Professional Documents
Culture Documents
BACKGROUND
The basic concept used behind the operation is PASCALs LAW. This law states
that when a pressure is applied at one point of a fluid contained in a constrained
volume, then the pressure due to that force is equally transmitted to all the points
of the fluid, which are acted upon by the same pressure.
Using the same principle, we applied pressure to fluid in syringe which is
transmitted to other end of tube which is connected to a syringe. This
motion of the syringe is used to move the links or parts of the mechanism
which are attached to respective syringes
This hydraulic arm is designed to be a pick and place robot. A hydraulic arm is
powered by fluid under pressure. Hydraulic power is widely used for robots,
especially in situations where lots of power is needed.
The extensive use of hydraulics is to transmit power due to the fact that properly
constructed fluid power systems possess a
number
of
favourable
characteristics. They eliminate the need for complicated systems of gears, cams,
and levers.
Hydraulic robots use pressurized oil or water as the main working power.
HYDRAULIC ARM
Page 2
PROBLEM FORMULATION
With the advancement in technology there is something new coming out every now
and then, in this process of adapting to new technologies basic simpler
technologies are left out.
Advanced technology requires a lot on technological and monetary help.
The term basic/simpler means that even a tedious or intricate job can be with real
ease only if an individual sticks to the basics.
So, in this study we create a hydraulic robotic arm by reducing its cost and by
using simpler materials which are easily available.
OBJECTIVES
Some of the objectives of this study are mentioned below:
Eliminate the use of complicated gears, cams and levers.
Fluid is not subjected to breakage as compared to mechanical
parts.
Large power can be controlled by a small orifice (Syringe).
Fluids provide wide range of motion ( Rotary and Longitudinal)
HYDRAULIC ARM
Page 3
CHAPTER 1
Introduction to fluid power
Fluid power is a term which was created to include the generation,
control, and application of smooth, effective power of pumped or compressed
fluids (either liquids or gases) when this power is used to provide force and
motion to mechanisms. This force and motion maybe in the form of pushing,
pulling, rotating, regulating, or driving.
Fluid power includes hydraulics, which involves liquids, and pneumatics, which
involves gases. Liquids and gases are similar in many respects. The differences are
pointed out in the appropriate areas of this manual. This manual presents many of
the fundamental concepts in the fields of hydraulics and pneumatics. It is
intended as a basic reference for all
personnel of the Navy whose duties
and responsibilities require them to have a knowledge of the fundamentals of
fluid power.
Consequently, emphasis is placed primarily on the theory of operation of typical
fluid power systems and components that have applications in naval equipment.
Many applications of fluid power are presented in this manual to illustrate the
functions and operation of different systems and components. However,
these are only representative of the many applications of fluid power in naval
equipment. Individual training manuals for each rate provide information
concerning the application of fluid power to specific equipment for which
the rating is responsible.
1.1 History
The word hydraulics is based on the Greek word for water, and originally covered
the study of the physical behaviour of water at rest and in motion. Use has
broadened its meaning to include the behaviour of all liquids, although it is
primarily concerned with the motion of liquids. Hydraulics includes the
HYDRAULIC ARM
Page 4
manner in which liquids act in tanks and pipes, deals with their properties,
and explores ways to take advantage of these properties.
The time passed and the science of hydraulics kept on developing as more and
more efficient ways of converting hydraulic energy into useful work were
discovered.
The subject of hydraulics which dealt with the physical behaviour of water at rest
or in motion remained a part of civil engineering for a long time. However, after
the invention of James Watt's "steam engine", there arose the need for efficient
transmission of power, from the point of generation to the point of use.
Step by step many types of mechanical devices such as the line shaft, gearing
systems, pulleys and chains were discovered.
Therefore it was thought the concept of transmitting power through fluids under
pressure.
This indeed was a new field of hydraulics embracing different subjects such as
power transmission and control of mechanical motion, while also dealing with the
characteristics of fluids under pressure.
To distinguish this branch of hydraulics from water hydraulics, a new name called
"Industrial hydraulics" or more commonly, "oil hydraulics" was invented. The
significance behind choosing this name lies in the fact that this field of hydraulics
employs oil as a medium of power transmission. Water which is considered to be
practically incompressible is still used in present-day hydro technology.
The term water hydraulics has since been coined for this area of engineering.
Because of their superior qualities such as resistance to corrosion as well as their
sliding and lubricating capacity, oils which are generally mineral-based are the
preferred medium for transmission of hydraulic power.
HYDRAULIC ARM
Page 5
Fig.1
Fig. 2
HYDRAULIC ARM
Page 6
Fig. 3
The above figure shows pick and place robotic arm by hydraulic control. Its
working steps as under below:
Compressed fluid comes from the syringe.
By using syringes and pipes we control the flow of fluid and the working of
different arms.
By using low RPM motor the column rotates to object.
By gaining fluid power in syringe which is placed in arm opens jaws by
using hinge attachment.
Arm become down to object by gaining fluid in syringe.
Object comes between two jaws.
Arm rise up by when main syringe is pulled back by creating suction in the
syringe placed near the hinge attachment.
Whole assemblies rotate by low RPM motor at right place.
Arm become down to place object at right place by using above processes
HYDRAULIC ARM
Page 7
This can be stated as follows: the height of a column of water 1 foot high,
having a cross-sectional area of 1 square inch, is 0.433 pound. If the depth
of the column is tripled, the height of the column will be 3 x 0.433, or
1.299pounds, and the pressure at the bottom will be1.299 lb/in2 (psi), since
pressure equals the force divided by the area. Thus, the pressure at any depth
HYDRAULIC ARM
Page 8
HYDRAULIC ARM
Page 9
HYDRAULIC ARM
Page 10
Anything else things like the recycling bin, wood, metal, plastic, broken
toys, etc.
CHAPTER 2
Forces in liquids
The study of liquids is divided into two main parts:
liquids at rest (hydrostatics)
liquids in motion (hydraulics)
The effects of liquids at rest can often be expressed by simple formulas.
