Professional Documents
Culture Documents
If UE is traveling continuously from one cell to another. It would have to transit multiple
time to CELL_FACH state for location update. By assigning URA_PCH state, this
condition is avoided, since 1 URA contains one or more cells and vice versa.
3) In which conditions UE will be in Cell FACH state?
This happens when,
UE doesnt require continuous circuit connection with n/w, but DL packets will work.
UE is forced to release the n/w resources to decrease the congestion problems (flipflop between DCH and FACH).
Eventual location updates to support CELL_PCH and URA_PCH states (flip-flop
between FACH and PCH).
E.g. Call on hold(CS), File downloading(PS)
4) What is the difference between Cell PCH and URA PCH state?
UE is known on URA(UTRAN Registration Area) level rather than cell level
If UE is traveling continuously from one cell to another. It would have to transit multiple
time to CELL_FACH state for location update. By assigning URA_PCH state, this
condition is avoided, since 1 URA contains one or more cells and vice versa
5) What is U-RNTI?
URNTI is a 32bit identity.
SRNC identifier + SRNTI makes URNTI
6) Describe the CELL search procedure?
The Cell Search procedure can be summarised into the following steps:
a. Cell Selection: Determine the cell whose received carrier power is the strongest
b. Slot Synchronisation: the UE reads the P-SCH of the strongest carrier and feeds the
received signal through a matched filter (that is matched to the Primary
Synchronisation Code). The slot timing is detected via detection of peaks in the
output of the matched filter.
c. Frame Synchronisation and Scrambling Code Group Identification: the UE reads
the S-SCH of the strongest carrier, and correlates the received signal with all the
possible 64 Secondary Synchronisation Codes. The output that gives maximum
correlation gives the group of the Primary Scrambling Code used in the cell. This
process also gives the frame timing since the Secondary Synchronisation Code is
different for each slot and the group tells the mapping between slots and SSCs.
d. Scrambling Code Identification: The UE attempts then to read the P-CPICH so as
to extract the Primary Scrambling Code used in the cell. The P-CPICH is always
scrambled by the Primary Scrambling Code of the cell and is spread a factor 256 and
an OVSF whose index is zero. Since the Primary Scrambling Codes are grouped into
64 groups of 8 Scrambling Codes and the S-SCH has
given the Scrambling Code group only 8 possibilities remain. So the P-CPICH is
unscrambled separately withevery possible Scrambling Code (8) in the group and
only one output will produce correct results and the Primary Scrambling Code of the
cell is determined.
e. Read Broadcast Information: Since the P-CCPCH is always scrambled by the
Primary Scrambling Code of the cell (which has now been determined) and is always
spread using SF=256 with OVSF index=1, The UE can read the P-CCPCH without
any problem. The P-CCPCH carries the BCH where system information blocks are
broadcast throughout the entire cell. The UE can acquire at this stage various
information (e.g. Spreading Factors, OVSF indexes and Scrambling Codes used in
other downlink channels, important
interference). It may however also be performed for other reasons such as system
load control.
9) What are types of measurements?
Intra-frequency measurements: measurements on downlink physical channels at the
same frequency as the active set. A measurement object corresponds to one cell.
Inter-frequency measurements: measurements on downlink physical channels at
frequencies that differ from the frequency of the active set and on downlink physical
channels in the active set. A measurement object corresponds to one cell.
Inter-RAT measurements: measurements on downlink physical channels belonging to
another radio access technology than UTRAN, e.g. GSM. A measurement object
corresponds to one cell.
Traffic volume measurements: measurements on uplink traffic volume. A
measurement object corresponds to one cell.
Quality measurements: Measurements of downlink quality parameters, e.g. downlink
transport block error rate. A measurement object corresponds to one transport
channel in case of BLER. A measurement object corresponds to one timeslot in case
of SIR (TDD only).
UE-internal measurements: Measurements of UE transmission power and UE
received signal level.
UE positioning measurements: Measurements of UE position.
10) What is paging? Why paging is required?
Paging: This procedure is used to transmit paging information to selected UEs in idle
mode, CELL_PCH or URA_PCH state using the paging control channel (PCCH).
Paging can be initiated :
Upper layers in the network may request paging, to e.g. establish a signaling
connection.
UTRAN may initiate paging for UEs in CELL_PCH or URA_PCH state to trigger a cell
update procedure.
