Professional Documents
Culture Documents
Video Cassette
Recorder
Operating Instructions
PAL
SLV-SE830D/E
SLV-SE737E
SLV-SX737D
SLV-SE730D/E
SLV-SX730D/E
SLV-SE630D/E
SLV-SE230D
2003 Sony Corporation
WARNING
To prevent fire or shock hazard, do not expose the
unit to rain or moisture.
To avoid electrical shock, do not open the cabinet.
Refer servicing to qualified personnel only.
Mains lead must only be changed at a qualified
service shop.
Precautions
Safety
This unit operates on 220 240 V AC, 50 Hz.
Check that the units operating voltage is
identical with your local power supply.
If anything falls into the cabinet, unplug the unit
and have it checked by qualified personnel before
operating it any further.
The unit is not disconnected from the mains as
long as it is connected to the mains, even if the
unit itself has been turned off.
Unplug the unit from the wall outlet if you do not
intend to use it for an extended period of time. To
disconnect the cord, pull it out by the plug, never
by the cord.
To prevent fire or shock hazard, do not place
objects filled with liquids, such as vases, on the
apparatus.
Installing
Do not install this equipment in a confined space
such as a book or similar unit.
Allow adequate air circulation to prevent internal
heat buildup.
Do not place the unit on surfaces (rugs, blankets,
etc.) or near materials (curtains, draperies) that
may block the ventilation slots.
Do not install the unit near heat sources such as
radiators or air ducts, or in a place subject to
direct sunlight, excessive dust, mechanical
vibration or shock.
Do not install the unit in an inclined position. It is
designed to be operated in a horizontal position
only.
Keep the unit and cassettes away from equipment
with strong magnets, such as microwave ovens or
large loudspeakers.
Do not place heavy objects on the unit.
If the unit is brought directly from a cold to a
warm location, moisture may condense inside the
VCR and cause damage to the video head and
tape. When you first install the unit, or when you
move it from a cold to a warm location, wait for
about three hours before operating the unit.
2 WARNING
Caution
Television programmes, films, video tapes and other
materials may be copyrighted. Unauthorized
recording of such material may be contrary to the
provisions of the copyright laws. Also, use of this
recorder with cable television transmission may
require authorization from the cable television
transmitter and/or programme owner.
Compatible colour systems
This VCR is designed to record using the PAL (B/
G) colour system and play back using the PAL (B/
G) colour system. Recording of video sources based
on other colour systems cannot be guaranteed.
SHOWVIEW is a registered trademark of Gemstar
Development Corporation. The SHOWVIEW system
is manufactured under license from Gemstar
Development Corporation.
Getting Started
4 Index to parts and controls
11 Step 1 : Unpacking
12 Step 2 : Setting up the remote
commander
16 Step 3 : Connecting the VCR
20 Step 4 : Setting up the VCR with
the Auto Set Up function
23 Setting the clock
25 Downloading the TV tuners preset
data (not available on SLVSE630D/E and SE230D)
26 Selecting a language
27 Presetting channels
30 Changing/disabling programme
positions
35 Setting the PAY-TV/Canal Plus
decoder
Basic Operations
38 Playing a tape
40 Recording TV programmes
44 Recording TV programmes using
the Dial Timer (SLV-SE830D/E
only)
49 Recording TV programmes using
the ShowView system (not
available on SLV-SE630D/E)
53 Recording TV programmes using
the timer
Additional Operations
56 Playing/searching at various speeds
58 Setting the recording duration time
59 Checking/changing/cancelling
timer settings
61 Recording stereo and bilingual
programmes (not available on SLVSE230D)
64 Searching using the index function
(not available on SLV-SE230D)
66 Adjusting the picture
67 Reducing the VCRs power
consumption
68 Changing menu options
Getting Started
Table of contents
Editing
70 Connecting to a VCR or stereo
system
72 Basic editing
73 Audio dubbing (SLV-SE830D/E
only)
Additional Information
74 Troubleshooting
78 Specifications
79 Index
Back Cover
Quick Start Guide
Table of contents
Getting Started
Front panel
For SLV-SE830D/E
C Tape compartment
D A (eject) button (38)
E m (rewind) button (38) (56)
F Shuttle ring (56)
G H (play) button* (38) (56)
H M (fast-forward) button (38) (56)
I JOG button (56)
J REC z (record) button (41) (58)
(72)
K x (stop) button* (22) (38) (72) (73)
continued
Index to parts and controls
For SLV-SE230D
Display window
8 7
A Tape indicator
E TV indicator (43)
C Time counter/clock/line/programme
position indicator (38) (40) (72)
Getting Started
A Tape indicator
B Time counter/clock/line/programme
position indicator (38) (40) (72)
G Playback indicator
* not available on SLV-SE230D
continued
Index to parts and controls
Rear panel
For SLV-SE830D/E, SE737E, SX737D, SE730D/E, SX730D/E and
SE630D/E
For SLV-SE230D
* SLV-SE830D/E
*2 SLV-SE737E, SX737D, SE730D/E,
SX730D/E, SE630D/E and SE230D
*3 not available on SLV-SE630D/E
Remote commander
Getting Started
continued
Index to parts and controls
Getting Started
Step 1 : Unpacking
Check that you have received the following items with the VCR:
Remote commander
Aerial cable
Unpacking
11
Remote sensor
[TV] /
[VIDEO]
To operate
the VCR
a Sony TV
AUDIO MONITOR
DISPLAY
t TV/VIDEO
Getting Started
?/1
Programme
number
buttons
/
PROG +//
c C
2 +/
a
FASTEXT buttons
TV control buttons
To
Press
?/1
t TV/VIDEO
2 +/
a (TV)
continued
Setting up the remote commander
13
To
Press
/ (Teletext)
Switch to Teletext*
Select the sound*
AUDIO MONITOR
Use FASTEXT*1
FASTEXT buttons
DISPLAY
c C
(wide)
Notes
With normal use, the batteries should last about three to six months.
