Professional Documents
Culture Documents
10
104
10.1 General
This clause defines the GPS scenarios and assistance data IEs which shall be available for use as specified in all A-GPS
test cases in 3GPP TS 34.171 [41] and 3GPP TS 34.123-1 [1].
The information elements are given with reference to 3GPP TS 25.331 [34], where the details are defined.
Clauses 10.2 and 10.3 list the assistance data IEs required for performance testing of UE-based mode detailed in
3GPP TS 34.171 [41], and clauses 10.4 and 10.5 list the assistance data available for performance testing of UE-assisted
mode detailed in 3GPP TS 34.171 [41]. Clause 10.6 lists the values of the assistance data IE fields for performance
testing detailed in 3GPP TS 34.171 [41].
Clause 10.7 details the GPS scenario and the values of the assistance data IE fields for signalling testing detailed in
3GPP TS 34.123-1 [1], clause 17.2.
The A-GPS minimum performance requirements are defined by assuming that all relevant and valid assistance data is
received by the UE in order to perform GPS measurements and/or position calculation. This clause does not include nor
consider delays occurring in the various signalling interfaces of the network.
10.1.2.1
GPS Scenario #1
The following GPS scenario #1 shall be used during the TTFF tests defined in TS 34.171 [41]. The assistance data
specified in the following sections for GPS scenario #1 is consistent with this GPS scenario.
Yuma Almanac data: see file GPS 1 Yuma.txt in the GPS data perf zip file specified in annex C.2.
UE location: the UE location is calculated as a random offset from the reference location using the method described in
section 10.1.2.4. The reference location is: latitude: 33 degrees 45 minutes 0.019 seconds north, longitude: 84 degrees
23 minutes 0.011 seconds west, (Atlanta USA), height: = 300m.
Nominal start time: 22nd January 2005 (Saturday) 00:08:00.
Viable running time to maintain specified HDOP values: 19 minutes.
Visible satellites available for simulation and for which Assistance Data (other than Almanac) shall be generated: PRNs:
2, 6, 10, 17, 18, 21, 26, 29, 30.
3GPP
Release 6
105
10.1.2.2
GPS Scenario #2
The following GPS scenario #2 shall be used during the TTFF tests defined in TS 34.171 [41]. The assistance data
specified in the following sections for GPS scenario #2 is consistent with this GPS scenario.
Yuma Almanac data: see file GPS 2 Yuma.txt in the GPS data perf zip file specified in annex C.2.
UE location: the UE location is calculated as a random offset from the reference location using the method described in
section 10.1.2.4. The reference location is: latitude: 37 degrees 48 minutes 59.988 seconds south, longitude: 144 degrees
58 minutes 0.013 seconds east, (Melbourne Australia), height: = 100m.
Nominal start time: 22nd January 2004 (Thursday) 00:08:00.
Viable running time to maintain specified HDOP values: 19 minutes.
Visible satellites available for simulation and for which Assistance Data (other than Almanac) shall be generated: PRNs:
3, 11, 14, 15, 18, 22, 23, 25, 31.
Ionospheric model: see values in section 10.6.6.
Tropospheric model: STANAG with SRI equal to 324.8, as defined in [43].
10.1.2.3
GPS Scenario #3
The following GPS scenario #3 shall be used during the Moving Scenario and Periodic Update test case defined in TS
34.171 [41]. The assistance data specified in the following sections for GPS scenario #3 is consistent with this GPS
scenario.
Yuma Almanac data: see file GPS 3 Yuma.txt in the GPS data perf zip file specified in annex C.2.
UE location: the UE location is given as a trajectory as shown in Figure 5.6.1 of TS 34.171 [41]. The reference location
is at the centre of the trajectory and is at: latitude: 37 degrees 48 minutes 59.988 seconds south, longitude: 144 degrees
58 minutes 0.013 seconds east, (Melbourne Australia), height: = 100m.
Start time: 22nd January 2004 (Thursday) 00:08:00.
Start location: at the point between l11 and l12 in Figure 5.6.1 of TS 34.171 [41], going in a clock-wise direction.
Visible satellites available for simulation and for which Assistance Data (other than Almanac) shall be generated: PRNs:
3, 11, 14, 15, 18, 22, 23, 25, 31.
Viable running time to maintain specified HDOP values: 19 minutes.
Ionospheric model: see values in section 10.6.6.
Tropospheric model: STANAG with SRI equal to 324.8, as defined in [43].
10.1.2.4
This section defines the method for generating the random UE locations that are required to be used for the TTFF tests
defined in TS 34.171 [41].
For every Test Instance in each TTFF test case, the UE location shall be randomly selected to be within 3 km of the
Reference Location. The Altitude of the UE shall be randomly selected between 0 m to 500 m above WGS-84 reference
ellipsoid. These values shall have uniform random distributions.
The UE location is calculated as an offset from the Reference Location.
10.1.2.4.1
UE Location Offset
The UE location offset shall be calculated by selecting the next pair of random numbers, representing a pair of latitude
and longitude offsets in degrees, from a standard uniform random number generator, with the following properties:
3GPP
Release 6
106
The ranges of the latitude and longitude offsets values shall be such that when translated onto the surface of the
earth they shall lie within a 3km radius circle, centred on the Reference location specified for the GPS scenario
under consideration. For the purposes of this calculation make the following assumptions:
a) Over the 3km radius circle at the Reference location the earth is flat and the meridians and parallels form
a rectangular grid
b) The earth is spherical with a radius of 6371141m (equal to the WGS 84 value at 35 degrees latitude)
The resolution used for the latitude and longitude offsets values shall be 90/2E23 for the latitude offset values
and 360/2E24 for the longitude offset values, representing the coding resolution in degrees specified in TS23.032
[42].
10.1.2.4.2
UE Altitude
The UE altitude value shall be calculated by selecting the next random number from a standard uniform random number
generator, in the range 0 to 500, representing meters. The resolution used for the random number shall be 1,
representing 1 meter.
10.1.2.5
The satellites to be simulated in each test case have been selected in order to achieve the required HDOP for that test
case.
Satellites to be simulated
Test case
Sensitivity Coarse Time
Assistance
Sensitivity Fine Time Assistance
Nominal Accuracy
Dynamic Range
Multi-path Performance
Moving Scenario and Periodic
Update Performance
PRNs GPS #1
2, 6, 10, 17, 18, 21,
26, 29
2, 6, 10, 17, 18, 21,
26, 29
2, 6, 10, 17, 18, 21,
26, 29
2, 6, 10, 17, 26, 29
2, 6, 17, 21, 26
-
PRNs GPS #2
3, 11, 14, 15, 22, 23,
25, 31
3, 11, 14, 15, 22, 23,
25, 31
3, 11, 14, 15, 22, 23,
25, 31
3, 14, 15, 22, 25, 31
3, 14, 15, 22, 25
-
PRNs GPS #3
3, 14, 15, 22, 25
Fields of the IE
GPS Week
GPS TOW msec
GPS TOW Assist
SatID
TLM Message
TLM Reserved
Alert
Anti-Spoof
b) UE positioning GPS reference UE position IE. This information element is defined in clause 10.3.8.4c of
3GPP TS 25.331 [34].
Name of the IE
Reference Location
Fields of the IE
Ellipsoid point with Altitude and uncertainty ellipsoid
3GPP
Release 6
107
c) UE positioning GPS navigation model IE. This information element is defined in clause 10.3.7.94 of
3GPP TS 25.331 [34].
Name of the IE
Navigation Model
Fields of the IE
All satellite information
d) UE positioning GPS ionospheric model IE. This information element is defined in clause 10.3.7.92 of
3GPP TS 25.331 [34].
