You are on page 1of 8

REMOTE CONTROL HELICOPTER

In this instruction of material, the specification or parts within the accessories bag is for
reference only. The company will not be responsible for any change of printed part and
notify the consumers. Any update or change please refer to the website of SYMA
(www.symatoys.com).

1. Please recheck the ground, keep away from the crowds, animals and other barriers.
2. Turn the remote control on, after a while, the LEDs will be flashing. Push the motive handle must
be pushed to the maximum control route of travel first, then adjust it to the lowest; When the
remote control LEDs keep lighting, it means the helicopter is going to fly.
3.Open remote control power switch, then the remote status light was flashing and accompanied by
the rhythmic sound, and then push up the up / down variable speed joystick to the top, then its
back to the most low-end; the status of the remote controlThe indicator is lit and the sound stopped,
the remote control to enter the preparatory off state.
4. Push the motive handle slowly, then the helicopter will fly up.

Low-voltage protection: When the helicopter battery is low, the helicopter control system
battery will be protected, and stop the supply of helicopter rotor; low power protection,
the need to charge to secure a new flight of the helicopter.
Overcurrent protection: When the helicopter blades in the rotating state by collision or
jammed, the helicopter circuit overcurrent protection.

PC USB
First turn off the power switch of the helicopter, "USB cable charging plug to the charging port is
connected to the helicopter, and then" USB cable " The USB end into the USB port of a PC computer
to charge or connect the USB power adapter for charging (USB power adapter sold separately);
charging, USB line indicator lights switch off automatically after charging is completed ; charging
time is 60-90 minutes.

Charging time: can be 60~90 minutes flying about 6 minutes!

Remote Control Keypad and LCD Manual

Antenna

Power On/Off

Power Indicator
H/L Speed Switch

Left Function Lever


(Throttle Lever)

Right Function Lever


(Direction Lever)
Turn Lft/Right Fine-tuning

17 16
15 181214
11 1013
4 5 98 67 5 2
3 1

Tail Blade Fine-tuning

LCD Manual
Helicopter shows
(Power-on display)

H/L Speed Shows


(Changed by "H/L Speed Switch")

Signal Shows
(Normal to full case

10

Turn Left Shows


(Power-on without display
Throttle shows
(Power-on start in middle)

11

8
6

7
4

Backward ShowsPower-on
without display)

2
1

Battery Indicator(According to
the power of batteries)
Forward Shows(Power-on start
in the centering)
Turn Right Shows(Power-on without
display)
Tail Blade Fine-tuning(Power-on
start in middle

36

Turn Left/Right Fine-tuning Shows


(Power-on start in centering)

H/L Speed Switch

1.Beginner mode (the default setings


low speed)
2.Advanced mode:Press the button
on top left of controller, enter or
exit from the mode. Advanced
mode high speed brings more
pleasure to you

Rotates Anticlockwise

Rotates
Anticlockwise
Rotates Clockwise

Rotates
Clockwise
In hovering,when the tail
blade rotates clockwise
anticlockwise,please use
this button for fine-tuning
as figure shows.

When the helicopter lose


hovering with automatic
anticlockwise/clockwise
rotation,please use the
right/left inching switch
yo keep balance.

Problem
No reaction
from the
helicopter
Not reaction
from the
helicopter
when was fly

Cause

Check this

1. Not enough power for the helicoper.


2. Not enough power for the controller.
3. The channel was different from helicopter and the
controller.
4. The gyro of the helicopter can't find out the right
point.

1. helicopter for charging.


2. replace the remote control batteries.
3. Close the remote control and the aircraft power
supply, re-code.
4.The helicopter flat on the ground, re-open the helicopter
power until the helicopter gyro re-tested.

1. the remote control are running low.


2. antenna Weld.

1. replace the remote control batteries.


2. antenna re-welding.

S32-01A
Head cover A

S32-01B
Head cover B

S32-01C
Head cover C

S32-02C
Tail decoration C

S32-03A
Main blades

S32-05B
Connect buckle

S32-06
Ascend and descend

S32-07
Gear A B

S32-10A
Battery case

S32-12A
Tail hold tube

S32-12B

S32-12C
Metal frame set

S32-13B
Motor B

S32-14
3.7V Li-Poly

S32-15
Circuit board

S32-11
Tail components

S32-13A
Motor A

S32-17
Transmitter

S32-03B
Tail blade

S32-02A
Tail decoration A

S32-04
Main frame

S32-02B
Tail decoration B

S32-05A
Balance bar

S32-10B
Motor cover

S32-12D
Main shaft

S32-16
USB Charger

You might also like