Professional Documents
Culture Documents
1. Scope *
1.1 This specification covers hot-finished or cold-finished
bars except bars for reforging (Note 1). It includes rounds,
squares, and hexagons, and hot-rolled or extruded shapes, such
as angles, tees, and channels in the more commonly used types
of stainless steels. The free-machining types (Note 2), for
general corrosion resistance and high-temperature service, are
covered in a separate specification.
3. Ordering Information
3.1 It is the responsibility of the purchaser to specify all
requirements that are necessary for material ordered under this
specification. Such requirements may include but are not
limited to the following:
3.1.1 Quantity (weight or number of pieces),
3.1.2 Name of material: stainless steel,
3.1.3 Form (bars, angles, etc.),
3.1.4 Condition (Section 4.1),
3.1.5 Finish (Section 8 of Specification A 484/A 484M),
3.1.6 Surface preparation of shapes (Section 8 of Specification A 484/A 484M),
3.1.7 Applicable dimensions including size, thickness,
width, and length,
3.1.8 Cross section (round, square, etc.),
3.1.9 Type or UNS designation (Table 1),
3.1.10 ASTM designation and date of issue, and
3.1.11 Whether bars are to be rolled as bars or cut from strip
or plate.
3.1.12 Test for magnetic permeability when specified by
customer purchase order when ordering Types 201 and 205.
3.1.13 Special requirements.
4. Manufacture
4.1 Condition:
4.1.1 Bars shall be furnished in one of the following
conditions listed in the Mechanical Requirements table:
4.1.1.1 Condition AAnnealed
4.1.1.2 Condition HHardened and tempered at a relatively low temperature
4.1.1.3 Condition THardened and tempered at a relatively
high temperature
4.1.1.4 Condition SStrain HardenedRelatively light
cold work
4.1.1.5 Condition BRelatively severe cold work
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
Stainless Steel, and Related Alloys and is the direct responsibility of Subcommittee
A01.17 on Flat Stainless Steel Products.
Current edition approved September 10, 2002. Published October 2002. Originally published as A 276 44 T. Last previous edition A 276 02.
2
Annual Book of ASTM Standards, Vol 01.03.
3
Annual Book of ASTM Standards, Vol 01.01.
4
Available from Society of Automotive Engineers, 400 Commonwealth Drive,
Warrendale, PA 15096.
5. Chemical Composition
5.1 The steel shall conform to the requirements for chemical
NOTICE: This standard has either been superceded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
A 276 02a
composition specified in Table 1.
5.2 Methods and practices relating to chemical analysis
required by this specification shall be in accordance with Test
Methods, Practices, and Terminology A 751.
8. General Requirements
8.1 In addition to the requirements of this specification, all
requirements of the current edition of Specification A 484/
A 484M shall apply. Failure to comply with the general
requirements of Specification A 484/A 484M constitutes nonconformance to this specification.
9. Certification
9.1 Upon request of the purchaser in the contract or order,
the producers certification that the material was manufactured
and tested in accordance with this specification, together with
a certified report of the test results shall be furnished at the time
of the shipment.
10. Keywords
7. Magnetic Permeability
7.1 When required by the purchase order, the magnetic
permeability of Types 201 and 205 in the annealed condition
shall not exceed 1.2 as tested by a Severn-type indicator.
SUMMARY OF CHANGES
This section contains principal changes that have been incorporated since the 02 edition.
(1) Carbon minimum added for UNS designation S41000 in
Table 1.
TABLE 1 Chemical RequirementsA
Composition, %
UNS
DesignationB
Type
N08367
S20100
S20161
S20162
S20200
S20500
S20910
S21800
S21900
S21904
S24000
S24100
S28200
S30200
S30215
S30400
S30403
S30451
S30452
S30453
S30454
S30500
S30800
S30815
S30900
S30908
S30940
S31000
S31008
S31040
S31254
Carbon
Manganese
Phosphorus
...
201
...
...
202
205
XM-19
0.030
0.15
0.15
0.15
0.15
0.120.25
0.06
2.00
5.57.5
4.06.0
4.08.0
7.510.0
14.015.5
4.06.0
0.040
0.060
0.045
0.040
0.060
0.060
0.045
0.030
0.030
0.030
0.040
0.030
0.030
0.030
1.00
1.00
3.04.0
2.54.5
1.00
1.00
1.00
20.022.0
16.018.0
15.018.0
16.521.0
17.019.0
16.518.0
20.523.5
23.525.5
3.55.5
4.06.0
6.010.0
4.06.0
1.01.7
11.513.5
6.07.0
...
