You are on page 1of 117

LC-32/40/46LE600E/RU/S

PartsGuide

PARTS GUIDE
No. S89B5LC32L600

LCD COLOUR TELEVISION

LC-32LE600E/RU/S
LC-40LE600E/RU/S
MODELS LC-46LE600E/RU/S
Note:
The reference numbers on the PWB
are arranged in alphabetical order.

CONTENTS
[1]

PRINTED WIRING BOARD


ASSEMBLIES

[7]

LCD PANEL MODULE UNIT (LC40LE600E/RU/S)

[2]

LCD PANEL

[8]

CABINET AND MECHANICAL


PARTS (LC-46LE600E/RU/S)

[3]

DUNTKF111FM11 (MAIN Unit)


[9]

LCD PANEL MODULE UNIT (LC46LE600E/RU/S)

[4]

CABINET AND MECHANICAL


PARTS (LC-32LE600E/RU/S)

[10] SUPPLIED ACCESSORIES


[5]

[6]

LCD PANEL MODULE UNIT (LC32LE600E/RU/S)


CABINET AND MECHANICAL
PARTS (LC-40LE600E/RU/S)

[11] SERVICE JIGS (USE FOR


SERVICING)

INDEX

Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these
parts with specified ones for maintaining the safety and performance of the set.
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.

LC-32/40/46LE600E/RU/S
NO.

PARTS CODE

PRICE NEW
RANK MARK

PART
DELIVERY

DESCRIPTION

[1] PRINTED WIRING BOARD ASSEMBLIES

!
!
!

N
N
N
N
N
N
N
N
N
N
N
N
N
N
N

DUNTKE266FM18
DUNTKF111FM11
DUNTKF308FM02
RUNTKA619WJQZ
RUNTKA609WJQZ
RUNTKA611WJQZ
RUNTK4248TPZB
RUNTK4248TPZA
RUNTK4248TPZZ
RUNTKA595WJ01
RUNTKA595WJ02
RUNTKA596WJ01
RUNTKA596WJ02
RUNTKA598WJ01
RUNTKA598WJ02

AR
CA
AL
BS
BW
BZ
BL
BL
BL
AX
AX
AY
AY

N
N
N
N
N
N
N
N

P
P
P
P
P
P
P
P
P
P
P
P
P
P
P

KEY Unit
MAIN Unit
R/C, LED Unit
POWER Unit (LC-32LE600E/RU/S)
POWER Unit (LC-40LE600E/RU/S)
POWER Unit (LC-46LE600E/RU/S)
LCD Control Unit (LC-32LE600E/RU/S)
LCD Control Unit (LC-40LE600E/RU/S)
LCD Control Unit (LC-46LE600E/RU/S)
LED5-PWB1 Unit
LED5-PWB2 Unit
LED6-PWB1 Unit (LC-40/46LE600E/RU/S)
LED6-PWB2 Unit (LC-40/46LE600E/RU/S)
LED8-PWB1 Unit (LC-32/46LE600E/RU/S)
LED8-PWB2 Unit (LC-32/46LE600E/RU/S)

N
N
N

P
P
P

32"LCD Panel Module Unit (LC-32LE600E/RU/S)


40"LCD Panel Module Unit (LC-40LE600E/RU/S)
46"LCD Panel Module Unit (LC-46LE600E/RU/S)

J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J

Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor

[2] LCD PANEL


N
N
N

DLCUCA001FM02
DLCUCA002FM02
DLCUCA003FM02

[3] DUNTKF111FM11 (MAIN Unit)


C501
C502
C503
C507
C508
C510
C520
C521
C522
C523
C524
C525
C526
C527
C528
C529
C530
C531
C532
C533
C534
C535
C536
C537
C538
C539
C540
C541
C542
C543
C544
C545
C546
C547
C548
C549
C550
C551
C552
C553
C554
C555
C556
C557
C558
C559
C560
C561
C562
C564
C565
C566
C567
C568
C569
C570
C571
C572
C573
C575
C576
C577
C578

VCKYCZ1HB221KY
VCKYCZ1HB221KY
VCCCCZ1HH101JY
VCCCCZ1HH101JY
VCKYCZ1HB102KY
VCKYCZ1HB102KY
VCKYCZ1HB221KY
VCKYCZ1EF104ZY
VCKYCZ1HB331KY
VCKYCZ1HB331KY
VCCCCZ1HH101JY
VCCCCZ1HH101JY
VCKYCZ1HB331KY
VCKYCZ1HB331KY
VCKYCZ1HB102KY
VCKYCZ1HB102KY
VCKYCZ1HB471KY
VCKYCZ1HB471KY
VCCCCZ1HH101JY
VCCCCZ1HH101JY
RC-KZA510WJPZY
RC-KZA510WJPZY
VCKYCZ1HB471KY
VCKYCZ1HB471KY
VCKYCZ1HB102KY
VCKYCZ1HB102KY
RC-KZA510WJPZY
RC-KZA510WJPZY
RC-KZA510WJPZY
RC-KZA510WJPZY
RC-KZA510WJPZY
RC-KZA510WJPZY
VCKYCZ1HB102KY
VCCCCZ1HH560JY
VCCCCZ1HH560JY
VCKYCZ1HB102KY
VCCCCZ1HH100DY
VCERMZ1CN477MY
VCCCCZ1HH101JY
VCCCCZ1HH100DY
VCKYCZ1HB102KY
VCKYCZ1EF104ZY
VCCCCZ1HH100DY
VCKYCZ1EF104ZY
VCKYCZ1HB102KY
VCKYCZ1HB102KY
VCKYCZ1HB102KY
VCKYCZ1EF104ZY
VCCCCZ1HH101JY
RC-KZA616WJQZY
VCKYCZ1HB472KY
VCKYCZ1HB472KY
VCEASX1VN226MY
VCEASX1VN226MY
VCKYCY1AB105KY
RC-KZA067WJZZY
VCCCCZ1HH101JY
VCCCCZ1HH101JY
VCKYCZ1EF104ZY
VCKYCY1AB105KY
RC-KZA067WJZZY
RC-KZA616WJQZY
VCKYCZ1EF104ZY

AA
AA
AB
AB
AB
AB
AA
AA
AA
AA
AB
AB
AA
AA
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AE
AB
AB
AB
AA
AB
AA
AB
AB
AB
AA
AB
AB
AA
AA
AC
AC
AB
AB
AB
AB
AA
AB
AB
AB
AA

220p 50V Ceramic


220p 50V Ceramic
100p 50V Ceramic
100p 50V Ceramic
1000p 50V Ceramic
1000p 50V Ceramic
220p 50V Ceramic
0.1 25V Ceramic
330p 50V Ceramic
330p 50V Ceramic
100p 50V Ceramic
100p 50V Ceramic
330p 50V Ceramic
330p 50V Ceramic
1000p 50V Ceramic
1000p 50V Ceramic
470p 50V Ceramic
470p 50V Ceramic
100p 50V Ceramic
100p 50V Ceramic

470p 50V Ceramic


470p 50V Ceramic
1000p 50V Ceramic
1000p 50V Ceramic

1000p 50V Ceramic


56p 50V Ceramic
56p 50V Ceramic
1000p 50V Ceramic
10p 50V Ceramic
470 16V (AL)
100p 50V Ceramic
10p 50V Ceramic
1000p 50V Ceramic
0.1 25V Ceramic
10p 50V Ceramic
0.1 25V Ceramic
1000p 50V Ceramic
1000p 50V Ceramic
1000p 50V Ceramic
0.1 25V Ceramic
100p 50V Ceramic
4700p 50V Ceramic
4700p 50V Ceramic
22 35V Electrolytic
22 35V Electrolytic
1 10V Ceramic
100p 50V Ceramic
100p 50V Ceramic
0.1 25V Ceramic
1 10V Ceramic

0.1 25V Ceramic

LC-32/40/46LE600E/RU/S
NO.

PARTS CODE

PRICE NEW
RANK MARK

PART
DELIVERY

DESCRIPTION

[3] DUNTKF111FM11 (MAIN Unit)


C579
C580
C581
C582
C583
C584
C585
C586
C587
C588
C591
C592
C593
C1102
C1103
C1104
C1105
C1106
C1107
C1112
C1113
C1114
C1115
C1116
C1117
C1118
C1119
C1120
C1121
C1122
C1123
C1125
C1126
C1127
C1128
C1129
C1130
C1131
C1137
C1301
C1302
C1303
C1304
C1305
C1306
C1307
C1308
C1309
C1310
C1311
C1312
C1313
C1314
C1315
C1316
C1317
C1318
C1319
C1320
C1321
C1322
C1323
C1324
C1325
C1326
C1327
C1328
C1329
C1330
C1331
C1332
C1513
C1515
C1523
C1526
C1527
C1528
C1529
C1530
C2601
C2702
C2703
C2706
C2707
C2708

VCKYCZ1EF104ZY
VCKYCZ1EF104ZY
RC-KZA510WJPZY
VCKYCY1AB105KY
VCKYCY1AB105KY
VCKYCZ1EF104ZY
VCKYCY1AB105KY
VCKYCZ1EF104ZY
VCCCCZ1HH330JY
VCCCCZ1HH330JY
RC-KZA616WJQZY
VCKYCZ1AB104KY
RC-KZA616WJQZY
VCKYCZ1HB102KY
VCKYCZ1EB103KY
VCERML1CN107MY
VCKYCZ1EB103KY
RC-KZA510WJPZY
VCERMZ1CN477MY
VCKYCZ1EF104ZY
VCKYCZ1EB103KY
RC-KZA510WJPZY
VCKYCZ1EB103KY
RC-KZA510WJPZY
RC-KZA510WJPZY
RC-KZA510WJPZY
RC-KZA510WJPZY
RC-KZA510WJPZY
RC-KZA510WJPZY
RC-KZA510WJPZY
RC-KZA510WJPZY
RC-KZA510WJPZY
VCKYCZ1EB103KY
RC-KZA114WJZZY
VCKYCZ1EF104ZY
VCCCCZ1HH101JY
VCCCCZ1HH330JY
VCCCCZ1HH330JY
VCKYCZ1EF104ZY
RC-KZA510WJPZY
RC-KZA510WJPZY
VCKYCZ1EF104ZY
RC-KZA510WJPZY
VCKYCZ1EF104ZY
RC-KZA510WJPZY
RC-KZA510WJPZY
RC-KZA510WJPZY
RC-KZA510WJPZY
RC-KZA510WJPZY
RC-KZA510WJPZY
RC-KZA510WJPZY
RC-KZA510WJPZY
RC-KZA510WJPZY
RC-KZA510WJPZY
VCKYCZ1EB103KY
RC-KZA510WJPZY
VCKYCZ1EB103KY
RC-KZA510WJPZY
RC-KZA510WJPZY
VCKYCZ1EB103KY
VCKYCZ1EB103KY
RC-KZA510WJPZY
VCKYCZ1HB472KY
VCKYCZ1HB472KY
VCKYCZ1HB472KY
VCKYCZ1HB472KY
VCKYCZ1HB472KY
VCKYCZ1HB472KY
VCKYCZ1EB103KY
RC-KZA510WJPZY
VCKYCZ1EF104ZY
RC-KZA520WJQZY
RC-KZA520WJQZY
RC-KZA520WJQZY
VCKYCZ1AB104KY
VCKYCZ1AB104KY
RC-KZA616WJQZY
RC-KZA616WJQZY
VCKYCZ1AB104KY
VCKYCZ1AB104KY
RC-KZA510WJPZY
RC-KZA510WJPZY
RC-KZA510WJPZY
RC-KZA510WJPZY
VCKYCZ1HB102KY

AA
AA
AB
AB
AB
AA
AB
AA
AB
AB
AB
AB
AB
AB
AA
AC
AA
AB
AE
AA
AA
AB
AA
AB
AB
AB
AB
AB
AB
AB
AB
AB
AA
AB
AA
AB
AB
AB
AA
AB
AB
AA
AB
AA
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AA
AB
AA
AB
AB
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB

J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J

Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor

0.1 25V Ceramic


0.1 25V Ceramic
1 10V Ceramic
1 10V Ceramic
0.1 25V Ceramic
1 10V Ceramic
0.1 25V Ceramic
33p 50V Ceramic
33p 50V Ceramic
0.1 10V Ceramic
1000p 50V Ceramic
0.01 25V Ceramic
100 16V (AL)
0.01 25V Ceramic
470 16V (AL)
0.1 25V Ceramic
0.01 25V Ceramic
0.01 25V Ceramic

0.01 25V Ceramic


0.1 25V Ceramic
100p 50V Ceramic
33p 50V Ceramic
33p 50V Ceramic
0.1 25V Ceramic

0.1 25V Ceramic


0.1 25V Ceramic

0.01 25V Ceramic


0.01 25V Ceramic

0.01 25V Ceramic


0.01 25V Ceramic
4700p 50V Ceramic
4700p 50V Ceramic
4700p 50V Ceramic
4700p 50V Ceramic
4700p 50V Ceramic
4700p 50V Ceramic
0.01 25V Ceramic
0.1 25V Ceramic

0.1 10V Ceramic


0.1 10V Ceramic

0.1 10V Ceramic


0.1 10V Ceramic

1000p 50V Ceramic

LC-32/40/46LE600E/RU/S
NO.

PARTS CODE

PRICE NEW
RANK MARK

PART
DELIVERY

DESCRIPTION

[3] DUNTKF111FM11 (MAIN Unit)


C2709
C2710
C2711
C2712
C2713
C2714
C2715
C2716
C2717
C2718
C2719
C2720
C2721
C2723
C2724
C2729
C2740
C2741
C3301
C3302
C3303
C3304
C3306
C3309
C3313
C3314
C3315
C3316
C3317
C3318
C3320
C3321
C3322
C3324
C3325
C3326
C3327
C3329
C3330
C3331
C3332
C3333
C3334
C3336
C3337
C3338
C3339
C3341
C3342
C3343
C3344
C3345
C3346
C3347
C3348
C3350
C3351
C3352
C3353
C3354
C3355
C3356
C3357
C3358
C3359
C3360
C3361
C3362
C3363
C3364
C3365
C3366
C3367
C3368
C3369
C3370
C3371
C3372
C3373
C3374
C3375
C3376
C3377
C3378
C3379

VCKYCZ1HB102KY
VCEASY1EN107MY
VCKYCY1AB105KY
VCKYCY1AB105KY
VCKYCY1AB105KY
VCKYCZ1EF104ZY
VCEASY1EN107MY
RC-KZA114WJZZY
RC-KZA114WJZZY
VCKYTV1EB474KY
VCKYTV1EB474KY
VCKYTV1EB474KY
VCKYTV1EB474KY
RC-KZA114WJZZY
RC-KZA114WJZZY
VCKYCZ1HB102KY
VCKYCZ1HB472KY
VCKYCZ1HB472KY
VCCCCZ1HH101JY
VCCCCZ1HH101JY
VCCCCZ1HH101JY
VCCCCZ1HH101JY
VCCCCZ1HH101JY
VCCCCZ1HH101JY
VCCCCZ1HH471JY
VCCCCZ1HH471JY
RC-KZA510WJPZY
VCAAPE0JJ227MY
VCKYCZ1EF104ZY
RC-KZA616WJQZY
RC-KZA510WJPZY
RC-KZA616WJQZY
RC-KZA576WJQZY
VCKYCZ1EF104ZY
RC-KZA576WJQZY
RC-KZA576WJQZY
VCKYCZ1AB104KY
VCKYCZ1AB104KY
VCKYCZ1AB104KY
VCKYCZ1AB104KY
RC-KZA616WJQZY
VCKYCZ1AB104KY
RC-KZA576WJQZY
RC-KZA616WJQZY
VCKYCZ1AB104KY
RC-KZA510WJPZY
VCCCCZ1HH101JY
VCKYCZ1AB104KY
VCKYCZ1AB104KY
VCKYCZ1AB104KY
RC-KZA576WJQZY
RC-KZA616WJQZY
VCKYCZ1AB104KY
VCKYCZ1AB104KY
RC-KZA616WJQZY
RC-KZA576WJQZY
VCKYCZ1HB472KY
RC-KZA510WJPZY
VCKYCZ1AB104KY
VCKYCZ1AB104KY
RC-KZA616WJQZY
RC-KZA616WJQZY
RC-KZA576WJQZY
VCKYCZ1EB103KY
VCKYCZ1HB472KY
VCKYCZ1EB103KY
VCKYCZ1AB104KY
VCKYCZ1AB104KY
VCKYCZ1EB103KY
VCKYCZ1AB104KY
VCKYCY1AB105KY
RC-KZA576WJQZY
VCKYCZ1AB104KY
VCKYCZ1EB103KY
VCKYCZ1EB103KY
VCCCCZ1HH8R0DY
VCCCCZ1HH8R0DY
VCKYCZ1AB473KY
VCKYCZ1AB473KY
VCKYCZ1AB473KY
VCKYCZ1AB473KY
VCKYCZ1EB103KY
VCKYCZ1EB103KY
VCKYCZ1EB103KY
VCKYCZ1EB103KY

AB
AC
AB
AB
AB
AA
AC
AB
AB
AC
AC
AC
AC
AB
AB
AB
AA
AA
AB
AB
AB
AB
AB
AB
AA
AA
AB
AE
AA
AB
AB
AB
AB
AA
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AA
AB
AB
AB
AB
AB
AB
AA
AA
AA
AB
AB
AA
AB
AB
AB
AB
AA
AA
AA
AA
AB
AB
AB
AB
AA
AA
AA
AA

J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J

Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor

1000p 50V Ceramic


100 25V Electrolytic
1 10V Ceramic
1 10V Ceramic
1 10V Ceramic
0.1 25V Ceramic
100 25V Electrolytic

0.47
0.47
0.47
0.47

25V
25V
25V
25V

Ceramic
Ceramic
Ceramic
Ceramic

1000p 50V Ceramic


4700p 50V Ceramic
4700p 50V Ceramic
100p 50V Ceramic
100p 50V Ceramic
100p 50V Ceramic
100p 50V Ceramic
100p 50V Ceramic
100p 50V Ceramic
470p 50V Ceramic
470p 50V Ceramic
220 6.3V Electrolytic
0.1 25V Ceramic

0.1 25V Ceramic

0.1
0.1
0.1
0.1

10V
10V
10V
10V

Ceramic
Ceramic
Ceramic
Ceramic

0.1 10V Ceramic

0.1 10V Ceramic


100p 50V Ceramic
0.1 10V Ceramic
0.1 10V Ceramic
0.1 10V Ceramic

0.1 10V Ceramic


0.1 10V Ceramic

4700p 50V Ceramic


0.1 10V Ceramic
0.1 10V Ceramic

0.01 25V Ceramic


4700p 50V Ceramic
0.01 25V Ceramic
0.1 10V Ceramic
0.1 10V Ceramic
0.01 25V Ceramic
0.1 10V Ceramic
1 10V Ceramic
0.1 10V Ceramic
0.01 25V Ceramic
0.01 25V Ceramic
80p 50V Ceramic
80p 50V Ceramic
0.047 10V Ceramic
0.047 10V Ceramic
0.047 10V Ceramic
0.047 10V Ceramic
0.01 25V Ceramic
0.01 25V Ceramic
0.01 25V Ceramic
0.01 25V Ceramic

LC-32/40/46LE600E/RU/S
NO.

PARTS CODE

PRICE NEW
RANK MARK

PART
DELIVERY

DESCRIPTION

[3] DUNTKF111FM11 (MAIN Unit)


C3380
C3381
C3382
C3383
C3384
C3385
C3386
C3387
C3388
C3389
C3390
C3391
C3392
C3393
C3394
C3395
C3396
C3397
C3399
C3400
C3401
C3402
C3403
C3404
C3501
C3502
C3503
C3504
C3505
C3506
C3507
C3508
C3509
C3510
C3511
C3512
C3513
C3514
C3515
C3516
C3517
C3518
C3519
C3520
C3521
C3522
C3523
C3524
C4401
C4402
C4403
C4404
C4405
C4406
C4407
C4408
C4409
C4410
C4411
C4412
C4413
C4416
C4417
C4418
C4419
C4420
C4421
C4424
C4425
C4426
C4428
C8455
C8456
C8457
C8460
C9601
C9602
C9604
C9607
C9608
C9609
C9610
C9611
C9612
C9613

VCKYCZ1EB103KY
VCKYCZ1EB103KY
VCKYCZ1AB473KY
VCKYCZ1EB103KY
VCKYCZ1EB103KY
VCKYCZ1EB103KY
VCKYCZ1EB103KY
VCKYCZ1EB103KY
VCKYCZ1EB103KY
RC-KZA510WJPZY
RC-KZA510WJPZY
VCKYCZ1AB473KY
RC-KZA510WJPZY
RC-KZA510WJPZY
RC-KZA510WJPZY
RC-KZA510WJPZY
RC-KZA510WJPZY
RC-KZA510WJPZY
VCKYCZ1CB223KY
VCKYCZ1AB104KY
RC-KZA067WJZZY
RC-KZA616WJQZY
VCKYCZ1AB104KY
VCKYCZ1AB473KY
VCKYCZ1EF104ZY
VCKYCZ1EF104ZY
VCAAPE0JJ107MY
RC-KZA510WJPZY
VCKYCZ1EF104ZY
VCKYCZ1EF104ZY
VCKYCZ1EF104ZY
RC-KZA576WJQZY
RC-KZA576WJQZY
RC-KZA576WJQZY
RC-KZA576WJQZY
VCKYCZ1EF104ZY
VCKYCZ1EF104ZY
RC-KZA510WJPZY
RC-KZA510WJPZY
VCKYCZ1EF104ZY
VCKYCZ1EF104ZY
VCKYCZ1EF104ZY
RC-KZA576WJQZY
RC-KZA576WJQZY
RC-KZA576WJQZY
RC-KZA576WJQZY
RC-KZA576WJQZY
RC-KZA510WJPZY
VCCCCZ1HH120JY
RC-KZA510WJPZY
VCCCCZ1HH100DY
VCKYCZ1EF104ZY
RC-KZA510WJPZY
VCKYCZ1EF104ZY
RC-KZA510WJPZY
VCKYCZ1EF104ZY
VCKYCZ1EF104ZY
RC-KZA510WJPZY
RC-KZA510WJPZY
VCKYCZ1EF104ZY
VCKYCZ1EF104ZY
VCKYCZ1EF104ZY
VCKYCZ1EF104ZY
VCKYCZ1EF104ZY
RC-KZA510WJPZY
VCAAPD1AJ686MY
RC-KZA510WJPZY
VCKYCY1AB105KY
VCKYCY1AB105KY
RC-KZA510WJPZY
RC-KZA510WJPZY
VCKYCZ1AB104KY
VCKYCZ1AB104KY
VCKYCZ1EF104ZY
VCKYCZ1AB104KY
VCKYCZ1HB472KY
RC-KZA114WJZZY
RC-KZA616WJQZY
RC-KZA616WJQZY
VCKYCY1AB105KY
RC-KZA616WJQZY
RC-KZA616WJQZY
RC-KZA616WJQZY
VCKYCZ1EB103KY
VCKYCZ1EF104ZY

AA
AA
AB
AA
AA
AA
AA
AA
AA
AB
AB
AB
AB
AB
AB
AB
AB
AB
AC
AB
AB
AB
AB
AB
AA
AA
AE
AB
AA
AA
AA
AB
AB
AB
AB
AA
AA
AB
AB
AA
AA
AA
AB
AB
AB
AB
AB
AB
AB
AB
AB
AA
AB
AA
AB
AA
AA
AB
AB
AA
AA
AA
AA
AA
AB
AE
AB
AB
AB
AB
AB
AB
AB
AA
AB
AA
AB
AB
AB
AB
AB
AB
AB
AA
AA

J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J

Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor
Capacitor

0.01 25V Ceramic


0.01 25V Ceramic
0.047 10V Ceramic
0.01 25V Ceramic
0.01 25V Ceramic
0.01 25V Ceramic
0.01 25V Ceramic
0.01 25V Ceramic
0.01 25V Ceramic

0.047 10V Ceramic

0.022 16V Ceramic


0.1 10V Ceramic

0.1 10V Ceramic


0.047 10V Ceramic
0.1 25V Ceramic
0.1 25V Ceramic
100 6.3V Electrolytic
0.1 25V Ceramic
0.1 25V Ceramic
0.1 25V Ceramic

0.1 25V Ceramic


0.1 25V Ceramic

0.1 25V Ceramic


0.1 25V Ceramic
0.1 25V Ceramic

12p 50V Ceramic


10p 50V Ceramic
0.1 25V Ceramic
0.1 25V Ceramic
0.1 25V Ceramic
0.1 25V Ceramic

0.1
0.1
0.1
0.1
0.1

25V
25V
25V
25V
25V

Ceramic
Ceramic
Ceramic
Ceramic
Ceramic

68 10V Electrolytic
1 10V Ceramic
1 10V Ceramic

0.1 10V Ceramic


0.1 10V Ceramic
0.1 25V Ceramic
0.1 10V Ceramic
4700p 50V Ceramic

1 10V Ceramic

0.01 25V Ceramic


0.1 25V Ceramic

LC-32/40/46LE600E/RU/S
NO.

PARTS CODE

PRICE NEW
RANK MARK

PART
DELIVERY

DESCRIPTION

[3] DUNTKF111FM11 (MAIN Unit)


C9614
C9615
C9616
C9618
C9619
C9620
C9621
C9622
C9624
C9625
C9626
C9627
C9628
C9629
C9630
C9631
C9632
C9633
C9634
C9635
C9636
C9638
C9639
C9640
C9641
C9642
C9643
C9644
C9645
C9646
C9647
C9649
C9651
C9652
C9653
C9654
C9655
C9656
C9657
C9658
C9659
C9666
C9667
C9668
C9669
C9673
C9674
D504
D505
D507
D508
D509
D510
D512
D513
D515
D516
D517
D518
D519
D520
D521
D522
D523
D524
D525
D528
D1101
D1102
D1301
D1508
D1509
D1510
D1513
D3306
D3308
D3309
D3310
D3311
D3312
D3313
D3314
D3315
D3316
D3317

RC-KZA616WJQZY
VCKYCZ1CB223KY
RC-KZA616WJQZY
RC-KZA616WJQZY
VCKYCZ1EB682KY
RC-KZA616WJQZY
VCKYCZ1EF104ZY
RC-KZA383WJZZY
VCKYCZ1EB682KY
RC-KZA114WJZZY
VCKYCZ1CB223KY
VCKYCZ1EB682KY
VCKYCZ1EB103KY
VCKYCZ1CB223KY
RC-KZA616WJQZY
VCKYCZ1EF104ZY
VCKYCZ1EB682KY
RC-KZA616WJQZY
RC-KZA383WJZZY
RC-KZA616WJQZY
VCKYCZ1EF104ZY
VCKYCZ1EF104ZY
RC-KZA114WJZZY
RC-KZA383WJZZY
RC-KZA114WJZZY
VCKYCZ1EB682KY
VCKYCZ1CB223KY
RC-KZA616WJQZY
VCKYCZ1EB682KY
RC-KZA510WJPZY
VCKYCZ1EF104ZY
RC-KZA383WJZZY
RC-KZA114WJZZY
RC-KZA114WJZZY
VCKYCZ1EF104ZY
VCAAPD1DJ476MY
VCCCCZ1HH101JY
VCKYCZ1HB102KY
VCCCCZ1HH101JY
VCCCCZ1HH101JY
VCCCCZ1HH101JY
RC-KZA616WJQZY
VCKYCZ1EF104ZY
VCKYCY1AB105KY
VCKYCZ1EF104ZY
VCKYCZ1EF104ZY
VCKYCY1AB105KY
RH-EXA512WJZZY
RH-EXA554WJZZY
RH-EXA523WJZZY
RH-EXA523WJZZY
RH-EXA523WJZZY
RH-EXA523WJZZY
VHDKDS184//-1Y
RH-EXA554WJZZY
RH-EXA523WJZZY
RH-EXA535WJZZY
RH-EXA535WJZZY
RH-EXA535WJZZY
RH-EXA535WJZZY
VHPGPFSV51V-1
RH-EXA520WJZZY
RH-EXA520WJZZY
VHDMAZ9120H-1Y
VHDMAZ9120H-1Y
RH-EXA523WJZZY
RH-EXA550WJZZY
RH-EXA535WJZZY
VHDMA111G++-1Y
VHDMA111G++-1Y
VHDKDS184//-1Y
VHDKDS184//-1Y
VHDKDS184//-1Y
VHDRB520S30-1Y
RH-EXA535WJZZY
VHD1SS226//-1Y
VHD1SS226//-1Y
RH-EXA520WJZZY
VHD1SS226//-1Y
RH-EXA520WJZZY
RH-EXA512WJZZY
RH-EXA512WJZZY
RH-EXA520WJZZY
RH-EXA512WJZZY
RH-EXA512WJZZY

AB
AC
AB
AB
AB
AB
AA
AC
AB
AB
AC
AB
AA
AC
AB
AA
AB
AB
AC
AB
AA
AA
AB
AC
AB
AB
AC
AB
AB
AB
AA
AC
AB
AB
AA
AF
AB
AB
AB
AB
AB
AB
AA
AB
AA
AA
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AM
AM
AM
AM
AG
AB
AB
AC
AC
AB
AB
AM
AA
AA
AB
AB
AB
AC
AM
AC
AC
AB
AC
AB
AB
AB
AB
AB
AB

J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J

Capacitor
Capacitor 0.022 16V Ceramic
Capacitor
Capacitor
Capacitor 6800p 25V Ceramic
Capacitor
Capacitor 0.1 25V Ceramic
Capacitor
Capacitor 6800p 25V Ceramic
Capacitor
Capacitor 0.022 16V Ceramic
Capacitor 6800p 25V Ceramic
Capacitor 0.01 25V Ceramic
Capacitor 0.022 16V Ceramic
Capacitor
Capacitor 0.1 25V Ceramic
Capacitor 6800p 25V Ceramic
Capacitor
Capacitor
Capacitor
Capacitor 0.1 25V Ceramic
Capacitor 0.1 25V Ceramic
Capacitor
Capacitor
Capacitor
Capacitor 6800p 25V Ceramic
Capacitor 0.022 16V Ceramic
Capacitor
Capacitor 6800p 25V Ceramic
Capacitor
Capacitor 0.1 25V Ceramic
Capacitor
Capacitor
Capacitor
Capacitor 0.1 25V Ceramic
Capacitor 47 20V Electrolytic
Capacitor 100p 50V Ceramic
Capacitor 1000p 50V Ceramic
Capacitor 100p 50V Ceramic
Capacitor 100p 50V Ceramic
Capacitor 100p 50V Ceramic
Capacitor
Capacitor 0.1 25V Ceramic
Capacitor 1 10V Ceramic
Capacitor 0.1 25V Ceramic
Capacitor 0.1 25V Ceramic
Capacitor 1 10V Ceramic
Zener Diode MAZ8039GHL
Zener Diode MAZ8150GML
Zener Diode MAZ8056GML
Zener Diode MAZ8056GML
Zener Diode MAZ8056GML
Zener Diode MAZ8056GML
Diode KDS184-RTK/P
Zener Diode MAZ8150GML
Zener Diode MAZ8056GML
Zener Diode MAZ8082GML
Zener Diode MAZ8082GML
Zener Diode MAZ8082GML
Zener Diode MAZ8082GML
Photo Diode
Zener Diode MAZ8051GML
Zener Diode MAZ8051GML
Diode MAZ9120H0L
Diode MAZ9120H0L
Zener Diode MAZ8056GML
Zener Diode MAZ8130GML
Zener Diode MAZ8082GML
Diode MA2J1110GL
Diode MA2J1110GL
Diode KDS184-RTK/P
Diode KDS184-RTK/P
Diode KDS184-RTK/P
Diode RB520S-30TE61
Zener Diode MAZ8082GML
Diode 1SS226(T5L,F,T)
Diode 1SS226(T5L,F,T)
Zener Diode MAZ8051GML
Diode 1SS226(T5L,F,T)
Zener Diode MAZ8051GML
Zener Diode MAZ8039GHL
Zener Diode MAZ8039GHL
Zener Diode MAZ8051GML
Zener Diode MAZ8039GHL
Zener Diode MAZ8039GHL

LC-32/40/46LE600E/RU/S
NO.