Name of the IE
Ionospheric Model
Fields of the IE
All
Fields of the IE
GPS Week
GPS TOW msec
UTRAN GPS reference time
>UTRAN GPS timing of cell frames
>CHOICE mode
>>FDD
>>>Primary CPICH Info
>SFN
SFN-TOW Uncertainty
TUTRAN-GPS drift rate
GPS TOW Assist
SatID
TLM Message
TLM Reserved
Alert
Anti-Spoof
Fields of the IE
GPS Week
GPS TOW msec
GPS TOW Assist
SatID
TLM Message
TLM Reserved
Alert
Anti-Spoof
3GPP
Release 6
108
b) UE positioning GPS reference UE position IE. This information element is defined in clause 10.3.8.4c of
3GPP TS 25.331 [34].
Name of the IE
Reference Location
Fields of the IE
Ellipsoid point with Altitude and uncertainty ellipsoid
c) UE positioning GPS almanac This information element is defined in clause 10.3.7.89 of 3GPP TS 25.331 [34].
Name of the IE
UE positioning GPS almanac
Fields of the IE
Almanac Reference Week
All Satellite information
d) UE positioning GPS navigation model IE. This information element is defined in clause 10.3.7.94 of
3GPP TS 25.331 [34].
Name of the IE
Navigation Model
Fields of the IE
All satellite information
e) UE positioning GPS acquisition assistance IE. This information element is defined in clause 10.3.7.88 of
3GPP TS 25.331 [34].
Name of the IE
Acquisition Assistance
Fields of the IE
GPS TOW msec
Satellite information
>SatID
>Doppler (0th order term)
>Extra Doppler
>>Doppler (1st order term)
>>Doppler Uncertainty
>Code Phase
>Integer Code Phase
>GPS Bit number
>Code Phase Search Window
>Azimuth and Elevation
>> Azimuth
>> Elevation
Fields of the IE
GPS Week
GPS TOW msec
UTRAN GPS reference time
>UTRAN GPS timing of cell frames
>CHOICE mode
>>FDD
>>>Primary CPICH Info
>SFN
SFN-TOW Uncertainty
3GPP
Release 6
109
b) UE positioning GPS acquisition assistance IE. This information element is defined in clause 10.3.7.88 of
3GPP TS 25.331 [34].
Name of the IE
Acquisition Assistance
Fields of the IE
GPS TOW msec
UTRAN GPS reference time
>UTRAN GPS timing of cell frames
>CHOICE mode
>>FDD
>>>Primary CPICH Info
>SFN
Satellite information
>SatID
>Doppler (0th order term)
>Extra Doppler
>>Doppler (1st order term)
>>Doppler Uncertainty
>Code Phase
>Integer Code Phase
>GPS Bit number
>Code Phase Search Window
>Azimuth and Elevation
>> Azimuth
>> Elevation
10.6.2.1
For every Test Instance in each TTFF test case, the IE GPS TOW msec shall have a random offset, relative to GPS
system time, within the allowed error range of Coarse Time Assistance defined in the test case. This offset value shall
have a uniform random distribution.
3GPP
Release 6
Note:
110
For the Moving Scenario and Periodic Update Test Case the value of the IE GPS TOW msec shall be set
to the nominal value, i.e. no offset shall be used.
The offset value shall be calculated by selecting the next random number from a standard uniform random number
generator, in the range specified for the GPS Coarse Time assistance error range in the Test Requirements, Test
parameters table for the test under consideration. The resolution used for the random number shall be 0.01, representing
10ms.
10.6.2.1
In addition, for every Fine Time Assistance Test Instance the IE UTRAN GPS timing of cell frames shall have a random
offset, relative to the true value of the relationship between the two time references, within the allowed error range of
Fine Time Assistance defined in the test case. This offset value shall have a uniform random distribution.
The offset value shall be calculated by selecting the next random number from a standard uniform random number
generator with the following properties:
The range shall be the number of UMTS chips whose duration is less than the range specified for the GPS Fine Time
assistance error range in the Test Requirements, Test parameters table for the test under consideration.
The resolution used for the random number shall be 1, representing 1 UMTS chip.
3GPP
Release 6
111
Units
weeks
msec
UTRAN GPS
reference time
>UTRAN GPS
timing of cell
frames
>CHOICE mode
>>FDD
>>>Primary
CPICH Info
>SFN
SFN-TOW
Uncertainty
TUTRAN-GPS
drift rate
Note 1: GPS TOW msec
Value/remark GPS
#1
282
518880000. Start
time. Add number of
ms as required.
(Note 1)
Present for
Sensitivity Fine Time
Assistance test
case. Absent
otherwise
Note 2
Value/remark GPS
#2
230
346080000. Start
time. Add number of
ms as required.
(Note 1)
Present for
Sensitivity Fine Time
Assistance test
case. Absent
otherwise
Note 2
Value/remark GPS
#3
230
346080000. Start
time. Add number of
ms as required.
(Note 1)
Absent
Present for
Sensitivity Fine Time
Assistance test
case. Absent
otherwise
100
Present for
Sensitivity Fine Time
Assistance test
case. Absent
otherwise
100
Note 2
lessThan10
Note 2
lessThan10
This is the value in ms of GPS TOW msec when the GPS scenario is initially started in the GPS
simulator. For all TTFF test cases, each time a GPS scenario is used, the GPS start time shall be
advanced by 120 seconds from the value last used so that, at the time the fix is made, it is at least
2 minutes later than the previous fix made with that scenario.
The actual value of GPS TOW msec to be used in the Reference Time IE (before the addition of the
random offset, if applicable) shall be calculated at the time the IE is required by adding the elapsed
time since the time the scenario was started in the GPS simulator to this value. The accuracy shall
be such that the Maximum Test System Uncertainty for Coarse Time Assistance, specified in Table
F.1.2 of TS 34.171 [41], shall be met.
For all TTFF test cases a random offset is then added to the value of GPS TOW msec as described
in clause 10.6.2
Note 2: UTRAN GPS timing of cell frames and SFN
The values of UTRAN GPS timing of cell frames (before the addition of the random offset) and SFN
shall be calculated at the time the IE is required. The accuracy of the relationship between the two
fields shall be such that the Maximum Test System Uncertainty for Fine Time Assistance, specified
in Table F.1.2 of TS 34.171 [41], shall be met.
