Professional Documents
Culture Documents
htm
Lesson
160
Lesson Objective: In this lesson, we will learn about the Hole Feature.
HOLE USAGE
This is another widely underused feature that should be used more often. Many people use extruded
cuts or revolved cuts instead of holes, but many of the straight holes or even standard holes do not
need to be sketched, and that will save time (both in regeneration and in the users time).
There are two main types of holes:
Straight The profile is either a plain circle extruded to a certain depth, or you can sketch a
profile that creates a revolved cut.
Linear Hole lies on a plane or planar surface and is located from two references (similar
to a datum point on surface).
Radial (Cylindrical) Hole lies on the outside of a cylindrical surface, measured from a
reference that is perpendicular to the cylinders axis, and located about the axis by some angle
reference.
Radial (Axial) Hole lies on a plane or planar surface, but is located about an axis normal
to that surface. Dimensions are radius or diameter around axis, and an angle through the axis.
Coaxial Hole lies along a datum axis and starts from a specified plane or planar surface to
a desired depth.
To demonstrate the hole functionality, we will open up the Hole_Definition part, which initially looks
like the following.
When you create holes, you generally have four types of placement: Linear, Radial, Diameter and
Coaxial. We will use the next sections to show these different types.
LINEAR HOLE
We will start by clicking on the hole feature, and then we will click on the model in the location shown
below.
A preview of the hole appears on the model, as shown in the next figure. For a linear placement, there
are a number of different drag handles that appear on the hole feature. They are shown in the figure.
Depending on the type of hole you are creating, you will see different options in the dashboard. For a
straight hole (circular cross-section along the entire length), the options represent the following.
For this first linear hole, we will change the diameter to 0.625 and change the depth option to Through
All. Our preview will look like the next figure.
We still have two drag handles that need to be addressed. We will drag the two handles over to the
following references.
In the dashboard, we will click on the Placement slide-up panel, which looks like the following.
We can see the two references and the respective dimensions. We can also see a middle column that
defines the relationship to the references. For the FRONT datum plane row, we will click on the word
Offset and change the option to Align, and change the remaining offset dimension to 1.000, as
shown below.
This will make the center of the hole line up with the FRONT datum plane, as we can see on the model
preview.
Now we will click on the green check mark to complete this first hole, which will look like the following.
COAXIAL HOLE
We are going to create another straight, simple hole. The first thing we are going to do is turn on the
display of axes. Next, we will create a new hole and pick on the axis A_10 that is going through the
large circle on the end.
You will see an outline of the hole that is lined up with the axis that we selected. We will change the
diameter value to 1.0, and the depth to Through All. When we do this, our preview looks like the
following.
The depth of the hole seems to have gone to zero even though it isnt. The reason it does this is
that there still is not enough information to fully define this hole. To see what is left, we need to expand
file:///C|/Documents and Settings/Administrator/Desktop/PROENGINEER WILDFIRE 3.0/hole.htm (7 of 16)1/9/2005 8:50:25 AM
With a coaxial hole, the primary reference is the axis that we picked. The hole knows it is lined up with
the axis, but it doesnt know where it starts from. This is the Secondary Reference. Therefore, pick in
the Secondary References field, and then pick on the large, flat, circular surface. The preview now
looks like the following.
Click on the green check mark to complete this hole. The model now looks like the following.
RADIAL/DIAMETER HOLE
The next hole we create will demonstrate the Radial and/or Diameter placement, but we will also shake
it up a bit and switch from a straight, simple hole to a standard hole. Therefore, we will start by creating
a new hole feature, and then pick on the following surface.
The hole will initially preview like a Linear placement, as we can see in the following figure.
Before we start dragging handles, we should open up the Placement panel, and use the pull-down
field at the top right to change from Linear to Radial, as shown in the next figure.
In the figure above, you can see the four placement options. In this example, we use Radial, but we
could pick on Diameter and the rest of these steps would be identical. The difference between Radial
Change this radius dimension to 0.875, as shown in the above figure. The second drag handle must
be tied to a datum plane or planar surface that either passes through the A_10 axis, or is parallel to an
imaginary plane that would pass through the axis. Therefore, we will drag the reference handle over to
the FRONT datum plane.
When we do this, an angle will appear on the preview, as we can see in the next figure.
We will modify this angle dimension to 60.0. The Placement panel will look like the following.
Now that we have successfully placed this hole, we will change it to a standard hole. NOTE: You could
have selected standard to begin with, but I think it is easier to make the standard hole once it is fully
placed, otherwise, you wont see the correct shape in the preview.
Click on the Standard Hole icon in the lower left of the dashboard. This will change the dashboard to
look like the following (with the Shape panel expanded).
For the Thread Type field, we will keep the UNC option. Other options include UNF and ISO. For the
Thread Size field, use the pull-down to select a 10-24 thread. For the depth option, we will pick on the
Through All icon. This will make the Depth Value disappear.
At the end of the dashboard icons, we will keep the Tapping and Countersink options selected. Up in
the Shape panel, we want to change the depth of the thread to Thru Thread, so the threaded surface
goes along the entire length of the tapped hole. We will leave the angle and diameter for the
countersink alone, but we could change this if we needed. Our dashboard should now look like the
following.
If we look at the preview on the part, we can see the shape and size has updated to reflect this
standard hole. If we had not placed it fully, it would still look like a big yellow cylinder.
If we expand the Note panel, we can see the standard not that it creates by default. We can edit and
add to this note. This note can be shown in the drawing to save us some time re-creating it.
We will now click on the green check mark to complete the hole. The model will look like the following.
To hide the view of the note on the model, we can go to Tools, Environment and uncheck the 3D
Notes option. Our model will now look like the following.
Save and close this model. We will come back to it in the lesson on Patterns.
SKETCHED HOLES
The last option we have for the hole feature is a sketched hole. It is created by starting with a straight
hole. In the dashboard, use the first pull-down field to change from Simple to Sketched. When we do
this, the dashboard looks like the following.
LESSON SUMMARY
Hole features should be used over extruded or revolved cuts. Placing the hole is simple and
straightforward once you know what you need to select, and you can pick from standard, industry sizes
and take the guesswork out of knowing the exact thread diameter to use.
As you saw in this lesson, you can mix and match hole placement types and hole types. But perhaps
the biggest benefit to using the hole feature is when you go to pattern, which we will see in a later
lesson.
EXERCISES
Open up the Hole_Exercise.prt part and add the three holes shown on the figure on the next page.