...
0.502.50
...
...
1.503.00
0.180.25
0.25
0.080.20
0.050.25
0.25
0.320.40
0.200.40
...
XM-10
XM-11
XM-29
XM-28
...
302
302B
304
304LC
304N
XM-21
304LN
...
305
308
...
309
309S
309Cb
310
310S
310Cb
...
0.10
0.08
0.04
0.08
0.15
0.15
0.15
0.15
0.08
0.030
0.08
0.08
0.030
0.03
0.12
0.08
0.050.10
0.20
0.08
0.08
0.25
0.08
0.08
0.020
7.09.0
8.010.0
8.010.0
11.514.5
11.014.0
17.019.0
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
0.80
2.00
2.00
2.00
2.00
2.00
2.00
1.00
0.060
0.045
0.045
0.060
0.045
0.045
0.045
0.045
0.045
0.045
0.045
0.045
0.045
0.045
0.045
0.045
0.040
0.045
0.045
0.045
0.045
0.045
0.045
0.030
0.030
0.030
0.030
0.030
0.030
0.030
0.030
0.030
0.030
0.030
0.030
0.030
0.030
0.030
0.030
0.030
0.030
0.030
0.030
0.030
0.030
0.030
0.030
0.010
3.54.5
1.00
1.00
1.00
1.00
1.00
1.00
2.003.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.402.00
1.00
1.00
1.00
1.50
1.50
1.50
0.80
16.018.0
19.021.5
19.021.5
17.019.0
16.519.0
17.019.0
17.019.0
17.019.0
18.020.0
18.020.0
18.020.0
18.020.0
18.020.0
18.020.0
17.019.0
19.021.0
20.022.0
22.024.0
22.024.0
22.024.0
24.026.0
24.026.0
24.026.0
19.520.5
8.09.0
5.57.5
5.57.5
2.33.7
0.502.50
...
8.010.0
8.010.0
8.011.0
8.012.0
8.011.0
8.010.0
8.011.0
8.011.0
11.013.0
10.012.0
10.012.0
12.015.0
12.015.0
12.016.0
19.022.0
19.022.0
19.022.0
17.518.5
...
...
...
...
...
0.751.25
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
6.06.5
0.080.18
0.150.40
0.150.40
0.200.40
0.200.45
0.400.60
0.10
0.10
...
...
0.100.16
0.160.30
0.100.16
0.160.30
...
...
0.140.20
...
...
...
...
...
...
0.180.22
Sulfur
Silicon
Chromium
Nickel
Molybdenum
Nitrogen
Other Elements
Austenitic Grades
Cu 0.75
...
...
...
...
...
Cb 0.100.30,
V 0.100.30
...
...
...
...
...
Cu 0.751.25
...
...
...
...
...
...
...
...
...
...
Ce 0.030.08
...
...
Cb 103C-1.10
...
...
Cb 103C-1.10
Cu 0.501.00
NOTICE: This standard has either been superceded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
A 276 02a
TABLE 1 Continued
Composition, %
UNS
DesignationB
Type
S31400
S31600
S31603
S31635
S31640
S31651
S31653
S31654
S31700
S31725
S31726
S32100
S32654
S34565
S34700
S34800
314
316
316LC
316Ti
316Cb
316N
316LN
...
317
...
...
321
...
...
347
348
Carbon
Manganese
Phosphorus
Sulfur
Silicon
Chromium
Nickel
0.25
0.08
0.030
0.08
0.08
0.08
0.030
0.03
0.08
0.030
0.030
0.08
0.020
0.030
0.08
0.08
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.04.0
5.07.0
2.00
2.00
0.045
0.045
0.045
0.045
0.045
0.045
0.045
0.045
0.045
0.045
0.045
0.045
0.030
0.030
0.045
0.045
0.030
0.030
0.030
0.030
0.030
0.030
0.030
0.030
0.030
0.030
0.030
0.030
0.005
0.010
0.030
0.030
1.503.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
0.50
1.00
1.00
1.00
23.026.0
16.018.0
16.018.0
16.018.0
16.018.0
16.018.0
16.018.0
16.018.0
18.020.0
18.020.0
17.020.0
17.019.0
24.025.0
23.025.0
17.019.0
17.019.0
19.022.0
10.014.0
10.014.0
10.014.0
10.014.0
10.014.0
10.013.0
10.013.0
11.015.0
13.517.5
14.517.5
9.012.0
21.023.0
16.018.0
9.012.0
9.012.0
...
