Professional Documents
Culture Documents
MAINTENANCE MANUAL
3
4
5
Device numbers
.0
.1
.2
.3
.4
.5
.6
.7
.8
.9
.10
.11
.12
.13
.14
.15
GDT
RS232
Imem
Xmem
Second RS232
Card Memory
Radio
Distance
PVX/Alidad
Servo
Tracker
Angle
6-1
MAINTENANCE MANUAL
600ATS.01.321.00.1
Info codes
Code
Type
Description
1
2
3
3
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20.i
21.i
22.i
23.i
24.i
25
26.i
27
28.i
29
30.i
31
32
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
6-2
MAINTENANCE MANUAL
33
600ATS.01.321.00.1
34
35.i
36
37
38
39
40
3
3
3
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
3
3
Wrong type
UDS Program memory full
Square root of neg. value
Not enough data for calculation
1
3
4
4
6-3
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
6-4
MAINTENANCE MANUAL
600ATS.01.321.00.1
Radio unit
Code
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
Type
Description
3
3
EEPROM error
EEPROM OK
PLL unable to lock, hardware
Invalid channel
Georadio ver. x.x, after radio reset
No Access, S register. or locked command.
Transmission blocked, Japanese radios only.
Radio error NAK
Radio error CAN
Radio not connected.
Time-out after radio command
Time-out Ack/Nak
Invalid channel
6-5
135
136
137
138
139
Card Memory
Code
140
141
142
143
144
145
146
147
148
149
Type
Description
General system error
6-6
MAINTENANCE MANUAL
600ATS.01.321.00.1
Servo system
Code
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
Type
Description
3
3
3
3
3
3
3
3
3
3
3
3
3
3
Distance unit
Code
170
171
172
173
174
175
176
177
178
Type
Description
3
3
3
3
3
6-7
MAINTENANCE MANUAL
600ATS.01.321.00.1
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199.i
200
201
202
203
204
205
206
207
207.1
210
211
212
213
214
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
6-8
MAINTENANCE MANUAL
600ATS.01.321.00.1
215
Wrong Src_type
216
217
218.i
219
3
3
3
3
Wrong Dst_type
Serial channel RS-buffer overflow
Input string overflow
Wrong parameter
Angle unit
Code
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
Type
Description
3
3
3
3
3
3
3
3
3
3
3
3
248
Process failed.
249
250
251
252
253
254
255.i
Fatal error
6-10
Descriptions
The following pages will describe some of the most common info codes.
Code
Explanation
The instrument is tilted too much. The compensator cant compensate for the inclination.
The operation was carried out in the wrong face (C1/C2).
Tries to use a display- or output-table that doesnt exist.
The vertical angle is less than 15 gon from the horizontal angle during a collimation test.
Appear if a external device (ex. GDT 500) or internal (ex. distance
unit) unit isnt active.
Appear if prg. 22 or 28 is activated in remote mode.
Appear if prg. 22 or 28 is activated in Autolock mode.
Appear if a collimation test is carried out. Collimation test only possible to perform with the control unit attached to the instrument.
General communication error.
Wrong label entered.
General serial communication error.
Overrun error
Parity error
Framing error
Received error
Error occur during a communication session.
The operation was carried out while the instrument was in an illegal
mode.
2
5
6
10
16
17
18
19
20
21.i
21.1
21.2
21.4
21.8
23
24
30
31
33
34
39
40
6-11
MAINTENANCE MANUAL
600ATS.01.321.00.1
41
43
44
48
Calculation error.
Call is used in too many steps (max. 4 steps).
Station labels has been change since the station was established. Station isnt established.
Wrong configuration number. (check prg. version)
Checksum error.
Instrument/Control Unit not initiated.
Tries to position the instrument to an illegal angle.
Calculation error. Could be follow up info to 175.
Calculation error. Could be follow up info to 175.
50
51
54
153
171
172
173
174
175
190
191
197
198
199
200
201
206
207
207.1
211
6-12
212
214
215
216
217
218
219
227
231
6-13