Professional Documents
Culture Documents
com
KH300
Wideband, High-Speed Operational Amplifier
Features
General Description
Applications
Digital communications
Baseband and video communications
Instrument input/output amplifiers
Fast A to D, D to A conversion
Graphic CRT video drive amp
Coaxial cable line driver
V+
V-
16
+VCC
12
Vo
11
Rf
1500
13
24
-VCC GND
The KH300 operational amplifier is a current feedback amplifier that provides a DC-85MHz -3dB bandwidth that is virtually independent of gain setting.
Rise and fall times of 4ns and drive capability of
22Vpp and 100mA add to the KH300s impressive
specifications.
Using the KH300 is as easy as adding power supplies
and a gain-setting resistor. Unlike conventional op
amp designs in which optimum gain-bandwidth
product occurs at a high gain, minimum settling time
at a gain of -1, maximum slew rate at a gain of +1,
et cetera, the KH300 offers consistent performance
at gain settings from 1 to 40 inverting or non-inverting.
As a result, designing with the KH300 is greatly
simplified. And since no external compensation is
necessary, tweeks on the production line have been
eliminated, making the KH300 an efficient
component for use in production situations.
Flat gain and phase response from DC to 45MHz and
superior rise and fall times make the KH300 an ideal
amplifier for a broad range of pulse, analog, and
digital applications. A 45MHz full power bandwidth
(20Vpp into 100) and 3000V/sec slew rate eliminate
the need for power buffers in many applications
such as driving flash A to D converters or linedriving. For applications requiring lower power
consumption, the KH300 can operate on supplies as
low as 5V. Fast overload recovery (20ns) helps
prevent loss of data in communications applications
and flat phase response reduces distortion, even when
data must be sent over extended lengths of line.
The KH300A is packaged in a side-brazed 24-pin
ceramic DIP and is specified at 25C.
DATA SHEET
KH300
4*
TYP
MIN2
TYP
Vo < 4Vpp
Vo = 20Vpp
100KHz to 20MHz
20MHz to 45MHz
105
45
0.25
0.5
1
2
60
75
85
45
0.08
0.25
1.6
3
70
DC to 45MHz
40
MAX2
0.3
0.6
TYP
UNITS
70
45
0.25
1
2
5
70
MHz
MHz
dB
dB
deg/MHz
deg
dB
5
7
25
5
3
20
ns
ns
ns
%
V/s
ns
refer to graphs
5V output step
20V output step
settling time to 0.8%
10V output step
overshoot (input rise time 1ns) 5V output step
slew rate
overload recovery (200% od)
< 50ns pulse width
General Information
20
CONDITIONS
3
7
20
5
3
20
4
7
20
5
3
20
MIN2
CONDITIONS
non-inverting
inverting
equivalent input noise1
integrated 0.1 to 100MHz,
(Rs = 50, gain = 20)
second/third harmonic distortion 20MHz, +10dBm
input impedance
non-inverting
power supply rejection ratio
input referred
common mode rejection ratio
input referred
output drive voltage,current
supply current
45
TYP
MAX2
UNITS
10(25)
10(20)
30(50)
22
32
30
100
56
mV(V/C)
V(nA/C)
V(nA/C)
V
48
100K/3
60
64
10, 100
24
38
-dBc
/pF
dB
dB
V, mA
mA
33
Min/max ratings are based on product characterization and simulation. Individual parameters are tested as noted. Outgoing quality levels are
determined from tested parameters.
