Professional Documents
Culture Documents
909
Nokia Flexi WCDMA Base Station, Rel. Flexi
WBTS4.0 and Flexi WBTS4.5, Product
Documentation, v.5
DN7086754
Issue 7-1 en
31/10/2008
1 (87)
The information in this document is subject to change without notice and describes only the
product defined in the introduction of this documentation. This documentation is intended for the
use of Nokia Siemens Networks customers only for the purposes of the agreement under which
the document is submitted, and no part of it may be used, reproduced, modified or transmitted in
any form or means without the prior written permission of Nokia Siemens Networks. The
documentation has been prepared to be used by professional and properly trained personnel,
and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes
customer comments as part of the process of continuous development and improvement of the
documentation.
The information or statements given in this documentation concerning the suitability, capacity, or
performance of the mentioned hardware or software products are given as is and all liability
arising in connection with such hardware or software products shall be defined conclusively and
finally in a separate agreement between Nokia Siemens Networks and the customer. However,
Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions
contained in the document are adequate and free of material errors and omissions. Nokia
Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which
may not be covered by the document.
Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NO
EVENT WILL NOKIA SIEMENS NETWORKS BE LIABLE FOR ERRORS IN THIS
DOCUMENTATION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL,
DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT
NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS
OPPORTUNITY OR DATA, THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE
INFORMATION IN IT.
This documentation and the product it describes are considered protected by copyrights and
other intellectual property rights according to the applicable laws.
The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark of
Nokia Corporation. Siemens is a registered trademark of Siemens AG.
Other product names mentioned in this document may be trademarks of their respective owners,
and they are mentioned for identification purposes only.
Copyright Nokia Siemens Networks 2008. All rights reserved.
2 (87)
DN7086754
Issue 7-1 en
31/10/2008
Contents
Contents
Contents 3
Summary of changes in Flexi WCDMA BTS Optional Items
Description 5
1
Flexi mounting kit for floor, wall and pole (FMFA) description 9
Flexi mounting covers for back and front (FMCA and FMCB)
description 21
6
6.1
6.2
6.3
8
8.1
8.2
8.3
8.4
9.4
10
10.1
10.2
10.3
10.4
11
12
9.1
9.1.1
9.2
9.3
DN7086754
Issue 7-1 en
31/10/2008
25
48
3 (87)
4 (87)
12.1
12.2
12.3
13
13.1
13.2
13.3
14
14.1
14.2
15
15.1
15.2
15.3
16
16.1
16.2
17
17.1
17.2
17.3
18
77
80
DN7086754
Issue 7-1 en
31/10/2008
DN7086754
Issue 7-1 en
31/10/2008
5 (87)
6 (87)
DN7086754
Issue 7-1 en
31/10/2008
Figure of the FSEB PWB added in section Flexi System External Alarm
(FSEB) interfaces.
Section Flexi System External GPS Mediator (FSEG) operation added.
Section Flexi System External GPS Mediator (FSEG) dimensions and
weight added.
Section Flexi System External GPS Mediator (FSEG) interfaces added.
Section Flexi System External Alarm Box (FSEB) dimensions and weight
added.
Figures in section Flexi Power Module (FPMA) and sub-modules (FPAA
and FPBA) operation updated.
Figure of LED indication removed from section Flexi power DC/DC submodule LED indications.
Section Flexi Power AC/DC sub-module (FPAB) description updated with
information on FPAB LEDs and a figure of FPAB connectors added.
Section FCOA cabinet optional items updated with information on the
FMBA and wind breaker.
DN7086754
Issue 7-1 en
31/10/2008
7 (87)
8 (87)
DN7086754
Issue 7-1 en
31/10/2008
Flexi mounting kit for floor, wall and pole (FMFA) description
In floor mounting, the plinth is fixed directly onto the floor. To meet
the Telcordia GR-63-CORE Vibrational requirements for earthquake
Zone 4 requirement, the maximum number of modules in a stack is
five (maximum total height 15 U). To meet the Telcordia GR-63CORE Vibrational requirements for earthquake Zone 2 requirement,
the maximum number of modules in a stack is nine (maximum total
height 22 U).