PARTS CODE

PRICE NEW
RANK MARK

PART
DELIVERY

DESCRIPTION

[3] DUNTKF111FM11 (MAIN Unit)


D3318
D3319
D3320
D3321
D3322
D3323
D3324
D9601
D9602
D9603
D9604
D9605
D9606
D9607
D9608
D9609
D9610
D9611
D9612
D9613
D9616
FB501
FB502
FB503
FB504
FB505
FB506
FB507
FB508
FB510
FB511
FB512
FB513
FB514
FB515
FB516
FB517
FB518
FB519
FB520
FB521
FB522
FB523
FB524
FB525
FB526
FB527
FB528
FB529
FB1504
FB2602
FB2604
FB2605
FB2606
FB2607
FB2608
FB2609
FB2610
FB2611
FB2612
FB2614
FB2616
FB2617
FB2623
FB3301
FB3302
FB3303
FB3304
FB3305
FB3306
FB3307
FB3308
FB3309
FB3310
FB3311
FB3312
FB3314
FB3315
FB3316
FB3317
FB3318
FB4401
FB4402
FB4403
FB4405

RH-EXA520WJZZY
RH-EXA512WJZZY
RH-EXA512WJZZY
RH-EXA512WJZZY
RH-PXA037WJZZY
RH-EXA512WJZZY
VHD1SS226//-1Y
VHDMA111G++-1Y
RH-EXA526WJZZY
VHDMA111G++-1Y
VHDMA111G++-1Y
RH-EXA514WJZZY
VHD1SS226//-1Y
VHDMA111G++-1Y
Not Available
VHDMA111G++-1Y
VHDRB056L40-1Y
VHDRB056L40-1Y
VHDRB056L40-1Y
VHDRB056L40-1Y
VHDMA111G++-1Y
RBLN-0077TAZZY
RBLN-0077TAZZY
RBLN-0077TAZZY
RBLN-0061TAZZY
RBLN-0061TAZZY
RBLN-0061TAZZY
RBLN-0061TAZZY
RBLN-0077TAZZY
RBLN-0077TAZZY
RBLN-0077TAZZY
RBLN-0077TAZZY
RBLN-0077TAZZY
RBLN-0077TAZZY
RBLN-0077TAZZY
RBLN-0077TAZZY
RBLN-0077TAZZY
RBLN-0077TAZZY
RBLN-0077TAZZY
RBLN-0077TAZZY
RBLN-0077TAZZY
RBLN-0077TAZZY
RBLN-0061TAZZY
RBLN-0077TAZZY
RBLN-0061TAZZY
RBLN-0077TAZZY
RBLN-0061TAZZY
RBLN-0077TAZZY
RBLN-0077TAZZY
RBLN-A192WJZZY
RBLN-A375WJQZY
RBLN-A375WJQZY
RBLN-A375WJQZY
RBLN-A375WJQZY
RBLN-A375WJQZY
RBLN-A375WJQZY
RBLN-0077TAZZY
RBLN-0077TAZZY
RBLN-0077TAZZY
RBLN-0077TAZZY
RBLN-0077TAZZY
RBLN-0077TAZZY
RBLN-0077TAZZY
RBLN-0077TAZZY
RBLN-0061TAZZY
RBLN-0061TAZZY
RBLN-A192WJZZY
RBLN-0061TAZZY
RBLN-0061TAZZY
RBLN-0061TAZZY
RBLN-A188WJZZY
RBLN-0061TAZZY
RBLN-A188WJZZY
RBLN-0061TAZZY
RBLN-A188WJZZY
RBLN-0061TAZZY
RBLN-A188WJZZY
RBLN-A188WJZZY
RBLN-A188WJZZY
RBLN-A188WJZZY
RBLN-A192WJZZY
RBLN-A192WJZZY
RBLN-A192WJZZY
RBLN-A192WJZZY
RBLN-A192WJZZY

AB
AB
AB
AB
AB
AB
AC
AA
AB
AA
AA
AB
AC
AA
AA
AC
AC
AC
AC
AA
AB
AB
AB
AD
AD
AD
AD
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AD
AB
AD
AB
AD
AB
AB
AA
AA
AA
AA
AA
AA
AA
AB
AB
AB
AB
AB
AB
AB
AB
AD
AD
AA
AD
AD
AD
AA
AD
AA
AD
AA
AD
AA
AA
AA
AA
AA
AA
AA
AA
AA

J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J

Zener Diode MAZ8051GML


Zener Diode MAZ8039GHL
Zener Diode MAZ8039GHL
Zener Diode MAZ8039GHL
Zener Diode SML-310MTT86
Zener Diode MAZ8039GHL
Diode 1SS226(T5L,F,T)
Diode MA2J1110GL
Zener Diode MAZ8062GML
Diode MA2J1110GL
Diode MA2J1110GL
Zener Diode MAZ8043GML
Diode 1SS226(T5L,F,T)
Diode MA2J1110GL
Zener Diode *PWB replacement item
Diode MA2J1110GL
Diode RB056L-40TE25
Diode RB056L-40TE25
Diode RB056L-40TE25
Diode RB056L-40TE25
Diode MA2J1110GL
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core

LC-32/40/46LE600E/RU/S
NO.

PARTS CODE

PRICE NEW
RANK MARK

PART
DELIVERY

DESCRIPTION

[3] DUNTKF111FM11 (MAIN Unit)


FB4406
FB9601
FB9610
FB9611
FB9614
FB9615
FB9616
FB9617
FB9618
FL501
FL502
FL503
FL504
FL507
FL508
FL509
FL510
FL511
FL512
FL513
FL514
FL515
FL516
FL517
FL3301
FL3302
FL3303
FL3304
FL3501
FL3502
IC501
IC503
IC504
IC506
IC507
IC508
IC1104
IC1301
IC1302
IC1303
IC1508
IC2602
IC2701
IC3302
IC3303
IC3304
IC3305
IC3501
IC3502
IC4401
IC4402
IC8401
IC8403
IC8455
IC9601
IC9603
IC9604
IC9605
IC9606
IC9608
IC9610
IC9611
IC9612
IC9613
IC9614
J501
J502
J503
J504
J505
J506
J3301
L501
L502
L503
L504
L1102
L1103
L1104
L1301
L1302
L2613
L2614
L2615
L2616

RBLN-A192WJZZY
Not Available
RBLN-0207TAZZY
RBLN-0207TAZZY
Not Available
RBLN-0207TAZZY
RBLN-0207TAZZY
RBLN-0207TAZZY
RBLN-0207TAZZY
RFILN0003TAZZY
RFILN0003TAZZY
RFILN0003TAZZY
RFILN0017TAZZY
RFILN0017TAZZY
RFILN0017TAZZY
RFILN0017TAZZY
RFILN0017TAZZY
RFILN0017TAZZY
RFILN0017TAZZY
RFILN0017TAZZY
RFILN0003TAZZY
RFILN0003TAZZY
RFILN0003TAZZY
RFILN0017TAZZY
RFILNA119WJZZY
RFILNA119WJZZY
RFILNA119WJZZY
RFILNA119WJZZY
RFILNA119WJZZY
RFILNA119WJZZY
RH-IXC206WJQZS
VHIT7SET08U1EY
VHIMM1506XN-1Y
VHIM3221EIP-1Y
VHIMM1507XN-1Y
VHIMM1756AU-1Y
VHIPQ1LA505-1Y
VHIAK4341ED-1Y
VHIMT8292N+-1Q
VHIS80944NM-1Y
VHISII91873-1Q
VHIHC2G66DP-1Y
VHIYDA148QZ-1Y
VHIBD6538G+-1Y
RH-IXC758WJQZQ
Not Available
Not Available
RH-IXC505WJQZQ
RH-IXC505WJQZQ
VHIMT8295AE-1Q
VHIAOZ1320C-1Y
RH-IXC721WJQZQ
Not Available
Not Available
VHIHC2G66DP-1Y
VHIMM3141YN-1Y
Not Available
VHILV5893M+-1Y
VHILV5805M+-1Y
VHILV5893M+-1Y
VHIPQ1LAX95-1Y
VHITCR5SB25-1Y
VHITCR5SB33-1Y
VHIHC2G66DP-1Y
Not Available
QJAKJ0008GEZZ
QJAKFA061WJZZ
QJAKGA131WJZZ
QJAKJ0047CEZZ
QJAKGA079WJZZ
QJAKFA061WJZZ
QSOCZA172WJQZ
VPCNN120J1R9NY
VPCNN120J1R9NY
VPCNN2R2JR77NY
VPCNN2R2JR77NY
VPSBN2R2JR54NY
VPSBN100J1R2NY
VPSBN2R2JR54NY
VPSBN2R2JR54NY
VPSBN2R2JR54NY
RCILFA119WJZZY
RCILFA119WJZZY
RCILFA119WJZZY
RCILFA119WJZZY

AA
AB
AB
AB
AB
AB
AB
AD
AD
AD
AC
AC
AC
AC
AC
AC
AC
AC
AD
AD
AD
AC
AC
AC
AC
AC
AC
AC
AC
AD
AK
AD
AD
AC
AF
AK
AC
AN
AD
AL
AD
BF
AY
AY
AM
AE
AR
AD
AC
AE
AG
AE
AD
AD
AC
AD
AD
AE
AG
AD
AD
AE
AD
AB
AB
AB
AB
AB
AB
AB
AB
AB
AE
AE
AE
AE

J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
P
P
J
P
J
J
J
P
J
J
P
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J

Ferrite Core
Ferrite Core *PWB replacement item
Ferrite Core
Ferrite Core
Ferrite Core *PWB replacement item
Ferrite Core
Ferrite Core
Ferrite Core
Ferrite Core
Filter
Filter
Filter
Filter
Filter
Filter
Filter
Filter
Filter
Filter
Filter
Filter
Filter
Filter
Filter
Filter
Filter
Filter
Filter
Filter
Filter
IC EDID (PC)
IC TC7SET08FU(5L,JF,T
IC MM1506XNRE
IC MAX3221EIPWR
IC MM1507XNRE
IC MM1756AURE
IC PQ1LA505MSPQ
IC AK4341ETD
IC MT8292N
IC S-80944CNMC-G9ET2G
IC SiI9187ACNU
IC 74HC2G66DP,125
IC YDA148-QZE2
IC BD6538G-TR
IC MT5362ANG-B
IC *PWB replacement item
IC *PWB replacement item
IC K4T51163QG-HCF7
IC K4T51163QG-HCF7
IC MT8295AE
IC AOZ1320CI-04
IC HY27US08121B-TPCB
IC *PWB replacement item
IC * PWB replacement item
IC 74HC2G66DP,125
IC MM3141YNRE
IC *PWB replacement item
IC LV5893M-TE-L-E
IC LV5805M-TE-L-E
IC LV5893M-TE-L-E
IC PQ1LAX95MSPQ
IC TCR5SB25(TE85L,F)
IC TCR5SB33(TE85L,F)
IC 74HC2G66DP,125
IC *PWB replacement item
Jack
Jack
Jack
Jack
Jack
Jack
Socket
Peaking Coil 12H
Peaking Coil 12H
Peaking Coil 2.2H
Peaking Coil 2.2H
Peaking Coil 2.2H
Peaking Coil 10H
Peaking Coil 2.2H
Peaking Coil 2.2H
Peaking Coil 2.2H
Coil
Coil
Coil
Coil

LC-32/40/46LE600E/RU/S
NO.

PARTS CODE

PRICE NEW
RANK MARK

PART
DELIVERY

DESCRIPTION

[3] DUNTKF111FM11 (MAIN Unit)


L2617
L2618
L2701
L2702
L2703
L2704
L3301
L9601
L9602
L9603
L9604
LUG9602
LUG9603
LUG9605
LUG9609
LUG9610
LUG9611
LUG9612
P2601
P2602
P2701
P3302
P9601
P9602
Q501
Q502
Q503
Q504
Q505
Q506
Q507
Q508
Q509
Q1101
Q1102
Q1105
Q1106
Q1301
Q1508
Q1509
Q2701
Q9601
Q9602
Q9607
Q9608
R504
R505
R506
R507
R508
R511
R512
R513
R514
R515
R516
R517
R518
R519
R520
R522
R523
R524
R530
R531
R533
R535
R537
R538
R541
R544
R547
R549
R551
R552
R553
R554
R555
R556
R557
R558
R559
R560
R561
R562

RCILFA119WJZZY
RCILFA119WJZZY
RCILPA899WJZZY
RCILPA899WJZZY
RCILPA899WJZZY
RCILPA899WJZZY
RCILFA228WJZZY
RCILPA758WJQZY
RCILPA899WJZZY
RCILPA760WJQZY
RCILPA899WJZZY
QLUGHA009WJZZY
QLUGHA009WJZZY
QLUGHA009WJZZY
QLUGHA009WJZZY
QLUGHA009WJZZY
QLUGHA009WJZZY
QLUGHA009WJZZY
QCNCWA671WJQZY
QPLGNA349WJZZY
QPLGNA173WJZZY
QPLGNA333WJZZY
QPLGNA168WJZZY
QPLGNA328WJZZY
VSIMH23T110-1Y
VSIMH23T110-1Y
VS2SA1530AR-1Y
VS2SA1530AR-1Y
VSLTC144EEB-1Y
VSIMH23T110-1Y
VS2SA1530AR-1Y
VS2SA1530AR-1Y
VSIMH23T110-1Y
VS2SC3928AR-1Y
VS2SA1530AR-1Y
RH-TXA026WJZZY
VSLTA124EEB-1Y
VS2SC3928AR-1Y
VSKTA1535T+-1Y
VSKRC402E++-1Y
VSDTC614TK+-1Y
VSLTC144EEB-1Y
VSLTA124EEB-1Y
VS2SC3928AR-1Y
VSLTA124EEB-1Y
VRS-CZ1JF222FY
VRS-TQ2EF750JY
VRS-TQ2EF750JY
VRS-TQ2EF750JY
VRS-CZ1JF682FY
VRS-CZ1JF102JY
VRS-CZ1JF102JY
VRS-TQ2EF680JY
VRS-CZ1JF104JY
VRS-CZ1JF222FY
VRS-TQ2EF101JY
VRS-CZ1JF104JY
VRS-TQ2EF680JY
VRS-TQ2EF750JY
VRS-CZ1JF682FY
VRS-CZ1JF561JY
VRS-CZ1JF102JY
VRS-CZ1JF102JY
VRS-TQ2EF750JY
VRS-TQ2EF750JY
VRS-CZ1JF561JY
VRS-TQ2EF750JY
VRS-TQ2EF750JY
VRK-SA1JF472JY
VRS-TQ2EF750JY
VRS-TQ2EF750JY
VRK-SB1FF101JY
VRS-CZ1JF102JY
VRS-CZ1JF102JY
VRS-TV1JD221JY
VRS-TV1JD221JY
VRS-CZ1JF104JY
VRS-CZ1JF104JY
VRS-TV1JD221JY
VRS-CZ1JF102JY
VRS-CZ1JF102JY
VRS-TV1JD221JY
VRS-CZ1JF104JY
VRS-CZ1JF104JY
VRS-CZ1JF104JY

AE
AE
AC
AC
AC
AC
AD
AC
AC
AD
AC
AC
AC
AC
AC
AC
AC
AC
AH
AE
AD
AD
AF
AD
AC
AC
AB
AB
AA
AC
AB
AB
AC
AB
AB
AD
AA
AB
AC
AB
AB
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA

J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J

Coil
Coil
Coil
Coil
Coil
Coil
Coil
Coil
Coil
Coil
Coil
Ground Part
Ground Part
Ground Part
Ground Part
Ground Part
Ground Part
Ground Part
Connector
Plug
Plug
Plug
Plug
Plug
Transistor IMH23T110
Transistor IMH23T110
Transistor 2SA1530A-T112-1R
Transistor 2SA1530A-T112-1R
Transistor LTC144EEBFS8TL
Transistor IMH23T110
Transistor 2SA1530A-T112-1R
Transistor 2SA1530A-T112-1R
Transistor IMH23T110
Transistor 2SC3928A-T112-1R
Transistor 2SA1530A-T112-1R
Transistor PBLS2001D,115
Transistor LTA124EEBFS8TL
Transistor 2SC3928A-T112-1R
Transistor KTA1535T-RTK/P
Transistor
Transistor DTC614TKT146
Transistor LTC144EEBFS8TL
Transistor LTA124EEBFS8TL
Transistor 2SC3928A-T112-1R
Transistor LTA124EEBFS8TL
Resistor 2.2k 1/16W Metal Oxide
Resistor 75 1/4W Metal Oxide
Resistor 75 1/4W Metal Oxide
Resistor 75 1/4W Metal Oxide
Resistor 6.8k 1/16W Metal Oxide
Resistor 1k 1/16W Metal Oxide
Resistor 1k 1/16W Metal Oxide
Resistor 68 1/4W Metal Oxide
Resistor 100k 1/16W Metal Oxide
Resistor 2.2k 1/16W Metal Oxide
Resistor 100 1/4W Metal Oxide
Resistor 100k 1/16W Metal Oxide
Resistor 68 1/4W Metal Oxide
Resistor 75 1/4W Metal Oxide
Resistor 6.8k 1/16W Metal Oxide
Resistor 560 1/16W Metal Oxide
Resistor 1k 1/16W Metal Oxide
Resistor 1k 1/16W Metal Oxide
Resistor 75 1/4W Metal Oxide
Resistor 75 1/4W Metal Oxide
Resistor 560 1/16W Metal Oxide
Resistor 75 1/4W Metal Oxide
Resistor 75 1/4W Metal Oxide
Resistor 4.7k 1/16W Metal Composition
Resistor 75 1/4W Metal Oxide
Resistor 75 1/4W Metal Oxide
Resistor 100 1/32W Metal Composition
Resistor 1k 1/16W Metal Oxide
Resistor 1k 1/16W Metal Oxide
Resistor 220 1/16W Metal Oxide
Resistor 220 1/16W Metal Oxide
Resistor 100k 1/16W Metal Oxide
Resistor 100k 1/16W Metal Oxide
Resistor 220 1/16W Metal Oxide
Resistor 1k 1/16W Metal Oxide
Resistor 1k 1/16W Metal Oxide
Resistor 220 1/16W Metal Oxide
Resistor 100k 1/16W Metal Oxide
Resistor 100k 1/16W Metal Oxide
Resistor 100k 1/16W Metal Oxide

LC-32/40/46LE600E/RU/S
NO.

PARTS CODE

PRICE NEW
RANK MARK

PART
DELIVERY

DESCRIPTION

[3] DUNTKF111FM11 (MAIN Unit)


R563
R564
R565
R566
R567
R568
R569
R570
R571
R572
R573
R574
R575
R576
R577
R578
R579
R580
R581
R582
R584
R586
R588
R589
R590
R591
R592
R593
R594
R595
R597
R599
R600
R601
R602
R603
R604
R605
R606
R607
R608
R609
R610
R611
R612
R613
R614
R615
R616
R617
R618
R619
R620
R621
R622
R623
R624
R625
R626
R629
R630
R631
R633
R635
R636
R639
R640
R1102
R1103
R1109
R1110
R1112
R1113
R1114
R1115
R1118
R1120
R1121
R1122
R1123
R1124
R1125
R1126
R1127
R1128

VRS-CZ1JF104JY
VRS-CZ1JF102JY
VRS-CZ1JF102JY
VRS-CZ1JF564JY
VRS-CZ1JF104JY
VRS-CZ1JF104JY
VRS-CZ1JF564JY
VRS-CZ1JF564JY
VRS-CZ1JF564JY
VRK-SA1JF331JY
VRK-SA1JF331JY
VRS-CZ1JF104JY
VRS-CZ1JF102JY
VRS-CZ1JF102JY
VRK-SA1JF272JY
VRS-CZ1JF102JY
VRS-CZ1JF102JY
VRS-CZ1JF104JY
VRS-CZ1JF101JY
VRS-CZ1JF472JY
VRS-TQ2EF560JY
VRS-TQ2EF560JY
VRS-CZ1JF102JY
VRS-TQ2EF560JY
VRS-TW2ED101JY
VRS-CZ1JF104JY
VRS-CZ1JF101JY
VRS-TW2ED101JY
VRS-CZ1JF104JY
VRS-CZ1JF472JY
VRS-CZ1JF101JY
VRS-TQ2EF750JY
VRS-CZ1JF104JY
VRS-CY1JF000JY
VRS-CZ1JF473JY
VRS-CY1JF000JY
VRS-CZ1JF103JY
VRS-CZ1JF104JY
VRS-TW2ED101JY
VRS-TW2ED101JY
VRS-TV1JD101JY
VRS-TV1JD101JY
VRS-CZ1JF104JY
VRS-CZ1JF221JY
VRS-CZ1JF561JY
VRS-TV1JD101JY
VRS-CZ1JF102JY
VRS-CZ1JF470JY
VRS-CZ1JF104JY
VRS-CZ1JF221JY
VRS-CZ1JF561JY
VRS-CZ1JF102JY
VRS-CZ1JF103JY
VRS-CZ1JF564JY
VRS-CZ1JF564JY
VRS-CZ1JF472JY
VRS-CZ1JF472JY
VRS-CZ1JF102JY
VRS-CZ1JF101JY
VRS-CZ1JF180JY
VRS-CZ1JF180JY
VRS-CZ1JF180JY
VRS-CY1JF000JY
VRS-CY1JF000JY
VRS-CY1JF000JY
VRS-CZ1JF221JY
VRS-CZ1JF472JY
VRK-SA1JF101JY
VRS-CZ1JF000JY
VRS-CZ1JF103JY
VRS-CZ1JF392JY
VRS-CZ1JF391JY
VRS-CZ1JF151JY
VRS-CZ1JF100JY
VRS-CZ1JF391JY
VRK-SA1JF472JY
VRS-CZ1JF103JY
VRS-CZ1JF103JY
VRS-CZ1JF273JY
VRS-CZ1JF273JY
VRS-CZ1JF273JY
VRS-CZ1JF273JY
VRS-CZ1JF273JY
VRS-CZ1JF273JY
VRS-CZ1JF273JY

AA
AA
AA
AB
AA
AA
AB
AB
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AC
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA

J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J

Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor

10

100k 1/16W Metal Oxide


1k 1/16W Metal Oxide
1k 1/16W Metal Oxide
560k 1/16W Metal Oxide
100k 1/16W Metal Oxide
100k 1/16W Metal Oxide
560k 1/16W Metal Oxide
560k 1/16W Metal Oxide
560k 1/16W Metal Oxide
330 1/16W Metal Composition
330 1/16W Metal Composition
100k 1/16W Metal Oxide
1k 1/16W Metal Oxide
1k 1/16W Metal Oxide
2.7k 1/16W Metal Composition
1k 1/16W Metal Oxide
1k 1/16W Metal Oxide
100k 1/16W Metal Oxide
100 1/16W Metal Oxide
4.7k 1/16W Metal Oxide
56 1/4W Metal Oxide
56 1/4W Metal Oxide
1k 1/16W Metal Oxide
56 1/4W Metal Oxide
100 1/4W Metal Oxide
100k 1/16W Metal Oxide
100 1/16W Metal Oxide
100 1/4W Metal Oxide
100k 1/16W Metal Oxide
4.7k 1/16W Metal Oxide
100 1/16W Metal Oxide
75 1/4W Metal Oxide
100k 1/16W Metal Oxide
0 1/16W Metal Oxide
47k 1/16W Metal Oxide
0 1/16W Metal Oxide
10k 1/16W Metal Oxide
100k 1/16W Metal Oxide
100 1/4W Metal Oxide
100 1/4W Metal Oxide
100 1/16W Metal Oxide
100 1/16W Metal Oxide
100k 1/16W Metal Oxide
220 1/16W Metal Oxide
560 1/16W Metal Oxide
100 1/16W Metal Oxide
1k 1/16W Metal Oxide
47 1/16W Metal Oxide
100k 1/16W Metal Oxide
220 1/16W Metal Oxide
560 1/16W Metal Oxide
1k 1/16W Metal Oxide
10k 1/16W Metal Oxide
560k 1/16W Metal Oxide
560k 1/16W Metal Oxide
4.7k 1/16W Metal Oxide
4.7k 1/16W Metal Oxide
1k 1/16W Metal Oxide
100 1/16W Metal Oxide
18 1/16W Metal Oxide
18 1/16W Metal Oxide
18 1/16W Metal Oxide
0 1/16W Metal Oxide
0 1/16W Metal Oxide
0 1/16W Metal Oxide
220 1/16W Metal Oxide
4.7k 1/16W Metal Oxide
100 1/16W Metal Composition
0 1/16W Metal Oxide
10k 1/16W Metal Oxide
3.9k 1/16W Metal Oxide
390 1/16W Metal Oxide
150 1/16W Metal Oxide
10 1/16W Metal Oxide
390 1/16W Metal Oxide
4.7k 1/16W Metal Composition
10k 1/16W Metal Oxide
10k 1/16W Metal Oxide
27k 1/16W Metal Oxide
27k 1/16W Metal Oxide
27k 1/16W Metal Oxide
27k 1/16W Metal Oxide
27k 1/16W Metal Oxide
27k 1/16W Metal Oxide
27k 1/16W Metal Oxide

LC-32/40/46LE600E/RU/S
NO.

PARTS CODE

PRICE NEW
RANK MARK

PART
DELIVERY

DESCRIPTION

[3] DUNTKF111FM11 (MAIN Unit)


R1129
R1130
R1131
R1143
R1144
R1145
R1152
R1153
R1154
R1155
R1157
R1301
R1302
R1304
R1305
R1306
R1307
R1308
R1309
R1310
R1311
R1312
R1313
R1314
R1315
R1316
R1317
R1318
R1319
R1336
R1337
R1338
R1339
R1507
R1508
R1509
R1510
R1515
R1520
R1523
R1538
R1539
R1544
R1545
R1547
R1548
R1549
R1550
R1551
R1552
R1554
R1555
R1556
R1564
R1565
R1567
R1569
R1570
R1572
R1573
R1574
R1575
R2607
R2608
R2609
R2610
R2611
R2612
R2636
R2639
R2702
R2710
R2711
R2712
R2713
R2714
R2716
R2718
R2720
R2721
R2722
R2723
R2725
R2726
R2727

VRS-CZ1JF273JY
VRS-CZ1JF273JY
VRS-CZ1JF273JY
VRS-CZ1JF472JY
VRS-CZ1JF000JY
VRS-CZ1JF000JY
VRS-CZ1JF000JY
VRS-CZ1JF000JY
VRS-CZ1JF561JY
VRS-CZ1JF103JY
VRS-CZ1JF000JY
VRS-CZ1JF102JY
VRS-CZ1JF103JY
VRS-CZ1JF103JY
VRS-CZ1JF103JY
VRS-CZ1JF000JY
VRS-CZ1JF000JY
VRS-CZ1JF391JY
VRS-CZ1JF391JY
VRS-CZ1JF391JY
VRS-CZ1JF391JY
VRS-CZ1JF391JY
VRS-CZ1JF391JY
VRS-CZ1JF473JY
VRS-CZ1JF473JY
VRS-CZ1JF473JY
VRS-CZ1JF473JY
VRS-CZ1JF473JY
VRS-CZ1JF473JY
VRS-CZ1JF153JY
VRS-CZ1JF123JY
VRS-CZ1JF103JY
VRS-CZ1JF102JY
VRS-CZ1JF273JY
VRK-SA1JF473JY
VRK-SA1JF473JY
VRK-SA1JF473JY
VRS-CZ1JF000JY
VRS-CZ1JF000JY
VRS-CZ1JF000JY
VRS-CZ1JF331JY
VRS-CZ1JF103JY
VRK-SA1JF473JY
VRK-SA1JF100JY
VRS-CZ1JF103JY
VRS-CZ1JF472JY
VRS-CZ1JF222JY
VRS-CZ1JF100JY
VRS-CZ1JF332JY
VRS-CZ1JF332JY
VRK-SA1JF100JY
VRK-SA1JF100JY
VRK-SA1JF473JY
VRS-CZ1JF103JY
VRS-CZ1JF103JY
VRS-CZ1JF332JY
VRS-CZ1JF100JY
VRK-SA1JF100JY
VRS-CZ1JF332JY
VRS-CZ1JF100JY
VRS-CZ1JF103JY
VRS-CZ1JF100JY
VRS-CZ1JF103JY
VRS-CZ1JF103JY
VRS-CZ1JF103JY
VRS-CZ1JF103JY
VRS-CZ1JF470JY
VRS-CZ1JF103JY
VRS-CZ1JF104JY
VRS-CZ1JF104JY
VRK-SA1JF331JY
VRK-SA1JF103JY
VRS-CZ1JF274FY
VRS-CZ1JF104FY
VRS-CZ1JF000JY
VRS-CZ1JF474JY
VRS-CZ1JF103JY
VRS-CZ1JF562JY
VRS-TV1JD000JY
VRS-TV1JD000JY
VRS-TV1JD000JY
VRS-TV1JD000JY
VRS-CZ1JF224JY
VRS-CZ1JF103JY
VRS-CZ1JF472JY

AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AC
AC
AC
AA
AA
AA
AA
AA
AC
AB
AA
AA
AA
AA
AA
AA
AB
AB
AC
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA

J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J

Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor

11

27k 1/16W Metal Oxide


27k 1/16W Metal Oxide
27k 1/16W Metal Oxide
4.7k 1/16W Metal Oxide
0 1/16W Metal Oxide
0 1/16W Metal Oxide
0 1/16W Metal Oxide
0 1/16W Metal Oxide
560 1/16W Metal Oxide
10k 1/16W Metal Oxide
0 1/16W Metal Oxide
1k 1/16W Metal Oxide
10k 1/16W Metal Oxide
10k 1/16W Metal Oxide
10k 1/16W Metal Oxide
0 1/16W Metal Oxide
0 1/16W Metal Oxide
390 1/16W Metal Oxide
390 1/16W Metal Oxide
390 1/16W Metal Oxide
390 1/16W Metal Oxide
390 1/16W Metal Oxide
390 1/16W Metal Oxide
47k 1/16W Metal Oxide
47k 1/16W Metal Oxide
47k 1/16W Metal Oxide
47k 1/16W Metal Oxide
47k 1/16W Metal Oxide
47k 1/16W Metal Oxide
15k 1/16W Metal Oxide
12k 1/16W Metal Oxide
10k 1/16W Metal Oxide
1k 1/16W Metal Oxide
27k 1/16W Metal Oxide
47k 1/16W Metal Composition
47k 1/16W Metal Composition
47k 1/16W Metal Composition
0 1/16W Metal Oxide
0 1/16W Metal Oxide
0 1/16W Metal Oxide
330 1/16W Metal Oxide
10k 1/16W Metal Oxide
47k 1/16W Metal Composition
10 1/16W Metal Composition
10k 1/16W Metal Oxide
4.7k 1/16W Metal Oxide
2.2k 1/16W Metal Oxide
10 1/16W Metal Oxide
3.3k 1/16W Metal Oxide
3.3k 1/16W Metal Oxide
10 1/16W Metal Composition
10 1/16W Metal Composition
47k 1/16W Metal Composition
10k 1/16W Metal Oxide
10k 1/16W Metal Oxide
3.3k 1/16W Metal Oxide
10 1/16W Metal Oxide
10 1/16W Metal Composition
3.3k 1/16W Metal Oxide
10 1/16W Metal Oxide
10k 1/16W Metal Oxide
10 1/16W Metal Oxide
10k 1/16W Metal Oxide
10k 1/16W Metal Oxide
10k 1/16W Metal Oxide
10k 1/16W Metal Oxide
47 1/16W Metal Oxide
10k 1/16W Metal Oxide
100k 1/16W Metal Oxide
100k 1/16W Metal Oxide
330 1/16W Metal Composition
10k 1/16W Metal Composition
270k 1/16W Metal Oxide
100k 1/16W Metal Oxide
0 1/16W Metal Oxide
470k 1/16W Metal Oxide
10k 1/16W Metal Oxide
5.6k 1/16W Metal Oxide
0 1/16W Metal Oxide
0 1/16W Metal Oxide
0 1/16W Metal Oxide
0 1/16W Metal Oxide
220k 1/16W Metal Oxide
10k 1/16W Metal Oxide
4.7k 1/16W Metal Oxide

LC-32/40/46LE600E/RU/S
NO.