2.003.00
2.003.00
2.003.00
2.003.00
2.003.00
2.003.00
2.003.00
3.04.0
4.05.0
4.05.0
...
7.08.0
4.05.0
...
...
...
...
...
0.10
0.10
0.100.16
0.100.16
0.160.30
0.10
0.20
0.100.20
...
0.450.55
0.400.60
...
...
...
...
...
Ti 53(C+N)-0.70
Cb 103C-1.10
...
...
...
...
...
...
Ti 53(C+N)-0.70D
Cu 0.300.60
Cb 0.10
Cb 103C1.10
Cb 103C1.10,
Ta 0.10
Co 0.20
6.07.0
4.56.5
4.56.5
3.05.5
4.56.5
6.08.0
...
2.53.5
3.03.5
0.050.60
2.93.9
3.04.0
...
0.080.20
0.140.20
0.050.20
0.100.25
0.200.30
Ti 0.25
...
...
Cu 0.050.60
Cu 1.502.50
Cu 0.501.00
W 0.501.00
...
...
...
0.040
Al 0.100.30
Cb 103(C+N)0.80
...
...
Ti+Cb 0.20+4 3
(C+N)0.80
...
Cu 0.20
Cb 0.050.20
C+N 0.025
Cu 0.15
C+N 0.025
Cu 0.15
Molybdenum
Nitrogen
Other Elements
Austenitic-Ferritic Grades
S31100
S31803
S32205
S32304
S32550
S32760E
XM-26
...
...
...
...
...
0.06
0.030
0.030
0.030
0.04
0.030
1.00
2.00
2.00
2.50
1.50
1.00
0.045
0.030
0.030
0.040
0.040
0.030
0.030
0.020
0.020
0.030
0.030
0.010
1.00
1.00
1.00
1.00
1.0
1.00
25.027.0
21.023.0
22.023.0
21.524.5
24.027.0
24.026.0
S40500
S40976
405
...
0.08
0.030
1.00
1.00
0.040
0.040
0.030
0.030
1.00
1.00
11.514.5
10.511.7
0.50
0.751.00
S42900
S43000
S44400
429
430
444
0.12
0.12
0.025
1.00
1.00
1.00
0.040
0.040
0.040
0.030
0.030
0.030
1.00
1.00
1.00
14.016.0
16.018.0
17.519.5
...
...
1.00
...
...
1.752.50
...
...
0.035
S44600
S44627
446
XM-27F
0.20
0.010G
1.50
0.40
0.040
0.020
0.030
0.020
1.00
0.40
23.027.0
25.027.5
0.75
0.50
...
0.751.50
0.25
0.015G
S44700
...
0.010
0.30
0.025
0.020
0.20
28.030.0
0.15
3.54.2
0.020
S44800
...
0.010
0.30
0.025
0.020
0.20
28.030.0
2.002.50
3.54.2
0.020
...
...
...
1.252.50
4.07.0
3.55.5
...
0.350.85
1.252.50
...
...
...
...
...
...
...
1.502.00
0.501.00
...
0.400.85
...
0.75
0.75
0.75
...
...
...
...
0.060.12
...
...
...
...
...
...
...
Ferritic Grades
Martensitic Grades
S40300
S41000
S41040
S41400
S41425
S41500
S42000
S42010
S43100
S44002
S44003
S44004
403
410
XM-30
414
...
H
420
...
431
440A
440B
440C
0.15
0.080.15
0.18
0.15
0.05
0.05
0.15 min
0.150.30
0.20
0.600.75
0.750.95
0.951.20
1.00
1.00
1.00
1.00
0.501.00
0.501.00
1.00
1.00
1.00
1.00
1.00
1.00
0.040
0.040
0.040
0.040
0.020
0.030
0.040
0.040
0.040
0.040
0.040
0.040
0.030
0.030
0.030
0.030
0.005
0.030
0.030
0.030
0.030
0.030
0.030
0.030
0.50
1.00
1.00
1.00
0.50
0.60
1.00
1.00
1.00
1.00
1.00
1.00
11.513.0
11.513.5
11.013.0
11.513.5
12.015.0
11.514.0
12.014.0
13.515.0
15.017.0
16.018.0
16.018.0
16.018.0
...
...
Cb 0.050.30
...
Cu 0.30
...
...
...
...
...
...
...