In wall mounting, the plinth is fixed onto the wall either by using
adapter mechanics or directly to the wall. The maximum number of
modules per plinth is two.
In pole mounting, the plinth is fixed onto the pole mounting kit
(VMPB) by using adapter mechanics. Adapters are needed to
reduce the influence of non-parallel surfaces of the mounting
brackets. The maximum number of modules per plinth is two.
The FMFA delivery includes two fixing plates for the casings. Used in
pole and wall installations, the plates are attached across two
module casings on both sides of the modules.
See the following figure for an isometric view of the FMFA.
DN7086754
Issue 7-1 en
31/10/2008
9 (87)
DN7082497
Figure 1.
DN7099438
Figure 2.
10 (87)
Adapter mechanics
DN7086754
Issue 7-1 en
31/10/2008
Flexi mounting kit for floor, wall and pole (FMFA) description
The plinth has a back stop that prevents installing the BTS too near to a
wall (40 mm).
The compartment behind the front panel of the plinth is used as a storage
place, for example, for seal caps.
FMFA dimensions and weight
The dimensions and weight of the FMFA are presented in the following
table.
Table 1.
Property
Value
Height
69 mm
(2.7 in.)
Width
455 mm
(17.9 in.)
Depth
459 mm
(18.1 in.)
Weight
DN7086754
Issue 7-1 en
31/10/2008
11 (87)
See the following figure for the external fixing interfaces of the FMFA.
Casing locking
points
ESD Stud
Modules grounding
Anchoring points
to floor
DN7082504
Figure 3.
12 (87)
DN7086754
Issue 7-1 en
31/10/2008
DN70415461
Figure 4.
See the following table for the delivery contents of the VMPB.
Table 2.
DN7086754
Issue 7-1 en
31/10/2008
Delivery contents
Item
Quantity
Mounting blocks
2 pcs
M8x25 bolts
8 pcs
M10x120 bolts
4 pcs
M10x200 bolts
4 pcs
M10x300 bolts
4 pcs
Washers
4 pcs
13 (87)
See the following table for dimensions and weight of the VMPB.
Table 3.
Property
Value
Height
60 mm (2.4 in.)
Width
Depth
300 mm (11.8)
Weight
14 (87)
DN7086754
Issue 7-1 en
31/10/2008
The pole can between 60 mm (2.4 in.) and 120 mm (4.7 in.) in diameter.
There are two sets of fixing points on the installation plate. The FPIA can
carry the weight of 5 kg (11 lbs).
DN7086754
Issue 7-1 en
31/10/2008
15 (87)
16 (87)
DN7086754
Issue 7-1 en
31/10/2008
Bolt M8x20
Fixingpoints
64mm (2.5 in.)
Bolt M10X120
105 mm thread
Fixingpoints
184mm (7.2 in.)
Figure 5.
The width of the fixing points is 184 mm (7.2 in.) and 64 mm (2.5in.). There
are fixing points in three sides of the FPKA. The M10 screws should be
tightened to 30Nm and the M8 screws 20 Nm. The FPKA can carry the
maximum weight of 160 kg (352.7 lbs).
The delivery contents of the FPKA are listed in the following table.
DN7086754
Issue 7-1 en
31/10/2008
17 (87)
Item
Quantity
FPKA Bracket
1 pcs.
Bolt M8 x 20
6 pcs.
Bolt restrainer
2 pcs.
1 pcs.
2 pcs.
DN70424764
Figure 6.
18 (87)
DN7086754
Issue 7-1 en
31/10/2008
DN70424752
Figure 7.
DN7086754
Issue 7-1 en
31/10/2008
19 (87)
DN70424776
Figure 8.
20 (87)
DN7086754
Issue 7-1 en
31/10/2008
Flexi mounting covers for back and front (FMCA and FMCB)
description
DN7086754
Issue 7-1 en
31/10/2008
21 (87)
Front cover
Back cover
2 x safety catch
Grounding cable
DN7082516
Figure 9.
FMCA dimensions
The dimensions of the FMCA are presented in the following table.