PARTS CODE

PRICE NEW
RANK MARK

PART
DELIVERY

DESCRIPTION

[3] DUNTKF111FM11 (MAIN Unit)


R2728
R3302
R3304
R3306
R3308
R3309
R3310
R3312
R3313
R3314
R3315
R3317
R3318
R3319
R3320
R3321
R3322
R3323
R3324
R3325
R3326
R3327
R3328
R3329
R3330
R3333
R3334
R3339
R3340
R3341
R3342
R3343
R3344
R3346
R3348
R3350
R3352
R3353
R3355
R3356
R3357
R3360
R3361
R3362
R3363
R3364
R3365
R3366
R3367
R3368
R3369
R3370
R3371
R3372
R3373
R3374
R3376
R3377
R3378
R3379
R3380
R3381
R3382
R3383
R3384
R3385
R3386
R3388
R3389
R3390
R3391
R3392
R3393
R3394
R3395
R3396
R3397
R3398
R3400
R3401
R3402
R3404
R3405
R3407
R3408

VRK-SA1JF473JY
VRS-CZ1JF102FY
VRS-CZ1JF393FY
VRS-CZ1JF000JY
VRS-CZ1JF103FY
VRS-CZ1JF333FY
VRS-CZ1JF333FY
VRS-CZ1JF102FY
VRS-CZ1JF102FY
VRS-CZ1JF102FY
VRS-CZ1JF103JY
VRS-CZ1JF101JY
VRS-CZ1JF512FY
VRS-CZ1JF330JY
VRS-CZ1JF330JY
VRS-CZ1JF470JY
VRS-CZ1JF1R0JY
VRS-CZ1JF470JY
VRS-CZ1JF470JY
VRS-CZ1JF561FY
VRS-CZ1JF470JY
VRS-CZ1JF000JY
VRS-CZ1JF470JY
VRS-CZ1JF103JY
VRS-CZ1JF470JY
VRS-CZ1JF470JY
VRS-CZ1JF472JY
VRS-CZ1JF105JY
VRS-CZ1JF391JY
VRS-CZ1JF390JY
VRS-CZ1JF390JY
VRK-SB1FF470JY
VRS-CZ1JF472JY
VRS-CZ1JF472JY
VRS-CZ1JF472JY
VRS-CZ1JF472JY
VRS-CZ1JF472JY
VRS-CZ1JF103JY
VRS-CZ1JF472JY
VRK-SA1JF472JY
VRS-CZ1JF472JY
VRS-CZ1JF472JY
VRS-CZ1JF103JY
VRS-CZ1JF680JY
VRS-CZ1JF680JY
VRS-CZ1JF680JY
VRS-CZ1JF101JY
VRS-CZ1JF101JY
VRS-CZ1JF101JY
VRS-CZ1JF101JY
VRS-CZ1JF680JY
VRS-CZ1JF680JY
VRS-CZ1JF680JY
VRS-CZ1JF000JY
VRS-CZ1JF273JY
VRS-CZ1JF000JY
VRS-CZ1JF101JY
VRS-CZ1JF101JY
VRS-CZ1JF101JY
VRS-CZ1JF470JY
VRS-CZ1JF470JY
VRS-CZ1JF470JY
VRS-CZ1JF470JY
VRS-CZ1JF470JY
VRS-CZ1JF470JY
VRS-CZ1JF101JY
VRS-CZ1JF103JY
VRS-CZ1JF680JY
VRS-CZ1JF680JY
VRS-CZ1JF680JY
VRS-CZ1JF470JY
VRS-CZ1JF470JY
VRS-CZ1JF470JY
VRS-CZ1JF470JY
VRS-CZ1JF470JY
VRS-CZ1JF470JY
VRS-CZ1JF470JY
VRS-CZ1JF101JY
VRS-CZ1JF472JY
VRS-CZ1JF472JY
VRS-CZ1JF472JY
VRS-CZ1JF472JY
VRS-CZ1JF472JY
VRS-CZ1JF102JY
VRS-CZ1JF220JY

AC
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AB
AB
AA
AA
AA
AA
AB
AB
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AB
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA

J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J

Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor

12

47k 1/16W Metal Composition


1k 1/16W Metal Oxide
39k 1/16W Metal Oxide
0 1/16W Metal Oxide
10k 1/16W Metal Oxide
33k 1/16W Metal Oxide
33k 1/16W Metal Oxide
1k 1/16W Metal Oxide
1k 1/16W Metal Oxide
1k 1/16W Metal Oxide
10k 1/16W Metal Oxide
100 1/16W Metal Oxide
5.1k 1/16W Metal Oxide
33 1/16W Metal Oxide
33 1/16W Metal Oxide
47 1/16W Metal Oxide
1 1/16W Metal Oxide
47 1/16W Metal Oxide
47 1/16W Metal Oxide
560 1/16W Metal Oxide
47 1/16W Metal Oxide
0 1/16W Metal Oxide
47 1/16W Metal Oxide
10k 1/16W Metal Oxide
47 1/16W Metal Oxide
47 1/16W Metal Oxide
4.7k 1/16W Metal Oxide
1M 1/16W Metal Oxide
390 1/16W Metal Oxide
39 1/16W Metal Oxide
39 1/16W Metal Oxide
47 1/32W Metal Composition
4.7k 1/16W Metal Oxide
4.7k 1/16W Metal Oxide
4.7k 1/16W Metal Oxide
4.7k 1/16W Metal Oxide
4.7k 1/16W Metal Oxide
10k 1/16W Metal Oxide
4.7k 1/16W Metal Oxide
4.7k 1/16W Metal Composition
4.7k 1/16W Metal Oxide
4.7k 1/16W Metal Oxide
10k 1/16W Metal Oxide
68 1/16W Metal Oxide
68 1/16W Metal Oxide
68 1/16W Metal Oxide
100 1/16W Metal Oxide
100 1/16W Metal Oxide
100 1/16W Metal Oxide
100 1/16W Metal Oxide
68 1/16W Metal Oxide
68 1/16W Metal Oxide
68 1/16W Metal Oxide
0 1/16W Metal Oxide
27k 1/16W Metal Oxide
0 1/16W Metal Oxide
100 1/16W Metal Oxide
100 1/16W Metal Oxide
100 1/16W Metal Oxide
47 1/16W Metal Oxide
47 1/16W Metal Oxide
47 1/16W Metal Oxide
47 1/16W Metal Oxide
47 1/16W Metal Oxide
47 1/16W Metal Oxide
100 1/16W Metal Oxide
10k 1/16W Metal Oxide
68 1/16W Metal Oxide
68 1/16W Metal Oxide
68 1/16W Metal Oxide
47 1/16W Metal Oxide
47 1/16W Metal Oxide
47 1/16W Metal Oxide
47 1/16W Metal Oxide
47 1/16W Metal Oxide
47 1/16W Metal Oxide
47 1/16W Metal Oxide
100 1/16W Metal Oxide
4.7k 1/16W Metal Oxide
4.7k 1/16W Metal Oxide
4.7k 1/16W Metal Oxide
4.7k 1/16W Metal Oxide
4.7k 1/16W Metal Oxide
1k 1/16W Metal Oxide
22 1/16W Metal Oxide

LC-32/40/46LE600E/RU/S
NO.

PARTS CODE

PRICE NEW
RANK MARK

PART
DELIVERY

DESCRIPTION

[3] DUNTKF111FM11 (MAIN Unit)


R3409
R3410
R3501
R3502
R3504
R3505
R3506
R3507
R3508
R3509
R3510
R3513
R3514
R3515
R3516
R3517
R3527
R3550
R4401
R4402
R4403
R4404
R4405
R4406
R4407
R4408
R4409
R4410
R4411
R4412
R4413
R4414
R4415
R4416
R4417
R4418
R4420
R4421
R4422
R4423
R4424
R4425
R4426
R4427
R4428
R4429
R4430
R4432
R4433
R4434
R4435
R4437
R4438
R4439
R4440
R4441
R4442
R4443
R4444
R4447
R4448
R4449
R8451
R8452
R8453
R8455
R8458
R8459
R8462
R8463
R8475
R8476
R8480
R9602
R9603
R9605
R9606
R9610
R9612
R9613
R9614
R9617
R9620
R9621
R9623

VRS-CZ1JF220JY
VRS-CZ1JF472JY
VRS-CZ1JF220JY
VRS-CZ1JF220JY
VRS-CZ1JF220JY
VRS-CZ1JF220JY
VRS-CZ1JF220JY
VRS-CZ1JF220JY
VRK-SA1JF000JY
VRK-SA1JF000JY
VRK-SB1FF220JY
VRK-SB1FF220JY
VRK-SB1FF220JY
VRS-CZ1JF102FY
VRS-CZ1JF102FY
VRK-SB1FF220JY
VRS-CZ1JF101JY
VRS-CZ1JF101JY
VRK-SB1FF470JY
VRS-CZ1JF105JY
VRS-CZ1JF472FY
VRS-CZ1JF000JY
VRS-CZ1JF472FY
VRK-SB1FF470JY
VRK-SB1FF470JY
VRK-SB1FF470JY
VRK-SB1FF470JY
VRK-SB1FF470JY
VRK-SB1FF470JY
VRK-SB1FF470JY
VRK-SB1FF470JY
VRK-SB1FF470JY
VRS-CZ1JF103JY
VRS-CZ1JF103JY
VRS-CZ1JF103JY
VRS-CZ1JF103JY
VRS-CZ1JF103JY
VRS-CZ1JF103JY
VRS-CZ1JF101JY
VRS-CZ1JF103JY
VRS-CZ1JF333JY
VRS-CZ1JF103JY
VRK-SB1FF470JY
VRK-SB1FF470JY
VRK-SB1FF470JY
VRS-CZ1JF103JY
VRS-CZ1JF103JY
VRS-CZ1JF103JY
VRS-CZ1JF103JY
VRS-CZ1JF103JY
VRS-CZ1JF103JY
VRS-CZ1JF470JY
VRS-CZ1JF472FY
VRK-SA1JF472JY
VRK-SB1FF470JY
VRK-SB1FF470JY
VRK-SB1FF470JY
VRK-SB1FF470JY
VRS-CZ1JF472FY
VRS-CZ1JF472FY
VRS-CZ1JF472FY
VRS-CZ1JF472FY
VRS-CZ1JF470JY
VRS-CZ1JF000JY
VRS-CZ1JF472FY
VRS-CZ1JF472FY
VRK-SB1FF000JY
VRK-SB1FF000JY
VRS-CZ1JF000JY
VRS-CZ1JF000JY
VRK-SA1JF222JY
VRK-SA1JF000JY
VRK-SA1JF100JY
VRS-CY1JF000JY
VRS-CZ1JF000JY
VRS-CZ1JF101JY
VRS-CZ1JF102JY
VRS-CZ1JF472JY
VRS-CZ1JF101JY
VRS-CZ1JF101JY
VRS-CZ1JF000JY
VRS-CZ1JF101JY
VRS-CZ1JF432FY
VRS-CZ1JF103FY
VRS-CY1JF000JY

AA
AA
AA
AA
AA
AA
AA
AA
AB
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AB
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA

J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J

Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor

13

22 1/16W Metal Oxide


4.7k 1/16W Metal Oxide
22 1/16W Metal Oxide
22 1/16W Metal Oxide
22 1/16W Metal Oxide
22 1/16W Metal Oxide
22 1/16W Metal Oxide
22 1/16W Metal Oxide
0 1/16W Metal Composition
0 1/16W Metal Composition
22 1/32W Metal Composition
22 1/32W Metal Composition
22 1/32W Metal Composition
1k 1/16W Metal Oxide
1k 1/16W Metal Oxide
22 1/32W Metal Composition
100 1/16W Metal Oxide
100 1/16W Metal Oxide
47 1/32W Metal Composition
1M 1/16W Metal Oxide
4.7k 1/16W Metal Oxide
0 1/16W Metal Oxide
4.7k 1/16W Metal Oxide
47 1/32W Metal Composition
47 1/32W Metal Composition
47 1/32W Metal Composition
47 1/32W Metal Composition
47 1/32W Metal Composition
47 1/32W Metal Composition
47 1/32W Metal Composition
47 1/32W Metal Composition
47 1/32W Metal Composition
10k 1/16W Metal Oxide
10k 1/16W Metal Oxide
10k 1/16W Metal Oxide
10k 1/16W Metal Oxide
10k 1/16W Metal Oxide
10k 1/16W Metal Oxide
100 1/16W Metal Oxide
10k 1/16W Metal Oxide
33k 1/16W Metal Oxide
10k 1/16W Metal Oxide
47 1/32W Metal Composition
47 1/32W Metal Composition
47 1/32W Metal Composition
10k 1/16W Metal Oxide
10k 1/16W Metal Oxide
10k 1/16W Metal Oxide
10k 1/16W Metal Oxide
10k 1/16W Metal Oxide
10k 1/16W Metal Oxide
47 1/16W Metal Oxide
4.7k 1/16W Metal Oxide
4.7k 1/16W Metal Composition
47 1/32W Metal Composition
47 1/32W Metal Composition
47 1/32W Metal Composition
47 1/32W Metal Composition
4.7k 1/16W Metal Oxide
4.7k 1/16W Metal Oxide
4.7k 1/16W Metal Oxide
4.7k 1/16W Metal Oxide
47 1/16W Metal Oxide
0 1/16W Metal Oxide
4.7k 1/16W Metal Oxide
4.7k 1/16W Metal Oxide
0 1/32W Metal Composition
0 1/32W Metal Composition
0 1/16W Metal Oxide
0 1/16W Metal Oxide
2.2k 1/16W Metal Composition
0 1/16W Metal Composition
10 1/16W Metal Composition
0 1/16W Metal Oxide
0 1/16W Metal Oxide
100 1/16W Metal Oxide
1k 1/16W Metal Oxide
4.7k 1/16W Metal Oxide
100 1/16W Metal Oxide
100 1/16W Metal Oxide
0 1/16W Metal Oxide
100 1/16W Metal Oxide
4.3k 1/16W Metal Oxide
10k 1/16W Metal Oxide
0 1/16W Metal Oxide

LC-32/40/46LE600E/RU/S
NO.

PARTS CODE

PRICE NEW
RANK MARK

PART
DELIVERY

DESCRIPTION

[3] DUNTKF111FM11 (MAIN Unit)

R9624
R9626
R9627
R9628
R9629
R9630
R9631
R9632
R9633
R9634
R9635
R9636
R9637
R9638
R9639
R9640
R9641
R9643
R9645
R9646
R9648
R9650
R9652
R9653
R9654
R9655
R9656
R9657
R9658
R9659
R9660
R9661
R9662
R9664
R9665
R9666
R9680
R9681
RDA3301
SC501
SC502
SC503
SC504
SC1501
SC1502
SC1503
SC4401
TH3301
TU1102
VA3301
VA3302
X3301
X4401
N

VRS-CZ1JF101JY
VRS-CZ1JF101JY
VRS-CZ1JF000JY
VRS-CZ1JF473FY
VRS-CZ1JF153FY
VRS-CZ1JF153FY
VRS-CZ1JF123FY
VRS-CZ1JF102JY
VRS-CZ1JF101JY
VRS-CZ1JF3R9JY
VRS-CZ1JF103JY
VRS-CZ1JF103JY
VRS-CZ1JF101JY
VRS-CZ1JF303FY
VRS-CZ1JF562JY
VRS-CZ1JF562FY
VRS-CZ1JF101JY
VRS-CZ1JF101JY
VRS-CZ1JF102JY
VRS-CZ1JF000JY
VRS-CZ1JF103JY
VRS-CZ1JF101JY
VRS-CZ1JF101JY
VRS-TW2HF1R0JY
VRS-TW2HF1R0JY
VRS-TW2HF1R0JY
VRS-CZ1JF101JY
VRS-CZ1JF753FY
VRS-CZ1JF123FY
VRS-TW2HF1R0JY
VRS-TW2HF1R0JY
VRS-TW2HF3R3JY
VRS-TW2HF3R3JY
VRS-CZ1JF105JY
VRS-CZ1JF101JY
VRS-CZ1JF102JY
VRS-CZ1JF103JY
VRS-CZ1JF102JY
PRDARA577WJFW
QSOCNA770WJZZ
QSOCZA161WJZZ
QSOCZA161WJZZ
QSOCNA769WJZZ
QSOCZA173WJQZY
QSOCZA173WJQZY
QSOCZA072WJZZQ
Not Available
VHHM1103J03-1Y
RTUDAA019WJQZ
RH-VXA194WJZZY
RH-VXA194WJZZY
Not Available
RCRSCA039WJZZY
PSPAZB312WJKZ

AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AF
AG
AG
AG
AG
AG
AG
AH
AC
AZ
AC
AC
AG
AD

J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J

Resistor 100 1/16W Metal Oxide


Resistor 100 1/16W Metal Oxide
Resistor 0 1/16W Metal Oxide
Resistor 47k 1/16W Metal Oxide
Resistor 15k 1/16W Metal Oxide
Resistor 15k 1/16W Metal Oxide
Resistor 12k 1/16W Metal Oxide
Resistor 1k 1/16W Metal Oxide
Resistor 100 1/16W Metal Oxide
Resistor 3.9 1/16W Metal Oxide
Resistor 10k 1/16W Metal Oxide
Resistor 10k 1/16W Metal Oxide
Resistor 100 1/16W Metal Oxide
Resistor 30k 1/16W Metal Oxide
Resistor 5.6k 1/16W Metal Oxide
Resistor 5.6k 1/16W Metal Oxide
Resistor 100 1/16W Metal Oxide
Resistor 100 1/16W Metal Oxide
Resistor 1k 1/16W Metal Oxide
Resistor 0 1/16W Metal Oxide
Resistor 10k 1/16W Metal Oxide
Resistor 100 1/16W Metal Oxide
Resistor 100 1/16W Metal Oxide
Resistor 1 1/2W Metal Oxide
Resistor 1 1/2W Metal Oxide
Resistor 1 1/2W Metal Oxide
Resistor 100 1/16W Metal Oxide
Resistor 75k 1/16W Metal Oxide
Resistor 12k 1/16W Metal Oxide
Resistor 1 1/2W Metal Oxide
Resistor 1 1/2W Metal Oxide
Resistor 3.3 1/2W Metal Oxide
Resistor 3.3 1/2W Metal Oxide
Resistor 1M 1/16W Metal Oxide
Resistor 100 1/16W Metal Oxide
Resistor 1k 1/16W Metal Oxide
Resistor 10k 1/16W Metal Oxide
Resistor 1k 1/16W Metal Oxide
Heat Sink
Socket
Socket
Socket
Socket
Socket
Socket
Socket
Connector *PWB replacement item
Thermistor
Tuner
Varistor AVRL161A1R1NTB
Varistor AVRL161A1R1NTB
Crystal *PWB replacement item
Crystal
Spacer

[4] CABINET AND MECHANICAL PARTS (LC-32LE600E/RU/S)


1
2
2-2
5
5-1
8
17
18
21
24
22
26
33
33
35
N
N

CCABAC371WJ12
CCABBB619WJ12
Not Available
CANGKC375WJ02
Not Available
LHLDWA289WJKZ
QCNW-J895WJQZ
QCNW-J896WJQZ
QCNW-G182WJQZ
QCNW-J712WJQZ
QCNW-K027WJQZ
QCNW-J996WJQZ
TLABZC352WJZZ
TLABZC353WJZZ
XBPS730P06000
GCOVAD472WJ1A
QCNW-J892WJQZ

BG
BG
AL
AC
AF
AF
AF
AW
AK
AP
AA
AH
AH

N
N
N
N
N
N
N
N
N
N
N
N
S
N

P
P
P
J
P
P
J
P
P
P
P
P
J
P
P

Front Cabinet Ass'y


Rear Cabinet Ass'y
Terminal Label
Side Terminal Angle Ass'y
Side Terminal Label
Wire Holder, x2
Connecting Cord Main-Power(PD)
Connecting Cord Main-Power(LB)
Connecting Cord Main-Power(PL)
Connecting Cord Main-LCD Control(LP)
Connecting Cord Main-LCD Control(LW)
Connecting Cord(AS)
POP Label (except for Russia)
POP Label (for Russia)
Screw for HDMI, x3
Bottom Cover
Connecting Cord Main-R/C, LED-Key(RA/KM)

[5] LCD PANEL MODULE UNIT (LC-32LE600E/RU/S)


1
1-4
1-5
1-22
1-28
N

DLCUCA001FM02
RUNTK4248TPZB
XHPS730P06WS0
R1LK315D3FZF0Y
LX-HZA039WJF7
LX-HZA064WJF7

BL
AA
CP
AB
AB

N
N
N
N

P
P
J
P
J
P

32"LCD Panel Module Unit (LC-32LE600E/RU/S)


LCD Control Unit
Screw, x4
32" LCD Panel
Screw, x8
Wsher Screw, x2

14

LC-32/40/46LE600E/RU/S
NO.

PARTS CODE

PRICE NEW
RANK MARK

PART
DELIVERY

DESCRIPTION

[6] CABINET AND MECHANICAL PARTS (LC-40LE600E/RU/S)


1
1-2
2
2-2
5
5-1
17
18
21
22
24
26
33
33
35
N
N
N
N

CCABAC372WJ12
Not Available
CCABBB618WJ12
Not Available
CANGKC375WJ02
Not Available
QCNW-J903WJQZ
QCNW-J904WJQZ
QCNW-J906WJQZ
QCNW-K029WJQZ
QCNW-J801WJQZ
QCNW-J996WJQZ
TLABZC322WJZZ
TLABZC323WJZZ
XBPS730P06000
GCOVAD464WJ1A
LHLDQA001WJ1A
PSLDMB651WJZZ
QCNW-J900WJQZ

BK
BH
AL
AK
AG

N
N
N
N
S
N
N
N

AX
AG

N
N
N
N
N

AH
AP
AA
AL
AF
AC
AH

S
S
S
N

P
P
P
J
P
P
P
P
P
P
P
J
P
P
P
P

Front Cabinet Ass'y


Front Decoration Ass'y
Rear Cabinet Ass'y
Terminal Label
Side Terminal Angle Ass'y
Side Terminal Label
Connecting Cord Main-Power(PD)
Connecting Cord Main-Power(LB)
Connecting Cord Main-Power(PL)
Connecting Cord Main-LCD Control(LW)
Connecting Cord Main-LCD Control(LP)
Connecting Cord(AS)
POP Label (except for Russia)
POP Label (for Russia)
Screw for HDMI, x3
Bottom Cover
Wire Holder
Conductor: 10x60
Connecting Cord Main-R/C, LED-Key(RA/KM)

[7] LCD PANEL MODULE UNIT (LC-40LE600E/RU/S)


1
1-3
1-4
1-24
1-31
N

DLCUCA002FM02
RUNTK4248TPZA
XBPS730P06WS0
R1LK400D3FZC0Y
LX-BZA213WJF7
LX-BZA348WJF7

BL
AA
CR
AA
AB

N
N
N
N

P
P
J
P
J
P

40"LCD Panel Module Unit (LC-40LE600E/RU/S)


LCD Control Unit
Screw, x4
40" LCD Panel
Screw, x10
Wsher Screw, x4

[8] CABINET AND MECHANICAL PARTS (LC-46LE600E/RU/S)


1
1-2
2
2-2
5
5-1
17
20
21
22
24
26
28
34
34
36
N
N
N
N

CCABAC378WJ12
Not Available
CCABBB617WJ12
Not Available
CANGKC375WJ02
Not Available
PSLDMB651WJZZ
QCNW-H973WJQZ
QCNW-J911WJQZ
QCNW-J912WJQZ
QCNW-K031WJQZ
QCNW-J801WJQZ
QCNW-K104WJQZ
TLABZC322WJZZ
TLABZC323WJZZ
XBPS730P06000
GCOVAD479WJ1A
QCNW-J908WJQZ
LHLDQA001WJ1A
RCORFA038WJZZ

BL
BM
AL
AC
AG
AG
AX
AG
AU
AH
AP
AM
AM
AH
AF
AH

N
N
N
N
S
N
N
N
N
N
N
N
N
S

P
P
P
P
P
P
P
P
P
P
P
P
J
P
P
P
J

Front Cabinet Ass'y


Front Decoration Ass'y
Rear Cabinet Ass'y
Terminal Label
Side Terminal Angle Ass'y
Side Terminal Label
Conductor: 10x60, x2
Connecting Cord Main-Power(PL)
Connecting Cord Main-Power(PD)
Connecting Cord Main-Power(LB)
Connecting Cord Main-LCD Control(LW)
Connecting Cord Main-LCD Control(LP)
Connecting Cord Power(AS)
POP Label (except for Russia)
POP Label (for Russia)
Screw for HDMI, x3
Bottom Cover
Connecting Cord Main-R/C, LED-Key(RA/KM)
Wire Holder
Ferrite Core

[9] LCD PANEL MODULE UNIT (LC-46LE600E/RU/S)


1
1-3
1-4
1-5
1-26
N

DLCUCA003FM02
RUNTK4248TPZZ
XHPS730P06WS0
QCNW-K183WJQZ
R1LK460D3FZN0Y
LX-HZA064WJF7

BL
AA
AN
CT
AB

N
N
N
N
N

P
P
J
P
P
P

46"LCD Panel Module Unit (LC-46LE600E/RU/S)


LCD Control Unit
Screw, x4
Connecting Cord, x2
46" LCD Panel
Wsher Screw, x4

N
N
N
N
N
N
N

P
P
P
P
P
P
P

Stand Unit (LC-32LE600E/RU/S)


Stand Unit (LC-40LE600E/RU/S)
Stand Unit (LC-46LE600E/RU/S)
Operation Manual (for Europe except East Europe)
Operation Manual (for Sweden)
Operation Manual (for East Europe)
Operation Manual (for Russia)

J
J
J
J
J
J
J

Main+LCD Control-Power(LB)
Main-R/C, LED-Key(RA/KM)
Connecting Cord Main-LCD Control(LW)
Connecting Cord Main-LCD Control(LP)
Connecting Cord Main-Power(PL)
Connecting Cord Main-Power(PD)
Connecting Cord Main-Speaker(SP)

[10] SUPPLIED ACCESSORIES


X4
X4
X4
X5
X5
X5
X5

CDAI-A584WJ02
CDAI-A586WJ02
CDAI-A588WJ02
TINS-E285WJZZ
TINS-E286WJZZ
TINS-E287WJZZ
TINS-E288WJZZ

BG
BH
BL
AG
AF
AL
AD

[11] SERVICE JIGS (USE FOR SERVICING)


N
N
N
N
N
N
N

QCNW-K037WJQZ
QCNW-K039WJQZ
QCNW-G616WJQZ
QCNW-H347WJQZ
QCNW-G625WJQZ
QCNW-H184WJQZ
QCNW-J413WJPZ

BK
AY
AP
AX
AQ

15

LC-32/40/46LE600E/RU/S
LC32LE600E

Service Manual
OUTLINE AND DIFFERENCES FROM BASE MODEL
OUTLINE
This model is based on the LC-32LE700E/RU/S, LC-40LE700E/RU/S, LC-46LE700E/RU/S and is changed some parts. This Service Manual covers
the modifications alone. For the other points, refer to the LC-32LE700E/RU/S, LC-40LE700E/RU/S and LC-46LE700E/RU/S (No. S89B4LC32L700)
Service Manual.

LC-32/40/46LE600E/RU/S
DIFFERENCES FROM BASE MODEL
LIST OF CHANGED PARTS (LC-32LE600E/RU/S)
Ref.
Description
No.
PRINTED WIRING BOARD ASSEMBLIES
KEY Unit
MAIN Unit
R/C, LED Unit
ICON Unit
POWER Unit
LCD Control Unit
LED5 PWB1 Unit
LED5 PWB2 Unit
LED8 PWB1 Unit
LED8 PWB2 Unit
LCD PANEL
32" LCD Panel Module Unit
CABINET AND MECHANICAL PARTS
1
Front Cabinet Assy
1-4
Diffusion Sheet
2
Rear Cabinet Assy
2-2
Terminal Label
4
Bottom Cover Assy
5
Side Terminal Angle Assy
5-1
Side Terminal Label
8
Wire Holder
18
Connecting Cord Main-Power(LB)
19
Connecting Cord Main-Key(KM)
20
Connecting Cord Main-R/C, LED(RA)
21
Connecting Cord Main-Power(PL)
22
Connecting Cord Main-LCD Control(LW)
24
Connecting Cord Main-LCD Control(LP)
25
Connecting Cord R/C, LED-ICON(IM)
33
POP Label (except for Russia)
33
POP Label (for Russia)
35
Screw (for HDMI)
N
Bottom Cover
N
Connecting Cord Main-R/C, LED-Key(RA/KM)
LCD PANEL MODULE UNIT
1
32" LCD Panel Module Unit
1-4
LCD Control Unit
1-5
Screw
1-22 32 LCD Panel
1-28 Screw
N
Washer Screw
SUPPLIED ACCESSORIES
X4
Stand Unit
X5
Operation Manual (for Europe except E-Europe)
X5
Operation Manual (for Sweden)
X5
Operation Manual (for East Europe)
X5
Operation Manual (for Russia)
SERVICE JIGS (USE FOR SERVICING)
Main+LCD Control-Power(LB)
Main-Key(KM)
Main-R/C, LED(RA)
Main-R/C, LED-Key(RA/KM)
R/C, LED-ICON(IM)
MAIN Unit: Please refer to a Parts list.