NOTICE: This standard has either been superceded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
A 276 02a
TABLE 2 Mechanical Requirements
Type
Condition
Finish
ksi
MPa
ksi
MPa
Elongation in 2
in. (50 mm)B
or 4D
min %
all
95
655
45
310
30
50
...
all
75
515
40
275
40
45
...
all
all
all
125
125
100
860
860
690
50
50
50
345
345
345
40
40
50
40
40
60
255
311
...
all
100
690
60
414
40
50
...
all
100
690
55
380
35
55
...
up to 2 (50.8), incl
135
930
105
725
20
50
...
115
795
75
515
25
50
...
100
690
60
415
30
50
...
95
655
50
345
35
55
241
all
90
620
50
345
45
60
...
all
100
690
55
380
30
50
...
all
100
690
55
380
30
50
...
all
115
795
60
415
35
40
...
all
110
760
60
410
35
Diameter or Thickness,
in. (mm)
Tensile
Strength,
min
Yield Strength,A
min
Reduction of
Area,C
min, %
Brinell
Hardness,D
max
Austenitic Grades
N08367
201, 202
S20161
S20162
205
XM-19
A
As
hotrolled
S21800
XM-10, XM-11
XM-29
XM-28
S24565
S28200
hot-finished or
cold-finished
hot-finished or
cold-finished
hot-finished
cold-finished
hot-finished or
cold finished
hot-finished or
cold-finished
hot-finished or
cold-finished
hot-finished or
cold-finished
hot-finished or
cold-finished
hot-finished or
cold-finished
hot-finished or
cold-finished
hot-finished or
cold-finished
hot-finished or
cold-finished
hot-finished or
cold finished
hot-finished
cold-finished
hot-finished
cold-finished
304N, 316N
hot-finished or
cold-finished
cold-finished
XM-21, S30454,
S31654
XM-21, S30454
S31654
A
B
cold-finished
hot-finished or
cold-finished
cold-finished
55
...
all
up to 12 (12.70) incl
over 12(12.70)
75
90
75E
515
620
515
30
45
30E
205
310
205
40
30
30
50
40
40
...
...
...
all
up to 12 (12.70) incl.
over 12 (12.70)
all
70
90
70
80
485
620
485
550
25
45
25
35
170
310
170
240
40F
30
30
30
50
40
40
...
...
...
...
...
up to 34 (19.05) incl
125
860
100
690
12
35
...
over (19.05) to
1 (25.40)
over 1 (25.40) to 114
(31.75)
over 114 (31.75) to 112
(38.10)
over 112 (38.10) to 134
(44.45)
up to 2 (50.8) incl
over 2 to 212 (50.8 to 63.5)
incl
over 212 to 3 (63.5 to 76.2)
incl
all
115
795
80
550
15
35
...
105
725
65
450
20
35
...
100
690
50
345
24
45
...
95
655
45
310
28
45
...
95
90
650
620
75
65
515
450
25
30
40
40
...
...
80
550
55
380
30
40
...
90
620
50
345
30
50
...
up to 1 (25.40) incl
145
1000
125
860
15
45
...
135
930
115
795
16
45
...
135
895
105
725
17
45
...
125
860
100
690
18
45
...
34
NOTICE: This standard has either been superceded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
A 276 02a
TABLE 2 Continued
Type
Condition
S30815
S31254
S31725
S31726
S32654
Finish
hot-finished or
cold-finished
hot-finished or
cold-finished
hot-finished or
cold-finished
hot-finished or
cold-finished
hot-finished or
cold-finished
ksi
MPa
ksi
MPa
Elongation in 2
in. (50 mm)B
or 4D
min %
all
87
87
95
600
600
650
45
45
44
310
310
300
40
40
35
50
50
50
...
...
...
all
75
515
30
205
40
...
...
all
80
550
35
240
40
...
...
all
109
750
62
430
40
40
250
Diameter or Thickness,
in. (mm)
all
Tensile
Strength,
min
Yield Strength,A
min
Reduction of
Area,C
min, %
Brinell
Hardness,D
max
Austenitic-Ferritic Grades
XM-26
S31803
S32205
S32304
S32550
S32550
S32760
S
A
S32760
405G
429
430
S40976
S44400
446, XM-27
S44700
S44800
hot-finished or
cold-finished
hot-finished
cold-finished
hot-finished or
cold-finished
hot-finished
cold-finished
hot-finished or
cold-finished
cold-finished
hot-finished or
cold-finished
cold-finished
all
90
620
65
450
20
55
...
all
all
all
90
90
95
620
620
655
65
65
65
448
448
450
25
25
25
...
...
...
290
290
290
all
87
600
58
400
25
...
290
all
109
750
80
550
25
...
