the temperature alarm signals of the IBBS battery cabinet to the BTS3012AE.
Functions
The cable for the door control sensor and temperature sensor reports the door control alarm
signals and the temperature alarm signals of the IBBS battery cabinet to the BTS3012AE.
Appearance
Figure 5-45 shows the cable for the door control sensor and temperature sensor.
Figure 5-45 Cable for the door control sensor and temperature sensor
1
3
(1) Two bare wires (white and green) (2) Common 2-pin connector (3) Four bare wires (white, green, red, and
black)
Pin Assignment
None.
Installation Positions
Table 5-72 lists the installation positions of the cable for the door control sensor and temperature
sensor.
Issue 01 (2007-09-10)
5-89
BTS3012AE
Hardware Description(for FFU)
5 BTS3012AE Cables
Table 5-72 Installation positions of the cable for the door control sensor and temperature sensor
Cable
One End
5-90
Issue 01 (2007-09-10)