Professional Documents
Culture Documents
Navayuga Infotech
Page 1 of 9
Navayuga Infotech
Page 2 of 9
POLES
1. Pole number should not be duplicated.
2. Check for pole Type information with the asset design
3.
4.
5.
6.
7.
8.
document.
If pole classification is HT or LT then only corresponding
network lines should be connected.
If pole classification is both then both HT and LT network
lines can connect.
Height and Pole_Loc should be verified.
If Street Light updated as No, Then Type of Light field
should be NA, If Street Light updated as yes then Type of
Light should be updated as mentioned in possible values.
Type_Supp can only have STAY WIRE or STUD or NO.
HT_LT_Shac should be YES/NO.
HT Line
line connected.
18. Pole from and Pole To fields should be updated.
Navayuga Infotech
Page 3 of 9
the conductor.
20. Depending on the Condu_Type and Condu_Name, size
should be checked as per asset design document.
21. Check the OH Line Height in meters for OH conductors
only, and check for depth if any UG conductors.
22. In general OH Line Height in meters on LT pole will be Pole
height-1
23. For BOTH poles it will be pole height-2.
24. DT_Name and DT_Code should be entered in same
manner as in DT FAT and the DT wise network also
verified.
BUSBAR
voltage.
IMPLANTLINE
27. Type should be HT or LT.
28. Status should be SERVICE or NOT IN SERVICE.
CAPACITOR
FUSE
32. Voltage should be corresponding Connected Lines voltage.
33. Type should be HG FUSE if on HT side, and FEEDER FUSE if
on LT side.
34. Phase should be RYB or R/Y/B depending on connected
lines.
Navayuga Infotech
Page 4 of 9
SWITCH
1. Type should be HT or LT.
2. Voltage should be corresponding Connected Lines voltage.
3. Status should be OPEN or CLOSE.
4. In general switch status will be CLOSE when placed on HT
lines it will be in OPEN state when placed on LT lines.
5. When switch placed to avoid the looping conditions, it
should be in OPEN state, weather it is placed on HT line or
LT line.
DISTRIBUTION TRANSFORMER ENERGY METER (DTEM)
6. Check for DT code entered as same as in DT FAT.
7. CT_Rat_Avl, CT_Rat_Adp, STR_of_CT is need to be updated.
8. Meter_S_No should be entered and not to be duplicated.
9. TOD slots should be a numeric value.
10.
11.
Current, Voltage, Power_Fact, Frequency need to be
entered.
12.
KW, KVAr, Kwh, KVAh should be entered if Meter is in
working condition.
13.
Physical Status should be SERVICE or NOT IN
SERVICE.
Navayuga Infotech
Page 5 of 9
15.
16.
PT_Rat_Avl, PT_Rat_Adp, CT_Rat_Avl, CT_Rat_Adp
should be updated.
17.
Meter_Type, Meter Make, Meter Model, Meter_DOM,
Meter_P_O should be entered if available.
18.
Current, Voltage, Power_Fact, Frequency should be
entered.
19.
KW, KVAr, Kwh, KVAh should be entered if Meter is in
working condition.
20.
21.
Physical Status should be SERVICE or NOT IN
SERVICE.
Navayuga Infotech
Page 6 of 9
Consumers
Navayuga Infotech
Page 7 of 9
Navayuga Infotech
Page 9 of 9