UTRAN may initiate paging for UEs in idle mode, CELL_PCH and URA_PCH state to
trigger reading of updated system information.
UTRAN may also initiate paging for UEs in CELL_PCH and URA_PCH state to release
the RRC connection.
11) Type of Paging?
Paging Type 1
Paging Type 2(UE dedicated paging)
12) When dedicated paging is used?
a. This procedure is used to transmit dedicated paging information to one UE in
connected mode in CELL_DCH , CELL_FACH or CELL_PCH (FDD only) state.
Upper layers in the network may request initiation of paging.
b. For a UE in CELL_DCH, CELL_FACH or CELL_PCH (FDD only) state, UTRAN
initiates the procedure by transmitting a PAGING TYPE 2 message on the DCCH
using AM RLC. When not stated otherwise elsewhere, the UTRAN may initiate the
UE dedicated paging procedure also when another RRC procedure is ongoing, and
in that case the state of the latter procedure shall not be affected.
c. UTRAN should set the IE "Paging cause" to the cause for paging received from upper
layers. If no cause for paging is received from upper layers, UTRAN should set the
value "Terminating cause unknown".
13) In what situation UE goes to CELL PCH and URA PCH states?
a. Cell PCH:
if none of the criteria for performing cell update with the causes specified above in
the current subclause is met:
if the UE is in CELL_FACH or CELL_PCH state and the UE performs cell reselection; or
if the UE is in CELL_FACH state and the variable C_RNTI is empty:
perform cell update using the cause "cell reselection".
Periodical cell update:
if none of the criteria for performing cell update with the causes specified above in
the current subclause is met; and
if the UE is in CELL_FACH or CELL_PCH state; and
if the timer T305 expires; and
if the criteria for "in service area" and
if periodic updating has been configured by T305 in the IE "UE Timers and constants
in connected mode" set to any other value than "infinity":
perform cell update using the cause "periodical cell update".
MBMS reception:
if none of the criteria for performing cell update with the causes specified above in
the current subclause is met; and
if the UE is in URA_PCH, Cell_PCH or Cell_FACH state; and
if the UE should perform cell update for MBMS counting ,
perform cell update using the cause "MBMS reception".
15) What is Active set?
Active Set is defined as the set of Node-Bs the UE is simultaneously connected to
(i.e., the UTRA cells currently assigning a downlink DPCH to the UE constitute the
active set).
16) What is Monitor set and detected set Cells?
a. Cells, which are not included in the active set, but are included in the
CELL_INFO_LIST belong to the Monitored Set.
b. Cells detected by the UE, which are neither in the CELL_INFO_LIST nor in the active
set belong to the Detected Set. Reporting of measurements of the detected set is
only applicable to intra-frequency measurements made by UEs in CELL_DCH state.
17) What are the various types of RNC?
a. Serving RNC
b. Drift RNC
c. Controlling RNC
18) What is the use and difference between CRNC, Drift RNC and SRNC?
RNC from which the UE is currently getting Served or connected to is called SRNC or
Serving RNC.
During a soft handover procedure the RNC UE is moving to, is called Drift RNC.
The RNC which controls the movement of UE from Serving RNC to the Drift RNC is
called Controlling RNC.
19) What is initial direct transfer message? What is the use?
The initial direct transfer procedure is used in the uplink to establish a signaling
connection. It is also used to carry an initial upper layer (NAS) message over the
radio interface.
20) What is security mode command? Why it is used?
Security mode command is a RRC Message,
The purpose of this procedure :
To trigger the start of ciphering or to command the restart of the ciphering with a new
ciphering configuration, for the radio bearers of one CN domain and for all signalling
radio bearers.
It is also used to start integrity protection or to modify the integrity protection
configuration for all signalling radio bearers
21) What is CCTrCH?
A Coded Composite Transport Channel is the result of combining (multiplexing)
several Transport Channels of the same type; i.e.: we can have a CCTrCh made up
of one or several DCHs, a CCTrCh made up of DSCHs. One exception is that we can
have one or several FACHs multiplexed with a PCH on the same CCTrCh.
A better notation would be for example:
CCTrCh4DCH: A CCTrCh consisting of 4 DCHs
CCTrCh3FACH: A CCTrCh consisting of 3 FACHs
CCTrChPCH,2FACH: A CCTrCh consisting of the PCH and 2 FACHs
22) What is compressed mode?