If you do not use the remote commander for an extended period of time, remove
the batteries to avoid possible damage from battery leakage.
Do not use a new battery together with an old one.
Do not use different types of batteries together.
Some buttons may not work with certain Sony TVs.
*1 SLV-SE830D/E, SE737E and SX737D only
*2 not available on SLV-SE230D
Controlling other TVs with the remote commander (SLVSE830D/E, SE737E and SX737D only)
The remote commander is preprogrammed to control non-Sony TVs. If your
TV is listed in the following table, set the appropriate manufacturers code
number.
To switch to wide mode, see the footnotes below this table for the applicable
code numbers.
Manufacturer
Code number
Manufacturer
Code number
Sony
01* , 02
Panasonic
17*1, 49
Akai
68
Philips
Ferguson
52
Saba
12, 13
Samsung
22, 23
Grundig
10* , 11*
Hitachi
24
Sanyo
25
JVC
33
Sharp
29
Loewe
45
Telefunken
36
Mivar
09, 70
Thomson
43*2
NEC
66
Toshiba
38
Nokia
Getting Started
*1 Press
(wide) to switch the wide picture mode on or off.
*2 Press
(wide), then press 2 +/ to select the wide picture mode you want.
*3 Press
(wide). The menu appears on the TV screen. Then, press M/m/</, to
select the wide picture you want and press OK.
Tip
When you set your TVs code number correctly while the TV is turned on, the TV
turns off automatically.
Notes
If you enter a new code number, the code number previously entered will be
erased.
If the TV uses a different remote control system from the one programmed to work
with the VCR, you cannot control your TV with the remote commander.
When you replace the batteries of the remote commander, the code number may
change. Set the appropriate code number every time you replace the batteries.
15
Mains lead
AERIAL IN
to mains
Connect
of the VCR and the aerial
input of your TV using the supplied
aerial cable.
AERIAL IN
Scart
(EURO-AV)
: Signal flow
Mains lead
Getting Started
to mains
Connect
of the VCR and the
aerial input of your TV using the
supplied aerial cable.
continued
Connecting the VCR
17
Additional connections
Getting Started
To a satellite or digital
tuner with Line Through
Using the Line Through
function, you can watch
programmes from a satellite
or digital tuner connected to
this VCR on the TV even
when the VCR is turned off.
When you turn on the
satellite or digital tuner, this
VCR automatically sends the
signal from the satellite or
digital tuner to the TV
without turning itself on.
LINE-3 (DEC/EXT)*1 or
LINE-2 (DEC/EXT)*2
LINE
OUT
To watch a programme, turn on the satellite or digital tuner and the TV.
Notes
The Line Through function will not operate properly if POWER SAVE in the
USER SET menu is set to ECO2. Set POWER SAVE to OFF or ECO1 to ensure
proper operation (see page 67).
You cannot watch programmes on the TV while recording unless you are recording
a satellite or digital programme.
This function may not work with some types of satellite or digital tuners.
When the VCR is turned off, set the TV to the video channel.
*1 SLV-SE830D/E
*2 SLV-SE737E, SX737D, SE730D/E, SX730D/E, SE630D/E and SE230D
19
GB
ES
NL
FI
S E L E CT
SET
DE
IT
SE
GR
:
: OK
FR
PT
DK
TR
EXIT
: M E NU
Abbreviation
Language
Abbreviation
Language
GB
English
SE
Swedish
ES
Spanish
GR
Greek
NL
Dutch
FR
French
FI
Finnish
PT
Portuguese
DE
German
DK
Danish
IT
Italian
TR
Turkish
Press OK.
COUNTRY S E L E CTI ON
A
B
DK
FI N
D
NL
S E L E CT
SET
5
OK
I
N
P
E
S
CH
:
: OK
TR
GR
HU
PL
CZ
OTHE RS
EXIT
: M E NU
Abbreviation Country
Abbreviation Country
Austria
Spain
Belgium
Sweden
DK
Denmark
CH
Switzerland
FIN
Finland
TR
Turkey
Germany
GR
Greece
NL
Netherlands
HU
Hungary
Italy
PL
Poland
Norway
CZ
Czech
Portugal
Getting Started
OK
A UTO S E T UP
PLEASE WAIT
40%
EXIT
: M E NU
The VCR starts searching for all of the receivable channels and
presets them (in the appropriate order for your local area).
If you want to change the order of the channels or disable unwanted
programme positions, see Changing/disabling programme
positions on page 30.
After the search or download is complete, the current time appears
for any stations that transmit a time signal. If the time does not
appear, set the clock manually. See Setting the clock on page 23.
For SLV-SE630D/E
The clock setting menu appears. See Setting the clock on page 23.
continued
Setting up the VCR with the Auto Set Up function
21
You must set the time and date on the VCR to use the timer features properly.
The Auto Clock Set function* works only if a station in your area is broadcasting a
time signal.