LC-32LE700E/RU/S
(No. S89B4LC32L700)

LC-32LE600E/RU/S
(No. S89B5LC32L600)

Interchangeability

Note

DUNTKE266FM18
DUNTKE306FM01
DUNTKE308FM02
DUNTKF314FM02
RUNTKA619WJQZ
RUNTK4225TPZE
RUNTKA595WJ01
RUNTKA595WJ02
RUNTKA598WJ01
RUNTKA598WJ02

DUNTKF111FM11

RUNTK4248TPZB

Changed

Abolish

Changed

DLCUCA001FM03

DLCUCA001FM02

Some parts changed

CCABAC371WJ11
PSHEPB007WJKZ
CCABBB619WJ11
HINDPD390WJSA
CCOVAD472WJ11
CANGKC375WJ01
HINDPD408WJSA
LHLDWA289WJKZ, x3
QCNW-J915WJQZ
QCNW-J977WJQZ
QCNW-J976WJQZ
QCNW-J898WJQZ
QCNW-J894WJQZ
QCNW-J897WJQZ
QCNW-J916WJQZ
TLABZC319WJZZ
TLABZC320WJZZ
XBPS730P06000, x4

CCABAC371WJ12

CCABBB619WJ12
HINDPD391WJSA

CANGKC375WJ02
HINDPD470WJSA
LHLDWA289WJKZ, x2
QCNW-J896WJQZ

QCNW-G182WJQZ
QCNW-K027WJQZ
QCNW-J712WJQZ

TLABZC352WJZZ
TLABZC353WJZZ
XBPS730P06000, x3
GCOVAD472WJ1A
QCNW-J892WJQZ

D
D

D
D

D
D
D

D
D

Changed
Abolish
Changed
Changed
Abolish
Changed
Changed
Abolish (32)
Changed
Abolish
Abolish
Changed
Changed
Changed
Abolish
Changed
Changed
Abolish (43)
Addition
Addition

DLCUCA001FM03
RUNTK4225TPZE
XHPS730P06WS0, x6
R1LK315D3FZE0Y
LX-HZA039WJF7, x10

DLCUCA001FM02
RUNTK4248TPZB
XHPS730P06WS0, x4
R1LK315D3FZF0Y
LX-HZA039WJF7, x8
LX-HZA064WJF7

D
D

Some parts changed


Changed
Abolish (64)
Changed
Abolish (108)
Addition

CDAi-A595WJ02
TiNS-E281WJZZ
TiNS-E282WJZZ
TiNS-E283WJZZ
TiNS-E284WJZZ

CDAi-A584WJ02
TiNS-E285WJZZ
TiNS-E286WJZZ
TiNS-E287WJZZ
TiNS-E288WJZZ

D
D
D
D
D

Changed
Changed
Changed
Changed
Changed

QCNW-K036WJQZ
QCNW-G440WJQZ
QCNW-H184WJQZ

QCNW-G442WJPZ

QCNW-K037WJQZ

QCNW-K039WJQZ

Changed
Abolish
Abolish
Addition
Abolish

ii

LC-32/40/46LE600E/RU/S
LIST OF CHANGED PARTS (LC-40LE600E/RU/S)
Ref.
LC-40LE700E/RU/S
Description
No.
(No. S89B4LC32L700)
PRINTED WIRING BOARD ASSEMBLIES
KEY Unit
DUNTKE266FM18
MAIN Unit
DUNTKE306FM01
R/C, LED Unit
DUNTKE308FM02
ICON Unit
DUNTKF314FM02
POWER Unit
RUNTKA609WJQZ
LCD Control Unit
RUNTK4225TPZE
LED5 PWB1 Unit
RUNTKA595WJ01
LED5 PWB2 Unit
RUNTKA595WJ02
LED6 PWB1 Unit
RUNTKA596WJ01
LED6 PWB2 Unit
RUNTKA596WJ02
LCD PANEL
40" LCD Panel Module Unit
DLCUCA002FM03
CABINET AND MECHANICAL PARTS
1
Front Cabinet Assy
CCABAC372WJ11
1-2
Front Decoration Assy
CDECQB299WJ11
1-4
Diffusion Sheet
PSHEPB007WJKZ
2
Rear Cabinet Assy
CCABBB618WJ11
2-2
Terminal Label
HiNDPD390WJSA
4
Bottom Cover Assy
CCOVAD464WJ11
5
Side Terminal Angle Assy
CANGKC375WJ01
5-1
Side Terminal Label
HiNDPD408WJSA
18
Connecting Cord Main-Power(LB)
QCNW-J917WJQZ
19
Connecting Cord Main-Key(KM)
QCNW-J979WJQZ
20
Connecting Cord Main-R/C, LED(RA)
QCNW-J978WJQZ
21
Connecting Cord Main-Power(PL)
QCNW-G178WJQZ
22
Connecting Cord Main-LCD Control(LW)
QCNW-J902WJQZ
24
Connecting Cord Main-LCD Control(LP)
QCNW-J905WJQZ
25
Connecting Cord R/C, LED-ICON(IM)
QCNW-J918WJQZ
33
POP Label (except for Russia)
TLABZC319WJZZ
33
POP Label (for Russia)
TLABZC320WJZZ
35
Screw (for HDMI)
XBPS730P06000, x4
N
Bottom Cover

N
Connecting Cord Main-R/C, LED-Key(RA/KM)

N
Wire Holder

N
Conductor-10x60

LCD PANEL MODULE UNIT


1
40" LCD Panel Module Unit
DLCUCA002FM03
1-3
LCD Control Unit
RUNTK4225TPZE
1-4
Screw
XHPS730P06WS0, x6
1-24 40 LCD Panel
R1LK400D3FZB0Y
1-31 Screw
LX-BZA213WJF7, x14
N
Washer Screw

SUPPLIED ACCESSORIES
X4
Stand Unit
CDAi-A600WJ02
X5
Operation Manual (for Europe except E-Europe) TiNS-E281WJZZ
X5
Operation Manual (for Sweden)
TiNS-E282WJZZ
X5
Operation Manual (for East Europe)
TiNS-E283WJZZ
X5
Operation Manual (for Russia)
TiNS-E284WJZZ
SERVICE JIGS (USE FOR SERVICING)
Main+LCD Control-Power(LB)
QCNW-K036WJQZ
Main-Key(KM)
QCNW-G440WJQZ
Main-R/C, LED(RA)
QCNW-H184WJQZ
Main-R/C, LED-Key(RA/KM)

R/C, LED-ICON(IM)
QCNW-G442WJPZ
MAIN Unit: Please refer to a Parts list.

iii

LC-40LE600E/RU/S
(No. S89B5LC32L600)

Interchangeability

Note

DUNTKF111FM11

RUNTK4248TPZA

Changed

Abolish

Changed

DLCUCA002FM02

Some parts changed

CCABAC372WJ12
CDECQB299WJ12

CCABBB618WJ12
HiNDPD391WJSA

CANGKC375WJ02
HiNDPD470WJSA
QCNW-J904WJQZ

QCNW-J906WJQZ
QCNW-K029WJQZ
QCNW-J801WJQZ

TLABZC322WJZZ
TLABZC323WJZZ
XBPS730P06000, x3
GCOVAD464WJ1A
QCNW-J900WJQZ
LHLDW1033CE00
PSLDMB651WJZZ

D
D

D
D

D
D
D

D
D
D

D
D

Changed
Changed
Abolish
Changed
Changed
Abolish
Changed
Changed
Changed
Abolish
Abolish
Changed
Changed
Changed
Abolish
Changed
Changed
Abolish (43)
Addition
Addition
Addition
Addition

DLCUCA002FM02
RUNTK4248TPZA
XHPS730P06WS0, x4
R1LK400D3FZC0Y
LX-BZA213WJF7, x10
LX-BZA348WJF7

D
D

Some parts changed


Changed
Abolish (64)
Changed
Abolish (1410)
Addition

CDAi-A586WJ02
TiNS-E285WJZZ
TiNS-E286WJZZ
TiNS-E287WJZZ
TiNS-E288WJZZ

D
D
D
D
D

Changed
Changed
Changed
Changed
Changed

QCNW-K037WJQZ

QCNW-K039WJQZ

Changed
Abolish
Abolish
Addition
Abolish

LC-32/40/46LE600E/RU/S
LIST OF CHANGED PARTS (LC-46LE600E/RU/S)
Ref.
Description
No.
PRINTED WIRING BOARD ASSEMBLIES
KEY Unit
MAIN Unit
R/C, LED Unit
ICON Unit
POWER Unit
LCD Control Unit
LED5 PWB1 Unit
LED5 PWB2 Unit
LED6 PWB1 Unit
LED6 PWB2 Unit
LED8 PWB1 Unit
LED8 PWB2 Unit
LCD PANEL
46" LCD Panel Module Unit
CABINET AND MECHANICAL PARTS
1
Front Cabinet Assy
1-2
Front Decoration Assy
1-4
Diffusion Sheet
2
Rear Cabinet Assy
2-2
Terminal Label
4
Bottom Cover Assy
5
Side Terminal Angle Assy
5-1
Side Terminal Label
17
Conductor-10x60
19
Connecting Cord Main-Key(KM)
20
Connecting Cord Main-Power(PL)
22
Connecting Cord Main-Power(LB)
23
Connecting Cord Main-R/C, LED(RA)
24
Connecting Cord Main-LCD Control(LW)
26
Connecting Cord Main-LCD Control(LP)
27
Connecting Cord R/C, LED-ICON(IM)
28
Connecting Cord Power(AS)
34
POP Label (except for Russia)
34
POP Label (for Russia)
36
Screw (for HDMI)
N
Bottom Cover
N
Connecting Cord Main-R/C, LED-Key(RA/KM)
N
Wire Holder
N
Ferrite Core
LCD PANEL MODULE UNIT
1
46" LCD Panel Module Unit
1-3
LCD Control Unit
1-4
Screw
1-5
Connecting Cord
1-6
Ferrite Core
1-26 46 LCD Panel
N
Washer Screw
SUPPLIED ACCESSORIES
X4
Stand Unit
X5
Operation Manual (for Europe except E-Europe)
X5
Operation Manual (for Sweden)
X5
Operation Manual (for East Europe)
X5
Operation Manual (for Russia)
SERVICE JIGS (USE FOR SERVICING)
Main+LCD Control-Power(LB)
Main-Key(KM)
Main-R/C, LED(RA)
Main-R/C, LED-Key(RA/KM)
R/C-ICON(IM)
MAIN Unit: Please refer to a Parts list.

LC-46LE700E/RU/S
(No. S89B4LC32L700)

LC-46LE600E/RU/S
(No. S89B5LC32L600)

Interchangeability

Note

DUNTKE266FM18
DUNTKE306FM01
DUNTKE308FM02
DUNTKF314FM02
RUNTKA611WJQZ
RUNTK4225TPZE
RUNTKA595WJ01
RUNTKA595WJ02
RUNTKA596WJ01
RUNTKA596WJ02
RUNTKA598WJ01
RUNTKA598WJ02

DUNTKF111FM11

RUNTK4248TPZZ

Changed

Abolish

Changed

DLCUCA003FM03

DLCUCA003FM02

Some parts changed

CCABAC378WJ11
CDECQB309WJ11
PSHEPB007WJKZ
CCABBB617WJ11
HiNDPD390WJSA
CCOVAD479WJ11
CANGKC375WJ01
HiNDPD408WJSA
PSLDMB651WJZZ, x1
QCNW-J981WJQZ
QCNW-J914WJQZ
QCNW-J919WJQZ
QCNW-J980WJQZ
QCNW-J910WJQZ
QCNW-J913WJQZ
QCNW-J920WJQZ
QCNW-J966WJQZ
TLABZC319WJZZ
TLABZC320WJZZ
XBPS730P06000, x4

CCABAC378WJ12
CDECQB309WJ12

CCABBB617WJ12
HiNDPD391WJSA

CANGKC375WJ02
HiNDPD470WJSA
PSLDMB651WJZZ, x2

QCNW-H973WJQZ
QCNW-J912WJQZ

QCNW-K031WJQZ
QCNW-J801WJQZ

QCNW-K104WJQZ
TLABZC322WJZZ
TLABZC323WJZZ
XBPS730P06000, x3
GCOVAD479WJ1A
QCNW-J908WJQZ
LHLDW1033CE00
RCORFA038WJZZ

D
D

D
D

D
D

D
D

D
D

D
D
D

Changed
Changed
Abolish
Changed
Changed
Abolish
Changed
Changed
Addition (12)
Abolish
Changed
Changed
Abolish
Changed
Changed
Abolish
Changed
Changed
Changed
Abolish (43)
Addition
Addition
Addition
Addition

DLCUCA003FM03
RUNTK4225TPZE
XHPS730P06WS0, x6
QCNW-H089WJQZ
RCORFA061WJZZ
R1LK460D3FZL0Y

DLCUCA003FM02
RUNTK4248TPZZ
XHPS730P06WS0, x4
QCNW-K183WJQZ

R1LK460D3FZN0Y
LX-HZA064WJF7

D
D

Some parts changed


Changed
Abolish (64)
Changed
Abolish
Changed
Addition

CDAi-A593WJ02
TiNS-E281WJZZ
TiNS-E282WJZZ
TiNS-E283WJZZ
TiNS-E284WJZZ

CDAi-A588WJ02
TiNS-E285WJZZ
TiNS-E286WJZZ
TiNS-E287WJZZ
TiNS-E288WJZZ

D
D
D
D
D

Changed
Changed
Changed
Changed
Changed

QCNW-K036WJQZ
QCNW-G440WJQZ
QCNW-H184WJQZ

QCNW-G442WJPZ

QCNW-K037WJQZ

QCNW-K039WJQZ

Changed
Abolish
Abolish
Addition
Abolish

iv

LC-32/40/46LE600E/RU/S
Interchangeability
A:

Completely interchangeable

OLD = NEW

C:

Interchangeable from
NEW to OLD

NEW

B:

Interchangeable from
OLD to NEW

OLD

D:

Not interchangeable

NEW X OLD

NEW

OLD

LC-32/40/46LE600E/RU/S

CHAPTER 4. ADJUSTMENT PROCEDUREService


LC32LE600E

Manual

[1] ADJUSTMENT PROCEDURE


1. Adjustment method after PWB and/or IC replacement due to repair
The unit is set to the optimum at the time of shipment from the factory. If any value should become improper or any adjustment is necessary due to
the part replacement, make an adjustment according to the following procedure.
1. Procure the following units in order to replace the main unit, E2PROM (IC8455).
MAIN UNIT:

DUNTKF111FM11

NOTE: [Caution when replacing ICs in the main unit (IC501)]


The above ICs are EEPROMs storing the EDID data of PC data.
Before replacing the relevant part, procure the following parts in which the data have been rewritten.
IC501

RH-iXC206WJQZS

EDID (PC)

ANALOG-RGB

2. Entering and exiting the adjustment process mode


1. Press the MAIN POWER key on the set of running TV set to force power off.
(Or, unplug the AC power cord of running TV set to force power off.)
2. While holding down the

(-) and INPUT keys on the set at once, press the MAIN POWER key on the set to turn on the power.

The letter K appears on the screen.


3. Next, hold down the

(-) and P (

) keys on the set at once.

Multiple lines of orange characters appearing on the screen indicate that the set is now in the adjustment process mode.
If you fail to enter the adjustment process mode (the display is the same as normal start up), retry the procedure.
4. To exit the adjustment process mode after the adjustment is done, press the MAIN POWER key and turn off a power supply. or unplug the AC
power cord to force power off.
(When the power is turned off with the remote controller, once unplug the AC power cord and wait for 10 seconds before plug it in again.)
CAUTION: Use due care in handling the information described here lest the users should know how to enter the adjustment process mode.
If the settings are tampered with in this mode, unrecoverable system damage may result.

3. Remote controller key operation in adjustment process mode.


1. key operation
Remote controller key
P(
/
)
(+/-)
Cursor ( / )
Cursor ( / )
Input button
OK

Main unit key


P(
/
)
(+/-)

Input button

Remote controller key Main unit key Function


Moving an item (line) by one (UP/DOWN)
Changing a selected item setting (+1/-1)
Turning a page (PREVIOUS/NEXT)
Changing a selected line setting (+10/-10)
Input source switching (toggle switching)
(TVEXT1EXT2EXT3EXT4HDMI1HDMI2HDMI3EXT8)
Executing a function

Input mode is switched automatically when relevant adjustment is started so far as the necessary input signal is available.

41

LC-32/40/46LE600E/RU/S
4. Description of display
(1) Current page / Total pages

(2) Currentry selected input


(3) Inch setting and Model name display

PAGE 1/8
Main Version
Boot Version
T-CON Version
CPLD Version
INCH SIZE
ERROR RESET
STANDBY CAUSE

(4) Item name

No.
(1)
(2)
(3)
(4)
(5)

Description
Current page/total pages
Currently selected input
Inch setting and destination display
Item name
Parameter table

TV

**E_LE600E

Adjustment process menu header

1.14
20090429.1.12
00 00 00 00 32 4C 32 B1
xx
xx
NO [NO/YES]
00 00 00 00 00
[1]
00H 00M
[2]
00H 00M
[3]
00H 00M
[4]
00H 00M
[5]
00H 00M

(5) Parameter

Display specification
2char/2char Decimal Number mark.
TVEXT1EXT2EXT3EXT4HDMI1HDMI2HDMI3EXT8
32/40/46
Max. 30 char
Max. 60 char (Preset value of each item)

42

LC-32/40/46LE600E/RU/S
5. Adjustment process mode menu
The character string in brackets [ ] will appear as a page title in the adjustment process menu header.
Page
1/8

Line

Item

Description

Remarks (adjustment detail, etc.)

1
2
3
4
5
6
7

Main Version
Boot Version
T-CON Version
CPLD Version
INCH SIZE
ERROR RESET
STANDBY CAUSE

1.14
20090429.1.12
00 00 00 00 32 4C 32 B1
xx
32/40/46
NO [NO/YES]
00 00 00 00 00
1) 00H 00M
2) 00H 00M
3) 00H 00M
4) 00H 00M
5) 00H 00M

Main microprocessor version


Boot version of the main microprocessor
T-CON microprocessor version
CPLD Version for Backlight controller
Initial Setting of panel size
Lamp error reset. (Select YES and press OK key.)
Error standby cause. Total operating time before error.
(5 times histories)

1
2
3
4

INDUSTRY INIT
PUBLIC MODE
I2C DATA
I2C STATE

[NO/YES(E)/YES(I)/YES(F)/YES(R)
OFF [OFF/ON]
000000000000
WAIT [STANDBY/WAIT]

Initialization to factory settings execution.


ON/OFF setting of hotel mode
Write and read of data in I2C BUS control IC.
Execution of write and read of I2C DATA

1
2

INSPECT USB TERM


HDMI CEC TEST

ENTER
ENTER

Reading inspection of USB memory terminal


HDMI CEC test

1
2
3
4

TUNER ADJ
CHANNEL
GAIN
ADJ RESET

ENTER
E-12/E-9(SMPTE)/E-12(SMPTE)
31
NO [NO/YES]

VIDEO level adjustment execution

1
2

VIDEO ADJ
GAIN

ENTER
31

VIDEO level adjustment execution

1
2
3
4
5
6
7
8

COM-ADJ
Y OFF SET
PB OFF SET
PR OFF SET
Y GAIN
PB GAIN
PR GAIN
ADJ RESET

ENTER
70
128
128
140
140
140
NO [NO/YES]

COMPONENT level adjustment execution


Y CUTOFF adjustment value
PB CUTOFF adjustment value
PR CUTOFF adjustment value
Y GAIN adjustment value
PB GAIN adjustment value
PR GAIN adjustment value
Reset of adjustment

1
2
3
4
5
6
7
8

RGB-ADJ
R OFF SET
G OFF SET
B OFF SET
R GAIN
G GAIN
B GAIN
ADJ RESET

ENTER
128
128
128
80
80
80
NO [NO/YES]

SCART RGB level adjustment execution


R OFF SET adjustment value
G OFF SET adjustment value
B OFF SET adjustment value
R DRIVE adjustment value
G DRIVE adjustment value
B DRIVE adjustment value
Reset of adjustment

1
2
3
4
5
6
7
8
9
10
11
12

COM BIAS
LCD TEST PATTERN
WB Point A
Point B
Point A ADJ R
ADJ G
ADJ B
Point B ADJ R
ADJ G
ADJ B
WB WRITE
WB RESET

67
0
1280
3712
1280
1280
1280
3712
3712
3712
NO [NO/YES]
NO [NO/YES]

Common Bias auto adjustment execution


Pattern with built-in LCD controller display
W/B adjustment, gradation Point A input setting
W/B adjustment, gradation Point B input setting
W/B adjustment, gradation Point A R_adjustment value
W/B adjustment, gradation Point A G_adjustment value
W/B adjustment, gradation Point A B_adjustment value
W/B adjustment, gradation Point B R_adjustment value
W/B adjustment, gradation Point B G_adjustment value
W/B adjustment, gradation Point B B_adjustment value
W/B writing of adjustment values
Reset of W/B adjustment value

2/8

3/8

4/8

Gain adjustment
Reset of adjustment

5/8

6/8

7/8

8/8

43

LC-32/40/46LE600E/RU/S
6. Special features
1. STANDBY CAUSE (Page 1/8)
Display of a cause (code) of the last standby.
The cause of the last standby is recorded in EEPROM whenever possible.
Checking this code will be useful in finding a problem when you repair the troubled set.

7. ROM Writing (HDMI_EDID)


1. EDID writing
1) Get ready the PC with COM port (RS-232C) running on Windows 95/98/ME/2000/XP operating system, as well as the RS-232C cross cable.
2) Start the set with the set connected with the personal computer with the RS232C cross cable.
3) Start the terminal software. (The free ware readily available on the Internet will do.)
4) Make the following settings.
Baud rate
Data LENGTH
Parity bit
Stop bit
Flow control

: 9600 bps
: 8bit
: none
: 1 bit
: none

5) Input following commands to terminal software.


KRSW0001
PC replies ERR (you should ignore this replay)
KKT10037
PC replies OK
WRED0000
PC replies OK... At that time, EDID writing finish with success.
6) It usually returns to a state by AC-OFF/ON.
Disconnect and connect AC cable, then TV wakes up with normal mode.
2. Software version
(1) Mainmicon Software
(2) Boot version of mainmicon Software
(3) T-CON Monitor micon Software
(4) CPLD Version

Ver. 1.14 *1
Ver. 1.12 *1
Ver. 1.0 *1
XX *1

*1 Please refer to the change report document for the latest version (Issued it to SEES).

44

LC-32/40/46LE600E/RU/S
8. Adjustment procedure
1. Inch Setting
1

Adjustment point
Inch Setting

Adjustment conditions
Adjustment process mode

Adjustment process
INCH SIZE menu page 1/8

Adjustment procedure
1) Inch Setting with adjustment process mode.
2) Enter the adjustment process mode, refering to the 2nd item.
3) By using P (
/
) key of R/C, Move the cursor to INCH SIZE on page 1/
8.
4) Select inch size 32/40/46 with the Volume (+)/(-) key of remote control.
5) Press the OK key of remote control.
6) After a while, If *** OK *** is displayed, the setting is completed.

2. COMB-BIAS Adjustment
1

Adjustment point
COM-BIAS Adjustment

Adjustment conditions
A visual check

Adjustment process
COM BIAS menu page 8/8

Adjustment procedure
1) COM-BIAS Adjustment with adjustment process mode.
2) Enter to the adjustment process mode, refering to the 2nd item.
3) By using
/
key and P (
/
) key of R/C, Move the cursor to COMBIAS on page 8/8.
4) Press the OK key. then, you can check that the pattern for adjustment is
displayed.
5) Adjust so that the flicker for the central part of a screen becomes the minimum using the volume (+)/(-) key of R/C.
6) In order to exit from this process, press the OK key of remote control again.

45

LC-32/40/46LE600E/RU/S
9. Video signal adjustment procedure
*

The adjustment process mode menu is listed in 5th item.

Signal generator level adjustment check (Adjustment to the specified level)

Composite signal PAL/SECAM


PC (Analog D_sub15pin) signal
33K component signal

: 0.7Vp-p 0.02Vp-p (White level from pedestal)


: 0.7Vp-p 0.02Vp-p (White level from pedestal)
: Y level 0.7Vp-p 0.02Vp-p (White level from pedestal)
: PB,PR level 0.7Vp-p 0.02Vp-p

1. Picture Adjustment
1) Entering the adjustment process mode
Adjustment point

Adjustment conditions

Adjustment procedure
Enter to the adjustment process mode, refering to the 2nd item.

2) TUNER adjustment
1

Adjustment point
Setting

Adjustment conditions
[Signal]
PAL split colour Bar
In-house UV

Adjustment procedure
Feed the In-house signal (PAL color bar) to TUNER.
Make sure the PAL colour bar pattern has the sync level of 7:3 with the picture level.
Feed the SMPTE color bar signal to TUNER.
JABIL: 203.25MHz

[Terminal]
TUNER

Auto adjustment
performance

[SMPTE pattern]

Adjustment process
[VIDEO ADJ] menu page 4/8

Bring the cursor on [VIDEO ADJ] and press OK key [*** OK ***] appears when
finished.

Adjustment conditions
[Signal]
PAL full colour Bar

3) PAL signal adjustment


1

Adjustment point
Setting

Adjustment procedure
Feed the PAL full field colour bar (color saturation level 100%) signal to the
SCART video input of EXT1.

[VIDEO input signal]


[Terminal]
EXT1 SCART Video input

100% white

Auto adjustment
performance

Adjustment process
[VIDEO ADJ] menu page 5/8

Black

Bring the cursor on [VIDEO ADJ] and press OK key [*** OK ***] appears when
finished.

46

LC-32/40/46LE600E/RU/S
4) ADC adjustment (Component 33K)
1

Adjustment point
Setting

Adjustment conditions
[Signal]
COMP 33K 50Hz 100% Full field
colour bar

Adjustment procedure
Feed the COMPONENT 33K 100% Full field colour bar (colour saturation
level 100%) signal to the CONPONENT video input of EXT3.

100% white

Black

[Terminal]
EXT3 CONPONENT input
2

Auto adjustment
performance

Adjustment process [COM ADJ]


menu page 6/8

Bring the cursor on [COM ADJ] and press OK key [*** OK ***] appears when finished.

5) PC signal adjustment (Analog D-SUB15pin)


1

Adjustment point
Setting

Adjustment conditions
[Signal]
XGA 60 Hz 100% Full field
colour bar

Adjustment procedure
Feed the XGA 60Hz 100% Full field colour bar (colour saturation level 100%)
signal to the EXT4 PC input.

100% white

Black

[Terminal]
EXT4 PC input
2

Auto adjustment
performance

Adjustment process [RGB ADJ]


menu page 7/8

Bring the cursor on [RGB ADJ] and press OK key [*** OK ***] appears when finished.

47

LC-32/40/46LE600E/RU/S
10. White Balance Adjustment
Adjustment gradation values (INFO) appear on page 8/8 3-4 lines of process adjustment, and adjustment initial values (offset value) appear on pages
8/8 5-10 lines. For white balance adjustment, adjust the offset values on pages 8/8 5-10 lines.
1. Preparation
1) Luminance meter reference device

:Minolta CA-210

2) Condition of the unit for adjustment and inspection:Modulated light: MAX (+16)
2. Setting
1) The luminance meter is set to the center of the screen of the set.
2) In INCH SIZE on the process adjustment page 1/8, sets it to the size of each panel with the

key to R/C.

3. Adjustment method
Check that the values of point A and B on page 8/8 of process adjustment are set as below. If not, change them accordingly.
WB Point A

1280

WB Point B

3712

1) Display the current adjustment status at point B. (Page 8/8 of process adjustment)
The display for checking the adjustment status is toggled by pressing the OK button on the remote control.
(Normal OSD display B display for check (OSD disappears) B normal OSD display ...)
2) Read the value of the luminance meter.
3) Change Point B ADJ R/Point B ADJ B (Adjustment offset value) on page 8/8 of process adjustment so that the values of the luminance meter
approach x = 0.272 and y = 0.277.
(Basically, Point B ADJ G is not changed.)
4) Follow Point A as well as item 3).
Change Point A ADJ R/Point A ADJ B (Adjustment offset value) on page 8/8 of process adjustment so that the values of the luminance meter
approach x = 0.272 and y = 0.277.
5) Select WB WRITE on page 8/8 in the process, set YES, and press the OK key of remote control.
The adjustment value is written. and then shut down the AC power.
*

Initial value of RGB of point B: 3712

Initial value of RGB of point A: based on calculated of each G point

6) [Adjustment value]
*

Teaching set send by engineering dept is set as reference

4. Adjustment reference standard value


Point A ref. value

Level
1280

Point B ref. value

3712

Adjustment spec 0.004


Adjustment spec 0.002

Spec Data
x=0.272
y=0.277
x=0.272
y=0.277

Adjustment Spec
0.001

Inspection Spec
0.002

0.002

0.004

Inspection spec 0.006 (point 1)


Inspection spec 0.004 (Excluding the above-mentioned)

48

LC-32/40/46LE600E/RU/S
11. QS Temperature NVM Data Confirmation
During servicing of the LCD TV set, by software upgrading or by any cleaning NVM, its mandatory select the INCH SIZE in Service Mode, Page 1,
according to the size of the TV set.

PAGE1/8
TV
32E_LE600E
Main Version
Boot Version
T-CON Version
CPLD Version
INCH SIZE
ERROR RESET
NO
STANDBY CAUSE 00 00 00 00 00
1) 00H 00M

PAGE1/8
TV
32E_LE600E
Main Version
Boot Version
T-CON Version
CPLD Version
INCH SIZE
32
ERROR RESET
NO
STANDBY CAUSE 00 00 00 00 00
1) 00H 00M

Default picture after cleaning NVM.

Picture with [Inch Setting] to 32.It is actually set as each inch.

12. Initialization to factory settings


After a factory setting, It ends with the AC power supply OFF.
After a factory settings, Do not turn on the power supply. If you turn on the power supply. execute the factory settings again.
Do not do power supply OFF by remote control.
CAUTION: When the factory settings have been made, all user setting data, including the channel settings, are initialized.
(The adjustments done in the adjustment process mode are not initialized.) Keep this in mind when initializing these settings.

Adjustment item
Factory settings

Adjustment conditions
Ends in AC power supply
OFF. (See to below caution)

Adjustment procedure
[Factory setting with adjustment process mode]
Enter the adjustment process mode.
Move the cursor to INDUSTRY INIT on page 2/8.
Use the / key of R/C to select a region from YES (E)/YES (I)/YES (F)/YES (R)
and press the [OK] key.
EXECUTING display appears and initialization starts.
After a while, OK display appears, the setting is completed.
When succeeding: The background color becomes green.
When failing: The background color becomes red.
NOTE: Never turn the power off during initialization.
When performing factory settings (while displaying page 2 of adjustment process), confirm
that the item INCH SIZE or the panel size displayed in the upper right corner corresponds
to each panel size.
The following items are initialized in the factory setting.
1) User settings
2) Channel data (e.g. broadcast frequencies)
3) Manufacturer option setting
4) Password data

After adjustments, exit the adjustment process mode.