NOTES:
KH300
DATA SHEET
Inverting Gain
Non-Inverting Gain
Av = 4
Av = 20
Av = 40
10
20
30
40
50
60
70
80
90 100
Av = 4
Av = 20
Av = 40
10
20
Freguency (MHz)
30
40
50
60
70
Av = 20
-180
Inverting
-90
-270
Non-inverting
Non-inverting
Inverting
-180
100 200 300 400 500 600 700 800 900 1GHz
-360
10
20
Freguency (MHz)
30
40
50
60
70
80
90 100
Freguency (MHz)
90
50
80
Av = 20
Av = 20
90 100
Av = 20
(I2)
2nd harmonic intercept
exceeds 90dBm below 105Hz
70
60
50
(I3)
3rd harmonic intercept
exceeds 64dBm below 105Hz
40
30
45
40
35
30
25
104
105
106
107
108
20
40
60
80
100
Freguency (Hz)
Freguency (MHz)
Av = 20
Time (5ns/div)
80
Freguency (MHz)
Time (5ns/div)
DATA SHEET
KH300
Settling Time
0.4
Av = -20
10V step
Av = 20
0.2
0
-0.2
-0.4
-0.6
-0.8
Time (5ns/div)
200
400
600
800
1000
Time (ns)
Relative Bandwidth vs. VCC
1.1
Relative Bandwidth
Av = 20
1.0
0.9
0.8
0.7
150C max TJ
VCC = 15V
2.0
Case
Ambient
1.5
1.0
0.5
4
10
14
12
-25
16
VCC (V)
Equivalent Input Noise
10
10
Voltage
2.9nV/Hz
Non-inverting Current
2.3pA/Hz
1
105
100
106
107
108
Frequency (Hz)
70
CMRR (dB)
Inverting Current
11pA/Hz
104
75
80
100
103
50
100
102
25
Temperature (C)
60
50
40
30
101
102
103
104
105
106
107
Frequency (Hz)
CMRR (dB)
70
60
50
40
30
101
102
103
104
105
106
Frequency (Hz)
KH300
DATA SHEET
Layout Considerations
To assure optimum performance the user should follow
good layout practices which minimize the unwanted
coupling of signals between nodes. During initial breadboarding of the circuit, use direct point to point wiring,
keeping lead lengths to less than 0.25. The use of
solid, unbroken ground plane is helpful. Avoid wire-wrap
type pc boards and methods. Sockets with small, short
pin receptacles may be used with minimal performance
degradation although their use is not recommended.
+15
22F
0.01F
16
Vin
6
Ri
50
Rg
+
11
KH300
24
12
Ro
1/2 Vo
50
RL
50
13
-15
22F
0.01F
Av = 1 +
Rf
Rg
Rf = 1500 (internal)
22F
0.01F
51
Rg
Vin
Ri
50
16
+
11
KH300
24
12
13
Ro
50
1/2 Vo
RL
50
Rf
(K)
Cc
(pF)
f0.3dB
(MHz)
f-3.0dB
(MHz)
10.0
5.0
2.0
1.5
1.0
0.75
0.50
0
0
0
0
0.3
1.1
1.9
2
3
8
45
90
95
110
5
12
40
85
115
130
135
-15
22F
0.01F
DATA SHEET
KH300
in 2R f 2
A v2
4 kTR s f
DATA SHEET
KH300
b1
Pin #1
Index
Q
A
L
E1
E
e
D1
D
A1
Symbol
Inches
Minimun
Milimeters
Maximum
Minimum
Maximum
A-Metal Lid
0.180
0.240
4.57
6.10
A-Ceramic Lid
0.195
0.255
4.95
6.48
A1-Metal Lid
0.145
0.175
3.68
4.45
A1-Ceramic Lid
0.160
0.190
4.06
4.83
0.014
0.026
0.36
0.66
b1
0.050 BSC
1.27 BSC
0.008
0.018
0.20
0.46
1.275
1.310
33.39
33.27
D1
1.095
1.105
27.81
28.07
0.785
0.815
19.94
20.70
E1
0.790
0.810
20.07
20.57
0.100 BSC
2.54 BSC
0.165 BSC
4.19 BSC
0.015
0.075
NOTES:
Seal: seam weld (AM, AK), epoxy (AI)
Lead finish: gold finish
0.38
1.91
Package composition:
Package: ceramic
Lid: kovar/nickel (AM, AK),
ceramic (AI)
Leadframe: alloy 42
Die attach: epoxy
DISCLAIMER
FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICES TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD
DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT
RIGHTS, NOR THE RIGHTS OF OTHERS.
LIFE SUPPORT POLICY
FAIRCHILDS PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT
OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein:
1.
Life support devices or systems are devices or systems which, (a) are intended for
surgical implant into the body, or (b) support or sustain life, and (c) whose failure to
perform when properly used in accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a significant injury of the user.
www.fairchildsemi.com
2.