Getting Started
MENU
12 :00
1 / JAN / 2 0 0 3
WED
A UTO CL OCK
: ON
OK
S E L E CT
E ND
:
: OK
SET
EXIT
:
: M E NU
18 :00
1 / JAN / 2 0 0 3
WED
A UTO CL OCK
S E L E CT
E ND
:
: OK
: ON
SET
EXIT
:
: M E NU
18 :30
1 / JAN / 2 0 0 3
WED
A UTO CL OCK
S E L E CT
E ND
4
OK
:
: OK
18 :30
SET
EXIT
:
: M E NU
2 8 / SEP / 2 0 0 3
S UN
A UTO CL OCK
S E L E CT
E ND
: ON
:
: OK
: ON
SET
EXIT
:
: M E NU
continued
Setting the clock
23
5
OK
18 :30
2 8 / SEP / 2 0 0 3
S UN
A UTO CL OCK
S E L E CT
E ND
:
: OK
: ON
SET
EXIT
:
: M E NU
MENU
Tips
If you set AUTO CLOCK* to ON, the Auto Clock Set function is activated
whenever the VCR is turned off. The time is adjusted automatically by making
reference to the time signal from the station.
To change the digits while setting, press < to return to the item to be changed, and
select the digits by pressing M/m.
* not available on SLV-SE630D/E
Getting Started
MENU
OK
A UTO S E T UP
M A NUA L S E T UP
S M A RTL I NK
V CR OUTP UT CH
S E L E CT
E ND
:
: OK
:32
SET
EXIT
:
: M E NU
S M A RTL I NK
OK
TV CH DOW NL OA D
TV DI RE CT RE CORD : OFF
S E L E CT
E ND
3
OK
:
: OK
SET
EXIT
:
: M E NU
TV CH DOW NL OA D
PLEASE WAIT
40%
E ND
: OK
S TA RT:
E X I T : M E NU
Downloading the TV tuners preset data (not available on SLV-SE630D/E and SE230D)
25
Selecting a language
You can change the on-screen display language from the one you selected with the
Auto Set Up function.
Before you start
Turn on the VCR and the TV.
Set the TV to the video channel.
Refer to Index to parts and controls for button locations.
MENU
GB
ES
NL
FI
DE
IT
SE
GR
FR
PT
DK
TR
OK
S E L E CT
SET
:
: OK
EXIT
: M E NU
26 Selecting a language
If some channels could not be preset using the Auto Set Up function, you can preset
them manually.
Before you start
Getting Started
Presetting channels
MENU
A UTO S E T UP
M A NUA L S E T UP
S M A RTL I NK
V CR OUTP UT CH
:32
OK
S E L E CT
E ND
OK
SET
EXIT
:
: M E NU
TV S TA TI ON TA B L E
PR
1
2
3
4
5
CH
027
029
030
032
DE L E TE
:
: OK
NA M E
AAB
L MN
CDE
I J K
DE C
OFF
OFF
OFF
OFF
S W A P P I NG : OK
: CL E A R
E X I T : M E NU
M A NUA L TUNI NG
PR
CH
M FT
DE CODE R
NA M E
S E L E CT
E ND
:
: OK
:
:
:
:
:
OFF
SET
EXIT
:
: M E NU
continued
Presetting channels
27
M A NUA L TUNI NG
PR
CH
M FT
DE CODE R
NA M E
S E L E CT
E ND
SET
EXIT
:
: M E NU
M A NUA L TUNI NG
S E L E CT
E ND
5
033
OFF
:
: OK
PR
CH
M FT
DE CODE R
NA M E
OK
:
:
:
:
:
:
:
:
:
:
5
033
OFF
SET
EXIT
:
: OK
:
: M E NU
M A NUA L TUNI NG
PR
CH
M FT
DE CODE R
NA M E
S E L E CT
E ND
:
:
:
:
:
5
033
OFF
O
:
: OK
SET
EXIT
:
: M E NU
MENU
28 Presetting channels
Tips
To set the programme position for the decoder, see Setting the PAY-TV/Canal
Plus decoder on page 35.
The VCR must receive channel information for station names to appear
automatically.*
Getting Started
Note
When adjusting MFT, the menu may become difficult to read due to interference
from the picture being received.
* not available on SLV-SE630D/E
Presetting channels
29
MENU
A UTO S E T UP
M A NUA L S E T UP
S M A RTL I NK
V CR OUTP UT CH
:32
OK
S E L E CT
E ND
OK
CH
027
029
030
032
:
: M E NU
NA M E
AAB
L MN
CDE
I J K
DE C
OFF
OFF
OFF
OFF
S W A P P I NG : OK
E X I T : M E NU
: CL E A R
TV S TA TI ON TA B L E
PR
1
2
3
4
5
CH
027
029
030
032
DE L E TE
SET
EXIT
TV S TA TI ON TA B L E
PR
1
2
3
4
5
DE L E TE
:
: OK
NA M E
AAB
L MN
CDE
I J K
DE C
OFF
OFF
OFF
OFF
S W A P P I NG : OK
E X I T : M E NU
: CL E A R
TV S TA TI ON TA B L E
PR
1
2
3
4
5
CH
027
NA M E
AAB
DE C
OFF
030
032
029
CDE
I J K
L MN
OFF
OFF
OFF
S W A P P I NG : OK
E X I T : M E NU
Getting Started
6
7
MENU
A UTO S E T UP
M A NUA L S E T UP
S M A RTL I NK
V CR OUTP UT CH
:32
OK
S E L E CT
E ND
:
: OK
SET
EXIT
:
: M E NU
continued
Changing/disabling programme positions
31
TV S TA TI ON TA B L E
PR
1
2
3
4
5
CH
027
029
030
032
DE L E TE
CLEAR
CH
027
029
030
032
NA M E
AAB
L MN
CDE
I J K
DE C
OFF
OFF
OFF
OFF
S W A P P I NG : OK
E X I T : M E NU
: CL E A R
TV S TA TI ON TA B L E
PR
1
2
3
4
5
CH
027
NA M E
AAB
DE C
OFF
030
032
CDE
I J K
OFF
OFF
DE L E TE
S W A P P I NG : OK
: CL E A R
E X I T : M E NU
Press CLEAR.