Table 4.
Property
Front cover
Back cover
Height
128 mm
128 mm
(5 in.)
(5 in.)
492 mm
446 mm
(19.4 in.)
(17.6 in.)
100 mm
37 mm
(3.9 in.)
(1.5 in.)
Width
Depth
22 (87)
DN7086754
Issue 7-1 en
31/10/2008
Flexi mounting covers for back and front (FMCA and FMCB)
description
Table 5.
Property
Front cover
Back cover
Height
83 mm
83 mm
(3.3 in.)
(3.3 in.)
492 mm
446 mm
(19.4 in.)
(17.6 in.)
100 mm
37 mm
(3.9 in.)
(1.5 in.)
Width
Depth
Table 6.
DN7086754
Issue 7-1 en
31/10/2008
Grounding cable
Property
Value
Length
Thickness
16 mm2 (5 AWG)
23 (87)
24 (87)
DN7086754
Issue 7-1 en
31/10/2008
6
6.1
6.2
DN7086754
Issue 7-1 en
31/10/2008
25 (87)
Table 7.
FSEB dimensions
Property
Value
Width
335 mm
(13.2 in.)
Height
94 mm
(3.7 in.)
Depth
182 mm
(7.2 in.)
Weight
Max. 2 kg
(4.4 lbs)
6.3
26 (87)
DN7086754
Issue 7-1 en
31/10/2008
ESD
Grounding point
EAC M16
UltraSite and Talk
swap cases
BTS interconnection
cable
DN70283679
Figure 10.
FSEB interfaces
PWB interface
The PWB interface and connectors are presented in the table below.
Table 8.
Interface
Type
Description
EACX-I
Sub-D37, female
6 alarm outputs
(ESM extension,
compatible to EAC on
ESM)
EACX-S
10 SMDK1/6-3.5
DN7086754
Issue 7-1 en
31/10/2008
Screw terminal
ESM
Sub-D37, male
27 (87)
Table 8.
Interface
Type
Description
*EACX-II
Sub-D37, female
Smoke-Detector
Power X4114
EACX-II(D37)
EACX-I(D37)
Not in use
DN70410509
Figure 11.
28 (87)
FSEB PWB
DN7086754
Issue 7-1 en
31/10/2008
DN70154491
Figure 12.
DN7086754
Issue 7-1 en
31/10/2008
29 (87)
FSEC dimensions
The dimensions of the Flexi system external OVP box are presented in the
following table. The FSEC is made of aluminium.
Table 9.
FSEC dimensions
Property
Value
Width
95 mm
(3.7 in.)
Height
155 mm
(6.1 in.)
Depth
155 mm
(6.1 in.)
Weight
FSEC connectors
In the FSEC, there are screw terminals for input and output cables. There
are four pieces of screw terminals for AWG 2 cables and for earthing two
PEs (Protecting earth GND) terminals for AWG 2 cable size.
30 (87)
DN7086754
Issue 7-1 en
31/10/2008
8
8.1
DN7086754
Issue 7-1 en
31/10/2008
31 (87)
12V DC
30 (FYHA) or
100m (FYHB)
BTS/Iub
48V DC
AC in
EAC
DN70468865
Figure 13.
32 (87)
overvoltage protection
DN7086754
Issue 7-1 en
31/10/2008
DN7086754
Issue 7-1 en
31/10/2008
33 (87)
Max n = 5
12V DC
BTS/Iub
EAC
48V DC
AC in
EAC
BTS n
...
Figure 14.
8.2
BTS 1
Master BTS
Table 10.
Property
Value
Width
335 mm
(13.2 in.)
Height
94 mm
(3.7 in.)
Depth
182 mm
(7.2 in.)
Weight
Max. 2 kg
(4.4 lbs)
34 (87)
DN7086754
Issue 7-1 en
31/10/2008
8.3
Table 11.
Interface
Type
Description
BTS sync in
MDR26
Synchronization interface
to FSMB
BTS PSU
Screw terminal
GPS Module
MDR26
Interface to FYGA
GND
Screw terminal
Module grounding
See the following figure for the FSEG printed wiring board.