Higher layers can request a UE to monitor cells on other frequencies (FDD, TDD), or
other systems (GSM). This implies that the UE has to perform measurements, on the
other frequencies/systems and thus higher layers command the UE to enter
Compressed Mode. The UTRAN need to send to the UE all the parameters for the
Compressed Mode.
Compression Methods:
When in Compressed Mode the information normally transmitted during a 10 ms
frame is compressed in time sothat gaps of adequate length are created. To achieve
this one of three mechanisms
Puncturing
This method is NOT applicable to downlink.
Spread Factor Reduction
Actually halving the Spread Factor. So with this method if SF is used in noncompressed frames then SF/2 is used in the compressed frames.
Higher Layer Scheduling
Higher Layers set restrictions so that only a subset of allowed TFCs are used in
Compressed Mode.
Compressed Mode Parameter:
TGSN (Transmission Gap Starting Slot Number): A transmission gap pattern begins
in a radio frame, called firstradio frame of the transmission gap pattern, containing at
least one transmission gap slot. TGSN is the slot numberof the first transmission gap
slot within the first radio frame of the transmission gap pattern;
TGL1 (Transmission Gap Length 1): Duration of the first transmission gap within the
transmission gap pattern, expressed in number of slots;
TGL2 (Transmission Gap Length 2): Duration of the second transmission gap within
the transmission gap pattern, expressed in number of slots. If this parameter is not
explicitly set by higher layers, then TGL2 =TGL1;
TGD (Transmission Gap Start Distance): Duration between the starting slots of two
consecutive transmission gaps within a transmission gap pattern, expressed in
number of slots. The resulting position of the second transmission gap within its radio
frame(s) shall comply with the limitations of TS 25.101 (Ref [2]). If this parameter is
not set by higher layers, then there is only one transmission gap in the transmission
gap pattern;
TGPL1 (Transmission Gap Pattern Length): Duration of transmission gap pattern 1;
Enabled
Disabled
If
MNO I
It will perform a combined Attach
If NMOII
It will do a LAU and Attach.
PS
Call
If the network operates in Network Mode Of Operation I i.e. NMO I and GPRS MS
that operates in Mode A or Mode B will do a simultaneous IMSI attach for GPRS and
non GPRS services and shall use the Combined GPRS attach, combined and
periodic routing area updating procedures instead of the corresponding MM specific
procedures IMSI attach and normal and periodic Location area updating.
29) When UE triggers Event 3A Measurement Report?
Event 3A:The Estimated Quality of currently used UTRAN frequency is below a
certain threshold and the estimated quality of the other system is above a certain
threshold.
30) How many transport channels will be configured when a CSV and a PSD call is
simultaneously going on?
Five transport channels will be configured.
1 for 4 SRBs
3 for CSV
1 for PSD
31) When event 2A, 2B, 2C,2E occurs?
Event 2a: Change of best frequency
Event 2b: The estimated quality of the currently used frequency is below a certain
threshold and the estimated quailty of a non-used frequency is above a certain
threshold.
Event 2c: The estimated quality of a non-used frequency is above a certain
threshold
Event 2d: The estimated quality of the currently used frequency is below a certain
threshold
Event 2e: The estimated quality of a non-used frequency is below a certain
threshold
32) When event 1A 1F Event occurs?
event 1A: A Primary CPICH enters the reporting range
event 1B: A primary CPICH leaves the reporting range
event 1C: A non-active primary CPICH becomes better than an active primary
CPICH
event 1D: Change of best cell
event 1E: A Primary CPICH becomes better than an absolute threshold
event 1F: A Primary CPICH becomes worse than an absolute threshold
33) Where CK and IK gets generated?
In RRC CK and IK gets generated.
34) Where CK and IK gets stored?
In USIM CK and IK will get stored.
35) Where the Security procedure will start?
Security Procedure will start in RRC but Ciphering will start for AM and UM data
security procedure will start at RLC layer. And for TM mode security procedure start
at MAC layer.
36) What are the mandatory SIBs which UE has to read before
campign
campaign?
SIB 1, 3,5,7,11
37) What are the important RACH parameters and which SIB contains this information?
SIB 7/5
38) Which SIB contains S criteria information?
SIB 3