The selected row will be cleared as
shown on the right.
DE C
OFF
OFF
OFF
OFF
TV S TA TI ON TA B L E
PR
1
2
3
4
5
DE L E TE
NA M E
AAB
L MN
CDE
I J K
S W A P P I NG : OK
E X I T : M E NU
: CL E A R
Repeat steps 3 and 4 for any other programme positions you want to
disable.
MENU
Note
Be sure to select the programme position you want to disable correctly. If you
disable a programme position by mistake, you need to reset that channel manually.
MENU
OK
A UTO S E T UP
M A NUA L S E T UP
S M A RTL I NK
V CR OUTP UT CH
S E L E CT
E ND
OK
:
: M E NU
NA M E
AAB
L MN
CDE
I J K
DE C
OFF
OFF
OFF
OFF
OFF
S W A P P I NG : OK
E X I T : M E NU
: CL E A R
M A NUA L TUNI NG
PR
CH
M FT
DE CODE R
NA M E
S E L E CT
E ND
SET
EXIT
CH
027
029
030
032
033
DE L E TE
:32
TV S TA TI ON TA B L E
PR
1
2
3
4
5
OK
:
: OK
Getting Started
You can change or enter the station names (up to 4 characters). The VCR must
receive channel information for station names to appear automatically*.
:
:
:
:
:
5
033
OFF
SET
EXIT
:
: OK
:
: M E NU
M A NUA L TUNI NG
PR
CH
M FT
DE CODE R
NA M E
S E L E CT
E ND
:
: OK
:
:
:
:
:
5
033
OFF
SET
EXIT
:
: M E NU
continued
Changing/disabling programme positions
33
M A NUA L TUNI NG
PR
CH
M FT
DE CODE R
NA M E
S E L E CT
E ND
:
:
:
:
:
5
033
OFF
O
:
: OK
SET
EXIT
:
: M E NU
MENU
You can watch or record PAY-TV/Canal Plus programmes if you connect a decoder
(not supplied) to the VCR.
Connecting a decoder
Scart cable
(not supplied)
Getting Started
PAY-TV/Canal
Plus decoder
Scart
(EURO-AV)
LINE-3 (DEC/EXT)*1 or
LINE-2 (DEC/EXT)*2
continued
Setting the PAY-TV/Canal Plus decoder
35
MENU
A UTO S E T UP
M A NUA L S E T UP
S M A RTL I NK
V CR OUTP UT CH
:32
OK
S E L E CT
E ND
OK
:
: M E NU
DE C
OFF
OFF
OFF
OFF
OFF
S W A P P I NG : OK
E X I T : M E NU
: CL E A R
M A NUA L TUNI NG
PR
CH
M FT
DE CODE R
NA M E
S E L E CT
E ND
NA M E
AAB
L MN
CDE
I J K
CH
027
029
030
032
033
DE L E TE
SET
EXIT
TV S TA TI ON TA B L E
PR
1
2
3
4
5
OK
:
: OK
:
:
:
:
:
5
033
OFF
SET
EXIT
:
: OK
:
: M E NU
PR
CH
M FT
DE CODE R
NA M E
S E L E CT
E ND
5
033
OFF
SET
EXIT
:
: OK
:
: M E NU
M A NUA L TUNI NG
PR
CH
M FT
DE CODE R
NA M E
S E L E CT
E ND
:
:
:
:
:
:
: OK
:
:
:
:
:
5
033
ON
SET
EXIT
:
: M E NU
MENU
Notes
To superimpose subtitles while watching PAY-TV/Canal Plus programmes, make
both decoder-VCR and VCR-TV connections using 21-pin Scart cables that are
compatible with the RGB signals. You cannot record subtitles on the VCR.
When you watch PAY-TV/Canal Plus programmes through the RFU input of the
TV, press t TV/VIDEO so that the VIDEO indicator appears in the display
window.
Getting Started
*1 SLV-SE830D/E
*2 SLV-SE737E, SX737D, SE730D/E, SX730D/E, SE630D/E and SE230D
37
Basic Operations
Playing a tape
Before you start...
Refer to Index to parts and controls for button locations.
Insert a tape.
Press H (play).
OK
Additional tasks
To
Press
Stop play
x (stop)
Pause play
X (pause)
X (pause) or H (play)
Z (eject)
Hour
SE630D/E, SE230D
Minute Second
Hour
Minute
DISPLAY.
Basic Operations
Notes
The counter resets to 0:00:00 or 00:00 whenever a tape is reinserted.
The counter stops counting when it comes to a portion with no recording.
Depending on your TV, the following may occur while playing an NTSC-recorded
tape:
The picture becomes black and white.
The picture shakes.
No picture appears on the TV screen.
Black streaks appear horizontally on the TV screen.
The colour density increases or decreases.
Tapes recorded in the LP mode cannot be played back on SLV-SE230D.
While setting the menu on the TV screen, buttons for playback on the remote
commander do not function.
1 Insert a tape.
If you insert a tape with its safety tab removed, the TV turns on and
switches to the video channel. Playback starts automatically.
Press H (play).
The TV turns on and switches to the video channel automatically.
Playback starts.
Tip
When there already is a tape in the VCR, press ?/1 to turn on the VCR first. When
you press H (play), the TV turns on, the TV is set to the video channel, and
playback starts automatically in one sequence.
Note
When you use the One Touch Play function, leave the TV on or in the standby
mode.
Playing a tape
39
Recording TV programmes
Before you start...
Refer to Index to parts and controls for button locations.
PROG
INPUT SELECT
SP / LP
40 Recording TV programmes
REC
Recording indicator
SE630D/E, SE230D
To stop recording
Press x (stop).
