Professional Documents
Culture Documents
SECTION
WW
CONTENTS
PRECAUTION ............................................................ 2
Precautions for Supplemental Restraint System
(SRS) AIR BAG and SEAT BELT PRE-TENSIONER .................................................................. 2
Wiring Diagrams and Trouble Diagnosis .................. 2
FRONT WIPER AND WASHER SYSTEM .................. 3
Components Parts and Harness Connector Location ........................................................................... 3
System Description .................................................. 3
LOW SPEED WIPER OPERATION ...................... 4
HI SPEED WIPER OPERATION ........................... 4
INTERMITTENT OPERATION .............................. 4
AUTO STOP OPERATION .................................... 5
WASHER OPERATION ......................................... 5
MIST OPERATION ................................................ 5
FAIL-SAFE FUNCTION ......................................... 5
COMBINATION SWITCH READING FUNCTION..... 5
CAN Communication System Description ................ 5
Wiring Diagram WIPER .................................. 6
Terminals and Reference Values for BCM ............... 8
Terminals and Reference Values for IPDM E/R ....... 9
Work Flow ................................................................ 9
Preliminary Inspection ............................................ 10
INSPECTION FOR POWER SUPPLY AND
GROUND CIRCUIT ............................................. 10
CONSULT-II Function (BCM) ..................................11
CONSULT-II OPERATION ...................................11
DATA MONITOR ................................................. 12
ACTIVE TEST ..................................................... 12
CONSULT-II Function (IPDM E/R) ......................... 13
CONSULT-II OPERATION .................................. 13
DATA MONITOR ................................................. 14
ACTIVE TEST ..................................................... 14
Front Wiper Does Not Operate .............................. 15
WW-1
2005 Maxima
WW
PRECAUTION
PRECAUTION
PFP:00011
Precautions for Supplemental Restraint System (SRS) AIR BAG and SEAT
BELT PRE-TENSIONER
EKS0094G
The Supplemental Restraint System such as AIR BAG and SEAT BELT PRE-TENSIONER, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Manual.
WARNING:
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be performed by an authorized NISSAN/INFINITI dealer.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
EKS0094H
Refer to PG-4, "POWER SUPPLY ROUTING CIRCUIT" for power distribution circuit.
When you perform trouble diagnosis, refer to the following:
WW-2
2005 Maxima
PFP:28810
A
EKS0094I
WW
WKIA3132E
System Description
EKS0094J
Both front wiper relays are located in the IPDM E/R (intelligent power distribution module engine room).
Wiper switch (combination switch) is composed of a combination of 5 output terminals and 5 input terminals. Terminal combination status is read by BCM (body control module) when switch is turned ON.
BCM controls front wiper LO, HI, and INT (intermittent) operation.
IPDM E/R operates wiper motor according to CAN communication signals from the BCM.
Power is supplied at all times
through 50A fusible link (letter f , located in the fuse and fusible link box)
WW-3
2005 Maxima
to BCM terminal 52
INTERMITTENT OPERATION
Wiper intermittent operation delay interval is determined from the combination of the intermittent wiper dial
position inputs and vehicle speed. During each intermittent operation delay interval, the BCM sends a front
wiper request signal to the IPDM E/R to operate the wipers.
When the ignition switch is in ON or START position, and the front wiper switch is turned to intermittent position, the BCM detects a front wiper (intermittent) ON signal by BCM wiper switch reading function.
BCM then sends front wiper (intermittent) request signal over CAN communication lines
BCM calculates operation interval from wiper dial position and vehicle speed signal received from unified
meter and A/C amp. through CAN communications.
Revision: April 2008
WW-4
2005 Maxima
WASHER OPERATION
When wiper switch is in front wiper washer position, BCM detects front wiper washer signal by BCM wiper
switch reading function. Refer to BCS-3, "COMBINATION SWITCH READING FUNCTION" .
G
When the ignition switch is in ON or START position, power is supplied
MIST OPERATION
When the wiper switch is temporarily placed in the mist position, wiper low speed operation cycles once and
then stops.
For additional information about wiper operation under this condition, refer to WW-4, "LOW SPEED WIPER
OPERATION" .
If the switch is held in the mist position, low speed operation continues.
FAIL-SAFE FUNCTION
BCM includes fail-safe function to prevent malfunction of electrical components controlled by CAN communications if a malfunction in CAN communications occurs.