A random offset is then added to the value of UTRAN GPS timing of cell frames as described in
clause 10.6.2
Satellite Information
Parameter
Number of satellites
Units
---
3GPP
Value/remark GPS
All
9
Release 6
112
Reference Time - GPS TOW Assist (Fields occurring once per satellite)
Parameter
SatID
Units
Value/remark GPS #1
PRNs: 2, 6, 10, 17, 18,
21, 26, 29, 30
Value/remark GPS #2
PRNs: 3, 11, 14, 15, 18,
22, 23, 25, 31
Value/remark GPS #3
PRNs: 3, 11, 14, 15,
18, 22, 23, 25, 31
Reference Time - GPS TOW Assist (Fields occurring once per satellite)
Parameter
TLM Message
TLM Reserved
Alert
Anti-Spoof
Units
Bit string
Bit string
Boolean
Boolean
Units
Bit field
degrees
Value/remark GPS #1
Ellipsoid point with
altitude and uncertainty
Ellipsoid
33.750005
Value/remark GPS #2
Ellipsoid point with
altitude and uncertainty
Ellipsoid
-37.816663
Value/remark GPS #3
Ellipsoid point with
altitude and uncertainty
Ellipsoid
-37.816663
Degrees of
latitude
Degrees of
longitude
Altitude
Uncertainty
semi-major
Uncertainty
semi-minor
Orientation
of major
axis
Uncertainty
altitude
Confidence
degrees
-84.383517
144.966670
144.966670
m
m
+300
3000
+100
3000
+100
3000
3000
3000
3000
degrees
500
500
500
68
68
68
Units
---
Value/remark GPS
All
9
Units
SatID
---
Satellite
Status
Boolean
Value/remark
GPS #1
PRNs: 2, 6, 10,
17, 18, 21, 26,
29, 30
0 (Note)
3GPP
Value/remark
GPS #2
PRNs: 3, 11, 14,
15, 18, 22, 23,
25, 31
0 (Note)
Value/remark
GPS #3
PRNs: 3, 11, 14,
15, 18, 22, 23,
25, 31
0 (Note)
Release 6
Note:
113
For consistency Satellite Status is also given in file: Navigation model XX.csv
Ephemeris and Clock Correction parameters (Fields occurring once per satellite)
Parameter
C/A or P on L2
URA Index
SV Health
IODC
L2 P Data Flag
SF 1 Reserved
TGD
toc
af2
af1
af0
Crs
n
M0
Cuc
e
Cus
(A)1/2
toe
Fit Interval Flag
AODO
Cic
OMEGA0
Cis
i0
Crc
OMEGAdot
Idot
Units
Boolean
Boolean
Boolean
--Boolean
--sec
sec
sec/sec2
sec/sec
sec
meters
semi-circles/sec
semi-circles
radians
--radians
meters1/2
sec
Boolean
sec
radians
semi-circles
radians
semi-circles
meters
semi-circles
semi-circles/sec
semi-circles/sec
Units
seconds
sec/semi-circle
sec/(semi-circle)2
sec/(semi-circle)3
seconds
sec/semi-circle
sec/(semi-circle)2
sec/(semi-circle)3
Units
weeks
Value/remark
GPS #1
27
3GPP
Value/remark
GPS #2
230
Value/remark
GPS #3
230
Release 6
114
Satellite Information
Parameter
Units
Number of satellites
Value/remark GPS
All
24
---
Units
---
Value/remark
See file: Almanac XX.csv
Units
---
Value/remark GPS #1
PRNs: 1, 2, 4, 5, 6, 7,
9, 10, 11, 14, 15, 16,
17, 18, 19, 20, 21, 22,
24, 25, 26, 27, 29, 30
Value/remark GPS #2
PRNs: 1, 2, 3, 4, 5, 6,
7, 8, 11, 13, 14, 15, 16,
17, 18, 20, 21, 22, 23,
25, 27, 28, 30, 31
Value/remark GPS #3
PRNs: 1, 2, 3, 4, 5, 6,
7, 8, 11, 13, 14, 15, 16,
17, 18, 20, 21, 22, 23,
25, 27, 28, 30, 31
af0
af1
Units
dimensionless
sec
semi-circles
semi-circles/sec
Boolean
meters1/2
semi-circles
semi-circles
semi-circles
seconds
sec/sec
Value/remark
See file: Almanac XX.csv
See file: Almanac XX.csv
See file: Almanac XX.csv
See file: Almanac XX.csv
See file: Almanac XX.csv
See file: Almanac XX.csv
See file: Almanac XX.csv
See file: Almanac XX.csv
See file: Almanac XX.csv
See file: Almanac XX.csv
See file: Almanac XX.csv
3GPP
Release 6
115
UTRAN GPS
reference time
>UTRAN GPS
timing of cell
frames
>CHOICE mode
Units
msec
Value/remark GPS
#1
51888000 ms. Start
time. Add number of
ms as required.
(Note 1)
Present for
Sensitivity Fine Time
Assistance test case.
Absent otherwise
Note 2
Value/remark GPS
#2
346080000 ms. Start
time. Add number of
ms as required.
(Note 1)
Present for
Sensitivity Fine Time
Assistance test case.
Absent otherwise
Note 2
Value/remark GPS
#3
346080000 ms. Start
time. Add number of
ms as required.
(Note 1)
Absent
Present for
Sensitivity Fine Time
Assistance test case.
Absent otherwise
100
Present for
Sensitivity Fine Time
Assistance test case.
Absent otherwise
100
>>FDD
>>>Primary
CPICH Info
>SFN
Note 2
Note 2
Note 1: GPS TOW msec
This is the value in ms of GPS TOW msec when the GPS scenario is initially started in the GPS
simulator. For all TTFF test cases, each time a GPS scenario is used, the GPS start time shall be
advanced by 120 seconds from the value last used so that, at the time the fix is made, it is at least
2 minutes later than the previous fix made with that scenario.
The actual value of GPS TOW msec to be used in the Acquisition Assistance IE (before the addition
of the random offset, if applicable) shall be calculated at the time the IE is required by adding the
elapsed time since the time the scenario was started in the GPS simulator to this value. The
accuracy shall be such that the Maximum Test System Uncertainty for Coarse Time Assistance,
specified in Table F.1.2 of TS 34.171 [41], shall be met.
For all TTFF test cases a random offset is then added to the value of GPS TOW msec as described
in clause 10.6.2
This final GPS TOW msec value is then also used to determine the value of the Acquisition
Assistance parameters marked as Time varying in clause 10.6.8
Note 2: UTRAN GPS timing of cell frames and SFN
The values of UTRAN GPS timing of cell frames (before the addition of the random offset) and SFN
shall be calculated at the time the IE is required. The accuracy of the relationship between the two
fields shall be such that the Maximum Test System Uncertainty for Fine Time Assistance, specified
in Table F.1.2 of TS 34.171 [41], shall be met.
A random offset is then added to the value of UTRAN GPS timing of cell frames as described in
clause 10.6.2
Satellite Information
Parameter
Number of satellites
Units
---
Value/remark GPS
All
9
Units
---
Value/remark GPS #1
PRNs: 2, 6, 10, 17, 18, 21,
26, 29, 30
Value/remark GPS #2
PRNs: 3, 11, 14, 15, 18, 22,
23, 25, 31
3GPP
Value/remark GPS #3
PRNs: 3, 11, 14, 15, 18, 22,
23, 25, 31
Release 6
116
3GPP
Release 6
117
Units
Value/remark
Ellipsoid point with altitude and uncertainty Ellipsoid
+35.666667
+139.75
+50
3 000
3 000
0
500
68
Bit field
degrees
degrees
m
m
m
degrees
m
%
Units
---
Value/remark
6
Ephemeris and Clock Correction parameters (Fields occurring once per satellite)
Parameter
C/A or P on L2
URA Index
SV Health
IODC
L2 P Data Flag
SF 1 Reserved
TGD
Units
Boolean
Boolean
Boolean
--Boolean
--sec
Value/remark
See file: Navigation model.csv
See file: Navigation model.csv
See file: Navigation model.csv
See file: Navigation model.csv
See file: Navigation model.csv
See file: Navigation model.csv
See file: Navigation model.csv
toc
sec
af2
sec/sec2
af1
sec/sec
3GPP
Release 6
118
af0
sec
Crs
meters
n
M0
semi-circles/sec
semi-circles
Cuc
radians
e
Cus
--radians
(A)1/2
toe
meters1/2
sec
Boolean
sec
radians
OMEGA0
semi-circles
Cis
radians
i0
semi-circles
Crc
meters
OMEGAdot
Idot
semi-circles
semi-circles/sec
semi-circles/sec
Units
seconds
Value/remark
4.6566129 10E-9
sec/semi-circle
1.4901161 10E-8
sec/(semi-circle)2
-5.96046 10E-8
sec/(semi-circle)3
-5.96046 10E-8
seconds
79872
sec/semi-circle
65536
sec/(semi-circle)2
-65536
sec/(semi-circle)3
-393216
Units
Value/remark
weeks
212
Satellite Information
Parameter
Number of Satellites
Units
---
Value/remark
24
Units
-----
3GPP
Value/remark
See file: Almanac.csv
PRNs: 1 to 24
Release 6
119
e
toa
dimensionless
sec
i
OMEGADOT
SV Health
A1/2
OMEGA0
semi-circles
semi-circles/sec
Boolean
meters1/2
semi-circles
M0
semi-circles
af0
semi-circles
seconds
af1
sec/sec
Satellite Information
Parameter
Number of Satellites
Units
---
Value/remark
6
3GPP
Release 6
120
Annex A (informative):
Void
3GPP
Release 6
121
Annex B (informative):
Void
3GPP
Release 6
122
Annex C (normative):
GPS Data Files
C.1
The GPS data files for use in signalling tests defined in 3GPP TS 34.123-1 [1] are contained in archive GPS Data Sig
V2.zip which accompanies the present document.