The effects of liquids in motion are more difficult to express due to
frictional and other factors whose actions cannot be expressed by simple
mathematics. Liquids have a definite volume but take the shape of their containing
vessel. There are two additional characteristics I must explore prior to
proceeding. Liquids are almost incompressible.
For example, if a pressure of 100 pounds per square inch (psi) is applied to a
given volume of water that is at atmospheric pressure, the volume will decrease
HYDRAULIC ARM
Page 11
HYDRAULIC ARM
Page 12
P=
F
A
The figure below illustrates a memory device for recalling the different variations
of this formula. Any letter in the triangle may be expressed as the product or
quotient of the other two, depending on its position within the triangle.
For example, to find area, consider the letter A as being set off to itself, followed
by an equal sign. Now look at the other two letters. The letter F is above the letter
P; therefore,
Fig. 6
NOTE: Sometimes the area may not be expressed in square units. If the surface is
rectangular, you can determine its area by multiplying its length (say, in
inches) by its width (also in inches). The majority of areas you will consider in
these calculations are circular in shape. Either the radius or the diameter may be
given, but you must know the radius in inches to find the area. The radius is onehalf the diameter. To determine the area, use the formula for finding the area of a
circle.
This is written
A =where A is the area
A= r 2 , is 3.1416 (3.14 or 3 1/7 for most calculations),
HYDRAULIC ARM
Page 13
,
Where:
HYDRAULIC ARM
Page 14
For water and other liquids, this integral can be simplified significantly for many
practical applications, based on the following two assumptions: Since many liquids
can be considered incompressible, a reasonably good estimation can be made from
assuming a constant density throughout the liquid. (The same assumption cannot
be made within a gaseous environment.) Also, since the height h of the fluid
column between z and z0 is often reasonably small compared to the radius of the
Earth, one can neglect the variation of g. Under these circumstances, the integral
boils down to the simple formula:
Where h is the height z z0 of the liquid column between the test volume and the
zero reference point of the pressure. Note that this reference point should lie at or
below the surface of the liquid. Otherwise, one has to split the integral into two (or
more) terms with the constant liquid and (z')above. For example, the absolute
pressure compared to vacuum is:
Hydrostatics is about the pressures exerted by a fluid at rest. Any fluid is meant,
not just water. It is usually relegated to an early chapter in Fluid Mechanics texts,
since its results are widely used in that study. The study yields many useful results
of its own, however, such as forces on dams, buoyancy and hydraulic actuation,
and is well worth studying for such practical reasons. It is an excellent example of
deductive mathematical physics, one that can be understood easily and completely
from a very few fundamentals, and in which the predictions agree closely with
experiment. There are few better illustrations of the use of the integral calculus, as
well as the principles of ordinary statics, available to the student. A great deal can
be done with only elementary mathematics. Properly adapted, the material can be
HYDRAULIC ARM
Page 15
used from the earliest introduction of school science, giving an excellent example
of a quantitative science with many possibilities for hands-on experiences.
The definition of a fluid deserves careful consideration. Although time is not a
factor in hydrostatics, it enters in the approach to hydrostatic equilibrium. It is
usually stated that a fluid is a substance that cannot resist a shearing stress, so that
pressures are normal to confining surfaces. Geology has now shown us clearly that
there are substances which can resist shearing forces over short time intervals, and
appear to be typical solids, but which flow like liquids over long time intervals.
Such materials include wax and pitch, ice, and even rock. A ball of pitch, which
can be shattered by a hammer, will spread out and flow in months. Ice, a typical
solid, will flow in a period of years, as shown in glaciers, and rock will flow over
hundreds of years, as in convection in the mantle of the earth. Shear earthquake
waves, with periods of seconds, propagate deep in the earth, though the rock there
can flow like a liquid when considered over centuries. The rate of shearing may not
be strictly proportional to the stress, but exists even with low stress. Viscosity may
be the physical property that varies over the largest numerical range, competing
with electrical resistivity.
A study of hydrostatics can also include capillarity, the ideal gas laws, the velocity
of sound, and hygrometry. These interesting applications will not be discussed in
this article. At a beginning level, it may also be interesting to study the volumes
and areas of certain shapes, or at a more advanced level, the forces exerted by
heavy liquids on their containers. Hydrostatics is a very concrete science that
avoids esoteric concepts and advanced mathematics. It is also much easier to
demonstrate than Newtonian mechanics.
HYDRAULIC ARM
Page 16
2.3.2 Pressure
By a fluid, we have a material in mind like water or air, two very common and
important fluids. Water is incompressible, while air is very compressible, but both
are fluids. Water has a definite volume; air does not. Water and air have low
viscosity; that is, layers of them slide very easily on one another, and they quickly
assume their permanent shapes when disturbed by rapid flows. Other fluids, such
as molasses, may have high viscosity and take a long time to come to equilibrium,
but they are no less fluids. The coefficient of viscosity is the ratio of the shearing
force to the velocity gradient. Hydrostatics deals with permanent, time-independent
states of fluids, so viscosity does not appear, except as discussed in the
Introduction.
A fluid, therefore, is a substance that cannot exert any permanent forces tangential
to a boundary. Any force that it exerts on a boundary must be normal to the
boundary. Such a force is proportional to the area on which it is exerted, and is
called a pressure. We can imagine any surface in a fluid as dividing the fluid into
parts pressing on each other, as if it were a thin material membrane, and so think of
the pressure at any point in the fluid, not just at the boundaries. In order for any
small element of the fluid to be in equilibrium, the pressure must be the same in all
directions (or the element would move in the direction of least pressure), and if no
other forces are acting on the body of the fluid, the pressure must be the same at all
neighbouring points. Therefore, in this case the pressure will be the same
throughout the fluid, and the same in any direction at a point (Pascal's Principle).
Pressure is expressed in units of force per unit area such as dyne/cm 2,
N/cm2 (Pascal), pounds/in2 (psi) or pounds/ft2 (psf). The axiom that if a certain
volume of fluid were somehow made solid, the equilibrium of forces would not be
disturbed is useful in reasoning about forces in fluids.