DN7086754
Issue 7-1 en
31/10/2008
35 (87)
BTS
SYNC IN
GPS
MODULE
BTS PSU
GND
DN70454901
Figure 15.
8.4
GPS antenna
The GPS antenna with an integrated receiver has to be installed outside
for satellite visibility. The antenna is directly connected to the
synchronisation input of the System Module.
DC power feed for the receiver is supplied through the combined power
and data cable. The System Module provides a power feed of 48 V DC that
is converted into 12 V DC using Flexi System External GPS Mediator
(FSEG).
36 (87)
DN7086754
Issue 7-1 en
31/10/2008
See also section Installing the GPS System in Installing Flexi WCDMA
BTS Optional Items.
DN7086754
Issue 7-1 en
31/10/2008
37 (87)
38 (87)
DN7086754
Issue 7-1 en
31/10/2008
9
9.1
Flexi Power Module (FPMA) and submodules (FPAA and FPBA) description
Flexi Power Module (FPMA) and sub-modules
(FPAA and FPBA) operation
Flexi Power Module (FPMA) is an optional module. It comprises FPMA
mechanics and AC and DC interfaces. The actual power sub-modules are
the following:
.
DN7086754
Issue 7-1 en
31/10/2008
39 (87)
Type label
DN70230045
Figure 16.
DN7084386
Figure 17.
40 (87)
DN7086754
Issue 7-1 en
31/10/2008
9.1.1
Operation
The FPMA can support 1-phase and 3-phase AC input. The nominal input
voltage is 200-240 V AC (the operating voltage range is 180 - 276 V AC).
The maximum output power from the FPMA is 4kW (with 4 FPAAs).
Flexi Power AC-DC sub-module (FPAA)
The main function of the FPAA is to provide the BTS with nominal 48 V DC
power from an AC supply. Maximum DC output power of one FPAA
module is 1000 W. A nominal 48 V DC supply is intended for BTS internal
use only (a nominal 48 V DC supply is not intended for 3rd party
equipment because they may require lower conducted emission level than
EN55022 Class A). It should be especially noted that an external lead acid
battery for longer backup times cannot be connected to nominal 48 V DC
supply. (This is because the temperature compensation of charging
voltage is not supported). The FPAA includes its own integrated selfcontrolled fan. In case the fan fails, an alarm is generated and the FPAA
has to be replaced (the fan alone cannot be replaced).
Flexi Power Battery sub-module (FPBA)
The Flexi Power Battery Sub-Module (FPBA) is a separate optional submodule used together with the FPAA.
The FPBA provides short-term battery backup time when the AC power
mains is down on a Flexi BTS site. The FPBA is a lithium ion battery. The
maximum DC output power from one FPBA module is 1000 W. The input
power for the BTS cannot exceed the maximum output power of the
installed batteries. Otherwise the batteries do not provide the BTS with the
needed power during power failure.
9.2
Table 12.
Property
FPMA
Height
133 mm/3 U
(5.2 in.)
Width
447 mm
(17.6 in.)
DN7086754
Issue 7-1 en
31/10/2008
41 (87)
Table 12.
Property
FPMA
422 mm
(16.6 in.)
560 mm
(22.1 in.)
Weight (empty)
< 11 kg
(< 24.3 lbs)
9.3
Weight
28 kg
(61.9 lbs)
Table 13.
Connector
Type
Purpose
Power supply in
Terminal block
Grounding
2 x M5
Module grounding
42 (87)
DN7086754
Issue 7-1 en
31/10/2008
Table 14.
Connector
Type
Purpose
AC cable connector
Mate-N-Lock
AC input
DC connector
DC output
Alarm connector
2 x RJ-45*
Alarms**
tri-colour LED
*for chaining
**Alarm 1 (AL01): AC input failure (alarm is sent when AC input voltage is
missing or it is out of range).
**Alarm 2 (AL02): maintenance needed (possible reasons are unit failure,
cooling fan failure, output power is low or over temperature shut down is
ON).
FPBA front panel connectors
There is a stand-by switch on the front panel of the FPBA.