C.2
The GPS data files for use in performance tests defined in 3GPP TS 34.171 [41]are contained in archive GPS Data Perf
V4.zip which accompanies the present document.
3GPP
Release 6
123
Annex D (informative):
Change history
3GPP
Release 6
Doc-1st-Level
124
Meetin
g-1stLevel
TP-08
TP-09
TP-09
TP-09
TP-09
TP-09
TP-09
TP-09
TP-09
TP-09
TP-09
TP-09
TP-09
TP-09
TP-09
TP-09
TP-09
TP-09
TP-09
CR
TP-000131
TP-000131
TP-000131
TP-000131
TP-000131
TP-000131
TP-000131
TP-000131
TP-000131
TP-000131
TP-000131
TP-000131
TP-000131
TP-000131
TP-000131
TP-000131
TP-000131
TP-000131
001
002
003
004
005
006
007
008
009
010
011
012
013
014
015
016
017
018
TP-09
TP-09
TP-10
TP-10
TP-000131
TP-000131
TP-000215
TP-000215
019
020
021
022
TP-10
TP-10
TP-10
TP-10
TP-000215
TP-000215
TP-000215
TP-000215
023
024
025
026
TP-10
TP-10
TP-000215
TP-000215
027
028
TP-10
TP-10
TP-000215
TP-000215
029
030
TP-10
TP-000215
031
TP-11
TP-11
TP-010018
TP-010018
032
033
TP-11
TP-11
TP-11
TP-11
TP-11
TP-11
TP-12
TP-12
TP-12
TP-010018
TP-010018
TP-010018
TP-010018
TP-010018
TP-010018
TP-010118
TP-010118
TP-010118
034
035
036
037
038
039
040
041
042
TP-12
TP-12
TP-12
TP-12
TP-12
TP-010118
TP-010118
TP-010118
TP-010118
TP-010118
043
044
045
046
047
TP-13
TP-13
TP-13
TP-13
TP-13
TP-010215
TP-010215
TP-010215
TP-010215
TP-010215
048
049
050
051
052
TP-13
TP-13
TP-13
TP-010215
TP-010215
TP-010215
053
054
055
TP-13
TP-010215
056
TP-13
TP-13
TP-010215
TP-010215
057
058
Rev
Subject
Approval of the specification
RRC Message Contents: RLCSize
RRC Message Contents: RLCParam
RRC Message Contents: PCPreamble
RRC Message Contents: RBIdentity
RRC Message Contents: TrCHParam
RRC Message Contents: UECapability
RRC Message Contents: RBMapping
RRC Message Contents: PagingCause
RRC Message Contents: CipheringAndIntegrity
RRC Message Contents: RLCInfo
RRC Message Contents: CompressedMode
RRC Message Contents: SIB
RRC Message Contents: PhyCH
RRC Message Contents: Measurement
RRC Message Contents: TFCS
RRC Message Contents: DPCHFrameOffset
Test USIM Parameters
Correction to definition of the test algorithm for
authentication (clause 8.1.2)
Reference Radio Bearer Configurations
TDD Single mode
Common generic procedure for AS testing
Requirements for the system simulator for support of
Tcell parameter
Minimum Performance Levels
Downlink signal conditions and propagation conditions
Updating 34.108 v3.1.0 to TDD single mode
Application of integrity mode protection to signalling
message by default
Updates to the default message contents in clause 9
Updates to System Information Block (SIB) and Master
Information Block (MIB) messages
Application of ciphering during conformance testing
Addition for System Information parameters (34.108
clause 6.1)
Correction for Generic Setup Procedures (34.108
clause 7.2)
Default radio conditions for multi-cell environment
Correction for Generic Setup Procedures (34.108
clause 7.2)
Corrections for Test USIM Parameters(34.108 clause 8)
Correction of clause number in TS 34.108.
Update of authentication test algorithm
Updates to clause 9 of TS 34.108 v3.2.0
Updating to TDD single mode
Simulated network environments for TDD mode (SIB)
Corrections to clause 6.10 FDD parameters
Corrections to clause 6.10 TDD parameters
Adding section for radio bearer configurations intended
for functional testing
Update of list of abbreviations
Updates to clause 6.1 and 9
Updates to clause 7.4
clause 6.1: System Information Blocks for TDD Mode
Editorial corrections and removal of a reference
document
Correction to reference
Editorial modification for References
Some corrections in clause 5
Update to Scope Statement
Clause 6.10 Definition of RB configurations, TDD
parameters
Updates to clause 6.1, clause 7.4 and clause 9
Clause 6.1: Default radio conditions for Signalling tests
Correction of Radio Bearer Configurations for FDD
Mode
Correction of Radio Bearer Configurations for TDD
Mode
Changes to Signalling Radio Bearer (SRB) numbering
Missing bearers in tables 6.10.2.1.1 and 6.10.3.1.1
3GPP
Doc-2ndLevel
C
C
C
C
C
C
C
C
C
C
C
C
D
C
C
C
F
F
2.0.0
3.0.1
3.0.1
3.0.1
3.0.1
3.0.1
3.0.1
3.0.1
3.0.1
3.0.1
3.0.1
3.0.1
3.0.1
3.0.1
3.0.1
3.0.1
3.0.1
3.0.1
3.0.1
3.0.0
3.1.0
3.1.0
3.1.0
3.1.0
3.1.0
3.1.0
3.1.0
3.1.0
3.1.0
3.1.0
3.1.0
3.1.0
3.1.0
3.1.0
3.1.0
3.1.0
3.1.0
3.1.0
T1-000190
T1-000191
T1-000192
T1-000193
T1-000194
T1-000195
T1-000196
T1-000197
T1-000198
T1-000199
T1-000200
T1-000201
T1-000202
T1-000203
T1-000204
T1-000205
T1-000215
T1-000164
F
F
B
F
3.0.1
3.0.1
3.1.0
3.1.0
3.1.0
3.1.0
3.2.0
3.2.0
T1-000212
T1-000220
T1-000294
T1-000303
F
D
F
F
3.1.0
3.1.0
3.1.0
3.1.0
3.2.0
3.2.0
3.2.0
3.2.0
T1-000306
T1-000307
T1-000281
T1-000296
C
C
3.1.0
3.1.0
3.2.0
3.2.0
T1-000282
T1-000283
C
F
3.1.0
3.1.0
3.2.0
3.2.0
T1-000285
T1-000304
3.1.0
3.2.0
T1-000305
F
F
3.2.0
3.2.0
3.3.0
3.3.0
T1-010078
T1-010079
F
D
C
F
F
F
F
F
D
3.2.0
3.2.0
3.2.0
3.2.0
3.2.0
3.2.0
3.3.0
3.3.0
3.3.0
3.3.0
3.3.0
3.3.0
3.3.0