290
all
all
125
109
860
750
105
80
720
550
16
25
...
...
335
290
all
125
860
105
720
16
...
335
all
all
all
all
all
...
...
70
70
60
...
...
480
480
415
...
...
40
40
30
...
...
275
275
207
...
...
20
16
20
...
...
45
45
45
207
217
...
...
...
all
60
415
20
140
20
45
244
all
all
all
all
all
all
all
all
60
60
65
65
70
75
70
75
415
415
450
450
480
520
480
520
45
45
40
40
55
60
55
60
310
310
275
275
380
415
380
415
20
16
20
16
20
15
20
15
45
45
45
45
40
30
40
30
217
217
219
219
...
...
...
...
all
all
all
all
all
all
all
all (rounds only)
all
all
all
70
70
100
100
125
125
120
120
70
70
...
480
480
690
690
860
860
830
830
480
480
...
40
40
80
80
100
100
90
90
40
40
...
275
275
550
550
690
690
620
620
275
275
...
20
16
15
12
13
12
12
12
13
12
...
45
45
45
40
45
35
40
40
45
35
...
...
...
...
...
302
...
...
...
235
...
298
all
115
790
90
620
15
45
...
all
all
120
115
825
795
95
90
655
620
15
15
45
45
321
295
all
all
all
all
all
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
241
255
235
255
285
Ferritic Grades
hot-finished
cold-finished
hot-finished
cold-finished
hot-finished or
cold-finished
hot-finished or
cold-finished
hot-finished
cold-finished
hot-finished
cold-finished
hot-finished
cold-finished
hot-finished
cold-finished
Martensitic Grades
403, 410
403, 410
XM-30
403, 410
XM-30
414
414
S41425
S41500
T
T
420
S42010
431
hot-finished
cold-finished
hot-finished
cold-finished
hot-finished
cold-finished
hot-finished
cold-finished
hot-finished
cold-finished
hot-finished or
cold-finished
hot-finished or
cold-finished
hot-finished
hot-finished or
cold-finished
hot-finished
cold-finished
hot-finished
cold-finished
hot-finished or
cold-finished
NOTICE: This standard has either been superceded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
A 276 02a
TABLE 2 Continued
Type
Condition
Finish
Diameter or Thickness,
in. (mm)
hot-finished
cold-finished
all
all
ksi
MPa
ksi
MPa
Elongation in 2
in. (50 mm)B
or 4D
min %
...
...
...
...
...
...
...
...
...
...
Tensile
Strength,
min
Yield Strength,A
min
Reduction of
Area,C
min, %
Brinell
Hardness,D
max
...
...
269
285
A
Yield strength shall be determined by the 0.2 % offset method in accordance with Test Methods and Definitions A 370. An alternative method of determining yield
strength may be used based on a total extension under load of 0.5 %.
B
For some specific products, it may not be practicable to use a 2-in. or 50-mm gage length. The use of sub-size test specimens, when necessary, is permissible in
accordance with Test Methods and Definitions A 370.
C
Reduction of area does not apply on flat bars 316 in. (4.76 mm) and under in thickness as this determination is not generally made in this product size.
D
Or equivalent Rockwell hardness.
E
For extruded shapes of all Cr-Ni grades of Condition A, the yield strength shall be 25 ksi (170 MPa) min and tensile strength shall be 70 ksi (480 MPa) min.
F
For shapes having section thickness of 12 in. (12.5 mm) or less, 30% min. elongation is acceptable.
G
Material shall be capable of being heat treated to a maximum Brinell hardness of 250 when oil quenched from 1750F (953C).
Heat Treatment
TemperatureB
F (C), min
1750
1750
1750
1825
1850
1875
1875
1875
1875
(955)
(955)
(955)
(995)
(1010)
(1020)
(1020)
(1020)
(1020)
Quenchant
Hardness
HRC, min
Air
Air
Oil
Air
Oil
Oil
Air
Oil
Air
35
35
42
50
48
40
55
56
58
A
Samples for testing shall be in the form of a section not exceeding 38 in. (9.50
mm) in thickness.
B
Temperature tolerance is 625F (14C).
NOTICE: This standard has either been superceded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
A 276 02a
ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned
in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk
of infringement of such rights, are entirely their own responsibility.
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and
if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards
and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the
responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should
make your views known to the ASTM Committee on Standards, at the address shown below.
This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,
United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above
address or at 610-832-9585 (phone), 610-832-9555 (fax), or service@astm.org (e-mail); or through the ASTM website
(www.astm.org).