The connectors on the FPBA front panel, their types and purposes are
listed in the table below.
Table 15.
Connector
Type
Purpose
DC input/output connector
Alarm connector
2 x RJ-45*
Alarms**
tri-colour LED
*for chaining
DN7086754
Issue 7-1 en
31/10/2008
43 (87)
9.4
Table 16.
Colour
Explanation
Yellow
Green
Normal operation
Red
Alarm or fault
Red, blinking
See the following figure for the location of the FPAA LED.
LED
DN70350654
Figure 18.
44 (87)
FPAA LED
DN7086754
Issue 7-1 en
31/10/2008
Table 17.
Colour
Explanation
Yellow
Ggreen
Charging
Discharging
Minor alarm
Red
LED
DN70350678
Figure 19.
DN7086754
Issue 7-1 en
31/10/2008
FPBA LED
45 (87)
46 (87)
DN7086754
Issue 7-1 en
31/10/2008
10
10.1
DN7086754
Issue 7-1 en
31/10/2008
47 (87)
DN70150502
Figure 20.
10.2
Table 18.
Property
Value
Height
90 mm (2U)
(3.5 in.)
Width
447 mm
(17.6 in.)
422 mm
(16.6 in.)
560 mm
(22.1 in.)
48 (87)
DN7086754
Issue 7-1 en
31/10/2008
Table 18.
Property
Value
Weight
< 15 kg
(< 33.1 lbs)
10.3
Table 19.
Connector
Connector type
Purpose
Input connector
M10 bolts
DC input
Output connector
M10 bolts
DC output
Alarm connectors
2 x RJ-45*
Alarms**
*for chaining
**Alarm 1 (AL01): DC input failure (alarm is sent when DC input voltage is
missing or it is out of range).
**Alarm 2 (AL02): maintenance needed (possible reasons are unit failure,
cooling fan failure, output power is low or over temperature shut down is
ON).
The FPDA front panel is presented in the following figure.
DN7086754
Issue 7-1 en
31/10/2008
49 (87)
DC Input cabling
Alarm cabling
DC Output cabling
LED
DN70141402
Figure 21.
10.4
Table 20.
50 (87)
Colour
Explanation
Green
Normal operation
Red
Alarm or fault
Yellow
Stand-by
Red, blinking
DN7086754
Issue 7-1 en
31/10/2008
DN7086754
Issue 7-1 en
31/10/2008
51 (87)
52 (87)
DN7086754
Issue 7-1 en
31/10/2008
11
LED
DN70265249
Figure 22.
DN7086754
Issue 7-1 en
31/10/2008
53 (87)
Table 21.
Property
Value
90 - 276 V AC
Output voltage
56 V DC at 500 W
AC input
(row connector)
DC output
(multi-beam connector)
DN70407333
See the following figure for installing the FPAB in the RF Module.
54 (87)
DN7086754
Issue 7-1 en
31/10/2008
DN70286831
Figure 23.
FPAB dimensions
The dimensions of the FPAB are presented in the following table.
Table 22.
DN7086754
Issue 7-1 en
31/10/2008
FPAB dimensions
Property
Value
Width
Height
73 mm (2.9 in.)
Depth
Weight
55 (87)
Table 23.
56 (87)
Colour
Explanation
Yellow
Green
Normal operation
DN7086754
Issue 7-1 en
31/10/2008
12
12.1
62/92 Ah batteries and Flexi Battery Mounting Kit for FCIA (FMBB)
DN7086754
Issue 7-1 en
31/10/2008
57 (87)
DN70253985
Figure 24.
12.2
FCIA cabinet
58 (87)
DN7086754
Issue 7-1 en
31/10/2008
one power distribution unit (WPU) with one control unit (CU), and
The power distribution unit mainly distributes the input AC mains to the
rectifier units. The control unit controls the rectifier power units and
monitors the alarms in the event of low supply voltage, or if the MIBBU
enters the battery backup mode in the event of an AC mains failure. The
alarm generated by the control unit is forwarded to the BTS O&M software.