HYDRAULIC ARM
Page 17
On earth, fluids are also subject to the force of gravity, which acts vertically
downward, and has a magnitude = g per unit volume, where g is the acceleration
of gravity, approximately 981 cm/s2 or 32.15 ft/s2, is the density, the mass per
unit volume, expressed in g/cm3, kg/m3, or slug/ft3, and is the specific weight,
measured in lb/in3, or lb/ft3 (pcf). Gravitation is an example of a body force that
disturbs the equality of pressure in a fluid.
The presence of the gravitational body force causes the pressure to increase with
depth, according to the equation dp = g dh, in order to support the water above.
We call this relation the barometric equation, for when this equation is integrated,
we find the variation of pressure with height or depth. If the fluid is
incompressible, the equation can be integrated at once, and the pressure as a
function of depth h is p = gh + p0. The density of water is about 1 g/cm3, or its
specific weight is 62.4 pcf. We may ask what depth of water gives the normal sealevel atmospheric pressure of 14.7 psi, or 2117 psf. This is simply 2117 / 62.4 =
33.9 ft of water. This is the maximum height to which water can be raised by a
suction pump, or, more correctly, can be supported by atmospheric pressure.
Professor James Thomson illustrated the equality of pressure by a "curtain-ring"
analogy shown in the diagram. A section of the toroid was identified, imagined to
be solidified, and its equilibrium was analyzed.
Fig. 7
HYDRAULIC ARM
Page 18
The forces exerted on the curved surfaces have no component along the normal to
a plane section, so the pressures at any two points of a plane must be equal, since
the fluid represented by the curtain ring was in equilibrium. The right-hand part of
the diagram illustrates the equality of pressures in orthogonal directions. This can
be extended to any direction whatever, so Pascal's Principle is established. This
demonstration is similar to the usual one using a triangular prism and considering
the forces on the end and lateral faces separately.
When gravity acts, the liquid assumes a free surface perpendicular to gravity,
which can be proved by Thomson's method. A straight cylinder of unit crosssectional area (assumed only for ease in the arithmetic) can be used to find the
increase of pressure with depth.
Fig. 8
Indeed, we see that p2 = p1 + gh. The upper surface of the cylinder can be placed
at the free surface if desired. The pressure is now the same in any direction at a
point, but is greater at points that lie deeper. From this same figure, it is easy to
prove Archimedes's Principle that the buoyant force is equal to the weight of the
displaced fluid, and passes through the centre of mass of this displaced fluid.
Ingenious geometric arguments can be used to substitute for easier, but less
transparent arguments using calculus. For example, the force on acting on one side
of an inclined plane surface whose projection is AB can be found as in the diagram
HYDRAULIC ARM
Page 19
free surface.
Fig. 9
The line AC' perpendicular to the plane is made equal to the depth AC of point A,
and line BD' is similarly drawn equal to BD. The line OD' also passes through C',
by proportionality of triangles OAC' and OAD'. Therefore, the thrust F on the
plane is the weight of a prism of fluid of cross-section AC'D'B, passing through its
centroid normal to plane AB. Note that the thrust is equal to the density times the
area times the depth of the centre of the area, but its line of action does not pass
through the centre, but below it, at the centre of thrust. The same result can be
obtained with calculus by summing the pressures and the moments, of course.
pump
applied to the upper end. Before we start the pump, the water levels outside and
inside the pipe are equal, and the pressures on the surfaces are also equal, and
equal to the atmospheric pressure. Now start the pump.
HYDRAULIC ARM
Page 20
Fig. 10
When it has sucked all the air out above the water, the pressure on the surface of
the water inside the pipe is zero, and the pressure at the level of the water on the
outside of the pipe is still the atmospheric pressure. Of course, there is the vapour
pressure of the water to worry about if you want to be precise, but we neglect this
complication in making our point. We require a column of water 33.9 ft high inside
the pipe, with a vacuum above it, to balance the atmospheric pressure. Now do the
same thing with liquid mercury, whose density at 0 C is 13.5951 times that of
water. The height of the column is 2.494 ft, 29.92 in, or 760.0 mm. This definition
of the standard atmospheric pressure was established by Regnault in the mid-19th
century. In Britain, 30 in Hg (inches of mercury) had been used previously.
As a practical matter, it is convenient to measure pressure differences by measuring
the height of liquid columns, a practice known as manometry. The barometer is a
familiar example of this, and atmospheric pressures are traditionally given in terms
of the length of a mercury column. To make a barometer, the barometric tube,
closed at one end, is filled with mercury and then inverted and placed in a mercury
reservoir. Corrections must be made for temperature, because the density of
mercury depends on the temperature, and the brass scale expands, for capillarity if
the tube is less than about 1 cm in diameter, and even slightly for altitude, since the
value of g changes with altitude. The vapour pressure of mercury is only 0.001201
mmHg at 20C, so a correction from this source is negligible. For the usual case of
HYDRAULIC ARM
Page 21
Page 22
availability of ft-lb per lb. Water with a pressure head of 10 ft can furnish the same
energy as an equal amount of water raised by 10 ft. Water flowing in a pipe is
subject to head loss because of friction.
Take a jar and a basin of water. Fill the jar with water and invert it under the water
in the basin. Now raise the jar as far as you can without allowing its mouth to come
above the water surface. It is always a little surprising to see that the jar does not
empty itself, but the water remains with no visible means of support. By blowing
through a straw, one can put air into the jar, and as much water leaves as air enters.
In fact, this is a famous method of collecting insoluble gases in the chemical
laboratory, or for supplying hummingbird feeders. It is good to remind oneself of
exactly the balance of forces involved.
Another application of pressure is the siphon. The name is Greek for the tube that
was used for drawing wine from a cask. This is a tube filled with fluid connecting
two containers of fluid, normally rising higher than the water levels in the two
containers, at least to pass over their rims.
Fig. 11
In the diagram, the two water levels are the same, so there will be no flow. When a
siphon goes below the free water levels, it is called an inverted siphon. If the levels
HYDRAULIC ARM
Page 23
in the two basins are not equal, fluid flows from the basin with the higher level into
the one with the lower level, until the levels are equal.