Basic Operations
Recording indicator
RE M A I N
0 : 00 : 22
1 : 46
Time counter
Remaining time
41
To save a recording
To prevent accidental erasure, break off the
safety tab as illustrated. To record on the
same tape again, cover the tab hole with
adhesive tape.
Safety tab
Tips
To select a programme position, you can use the programme number buttons on the
remote commander. For two-digit numbers, for example, press 2 and 3 to select
PR 23.
If you connect additional equipment to a LINE connector or jack, you can select
the input signal using the INPUT SELECT or PROG +/ buttons.
The
DISPLAY information appears on the TV screen indicating information
about the tape, but the information will not be recorded on the tape.
If you do not want to watch TV while recording, you can turn off the TV. When
using a decoder, make sure to leave it on.
Notes
The
DISPLAY information does not appear during still (pause) mode or slowmotion playback.
If a tape has portions recorded in both PAL and NTSC systems, the time counter
reading will not be correct. This discrepancy is due to the difference between the
counting cycles of the two video systems.
You cannot watch a PAY-TV/Canal Plus programme while recording another PAYTV/Canal Plus programme.
When you insert a non-standard commercially available tape, the remaining time
may not be correct.
The remaining time is intended for rough measurement only.
About 30 seconds after the tape begins playback, the tape remaining time will be
displayed.
* not available on SLV-SE230D
42 Recording TV programmes
Basic Operations
The TV indicator lights up and the VCR starts recording what you are
watching on the TV.
Notes
You cannot record what you are watching using this method when the VCR is in
the following modes; pause, timer standby, tuner preset, Auto Set Up, and
recording.
When the TV indicator is lit in the display window, do not turn off the TV nor
change the TV programme position. When the TV indicator is not lit, the VCR
continues recording the programme even if you change the TV programme
position on the TV.
To use the TV Direct Rec function, select SMARTLINK in the INSTALLATION
menu, then set TV DIRECT RECORD to ON.
Recording TV programmes
43
?/1
DIAL TIMER
PROGRAM +/ X
DIAL TIMER
Press
DIAL TIMER.
DIAL TIMER
Turn
DIAL TIMER
DIAL TIMER
Press
DIAL TIMER.
You can set the recording start time in 15 minute intervals or adjust
the time in one minute intervals by pressing the PROGRAM +/
buttons.
Basic Operations
Turn
PROGRAM
DIAL TIMER
DIAL TIMER
Press
DIAL TIMER.
Turn
You can set the recording stop time in 15 minute intervals or adjust
the time in one minute intervals by pressing the PROGRAM +/
buttons.
PROGRAM
continued
Recording TV programmes using the Dial Timer (SLV-SE830D/E only)
45
DIAL TIMER
DIAL TIMER
DIAL TIMER.
INPUT SELECT
Press
DIAL TIMER
Turn
Tips
To cancel a Dial Timer setting, press x (stop) on the VCR while you are making
the setting.
The programme is recorded in the current tape speed mode. To change the tape
speed, press SP/LP before you complete the setting in step 9.
To check, change, or cancel the programme setting, see Checking/changing/
cancelling timer settings on page 59.
Basic Operations
2
DIAL TIMER.
3 Press
MONTH appears in the display window.
and press
DIAL TIMER to set the month, and then the year.
4 Turn
After you set the year, CLOCK appears in the display window again.
5 Turn and press DIAL TIMER to set the hour and minute.
you have finished setting the time, press
DIAL TIMER to start
6 When
the clock.
Notes
If eight programmes have already been set using the ShowView system or the
TIMER PROGRAMMING menu, FULL appears in the display window for
about five seconds.
The
indicator flashes in the display window when you complete the setting in
step 9 with no tape inserted.
If you set the clock using the Auto Clock Set function and AUTO CLOCK is set to
ON, the clock will adjust itself to the incoming time signal regardless of
adjustments made with the Dial Timer. Be sure you have set the Auto Clock Set
correctly.
When the time is set incorrectly, ERROR appears in the display window in step
9. Set the timer again from step 1.
You cannot set the tape speed to AUTO using the Dial Timer. To select AUTO, set
the tape speed in the TIMER PROGRAMMING menu (see page 59).
continued
Recording TV programmes using the Dial Timer (SLV-SE830D/E only)
47
Check that the VCR clock is set to the correct time and date.
Insert a tape with its safety tab in place. Make sure the tape is longer than the total recording
time.
To record from a decoder, turn it on.
Turn on your TV and set it to the video channel.
Set TIMER METHOD to SHOWVIEW or VARIABLE in the EASY OPERATION menu
(see page 69).
Refer to Index to parts and controls for button locations.
Press
TIMER
OK
Basic Operations
TIMER.
TI M E R M E THOD
S TA NDA RD
S HOW V I E W
S E L E CT
SET
:
: OK
EXIT
: M E NU
S HOW V I E W
CODE
CODE : 0 9
SET
: OK
EXIT
: M E NU
continued
Recording TV programmes using the ShowView system (not available on SLV-SE630D/E)
49
CLEAR
S HOW V I E W
CODE
1234
CODE : 0 9
SET
: OK
EXIT
: M E NU
Press OK.
OK
INPUT SELECT
CLEAR
PR
35
DA Y
SA2
S TA RT
19 :00
:
:
:
:
:
S TOP
20 :0
:
:
:
:
:
SP
V/P
If appears in the PR
S E L E CT :
SET
:
E ND
: OK
E X I T : M E NU
(programme) column (this may
happen for local broadcasts), you
have to set the appropriate programme position manually.
Press M/m to select the desired programme position.