3.3.0
3.3.0
3.4.0
3.4.0
3.4.0
T1-010080
T1-010081
T1-010082
T1-010084
T1-010088
T1-010089
T1-010205
T1-010206
T1-010210
D
F
F
F
F
3.3.0
3.3.0
3.3.0
3.3.0
3.3.0
3.4.0
3.4.0
3.4.0
3.4.0
3.4.0
T1-010211
T1-010212
T1-010213
T1-010214
T1-010215
F
F
F
F
F
3.4.0
3.4.0
3.4.0
3.4.0
3.4.0
3.5.0
3.5.0
3.5.0
3.5.0
3.5.0
T1-010275
T1-010276
T1-010277
T1-010278
T1-010279
F
F
F
3.4.0
3.4.0
3.4.0
3.5.0
3.5.0
3.5.0
T1-010280
T1-010281
T1-010282
3.4.0
3.5.0
T1-010283
F
F
3.4.0
3.4.0
3.5.0
3.5.0
T1-010284
T1-010285
Release 6
125
Meetin Doc-1st-Level CR
g-1stLevel
TP-13 TP-010215
059
TP-13 TP-010215
060
TP-13
TP-010215
061
TP-13
TP-010215
062
TP-13
TP-14
TP-14
TP-14
TP-14
TP-14
TP-14
TP-010215
TP-010285
TP-010285
TP-010258
TP-010258
TP-010258
TP-010258
063
065
067
069
071
073
075
TP-14
TP-14
TP-14
TP-15
TP-010258
TP-010258
TP-010292
TP-020038
077
079
081
083
TP-15
TP-15
TP-020038
TP-020038
085
087
TP-15
TP-15
TP-15
TP-020038
TP-020038
TP-020038
089
091
094
TP-15
TP-020038
095
Rev
1
1
TP-16
TP-020141
108
TP-16
TP-020141
109
TP-16
TP-020141
110
TP-16
TP-020141
111
TP-16
TP-16
TP-16
TP-16
TP-020141
TP-020141
TP-020141
TP-020141
112
113
114
115
TP-16
TP-16
TP-16
TP-16
TP-020141
TP-020141
TP-020141
TP-020141
116
117
118
119
TP-16
TP-020141
121
TP-17
TP-020184
123
TP-17
TP-17
TP-020184
TP-020184
125
127
TP-17
TP-17
TP-020184
TP-020184
129
131
TP-17
TP-17
TP-020184
TP-020184
133
135
TP-17
TP-020184
137
TP-17
TP-020184
140
TP-17
TP-020184
142
TP-18
TP-18
TP-020293
TP-020293
144
146
Subject
Correction of system information block 5
Introducing of 1.28 Mcps TDD Mode in clauses 4, 5 and
6
Introduction of System Information Blocks for 1.28
Mcps TDD Mode
Introduction of typical radio parameters for 1.28
McpsTDD
Clause 6.11 RBs for RLC and PDCP testing
Correction to 6.1 Contents of System Information Blocks
Corrections to clause 6.1, 7.4 and 9
Reference Radio Conditions
Modification of Test procedures for RF tests
Default message contents for RF tests
Correction to 6.10 Reference Radio Bearer
configurations
Definition of default value of rate matching attribute
Update of clause 7.4 and 6.10
Correction on introduction of clause 6.10
Replacement of Block STTD by Space Code Transmit
Diversity (SCTD) (Rel-4)
Update of reference radio conditions (Rel-4)
Update of system reference configurations and default
messages (Rel-4)
Corrections to 34108-410
Introduction of new Reference RABs (Rel-4)
Update of SIBs for TDD (both modes) in TS 34.108
(Rel4)
Clarification of bit rate of Interactive/Background PS
RAB function (Rel-4)
Correction of CR implementation errors in clauses:
6.10.2.2 and 6.10.2.4.1.58.2.1.1
Clause 7(reference) Update of generic setup
procedures to use 13.6 kbps SRB in RRC connection
establishment TDD (3.84 Mcps and 1.28 Mcps)
Correction to clause 7.3.3.4 RADIO BEARER SETUP
message
Change of RM attribute of DL:3.4 kbps SRBs for DCCH
in for REL4
New additional RAB configuration ( R1-020669) for
REL4
Correction of Puncturing Limit for RABs for REL4
Test USIM
Clause 6.1 (SIBs)Rel 4 (3.84 Mcps and 1.28 Mcps TDD)
Clause 6.10 References for TDD about Clarification of
bit rate of Interactive/Background PS RAB
Correction to default message in clause 9 for Rel4
Correction to clause 6.1 for Rel4
WCDMA1800 additions for Rel4
Clause 9.1 Default message contents for TDD ( 3.84
Mcps and 1.28 Mcps) R4
Update of generic setup procedures to use 13.6 kbps
SRB in RRC connection establishment
Alignment of reference configurations on S-CCPCH with
default system information messages
Addition of reference compressed mode pattern
Corrections to default message contents as T1S020347rev1
Additional default message contents for RF Testing
Corrections related to SIB11, SIB12 and to the
MEASUREMENT CONTROL message
Corrections to clause 6.1 (T1S-020349rev1)
Introduction of reference configurations on S-CCPCH
and PRACH with two interactive PS domain RABs
Removal of reference radio bearer configurations for
unidirectional streaming CS RABa above 64 kbps
Some corrections and updates in clause 6.1 for TDD
mode
Inclusion of default message contents for RF in clause
9.2 for TDD mode
Correction to default messages in 9.1 and 9.2
Corrections in the TDD test frequencies according to
3GPP
Doc-2ndLevel
F
F
3.4.0
3.4.0
3.5.0
4.0.0
T1-010286
T1-010287
3.4.0
4.0.0
T1-010288
3.4.0
4.0.0
T1-010289
F
A
A
A
A
A
A
3.4.0
4.0.0
4.0.0
4.0.0
4.0.0
4.0.0
4.0.0
3.5.0
4.1.0
4.1.0
4.1.0
4.1.0
4.1.0
4.1.0
T1-010290
T1-010475
T1-010473
T1-010461
T1-010463
T1-010465
T1-010467
A
A
A
A
4.0.0
4.0.0
4.0.0
4.1.0
4.1.0
4.1.0
4.1.0
4.2.0
T1-010469
T1-010471
-T1-020092
A
A
4.1.0
4.1.0
4.2.0
4.2.0
T1-020098
T1-020100
A
A
F
4.1.0
4.1.0
4.1.0
4.2.0
4.2.0
4.2.0
T1-020102
T1-020195
T1-020107
4.1.0
4.2.0
T1-020184
4.2.0
4.2.1
4.2.1
4.3.0
T1-020289
4.2.1
4.3.0
T1-020291
4.2.1
4.3.0
T1-020292
4.2.1
4.3.0
T1-020293
A
A
F
A
4.2.1
4.2.1
4.2.1
4.2.1
4.3.0
4.3.0
4.3.0
4.3.0
T1-020294
T1-020295
T1-020296
T1-020297
A
A
A
F
4.2.1
4.2.1