A siphon can be made by filling the tube, closing the ends, and then putting the
ends under the surface on both sides. Alternatively, the tube can be placed in one
fluid and filled by sucking on it. When it is full, the other end is put in place. The
analysis of the siphon is easy, and should be obvious. The pressure rises or falls as
described by the barometric equation through the siphon tube. There is obviously a
maximum height for the siphon which is the same as the limit of the suction pump,
about 34 feet. Inverted siphons (which are really not siphons at all) are sometimes
used in pipelines to cross valleys. Differences in elevation are usually too great to
use regular siphons to cross hills, so the fluids must be pressurized by pumps so the
pressure does not fall to zero at the crests. The Quabbin Aqueduct, which supplies
water to Boston, includes pumped siphons.
As the level in the supply container falls, the pressure difference decreases. In
some cases, one would like a source that would provide a constant pressure at the
outlet of the siphon.
Fig. 12
An ingenious way to arrive at this is shown in the figure, Mariotte's Bottle. The
plug must seal the air space at the top very well. A partial vacuum is created in the
HYDRAULIC ARM
Page 24
air space by the fall of the water level exactly equal to the pressure difference
between the surface and the end of the open tube connecting to the atmosphere.
The pressure at this point is, therefore, maintained at atmospheric while water is
delivered. The head available at the nozzle as shown is equal to h. This would
make a good experiment to verify the relation V = (2gh) since h and the
horizontal distance reached by the jet for a given fall can both be measured easily,
or the discharge from an orifice.
The term "siphon" is often used in a different sense. In biology, a siphon is simply
a tubular structure. A thermal siphon is a means to circulate a liquid by convection.
A soda siphon is a source of carbonated water, while siphon coffee (or vacuum
coffee) is made in an apparatus where the steam from boiling water pushes hot
water up above the coffee and filter, and then the vacuum causes the water to
descend again when the heat is removed (invented by Lff in 1830). None of these
arrangements is actually a siphon in the physicist's sense. The siphon tube used in
irrigation, and perhaps Thomson's siphon recorder of 1858, do use the siphon
principle. The occasional spelling "syphon" is not supported by the Greek source.
In some cases, especially in plumbing, siphon action is not desired, especially
when it may allow dirty water to mix with clean. In these cases, vacuum
breakers may be used at high points to prevent this. Siphons work because of
atmospheric pressure, and would not operate in a vacuum. In the case of water,
pressure reduction would eventually reach the vapour pressure and the water would
boil. Mercury, which has a very low vapour pressure, would simply separate
leaving a Torricellian vacuum. The siphon would be re-established if the pressure
is restored. A liquid column is unstable under a negative pressure.
HYDRAULIC ARM
Page 25
atmosphere,
vacui as
supposed.
Aristotle
had
not
by horror
Fig. 13
Torricelli's early death was a blow to science, but his ideas were furthered by
Blaise Pascal (1623-1662). Pascal had a barometer carried up the 1465 m high Puy
de Dme, an extinct volcano in the Auvergne just west of his home of ClermontFerrand in 1648 by Prier, his brother-in-law. Pascal's experimentum crucis is one
of the triumphs of early modern science. The Puy de Dme is not the highest peak
in the Massif Central--the Puy de Sancy, at 1866 m is, but it was the closest.
Clermont is now the centre of the French pneumatics industry.
The remarkable Otto von Guericke (1602-1686), Burgomeister of Magdeburg,
Saxony, took up the cause, making the first vacuum pump, which he used in vivid
demonstrations of the pressure of the atmosphere to the Imperial Diet at
Regensburg in 1654. Famously, he evacuated a sphere consisting of two wellfitting hemispheres about a foot in diameter, and showed that 16 horses, 8 on each
side, could not pull them apart. An original vacuum pump and hemispheres from
1663 are shown at the right (photo edited from the Deutsches Museum; see link
below). He also showed that air had weight, and how much force it did require to
HYDRAULIC ARM
Page 26
shown,
with
the
upper
Fig. 14
As the large container is filled with water, pressure on the free surfaces of the
mercury in the beakers pushes mercury into the tubes. When the state shown is
reached, the beakers are connected by a mercury column, and the siphon starts,
emptying the upper beaker and filling the lower. The mercury has been open to the
atmosphere all this time, so if there were any horror vacui, it could have flowed in
at will to soothe itself.
The mm of mercury is sometimes called a torr after Torricelli, and Pascal also has
been honoured by a unit of pressure, a newton per square metre or 10 dyne/cm 2. A
cubic centimetre of air weighs 1.293 mg under standard conditions, and a cubic
HYDRAULIC ARM
Page 27
ln(p/p0)
-Mgh/RT,
or
finally
p0exp(-Mgh/RT).
In
Page 28
level the atmosphere warms again to near its value at the surface. Of course, there
are variations from the average values. When the temperature profile with height is
known, we can find the pressure by numerical integration quite easily.
The atmospheric pressure is of great importance in meteorology, since it
determines the winds, which generally move at right angles to the direction of most
rapid change of pressure, that is, along the isobars, which are contours of constant
pressure. Certain typical weather patterns are associated with relatively high and
relatively low pressures, and how they vary with time. The barometric pressure
may be given in popular weather forecasts, though few people know what to do
with it. If you live at a high altitude, your local weather reporter may report the
pressure to be, say, 29.2 inches, but if you have a real barometer, you may well find
that it is closer to 25 inches. At an elevation of 1500 m (near Denver), the
atmospheric pressure is about 635 mm, and water boils at 95 C. In fact, altitude is
quite a problem in meteorology, since pressures must be measured at a common
level to be meaningful.
The barometric pressures quoted in the news are reduced to sea level by standard
formulas, that amount to assuming that there is a column of air from your feet to
sea level with a certain temperature distribution, and adding the weight of this
column to the actual barometric pressure. This is only an arbitrary 'fix' and leads to
some strange conclusions, such as the permanent winter highs above high plateaus
that are really imaginary.