To record from a decoder or other source connected to one or
more of the LINE inputs, press INPUT SELECT to display the
connected line in the PR position.
You will only have to do this operation once for the referred
channel. The VCR will then store your setting.
If the information is incorrect, press CLEAR to cancel the setting.
MENU
PR
35
DA Y
SA2
S TA RT
19 :00
:
:
:
:
:
S TOP
20 :0
:
:
:
:
:
V/P
0
SP
ON
Basic Operations
Daily/weekly recording
In step 4 above, press m to select the recording pattern. Each time you press
m, the indication changes as shown below. Press M to change the indication
in reverse order.
To use the VPS/PDC function, set V/P to ON in step 4 above. You can also
use the VPS/PDC function for a source connected to one or more of the
LINE inputs.
To use the VCR after setting the timer
To use the VCR before a recording begins, just press ?/1. The indicator
turns off and the VCR switches on. Remember to press ?/1 to reset the VCR
to recording standby after using the VCR.
You can also do the following tasks while the VCR is recording:
continued
Recording TV programmes using the ShowView system (not available on SLV-SE630D/E)
51
TIMER
Press
TIMER.
For SLV-SE630D/E
The TIMER PROGRAMMING
menu appears on the TV screen.
OK
PR
DA Y
S E L E CT
E ND
S TA RT
:
:
:
:
:
:
:
: OK
S TOP
:
:
:
:
:
:
SET
EXIT
V/P
:
: M E NU
TI M E R M E THOD
S TA NDA RD
S HOW V I E W
S E L E CT
SET
Basic Operations
Check that the VCR clock is set to the correct time and date.
Insert a tape with its safety tab in place. Make sure the tape is longer than the total recording
time.
To record from a decoder, turn it on.
Turn on your TV and set it to the video channel.
Set TIMER METHOD*1 to STANDARD or VARIABLE in the EASY OPERATION menu
(see page 69).
Refer to Index to parts and controls for button locations.
PR
DA Y
S E L E CT
E ND
:
: OK
S TA RT
:
:
:
:
:
:
:
: OK
EXIT
: M E NU
S TOP
:
:
:
:
:
:
SET
EXIT
V/P
:
: M E NU
continued
Recording TV programmes using the timer
53
2
OK
INPUT SELECT
PR
35
DA Y
S E L E CT
E ND
S TA RT
:
:
:
:
:
:
:
: OK
S TOP
:
:
:
:
:
:
SET
EXIT
V/P
:
: M E NU
To record the same programme every day or the same day every
week, see Daily/weekly recording on page 54.
To use the VPS/PDC function*1, set V/P to ON. For details about
the VPS/PDC function, see Timer recording with VPS/PDC
signals on page 51.
To record from a decoder or other source connected to one or
more of the LINE inputs, press INPUT SELECT to display the
connected line in the PR position.
3
4
MENU
55
Additional Operations
Operation
* SLV-SE830D/E only
Shuttle ring
JOG
Slow motion
in reverse
Slow motion
Normal speed
in reverse
High speed in
reverse
Double speed
High speed
Additional Operations
Double speed
in reverse
Normal speed
(Initial speed)
Press JOG to enter the jog mode. The JOG button lights up. If you change
to the jog mode during any playback mode, playback pauses so you can see a
still picture. Each change in the shuttle ring position shifts the picture one
frame. To shift frames in reverse, turn the shuttle ring anticlockwise. The
frame shift speed depends on the speed you turn the shuttle ring.
To resume normal mode, press JOG again. The JOG button turns off.
Tip
Adjust the picture using the PROGRAM +/ buttons on the VCR if:
Streaks appear while playing in slow motion.
Bands appear at the top or bottom while pausing.
The picture shakes while pausing.
To set tracking to the centre position, press both buttons (+/) at the same time.
Notes
The sound is muted during these operations.
In the LP mode, noise may appear or there may be no colour.
If the playback mode mark does not appear on the TV screen, press
DISPLAY.
The picture may show noise when playing at high speed in reverse.
The picture returns to normal playback from slow motion in reverse in 30 seconds.
57
1:00
4:00
4:30
Normal recording
In LP mode
Each press advances the time as shown below.
0:30
1:00
8:00
9:00
Normal recording
The tape counter decreases minute by minute to 0:00, then the VCR stops
recording and turns off automatically.
To extend the duration
Press z REC repeatedly to set a new duration time.
To cancel the duration
Press z REC repeatedly until the indicator disappears and the VCR
returns to the normal recording mode.
To stop recording
To stop the VCR while recording, press x (stop).
Note
You cannot display the current tape time in the display window when setting the
recording duration time.
Checking/changing/cancelling timer
settings
Before you start
Turn on your TV and set it to the video channel.
Refer to Index to parts and controls for button locations.
DA Y
SA2
SA2
SA
S E L E CT
E ND
PR
35
29
30
DA Y
SA2
SA2
SA
S E L E CT
E ND
9
9
6
S TA RT
19 :00
21 :00
12 :00
:
:
:
:
: OK
9
9
6
S TA RT
19 :00
21 :00
12 :00
:
:
:
:
: OK
S TOP
20 :0
21 :3
13 :3
:
:
:
SET
EXIT
SP
ON
:
: M E NU
S TOP
20 :0
21 :3
13 :3
:
:
:
SET
EXIT
V/P
0
0
0
V/P
0
0
0
SP
ON
Additional Operations
:
: M E NU
change the setting, press </, to select the item you want to
4 To
change, then press M/m to reset it.