Flexi Battery Mounting Kit for FCIA (FMBB)
Flexi Battery Mounting Kit (FMBB) is needed when using batteries or the
MIBBU solution in FCIA. The mounting kit is installed at the bottom of the
cabinet.
12.3
Table 24.
Property
Value
Height
1800 mm / 40.5U
(70.87 in.)
DN7086754
Issue 7-1 en
31/10/2008
59 (87)
Table 24.
Property
Value
Width
600 mm
(23.62 in.)
Depth
600 mm
(23.62 in.)
60 (87)
Weight
62 kg
(empty cabinet)
(136 lbs.)
36 U
DN7086754
Issue 7-1 en
31/10/2008
13
13.1
it houses the Flexi cabinet site support module (FCSA) that provides
long-term battery back-up and a 4U-high IP55-protected space for
Line Terminal Equipment (LTE)
together with Flexi cabinet air filter (FCFA), it protects the BTS in
extremely dirty conditions
DN7086754
Issue 7-1 en
31/10/2008
61 (87)
DN70138414
Figure 25.
13.2
FCOA cabinet
62 (87)
DN7086754
Issue 7-1 en
31/10/2008
The air filter is installed in the back of the cabinet, replacing the original
back wall. It consists of a filter element, 8 x diagonal fans, a pressure
sensor, a control logic, and back wall mechanics. The wind plate is
installed in the cabinet door.
The control of the FCFA fans is based on a pressure sensor. The pressure
sensor measures pressure inside the cabinet and this information is then
used for controlling the fan speed.
The air filter is presented in the following figure.
DN70150526
Figure 26.
DN7086754
Issue 7-1 en
31/10/2008
Air filter
63 (87)
64 (87)
DN7086754
Issue 7-1 en
31/10/2008
Heat
Exchanger
MIBBU
Control
card
LTE Space
Batteries
FMBA
DN70150538
Figure 27.
Site support
Fire detector
The fire detector is installed on the cabinet roof, and the cables are routed
to the Flexi System External Alarm (FSEB).
The following figure presents the fire detector.
DN7086754
Issue 7-1 en
31/10/2008
65 (87)
DN70150541
Figure 28.
Fire detector
Overvoltage protection
Flexi System External OVP (FSEC) is IP-protected box for overvoltage
protection and power terminals. FSEC is installed on the cabinet roof. For
more information on FSEC, see Flexi System External OVP (FSEC)
description.
13.3
Table 25.
Property
Value
Height
1550 mm
(61 in.)
Width
770 mm
(30.3 in.)
66 (87)
DN7086754
Issue 7-1 en
31/10/2008
Table 25.
Property
Value
Depth
770 mm
(30.3 in.)
930 mm
(36.6 in.)
1020 mm
(40.2 in.)
Weight
Max. 80 kg
(empty cabinet)
(177 lbs)
Weight
104 kg
(230 lbs)
Weight
110 kg
(243 lbs)
Total weight
365 kg
(807 lbs)
40 U
(30 U horizontally + 5 U + 5 U vertically
DN7086754
Issue 7-1 en
31/10/2008
21 U
(16 U horizontally + 5 U vertically)
67 (87)
68 (87)
DN7086754
Issue 7-1 en
31/10/2008
14
14.1
DN7086754
Issue 7-1 en
31/10/2008
69 (87)
DN70324735
Figure 29.
70 (87)
DN7086754
Issue 7-1 en
31/10/2008
DN70324723
Figure 30.
The FMSA provides installation space for up to any two Flexi 3U modules
and the plinth (6U in total). It is installed on a pole or wall.
The FMSB provides space for up to any six Flexi 3U modules and the
plinth (18U in total). It is installed on the floor.
DN7086754
Issue 7-1 en
31/10/2008
71 (87)
14.2
Table 26.
Property
Value
Height
Width
Depth
Weight (empty)
12 kg (26.5 lbs.)
6U
Table 27.
72 (87)
Property
Value
Height
Width
Depth
Weight (empty)
21 kg (46.3 lbs.)
18U
DN7086754
Issue 7-1 en
31/10/2008
15
15.1
DN7086754
Issue 7-1 en
31/10/2008
73 (87)
2G
System
Module
1 U free space
RF Module
DN7082146
Figure 31.