To exit the adjustment process mode, turn off the MAIN power key.
When the power is turned off with the remote control, unplug the AC power cord and plug it back in.
(wait approximately 10 seconds before plugging in the AC power cord)

49

LC-32/40/46LE600E/RU/S
13. Functional explanation of STANDBY CAUSE
13.1. [display method]
It is displayed in the top page of the process adjustment mode. (Page displayed first when entering process mode)

13.2. [Content of display]


1. NORMAL STANDBY CAUSE
The reason that became a power-off by the specification of usual use and the main body is displayed.
(Only the one latest) It is not displayed when power supply OFF is carried out with remote control.
Display code
00
0x01
0x05
0x06
0x07
0x0A
0x0C
0x18

Display character string


00 00 00 00 00
1 RC_STANDBY
5 PC_OUT_OF_RANGE
6 NO_OPERATION
7 NO_SIGNAL
a SLEEP_TIMER
c RS232C
18 AV_LINK

Reason
When based on No error
When based on RC Standby OFF
When based on out of range for pc OFF
When based on non-operated OFF
When based on non-signal OFF
When based on an sleep-timer OFF
When based on the command from RS232C (standby)
When based on the command from AV-LINK (standby)

2. ERROR STANDBY CAUSE


When main CPU becomes a power-off detecting some abnormalities, the use time of the set at the time of the reason and the power-off is displayed five times.
When time information can be acquired from digital broadcasting, the date and time when the error occurs at the same time is recorded, displayed
and when time information cannot be acquired, it becomes the above-mentioned display.
00 is displayed when abnormality has not been detected even once.
Display error code
0x1A
0x1B
0x1C

Display character string


1a TEMP_ERROR
1b LAMP_ERROR
1c POWER_ERROR

Reason
When temperature (high temperature) is abnormal.
When lamp is abnormal
When power module is abnormal status.

14. Lamp error detection


1. Function description
This LCD colour television has a function (lamp error detection) to be turned OFF automatically for safety when the lamp or lamp circuit is abnormal.
If the lamp or lamp circuit is abnormal, or some other errors happen, and the lamp error detection is executed, the following occur.
1) The main unit of television is turned OFF about 5 seconds after it is turned ON.
(The power LED on the front side of TV turns from green to red.)
2) If the situation 1 happens 5 times sequentially, the power is turned on (relay is turned ON).
However, the backlight is not turned on, and then the relay is turned OFF after 5 to 6 seconds. (The power LED remains red.)
2. Countermeasures
When television is turned OFF by the lamp error detection mentioned above, it enters the adjustment process with the power LED red.
Entering the adjustment process, turns OFF the error detection and turns ON TV.
This enables the operation check to detect errors in the lamp or lamp circuit.
Check whether STANDBY CAUSE on line 7, page 1/8 of the adjustment process is 1B. it indicates the lamp error detection was executed.
After confirming that the lamp or lamp circuit is normal, reset the lamp error counter pushing OK in the R/C.
After resetting counter the green bar appears on Screen.
3. Reset standby cause error list
After confirming that the lamp error counter has been erased, select ERROR RESET, page 1/8 of the adjustment process and select YES using
the right cursor. For execute press OK in the R/C and the label ***OK*** appears on Screen.

4 10

LC-32/40/46LE600E/RU/S
15. Blinking display when error is detected
When system received error report, Standby LED (red) blinks as follows.
POWER LED should keep dark while error indication.
1) Lamp error
Blink timing (1 blink/1 period)

Light (H)
Dark (L)
1000ms

250ms
2) Power module error
Blink timing (2 blink/1 period)

250

250

3) High temperature
Blink timing (5 blink/1 period)

Light (H)
Dark (L)
250

250

250

250

250

250

4 11

250

1000ms

LC-32/40/46LE600E/RU/S
16. Upgrading the software
1. Unplug AC cable from outlet.
2. Insert an USB memory that is written a new software to USB port.
3. Keep pressing POWER button on LCD panel and plug AC cable to outlet.
4. POWER LED on panel automatically start blinking.
(POWER LED: Both red and green light blinking with sync. In other word, it looks, /blinking period is short ... 2 cycle - light - out - light - out / 1 sec.)
5. After a while (about 2 min.) following screen appears. Indicated percentage means progress of version up.

<SYSTEM UPGRADE>
System Version: EXXXXXXX

0%
STATUS
UPDATING...

6. After the progress becomes 100%, then STATUS area changes UPGRADE COMPLETE as followings (POWER LED: Only green blinks slowly ...
2 sec./time).

<SYSTEM UPGRADE>
System Version: EXXXXXXX

100%

OK

STATUS
UPGRADE COMPLETE

If above screen is not appeared and UPGRADE FAILURE is indicated in STATUS area, at that time update failure. Please repeat from step 1.
(POWER LED: Only red blinks slowly ... 2 sec./time).

<SYSTEM UPGRADE>
System Version: EXXXXXXX

50%

NG

STATUS
UPGRADE FAILURE

7. Unplug AC cable from outlet.


8. Remove USB memory from USB port.

4 12

LC-32/40/46LE600E/RU/S

CHAPTER 7. OVERALL WIRING/SYSTEM BLOCK DIAGRAM


LC32LE600E

Service Manual

[1] OVERALL WIRING DIAGRAM (LC-32LE600E/RU/S)

71

LC-32/40/46LE600E/RU/S

[2] OVERALL WIRING DIAGRAM (LC-40LE600E/RU/S)

72

LC-32/40/46LE600E/RU/S

[3] OVERALL WIRING DIAGRAM (LC-46LE600E/RU/S)

73

LC-32/40/46LE600E/RU/S

[4] SYSTEM BLOCK DIAGRAM (LC-32LE600E/RU/S)

74

LC-32/40/46LE600E/RU/S

[5] SYSTEM BLOCK DIAGRAM (LC-40LE600E/RU/S)

75

LC-32/40/46LE600E/RU/S

[6] SYSTEM BLOCK DIAGRAM (LC-46LE600E/RU/S)

76

LC-32/40/46LE600E/RU/S

CHAPTER 9. SCHEMATIC DIAGRAM


LC32LE600E

Service Manual

[1] DESCRIPTION OF SCHEMATIC DIAGRAM


1. VOLTAGE MEASUREMENT CONDITION:
1) The voltages at test points are measured on exclusive AC adaptor and the stable supply voltage of AC 220-240V. Signals are fed by a color bar signal generator for servicing purpose and the above voltages are measured with a 20k ohm/V tester.

2. INDICATION OF RESISTOR & CAPACITOR:


RESISTOR
1) The unit of resistance "" is omitted.
(K=k=1000, M=M).
2) All resistors are 5%, unless otherwise noted.
(K= 10%, F= 1%, D= 0.5%)
3) All resistors are 1/16W, unless otherwise noted.
CAPACITOR
1) All capacitors are F, unless otherwise noted.
(P=pF=F).
2) All capacitors are 50V, unless otherwise noted.
CAUTION:
This circuit diagram is original one, therefore there may be a slight
difference from yours.
SAFETY NOTES:
1) DISCONNECT THE AC PLUG FROM THE AC OUTLET
BEFORE REPLACING PARTS.
2) SEMICONDUCTOR HEAT SINKS SHOULD BE REGARDED AS
POTENTIAL SHOCK HAZARDS WHEN THE CHASSIS IS
OPERATING.
IMPORTANT SAFETY NOTICE:
PARTS MARKED WITH "
"(
) ARE IMPORTANT
FOR MAINTAINING THE SAFETY OF THE SET. BE SURE TO
REPLACE THESE PARTS WITH SPECIFIED ONES FOR MAINTAINING THE SAFETY AND PERFORMANCE OF THE SET.

91

LC-32/40/46LE600E/RU/S

[2] SCHEMATIC DIAGRAM


1. MAIN Unit-1

10

11

92

12

13

14

15

16

17

18

19

20

21

LC-32/40/46LE600E/RU/S
2. MAIN Unit-2

10

11

93

12

13

14

15

16

17

18

19

20

21

LC-32/40/46LE600E/RU/S
3. MAIN Unit-3

10

11

94

12

13

14

15

16

17

18

19

20

21

LC-32/40/46LE600E/RU/S
4. MAIN Unit-4

10

11

95

12

13

14

15

16

17

18

19

20

21

LC-32/40/46LE600E/RU/S
5. MAIN Unit-5

10

11

96

12

13

14

15

16

17

18

19

20

21

LC-32/40/46LE600E/RU/S
6. MAIN Unit-6

10

11

97

12

13

14

15

16

17

18

19

20

21

LC-32/40/46LE600E/RU/S
7. MAIN Unit-7

10

11

98

12

13

14

15

16

17

18

19

20

21

LC-32/40/46LE600E/RU/S
8. MAIN Unit-8

10

11

99

12

13

14

15

16

17

18

19

20

21

LC-32/40/46LE600E/RU/S
9. MAIN Unit-9

10

11

9 10

12

13

14

15

16

17

18

19

20

21

LC-32/40/46LE600E/RU/S
10. MAIN Unit-10

10

11

9 11

12

13

14

15

16

17

18

19

20

21

LC-32/40/46LE600E/RU/S

9 12

LC-32/40/46LE600E/RU/S

CHAPTER 6. MAJOR IC INFORMATIONS Service


LC32LE600E

Manual

[1] MAJOR IC INFORMATIONS


1. DESCRIPTION OF MAJOR ICs
Ref No.
Name
[MAIN UNIT]
IC1301
VHiAK4341ED-1Y

Part Code
DAC

IC1302

VHiMT8292N+-1Q

Audio multiplexer

IC1303

VHiS80944NM-1Y

IC1104

VHiPQ1LA505-1Y

Voltage detector with builtin delay circuit


ANT5V-REG

IC501

1K E2PROM

IC506

VHi2BR24C21F-1Y
for service
(RH-iXC206WJQZS)
VHiM3221EiP-1Y

IC1508

VHiSii91873-1Q

HDMI_Port _Processor

IC3302

VHiBD6538G+-1Y

USB high side SW

IC3303

RH-iXC758WJQZQ

VCT & Main CPU

IC3304

VHiS80928NM-1Y

IC3305

VHiS80920NM-1Y

IC3501/2

RH-iXC505WJQZQ

Voltage detector with builtin delay circuit


Voltage detector with builtin delay circuit
512Mb-DDR2-SDRAM

IC8403

RH-iXC788WJN2Y

2Mb-Serial-FLASH

IC8401

RH-iXC721WJQZQ

512Mb-NAND-FLASH

IC8455

VHiBR24S64F-1Y

I2C bus type-64K


E2PROM

IC4402

VHiAOZ1320C-1Y

SMART LOAD SW

RS232C-DRIVER

Description
AK4341 is 24 bits DAC of 2Vrms output. A newly developed advanced multiple bit
system is adopted in the
modulator. In this model, this IC is used to use the
audio signal from a digital tuner as an audio output signal of SCART1.
The MediaTek MT8292 introduces the advantages of an input multiplexer, the
headphone driver and the PGA outputs. The analog input pins can either independently support GPIO function or provide extra GPIO pins to use. The analog
input pins can either independently support GPIO function or provide extra GPIO
pins to use.
This IC is a highly precision voltage detector (4.4V) with built-in delay circuit.
In this model, It used as voltage detector of MUTE signal.
PQ1LA505 is series regurator with an on/off function and the over current protection function.
In this model, it generate 5V.
This IC is a 1Kbit-2-wire (I2C bus type) serial EEPROM that can be programmed
electrically. The EEPROM chip stores the EDID data of PC input. This data is
controlled through I2C signals.
The MAX3221E is a single driver, single receiver RS-232 solution operating from
a single Vcc supply. The RS-232 pins provide IEC G1000-4-2 ESD Protection.
The device meets the requirements of TIA/EIA-232-F and provides the electrical
interface between an asynchronous communication controller and the serial-port
connector.
The charge pump and four small external capacitors allow operation from a single
3V to 5.5V supply.
The SiI91873 HDMI port processor is the second generation of HDMI devices
that support revision 1.3 of the HDMI specification.
The main feature is as follows.
1) 4-input, 1-output HDMI port processor.
2) Integrated TMDS receiver and transmitter cores capable of receiving and
transmitting at 2.25Gbps.
3) Supports video resolutions up to 1080p, 60Hz, 12bit or 720p/1080i,
120Hz,12bit.
4) Receiver fully comply with DVI1.0, HDCP1.1 and HDMI1.3 specifications.
BD6538G is single channel high side powers switch with low ON resistance Nch
power MOSFET.
Rich safety functions such as over current detection, Thermal shutdown (TSD),
under voltage lock out (UVLO) and soft start function which are required for the
power supply port protection are integrated into 1chip.
This IC is Video Processor & MAIN CPU.
In this IC, the decode processing and the video signal processing are done.
Moreover, OSD is generated here and added to a picture signal.
This IC is a highly precision voltage detector (2.8V) with built-in delay circuit. In
this model, It uses as RESET signal of IC3303.
This IC is a highly precision voltage detector (2.0V) with built-in delay circuit. In
this model, It used as a D-POW signal generator.
This IC is 512Mb DDR2 SDRAM.
This IC operates as a memory of IC3303 (Video Processor). ***
This IC is 2Mbit CMOS 3.0 Volt Flash Memory with 50-MHz SPI (Serial Peripheral
Interface) Bus and Small Sector for Boot and Parameter Storage.
This IC is 512Mb NAND flash memory.
This IC stores the software data that processes the system of TV such as the
graphic processing, the LCD controls, and backlights etc.
The BR24S64F is a 64Kbit-2-wire (I2C bus type) serial EEPROM that can be programmed electrically.
This IC stores the menu data and the adjustment value data of adjustment process mode etc.
The data is given out by commands from the main microprocessor.
The AOZ1320 is a P-channel high-side load switch with controlled slew rate.
AOZ1320-04 have a slew rate of 1ms.

61

LC-32/40/46LE600E/RU/S
Ref No.
IC4401

Name
VHiMT8295AE-1Q

Part Code
CI_controller

IC2701

VHiYDA148QZ-1Y

A-AMP

IC9612

VHiTCR5SB33-1Y

1CH-SW-REG
BU3.3V-REG

IC9614

VHiS80928NM-1Y

IC9605

VHiLV5893M+-1Y

IC9611

VHiTCR5SB25-1Y

Voltage detector with builtin delay circuit


1CH-SW-REG
D3.3V-REG
1CH-SW-REG
2.5V-REG

IC9608

VHiLV5893M+-1Y

IC9604

VHiLV58072M-1Y

IC9606

VHiLV5805M+-1Y

IC9603

VHiMM3141YN-1Y

1CH-SW-REG
D5V-REG
1CH-SW-REG
D1.1V-REG
1CH-SW-REG
D1.8V-REG
CPU1.25V-REG

IC9610

VHiPQ1LAX95-1Y

S9V-REG

IC2602
VHiHC2G66DP-1Y
IC9601
IC9613
[POWER UNIT]
IC7102
TNY274PN

IC7101

UCC28061

IC7200

NCP1606B

IC7104

SSC9502S

IC7505

FA5573

IC7101

VIPER17

IC7001

L6562A

IC7002

FA5538

IC7251

FA5511

Bilateral Switch

BU5V
SW-REG-CTL
for 40/46
UR13V
P-FACTOR
for 46
UR13V
P-FACTOR
for 40
UR13V
SW-REG-CTL for 40/46
VLCD
LOW-STANDBY
for 40/46
BU5V
SW-REG-CTL
for 32
UR13V
P-FACTOR
for 32
UR13V
SW-REG-CTL for 32
VLCD
SW-REG-CTL for 32

Description
This is a control IC for PCMCIA cards. This controls information on IC cards
inserted into the PCMCIA card slot (SC4401) or information on software version
upgrade cards saved on flash memories to transfer the data to CPUs and memories.
This IC is a digital audio power amplifier. It is mounted by 32QFN small package
with 15W or less stereo. it drives by 10W in 26, and 32 types.
The TCR5SB33 is CMOS general-purpose single-output voltage regulators with
an on/off control input, featuring low dropout voltage and low quiescent bias current. The output current is possible up to 200mA or less. In this model, it generate
BU3.3V.
This IC is a highly precision voltage detector(2.8V) with built-in delay circuit.
In this model, It used as enable signal of BU3.3V_REG.
LV5893M is 1.8A 1ch step down switching regulator.
In this model, it generate D3.3V.
The TCR5SB25 is CMOS general-purpose single-output voltage regulators with
an on/off control input, featuring low dropout voltage and low quiescent bias current. The output current is possible up to 200mA or less. In this model, it generate
CPU2.5V.
LV5893M is 1.8A 1ch step down switching regulator.
In this model, it generate D5V.
LV58072M is 3A 1ch step down switching regulator.
In this model, it generate D1.1V.
LV5805M is 2A 1ch step down switching regulator.
In this model, it generate D1.8V.
MM3141 is single-output voltage regulators with an on/off control input.
In this model, it generate CPU1.25V.
PQ1LAX95 is the low power loss regulator equipped with the on/off function and
the over current protection function. In this model, it generate S9V.
This IC is provides a dual analog switch. Each switch has two pins for input or
output and an active HIGH enable input.

This IC is IC for the switching regulator with Enhanced Flexibility and Extended
Power Range
In this model, non-reg BU5V power supply is generated.
This IC is IC that improves Power-Factor in 13V_Regulator circuit of 46 type
power supply circuit.
The protection functions such as UVLO, Brounout, OVP and AOC are built into in
this IC.
This IC is IC that improves Power-Factor in 13V_Regulator circuit of 40 type
power supply circuit.
The protection functions such as UVLO, Brounout, OVP and AOC are built into in
this IC.
This IC is switching power supply IC of a monolithic type.
In this model, non-reg UR13V power supply is generated.
This IC is IC for the low standby power requirement type switching power supply
control.
In this model, backlight LED power supply (VLED=187/209V) is generated.
This IC is switching power supply IC of the off-line converter type with a PWM
control.
In this model, non-reg BU5V power supply is generated.
This IC is IC that improves Power-Factor in 13V_Regulator circuit of 32 type
power supply circuit.
The protection functions such as UVLO, Brounout, OVP and AOC are built into in
this IC.
This IC is switching-power-supply control IC of the current mode system where
power MOSFET drives directly. In this model, UR13V (32 types) is generated.
This IC is IC for the PWM type switching power supply control.
In this model, backlight LED power supply (VLED=144V) is generated.

62

LC-32/40/46LE600E/RU/S
2. Detailed ICs Information
2.1. IC1301 (VHiAK4341ED-1Y)
2.1.1 Block Diagram

2.1.2 Pin Connections and short description


Pin No.
1
2
3
4
5

Pin Name
MCLK
BICK
SDTI
LRCK
RDN

I/O
I
I
I
I
I

SMUTE

ACKS

DIF

DEM

10

AOUTR

11

AOUTL

12

HVDD

13
14
15

VSS
VDD
VCOM

16

GAIN

Pin Function
Master clock input pin. An external TTL clock should be input on this pin.
Audio serial data clock pin.
Audio serial data input pin.
L/R clock pin.
Power-down mode pin.
When at L, the AK4341 is in the power-down mode, held in reset and AOUTL/R are held in VCOM.
The AK4341 must be reset once upon power-up.
Soft mute pin in parallel control mode.
H: Enable, L: Disable
Auto setting mode pin.
L: Manual setting mode, H: Auto setting mode.
Audio data interface format pin.
L: 24bit MSB justified, H; I2S.
De-emphasis enable pin.
H: Enable, L: Disable
Rch analog output pin.
When PDN pin = L, outputs VCOM voltage.
Lch analog output pin.
When PDN pin = L, outputs VCOM voltage.
Output buffer power supply pin.
Normally connected to VSS with a 0.1F ceramic capacitor in parallel with a 10F electrolytic cap.
Ground pin.
DAC power supply pin.
DAC common voltage pin.
Normally connected to VSS with a 10F electrolytic cap.
Outputs VCOM VDD voltage either PDN pin = L or H.
Gain control pin.
H: +6dB, L: 0dB, open: +12dB.
When PDN = H, the gain pin is connected to VDD and VSS with 50k resister and held to VDD/2 when open.
When PDN = L, connected to VSS with 50k resister.

63

LC-32/40/46LE600E/RU/S
2.2. IC1302 (VHiMT8292N+-1Y)
2.2.1 Block Diagram

64

LC-32/40/46LE600E/RU/S
2.2.2 Pin Connections and short description
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56

Pin Name
AIN8R
AIN8L
MVDD33
VCM33
MGND33
ADCOUTL
ADCOUTR
HPOUTL
HPGND
HPVDD
HPOUTR
AGND
PGA0OUTL
PGA0OUTR
AVDD
VCMPGA
PGA2OUTL
PGA2OUTR
PGA1OUTL
PGA1OUTR
INPUT2R
INPUT2L
INPUT0R
INPUT0L
INPUT1R
INPUT1L
CL
DI
MUTE#
RESET#
GPIO0
GPIO1
GPIO2
GPIO3
GPIO4
DVDD
DGND
GPIO5
GPIO6
GPIO7
GPIO8
GPI
AIN1R
AIN1L
AIN2R
AIN2L
AIN3R
AIN3L
AIN4R
AIN4L
AIN5R
AIN5L
AIN6R
AIN6L
AIN7R
AIN7L

I/O
I
I

O
O
O

O
O

O
O
O
O
O
I
I
I
I
I
I
I
I/O
I
I
I
I
I
I
I

I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I

Pin Function
Channel 8 right input.
Channel 8 left input.
Multiplexer positive supply 3.3 voltage.
Multiplexer midrail divider de coupling pin.
Multiplexer negative supply.
Analog multiplexer left output.
Analog multiplexer right output.
Headphone right channel output.
Headphone ground supply pin.
Headphone power supply pin.
Headphone right channel output.
Analog negative supply.
PGA channel 0 left output.
PGA channel 0 right output.
Analog positive supply 12 voltage or 9 voltage.
PGA midrail divider de coupling pin.
PGA channel 2 left output.
PGA channel 2 right output.
PGA channel 1 left output.
PGA channel 1 right output.
Channel 2 right input to PGA gain module.
Channel 2 left input to PGA gain module.
Channel 0 right input to PGA gain module.
Channel 0 left input to PGA gain module.
Channel 1 right input to PGA gain module.
Channel 1 left input to PGA gain module.
Control clock pin in serial mode.
Control data pin in serial mode.
Hardware mute function when this pin is driven low.
The device enters a low power mode when this pin is driven low.
General Purpose I/O 0 and also shares hardware trapped function.
General Purpose I/O 1.
General Purpose I/O 2.
General Purpose I/O 3.
General Purpose I/O 4.
Digital positive supply 3.3 voltage.
Digital negative supply.
General Purpose I/O 5.
General Purpose I/O 6.
General Purpose I/O 7.
General Purpose I/O 8.
Only General Purpose Input and support internal digital scan mode.
Channel 1 right input (default).
Channel 1 left input (default).
Channel 2 right input.
Channel 2 left input.
Channel 3 right input.
Channel 3 left input.
Channel 4 right input.
Channel 4 left input.
Channel 5 right input.
Channel 5 left input.
Channel 6 right input.
Channel 6 left input.
Channel 7 right input.
Channel 7 left input.

65

sheet name
open
open

C-GND
GND
AUDIO_IN_L
AUDIO_IN_R
HP_L
GND
S9V
HP_R
GND
open
open
S9V
C-GND
SPK_OUT_L
SPK_OUT_R
MONITOR_L
MONITOR_R
AOUT_SP_R
AOUT_SP_L
AOUT_HP_R
AOUT_HP_L
AOUT_MONI_R
AOUT_MONI_L
SCLO_400K
SDAO_400K
AUSW_MUTE
AUSW_RST
R-GND
open
open
COMP_PLUG
MUTE_A_ALL
D3.3V
ground
open
open
TUNER_OUT_SEL
TUNER_OUT_CVBS_MUTE
CVBS_PLUG
SC1_IN_R
SC1_IN_L
SC2_IN_R
SC2_IN_L
COMP_IN_R
COMP_IN_L
RC/HDMI_IN_R
RC/HDMI_IN_L
CVBS_IN_R
CVBS_IN_L
open
open
open
open

LC-32/40/46LE600E/RU/S
2.3. IC1303, IC9607 (VHiS80944NM-1Y)
2.3.1 Block Diagram

2.3.2 Pin Connections and short description


Pin No.
1
2
3
4
5

Pin Name
OUT
VDD
VSS
NC
CD

I/O
O

Pin Function
Voltage detection output terminal (RESET detecting voltage).
Voltage input terminal.
Ground terminal.
No connection (It is an opening electrically.)
External capacitor connection terminal for delay.

66

LC-32/40/46LE600E/RU/S
2.4. IC1104 (VHiPQ1LA505-1Y)
2.4.1 Block Diagram

2.4.2 Pin Connections and short description


Pin No.
1
2
3
4
5

Pin Name
Nr
GND
Vc
Vin
Vo

I/O
I
I
I
O

Pin Function
Noise Control
Ground pin
ON/OFF Control
DC input
DC Output

67

LC-32/40/46LE600E/RU/S
2.5. IC501 (VHiBR24C21F-1Y)
This IC is a block diagram and description LC-32/40/46LE700E (S89B4LC32L700) please see the service manual.

2.6. IC506 (VHiM3221EiP-1Y)


This IC is a block diagram and description LC-32/40/46LE700E (S89B4LC32L700) please see the service manual.

2.7. IC1508 (VHiSii91873-1Q)


2.7.1 Block Diagram

68

LC-32/40/46LE600E/RU/S
2.7.2 Pin Connections and short description
Pin No.
Pin Name
HDMI RX Port Pins
68
R0X0P
67
R0X0N
70
R0X1P
69
R0X1N
72
R0X2P
71
R0X2N
66
R0XCP
65
R0XCN
4
R1X0P
3
R1X0N
6
R1X1P
5
R1X1N
8
R1X2P
7
R1X2N
2
R1XCP
1
R1XCN
14
R2X0P
13
R2X0N
16
R2X1P
15
R2X1N
18
R2X2P
17
R2X2N
12
R2XCP
11
R2XCN
22
R3X0P
21
R3X0N
24
R3X1P
23
R3X1N
26
R3X2P
25
R3X2N
20
R3XCP
19
R3XCN
HDMI Tx Port Pins
60
TX0P
61
TX0N
58
TX1P
59
TX1N
56
TX2P
57
TX2N
62
TXCP
63
TXCN
System Switching Pins
29
DSDA0
33
DSDA1
39
DSDA2
43
DSDA3
30
DSCL0
34
DSCL1
40
DSCL2
44
DSCL3
32
R0PWR5V
36
R1PWR5V
42
R2PWR5V
46
R3PWR5V
31
HPD0
35
HPD1
41
HPD2
45
HPD3
49
R4PWR5V

I/O

Pin Function

I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I

TMDS input port 0 data pairs.

O
O
O
O
O
O
O
O

HDMI Tx Output port data.


TMDS Low Voltage Differential Signal output data pairs.

I/O
I/O
I/O
I/O
I
I
I
I

O
O
O
O

DDC I2C Data for respective port. These signals are true open drain, and do not pull-down to ground when
power is not applied to the device. These pins require an external pull-up resistor.

TMDS input port 0 clock pair.


TMDS input port 1 data pairs.

TMDS input port 1 clock pair


TMDS input port 2 data pairs.

TMDS input port 2 clock pair.


TMDS input port 3 data pairs.

TMDS input port 3 clock pair

DDC I2C Clock for respective port. These signals are true open drain, and do not pull-down to ground when
power is not applied to the device. These pins require an external pull-up resistor.

5-V Port detection input for respective port. Connect to 5-V signal from HDMI input connector.

Hot Plug Detect Output for respective port. Connect to HOTPLUG of HDMI input connector.

5V power from 5th Rx port.

69

LC-32/40/46LE600E/RU/S
Pin No.
Pin Name
Control Pins
54
CSCL

I/O

Pin Function

Local Configuration/Status I2C Clock. Chip configuration/status is accessed via this I2C port.
This pin is a true open drain, so it does not pull to ground if power is not applied.
Local Configuration/Status I2C Data. Chip configuration/status is accessed via this I2C port.
This pin is a true open drain, so it does not pull to ground if power is not applied.
DDC I2C Clock for VGA port. HDCP KSV, Aa, and Ri values are exchanged over this I2C port during authentication. This pin is a true open drain, so it does not pull to ground if power is not applied.
The R4PWR5V (VREF) pad will provide a reference voltage for the PROT input pin.
DDC I2C Data for VGA port. HDCP KSV, Aa, and Ri values are exchanged over this I2C port during authentication. This pin is a true open drain, so it does not pull to ground if power is not applied.
The R4PWR5V (VREF) pad will provide a reference voltage for the PROT input pin.

53

CSDA

I/O

48

DSCL4

47

DSDA4

I/O

Configuration Pins
55
TPWR_CI2CA

I/O

52

INT

10

RSVD

28
RSVD
CEC Pins
50
CEC_A

51

I/O

CEC_D

I/O

Power and Ground Pins


9,27,64 VCC33
37
MICOM_VCC33

38

ePad

SBVCC

Epad

I2C Slave Address input/Transmit Power Sense Output. When RESET# is LOW, this pin is used as an input
to latch the I2C sub _address. The level on this pin is latched when the RESET# pin transition from LOW to
HIGH. When RESET# is HIGH, this pin is used as the TPWR output, indicating that the receive port has 5V
present.
Interrupt Output.
This is an open_drain output and requires an external pull_up resister.
When SBVCC (pin38) = 5V, RSVD pin #10 must be tied to GND with less than 10K resistor.
When SBVCC (pin38) = 3.3V, RSVD pin #10 must be tied to GND with 1M ohm resistor.
These pins must be tied to GND during normal operation.
HDMI compliant CEC I/O used for interfacing to CEC devices. The signal is electrically compliant with CEC
specification. This pin connects to the CEC signal of all HDMI connectors in the system. As an input, the pin
acts as a LVTTL, Schmitt triggered input and is 5V tolerant. As an output, the pin acts as an NMOS driver
with resistive pull-up. This pin has an internal pull-up resistor.
This pin is configurable through NVRAM. For CEC_D use, this pin interfaces to the CEC master. Usually
connected to Micro-controller.
TMDS Core VCC. Must be supplied at 3.3V
During normal mode, this pin provides 3.3V power to external micro-controller. Maximum output current is
30mA.
Local Power from TV.
When SBVCC (pin38) = 5V, RSVD pin #10 must be tied to GND with less than 10K resistor.
When SBVCC (pin38) = 3.3V, RSVD pin #10 must be tied to GND with 1M ohm resistor.
ePad must be connected to ground.
All ground planes, analog and digital, must be tied together to the ePad, which must be connected to ground.

6 10

LC-32/40/46LE600E/RU/S
2.8. IC3302 (VHiBD6538G+-1Y)
2.8.1 Block Diagram

2.8.2 Pin Connections and short description


Pin No.
1

Pin Name
VIN

I/O
I

2
3

GND
EN

/OC

VOUT

Pin Function
Power supply input terminal.
It is an input terminal to the switch and a power supply input terminal of an internal circuit.
Ground
Switch enable input terminal.
The switch is turned on by inputting the high level.
Over current notification terminal.
When the over current is detected, it becomes a low level.
Open drain output.
Switch output terminal.

6 11

LC-32/40/46LE600E/RU/S
2.9. IC3304 (VHiS80928NM-1Y), IC3305 (VHiS80920NM-1Y)
2.9.1 Block Diagram

2.9.2 Pin Connections and short description


Pin No.
1
2
3
4
5

Pin Name
OUT
VDD
VSS
NC
CD

I/O
O

Pin Function
Voltage detection output terminal. (RESET detecting voltage)
Voltage input terminal.
Ground terminal.
No connection (It is an opening electrically.)
External capacitor connection terminal for delay.