4.2.1
4.2.1
4.3.0
4.3.0
4.3.0
4.3.0
T1-020298
T1-020299
T1-020300
T1-020301
4.2.1
4.3.0
T1-020434
4.3.0
4.4.0
T1-020503
A
A
4.3.0
4.3.0
4.4.0
4.4.0
T1-020505
T1-020507
A
A
4.3.0
4.3.0
4.4.0
4.4.0
T1-020509
T1-020527
A
A
4.3.0
4.3.0
4.4.0
4.4.0
T1-020530
T1-020539
4.3.0
4.4.0
T1-020541
4.3.0
4.4.0
T1-020576
4.3.0
4.4.0
T1-020578
A
A
4.4.0
4.4.0
4.5.0
4.5.0
T1-020658
T1-020674
Release 6
Meetin Doc-1st-Level
g-1stLevel
126
CR
Rev
Subject
core specs
3GPP
Doc-2ndLevel
Release 6
127
Meetin Doc-1st-Level CR
g-1stLevel
TP-18 TP-020293
148
Rev
-
TP-18
TP-18
TP-18
TP-18
TP-020293
TP-020293
TP-020293
TP-020293
150
152
154
156
TP-18
TP-18
TP-020293
TP-020293
158
160
TP-18
TP-18
TP-020293
TP-020293
162
164
TP-18
TP-020293
166
TP-18
TP-020293
168
TP-18
TP-18
TP-020293
TP-020293
169
171
TP-19
TP-19
TP-030044
TP-030044
173
175
TP-19
TP-030044
177
TP-19
TP-030044
179
TP-19
TP-030044
181
TP-19
TP-030044
183
TP-19
TP-030044
185
TP-19
TP-19
TP-19
TP-030044
TP-030044
TP-030044
187
189
191
TP-19
TP-030044
193
TP-19
TP-030044
195
TP-19
TP-030044
197
TP-19
TP-030043
198
TP-19
TP-030043
200
TP-19
TP-030043
202
TP-19
TP-19
TP-030043
TP-030043
204
206
TP-20
TP-030098
208
TP-20
TP-20
TP-030098
TP-030098
210
212
TP-20
TP-030098
214
TP-20
TP-030098
216
TP-20
TP-030098
218
TP-20
TP-20
TP-030098
TP-030098
219
221
TP-20
TP-21
TP-030140
TP-030191
226
228
TP-21
TP-030191
230
Subject
Addition of alternative configuration using Turbo Coding
for Interactive or background / UL:8 DL:8 kbps / PS RAB
+ UL:3.4 DL:3.4 kbps SRBs for DCCH
Correction to content of clause 6.10.2.
Correction to SIB 11/12 definition
Reference Measurement Channels
Transferring system information definition using ASN.1
description to PRD
Correction to RLC RAB TFCS
Default Message contents : Correction from CRs
approved in RP17meeting
Corrections to SIB1 to SIB6
Correction to RAB configurations as revision of
T1S020756
Parameter addition for Reference RABs based on LS
from RAN2
Addition to clause 7.4 for multi call as T1S-020577rev2
(revision to T1S020820)
RAB Combinations for IMS Services
Correction to Contents of the Scheduling Block Syste
Information in clause 6.1.3.
RAB Removal from Rel 4 TS 34.108 as T1S030002rev1
Combine all Radio Bearer Setup messages into one
table
Corrections to SB and SIB configurations in clause 6.1
as T1S030046rev1
Correction to TS 34.108 Rel-4 ; PAGING TYPE1
message (Packet in PS)
Clarification of autentication test algorithm and GSM
cipher key
Addition of simulated network environment for inter-RAT
test cases
Corrections to SIB1 to align with default values for LAC
and RAC in 51.010-1.
Addition of default inter-RAT handover messages
Correction of activation time IEs in default messages
Correction to default SECURITY MODE COMMAND
message
Addition of option for UL CM only in default reference
CM patterns
Introduction of a reference RB configuration for RMC for
BTFD tests (Rel4)
Update of the RRC connection request messages in
34.108 Rel4
Introduction of Conversational PS RABs in Rel 4 TS
34.108 as T1S030003rev1
Update of default parameters for 1 to 8 cell
environments (TDD), clause 6.1.4, Rel 4
Update of Multi-cell environment for default radio
conditions (TDD), clause 6.1.6 (Inclusion of cell 4), Rel 4
Modification to Generic Registration Procedures
Update of default configurations to enable testing of low
end UE
Reinstate parameters for Interactive or background
/UL:64 kbps / PS RAB
Correction to Figure 7.4.1.1 (Rel-4)
Update of SIB 11 and 12 in clause 6.1.0b in TS 34.108
(TDD)
Update of Default parameters for 1 to 8 cell
environments in TS 34.108 (TDD)
Correction of default messages according to 25331
CR1823
Clause 8.2: Definition of default values for
authentication key K on test USIM
Update of Reconfiguration messages
Correction to RADIO BEARER RELEASE and RRC
CONNECTION SETUP messages (Revision of T1030569)
Correction to default SIB5 (FDD)
CR to 34.108, Rel-4, Clarification of seg_count in
6.1.0a.3
General correction in clause 7.4 for Common generic
3GPP
Doc-2ndLevel
4.4.0
4.5.0
T1-020694
A
A
A
A
4.4.0
4.4.0
4.4.0
4.4.0
4.5.0
4.5.0
4.5.0
4.5.0
T1-020709
T1-020712
T1-020768
T1-020778
A
A
4.4.0
4.4.0
4.5.0
4.5.0
T1-020780
T1-020783
A
A
4.4.0
4.4.0
4.5.0
4.5.0
T1-020799
T1-020801
4.4.0
4.5.0
T1-020803
4.4.0
4.5.0
T1-020818
F
F
4.4.0
4.4.0
4.5.0
4.5.0
T1-020819
T1-020844
A
A
4.5.0
4.5.0
4.6.0
4.6.0
T1-030037
T1-030040
4.5.0
4.6.0
T1-030042
4.5.0
4.6.0
T1-030044
4.5.0
4.6.0
T1-030046
4.5.0
4.6.0
T1-030048
4.5.0
4.6.0
T1-030050
A
A
A
4.5.0
4.5.0
4.5.0
4.6.0
4.6.0
4.6.0
T1-030052
T1-030054
T1-030056
4.5.0
4.6.0
T1-030058
4.5.0
4.6.0
T1-030060
4.5.0
4.6.0
T1-030063
4.5.0
4.6.0
T1-030107
4.5.0
4.6.0
T1-030208
4.5.0
4.6.0
T1-030210
A
A
4.5.0
4.5.0
4.6.0
4.6.0
T1-030222
T1-030228
4.6.0
4.7.0
T1-030437
A
A
4.6.0
4.6.0
4.7.0
4.7.0
T1-030483
T1-030507
4.6.0
4.7.0
T1-030509
4.6.0
4.7.0
T1-030632
4.6.0
4.7.0
T1-030644
A
A
4.6.0
4.6.0
4.7.0
4.7.0
T1-030692
T1-030699
A
A
4.6.0.