Before the mounting kit can be installed, the following parts are removed
from the lower half of the GSM/EDGE UltraSite cabinet:
.
3 x fans,
The mounting kit consists of one dual rack in which one System Module
and one RF Module are installed, one single rack for the second RF
Module installation, and cables. There is a remaining space of 1 U in the
single rack when the RF Module is installed.
74 (87)
DN7086754
Issue 7-1 en
31/10/2008
15.2
DN7086754
Issue 7-1 en
31/10/2008
75 (87)
Dual rack
FRONT
BACK
Single rack
FRONT
BACK
DN7082037
Figure 32.
76 (87)
DN7086754
Issue 7-1 en
31/10/2008
15.3
Dual rack
Single rack
Height
694 mm
585 mm
(27.3 in.)
(23 in.)
302 mm
196 mm
(11.9 in.)
(7.7 in.)
395 mm
400 mm
(15.6 in.)
(15.8 in.)
6.2 kg
4.6 kg
(13.7 lbs)
(10.2 lbs)
0.7dB
0.7dB
Width
Depth
Weight
DN7086754
Issue 7-1 en
31/10/2008
77 (87)
78 (87)
DN7086754
Issue 7-1 en
31/10/2008
16
16.1
DN7086754
Issue 7-1 en
31/10/2008
79 (87)
DN70231874
Figure 33.
The mounting kit consists of a rack in which, for example, one WCDMA
System Module, up to three WCDMA RF Modules and one FPMA or
System Extension Module or FPDA are installed, and cables. The space
requirement for 5 x 3U modules is 15U.
For installation instructions, see section Installing modules in cabinet with
Flexi Mounting Kit Horizontal for 2G in the Installing Flexi WCDMA BTS
Modules in Cabinets document.
16.2
80 (87)
DN7086754
Issue 7-1 en
31/10/2008
Property
FMUB
Height
Width
Depth
Weight
(cables excluded)
The loss of RF cables
DN7086754
Issue 7-1 en
31/10/2008
0.7dB
81 (87)
82 (87)
DN7086754
Issue 7-1 en
31/10/2008
17
17.1
Figure 34.
The I-HSPA Adapter can be fitted to a Flexi BTS 2U module casing. When
used with the Flexi BTS module casing, the I-HSPA Adapter can be
installed with the Flexi WCDMA BTS in stand-alone configurations, such
as free-standing, wall mounted or pole mounted.
DN7086754
Issue 7-1 en
31/10/2008
83 (87)
Rear Cover
Casing
Front Cover
DN70287651
Figure 35.
The I-HSPA Adapter uses forced air cooling based on fresh air intake from
back to front. This allows it be installed either horizontally or vertically. The
contents of the I-HSPA Adapter delivery also include and air-blocking
plate, to be used if the I-HSPA Adapter is with the Flexi BTS 2U module
casing.
The I-HSPA Adapter features a lightweight aluminium alloy casing with
stainless steel alloy used for the fan carrier.
Figure 36.
84 (87)
DN7086754
Issue 7-1 en
31/10/2008
17.2
Table 28.
Width
Height
41 mm
Depth
299 mm
Weight
6.5 kg
Table 29.
17.3
Width
Height
84.1 mm
Depth
395 mm
Weight
12.5 kg
Table 30.
Front panel
identifier
Purpose
Interface type
Connector Type
BTS/Iub
BTS interface
RJ45 shielded
SFP/Ext 1
External transport
Ext 2
External transport
Ext 3
DN7086754
Issue 7-1 en
31/10/2008
RJ45 shielded
85 (87)
Table 30.
Front panel
identifier
Purpose
DC IN
DC IN
DN70282859
Figure 37.
86 (87)
Interface type
48VDC Power
Input
Connector Type
Multi-Beam XL RA
2 pin
EIF1
EIF2
EIF3
EIF4
DN7086754
Issue 7-1 en
31/10/2008
18
DN7086754
Issue 7-1 en
31/10/2008
87 (87)