6 12

LC-32/40/46LE600E/RU/S
2.10. IC3501, IC3502 (RH-iXC505WJQZQ)
2.10.1 Block Diagram

2.10.2 Pin Connections and short description


Pin No.
J8, K8

Pin Name
CK, CK#

I/O
I

K2

CKE

L8

CS#

Pin Function
Clock:
CK and CK# are differential clock inputs. All address and control input signals are sampled on the
crossing of the positive edge of CK and negative edge of CK#.
Output (read) data is referenced to the crossings of CK and CK# (both directions of crossing).
Clock Enable:
CKE HIGH activates, and CKE Low deactivates, internal clock signals and device input buffers and
output drivers.
Taking CKE Low provides Pre charge Power-Down and Self Refresh operation (all bank idle), or
Active Power-Down (row Active in any bank).
CKE is synchronous for power down entry and exit, and for self refresh entry. CKE is asynchronous for self refresh exit.
After VREF has become stable during the power on and initialization sequence, it must be maintained for proper operation of the CKE receiver. For proper self-refresh entry and exit, VREF must
be maintained to this input.
CKE must be maintained high throughout read and write accesses. Input buffers, excluding CK,
CK#, ODT and CKE are disabled during power-down. Input buffers, excluding CKE are disabled
during self refresh.
Chip Select:
All commands are masked when CS# is registered HIGH.
CS# provides for external bank selection on systems with multiple banks.
CS# is considered part of the command code.

6 13

LC-32/40/46LE600E/RU/S
Pin No.
K9

K7, L7, K3

Pin Name
ODT

I/O
I

Pin Function
On Die Termination:
ODT (registered HIGH) enables termination resistance internal to the DDR2 SDRAM.
When enabled, ODT is only applied to each DQ, DQS, DQS#, RDQS, RDQS#, and DM signal for
x4/x8 configuration.
For x16 configuration, ODT is applied to each DQ, UDQS/UDQS#.
LDQS/LDQS#, UDM and LDM signal.
The ODT pin will be ignored if the Extended Mode Register Set (EMRS) is programmed to disable
ODT.
Command Inputs:
RAS#, CAS# and WE# (along with CS#) define the command being entered.
Input Data Mask:
DM is an input mask signal for write data. Input data is masked when DM is sampled HIGH coincident with that input data during a Write access.
DM is sampled on both edges of DQS. Although DM pins are input only, the DM loading matches
the DQ and DQS loading. For x8 device, the function of DM or RDQS/RDQS# is enabled by EMRS
command.
Bank Address Inputs:
BA0 and BA1 define to which bank an Active, Read, Write or Pre charge command is being
applied.
Bank address also determines if the mode register or extended mode register is to be accessed
during a MRS or EMRS cycle.
Address Inputs: Provide the row address for Active commands, and the column address and Auto
Pre charge bit for Read/Write commands to select one location out of the memory array in the
respective bank.
A10 is sampled during a pre charge command to determine whether the PRECHARGE applies to
one bank (A10 LOW) or all banks (A10 HIGH).
If only one bank is to be pre charged, the bank is selected by BA0, BA1. The address inputs also
provide the op-code during a Mode Register Set command.
Data Input/Output: Bi-directional data bus.

RAS#, CAS#,
WE#
DM
(UQM3) (DQM1)
or
(UQM2) (DQM3)

L2, L3

BA0, BA1

M8, M3, M7, N2,


N8, N3, N7, P2,
P8, P3, M2, P7,
R2

A [0:12]

G8, G2, H7, H3,


H1, H9, F1, F9,
C8, C2, D7, D3,
D1, D9, B1, B9
B7, A8, F7, E8

DQ [0:15]
or
DQ [16:31]

I/O

(DQS1), (DQS1#)
(DQS0), (DQS0#)
or
(DQS3), (DQS3#)
(DQS2), (DQS2#)

I/O

A2, E2, L1, R3,


R7, R8
A1, E1, J9, M9,
R1
A9, C1, C3, C7,
C9, E9, G1, G3,
G7, G9
A3, E3, J3, N1,
P9
A7, B2, B8, D2,
D8, E7, F2, F8,
H2, H8
J1
J7
J2

NC

Data Strobe:
Output with read data, input with write data. Edge-aligned with read data, centered in write data.
For the x16, DQS1 corresponds to the data on DQ0>DQ7; DQS0 corresponds to the data on
DQ8>DQ15.
For the x8, an DQS2 option using DM pin can be enabled via the EMRS (1) to simply read timing.
The data strobes DQS1, DQS0, DQS3, and DQS2 may be used in single ended mode or paired
with optional complementary signals DQS1#, DQS0#, DQS3# and DQS2# to provide differential
pair signaling to the system during both reads and writes. A control bit at EMRS (1) [A10] enables
or disables all complementary data strobe signals.
In this data sheet, differential DQS signals refers to any of the following with A10=0 of EMRS (1)
x4 DQS1/DQS1#
x8 DQS1/DQS1# if EMRS (1) [A11] =0
x8 DQS1/DQS1#, DQS2/DQS2#
x16 DQS0/DQS0# and DQS3/DQS3#
No Connect: No internal electrical connection is present.

VDD

Power Supply: +1.8V 0.1V.

VDDQ

DQ Power Supply: +1.8V 0.1V.

VSS

Ground.

VSSQ

Ground. DQ Ground.

VDDL
VSSDL
VREF

DLL Power Supply: +1.8V 0.1V.


DLL Ground.
Reference voltage for inputs for SSTL interface.

F3, B3

6 14

LC-32/40/46LE600E/RU/S
2.11. IC8403 (RH-iXC788WJZZY)
2.11.1 Block Diagram

2.11.2 Pin Connections and short description


Pin No.
1

2
3

4
5
6

Pin Name
CS#
(Chip Select)

I/O
I

SO
(Signal data Output)
W#
(Write Protect)

GND
SI
(Serial Data Input)
SCK
(Serial Clock)

HOLD#

VCC

Pin Function
Places device in active power mode when driven low.
Deselects device and places SO at high impedance when high.
After power-up, device requires a falling edge on CS# before any command is written.
Device is in standby mode when a program, erase, or Write Status Register operation is not in progress.
Transfers data serially out of the device on the falling edge of SCK.
Protects the memory area specified by Status Register bits BP2:BP0.
When driven low, prevents any program or erase command from altering the data in the protected memory area.
Ground
Transfers data serially into the device. Device latches commands, addresses, and
program data on SI on the rising edge of SCK.
Provides serial interface timing.
Latches commands, addresses, and data on SI on rising edge of SCK.
Triggers output on SO after the falling edge of SCK.
Pauses any serial communication with the device without deselecting it. When driven low, SO is at high
impedance, and all input at SI and SCK are ignored. Requires that CS# also be driven low.
Supply Voltage

6 15

LC-32/40/46LE600E/RU/S
2.12. IC8401 (RH-iXC721WJQZQ)
2.12.1 Block Diagram

6 16

LC-32/40/46LE600E/RU/S
2.12.2 Pin Connections and short description
Pin No.
29-44

Pin Name
IO0-IO7

I/O
I/O

16

CLE

17

ALE

CE#

18

WE#

RE#

19

WP#

A/B#

37

VCC

36
1-6, 10-11, 14-15,
20-28, 33-35,
39-40, 45-48

VSS
NC

Pin Function
DATA INPUTS/OUTPUTS
The IO pins allow to input command, address and data and to output data during read/program operations.
The inputs are latched on the rising edge of Write Enable (WE#).
The I/O buffer float to High-Z when the device is deselected or the outputs are disabled.
COMMAND LATCH ENABLE
This input activates the latching of the IO inputs inside the Command Register on the Rising edge of Write
Enable (WE#).
ADDRESS LATCH ENABLE
This input activates the latching of the IO inputs inside the Address Register on the Rising edge of Write
Enable (WE#).
CHIP ENABLE
This input controls the selection of the device. When the device is busy CE# low does not deselect the
memory.
WRITE ENABLE
This input acts as clock to latch Command, Address and Data. The IO inputs are latched on the rise edge
of WE#.
READ ENABLE
The RE# input is the serial data-out control, and when active drives the data onto the I/O bus. Data is valid
REA after the falling edge of RE# which also increments the internal column address counter by one.
WRITE PROTECT
The WP# pin, when Low, provides an Hardware protection against undesired modify (program/erase)
operations.
READY BUSY
The Ready/Busy output is an Open Drain pin that signals the state of the memory.
SUPPLY VOLTAGE
The VCC supplies the power for all the operations (Read, Write, Erase).
GROUND
NO CONNECTION

2.13. IC8455 (VHiBR24S64F-1Y)


This IC is a block diagram and description LC-32A47E/RU/V (S59Z4LC32A47E) please see the service manual.

6 17

LC-32/40/46LE600E/RU/S
2.14. IC4402 (VHiAOZ1320C-1Y)
2.14.1 Block Diagram

2.14.2 Pin Connections and short description


Pin No.
1

Pin Name
OUT

I/O
O

2
3

GND
EN

NC

5
6

GND
IN

Pin Function
Output.
OUT is the source of the P-channel MOSFET.
Ground
Enable.
The P-channel MOSFET turns on when EN is logic HIGH.
No connect.
This pin is not internally connected.
Ground
Input.
IN is the drain of the P-channel MOS FET. It is the supply input of the IC.

6 18

LC-32/40/46LE600E/RU/S
2.15. IC4401 (VHiMT8295AE-1Q)
2.15.1 Block Diagram

2.15.2 Pin Connections and short description


Pin No.
Pin Name
Miscellaneous
107
RESETB
114
CI_INT
NAND flash
116
CI_DATA0
115
CI_DATA1
95
CI_DATA2
102
CI_DATA3
101
CI_DATA4
100
CI_DATA5
99
CI_DATA6
98
CI_DATA7
94
CI_CEB

I/O

Pin Function

Sheet Name

I
O

Chip reset.
interrupt.

CI_CNT_RESET
CI_CNT_INT

I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I

NAND Flash Data bit 0.


NAND Flash Data bit 1.
NAND Flash Data bit 2.
NAND Flash Data bit 3.
NAND Flash Data bit 4.
NAND Flash Data bit 5.
NAND Flash Data bit 6.
NAND Flash Data bit 7.
NAND Flash Chip enable.

PDD0_
PDD1_
PDD2_
PDD3_
PDD4_
PDD5_
PDD6_
PDD7_
CI_CE#

6 19

LC-32/40/46LE600E/RU/S
Pin No.
Pin Name
106
CI_RB
96
CI_WEB
103
CI_ALE
105
CI_CLE
117
CI_OEB
CLK/Crystal
109
XTALO
110
XTALI
Transport stream (TS)
6
TOCLK
7
TOSYNC
8
TOVALID
9
TODATA0
11
TODATA1

I/O
O
I
I
I
I

Pin Function
NAND Flash Ready.
NAND Flash Write enable.
NAND Flash Address Latch enable.
NAND Flash Command Latch enable.
NAND Flash Output enable.

Sheet Name
N_PARB_
XEWE_
PAALE_
PACLE_
XERE_

O
I

Crystal output.
Crystal input.

XTAL_O
XTAL_I

I
I
I
I
I

Transport stream 1 input clock.


Transport stream 1 input sync.
Transport stream 1 input valid.
Transport stream 1 input data bit 0.
Transport stream 1 input data bit 1.
Transport stream 2 input clock.
12
TODATA2
I
Transport stream 1 input data bit 2.
Transport stream 2 input sync.
13
TODATA3
I
Transport stream 1 input data bit 3.
Transport stream 2 input valid.
14
TODATA4
I
Transport stream 1 input data bit 4.
Transport stream 2 input data.
16
TODATA5
I
Transport stream 1 input data bit 5.
17
TODATA6
I
Transport stream 1 input data bit 6.
18
TODATA7
I
Transport stream 1 input data bit 7.
123
TS_CKO
O
Transport stream output clock.
125
TS_SYNCO
O
Transport stream output sync.
122
TS_VALIDO
O
Transport stream output valid.
124
TS_DATAO
O
Transport stream output data.
General Purpose Input and Output (GPIO)
1
GPIO0
I/O
General purpose I/O bit 0. (Resister-Ground)
2
GPIO1
I/O
General purpose I/O bit 1. (Resister-Ground)
3
GPIO2
I
General purpose I/O bit 2. (Head Phone Plug)
4
GPIO3
O
General purpose I/O bit 3. (Amp Standby)
19
GPIO4
I/O
General purpose I/O bit 4.
20
GPIO5
O
General purpose I/O bit 5. (Antena_5V_SW)
21
GPIO6
I/O
General purpose I/O bit 6.
91
GPIO7
I/O
General purpose I/O bit 7.
92
GPIO8
I/O
General purpose I/O bit 8.
93
GPIO9
O
General purpose I/O bit 9. (Common Interface VCC Enable)
118
GPIO10
O
General purpose I/O bit 10. (Panel I2C Enable)
119
GPIO11
O
General purpose I/O bit 11. (Panel Write Protect)
120
GPIO12
I
General purpose I/O bit 12. (232C_Eable)
127
GPIO13
O
General purpose I/O bit 13. (ATV_Power_SW)
128
GPIO14
I
General purpose I/O bit 14. (Interrupt enable _SW)
PCMCIA/CI
83
D0
I/O
PCMCIA data bit 0.
85
D1
I/O
PCMCIA data bit 1.
87
D2
I/O
PCMCIA data bit 2.
24
D3
I/O
PCMCIA data bit 3.
26
D4
I/O
PCMCIA data bit 4.
28
D5
I/O
PCMCIA data bit 5.
30
D6
I/O
PCMCIA data bit 6.
32
D7
I/O
PCMCIA data bit 7.
81
D8
I/O
PCMCIA data bit 8.
84
D9
I/O
PCMCIA data bit 9.
86
D10
I/O
PCMCIA data bit 10.
25
D11
I/O
PCMCIA data bit 11.
27
D12
I/O
PCMCIA data bit 12.
29
D13
I/O
PCMCIA data bit 13.
31
D14
I/O
PCMCIA data bit 14.
34
D15
I/O
PCMCIA data bit 15.
80
A0
O
PCMCIA address bit 0.
78
A1
O
PCMCIA address bit 1.
75
A2
O
PCMCIA address bit 2.
73
A3
O
PCMCIA address bit 3.

6 20

TS_CPUOUT_CLK
TS_CPUOUT_SYNC
TS_CPUOUT_VAL
TS_CPUOUT_DO
open
open
open
open
open
open
open
TS_CPUIN_CLK
TS_CPUIN_SYNC
TS_CPUIN_VAL
TS_CPUIN_DO
R-G
R-G
HP_PLUG
AMP_STBY
open
ANT_5V_SW
open
open
open
CI_VCCEN
PNL_I2C_EN
PNL_WP
232C_EN
ATV_POW_SW
IREM_SW
C_D0
C_D1
C_D2
C_D3
C_D4
C_D5
C_D6
C_D7
TS_CIOUT_D0
TS_CIOUT_D1
TS_CIOUT_D2
TS_CIOUT_D3
TS_CIOUT_D4
TS_CIOUT_D5
TS_CIOUT_D6
TS_CIOUT_D7
CI_A0
CI_A1
CI_A2
CI_A3

LC-32/40/46LE600E/RU/S
Pin No.
Pin Name
I/O
Pin Function
71
A4
O
PCMCIA address bit 4.
69
A5
O
PCMCIA address bit 5.
66
A6
O
PCMCIA address bit 6.
64
A7
O
PCMCIA address bit 7.
46
A8
O
PCMCIA address bit 8.
44
A9
O
PCMCIA address bit 9.
37
A10
O
PCMCIA address bit 10.
41
A11
O
PCMCIA address bit 11.
62
A12
O
PCMCIA address bit 12.
48
A13
O
PCMCIA address bit 13.
50
A14
O
PCMCIA address bit 14.
59
A15
O
PCMCIA address bit 15.
57
A16
O
PCMCIA address bit 16.
45
A17
O
PCMCIA address bit 17.
47
A18
O
PCMCIA address bit 18.
49
A19
O
PCMCIA address bit 19.
51
A20
O
PCMCIA address bit 20.
54
A21
O
PCMCIA address bit 21.
56
A22
O
PCMCIA address bit 22.
58
A23
O
PCMCIA address bit 23.
61
A24
O
PCMCIA address bit 24.
63
A25
O
PCMCIA address bit 25.
67
RESET
O
PCMCIA reset.
35
CE1_
O
PCMCIA card enable 1.
36
CE2_
O
PCMCIA card enable 2.
23
CD1_
I
PCMCIA card detection 1.
88
CD2_
I
PCMCIA card detection 2.
38
VS1_
I
PCMCIA voltage sense 1.
65
VS2_
I
PCMCIA voltage sense 2.
79
BVD1
I
PCMCIA battery voltage detection 1.
77
BVD2
I
PCMCIA battery voltage detection 2.
72
INPACK_
I
PCMCIA input port acknowledge.
70
WAIT_
I
PCMCIA wait.
40
IORD_
O
PCMCIA IO read strobe.
42
IOWR_
O
PCMCIA IO write strobe.
74
REG_
O
PCMCIA register selection.
39
OE_
O
PCMCIA output enable.
53
WE_
O
PCMCIA write enable.
55
READY
I
PCMCIA ready.
89
WP
I
PCMCIA write protect.
General Purpose Input and Output (GPIO)
5
VCC33

I/O power 3.3V


33
VCC33

I/O power 3.3V


52
VCC33

I/O power 3.3V


68
VCC33

I/O power 3.3V


97
VCC33

I/O power 3.3V


121
VCC33

I/O power 3.3V


10
GND33

Ground
43
GND33

Ground
60
GND33

Ground
76
GND33

Ground
104
GND33

Ground
126
GND33

Ground
15
VCC18

Core power 1.8V


82
VCC18

Core power 1.8V


22
GND18

Ground
90
GND18

Ground
108
AVDD33_XTAL

Analog crystal power 3.3V


111
AVSS33_XTAL

Analog crystal ground


112
AVDD18_PLL

Analog PLL power 1.8V


113
AVSS18_PLL

Analog PLL ground

6 21

Sheet Name
CI_A4
CI_A5
CI_A6
CI_A7
CI_A8
CI_A9
CI_A10
CI_A11
CI_A12
CI_A13
CI_A14
TS_CIIN_CLK
TS_CIIN_VAL
TS_CIIN_SYNC
TS_CIIN_D0
TS_CIIN_D1
TS_CIIN_D2
TS_CIIN_D3
TS_CIIN_D4
TS_CIIN_D5
TS_CIIN_D6
TS_CIIN_D7
CI_RESET
CI_EN1
CI_EN2
CI_CARDDET1
CI_CARDDET2
C_VS1
TS_CIOUT_CLK
TS_CIOUT_SYNC
TS_CIOUT_VAL
CI_INP_ACK
CI_WAIT
CI_RD
CI_WR
CI_REG
CI_OE
CI_WE
CI_IREQ
CI_IOSIS16
D3.3V
D3.3V
D3.3V
D3.3V
D3.3V
D3.3V
G
G
G
G
G
G
D1.8V
D1.8V
G
G
D3.3V
G
D1.8V
G

LC-32/40/46LE600E/RU/S
2.16. IC2701 (VHiYDA148QZ-1Y)
This IC is a block diagram and description LC-32/40/46LE700E (S89B4LC32L700) please see the service manual.

2.17. IC9612 (VHiTCR5SB33-1Y)


2.17.1 Block Diagram

2.17.2 Pin Connections and short description


Pin No.
1
2
3
4
5

Pin Name
VIN
Ground
Control
NC
Vout

I/O
I
O

Pin Function
Voltage supply pin.
Ground pin
Control signal pin
No connection
Output pin

6 22

LC-32/40/46LE600E/RU/S
2.18. IC9605/IC9608 (VHiLV5893M+-1Y)
2.18.1 Block Diagram

2.18.2 Pin Connections and short description


Pin No.
1

Pin Name
BOOT

I/O
I

VIN

SW

4
5

GND
FB

COMP

EN

SS

Pin Function
Upper part MOS transistor boot strap capacity connection terminal.
Connect the boot capacity of about 0.022F between SW terminals.
The boot capacity series resistance (about100) is effective for stable operation.
Input power source terminal.
Connect very big capacity (10F 2 or more) between GND.
Power switch terminal.
Connect the output LC filter. Connect the above-mentioned capacity between BOOT terminals.
Ground
Feedback terminal.
The output voltage is set by the division resistance of output voltage (Vout-FB-GND).
Phase compensation terminal.
Connect external capacity and resistance for the phase compensation of the DC/DC converter close loop.
Enable terminal
It operates the converter by a high voltage or the opening. It stops with GND the converter operation.
Soft start terminal.
The soft start time is set by built-in 10A source voltage and external soft start capacity.

6 23

LC-32/40/46LE600E/RU/S
2.19. IC9611 (VHiTCR5SB25-1Y)
2.19.1 Pin Connections and short description
Pin No.
1
2
3

Pin Name
VIN

I/O
I

GND
CONTROL

Pin Function
Input power source terminal.
A small, ceramic type can be used for the input capacitor (0.1F).
Ground
Control terminal. In control voltage ON, it is 1.5-6V, and turning off is 0.25V or less.
Control voltage
HIGH
LOW

4
5

NC
VOUT

Output voltage
ON
OFF

No connection
Output voltage terminal.
The output voltage of TCR5SB25 is 2.5V0.05V.
A small, ceramic type can be used for the output capacitor (1.0F).

2.20. IC9604 (VHiLV58072M-1Y)


2.20.1 Block Diagram

2.20.2 Pin Connections and short description


Pin No.
1

Pin Name
BOOT

I/O
I

VIN

SW

4
5

GND
FB

COMP

EN

SS

Pin Function
Bootstrap Terminal
Connect the boost capacity of about 0.022F between SW terminals.
Input Voltage Terminal
Connect very big capacity between GND.
Power Switch Terminal
Connect output LC filter. Moreover connect the above-mentioned capacity between BOOT terminals.
Ground
Feed Back Terminal
The output voltage is set by the division resistance between the output voltages.
Phase Compensation Terminal
The phase amends external capacity and the resistance of the DC/DC converter close loop are connected.
Enable Terminal
The converter works by the High voltage impression.
Softstart Terminal
The soft start time is set by built-in 10A source voltage and external soft start capacity.

6 24

LC-32/40/46LE600E/RU/S
2.21. IC9606 (VHiLV5805M+-1Y)
This IC is a block diagram and description LC-19D1E (S58J9LC19D1ES) please see the service manual.

2.22. IC9603 (VHiMM3141YN-1Y)


2.22.1 Block Diagram

2.22.2 Pin Connections and short description


Pin No.
1
4
5
2

Pin Name
VDD
NC
Vout
NC
GND

I/O
O
-

CE

Pin Function
Voltage supply pin.
No connection
Output pin
No connection
Ground pin
ON/OFF control pin

Connect CE pin with VDD pin, when it is not used.

6 25

LC-32/40/46LE600E/RU/S
2.23. IC9610 (VHiPQ1LAX95-1Y)
2.23.1 Block Diagram

2.23.2 Pin Connections and short description


Pin No.
1
2
3
4
5

Pin Name
Vadj
GND
Vc
Vin
Vo

I/O
I
I
I
O

Pin Function
Output Voltage Control
Ground pin
ON/OFF Control
DC input
DC Output

6 26

LC-32/40/46LE600E/RU/S
2.24. IC2602, IC9601, IC9613 (VHiHC2G66DP-1Y)
2.24.1 Block Diagram

2.24.2 Pin Connections and short description


Pin No.
1
2
3
4
5
6
7
8

Pin Name
1Y
1Z
2E
GND
2Y
2Z
1E
VCC

I/O
I/O
I/O
I

I/O
I/O
I

Pin Function
Independent input or output.
Independent input or output.
Enable input (active HIGH).
Ground
Independent input or output.
Independent input or output.
Enable input (active HIGH).
Supply voltage.

6 27

LC-32/40/46LE600E/RU/S

Service
CHAPTER 5. TROUBLESHOOTING TABLE
LC32LE600E

Manual

[1] TROUBLESHOOTING TABLE


<POWER BLOCK: LC-32LE600E/RU/S>
No power supply (Front LED does not light up) and no power-up even if turned on (Front LED light up).

Is the wire harness in the unit properly connected?

NO

Reconnect and recheck the wire harness.

Are F7001 and F7002 normal?

NO

Are L7004, L7001,L7002,BD7001 etc. faulty?


Check if the peripheral circuits are short-circuited.

YES
Is BU+5V supplied from pin(11) of connector CN7003 (PD) when
the power switch is turned off?

NO

Check the peripheral circuits,


IC7101, T101, C7401, C7403, PC7008, etc .

YES
Is the PS_ON signal sent to pin(10) of connector CN7003 (PD)
when the power switch is turned on

NO

Check pin(AC11) of IC3303(VCT_P) on MAIN PWB.

YES
Is the AC_DET signal sent to pin(9) of connector CN7003 (PD)
when the power switch is turned on?

NO

Check the peripheral circuits,PC7007, Q7004, PC7002,etc.

YES
Is the DC voltage of approx. 400V supplied to both ends of
C7015?

NO

Does the PFC circuit normally work?


(Check IC7002, L7003, TH7001, IC7001, Q7005, Q7006etc. and
the peripheral circuits.)

YES
Is UR13V supplied from pins(1-4) of connector CN7003 (PD)
when the power switch is turned on?

NO

Check the peripheral circuits


(T7002, D7051, L7051, PC7001)

YES
Is PNL12V supplied from pins(1-2) of connector CN7004 (PL)
when the power switch is turned on?

NO

Check the peripheral circuits (U7053, etc )

NO

Check the peripheral circuits,


T7501, D7501, C7501, FA5511,etc .

YES

YES
Is 144V supplied from pins(2,4,6) of CN7007(LA2) and
pins(2,4,6,8,10,12) of CN7006 (LA1) when the power switch is
turned on?

51

LC-32/40/46LE600E/RU/S
<POWER BLOCK: LC-40/46LE600E/RU/S>
No power supply (Front LED does not light up) and no power-up even if turned on (Front LED light up).

Is the wire harness in the unit properly connected?

NO

Reconnect and recheck the wire harness.

NO

<40LE600E/RU/S>
Are L7001, L7002, L7003, D7101, D7103, VA7002, VA7001,
VA7003 etc... faulty?
Check if the peripheral circuits are short-circuited.
<46LE600E/RU/S>
Are L7001, L7002, L7003, L7004, D7101, VA7002, VA7001,
VA7003 etc... faulty?
Check if the peripheral circuits are short-circuited.

Is F7102 normal?

NO

Are TH7102, C7130, etc... faulty?

YES
Is BU+5V supplied from pin(11) of connector CN7501 (PD) when
the power switch is turned off?

NO

Check the peripheral circuits (IC7102, T7101, C7510, PC7102,


PC7101, etc )

YES
Is the PS_ON signal sent to pin(10) of connector CN7501 (PD)
when the power switch is turned on?

NO

Check pin(AC11) of IC3303(VCT_P) on MAIN PWB.

YES
Is the AC_DET signal sent to pin(9) of connector CN7501 (PD)
when the power switch is turned on?

NO

Check the peripheral circuits such as PS_ON circuits of Q7503,


PC7103, Q7118, Q7114 and PC7104, Q7501,Q7502, etc.

YES
Is the DC voltage of approx. 400V supplied to both ends of
C7144?

NO

<40LE600E/RU/S>
Does the PFC circuit normally work?
(Check IC7104, L7105, TH7101, RL7101, IC7200, Q7109,
Q7110 etc... and the peripheral circuits.)
<46LE600E/RU/S>
Does the PFC circuit normally work?
(Check IC7104, L7105, TH7101, RL7101, IC7101, Q7108,
Q7109 etc... and the peripheral circuits.)

NO

Check the peripheral circuits (T7102, D7507, C7514,7515,7516,


PC7105, PC7106, IC7503 etc...)

NO

Check the peripheral circuits (IC7502, etc )

NO

<40LE600E/RU/S>
Check the peripheral circuits, T7102, D7516, D7517, C7528,
L7501etc .
<46LE600E/RU/S>
Check the peripheral circuits, T7102, D7516, D7517, D7518,
C7528, C7538, L7501etc .

YES
Are F7001 and F7002 normal?

YES

YES
Is UR13V supplied from pins(1-4) of connector CN7501 (PD)
when the power switch is turned on?
YES
Is PNL12V supplied from pins(1-2) of connector CN7503 (PL)
when the power switch is turned on?
YES
<40LE600E/RU/S>
Is VLED supplied to pins(1-5) of CN7606(LA1) and pins(1-5) of
CN7607(LA2) when the power switch is turned on?
<46LE600E/RU/S>
Is VLED supplied to pins(1-5) of CN7606(LA1), pins(1-5) of
CN7607(LA2), pins(1-3) of CN7608(LA3) when the power switch
is turned on?

NO

52

LC-32/40/46LE600E/RU/S
<Backlight BLOCK: LC-32LE600E/RU/S>
The backlight does not light

Is either of fluorescence LEDs off?

YES

Check each fluorescent LED, and change defective parts.


(RUNTKA595WJ01, RUNTKA598WJ01,etc.)

Are all fluorescent LEDs on?

NO

Check each fluorescent LED, and change defective parts.


(RUNTKA595WJ01, RUNTKA598WJ01,etc.)

YES
Is REG3.3V supplied to pin(1) of CN7603(Driver_sub_PCB)
when the power switch is turned on?

NO

Check if the peripheral circuits are short-circuited or parts are


faulty. (U7701, U7702, etc )

NO

YES
Refer to "No power supply (Front LED does not light up)" and
"No power-up even if turned on (Front LED light up)"

YES
Is UR13V supplied from pins(1-4) of connector CN7003 (PD)
when the power switch is turned on?

NO

YES
Refer to "No power supply (Front LED does not light up)" and
"No power-up even if turned on (Front LED light up)"

YES
Is the STB_ON/OFF signal supplied from pin(8) of CN7008 (LB)?

YES
Is each control signal of CN7008(LB) normally function?
Pin(7) OFL (PWM light control signal input)
Pin(6) ERR (Error output)
YES
Is [LAMP_ERROR] indicated with [5] in a process mode?

YES
Is BL_ON output to pin(2) of CN7603 when the power switch is
turned on?
YES
Is 144V supplied to pins(2,4,6) of CN7007(LA2) and
pins(2,4,6,8,10,12) of CN7006(LA1) when the power switch is
turned on?

Check the peripheral circuits


(T7002, D7501, L7501, PC7001)

NO

Check the STB signal line on the MAIN_UNIT side (pin(2) of


P7602(LB), pin(D23) of IC3303(VCT_P), etc...)
and the peripheral circuits.

NO

Check each control circuit.

NO

[LAMP_ERROR] is returned to the default value in a process


mode.

NO

Check the peripheral circuits (IC7054, etc )

NO

Check if the peripheral circuits are short-circuited or parts are


faulty.
IC7251,PC7004, PC7006, T7501, D7501, C7501, FA5511,etc
YES
Refer to "No power supply (Front LED does not light up)" and
"No power-up even if turned on (Front LED light up)"

YES
Check if the peripheral circuits are short-circuited or parts are
faulty.
U7651, U7502, U7601-7605, Q7501-7509, Q7601-7609

53

LC-32/40/46LE600E/RU/S
<Backlight BLOCK: LC-40/46LE600E/RU/S>
The backlight does not light

Is either of fluorescence LEDs off?

YES

Check each fluorescent LED, and change defective parts.


(RUNTKA595WJ01, RUNTKA596WJ01, RUNTKA598WJ01
,etc.)

Are all fluorescent LEDs on?

NO

Check each fluorescent LED, and change defective parts.


(RUNTKA595WJ01, RUNTKA596WJ01, RUNTKA598WJ01
,etc.)

YES
Is 3.3V supplied to pins(1) of CN7603(Driver_sub_PCB) when
the power switch is turned off?