2.5 Multiplication of forces
Consider the situation in figure , where the input piston is much smaller than
the output piston. Assume that the area of the input piston is 2square inches. With
a resistant force on the output piston a downward force of 20 pounds acting on the
HYDRAULIC ARM
Page 29
20
2
much smaller than the force applied in figures 2-9 and 2-10, the pressure is the
same. This is because the force is applied to a smaller area.
This pressure of 10 psi acts on all parts of the fluid container, including the bottom
of the output piston. The upward force on the output piston is 200 pounds (10
pounds of pressure on each square inch). In this case, the original force has been
multiplied tenfold while using the same pressure in the fluid as before. In any
system with these dimensions, the ratio of output force to input force is always ten
to one, regardless of the applied force. For example, if the applied force of the
input piston is 50 pounds, the pressure in the system will be 25 psi. This will
support a resistant force of 500 pounds on the output piston.
HYDRAULIC ARM
Page 30
The system works the same in reverse. If I change the applied force and place a
200-pound force on the output piston (fig.), making it the input piston, the
output force on the input piston will be one-tenth the input force, or
20pounds. Therefore, if two pistons are used in a fluid power system, the
force acting on each piston is directly proportional to its area, and the
magnitude of each force is the product of the pressure and the area of each
piston.
CHAPTER 3
Hydraulic fluids
During the design of equipment that requires fluid power, many factors are
considered in selecting the type of system to be usedhydraulic, pneumatic, or a
combination of the two. Some of the factors are required speed and accuracy of
operation, surrounding atmospheric conditions, economic conditions,
availability of replacement fluid, required pressure level, operating temperature
HYDRAULIC ARM
Page 31
3.1 Properties
If fluidity (the physical property of a substance that enables it to flow) and
incompressibility Ire the only properties required, any liquid not too thick
might be used in a hydraulic system. However, a satisfactory liquid for a
particular system must possess a number of other properties. The most important
properties and some characteristics are discussed in the following paragraphs.
3.1.1 Viscosity
HYDRAULIC ARM
Page 32
HYDRAULIC ARM
Page 33
flow through the capillary. This time is multiplied by the temperature constant of
the viscometer in use to provide the viscosity, expressed in centistokes.
The following formulas may be used to convert centistokes (cSt units) to
approximate Say bolt universal seconds (SUS units).
For SUS values between 32 and 100
Page 34
wide temperature range. Ideal oil for most purposes is one that
maintains a constant viscosity throughout temperature changes. The
importance of the viscosity index can be shown easily by considering
automotive lubricants. Oil having a high viscosity index resists
excessive thickening when the engine is cold and, consequently,
promotes rapid starting and prompt circulation; it resists excessive
thinning when the motor is hot and thus provides full lubrication and
prevents excessive oil consumption.
Another example of the importance of the viscosity index is the need for
a high viscosity index hydraulic oil for military aircraft, since hydraulic
control systems may be exposed to temperatures ranging from below
65F at high altitudes to over 100F on the ground. For the proper
operation of the hydraulic control system, the hydraulic fluid must have a
sufficiently high viscosity index to perform its functions at the extreme
of the expected temperature range. Liquids with a high viscosity have a
greater resistance to heat than low viscosity liquids which have been
derived from the same smyce. The average hydraulic liquid has a
relatively low viscosity.
Fortunately, there is a wide choice of liquids available for use in the
viscosity range required of hydraulic liquids. The viscosity index. Of
an oil may be determined if its viscosity at any two temperatures is
known. Tables, based on a large number of tests, are issued by the
American Society for Testing and Materials (ASTM). These tables
permit calculation of the viscosity index From known viscosities.
Page 35
the vessel with the leak to remains undetected. Recall from that under extreme
pressure a fluid may be compressed up to 7 percent of its original volume.
Highly compressible fluids produce sluggish system operation. This does not
present a serious problem in small, low-speed operations, but it must be considered
in the operating instructions.
3.1.3 Cleanliness
Cleanliness in hydraulic systems has received considerable attention recently.
Some hydraulic systems, such as aerospace hydraulic systems, are extremely
sensitive to contamination. Fluid cleanliness is of primary importance because
contaminants can cause component malfunction, prevent proper valve seating,
cause Air in components, and may increase the response time of servo valves.
Fluid contaminants are discussed later. The inside of a hydraulic system can only
be kept as clean as the fluid added to it. Initial fluid cleanliness can be achieved
by observing stringent cleanliness requirements ( or by filtering all fluid added
to the system).
3.2 Types of hydraulic fluids
There have been many liquids tested for use in hydraulic systems. Currently,
liquids being used include mineral oil, water, phosphate ester, water-based ethylene
glycol compounds, and silicone fluids. The three most common types of hydraulic
liquids are petroleum-based, synthetic fire-resistant, and water-based fire-resistant
PwSH
eny
bthd
erir
ofifia
-l ru
ruil
smac
nF
Bl
au
y
r t
ae
d
t
st
rr
i
si
e
e
ee
s
s
t
t
i
t
si
ed
ds
Fig. 18
3.2.1 Petroleum based fluids
The most common hydraulic fluids used in shipboard systems are the petroleumbased oils. These fluids contain additives to protect the fluid from oxidation
HYDRAULIC ARM
Page 36
Page 37
Function
Property
bulk
modulus)
Medium for power transfer
and control
Low volatility
Good
thermal
capacity
and
conductivity
Sealing Medium
Lubricant
HYDRAULIC ARM
Shear stability
Page 38
Demulsibility
Antiwear characteristics
Corrosion control
Proper
Pump efficiency
Special function
HYDRAULIC ARM
to
minimize
internal leakage
Fire resistance
Friction modifications
Radiation resistance
Low
Environmental impact
Functioning life
viscosity
toxicity
when
decomposed
Biodegradability
Material compatibility
Page 39
new
or
CHAPTER 4
Components used in the fabrication of this project
4.1 Hydraulic syringes
Syringes are essentially simple hydraulic systems, as they operate by moving a
liquid from one place to another. The difference is that a hydraulic system uses the
liquid to move another object, syringes just move the liquid. This means that
syringes are the most basic form of hydraulics.
