Professional Documents
Culture Documents
1.
504.3
2.
For
(Page 36)
The distance between centres of the main Replace main girders by main outermost
girders shall be sufficient to resist overturning girders
or over stressing due to lateral forces and
loading conditions
504.4(b)
(Page 36)
(Page 37)
Beams and plate girders upto and including Substitute the following for the existing:
35 m span need not be cambered
It is not mandatory to camber beams and plate
girders upto and including 35 m span
507.5.1.2
(Page 63)
The flexural torsional buckling strength of in place of in clause 507.1.2.1 and using
single angle loaded in compression through curve C ( = 0.49) of Fig. 5
one of its legs may be evaluated using the
equivalent slenderness ratio e as given
below:
IR
4.
504.6.2(a)
5.
3.
Read
509.3.1
Table 12
(Page 86)
Second Column
Warping
Restraint Line
1
6.
509.3.1
101
Amendment to IRC:24-2010
Sl.No.
7.
509.4.2.2(b)
For
tan-1(d/c)
d
-1 c
nearly tan
1.5
(Page 94)
509.5.1
Fig.7 Note 2
(Page 95)
9.
514.4.5
(Page 170)
10.
514.5.9
The method of erection, as also the drawing Substitute the following for the existing:
of the temporary work and the use of erection
The Engineer shall approve the procedure of
equipment, shall be subject to the approval
erection, drawings of temporary works and use
by the Engineer.
of erection equipment, prior to commencement
of erection.
IR
(Page 171)
Panel B is designed without utilizing tension Substitute the following for the existing:
filed action as given in Clause 509.4.2.2(a)
Panel B is designed using simple post-critical
method as given in Clause 509.4.2.2(a)
8.
Read
102
Errata to IRC:24-2010
Errata No. 1/ IRC:24-2010/January 2014
To
IRC:24-2010 Standard Specifications and Code of Practice for Road Bridges
Section V
Steel Road Bridges (Limit State Method) (Third Revision)
1.
2.
3.
4.
5.
(Page 11)
Cl.503.1.2(c)
Lines 4&5
For
Read
(Page 28)
Cl.503.2.2 Line 2
. The limits states are classified Replace limits states by limit states
as: ..
(Page 29)
Cl.503.5.2 Line 2 . the partial safety factor for Replace (f) by (f)
loads (f) shall be..
(Page 31)
Table 2 Column 2 D/tf
Replace by d/t
Against Stem of a
T-Section etc
(Page 33)
Table 2 Column 2 D/tf
Against Circular
hollow tube etc.
Replace by D/t
IR
6.
Sl. No.
7.
8.
9.
10.
(Page 33)
Fig. 1 Figure
for ROLLED
CHANNELS
(Page 35)
Cl. 506.1.2.3
Line 6
(Page 41)
Fig. 5
(Page 50)
Cl.507.5.1.2
Line 7
Replace by d
fumo/fyml
Replace by 0.9fumo/fyml
Existing figure does not show Insert as the title of the abscissa (X-axis)
the title of the abscissa
vv =
(Page 63)
=
(l / rvv )
2 / 250
(b1 + b2 )/ 2t
2 / 250
and
l
r
vv = vv and
2 E
250
=
(b1 + b2 )/ 2t
2 E
250
103
Errata to IRC:24-2010
11.
12.
13.
14.
15.
16.
17.
18.
For
d/tw 67
KL/r
h/tf
Replace by LLT/ry,
Replace by hf / tf
(Page 84)
Table 13 Last row, Existing figure shows
First Column:Free flange gusset
(Page 88)
Cl.509.4.2.1
Read
and fy
(Page 92)
Cl.509.4.2.2(b)
Line 12
b = buckling strength.
(Page 93)
Cl.509.4.2.2 (b)
Line 18
(Page 94)
Cl.509.6.1.1(a)
Clause 509.4.2.2(a)
(Page 97)
Cl.509.6.1.1(b)(iii) c < d
(Page 98)
Cl.509.6.1.1(d)
20.
(Page 98)
Cl.509.6.1.2(b)
21.
(Page 99)
Cl.510.3.1.2(c)
w =
250 / f yw
IR
19.
Sl. No.
(Page 113)
f =
250 / f yf
Table 15
23.
(Page 116)
Cl.511.6 Line 1
(Page 129)
24.
Cl.512.6.4 Line 8
25.
(Page 149)
Cl.C1.2 Line 3
22.
Table 15
Replace by (LLT)2
(Page 177)
104
Errata to IRC:24-2010
26.
27.
(Page 177)
Table C.1
28.
29.
30.
For
(z2 - y2)
(Page 178)
Table C1(contd..) : Under c2 : Line 7 1.257
Constants
Under c3 : Line 5 : 1.780
(Page 179)
Under c3 : Line 10 : 1.390
Cl. C1.2
It = The torsion constant.
(Page 179)
Cl. G4.6.2
Definition of k2
Line 4
(Page 222)
Read
Replace by 1.267
Replace by 1.730
Replace by 1.890
Replace by It = St Venants torsion
constant.
Sl. No.
IR
105
Errata to IRC:24-2010
IR
106