NO

Check if the peripheral circuits are short-circuited or parts are


faulty.(U7801, U7802, etc )

NO

YES
Refer to "No power supply (Front LED does not light up)" and
"No power-up even if turned on (Front LED light up)"

YES
Is UR13V supplied from pins(1) of connector
CN7604(Driver_sub_PCB) when the power switch is turned on?

NO

YES
Refer to "No power supply (Front LED does not light up)" and
"No power-up even if turned on (Front LED light up)"

YES
Is the STB_ON/OFF signal supplied from pin(8) of CN7605 (LB)?

YES
Is each control signal of CN7605 (LB) normally function?
Pin(7) OFL (PWM light control signal input)
Pin(6) ERR (Error output)
YES
Is [LAMP_ERROR] indicated with [5] in a process mode?

YES
Is BL_ON output to pin(2) of CN7603(Driver_sub_PCB) when
the power switch is turned on?
YES
<40LE600E/RU/S>
Is VLED(187V) supplied to pins(1-5) of CN7606(LA1) and pins(15) of CN7007(LA2) when the power switch is turned on?
<46LE600E/RU/S>
Is VLED(209V) supplied to pins(1-5) of CN7606(LA1), pins(1-5)
of CN7007(LA2), pins(1-3) of CN7608(LA3) when the power
switch is turned on?

Check if the peripheral circuits are short-circuited or parts are


faulty.
(T7102, D7507, C7514,7515,7516, PC7105, PC7106,
IC7505etc )

NO

Check the STB signal line on the MAIN_UNIT side (pin(2) of


P9602(LB), pin(D23) of IC3303(VCT_P), etc...)
and the peripheral circuits.

NO

Check each control circuit.

NO

[LAMP_ERROR] is returned to the default value in a process


mode.

NO

Check the peripheral circuits (IC7054, etc )

NO

<40LE600E/RU/S>
Check if the peripheral circuits are short-circuited or parts are
faulty.
T7102, D7516, D7517, C7528, L7501, D7525etc
<46LE600E/RU/S>
Check if the peripheral circuits are short-circuited or parts are
faulty.
T7103, D7516, D7517, D7518, C7528, C7538, L7501, C7525,
C7526 etc

NO

YES
Refer to "No power supply (Front LED does not light up)" and
"No power-up even if turned on (Front LED light up)"

YES
Check if the peripheral circuits are short-circuited or parts are
faulty.
IC7508, IC7601-7607, Q7601-7613, etc

54

LC-32/40/46LE600E/RU/S
No sound (1-1) (during the reception of TV broadcasting)

No audio output during UHF/


VHF reception

Checklist:
1) Is the volume set to MIN or MUTE on the remote control? Set the desired volume.
2) Is ANT-CABLE disconnected or connected improperly? Connect it correctly as per the operation manual.
3) Attention: The terminal of IC3303 (VCT) cannot be actually checked by hiding oneself, and check it with another terminal of the same line,
please.
(MAIN-UNIT)
Is the audio signal
(AOUT_SP_L/R) output from
pins (H26) and (H25) of
IC3303 (VCT)?
(MAIN-UNIT)

(TUNER SIDE)
Is the audio signal (SIF)
input to pin (AB25) of
IC3303 (VCT)?

NO

YES

Check whether there are a


power supply of IC3303
(VCT), the short circuit,
and other abnormalities.

YES

Check whether there are


open-circuit or short-circuit between tuner
(TU1102) and IC3303.

NO

Check whether there are


open-circuit or short-circuit between tuner
(TU1102) and Q1105 (5VREG) or between tuner
and IC1101.

NO

Pursue an I2C line and


look for the part of an
open circuit or the short
circuit.

NO

Check whether there is an


open circuit or the short
circuit in an IF_AGC signal line.

YES

Is the audio signal


(SPKOUT_L/R) output form
pins (17) and (18) of
IC1302 (A-SW) normally?

YES
Is the audio signal (LCH/
RCH) output form pins
(31)/(27) and (11)/(14) of
IC2701 (A-AMP) normally?

YES
Is the audio output signal
outputted to pins (1)-(4) of
SP-Connector (P2701) normally?
YES
Is the SP-Wire harness
connected and operated
orthopedically normally?

YES
Check right and left SPBOX, and exchange defective SP-BOX
(R: RSP-ZA392WJZZ/
L: RSP-ZA391WJZZ)

NO

Check S9V power supply


(10) (15) pin, D3.3V
power supply (3) (36)
pin, and AUSW-MUTE
signal (29) pin of IC1302
(A-SW) or the peripheral
circuits.

NO

Check AMP12.5V power


supply (1) (10) pin, AMPSTBY input signal (17)
pin, and audio-mute signal pin (19) of IC2701 (AAMP) or the peripheral
circuits.

NO

Check SP- Connector


(P2701) and peripheral
circuits.

NO

Correct an abnormal part


of SP- harness.

NO
Is the SIF signal output
from pin (4) of tuner
(TU1102)?

NO
Check whether IF5V
power supply is supplied to pin (3) of tuner
(TU1102), and ANT5V
power supply is supplied to pin (1) of tuner
(TU1102)?
YES
Check whether the I2C
signal (SDA/SCL) is
functioning by (9) (8)
pin of tuner (TU1102).
YES
Check whether IF_AGC
is functioning between
pin (E24) of IC3303 and
pin (15) of tuner
(TU1102)
YES
Replace tuner
(TU1102).

A-BLOCK

55

LC-32/40/46LE600E/RU/S
No sound (1-2) (during the reception of DTV broadcasting)

No audio output during DTV


reception

Checklist:
1) Is the volume set to MIN or MUTE on the remote control? Set the desired volume.
2) Is ANT-CABLE disconnected or connected improperly? Connect it correctly as per the operation manual.
3) Attention: The terminal of IC3303 (VCT) cannot be actually checked by hiding oneself, and check it with another terminal of the same line,
please.
(MAIN-UNIT)
Is the audio signal
(AOUT_SP_L/R) output
from pins (H26) and (H25) of
IC3303 (VCT)?

(MAIN-UNIT)

YES

(TUNER SIDE)
Is the digital IF signal
(D_IF) input to pins
(T25) (R25) of IC3303
(VCT)?

NO

YES

Check whether there


are a power supply of
IC3303 (VCT), the short
circuit, and other abnormalities.

YES

Check whether there


are open-circuit or
short-circuit between
tuner (TU1102) and
IC3303.

NO

Check whether there


are open-circuit or
short-circuit between
Q1105 (5V-REG) and
tuner (TU1102).

NO

Pursue an I2C line and


look for the part of an
open circuit or the short
circuit.

NO

Check whether there is


an open circuit or the
short circuit in an
IF_AGC signal line.

(OUTPUT_SIDE)
NO

Is the audio signal


(SPKOUT_L/R) output
form pins (17) and (18) of
IC1302 (A-SW) normally?

YES
Is the audio signal (LCH/
RCH) output form pins
(31) (27) and (11) (14) of
IC2701 (A-AMP) properly?

YES
Is the audio output signal
outputted to pins (1)-(4) of
SP-Connector (P2701)
normally?
YES
Is the SP-Wire harness
(SP) connected and operated orthopedically normally?

YES
Check right and left SPBOX, and exchange
defective SP-BOX
(R: RSP-ZA392WJZZ/
L: RSP-ZA391WJZZ)

NO

Check S9V power supply


(10) (15) pin, D3.3V power
supply (3) (36) pin, and
AUSW-mute signal (29)
pin of IC1302 (A-SW) or
the peripheral circuits.

NO

Check AMP12.5V power


supply (1) (10) pin, AMPSTBY input signal (17) pin,
and audio-mute signal pin
(19) of IC2701 (A-AMP) or
the peripheral circuits.

NO

Check SP-Connector
(P2701) and peripheral circuits.

NO

Correct an abnormal part


of SP- harness.

Is the digital IF signal


(D_IF) output from pins
(17) (16) of tuner
(TU1102)?

NO
Check whether the IF5V
power supply is supplied to pin (3) of tuner
(TU1102).

YES
Check whether the I2C
signal (SDA/SCL) is
functioning by pin (9) (8)
of tuner (TU1102).
YES
Check whether IF_AGC
is functioning between
pin (E24) of IC3303 and
pin (15) of tuner
(TU1102)
YES
Replace tuner
(TU1102).

A-BLOCK

56

LC-32/40/46LE600E/RU/S
No sound from external input devices (2-1)-1

No sound from EXT1 (SCART1) connecting an external input


device.

<EXT1>
Is the SC1_IN_L (SCART1-L-IN) audio signal input from pin (6)
of SCART1 terminal (SC503) to pin (44) of IC1302 (A-SW)?
Is the SC1_IN_R (SCART1-R-IN) audio signal input from pin (2)
of SCART1 terminal (SC503) to pin (43) of IC1302 (A-SW)?

NO

Check pins (6) (2) of SCART1 and connection of an external


input device.

YES
Is the audio signal (A_IN_L/R) properly output from pins (6) and
(7) of IC1302 (A-SW)?

NO

Check S9V power supply (10) (15) pin, D3.3V power supply (3)
(36) pin, and SDA0/SCL0 signal (28) (27) pin of IC1302 (A-SW)
or the peripheral circuit.

YES
Is the audio signal (A_OUT_SP_L/R) properly output from pins
(H26) and (H25) of IC3303 (VCT)?

NO

Check D3.3V power supply pin (F18) of IC3303 (VCT) and the
soldering confirmation or the peripheral circuit.

YES
It is the same as the above-mentioned A-BLOCK.
No sound from external input devices (2-1)-2

No sound from EXT2 (SCART2) connecting an external input


device.

<EXT2>
Is the SC2_IN_L (SCART2-L-IN) audio signal input from pin (6)
of SCART2 terminal (SC502) to pin (46) of IC1302 (A-SW)?
Is the SC2_IN_R (SCART2-R-IN) audio signal input from pin (2)
of SCART2 terminal (SC502) to pin (45) of IC1302 (A-SW)?

NO

Check pins (6) (2) of SCART2 and connection of an external


input device.

YES
Is the audio signal (A_IN_L/R) properly output from pins (6) and
(7) of IC1302 (A-SW)?

NO

Check S9V power supply (10) (15) pin, D3.3V power supply (3)
(36) pin, and SDA0/SCL0 signal (28) (27) pin of IC1302 (A-SW)
or the peripheral circuit.

YES
Is the audio signal (A_OUT_SP_L/R) properly output from pins
(H26) and (H24) of IC3303 (VCT)?

NO

Check D3.3V power supply pin (F18) of IC3303 (VCT) and the
soldering confirmation or the peripheral circuit.

YES
It is the same as the above-mentioned A-BLOCK.

57

LC-32/40/46LE600E/RU/S
No sound from external input devices (2-2)-1

No sound from EXT3 (COMP-A-IN) connecting an external input


device.

<EXT3>
Is COMP_IN_L audio signal input to pin (2) of EXT3_AUDIO
(J502)?
Is COMP_IN_R audio signal input to pin (4) of EXT3_AUDIO
(J502)?
YES
Is COMP_IN_L audio signal input to pin (48) of IC1302 (A-SW)?
Is COMP_IN_R audio signal input to pin (47) of IC1302 (A-SW)?
YES
Is the audio signal (A_IN_L/R) properly output from pins (6) and
(7) of IC1302 (A-SW)?

NO

Check S9V power supply (10) (15) pin, D3.3V power supply (3)
(36) pin, and SDA0/SCL0 signal pin (28) (27) of IC1302 (A-SW)
or the peripheral circuit.

YES
Is the audio signal (A_OUT_SP_L/R) properly output from pins
(H26) and (H25) of IC3303 (VCT)?

NO

Check D3.3V power supply pin (F18) of IC3303 (VCT) and the
soldering confirmation or the peripheral circuit.

YES
It is the same as the above-mentioned A-BLOCK.
No sound from external input devices (2-2) -2

No sound from EXT4 (PC/HDMI-A-IN) connecting an external


input device.

<EXT4>
Is PC/HDMI-L audio signal input to pin (2) of EXT4 (J501)?
Is PC/HDMI-R audio signal input to pin (3) of EXT4 (J501)?
YES
Is PC/HDMI-L audio signal input to pin (50) of IC1302 (A-SW)?
Is PC/HDMI-R audio signal input to pin (49) of IC1302 (A-SW)?
YES
Is the audio signal (A_IN_L/R) properly output from pins (6) and
(7) of IC1302 (A-SW)?

NO

Check S9V power supply (10) (15) pin, D3.3V power supply (3)
(36) pin, and SDA0/SCL0 signal pin (28) (27) of IC1302 (A-SW)
or the peripheral circuit.

YES
Is the audio signal (A_OUT_SP_L/R) properly output from pins
(H26) and (H25) of IC3303 (VCT)?

NO

Check D3.3V power supply pin (F18) of IC3303 (VCT) and the
soldering confirmation or the peripheral circuit.

YES
It is the same as the above-mentioned A-BLOCK.

58

LC-32/40/46LE600E/RU/S
No sound from external input devices (2-2)-3

No sound from EXT8 (CVBS-A-IN) connecting an external input


device.

<EXT8>
Is CVBS-L audio signal input to pin (5) of EXT8 (J505)?
Is CVBS-R audio signal input to pin (4) of EXT8 (J505)?
YES
Is CVBS-L audio signal input to pin (52) of IC1302 (A-SW)?
Is CVBS-R audio signal input to pin (51) of IC1302 (A-SW)?
YES
Is the audio signal (A_IN_L/R) properly output from pins (6) and
(7) of IC1302 (A-SW)?

NO

Check S9V power supply (10) (15) pin, D3.3V power supply (3)
(36) pin, and SDA0/SCL0 signal pin (28) (27) of IC1302 (A-SW)
or the peripheral circuit.

YES
Is the audio signal (A_OUT_SP_L/R) properly output from pins
(H26) and (H25) of IC3303 (VCT)?

NO

Check D3.3V power supply pin (F18) of IC3303 (VCT) and the
soldering confirmation or the peripheral circuit.

YES
It is the same as the above-mentioned A-BLOCK.
No sound of external device (3-1)-1

No audio output from EXT1 (SCART1) terminal.

Checklist:
1) Is the MUTE button on the remote control set to ON? Set to OFF.
2) Check the connection to external devices. Is there any improper connection?

Is audio signal output to pins (3) and (1) of EXT1 (SCART1)


(SC503)?

YES

Check EXT1 (SCART1) (SC503) and the connection to an external device.

YES

The Q502 base should usually be L.


If it is H signal, Check whether base of Q1301 is L or peripheral circuit.

NO
Is the audio output signal (TUNER_OUT_L/R) output from pins
(11) and (10) of IC1301 (DAC) normal?

YES

Check whether there are problems in IC1301 and Q502 or


peripheral circuits.

NO
Is the audio output signal (I2S_DATA_TU) output from pins (B25)
of IC3303 (VCT) normal?

YES

Check whether there is problem in IC3303.

NO
The input source of the audio is decided from TUNER. Is the SIF
signal input to pin (AB25) of IC3303 (VCT)?

YES

Check whether there are problems in the power supply and soldering IC3303 or peripheral circuits.

NO
Is the SC1-MUTE signal of base (5) (2) pin of Q502 H?

NO
TUNER: TU1102
Check Q1101 (AMP), and pin (4) of TUNER.

59

LC-32/40/46LE600E/RU/S
No sound of external device (3-1)-2

No audio output from EXT2 (SCART2) terminal.

Checklist:
1) Is the MUTE button on the remote control set to ON? Set to OFF.
2) Check the connection to external devices. Is there any improper connection?

Is audio signal output to pins (3) and (1) of EXT2 (SCART2)


(SC502)?
NO
Is the SC2-MUTE signal of base (5) (2) pin of Q501 H?

YES
Is the audio output signal (MONITOR_OUT_L/R) output from
pins (19) and (20) of IC1302 (A-SW) normally?
NO
Isn't there problem in the power supply input (S9V, D3.3V) of
IC1302 (A-SW), I2C_0 signal (SDA0/SCL0), and defective soldering, etc.?

YES

Check EXT2 (SCART2) (SC502) and the connection to an external device.

NO

The Q501 base should usually be L.


If it is H signal, Check whether base of Q1301 is L or peripheral circuit.

YES

Check whether there are problems in IC1302, Q503, Q504 and


Q501 or peripheral circuits.

NO

Repair the faulty point around IC1302.

YES
Where is the input source of the sound from?
(EXT1, EXT2, EXT3, EXT4, EXT8)

Check whether there is any problem in each input (terminal).

EXT1/2: SCART1/2
Check pin (44) (43)/(46) (45) of IC1302 and pin (6) (2) of EXT1/2
terminal (SCART1/2).
EXT3: COMP
Check pin (48) (47) of IC1302, and pin (2) (4) of EXT3 terminal
(J502).
EXT4: PC/HDMI
Check pin (50) (49) of IC1302, and pin (2) (3) of EXT4 terminal
(J501).
EXT8: CVBS
Check pin (52) (51) of IC1302, and pin (5) (4) of EXT8 terminal
(J505).

5 10

LC-32/40/46LE600E/RU/S
No sound of external device (3-2)

No sound from AUDIO OUT (J506). (MONITOR OUT)

Is the audio output signal send to pins (2) and (4) of the AUDIO
OUT terminal (J506)?

YES

Check AUDIO OUT terminal (J506) and the connection to an


external device.

NO
Is the AUDIO-MUTE L signal input to pins (5) and (2) of Q509
base?

NO

The Q1301 base should usually be H. If it is L signal, Check


pin (35) of IC1302, pin (1) of IC1303, and soldering.

YES
Is the audio output signal (MONITOR_OUT_L/R) output from
pins (19) and (20) of IC1302 (A-SW) normally?

YES

Check the power supply input (S9V, D3.3V), soldering, and the
peripheral circuit of IC1302 (A-SW).

NO

Repair the faulty point around IC1302.

NO
Isn't there problem in the power supply input (S9V, D3.3V) of
IC1302 (A-SW), I2C_0 signal (SDA0/SCL0), and defective soldering, etc.?
YES
Where is the input source of the sound from?
(TUNER, EXT1, EXT1, EXT3, EXT4, EXT8)

Check whether there is any problem in each input (terminal).

TU1102: TUNER
Check pin (AB25) of IC3303, and pin (4) of TUNER.
EXT1/2: SCART1/2
Check pin (44) (43)/(46) (45) of IC1302 and pin (6) (2) of EXT1/2
terminal (SCART1/2).
EXT3: COMP_L/R
Check pin (48) (47) of IC1302, and pin (2) (4) of EXT3 terminal
(J502).
EXT4: PC/HDMI_L/R
Check pin (50) (49) of IC1302, and pin (2) (4) of EXT4 terminal
(J501)
EXT8: CVBS_L/R
Check pin (52) (51) of IC1302, and pin (5) (4) of EXT8 terminal
(J505).

5 11

L C - 3 2 / 4 0 /4 6 L E 6 0 0 E / R U / S
No sound of external device (3-3)

No DIGITAL sound from OPT OUT (D520).

Is the DIGITAL audio signal output to pin (1) of the OPT OUT terminal (D520)?

YES

Check OPT OUT terminal (D520) and the connection to an external device.

NO
Is the DIGITAL audio signal (OPT_ OUT) output from pin (4) of
IC503?

YES

Check whether it is normal between an OPT OUT terminal


(D520) and IC503.

NO
Isn't the AUDIO_MUTE signal inputted into pin (1) of IC503 by
L?

YES

The pin (1) of IC503 should usually be H. If it is L signal,


check Q505, pin (1) of Q1301 and pin (35) of IC1302.

NO
Is the DIGITAL audio signal (OPT_ OUT) output from pin (E26) of
IC3303 (VCT) normally?

YES

Check whether it is normal between IC503 and IC3303.

NO

Repair the faulty point around IC3303.

NO
Isn't there problem in the power supply input (D3.3V, D1.1V) of
IC3303 (VCT), I2C_0 signal (SDA0/SCL0), and defective soldering, etc.?
YES
Where is the input source of the sound from?
(TUNER, EXT5, EXT6, EXT7)

Check whether there is any problem in each input (terminal).

TU1102: TUNER
Check pin (T25) (R25) of IC3303, and pin (16) (17) of TUNER.
EXT5: HDMI_1
Check the TMDS input signal of HDMI_1 (1) (9) pin, the TMDS I/
O signal of IC1508, and the TMDS input signal of IC3303.
EXT6: HDMI_2
Check the TMDS input signal of HDMI_2 (1) (9) pin, the TMDS I/
O signal of IC1508, and the TMDS input signal of IC3303.
EXT7: HDMI_3
Check the TMDS input signal of HDMI_3 (1) (9) pin, the TMDS I/
O signal of IC1508, and the TMDS input signal of IC3303.

5 12

LC-32/40/46LE600E/RU/S
<When tuner (U/V, DTV) is received>

No picture on the display (1)-1

No picture appears on LCD during the tuner (U/V) reception.

Checklist:
1) Is INPUT SOURCE button
on the remote control set up correctly? set it as TV with the INPUT SOURCE button
on the remote
control.
2) Is MENU-Picture-Backlight/Contrast/Brightness set to MIN? Set it to an appropriate level.
3) Is ANT-CABLE disconnected or connected improperly? Connect it correctly as per the operation manual.
4) Attention: The terminal of IC3303 (VCT) cannot be actually checked by hiding oneself, and check it with another terminal of the same line,
please.
YES
Is the level of pins (9) and (8) of tuner (TU1102) at H?

NO

These are communications lines for control (I2C). Follow the


path and check whether they are forced to L (PULL_DOWN).
(IC3303 (F25) (F24) pin)

YES
Is the video signal (VIDEO) output from pin (6) of tuner
(TU1102)?

NO

Check the tuner (TU1102) and peripheral circuits.

YES
Is the video signal (TUNER_CVBS) input to pin (AD25) of lC3303
(VCT)?

NO

Isn't there any part with short-circuits at IC3303 (VCT)? or Check


peripheral circuits.

YES
Is the LVDS video signal (LVDS0_D [0:4] ) output from pin
[A6:A11], [B6:B11] of lC3303 (VCT)?

NO

Check IC3303 (VCT), and peripheral circuits.

NO

Check whether there is short circuit between [A6:A11], [B6:B11]


pin of IC3303 (VCT) and (40)-(28) pin of LW Connector (P2601),
and peripheral circuits.

YES
Is the I2C signal (VCOM_SDA/SCL) send to pin(12)/(13) of LP
Connector (P2602)?

NO

Check the I2C signal of IC2602 and peripheral circuit.

YES
Is the PNL12V output to pin (1)/(2) of PL Connector (CN7004(32
inch)/CN7503(40/46 inch)) of POWER UNIT?

NO

Check PL connector of POWER UNIT and U7053(32inch)/


IC7502(40/46inch).

YES
Is the LVDS video signal (LVDS0_D [0:4] ) input to pins (40)(28) of LW Connector (P2601), and is CLK signal (TCLK) input
to pins (32)/(33)?

YES
Exchange LCD-CONT-UNIT and do it operate normally?
NO
Check the contact of the LCD-CONT-UNIT connection harness
(LW/LP/PL).
Exchange LCD-PANEL if it is useless even if it exchanges it.

5 13

LC-32/40/46LE600E/RU/S
<When tuner (U/V, DTV) is received>

No picture on the display (1)-2

No picture appears on LCD during the tuner (DTV) reception.

Checklist:
1) Is INPUT SOURCE button
on the remote control set up correctly? set it as TV with the INPUT SOURCE button
on the remote
control.
2) Is MENU-Picture-Backlight/Contrast/Brightness set to MIN? Set it to an appropriate level.
3) Is ANT-CABLE disconnected or connected improperly? Connect it correctly as per the operation manual.
4) Attention: The terminal of IC3303 (VCT) cannot be actually checked by hiding oneself, and check it with another terminal of the same line,
please.
YES
Is the level of pins (9) and (8) of tuner (TU1102) at H?

NO

These are communications lines for control (I2C). Follow the


path and check whether they are forced to L(PULL_DOWN).
(IC3303 (F25) (F24) pin)

YES
Is the digital video signal (DIFP/N) output from pin (16) (17) of
tuner (TU1102)?

NO

Check the tuner (TU1102) and peripheral circuits.

YES
Is the digital video signal (DIFP/N) input to pin (T25) (R25) of
lC3303 (VCT)?

NO

Isn't there any part with short-circuits at IC3303 (VCT)? or Check


peripheral circuits.

YES
Is the LVDS video signal (LVDS0_D [0:4] ) output from pin
[A6:A11], [B6:B11] of lC3303 (VCT)?

NO

Check IC3303 (VCT), and peripheral circuits.

NO

Check whether there is short circuit between [A6:A11], [B6:B11]


pin of IC3303 (VCT) and (40)-(28) pin of LW Connector (P2601),
and peripheral circuits.

YES
Is the I2C signal (VCOM_SDA/SCL) send to pin(12)/(13) of LP
Connector (P2602)?

NO

Check the I2C signal of IC2602 and peripheral circuit.

YES
Is the PNL12V output to pin (1)/(2) of PL Connector (CN7004(32
inch)/CN7503(40/46 inch)) of POWER UNIT?

NO

Check PL connector of POWER UNIT and U7053(32inch)/


IC7502(40/46inch).

YES
Is the LVDS video signal (LVDS0_D [0:4] ) input to pins (40)(28) of LW Connector (P2601), and is CLK signal (TCLK) input
to pins (32)/(33)?

YES
Exchange LCD-CONT-UNIT and do it operate normally?
NO
Check the contact of the LCD-CONT-UNIT connection harness
(LW/LP/PL).
Exchange LCD-PANEL if it is useless even if it exchanges it.

5 14

LC-32/40/46LE600E/RU/S
<When EXT1 is used for external input>

No picture on the display (2)-1

No Composite video output when the EXT1 external input is


used.

Checklist:
1) Is INPUT SOURCE button
on the remote control set up correctly? set it as EXT1 with the INPUT SOURCE button on the remote
control.
2) Is MENU-Picture-Backlight/Contrast/Brightness set to MIN? Set it to an appropriate level.
3) Check the connection to the external device Connect it correctly as per the operation manual for the device.
4) Attention: The terminal of IC3303 (VCT) cannot be actually checked by hiding oneself, and check it with another terminal of the same line,
please.

Is the CVBS video signal (SC1_CVBS/Y) sent to pin (20) of


SCART1 (SC503)?

NO

Check external connection, input setting, SCART1 (SC503) and


peripheral circuits.

NO

IC3303 (VCT), I2C_0signal (SDA0/SCL0), and peripheral circuits.

NO

Check whether there is short circuit between [A6:A11], [B6:B11]


pin of IC3303 (VCT) and (40)-(28) pin of LW Connector (P2601),
and peripheral circuits.

YES
Is the I2C signal (VCOM_SDA/SCL) send to pin(12)/(13) of LP
Connector (P2602)?

NO

Check the I2C signal of IC2602 and peripheral circuit.

YES
Is the PNL12V output to pin (1)/(2) of PL Connector (CN7004(32
inch)/CN7503(40/46 inch)) of POWER UNIT?

NO

Check PL connector of POWER UNIT and U7053(32inch)/


IC7502(40/46inch).

YES
Is the CVBS video signal (SC1_CVBS/Y) sent to input terminal
pin (AE24) of IC3303 (VCT)?
YES
Is the LVDS video signal (LVDS0_D [0:4]) input to pins (40)-(28)
of LW Connector (P2601), and is CLK signal (TCLK) input to
pins (32)/(33)?

YES
Exchange LCD-CONT-UNIT and do it operate normally?
NO
Check the contact of the LCD-CONT-UNIT connection harness
(LW/LP/PL).
Exchange LCD-PANEL if it is useless even if it exchanges it.

5 15

LC-32/40/46LE600E/RU/S
<When EXT1 is used for external input>

No picture on the display (2)-2

No RGB output when the EXT1 external input is used.

Checklist:
1) Is INPUT SOURCE button
on the remote control set up correctly? set it as EXT1 with the INPUT SOURCE button on the remote
control.
2) Is MENU-Picture-Backlight/Contrast/Brightness set to MIN? Set it to an appropriate level.
3) Check the connection to the external device Connect it correctly as per the operation manual for the device.
4) Attention: The terminal of IC3303 (VCT) cannot be actually checked by hiding oneself, and check it with another terminal of the same line,
please.

Is the RGB signal sent to pins (15), (11) and (7) of SCART1
(SC503)? (RED1, GREEN1, BLUE1)

NO

Check external connection, input setting, SCART1 (SC503) and


peripheral circuits.

Is the RGB signal (RED1, GREEN1, BLUE1) sent to input terminal pins (AF24), (AD24) and (AD23) of IC3303 (VCT)?

NO

Check between pins (15) (11) (7) of SCART1 (SC503) and pins
(AF24) (AD24) (AD23) of IC3303 (VCT) and peripheral circuits.

NO

Check whether there is short circuit between [A6:A11], [B6:B11]


pin of IC3303 (VCT) and (40)-(28) pin of LW Connector (P2601),
and peripheral circuits.

YES
Is the I2C signal (VCOM_SDA/SCL) send to pin(12)/(13) of LP
Connector (P2602)?

NO

Check the I2C signal of IC2602 and peripheral circuit.

YES
Is the PNL12V output to pin (1)/(2) of PL Connector (CN7004(32
inch)/CN7503(40/46 inch)) of POWER UNIT?

NO

Check PL connector of POWER UNIT and U7053(32inch)/


IC7502(40/46inch).

YES
Is the LVDS video signal (LVDS0_D [0:4] ) input to pins (40)(28) of LW Connector (P2601), and is CLK signal (TCLK) input
to pins (32)/(33)?

YES
Exchange LCD-CONT-UNIT and do it operate normally?
NO
Check the contact of the LCD-CONT-UNIT connection harness
(LW/LP/PL).
Exchange LCD-PANEL if it is useless even if it exchanges it.

5 16

LC-32/40/46LE600E/RU/S
<When EXT1 is used for external input>

No picture on the display (2)-3

No Y/C output when the EXT1 external input is used.

Checklist:
1) Is INPUT SOURCE button
on the remote control set up correctly? set it as EXT1 with the INPUT SOURCE button on the remote
control.
2) Is MENU-Picture-Backlight/Contrast/Brightness set to MIN? Set it to an appropriate level.
3) Check the connection to the external device Connect it correctly as per the operation manual for the device.
4) Attention: The terminal of IC3303 (VCT) cannot be actually checked by hiding oneself, and check it with another terminal of the same line,
please.

Is the Y/C signal sent to pins (20) and (15) of SCART1 (SC503)?
(Y/C1)

NO

Check external connection, input setting, SCART1 (SC503) and


peripheral circuits.

NO

Check between pins (20) (15) of SCART1 (SC503) and pins


(AE24) (AF24) of IC3303 (VCT), and peripheral circuits.

NO

Check whether there is short circuit between [A6:A11], [B6:B11]


pin of IC3303 (VCT) and (40)-(28) pin of LW Connector (P2601),
and peripheral circuits.

YES
Is the I2C signal (VCOM_SDA/SCL) send to pin(12)/(13) of LP
Connector (P2602)?

NO

Check the I2C signal of IC2602 and peripheral circuit.

YES
Is the PNL12V output to pin (1)/(2) of PL Connector (CN7004(32
inch)/CN7503(40/46 inch)) of POWER UNIT?

NO

Check PL connector of POWER UNIT and U7053(32inch)/


IC7502(40/46inch).