A Hydraulic system is a power transmission system that uses the force of flowing
liquids to transmit power. It consists of two pistons and an oil-filled pipe
connecting them. A hydraulic arm is an arm that requires a hydraulic system in
order to operate. A hydraulic arm is often used for heavy, repetitive manufacturing
work. They handle tasks that are difficult or dangerous to human beings by
transporting objects from one place to another. A hydraulic arm works with or
without the use of a computer, which controls it by rotating individual step motors
connected to each joint.
HYDRAULIC ARM
Page 40
Fig. 19
4.1.1 Operation
Hydraulic syringe get their power from pressurized hydraulic fluid, which is
typically oil or water. The hydraulic syringe consists of a cylinder barrel, in which
a piston connected to a piston rod moves back and forth. The barrel is closed on
one end by the cylinder bottom (also called the cap) and the other end by the
cylinder head (also called the gland) where the piston rod comes out of the
cylinder. The piston has sliding rings and seals. The piston divides the inside of the
cylinder into two chambers, the bottom chamber (cap end) and the piston rod side
chamber (rod end / head end).
Flanges, trunnions, clevises, Lugs are common cylinder mounting options. The
piston rod also has mounting attachments to connect the cylinder to the object or
machine component that it is pushing / pulling.
The piston pushes the water in the other chamber back to the reservoir. If we
assume that the oil enters from cap end, during extension stroke, and the oil
pressure in the rod end / head end is approximately zero, the force F on the piston
rod equals the pressure P in the cylinder times the piston area A:
HYDRAULIC ARM
Page 41
During the retraction stroke, if oil is pumped into the head (or gland) at the rod end
and the oil from the cap end flows back to the reservoir without pressure, the fluid
pressure in the rod end is (Pull Force) / (piston area - piston rod area):
Where:
P is the fluid pressure,
Fp is the pulling force,
Ap is the piston face area
Ar is the rod cross-section area.
4.1.2 Single acting vs. double acting
Single acting cylinders are economical and the simplest design. Hydraulic fluid
enters through a port at one end of the cylinder, which then moves the piston to
extend the rod. An external force returns the piston to its normal position and
forces the hydraulic fluid back through the supply tubing to the fluid reservoir.
Double acting cylinders have a port at each end, supplied with hydraulic fluid for
both the retraction and extension of the piston. They are used where an external
force is not available to retract the piston or where high force is required in both
directions of travel.
A hydraulic cylinder should be used for pushing and pulling only. No bending
moments or side loads should be transmitted to the piston rod or the cylinder to
prevent rapid failure of the rod seals. For this reason, the ideal connection of an
hydraulic cylinder is a single clevis with a spherical ball bearing. This allows the
hydraulic actuator to move and allow for any misalignment between the actuator
and the load it is pushing.
In my project I have used Syringes working as hydraulic cylinders.
HYDRAULIC ARM
Page 42
Fig. 20
4.2 Fluid lines and fittings
The control and application of fluid power would be impossible without
suitable means of transferring the fluid between the reservoir, the power source,
and the points of application. Fluid lines are used to transfer the fluid, and
fittings are used to connect the lines to the power source and the points of
application.
4.2.1 Types of lines
Three types of lines is used in this system are pipe (rigid), tubing (semi
rigid) and hose (flexible).
There are number of factors are considered while selecting the line for particular
system. These factors include the type of fluid required in system pressure and the
location of the system.
For example, heavy pipe might be used for a large stationary fluid power system,
but comparatively height height tubing must be used in aircraft and missile
systems because height and space are critical factors. Flexible hose is required
in installations where units must be free to move relative to each
4.3 Pipes and tubing
There are three important dimensions of any tubular productoutside diameter
(OD), inside diameter (ID), and wall thickness. Sizes of pipe are listed by the
HYDRAULIC ARM
Page 43
nominal (or approximate) ID and the wall thickness. Sizes of tubing are
listed by the actual OD and the wall thickness.
4.3.1 Selection of pipes and tubing
The material, ID, and wall thickness are the three primary considerations in
the selection of lines for a particular fluid power system. The ID of a
line is important, since it determines how much fluid can pass through the line
in a given time period (rate of flow)without loss of power due to excessive
friction and heat. The velocity of a given flow is less through a large
opening than through a small opening. If the ID of the line is too small for the
amount of flow, excessive turbulence and friction heat cause unnecessary power
loss and overheated fluid.
4.3.2 Sizing of Pipes and Tubing
Pipes are available in three different heights: standard (STD), or Schedule 40;
extra strong(XS), or Schedule 80; and double extra strong(XXS). The
schedule numbers range from 10to 160 and cover 10 distinct sets of
wall thickness. Schedule 160 wall thickness is slightly thinner than the double
extra strong. As mentioned earlier, the size of pipes is determined by the nominal
(approximate) ID. For example, the ID for a 1/4-inch Schedule 40 pipe is 0.364
inch, and the ID for a 1/2-inch Schedule40 pipe is 0.622 inch. It is important to
note that the IDs of all pipes of the same nominal size are not equal. This is
because the OD remains constant and the wall thickness increases as the
schedule number increases.
For example, a nominal size 1-inchSchedule 40 pipe has a 1.049 ID. The same size
Schedule 80 pipe has a 0.957 ID, while Schedule.
HYDRAULIC ARM
Page 44
160 pipe has a 0.815 ID. In each case the OD is1.315 (table 5-1) and the wall
thicknesses
are
0.250(1.3150.815)
2
0.133(1.3151.049)
2
0.179(1.3159.957)
2
and
respectively.
4.3.3 Materials
The pipe and tubing used in fluid power systems are commonly made from steel,
copper, brass, aluminium, and stainless steel. Each of these metals has its own
distinct advantages or disadvantages in certain applications. Steel pipe and tubing
are relatively in expensive and are used in many hydraulic and pneumatic systems.
Steel is used because of its strength, suitability for bending and flanging, and
adaptability to high pressures and temperatures.