BCM uses CAN communications to stop output of electrical components it controls.
Until ignition switch is turned off, front wiper remains in same status as just before fail-safe control was initiated. (If wiper was in low speed operation just before fail-safe, it continues low speed operation until ignition
switch is turned OFF.)
When fail-safe status is initiated, BCM remains in standby until normal signals are received.
When normal signals are received, fail-safe status is canceled.
EKS0094K
WW-5
2005 Maxima
EKS0094L
WKWA1638E
WW-6
2005 Maxima
WW
WKWA1639E
WW-7
2005 Maxima
EKS0094M
Measuring condition
Terminal
No.
Wire
color
Signal name
Ignition
switch
ON
Operation or condition
SKIA5291E
R/Y
ON
SKIA5292E
R/G
ON
SKIA5291E
R/B
BR/R
ON
SKIA5292E
32
BR
ON
SKIA5291E
33
G/Y
ON
SKIA5292E
34
L/B
ON
SKIA5291E
WW-8
2005 Maxima
Wire
color
Signal name
35
G/B
Ignition
switch
ON
36
G/W
Operation or condition
SKIA5292E
38
R/W
ON
Battery voltage
39
CAN-H
40
CAN-L
52
Ground
ON
0V
55
W/B
Battery power
OFF
Battery voltage
21
ON
Wiper switch
31
L/B
ON
Wiper switch
32
L/Y
ON
38
Ground
44
R/W
48
Signal name
Ignition
switch
OFF
0V
LO
Battery voltage
OFF
0V
HI
Battery voltage
Operation or condition
Wiper operating
Battery voltage
Wiper stopped
0V
ON
0V
ON
Battery voltage
CAN-H
49
CAN-L
60
Ground
ON
0V
Work Flow
1.
2.
3.
4.
5.
6.
EKS0094N
Measuring condition
Terminal
No.
WW
L
EKS0094O
WW-9
2005 Maxima
EKS0094P
1. CHECK FUSE
Check if wiper and washer fuse is blown.
Unit
Power source
Fuse No.
Ignition ON or START
47
Battery
39
Ignition ON or START
Battery
BCM
OK or NG
OK
>> GO TO 2.
NG
>> If fuse is blown, be sure to eliminate cause of blown fuse before installing new fuse. Refer to PG4, "POWER SUPPLY ROUTING CIRCUIT" .
(+)
()
Connector
Terminal
(wire color)
M18
38 (R/W)
M19
55 (W/B)
Ground
OFF
ON
0V
Battery voltage
Battery voltage
Battery voltage
OK or NG
OK
>> GO TO 3.
NG
>> Check harness for open or short between BCM and fuse.
WKIA0401E
Terminal
(wire color)
M19
52 (B)
()
Ignition switch
condition
Continuity
Ground
OFF
Yes
OK or NG
OK
>> Inspection End.
NG
>> Repair/replace BCM ground circuit.
WKIA2955E
WW-10
2005 Maxima
EKS0094Q
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
BCM diagnostic
test item
Diagnostic mode
Description
B
WORK SUPPORT
DATA MONITOR
ACTIVE TEST
Inspection by part
SELF-DIAG RESULTS
CAN DIAG SUPPORT MNTR
ECU PART NUMBER
CONFIGURATION
CONSULT-II OPERATION
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carries out CAN communication.
1. With the ignition switch OFF, connect CONSULT-II and CONSULT-II CONVERTER to the data link connector, then turn the
ignition switch ON.
BBIA0002E
2.
M
BCIA0029E
3.
BCIA0030E
WW-11
2005 Maxima
LKIA0183E
DATA MONITOR
Operation Procedure
1.
2.
3.
ALL SIGNALS
4.
5.
6.
Touch "START".
When "SELECTION FROM MENU" is selected, touch items to be monitored. When "ALL SIGNALS" is
selected, all the items will be monitored.
Touch "RECORD" while monitoring to record the status of the item being monitored. To stop recording,
touch "STOP".
Contents
IGN ON SW
"ON/OFF"
Displays "IGN Position (ON)/OFF, ACC Position (OFF)" status as judged from ignition switch signal.
IGN SW CAN
"ON/OFF"
Displays "IGN switch ON (ON)/Other OFF or ACC (OFF)" status as judged from CAN communications.