continued
Checking/changing/cancelling timer settings
59
about 20 seconds
Programme 2
will be cut off
Programme 1
Programme 2
about 20 seconds will be cut off
Display window
Main
MAIN
STEREO
Sub
SUB
STEREO
MAIN/SUB
STEREO
Standard sound*
MONO
STEREO
* Usually the main channel heard from both the left and right in bilingual
programmes
Additional Operations
To listen to
On-screen display
Display window
Stereo
STEREO
STEREO
Left channel
LCH
STEREO
Right channel
RCH
STEREO
Standard sound
LCH + RCH
STEREO
* Usually the mixed sound of left and right channels in stereo programmes
continued
Recording stereo and bilingual programmes (not available on SLV-SE230D)
61
On-screen display
Display window
Stereo
NICAM, STEREO
STEREO
Left channel
NICAM, LCH
STEREO
Right channel
NICAM, RCH
STEREO
On-screen display
Display window
Main
NICAM, MAIN
STEREO
Sub
NICAM, SUB
STEREO
NICAM, MAIN/SUB
STEREO
Standard sound*
NICAM, MONO
STEREO
On-screen display
Display window
Stereo
STEREO
STEREO
Left channel
LCH
STEREO
Right channel
RCH
STEREO
Mix sound*
MIX
STEREO
Mono sound
MONO
No indicator
* The mixed sound of left and right channels, and the normal mono audio track
Stereo
Usually mixed
left/right channels
Bilingual
Usually main sound
Additional Operations
Notes
To listen to playback sounds in stereo, you must use the Scart or AUDIO OUT
connections.
When you play a tape recorded in monaural, the sound is heard in monaural
regardless of the AUDIO MONITOR setting.
63
: BB
3 Press H (play) to start playback when you find the desired point.
To search a specific recording (Index search)
INDEX SEARCH : B B + 0 2
Each time you press the button, the number increases or decreases up to
20, respectively.
The VCR starts searching, and playback starts automatically from that
point.
To stop searching
Press x (stop).
Notes
No index signal will be added when recording starts from recording pause.
However, an index signal will be marked if you change the programme position
during recording pause.
When you press . (index search), if there is nothing recorded before the
selected index signal, playback may not start exactly at the index signal.
Additional Operations
Searching using the index function (not available on SLV-SE230D)
65
TRA CK I NG
Tracking meter
: ON
: E1 8 0
: A UTO
: A UTO
: ON
: OFF
: ON
SET
:
E X I T : M E NU
P I CTURE
: ON
: E1 8 0
: A UTO
: A UTO
: ON
: E CO1
: ON
SET
:
E X I T : M E NU
Additional Operations
67
O SD
T APE SELECT
C O LO UR SYST EM
F O RMAT 1 6 : 9
NI C AM
PO WER SAVE
SMAR T T RI LO G I C
SELECT :
END
: OK
: ON
: E1 8 0
: AU T O
: AUT O
: ON
: OFF
: ON
SET
:
EXI T : MENU
V P S / P DC DE FA UL T
S HOW V I E W E X TE ND
A UTO P OW E R OFF
TI M E R M E THOD
S E L E CT
E ND
:
: OK
: OFF
: OFF
: OFF
: V A RI A B L E
SET
EXIT
:
: M E NU
OSD
TAPE SELECT
COLOUR SYSTEM
FORMAT 16:9
NICAM*1
Menu option
POWER SAVE
SMART TRILOGIC
EASY OPERATION
Set this option to
VPS/PDC
DEFAULT*2
SHOWVIEW
EXTEND*2
AUTO POWER OFF OFF to deactivate the Auto Power Off function.
2HOUR/3HOUR to turn the VCR off automatically if no
signal is received and you do not press any of the buttons
during this time.
TIMER METHOD*2
Additional Operations
Menu option
69
Editing
TV
Scart
(EURO-AV)
: Signal flow
Example B (SLV-SE830D/E only)
TV
t LINE-2 L o R
(open cover to connect)
LINE OUT
: Signal flow
Example C
Your VCR (Recorder)
TV
LINE-3 (DEC/EXT)*1 or
LINE-2 (DEC/EXT)*2
Scart
(EURO-AV)
Editing
: Signal flow
71
Basic editing
When recording on this VCR
Before you start editing
REC z
a source tape with its safety tab removed into the other (playback)
1 Insert
VCR. Search for the point to start playback and set it to playback pause.
a tape with its safety tab in place into this (recording) VCR.
2 Insert
Search for the point to start recording and press X (pause) to set it to
playback pause.
Press REC z on this VCR to set it to recording pause.
3
start editing, press the X (pause) buttons on both VCRs at the same
4 To
time.
To stop editing
Press the x (stop) buttons on both VCRs.
Tip
To cut out unwanted scenes while editing, press X (pause) on this VCR when an
unwanted scene begins. When it ends, press X (pause) again to resume recording.
* not available on SLV-SE230D
72 Basic editing
AUDIO DUB
t LINE-2 L o R
X (pause).
3
4
Editing
a source tape into your stereo system (or the playback VCR).
1 Insert
Search for the point to start playback and set it to playback pause.
a prerecorded tape with its safety tab in place into this (recording)
2 Insert
VCR. Search for the start of the section to be replaced and press
The VCR enters pause mode.
Press AUDIO DUB.
A_DUB and the indicator appears in the display window.
To start editing, press the X (pause) buttons on this VCR and the stereo
system (or other VCR) at the same time.
After you use this feature, the audio in playback mode is automatically
set to monaural.
To stop editing
Press x (stop) on this VCR and the stereo system (or other VCR).
73
Additional Information
Troubleshooting
If you have any questions or problems not covered below, please consult your nearest
Sony service facility.
Symptom
Remedy
Playback
Clock
Power
74 Troubleshooting
Playback
Recording
No TV programme
appears on the TV
screen.