Its chief disadvantage is its comparatively low resistance to corrosion. Copper pipe
and tubing are sometimes used for fluid power lines. Copper has high resistance to
corrosion and is easily drawn or bent. However ,it is unsatisfactory for high
temperatures and has a tendency to harden and break due to stress and
vibration. Aluminium has many of the characteristics and qualities required for
fluid power lines. It has high resistance to corrosion and is easily drawn or bent. In
addition, it has the outstanding characteristic of height. Since height elimination
is a vital factor in the design of aircraft, aluminium alloy tubing is used in
the majority of aircraft fluid power systems. Stainless-steel tubing is used in
HYDRAULIC ARM
Page 45
certain areas of many aircraft fluid power systems. As a general rule, exposed lines
and lines subject to abrasion or intense heat are made of stainless steel.
Therefore in maintenance and repair of fluid power system lines, the basic
design requirements must be kept in mind. Two primary requirements are as
follows:
1. The lines must have the correct ID to provide the required volume and
velocity of flow with the least amount of turbulence during all demands
on the system.
2. The lines must be made of the proper material and have the wall
thickness to provide sufficient strength to both contain the fluid at the
required pressure and withstand the surges of pressure that may develop
in the system.
In my project I have used three sections of clear 1/8 I.D. Vinyl tubing of different
lengths.
75 cm (~29.5)
75 cm(~29.5)
110 cm (~43.5)
Fig. 21
HYDRAULIC ARM
Page 46
4.4 Grippers
Grippers are used to grasp and hold objects. The objects are generally work parts
that are to be moved by the hydraulic arm. These part handling applications include
machine loading and unloading, picking parts from a conveyor, and arranging parts
into a pallet.
Depending on the mechanism used for the purpose of gripping they can be
classified as:
1. Mechanical Grippers
2. Adhesive Grippers
3. Hooks, Scoops etc
4. Vacuum Cups
5. Magnetic Grippers
In this project I have used mechanical gripper which is discussed below:
HYDRAULIC ARM
Page 47
HYDRAULIC ARM
Page 48
Fig. 22CHAPTER 5
Manufacturing process
5.1 Parts of Hydraulic arm
5.1.1 syringes
Fig. 23 and 24
5.1.2 Aluminium Rod
Fig. 25
HYDRAULIC ARM
Page 49
5.1.3 Hinge
Fig. 26
Fig. 27
5.1.5 Pipes
HYDRAULIC ARM
Page 50
Fig. 28
Fig. 29
HYDRAULIC ARM
Page 51
Fig. 30
Fig. 31
HYDRAULIC ARM
Page 52
Fig. 32
Fig. 33
HYDRAULIC ARM
Page 53
Fig. 34
Fig. 35
HYDRAULIC ARM
Page 54
Fig. 36
Fig. 37
HYDRAULIC ARM
Page 55
CHAPTER 6
Working of Fabricated model
6.1 Degrees of freedom(D.O.F)
A degree of freedom is defined as the minimum number of independent
coordinates required for specifying the complete motion of a system. In this
hydraulic syringe arm, there are three types of motions that can be executed by the
arm.
So, there are three degrees of freedom for this system which are comprehended
below: The first degree of freedom accounts for the vertical or up and down motion
of the hydraulic arm. The second degree of freedom accounts for the angular or
side way movement of the hydraulic arm. The third degree of freedom accounts for
the opening and closing of the jaw.
6.2 Calculation of weight lifting capacity
The efficiency of a Hydraulic arm is determined by its capacity to lift the
maximum amounts of weights efficiently. I applied the simplest hit and trail
method to find out the maximum amount of weight that our hydraulic arm can lift.
Under this method I increased the amount of weights to be lifted from zero. Since
the levers and the arm are made up of aluminium, therefore they can withstand a
high value of pressure. But the major problem which is encountered is the fluid
HYDRAULIC ARM
Page 56
used and the cylinders used which are common syringes. It was observed that the
arm can lift weight up to 1 kg efficiently. But when the values of the weight to be
lifted are increased further, the rubber seal on the piston becomes ineffective to
hold the water and this results, leakage or spilling of the water over the seal. This
may be due to the less viscosity of the water and due to the less effectiveness of the
rubber seals.
6.3 Operation
In this arrangement, we have three pairs of syringes. Each pair is interconnected by
means of thick walled plastic pipes which are very flexible and elastic in nature.
The aim of this pairing is to facilitate the motion of fluid from one Syringe to the
other by means of the plastic tubes.
This means that if we will apply force on piston of one syringe, the pressure will be
transmitted through the fluid to the other syringe and the same force will be
obtained from the other piston.
Thus, in a pair, if one piston executes downward motion, the piston of other
syringe will execute an upward motion. One syringe of each pair is held firmly in a
frame and the other account for the specific motion of the arm.
For the implementation of the motion, the piston of each syringe held in the frame
is connected to different levers by means of connecting strips made up of iron.
Lever accounts for the vertical i.e up and movement of the hydraulic arm. When
the lever is pressed the pressure transmitted is such that the arm moves up. When
the lever is pulled back or lowered, the arm moves downwards.
Lever accounts for the motion of the jaw i.e. its opening and closing. When this
lever is pressed, the jaw opens and when this lever is pulled back, the jaw closes.
HYDRAULIC ARM
Page 57
CHAPTER 7
Analysis
7.1 Pressure and Force in Fluid Power Systems
Recall that, according to Pascals law, any force applied to a confined fluid
is transmitted in all directions throughout the fluid regardless of the shape of the
container. Consider the effect of this in the system shown in figure. If there is a
resistance on the output piston and the input piston is pushed downward, a pressure
is created through the fluid, which acts equally at right angles to surfaces in
all parts of the container. If force 1 is 100 pounds and the area of the input
piston is 10 square inches, then the pressure in the fluid is 10 psi
HYDRAULIC ARM
Page 58
Fig. 38
Figure Force transmitted through fluid
NOTE: Fluid pressure cannot be created without resistance to flow. In this
case, resistance is provided by the equipment to which the output piston is
attached. The force of resistance acts against the top of the output piston. The
pressure created in the system by the input piston pushes on the underside
of the output piston with a force of 10 pounds on each square inch. In this
case, the fluid column has a uniform cross section, so the area of the output
piston is the same as the area of the input piston, or 10 square
inches. Therefore, the upward force on the output piston is 100 pounds (10
psi x 10 sq. in.), the same as the force applied to the input piston. All that was
accomplished in this system was to transmit the 100-pound force around the bend.