FR WIPER HI
"ON/OFF"
Displays "Front Wiper HI (ON)/Other (OFF)" status as judged from wiper switch signal.
FR WIPER LOW
"ON/OFF"
Displays "Front Wiper LOW (ON)/Other (OFF)" status as judged from wiper switch signal.
FR WIPER INT
"ON/OFF"
Displays "Front Wiper INT (ON)/Other (OFF)" status as judged from wiper switch signal.
FR WASHER SW
"ON/OFF"
Displays "Front Washer Switch (ON)/Other (OFF)" status as judged from wiper switch signal.
(1 - 7)
Displays intermittent operation dial position setting (1 - 7) as judged from wiper switch signal.
INT VOLUME
FR WIPER STOP
"ON/OFF"
Displays "Stopped (ON)/Operating (OFF)" status as judged from the auto-stop signal.
VEHICLE SPEED
"ON/OFF"
Displays "Driving (ON)/Stopped (OFF)" status as judged from vehicle speed signal.
ACTIVE TEST
Operation Procedure
1.
2.
3.
4.
Display on CONSULT-II
screen
Description
FR WIPER (HI)
FR WIPER (LO)
FR WIPER (INT)
WW-12
2005 Maxima
EKS0094R
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
IPDM E/R diagnostic Mode
SELF-DIAG RESULTS
DATA MONITOR
Description
Displays IPDM E/R self-diagnosis results.
ACTIVE TEST
CONSULT-II OPERATION
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carries out CAN communication.
1. With the ignition switch OFF, connect CONSULT-II and CONSULT-II CONVERTER to the data link connector, then turn the
ignition switch ON.
BBIA0002E
2.
WW
BCIA0029E
3.
BCIA0030E
WW-13
2005 Maxima
BCIA0031E
DATA MONITOR
Operation Procedure
1.
2.
ALL SIGNALS
MAIN SIGNALS
3.
4.
5.
Touch "START".
When "SELECTION FROM MENU" is selected, touch items to be monitored. When "ALL SIGNALS" is
selected, all the items will be monitored. When "MAIN SIGNALS" is selected, predetermined items are
monitored.
Touch "RECORD" while monitoring to record the status of the item being monitored. To stop recording,
touch "STOP".
CONSULT-II
screen display
Display or unit
ALL
SIGNALS
MAIN
SIGNALS
SELECTION
FROM MENU
Description
FR WIP REQ
STOP/1LO/LO/HI
ACT P/STOP P
Wiper protection
WIP PROT
OFF/LS/HS/BLOCK
Item name
Front wiper
request
NOTE:
Perform monitoring of IPDM E/R data with the ignition switch ON. When the ignition switch is at ACC, the display may not be correct.
ACTIVE TEST
Operation Procedure
1.
2.
3.
CONSULT-II
screen display
FRONT WIPER
Description
With a certain operation (OFF, HI, LO) front wiper relays can be operated.
WW-14
2005 Maxima
EKS0094S
With CONSULT-II
Select "IPDM E/R" with CONSULT-II, and select "ACTIVE
TEST" on "SELECT DIAG MODE" screen.
2. Select "FRONT WIPER" on "SELECT TEST ITEM" screen.
1.
Without CONSULT-II
1. Turn on front wipers using auto active test. Refer to PG-21,
"Auto Active Test" .
2. Confirm front wiper operation.
OK or NG
OK
>> GO TO 4.
NG
>> GO TO 2.
E
SKIA3486E
Connector
Terminal
(wire color)
Connector
31 (L/B)
E122
21 (L)
Terminal
(wire color)
Continuity
H (L/B)
E23
32 (L/Y)
L (L)
Yes
P (L/Y)
WKIA3044E
4.
WW
IPDM E/R
(+)
()
Connector
Terminal
(wire color)
E121
60 (B)
E124
38 (B)
Continuity
L
Ground
Yes
M
WKIA0403E
5.
Terminal
(wire color)
E23
E (B)
Continuity
Ground
Yes
OK or NG
OK
>> Connect connectors. GO TO 3.
NG
>> Check for open circuit in harness between front wiper
motor and ground.
WW-15
WKIA3045E
2005 Maxima
1.
Without CONSULT-II
Turn on front wipers using auto active test. Refer to PG-21,
"Auto Active Test" .
SKIA3486E
When front wiper relay, and front wiper high relay are operating,
check voltage between IPDM E/R terminals and ground.