4.7.0
4.7.0
4.8.0
T1-030745
T1-030827
4.7.0
4.8.0
T1-030976
Release 6
Meetin Doc-1st-Level
g-1stLevel
128
CR
Rev
Subject
procedures for AS testing
3GPP
Doc-2ndLevel
Release 6
Doc-1st-Level
129
Meetin
g-1stLevel
TP-21
TP-21
TP-21
CR
Rev
TP-030191
TP-030191
TP-030191
233
235
237
TP-21
TP-21
TP-030191
TP-030191
239
242
TP-21
TP-030191
244
TP-21
TP-030191
246
TP-21
TP-030191
248
TP-21
TP-030191
240
TP-22
TP-22
TP-22
TP-22
TP-22
TP-22
TP-22
TP-22
TP-22
TP-030279
TP-030279
TP-030279
TP-030279
TP-030279
TP-030279
TP-030279
TP-030279
TP-030279
251
252
253
254
255
256
257
258
260
1
1
1
1
1
1
1
1
2
TP-22
TP-030279
262
TP-22
TP-030279
264
TP-22
TP-030279
266
TP-22
TP-22
TP-030279
TP-030279
268
269
TP-22
TP-030279
271
TP-22
TP-030279
273
TP-22
TP-22
TP-030279
TP-030279
275
277
1
1
TP-22
TP-22
TP-030279
TP-030279
279
283
TP-23
TP-040037
284
TP-23
TP-040037
287
TP-23
TP-040037
289
TP-23
TP-23
TP-040037
TP-040037
291
296
TP-23
TP-040037
298
TP-23
TP-040037
300
TP-23
TP-040037
302
TP-23
TP-040037
303
TP-23
TP-040037
304
TP-23
TP-040037
305
TP-23
TP-23
TP-040037
TP-040037
292
294
Subject
Incorrect activation time in CELL_FACH state .
Incorrect Transport channel Parameters
Corrections to TS 34.108 common procedures in clause
7.4 of Rel-4 of TS 34.108
Removal of RLC AM in the Default Message Content
CR 34.108 Rel-4: Manual attach in State 7 Registrated
Idle Mode on CS/PS
URA Identity in Cell Update Confirm and URA Update
Confirm
CR to 34.108 R4; Correction to specification to reflect a
change already approved in TTCN CR T1-030396
CR to 34.108 REL-4; Correction to clause 7.3 Test
procedures for RF test
RB configuration for the support of wideband AMR
speech telephony services
Addition of Default message contents for TDD
Addition of Default message contents for TDD
Addition of Default message contents for TDD
Addition of Default message contents for TDD
Addition of Default message contents for TDD
Addition of Default message contents for TDD
Addition of Default message contents for TDD
Addition of Default message contents for TDD
CR on PAGING TYPE 1, RRC CONNECTION
REQUEST and RRC CONNECTION SETUP messages
for MT RR Connection
CR 34.108 Rel-4: EFRPLMNACT (RPLMN Last used
Access Technology) removed
Update of default messages for RRC CONNECTION
SETUP and SECURITY MODE COMMAND
Description and corrections of channels for minimum
performance levels, TDD mode.
Test frequencies of UMTS800MHz band VI
CR 34.108 Rel-4: Addition of Bearer combination for
Interactive/background UL 64 kbps DL 768 kbps for Rel5
Update of generic test procedure for TX, RX and
Performance Requirement
Introduction of generic test procedure for RRM
handover test cases
Correction of CM TGD parameter
Corrections to default message contents of Radio
Bearer Release
Modification to default DPCCH_Power_offset value
Correction of TFCS for radio bearer combination
6.10.2.4.1.51b
New Radio Bearer Setup (FDD) message for RF
(Revision of T1-040258)
Corrections to default message contents of RRC
Connection Setup message -> 2nd change not
implemented (not implementable)
Correction to Default parameters for Cells 1 to 8 in
MultiPLMN cell environments - Rel-4
Corrections to TDD HCR RABs
LCR Corrections to TDD RABs merge of T1-040104 ,
T1-040201 and T1-040203
Correction to handling of Entered Parameter IE in
default contents for Initial Direct Transfer
The diverse operation in TDD mode updating according
to the core specification
correction of measurement control default message
contents for TDD -> Not implemented (not
implementable)
correction of RADIO BEARER SETUP default message
contents for 1.28 Mcps TDD
Correction of RADIO BEARER RELEASE default
message contents for TDD: AM or UM (1.28 Mcps TDD)
Contents of RRC CONNECTION SETUP message: UM
(Transition to CELL_DCH) (1.28 Mcps TDD) -> Not
implemented (not implementable)
New I/B UL:64 DL:768 kbps PS RAB misplaced
Generic setup procedure and default message contents
3GPP
Doc-2ndLevel
A
A
A
4.7.0
4.7.0
4.7.0
4.8.0
4.8.0
4.8.0
T1-031064
T1-031066
T1-031095
A
A
4.7.0
4.7.0
4.8.0
4.8.0
T1-031151
T1-031175
4.7.0
4.8.0
T1-031179
4.7.0
4.8.0
T1-031241
4.7.0
4.8.0
T1-031251
4.7.0
4.8.0
T1-031154
F
F
F
F
F
F
F
F
A
4.8.0
4.8.0
4.8.0
4.8.0
4.8.0
4.8.0
4.8.0
4.8.0
4.8.0
4.9.0
4.9.0
4.9.0
4.9.0
4.9.0
4.9.0
4.9.0
4.9.0
4.9.0
T1-031659
T1-031660
T1-031661
T1-031662
T1-031663
T1-031664
T1-031665
T1-031666
T1-031596
4.8.0
4.9.0
T1-031381
4.8.0
4.9.0
T1-031547
4.8.0
4.9.0
T1-031645
A
F
4.8.0
4.8.0
4.9.0
4.9.0
T1-031555
T1-031441
4.8.0
4.9.0
T1-031610
4.8.0
4.9.0
T1-031608
A
F
4.8.0
4.8.0
4.9.0
4.9.0
T1-031591
T1-031594
A
A
4.8.0
4.8.0
4.9.0
4.9.0
T1-031598
T1-031527
4.9.0
4.10.0
T1-040417
4.9.0
4.10.0
T1-040080
4.9.0
4.10.0
T1-040095
A
F
4.9.0
4.9.0
4.10.0
4.10.0
T1-040103
T1-040299
4.9.0
4.10.0
T1-040411
4.9.0
4.10.0
T1-040368
4.9.0
4.10.0
T1-040370
4.9.0
4.10.0
T1-040371
4.9.0
4.10.0
T1-040372
4.9.0
4.10.0
T1-040373
F
F
4.10.0
4.10.0
5.0.0
5.0.0
T1-040109
T1-040271
Release 6
Meetin Doc-1st-Level
g-1stLevel
130
CR
Rev
Subject
for HSDPA (as of T1-040069rev1)
3GPP
Doc-2ndLevel
Release 6
131
Meetin Doc-1st-Level CR
g-1stLevel
TP-23 TP-040037
295
TP-24 TP-040112
308
Rev
-
TP-24
TP-040112
309
TP-24
TP-24
TP-24
TP-24
TP-040112
TP-040112
TP-040112
TP-040112
310
315
318
319
TP-24
TP-040112
320
TP-24
TP-040112
325
TP-24
TP-040112
326
TP-24
TP-040112
327
TP-24
TP-24
TP-040112
TP-040112
330
331
TP-24
TP-040112
332
TP-24
TP-040112
333
TP-24
TP-040112
335
TP-24
TP-040112
338
TP-24
TP-25
TP-25
TP-25
TP-040112
TP-040157
TP-040157
TP-040157
339
343
344
345
TP-25
TP-040157
346
TP-25
TP-040157
347
TP-25
TP-25
TP-25
TP-25
TP-25
TP-040157
TP-040157
TP-040157
TP-040157
TP-040157
348
349
350
351
352
TP-25
TP-040157
353
TP-25
TP-040157
354
TP-25
TP-040157
355
TP-25
TP-040157
340
TP-25
TP-040157
361
TP-25
TP-25
TP-040157
TP-040157
362
341
TP-25
TP-25
TP-040157
TP-040157
363
342
TP-25
TP-25
TP-040157
TP-040157
356
357
TP-25
TP-040157
358
TP-25
TP-040157
359
TP-25
TP-040157
360
TP-25
TP-040157
364
Subject
Baseline radio bearer combination for HSDPA support
Correction to IEs "START" and
"ul_CounterSynchronisationInfo".