TV reception is poor.
Timer recording
Remedy
continued
Troubleshooting
Additional Information
Symptom
75
Timer recording
PAY-TV/Canal Plus
Others
Symptom
Remedy
Check that the clock and the date are set correctly.
Check that the VPS/PDC time you set is the correct one
(there might be a mistake in the TV programme guide). If
the broadcast you wanted to record did not send the good
VPS/PDC information, the VCR will not start recording.
If the reception is poor, the VPS/PDC signal might be
altered and the VCR might not start recording.
You cannot watch PAY Check that DEC is set to ON for this channel in the TV
TV/Canal Plus
STATION TABLE menu.
programmes when the
Make sure the PAY-TV/Canal Plus Scart cable is plugged
VCR is in standby mode.
securely.
A PAY-TV/Canal Plus
programme is always
recorded scrambled.
A tape cannot be
inserted.
Set your TVs code number. The code number may change
when you replace the batteries of the remote commander.
Clean the cabinet, panel and controls with a dry, soft cloth,
or a soft cloth slightly moistened with a mild detergent
solution. Do not use any type of solvent, such as alcohol or
benzine.
76 Troubleshooting
Rough picture
initial
contamination
Unclear picture
No picture (or
black & white
screen appears)
terminal
Additional Information
Troubleshooting
77
Specifications
System
Channel coverage
PAL (B/G)
VHF E2 to E12
VHF Italian channel A to H
UHF E21 to E69
CATV S01 to S05, S1 to S20
HYPER S21 to S41
RF output signal
UHF channels 21 to 69
Aerial out
75-ohm asymmetrical aerial socket
Tape speed
SP: PAL 23.39 mm/s (recording/
playback)
NTSC 33.35 mm/s (playback only)
LP: PAL 11.70 mm/s (recording/
playback)*
NTSC 16.67 mm/s (playback only)
EP: NTSC 11.12 mm/s (playback only)*
Maximum recording/playback time
10 hrs. in LP mode (with E300 tape)
Rewind time
Approx. 1 min. (with E180 tape)
* not available on SLV-SE230D
78 Specifications
*1 SLV-SE830D/E only
*2 not available on SLV-SE630D/E and
SE230D
General
Power requirements
220 240 V AC, 50 Hz
Power consumption
SLV-SE230D
15 W
1.2 W (POWER SAVE is set to ECO2,
minimum)
SLV-SE630D/E
17 W
1.2 W (POWER SAVE is set to ECO2,
minimum)
SLV-SE830D/E, SE737E, SX737D,
SE730D/E and SX730D/E
17 W
1.3 W (POWER SAVE is set to ECO2,
minimum)
Operating temperature
5 C to 40 C
Storage temperature
20 C to 60 C
Dimensions including projecting parts and
controls (w/h/d)
Approx. 360 95 245 mm
(SLV-SE230D)
Approx. 430 96 245 mm
(SLV-SE737E, SX737D, SE730D/E,
SX730D/E and SE630D/E)
Approx. 430 96 253 mm
(SLV-SE830D/E)
Mass
Approx. 2.8 kg (SLV-SE230D)
Approx. 3.1 kg (SLV-SE830D/E,
SE737E, SX737D, SE730D/E,
SX730D/E and SE630D/E)
Supplied accessories
Remote commander (1)
R6 (size AA) batteries (2)
Aerial cable (1)
Design and specifications are subject to
change without notice.
Index
A
Adjusting
picture 66
tracking 66
Aerial hookup 16
Audio dubbing 73
Audio track 63
Auto Clock Set 21
Auto Set Up 20
Canal Plus 35
Changing the programme
position 30
Changing the station name 33
Cleaning the video heads 74
Clock setting 23
Colour system
compatible colour systems
2
Connecting
the VCR and your TV 16,
17
to a stereo system 19, 70
to a TV with a Scart
(EURO-AV) connector 17
to video equipment 19
Counter 38
Country selection 21
NICAM broadcasts 61
Normal audio track 63
Searching
at various speeds 56
using the index function 64
ShowView
recording 49
Smart trilogic 66
SMARTLINK
NexTView Download 18
One Touch Menu 18
One Touch Play 18, 39
One Touch Timer 18
TV Direct Rec 18, 43
SP mode 40
Stereo 61
Optional setting 68
Timer setting 53
cancelling 59
changing 59
checking 59
daily/weekly recording 51,
54
using the Dial Timer 44
using the ShowView
system 49
D
Demonstration 48
Dial Timer 44
Disabling the programme
positions 31
Dubbing. see Editing
E
Editing 70
H
Hi-fi audio track 63
I
Index scan 64
Index search 64
P
PAY-TV 35
PDC (Programme Delivery
Control) 51
Playback 38
at various speeds 56
frame-by-frame 56
selecting the sound 62
slow motion 56
Power save 67
Preset download 25
Presetting channels 27
R
Recording 40
bilingual programmes 61
duration time 58
saving 42
stereo programmes 61
timer setting 53
using the Dial Timer 44
using the ShowView
system 49
what you are watching on
the TV 43
while watching another
programme 41
RF channel 20, 22
V
VPS (Video Programme
System) 51
W
Wide screen format 68
Z
ZWEITON broadcasts 61
S
Safety tab 42
Scart connection 17
Index
79
1
LINE-1
(EURO AV)
:Signal flow
channel.
If your TV does not have a Scart
(EURO-AV) connector, tune the TV to
channel 32 (the initial RF channel of this
VCR). Refer to your TVs manual for
TV tuning instructions. If the picture
does not appear clearly, see To change
the RF channel.
2 ... Connect the mains lead to the mains.
Sony Corporation
AC68-02034D