Professional Documents
Culture Documents
SKF General Conditions for technical assistance and advice (available at www.skf.com) shall apply to this report.
SKF accepts no variation of any of these conditions unless confirmed in writing by SKF.
SKF is a registered trademark of the SKF Group.
SKF Group 2013
The contents of this publication are the copyright of SKF and may not be reproduced, duplicated, copied, transferred, distributed, stored, modified, downloaded or otherwise exploited for any
commercial use without the prior written approval of SKF.
Table of Contents
1.
Designation: 6309
1.1 Bearing life
1.2 Minimum load
1.3 Frictional moment - power loss
1.4 Bearing frequencies
1.5 Influence of load and lubricant viscosity on adjusted reference speed
1.6 Relubrication intervals
1.7 Viscosity
1.8 Equivalent dynamic bearing load
1. Designation: 6309
Bearing Data
d
45.0 mm
100.0 mm
25 mm
55.3 kN
31.5 kN
1.1
Bearing life
Input Parameters
Select bearing internal radial clearance
4 kN
0.5 kN
1800 r/min
r
Radial load
a
Axial load
i
Rotational speed of the inner ring
Operating temperature
Bearing outer ring
80 C
specification method
c
Cleanliness
classification(recommended)
Viscosity at 40 C
Viscosity at 100 C
Result
L
506400 hour
20.7
10mh
SKF rating life
SKF
SKF life modification factor a
SKF
Viscosity ratio
2.08
P
Equivalent dynamic bearing load
4 kN
0.55
2
10.4 mm /s
24500 hour
C/P
Load ratio
13.8
c
Factor for contamination level
1
Required kinematic viscosity for =1
10h
Basic rating life
1.2
Minimum load
Input Parameters
n
1800 r/min
Operating temperature
Bearing outer ring
80 C
i
Rotational speed of the inner ring
2
120 mm /s
2
12 mm /s
Viscosity at 40 C
Viscosity at 100 C
Result
F
0.18 kN
rm
Minimum radial load
1.3
Input Parameters
F
4 kN
0.5 kN
1800 r/min
Operating temperature
Bearing outer ring
80 C
r
Radial load
a
Axial load
i
Rotational speed of the inner ring
Viscosity at 100 C
2
120 mm /s
2
12 mm /s
Lubrication
Grease
Viscosity at 40 C
Result
M
117.2 Nmm
78.5 Nmm
0 Nmm
0 Nmm
M
Total frictional moment
195.6 Nmm
rr
Rolling frictional moment
sl
Sliding frictional moment
seal
Frictional moment of the seals
drag
Frictional moment of drag losses
37 W
r
Power loss
2
21.6 mm /s
232.4 Nmm
6.0E-8
start
Starting torque
rs
Replenishment/starvation constant
1.4
Bearing frequencies
Input Parameters
n
1800 r/min
0 r/min
i
Rotational speed of the inner ring
e
Rotational speed of the outer ring (only used to calculate the bearing
frequencies)
Result
f
30 Hz
0 Hz
11.4 Hz
58.7 Hz
148.9 Hz
91.1 Hz
117.3 Hz
i
Rotational frequency of the inner ring
e
Rotational frequency of the outer ring
c
Rotational frequency of the rolling element and cage assembly
r
Rotational frequency of a rolling element about its own axis
ip
Over-rolling frequency of one point on the inner ring
ep
Over-rolling frequency of one point on the outer ring
rp
Over-rolling frequency of one point on a rolling element
1.5
Input Parameters
Select bearing internal radial clearance
4 kN
0.5 kN
Viscosity at 40 C
2
120 mm /s
Lubrication
Grease
r
Radial load
a
Axial load
Result
f
0.84
0.84
p
Adjustment factor for bearing load P
v
Adjustment factor for grease base oil viscosity
tot
f f with grease lubrication
p v
n
ar
Adjusted reference speed with grease lubrication
1.6
12700 r/min
Relubrication intervals
Input Parameters
F
4 kN
0.5 kN
r
Radial load
a
Axial load
1800 r/min
Rotating ring
Shaft orientation
Horizontal shaft
Operating temperature
Bearing outer ring
80 C
i
Rotational speed of the inner ring
Result
t
8300 hour
12 g
f
Relubrication interval
p
Grease quantity to be added when replenishing
1.7
Viscosity
Input Parameters
n
1800 r/min
Operating temperature
Bearing outer ring
80 C
i
Rotational speed of the inner ring
2
120 mm /s
2
12 mm /s
Viscosity at 40 C
Viscosity at 100 C
Result
2
21.6 mm /s
2
10.4 mm /s
2
42.5 mm /s
Viscosity ratio
2.08
1
Required viscosity at operating temperature for =1
ref
Required viscosity at 40 C for =1
1.8
Input Parameters
Select bearing internal radial clearance
4 kN
0.5 kN
r
Radial load
a
Axial load
Result
P
Equivalent dynamic bearing load
4 kN