YES
Is the Y/C signal (Y/C1) sent to input terminal pins (AE24) and
(AF24) of IC3303 (VCT)?
YES
Is the LVDS video signal (LVDS0_D [0:4] ) input to pins (40)(28) of LW Connector (P2601), and is CLK signal (TCLK) input
to pins (32)/(33)?

YES
Exchange LCD-CONT-UNIT and do it operate normally?
NO
Check the contact of the LCD-CONT-UNIT connection harness
(LW/LP/PL).
Exchange LCD-PANEL if it is useless even if it exchanges it.

5 17

LC-32/40/46LE600E/RU/S
<When EXT2 is used for external input>

No picture on the display (3)-1

No composite video output when the EXT2 external input is


used.

Checklist:
1) Is INPUT SOURCE button
on the remote control set up correctly? set it as EXT2 with the INPUT SOURCE button on the remote control.
2) Is MENU-Picture-Backlight/Contrast/Brightness set to MIN? Set it to an appropriate level.
3) Check the connection to the external device Connect it correctly as per the operation manual for the device.
4) Attention: The terminal of IC3303 (VCT) cannot be actually checked by hiding oneself, and check it with another terminal of the same line,
please.

Is the CVBS video signal sent to pin (20) of SCART2 (SC502)?

NO

Check external connection, input setting, SCART2 (SC502) and


peripheral circuits.

YES
Is the CVBS video signal (SC2_CVBS/Y) sent to input terminal
pin (AD26) of IC3303 (VCT)?

NO

Check IC3303 (VCT), I2C_0 signal (SDA0/SCL0), and peripheral


circuits.

NO

Check whether there is short circuit between [A6:A11], [B6:B11]


pin of IC3303 (VCT) and (40)-(28) pin of LW Connector (P2601),
and peripheral circuits.

YES
Is the I2C signal (VCOM_SDA/SCL) send to pin(12)/(13) of LP
Connector (P2602)?

NO

Check the I2C signal of IC2602 and peripheral circuit.

YES
Is the PNL12V output to pin (1)/(2) of PL Connector (CN7004(32
inch)/CN7503(40/46 inch)) of POWER UNIT?

NO

Check PL connector of POWER UNIT and U7053(32inch)/


IC7502(40/46inch).

YES
Is the LVDS video signal (LVDS0_D [0:4] ) input to pins (40)(28) of LW Connector (P2601), and is CLK signal (TCLK) input
to pins (32)/(33)?

YES
Exchange LCD-CONT-UNIT and do it operate normally?
NO
Check the contact of the LCD-CONT-UNIT connection harness
(LW/LP/PL).
Exchange LCD-PANEL if it is useless even if it exchanges it.

5 18

LC-32/40/46LE600E/RU/S
<When EXT2 is used for external input>

No picture on the display (3)-2

No Y/C output when the EXT2 external input is used.

Checklist:
1) Is INPUT SOURCE button
on the remote control set up correctly? set it as EXT2 with the INPUT SOURCE button on the remote control.
2) Is MENU-Picture-Backlight/Contrast/Brightness set to MIN? Set it to an appropriate level.
3) Check the connection to the external device Connect it correctly as per the operation manual for the device.
4) Attention: The terminal of IC3303 (VCT) cannot be actually checked by hiding oneself, and check it with another terminal of the same line,
please.

Is the Y/C signal sent to pins (20) and (15) of SCART2 (SC502)?
(SC2_Y/C2)

NO

Check external connection, input setting, SCART2 (SC502) and


peripheral circuits.

NO

Check between pins (20) (15) of SCART2 (SC502) and pins


(AD26) (AF25) of IC3303 (VCT) and peripheral circuits.

NO

Check whether there is short circuit between [A6:A11], [B6:B11]


pin of IC3303 (VCT) and (40)-(28) pin of LW Connector (P2601),
and peripheral circuits.

YES
Is the I2C signal (VCOM_SDA/SCL) send to pin(12)/(13) of LP
Connector (P2602)?

NO

Check the I2C signal of IC2602 and peripheral circuit.

YES
Is the PNL12V output to pin (1)/(2) of PL Connector (CN7004(32
inch)/CN7503(40/46 inch)) of POWER UNIT?

NO

Check PL connector of POWER UNIT and U7053(32inch)/


IC7502(40/46inch).

YES
Is the Y/C signal (SC2_Y/C2) sent to input terminal pins (AD26)
and (AF25) of IC3303 (VCT)?
YES
Is the LVDS video signal (LVDS0_D [0:4] ) input to pins (40)(28) of LW Connector (P2601), and is CLK signal (TCLK) input
to pins (32)/(33)?

YES
Exchange LCD-CONT-UNIT and do it operate normally?
NO
Check the contact of the LCD-CONT-UNIT connection harness
(LW/LP/PL).
Exchange LCD-PANEL if it is useless even if it exchanges it.

5 19

LC-32/40/46LE600E/RU/S
<When EXT3/4/8 is used for external input>

No picture on the display (4)-1

No Component video output when the EXT3 external input is


used.

Checklist:
1) Is INPUT SOURCE button
on the remote control set up correctly? set it as EXT3/EXT4/EXT8 with the INPUT SOURCE button on
the remote control.
2) Is MENU-Picture-Backlight/Contrast/Brightness set to MIN? Set it to an appropriate level.
3) Check the connection to the external device Connect it correctly as per the operation manual for the device.
4) Attention: The terminal of IC3303 (VCT) cannot be actually checked by hiding oneself, and check it with another terminal of the same line,
please.

Is the component video signal sent to pin (3) (5) (7) of EXT3 terminal (J503)? (Y, Pb, Pr)

NO

Check external connection, input setting, EXT3 terminal (J503)


and peripheral circuits.

NO

Check between pins (3) (5) (7) of EXT3 terminal (J503) and pins
(AE21) (AD22) (AF22) of IC3303 (VCT) and peripheral circuits.

NO

Check whether there is short circuit between [A6:A11], [B6:B11]


pin of IC3303 (VCT) and (40)-(28) pin of LW Connector (P2601),
and peripheral circuits.

YES
Is the I2C signal (VCOM_SDA/SCL) send to pin(12)/(13) of LP
Connector (P2602)?

NO

Check the I2C signal of IC2602 and peripheral circuit.

YES
Is the PNL12V output to pin (1)/(2) of PL Connector (CN7004(32
inch)/CN7503(40/46 inch)) of POWER UNIT?

NO

Check PL connector of POWER UNIT and U7053(32inch)/


IC7502(40/46inch).

YES
Is the component video signal (COMP_Y/Pb/Pr) sent to input terminal pin (AE21) (AD22) (AF22) of IC3303 (VCT)?
YES
Is the LVDS video signal (LVDS0_D [0:4] ) input to pins (40)(28) of LW Connector (P2601), and is CLK signal (TCLK) input
to pins (32)/(33)?

YES
Exchange LCD-CONT-UNIT and do it operate normally?
NO
Check the contact of the LCD-CONT-UNIT connection harness
(LW/LP/PL).
Exchange LCD-PANEL if it is useless even if it exchanges it.

5 20

LC-32/40/46LE600E/RU/S
<When EXT3/4/8 is used for external input>

No picture on the display (4)-2

No PC output when the EXT4 external input is used.

Checklist:
1) Is INPUT SOURCE button
on the remote control set up correctly? set it as EXT3/EXT4/EXT8 with the INPUT SOURCE button on
the remote control.
2) Is MENU-Picture-Backlight/Contrast/Brightness set to MIN? Set it to an appropriate level.
3) Check the connection to the external device Connect it correctly as per the operation manual for the device.
4) Attention: The terminal of IC3303 (VCT) cannot be actually checked by hiding oneself, and check it with another terminal of the same line,
please.

Is the RGB signal sent to pins (1), (2) and (3) of EXT4 terminal
(PC_IN) (SC501)? (PC_R/G/B)

NO

Check external connection, input setting, EXT4 terminal (PC_IN)


(SC501) and peripheral circuits.

NO

Check between pins (1) (2) (3) of EXT4 terminal (PC_IN)


(SC501) and pins (AE20) (AE19) (AD19) of IC3303 (VCT).

NO

Check whether there is short circuit between [A6:A11], [B6:B11]


pin of IC3303 (VCT) and (40)-(28) pin of LW Connector (P2601),
and peripheral circuits.

YES
Is the I2C signal (VCOM_SDA/SCL) send to pin(12)/(13) of LP
Connector (P2602)?

NO

Check the I2C signal of IC2602 and peripheral circuit.

YES
Is the PNL12V output to pin (1)/(2) of PL Connector (CN7004(32
inch)/CN7503(40/46 inch)) of POWER UNIT?

NO

Check PL connector of POWER UNIT and U7053(32inch)/


IC7502(40/46inch).

YES
Is the RGB signal (PC_R/G/B) sent to input terminal pins (AE20)
(AE19) and (AD19) of IC3303 (VCT)?
YES
Is the LVDS video signal (LVDS0_D [0:4] ) input to pins (40)(28) of LW Connector (P2601), and is CLK signal (TCLK) input
to pins (32)/(33)?

YES
Exchange LCD-CONT-UNIT and do it operate normally?
NO
Check the contact of the LCD-CONT-UNIT connection harness
(LW/LP/PL).
Exchange LCD-PANEL if it is useless even if it exchanges it.

5 21

LC-32/40/46LE600E/RU/S
<When EXT3/4/8 is used for external input>

No picture on the display (4)-3

No Composite video output when the EXT8 external input is


used.

Checklist:
1) Is INPUT SOURCE button
on the remote control set up correctly? set it as EXT3/EXT4/EXT8 with the INPUT SOURCE button on
the remote control.
2) Is MENU-Picture-Backlight/Contrast/Brightness set to MIN? Set it to an appropriate level.
3) Check the connection to the external device Connect it correctly as per the operation manual for the device.
4) Attention: The terminal of IC3303 (VCT) cannot be actually checked by hiding oneself, and check it with another terminal of the same line,
please.

Is the Composite video signal sent to pin (6) of EXT8 terminal


(J505)? (CVBS_IN)

NO

Check external connection, input setting, EXT8 terminal (J505)


and peripheral circuits.

NO

Check between pin (6) of EXT8 terminal (J505) and pin (AC24)
of IC3303 (VCT) and peripheral circuits.

NO

Check whether there is short circuit between [A6:A11], [B6:B11]


pin of IC3303 (VCT) and (40)-(28) pin of LW Connector (P2601),
and peripheral circuits.

YES
Is the I2C signal (VCOM_SDA/SCL) send to pin(12)/(13) of LP
Connector (P2602)?

NO

Check the I2C signal of IC2602 and peripheral circuit.

YES
Is the PNL12V output to pin (1)/(2) of PL Connector (CN7004(32
inch)/CN7503(40/46 inch)) of POWER UNIT?

NO

Check PL connector of POWER UNIT and U7053(32inch)/


IC7502(40/46inch).

YES
Is the Composite video signal (CVBS_IN) sent to input terminal
pin (AC24) of IC3303 (VCT)?
YES
Is the LVDS video signal (LVDS0_D [0:4] ) input to pins (40)(28) of LW Connector (P2601), and is CLK signal (TCLK) input
to pins (32)/(33)?

YES
Exchange LCD-CONT-UNIT and do it operate normally?
NO
Check the contact of the LCD-CONT-UNIT connection harness
(LW/LP/PL).
Exchange LCD-PANEL if it is useless even if it exchanges it.

5 22

LC-32/40/46LE600E/RU/S
<When EXT5/6/7(HDMI) is used for external input>

No picture on the display (5)-1

No HDMI0 digital video output when the EXT5 external input is


used.

Checklist:
1) Is INPUT SOURCE button
on the remote control set up correctly? set it as EXT5/EXT6/EXT7 with the INPUT SOURCE button on
the remote control.
2) Is MENU-Picture-Backlight/Contrast/Brightness set to MIN? Set it to an appropriate level.
3) Check the connection to the external device Connect it correctly as per the operation manual for the device.
4) Attention: The terminal of IC3303 (VCT) cannot be actually checked by hiding oneself, and check it with another terminal of the same line,
please.

Is the HDMI Digital video signal sent to pin (1)-(9) of EXT5 terminal (SC1501)? (HDMI0_D [0:2] _P/N)

NO

Check external connection, input setting, EXT5 terminal


(SC1501) and peripheral circuits.

NO

Check short circuit of EXT5 terminal (SC1501), and peripheral


circuits.

NO

Check short circuit of IC1508 (HDMI_receiver), power source


and peripheral circuits.

NO

Check whether there is short circuit between [A6:A11], [B6:B11]


pin of IC3303 (VCT) and (40)-(28) pin of LW Connector (P2601),
and peripheral circuits.

YES
Is the I2C signal (VCOM_SDA/SCL) send to pin(12)/(13) of LP
Connector (P2602)?

NO

Check the I2C signal of IC2602 and peripheral circuit.

YES
Is the PNL12V output to pin (1)/(2) of PL Connector (CN7004(32
inch)/CN7503(40/46 inch)) of POWER UNIT?

NO

Check PL connector of POWER UNIT and U7053(32inch)/


IC7502(40/46inch).

YES
Is the HDMI Digital video signal sent to pin (21)-(26) of IC1508
(HDMI-receiver)? (HDMI0_D [0:2] _P/N)
YES
Is HDMI_SW_ Digital Video signal sent to pin (AF16) (AE16)(AF18) (AE18) of input terminal of IC3303 (VCT)?
(HDMI_SW_D [0:2] P/N)
YES
Is the LVDS video signal (LVDS0_D [0:4] ) input to pins (40)(28) of LW Connector (P2601), and is CLK signal (TCLK) input
to pins (32)/(33)?

YES
Exchange LCD-CONT-UNIT and do it operate normally?
NO
Check the contact of the LCD-CONT-UNIT connection harness
(LW/LP/PL).
Exchange LCD-PANEL if it is useless even if it exchanges it.

5 23

LC-32/40/46LE600E/RU/S
<When EXT5/6/7(HDMI) is used for external input>

No picture on the display (5)-2

No HDMI1 digital video output when the EXT6 external input is


used.

Checklist:
1) Is INPUT SOURCE button
on the remote control set up correctly? set it as EXT5/EXT6/EXT7 with the INPUT SOURCE button on
the remote control.
2) Is MENU-Picture-Backlight/Contrast/Brightness set to MIN? Set it to an appropriate level.
3) Check the connection to the external device Connect it correctly as per the operation manual for the device.
4) Attention: The terminal of IC3303 (VCT) cannot be actually checked by hiding oneself, and check it with another terminal of the same line,
please.

Is the HDMI Digital video signal sent to pin (1)-(9) of EXT6 terminal (SC1502)? (HDMI1_D [0:2] _P/N)

NO

Check external connection, input setting, EXT6 terminal


(SC1502) and peripheral circuits.

NO

Check short circuit of EXT6 terminal (SC1502), and peripheral


circuits.

NO

Check short circuit of IC1508 (HDMI_receiver), power source


and peripheral circuits.

NO

Check whether there is short circuit between [A6:A11], [B6:B11]


pin of IC3303 (VCT) and (40)-(28) pin of LW Connector (P2601),
and peripheral circuits.

YES
Is the I2C signal (VCOM_SDA/SCL) send to pin(12)/(13) of LP
Connector (P2602)?

NO

Check the I2C signal of IC2602 and peripheral circuit.

YES
Is the PNL12V output to pin (1)/(2) of PL Connector (CN7004(32
inch)/CN7503(40/46 inch)) of POWER UNIT?

NO

Check PL connector of POWER UNIT and U7053(32inch)/


IC7502(40/46inch).

YES
Is the HDMI Digital video signal sent to pin (13)-(18) of IC1508
(HDMI-receiver)? (HDMI1_D [0:2] _P/N)
YES
Is HDMI_SW_ Digital Video signal sent to pin (AF16) (AE16)(AF18) (AE18) of input terminal of IC3303 (VCT)?
(HDMI_SW_D [0:2] P/N)
YES
Is the LVDS video signal (LVDS0_D [0:4] ) input to pins (40)(28) of LW Connector (P2601), and is CLK signal (TCLK) input
to pins (32)/(33)?

YES
Exchange LCD-CONT-UNIT and do it operate normally?
NO
Check the contact of the LCD-CONT-UNIT connection harness
(LW/LP/PL).
Exchange LCD-PANEL if it is useless even if it exchanges it.

5 24

LC-32/40/46LE600E/RU/S
<When EXT5/6/7 (HDMI) is used for external input>

No picture on the display (5)-3

No HDMI2 digital video output when the EXT7 external input is


used.

Checklist:
1) Is INPUT SOURCE button
on the remote control set up correctly? set it as EXT5/EXT6/EXT7 with the INPUT SOURCE button on
the remote control.
2) Is MENU-Picture-Backlight/Contrast/Brightness set to MIN? Set it to an appropriate level.
3) Check the connection to the external device Connect it correctly as per the operation manual for the device.
4) Attention: The terminal of IC3303 (VCT) cannot be actually checked by hiding oneself, and check it with another terminal of the same line,
please.

Is the HDMI Digital video signal sent to pin (1)-(9) of EXT7 terminal (SC1503)? (HDMI2_D [0:2] _P/N)

NO

Check external connection, input setting, EXT7 terminal


(SC1503) and peripheral circuits.

NO

Check short circuit of EXT7 terminal (SC1503), and peripheral


circuits.

NO

Check short circuit of IC1508 (HDMI_receiver), power source


and peripheral circuits.

NO

Check whether there is short circuit between [A6:A11], [B6:B11]


pin of IC3303 (VCT) and (40)-(28) pin of LW Connector (P2601),
and peripheral circuits.

YES
Is the I2C signal (VCOM_SDA/SCL) send to pin(12)/(13) of LP
Connector (P2602)?

NO

Check the I2C signal of IC2602 and peripheral circuit.

YES
Is the PNL12V output to pin (1)/(2) of PL Connector (CN7004(32
inch)/CN7503(40/46 inch)) of POWER UNIT?

NO

Check PL connector of POWER UNIT and U7053(32inch)/


IC7502(40/46inch).

YES
Is the HDMI Digital video signal sent to pin (3)-(8) of IC1508
(HDMI-receiver)? (HDMI2_D [0:2] _P/N)
YES
Is HDMI_SW_ Digital Video signal sent to pin (AF16) (AE16)(AF18) (AE18) of input terminal of IC3303 (VCT)?
(HDMI_SW_D [0:2] P/N)
YES
Is the LVDS video signal (LVDS0_D [0:4] ) input to pins (40)(28) of LW Connector (P2601), and is CLK signal (TCLK) input
to pins (32)/(33)?

YES
Exchange LCD-CONT-UNIT and do it operate normally?
NO
Check the contact of the LCD-CONT-UNIT connection harness
(LW/LP/PL).
Exchange LCD-PANEL if it is useless even if it exchanges it.

5 25

LC-32/40/46LE600E/RU/S
<When an external monitor is connected>

No picture on the external monitor (6)-1

No picture appears on external monitor during the tuner (U/V)


reception. (Tuner input, EXT1 output)

Checklist:
1) Are input terminal on back of TV and INPUT SOURCE button
on the remote control set up correctly? See the operation manual and
set INPUT SOURCE appropriately. set to EXT***.
2) Is SCART-CABLE disconnected or connected improperly? Connect it correctly as per the operation manual.

Is the video signal outputted to pin (19) of SCART1 (SC503)?

YES

Check SCART1, external connection or input setting.

NO
Is the video signal (SC1-VOUT) outputted from pin (2) of IC504
(75_driver)?

YES

Check SCART1 (SC503) and peripheral circuits.

YES

Check IC507 and peripheral circuits.

YES

Check IC3303 and peripheral circuits.

NO
Is video signal (CVBS_TU_OUT) input to pin (4) of IC507?

NO
Is video signal (TUNER_CVBS) outputted from emitter of
Q1102?
NO
Is video signal (VIDEO) outputted from pin (6) of TUNER
(TU1102)?
NO
Check IF5V power supply pins (3), 12C-line pins (9) and (8) of
tuner (TU1102) and peripheral circuits.

5 26

LC-32/40/46LE600E/RU/S
<When an external monitor is connected>

No picture on the external monitor (6)-2

No picture appears on external monitor during the EXT8 input


(COMPOSITE).
(EXT8 COMP input, EXT2 output)

Checklist:
1) Are input terminal on back of TV and INPUT SOURCE button
on the remote control set up correctly? See the operation manual and
set INPUT SOURCE appropriately. set to EXT***.
2) Is SCART-CABLE disconnected or connected improperly? Connect it correctly as per the operation manual.

Is the video signal outputted to pin (19) of SCART2 (SC502)?

YES

Check SCART2, external connection or input setting.

NO
Is the video signal (SC2-VOUT) outputted from pin (4) of IC508
(75_driver)?

YES

Check IC508 and peripheral circuits.

NO
Is the Composite Video signal (CVBS_MON_OUT) outputted
from the pin (B13) of IC3303 (VCT)?

YES

Check between IC508 and IC3303 and the peripheral circuitry.

NO
Is the Composite signal (CVBS_IN) inputted to pins (6) of EXT8
terminal normally?

YES

Check a short circuit etc. between the EXT8 input terminal (pin
(6)) and IC3303 (VCT).

NO
Check whether the terminal of EXT8 is faulty, or there is not any
error in external connection.

5 27

LC-32/40/46LE600E/RU/S
<When an external monitor is connected>

No picture on the external monitor (6)-3

No picture appears on external monitor during the EXT5/6/7


inputs (HDMI). (EXT5 HDMI input, EXT2 output)

Checklist:
1) Are input terminal on back of TV and INPUT SOURCE button
on the remote control set up correctly? See the operation manual and
set INPUT SOURCE appropriately. set to EXT***.
2) Is SCART-CABLE disconnected or connected improperly? Connect it correctly as per the operation manual.

Is the video signal outputted to pin (19) of SCART2 (SC502)?

YES

Check SCART2, external connection or input setting.

NO
Is the video signal (SC2-VOUT) outputted from pin (4) of IC508
(75_driver)?

YES

Check IC508 and peripheral circuits.

NO
Is the Composite Video signal (CVBS_MON_OUT) outputted
from the pin (B13) of IC3303 (VCT)?

YES

Check between IC508 and IC3303 and the peripheral circuitry.

NO
Is the HDMI output signal (HDMI_SW_D [0:2] P/N) input to the
pin [AF16-AE18] of IC3303 (VCT) normally?

YES

Check a short circuit, HDMI_H/V signal, HDMI_PLG signal, and


other abnormality, etc. with IC3303.

NO
Is the HDMI input signal (HDMI0/1/2_D [0:2] P/N) input to IC1508
(HDMI-receiver) normally?

YES

Check a short circuit, HDMI_I2C signal, and other abnormality,


etc. with IC1508.

NO
Are the pin (43) (44)/(39) (40)/(33) (34) of I2C signal (HDMI [0:2]
_SDA/SCL) accessed normally?

NO

Exchange HDMI-Receiver (IC1508) Or check short circuit.

YES
Is the TMDS signal (1-12) pin inputted to HDMI1/2/3 (EXT5/6/7)
terminal normally?

YES

Check a short circuit etc. between HDMI1/2/3 and IC1508


(HDMI-receiver).

NO
Check whether the terminal of HDMI1/2/3 (EXT5/6/7) is faulty, or
there is not any error in external connection.

5 28

LC-32/40/46LE600E/RU/S
LCD failure (1)

Does a single or several


vertical stripes appear
on the LCD screen?

Does a single or several


horizontal stripes appear
on the LCD screen?

Do luminescent or black
dots appear on the
screen?

Is the on-screen image


rippling or distorted?

Is there any portion


which some screens
were darkish or
became whitish?

Are the data bit dropout?


(No solution even when
turning on and off the QS
drive)

Is the gamma correction as specified?

Replace the LCD panel.


LCD failure (2)

The backlight functions. Does not the


image come out in the
LCD screen
(screen black)?

Does the entire LCD


screen look whitish all
over?

Does the QS drive function?

Replace the LCD_CONT_UNIT.

5 29

LCD 2010 06 01
Date of Issue:
Classification:

LCD TELEVISION TECHNICAL BULLETIN

MODELS

LC32LE600E

LC40LE600E

25th June 2010


White
Page 1 of 1

LC46LE600E

SYMPTOM Squealing or no sound.


CAUSE

Software issues in main sound processing IC.

ACTION

Update software to the latest version following the instructions in the service manual,
Following this update please perform a factory reset.
Note that the latest version of software is available from the Sharp Tech Web.

Sharp Electronics (UK) Limited


Reference LCEU96
Revision - 2

White Carry out as required


Yellow Carry out as required and whenever the unit comes in for service
Red Carry out on all units

LCD 2010 06 07
Date of Issue:
Classification:

LCD TELEVISION TECHNICAL BULLETIN

MODELS

LC32LE600E

LC40LE600E

25th June 2010


White
Page 1 of 3

LC46LE600E

SYMPTOM Stuck in stand by following software update or PWB replacement the Red LED
flashing, if there has been more than 5 attempts to bring the TV on with the incorrect
settings then the TV will be none responsive and show only the Red power LED.
CAUSE

Incorrect MODEL NAME / INCH SIZE identification within the service menu setup
software resulting in Lamp error protection mode STANDBY CAUSE (1B).

ACTION

Follow the instructions given below to gain access to the engineer service menu and
check/reset INCH SIZE and MODEL NAME where applicable.
Switch the TV off using the rocker switch located on the lower left side of the TV (just
around the back).
Whilst hold down the Input button and Volume buttons on the set, switch the TV on
again using the rocker switch left side.
After 30 seconds the set should function showing a [K] in the upper left part of the
screen.
Press together the Volume and Program buttons on the set.
You should now be in the engineer service menu (see Figure 1).
Using the Channel up and Down buttons on the remote to select the INCH SIZE then
MODEL NAME and correct using the Right arrow or Volume + - button to the details as
indicated on the cabinet back (see Figures 2 and 3).
Reset STANBY CAUSE as required, change ERROR RESET to YES and press
OK.

Do not make any other adjustments within any other part of the service menus
as this can result in unrecoverable errors.
When completed switch off and remove the mains supply.

Sharp Electronics (UK) Limited


Reference JW20100526
Revision - 1

White Carry out as required


Yellow Carry out as required and whenever the unit comes in for service
Red Carry out on all units

LCD 2010 06 07
Date of Issue:
Classification:

LCD TELEVISION TECHNICAL BULLETIN

25th June 2010


White
Page 2 of 3

Figure 1: Service menu showing screen size and Model name.

Figure 2: Service menu indications of Model versions selection E, E(A), E(B) or E(C).

Sharp Electronics (UK) Limited


Reference JW20100526
Revision - 1

White Carry out as required


Yellow Carry out as required and whenever the unit comes in for service
Red Carry out on all units

LCD 2010 06 07
Date of Issue:
Classification:

LCD TELEVISION TECHNICAL BULLETIN

25th June 2010


White
Page 3 of 3

Figure 3: The Model number may be followed by a box containing the Variant letter, the above
label shows the [A] variant which must be set in the service mode detailed above along with the
46 in the INCH SIZE..

Sharp Electronics (UK) Limited


Reference JW20100526
Revision - 1

White Carry out as required


Yellow Carry out as required and whenever the unit comes in for service
Red Carry out on all units

LCD 2010 05 05
Date of Issue:
Classification:

LCD TELEVISION TECHNICAL BULLETIN

MODELS

LC32LE600E

LC40LE600E

15th May 2010


White
Page 1 of 2

LC46LE600E

SYMPTOM Stuck in shut-down following software update or PWB replacement.


CAUSE

Incorrect model/size identification within the service menu setup software.

ACTION

Follow the instructions given below to gain access to the engineer service menu and
check/reset screen size and model version.

Whilst hold down the Input source and Volume buttons on the set, insert the
mains cable or turn on the mains supply.
After 30 seconds release these buttons.
The set should now start to function.
Press together the Volume and Program buttons on the set.
You should now be in the engineer service menu (see Figure 1).
Using the curser buttons on the remote highlight and reset if needed the model
size and Model name-version ( A,B,C. ) as indicated on the cabinet back (see
Figures 2 and 3).
Do not make any other adjustments within any other part of the service
menus as this can result in unrecoverable errors.
When completed switch off and remove the mains supply.

Figure 1: Service menu showing screen size and Model name.

Sharp Electronics (UK) Limited


Reference JW20100326
Revision - 1

White Carry out as required


Yellow Carry out as required and whenever the unit comes in for service
Red Carry out on all units

LCD 2010 05 05
Date of Issue:
Classification:

LCD TELEVISION TECHNICAL BULLETIN

15th May 2010


White
Page 2 of 2

Figure 2: Service menu indications of Model versions E,E(A),E(B) or E(C).

Figure 3: The Model number may be followed by a box containing Variant letter as indicated
above ( A ).

Sharp Electronics (UK) Limited


Reference JW20100326
Revision - 1

White Carry out as required


Yellow Carry out as required and whenever the unit comes in for service
Red Carry out on all units

LCD 2009 12 07
Date of Issue:
Classification:

LCD TELEVISION TECHNICAL BULLETIN

MODELS

LC32LE600E

LC40LE600E

LC40LE600EA

5th December 2009


White
Page 1 of 4

LC46LE600E

LC46LE600EA
REASON

Incorrect part number for IC501 quoted on various pages of the service manual.

ACTION

If you need to replace IC501 please use the correct part number and add the updated
information on the following pages to the service manual.

REF NO

DESCRIPTION

PART NUMBER

IC501

1K E2PROM

RH-iXXC206WJZZS

Sharp Electronics (UK) Limited


Reference EEL998
Revision - 1

White Carry out as required


Yellow Carry out as required and whenever the unit comes in for service
Red Carry out on all units

PRICE CODE
AH

LCD 2009 12 07
Date of Issue:
Classification:

LCD TELEVISION TECHNICAL BULLETIN

5th December 2009


White
Page 2 of 4

Figure 1: Chapter 4 Adjustment Procedure - Page 1

Sharp Electronics (UK) Limited


Reference EEL998
Revision - 1

White Carry out as required


Yellow Carry out as required and whenever the unit comes in for service
Red Carry out on all units

LCD 2009 12 07
Date of Issue:
Classification:

LCD TELEVISION TECHNICAL BULLETIN

5th December 2009


White
Page 3 of 4

Figure 2: Chapter 6 Major IC Information - Page 1.

Sharp Electronics (UK) Limited


Reference EEL998
Revision - 1

White Carry out as required


Yellow Carry out as required and whenever the unit comes in for service
Red Carry out on all units

LCD 2009 12 07
Date of Issue:
Classification:

LCD TELEVISION TECHNICAL BULLETIN

5th December 2009


White
Page 4 of 4

Figure 3: Parts List - Page 8.

Sharp Electronics (UK) Limited


Reference EEL998
Revision - 1

White Carry out as required


Yellow Carry out as required and whenever the unit comes in for service
Red Carry out on all units

LCD 2009 12 02
Date of Issue:
Classification:

LCD TELEVISION TECHNICAL BULLETIN

MODELS

LC32LE600E

LC40LE600E

LC46LE600E

5th December 2009


White
Page 1 of 1

LC52LE600E

REASON

Changes in LCD panel assembly and Main PWB during production.

ACTION

When servicing please check the rear rating plate to ensure the correct circuit and
parts list is being used as there are currently 3 versions including A an B variants.

Figure 1: Original Version Model Number only. Figure 2: Indication of A Version chassis.

Sharp Electronics (UK) Limited


Reference LV315
Revision - 1

White Carry out as required


Yellow Carry out as required and whenever the unit comes in for service
Red Carry out on all units

You might also like