Professional Documents
Culture Documents
technology.
Unconditional
Lifetime Warranty
USER GUIDE
U-028 2013B-1004
Description
The RLH 8 Channel Contact Closure DIN Fiber Link
system provides a transmission of up to eight
independent contact closure signals over one optical
fiber. The system comprises a transmitter module and a
receiver module, each in a compact DIN mount housing.
The DIN mount is designed to be installed onto a
standard T35 (35mm) DIN rail.
Description
.......................................................................1
Standard Features
.............................................................1
General Safety Practices
.................................................2
Acronyms
..........................................................................2
Applications
......................................................................3
System Diagram
................................................................3
Connectors
........................................................................3
Installation
.........................................................................4
Troubleshooting
..............................................................5
LED Indicators
.................................................................5
Ordering Information
....................................................6
Specifications
.....................................................................7
Warranty
...........................................................................8
Technical Support
...........................................................8
Standard Features
Page 1
Never install during a lightning storm or where unsafe high voltages are present.
Use caution when handling copper wiring and follow appropriate safety regulations.
Do not bend fiber cable sharply. Use gradual and smooth bends to avoid damaging glass fiber.
Keep dust caps on fiber optic connectors at all times when disconnected.
Keep fiber ends and fiber connectors clean and free from dust, dirt and debris. Contamination will cause
signal loss.
Acronyms
Commonly used acronyms and abbreviations
Acronym/Abbreviation
Page 2
Description
TX
Transmit
RX
Receive
PWR
Power
CH
NO
Normally Open
NC
Normally Closed
ORJ
Orange
BLU
Blue
Applications
Network equipment in high voltage areas can be at risk due to Ground Potential Rise (GPR). A copper
network cable referenced to a remote ground can become a path for high voltages during a ground fault.
Placement of all-dielectric fiber optic cable (instead of copper) completely eliminates the presence of a
remote ground, which dramatically increases safety of personnel and reliability of equipment.
By utilizing fiber optic cable, the Contact Closure DIN Fiber Link System provides absolute electrical
isolation between both ends of the network. It is immune to EMI/RF interference, ground loops, and high
voltage surges from lightning or ground faults, and is ideal in electrically noisy environments such as near
large power sources, electrical motors, and radio communications equipment.
Contact Closure
TX Unit (CO)
24~56VDC
P.S.
Contact Closure
RX Unit (Sub)
8 Contacts In
8 Contacts Out
DC Power
DC Power
TX
RX
LNK
PWR ALM
FIBER
Fiber Optic
Connector
FIBER
Fiber Optic
Connector
PWR
ALARM
Alarm
CH5
CH6
CH3
CH7
CH3
Contacts 1~4
Contacts 5~8
CH7
CH4
CH8
CH4
CHANNEL
CHANNEL
CONTACT
CLOSURE
CONTACT
CLOSURE
CH8
COM NO NC
CH6
CH2
CH5
CH2
CH1
CH1
Contacts 1~4
Contacts 5~8
Page 3
Installation
Prior to installation:
Measure the DC voltage of the source power to ensure that it is 24-56VDC. All electrical and fiber optic
connection are made directly onto the unit.
Connect Power
Connect a 24-56VDC power source wiring to the screw-down terminals indicated as DC POWER. The
power input is not polarity sensitive. The terminal unplugs from the module to make wiring easier.
Note: Connect a chassis ground wire to the screw on the top or bottom of the module housing to reduce
the chance of damage from lightning or other high voltage events.
Page 4
Troubleshooting
If trouble is encountered, verify all copper and fiber connections, signal and voltage levels. If the alarm is
on, double check the alarm jumper, fiber cable and connections, or TX side power source and
connections.
RX
LNK
PWR ALM
RX
LNK
PWR ALM
FIBER
FIBER
ALARM
CH1
CH5
CH2
COM NO NC
CH6
CH3
CH7
CH4
CH8
ALARM
COM NO NC
CH1
CHANNEL
CONTACT
CLOSURE
CH2
CH5
PWR
BLU
8
BLU
CHANNEL
LNK
RX
ALARM
CH1 ~ CH8
CONTACT
ORG
CLOSURE
State
Description
ON
OFF
Power is disconnected
CH8
PWR
Color
CH7
TX
CH4
Indicator
CH6
CH3
Module
ON
OFF
Power is disconnected
ON
OFF
ON
Fiber optic signal is not present
RED RLH Industries, Inc.
OFF
Fiber optic signal is detected
8 channel contact closure over fiber
GRN
ON
OFF
If trouble persists, replace the unit and retest. If technical assistance is required, contact
RLH Industries, Inc. technical support department:
800-877-1672 (6 am to 6 pm- PST),
or call our 24/7 Technical/Customer Service: (714) 366-2503 or (714) 457-5740
Page 5
Ordering Information
Each 4 Channel Contact Closure DIN Fiber Link system is identified with a part number.
Part Number
Description
Distance
Fiber
Part Number
Multimode
SC
TX Card
2km / 1.2 mi
62.5 m
8CD-01-2
RX Card
2km / 1.2 mi
62.5 m
8CD-02-2
Multimode
ST
TX Card
2km / 1.2 mi
62.5 m
8CD-03-2
RX Card
2km / 1.2 mi
62.5 m
8CD-04-2
Multimode
SC
TX Card
2km / 1.2 mi
50 m
8CD-05-2
RX Card
2km / 1.2 mi
50 m
8CD-06-2
Multimode
ST
TX Card
2km / 1.2 mi
50 m
8CD-07-2
RX Card
2km / 1.2 mi
50 m
8CD-08-2
TX Card
15km / 9 mi.
8~9 m
8CD-10-2
TX Card
48km / 29 mi.
8~9 m
8CD-11-2
RX Card
8~9 m
8CD-12-2
TX Card
15km / 9 mi.
8~9 m
8CD-20-2
TX Card
48km / 29 mi.
8~9 m
8CD-21-2
RX Card
8~9 m
8CD-22-2
Single-mode
SC
Single-mode
ST
Page 6
General Specifications
Amplitude modulated light via two optical fibers
Transmission method
Multimode:
850nm
Single-mode:
1310nm
1310nm
Multimode:
Single-mode:
Fiber Type
ST or SC connectors
Multimode:
62.5/125m, 50/125m
Single-mode:
8-9/125m
Wire Connector
Response Time
10ms
Surge Protection
Power Requirements
TX Module:
RX Module:
Powering Method
Operating Temperature
Mounting
Dimensions
Page 7
Warranty
RLH is recognized throughout the U.S. and offers the only UNCONDITIONAL LIFETIME
WARRANTY in the telecommunications industry. We are very proud of our warranty which
simply states that our transmission products are guaranteed to be free of defects in
material and workmanship for the LIFE OF THE PRODUCT. Look for the warranty badge.
Technical Support
Normal technical support:
(714) 532-1672
Email:
support@fiberopticlink.com
Contact Information
Corporate Headquarters:
Phone:
(714) 532-1672
Toll Free 1-800-877-1672
Toll Free 1-866-DO-FIBER
Fax:
(714) 532-1885
Email:
info@fiberopticlink.com
Web site:
www.fiberopticlink.com
Page 8