IPDM E/R
(+)
Connector
()
Voltage
(Approx.)
E122
Condition
31 (L/B)
32 (L/Y)
Ground
Stopped
0V
LO operation
Battery voltage
Stopped
0V
HI operation
Battery voltage
LO operation
Battery voltage
Stopped
0V
WKIA0404E
OK or NG
OK
>> Replace wiper motor. Refer to WW-23, "Removal and Installation of Wiper Motor and Linkage" .
NG
>> Replace IPDM E/R. Refer to PG-27, "Removal and Installation of IPDM E/R" .
WW-16
2005 Maxima
5. BCM INSPECTION
D
WKIA1018E
EKS00FQ6
I
SKIA5301E
2. CHECK IPDM E/R AND FRONT WIPER MOTOR AUTO STOP CIRCUITS
1.
2.
3.
WW
Connector
Terminal
(wire color)
Connector
Terminal
(wire color)
Continuity
E122
32 (L/Y)
E23
P (L/Y)
Yes
WKIA3046E
4.
E23
E (B)
Continuity
Ground
Yes
OK or NG
OK
>> Connect connectors. GO TO 3.
NG
>> Check for short circuit or open circuit in harness
between IPDM E/R and front wiper motor.
Check for open circuit in harness between front wiper
motor and ground.
Revision: April 2008
WW-17
WKIA3045E
2005 Maxima
3. CHECK IPDM E/R TO FRONT WIPER MOTOR AUTO STOP CIRCUIT VOLTAGE
1.
2.
(+)
Connector
Terminal
(wire color)
E122
32 (L/Y)
Ground
Condition
Voltage
(Approx.)
Wiper operating
Battery
voltage
Wiper stopped
0V
WKIA0407E
OK or NG
OK
>> Replace IPDM E/R. Refer to PG-27, "Removal and Installation of IPDM E/R" .
NG
>> Replace front wiper motor. Refer to WW-23, "Removal and Installation of Wiper Motor and Linkage" .
EKS00FQ7
WKIA1018E
EKS00FQ8
WW-18
SKIA3486E
2005 Maxima
Connector
Terminal
(wire color)
Connector
Terminal
(wire color)
Continuity
E122
31 (L/B)
E23
H (L/B)
Yes
OK or NG
OK
>> Connect connectors. GO TO 3.
NG
>> Check for short circuit or open circuit in harness
between IPDM E/R and front wiper motor.
WKIA3047E
With CONSULT-II
Select "IPDM E/R" with CONSULT-II, and select "ACTIVE
TEST" on "SELECT DIAG MODE" screen.
2. Select "FRONT WIPER" on "SELECT TEST ITEM" screen.
3. Select "HI" on "ACTIVE TEST" screen.
1.
Without CONSULT-II
1. Turn on front wipers using auto active test. Refer to PG-21,
"Auto Active Test" .
J
SKIA3486E
WW
IPDM E/R
(+)
()
Connector
Terminal
(wire color)
E122
31 (L/B)
Connector
Terminal
(wire color)
E124
38 (B)
E121
60 (B)
Battery
voltage
OK or NG
OK
>> Replace wiper motor. Refer to WW-23, "Removal and
Installation of Wiper Motor and Linkage" .
NG
>> Replace IPDM E/R. Refer to PG-27, "Removal and Installation of IPDM E/R" .
Voltage
(Approx.)
WW-19
WKIA0409E
2005 Maxima
WKIA1018E
EKS00FQ9
WKIA1018E
EKS00FQA
WKIA1018E
EKS00FQB
WKIA1018E
WW-20
2005 Maxima
EKS00FQC
CAUTION:
When auto stop signal has not varied for 10 seconds or longer while IPDM E/R is operating front
wipers, IPDM E/R considers front wipers locked and stops wiper output, which causes this symptom.
This status can be checked by using IPDM E/R "DATA MONITOR". Under this condition, "WIP
PROT" reads "BLOCK".
With CONSULT-II
Select "IPDM E/R" with CONSULT-II. With "DATA MONITOR", confirm that "WIP AUTO STOP" changes from "ACT P" to "STOP P"
according to wiper operation.
Without CONSULT-II
GO TO 2.
OK or NG
OK
>> Replace IPDM E/R. Refer to PG-27, "Removal and
Installation of IPDM E/R" .