However, this principle under-lies practically all mechanical applications of fluid
power. At this point you should note that since Pascals law is independent
of the shape of the container, it is not necessary that the tube connecting
the two pistons have the same cross-sectional area of the pistons. A connection
of any size, shape, or length will do, as long as an unobstructed passage is
provided. Therefore, the system shown in figure 2-10, with a relatively small, bent
pipe connecting two cylinders, will act exactly the same as the system shown in
Figure 2-9.
7.2 Additional Experiments
I have been working on building a simulator to demonstrate Pascals Principle of
fluids using syringes and plastic tubing.
HYDRAULIC ARM
Page 59
Pascals Principle states that when there is an increase in pressure at any point in a
confined fluid, there is an equal increase at every other point in the container.
What exactly does this mean in practice? For the simulator I used a large syringe
that has a piston cross section diameter of 34 mm and small syringe with cross
section diameter of 13 mm. Like other mechanical systems there is a mechanical
advantage where distance moved and force trade off. When the smaller piston is
pushed with a force, the force is distributed equally across the larger piston cross
section causing a greater net force. For the fluid to be spread across the larger cross
section more fluid volume must be moved from the smaller cylinder.
Fig. 39
For my first experiment I worked from the other direction and pushed the large
cylinder a short distance of 9 mm which extended the small cylinder a much longer
distance of around 60 mm until it could not move any farther. I calculated this also
which was off the first time but repeated trial proved that calculated and observed
were very close.
HYDRAULIC ARM
Page 60
Fig. 40 and 41
HYDRAULIC ARM
Page 61
CHAPTER 8
CAD DESIGN
8.1 Top View
Fig.42
8.2 Right Hand Side View
HYDRAULIC ARM
Page 62
Fig. 43
Fig. 44
HYDRAULIC ARM
Page 63
Fig. 45
CHAPTER 9
9.1 Future scope
Here are many different reasons for using a hydraulic arm but the central reason for
most applications is to eliminate a human operator. The most obvious reason is: To
save labour and reduce cost. Other classes of applications concern the product:
1. Areas where human is not suitable for handling products e.g.
semiconductor handling.
2. Product is bad for the human for example radioactive product. 3
3. Activities affecting human health: Repetitive strain syndrome. Working
with machinery that is dangerous for example presses, winders. Working
with materials which might be harmful in the short or long term.
4. Quality while the main reason for using a hydraulic arm is to save labour
the biggest impact a hydraulic has can be on quality.
5. Applications where quality will be improved are: gluing, spraying (glue or
paint), trimming and de-burring, testing and gauging. assembly laboratory
routines
9.1.1 FUTURE SCOPE OF NANOROBOTICSThe emerging revolutionary era Nanorobotics is concerned with Manipulation of
nanoscale objects by using micro or macro devices, and construction and
HYDRAULIC ARM
Page 64
programming of robots with overall dimensions at the nanoscale. Nano robots have
extremely small size approximately 10-9 of a meter. They are capable of treating
those parts which are so small that cannot be seen by the naked eyes. The various
fields of applications include- Nanorobots in dentistry- In tooth repair. Tooth
durability and appearance Nanomedicines Nanorobots in cancer detection and
treatment. Nanorobots in diagnosis and treatment of diabetes. Nanorobots in
surgery. Nanorobots in gene therapy.
9.1.4 MILITARY AND BOMB DIFFUSING: There are many aspects in military
where danger is at its extreme points. Since the soldiers are a valuable part of the
military, therefore instead of putting their lives in danger, the military is using the
robots. The most common use is taken in BOMB DIFFUSING.
9.1.5 EXPLORING THE SPACE: Neither we are not the sole creatures of this
universe and nor earth is the only planet. The universe extends beyond our
HYDRAULIC ARM
Page 65
expectations and limits. To explore the outer space robots are specially used. They
send to the outer planets to gather information about the existence of life on other
planets. AVGs i.e. automatically guided vehicles are specially used for this
purpose. An automated guided vehicle or automatic guided vehicle (AGV) is a
mobile robot that follows markers or wires in the floor, or uses vision or lasers.
They are most often used in industrial applications to move materials around a
manufacturing facility or a warehouse. Application of the automatic guided vehicle
has broadened during the late 20th century.
9.1.6 USE IN DAILY LIFE: There are many robots which are used in daily life to
assist the humans in various tasks such as: cooking Chopping vegetables, to move
stuff from one place to another. Washing Playing (toy robots) Care of old aged
persons Special care for disabled.
Limitations of my model
The first limitation is regarding the type of fluid used i.e. the water. Its viscosity is
low. Therefore is cannot offer a good seal at the piston. Water cannot withstand
high pressure. When higher pressure is applied, it leaks out of the piston. The
syringes which are used cannot provide a tight seal between the fluid and the
piston. The sideway angle of coverage is limited to approximately 170 degrees.
The maximum weight that can be lifted is about 1 kg. The arm lacks the fourth
degree of freedom corresponding to the movement about wrist.
APPLICATION
The siphon
The underlying principle of the hydraulic jack and hydraulic press
Force amplification in the braking system of most motor vehicles.
Used in artesian wells, water towers, and dams.
HYDRAULIC ARM
Page 66
CONCLUSION
My design uses extremely simple ideas and mechanisms to achieve a complex set
of actions and is intended to imitate the actions of the operators. However, these
hydraulic arms are expensive for small scale industries. If the major problem of
high initial cost is addressed, a hydraulic arm can be introduced in any industry to
bring in automation. The mechanical links and parts that have been fabricated are
extremely simple.
Hydraulic Arm will
HYDRAULIC ARM
Page 67
HYDRAULIC ARM
Page 68