NG
>> GO TO 2.
G
SKIA5301E
1.
2.
3.
Terminal
(wire color)
Connector
Terminal
(wire color)
Continuity
Connector
E122
32 (L/Y)
E23
P (L/Y)
Yes
WW
L
WKIA3046E
4.
E122
32 (L/Y)
Continuity
Ground
No
OK or NG
OK
>> Connect connectors. GO TO 3.
NG
>> Repair harness or connector.
LKIA0321E
WW-21
2005 Maxima
()
Connector
Terminal
(wire color)
E122
32 (L/Y)
Condition
Voltage
(Approx.)
Wiper operating
Battery
voltage
Wiper stopped
0V
Ground
WKIA0407E
OK or NG
OK
>> Replace IPDM E/R. Refer to PG-27, "Removal and Installation of IPDM E/R" .
NG
>> Replace front wiper motor. Refer to WW-23, "Removal and Installation of Wiper Motor and Linkage" .
Removal and Installation of Front Wiper Arms, Adjustment of Wiper Arms Stop
Location
EKS0094T
1.
2.
3.
4.
SEL543TA
Before reinstalling wiper arm, clean up the pivot area as illustrated. This will reduce possibility of wiper arm looseness.
Tighten wiper arm nuts to specified torque.
Front wiper
arm nuts
SEL024J
WW-22
2005 Maxima
EKS0094U
F
LKIA0130E
1.
2.
Wiper link
3.
Wiper frame
REMOVAL
1.
2.
3.
4.
5.
6.
7.
Operate the wiper motor and stop it at the auto stop position.
Remove wiper arms from the vehicle. Refer to WW-22, "Removal and Installation of Front Wiper Arms,
Adjustment of Wiper Arms Stop Location" .
Remove the cowl top cover. Refer to EI-19, "Removal and Installation" .
Disconnect wiper motor connector.
Remove bracket and wiper motor assembly.
Remove wiper link from wiper frame.
Remove wiper motor from wiper frame.
WW
WKIA0067E
INSTALLATION
CAUTION:
Check the grease conditions of the motor arm and wiper link joint(s). Apply grease if necessary.
1. Connect wiper motor to connector. Turn the wiper switch ON to operate wiper motor, then turn the wiper
switch OFF (auto stop).
2. Disconnect wiper motor connector.
3. Install wiper motor to bracket and wiper link, and install assembly to the vehicle.
Wiper motor assembly bolts : 3.8 - 5.1 Nm (0.39 - 0.52 kg-m, 33.9 - 45.1 in-lb)
4.
5.
6.
Connect wiper motor connector. Turn the wiper switch ON to operate the wiper motor, then turn wiper
switch OFF (auto stop).
Install cowl top cover. Refer to EI-19, "Removal and Installation" .
Install wiper arms. Refer to WW-22, "Removal and Installation of Front Wiper Arms, Adjustment of Wiper
Arms Stop Location" .
WW-23
2005 Maxima
EKS0094V
PKIA2552E
EKS0094W
LKIA0184E
EKS0094X
1.
2.
3.
WKIA0071E
EKS0094Y
1.
2.
WW-24
LKIA0185E
2005 Maxima
3.9 - 5.0 Nm
(0.40 - 0.50 kg-m, 34 - 45 in-lb)
B
EKS0094Z
1.
2.
3.
F
LKIA0186E
WW
WW-25
2005 Maxima
POWER SOCKET
POWER SOCKET
Wiring Diagram P/SCKT
PFP:253A2
EKS00952
WKWA1637E
WW-26
2005 Maxima
POWER SOCKET
Removal and Installation of Power Sockets
EKS00951
REMOVAL
NOTE:
Removal and Installation is common for all power sockets.
1. Remove inner socket from the ring, while pressing the hook on
the ring out from square hole.
2. Disconnect power socket connector.
3. Remove ring from power socket finisher while pressing pawls.
WKIA1035E
INSTALLATION
Installation is in the reverse order of removal.
WW
WW-27
2005 Maxima
HORN
HORN
Wiring Diagram HORN
PFP:25610
EKS00954
WKWA1640E
WW-28
2005 Maxima
HORN
Removal and Installation
EKS00955
D
WKIA0077E
J
WKIA0078E
WW-29
2005 Maxima
HORN
WW-30
2005 Maxima