Correction to HSDPA reference radio bearer
configurations
Addition of test procedure for HSDPA RF testing
Corrections to default RRC messages
Change of default LAC/RAC for inter-RAT test cases
Contents of Physical channel Reconfiguration message
modified to incorporate transition to URA_PCH or
CELL_PCH
Correction of reference test frequencies for
UMTS800(band VI)
Update of generic setup procedures in clauses 7.3.4
and 7.3.5.
Physical channel parameters for AM RLC 7 bit Length
Indicator TestCases (Rel-5)
Corrections to the default contents of Security Mode
Command (Rel-5)
Corrections to Contents of Scheduling Block 1 (FDD)
Corrections to Contents of PHYSICAL CHANNEL
RECONFIGURATION message: AM or UM
Corrections to Contents of RRC CONNECTION SETUP
message: UM
RADIO BEARER SETUP message (FDD) for Test Loop
Mode2.
Changes to establish one version of 34.108 covering all
releases
Addition of generic test procedure for AS test cases
using the test loop
Corrections to LCR TDD RABs
Correction to generic test procedure in clause 7.4.2.6a.
Addition of default messages for Signalling (FDD)
Minor change to terminology in SRB tables of clause
6.10
Default Message Content for System Information Block
type 5 (FDD) and type 6 (FDD)
Corrections to DCCH Transport channel Parameters for
HSDPA RAB
Corrections to clause 9
Corrections to HCR TDD RAB combinations
Adding missing clause 6.10.2.4.1.62.1
Modification of AICH power offset in SysInfo 5 and 6.
Correction to Default Message Content for Radio Bearer
Setup Message.
Correction to Default Message Content for Radio Bearer
Reconfiguration Message for Condition A6
CR to 34.108: introduction of default RB SETUP
message from cell_FACH state for HSDPA
Corrections to Contents of RADIO BEARER SETUP
message: BTFD RMC
Resolution of downlink code conflict between OCNS
DPCH and S-CCPCH
Correction to test procedure for test cases using
Cell_PCH or URA_PCH state
Removal of DCCH dummy transmission for RF testing
Correct title to test procedure for test cases using
Cell_PCH or URA_PCH state
Addition of intra frequency cell to cell environments
Correct primary scrambling code usage in default
message contents in clause 9.2.1
HSDPA downlink code allocation
Correction to test procedure for test cases using
CELL_FACH state
Varying DPCH Power Offset according to data
transmission rate
Corrections to default message for RADIO BEARER
SETUP message in clause 9.2.1 (HSDPA RF)
Test SIB schedule for two S-CCPCH or two PRACH in
34.108
Correction to Default Message Content for Radio Bearer
Setup Message re: RM Attribute values
3GPP
Doc-2ndLevel
B
F
4.10.0
5.0.0
5.0.0
5.1.0
T1-040273
T1-040512
5.0.0
5.1.0
T1-040522
F
F
A
F
5.0.0
5.0.0
5.0.0
5.0.0
5.1.0
5.1.0
5.1.0
5.1.0
T1-040546
T1-040593
T1-040656
T1-040673
5.0.0
5.1.0
T1-040701
5.0.0
5.1.0
T1-040754
5.0.0
5.1.0
T1-040902
5.0.0
5.1.0
T1-040903
F
F
5.0.0
5.0.0
5.1.0
5.1.0
T1-040909
T1-040911
5.0.0
5.1.0
T1-040913
5.0.0
5.1.0
T1-040917
5.0.0
5.1.0
T1-040931
5.0.0
5.1.0
T1-040934
F
F
F
F
5.0.0
5.1.0
5.1.0
5.1.0
5.1.0
5.2.0
5.2.0
5.2.0
T1-040935
T1-041040
T1-041044
T1-041140
5.1.0
5.2.0
T1-041154
5.1.0
5.2.0
T1-041171
F
F
F
F
F
5.1.0
5.1.0
5.1.0
5.1.0
5.1.0
5.2.0
5.2.0
5.2.0
5.2.0
5.2.0
T1-041223
T1-041235
T1-041252
T1-041253
T1-041259
5.1.0
5.2.0
T1-041266
5.1.0
5.2.0
T1-041298
5.1.0
5.2.0
T1-041317
5.1.0
5.2.0
T1-041327
5.1.0
5.2.0
T1-041346
F
F
5.1.0
5.1.0
5.2.0
5.2.0
T1-041350
T1-041354
F
F
5.1.0
5.1.0
5.2.0
5.2.0
T1-041356
T1-041365
F
F
5.1.0
5.1.0
5.2.0
5.2.0
T1-041374
T1-041376
5.1.0
5.2.0
T1-041416
5.1.0
5.2.0
T1-041418
5.1.0
5.2.0
T1-041422
5.1.0
5.2.0
T1-041433
Release 6
132
Meetin Doc-1st-Level CR
g-1stLevel
TP-26 TP-040233
365
Rev
-
TP-26
TP-040233
366
TP-26
TP-26
TP-040233
TP-040233
367
368
TP-26
TP-040233
369
TP-26
TP-040233
370
TP-26
TP-040233
371
TP-26
TP-040233
372
TP-26
TP-040233
373
TP-26
TP-040233
374
TP-26
TP-26
TP-040233
TP-040233
375
376
TP-26
TP-26
TP-040233
TP-040233
377
378
TP-26
TP-040233
379
TP-26
TP-040233
380
TP-26
TP-040233
381
TP-27
TP-27
TP-27
TP-050032
TP-050032
TP-050032
382
383
384
TP-27
TP-27
TP-050032
TP-050032
385
386
TP-27
TP-050032
387
TP-27
TP-050032
388
TP-27
TP-050032
389
TP-27
TP-050032
390
TP-27
TP-050032
391
TP-27
TP-050032
392
TP-27
TP-050032
393
TP-27
TP-050032
394
TP-27
TP-050032
395
TP-27
TP-27
TP-050032
TP-050032
396
397
TP-27
TP-050032
398
RP-28
RP-050267
399
RP-28
RP-050267
400
RP-28
RP-050267
401
RP-28
RP-050267
402
Subject
CR to 34.108 Rel-5:Correction to default value of
Qrxlevmin
CR to 34.108 Rel-5: Corrections of the values in
6.11.5.4 for LCR TDD
Alignment of Prose to TTCN for SCH power level
Addition of new HSDPA RAB configurations with UL 64
kbps
Correction to initial conditions and references in clause
7.3
Introduction of reference radio bearer combination for
PS streaming and downlink rate up to 128 kbps
Correction of clause 6.1 (Simulated network
environment)
Correction to generic Call Setup procedure for mobile
terminating circuit switched calls
CR to 34.108 Rel-5; Corrections to the default RADIO
BEARER SETUP message for HSDPA
Physical layer multiplexing configuration in case of AMR
and two PS RABs
Addition of new HSDPA RAB configurations
Introduction of information for tests for Performance
requirements for A-GPS.
Introduction of UMTS-850 MHz band V
CR to TS 34.108 Rel-5; Adding a new test condition for
RADIO BEARER RELEASE Procedure (Revision of T1041716).
Update of Reference Radio Bearer for Conversational /
speech / UL:5.9 DL:5.9 kbps / CS RAB for DL SF=256
CR to 34.108: Correction to the maximum bit rate for
HS-PDSCH
Alignment of Prose to TTCN for RRC Connection
Release (Cell DCH state) and RRC Connection Setup
Message (Cell FACH State).
Updates from core specification changes
Correction to Hand over test procedure in CELL_DCH
CR to 34.108: Changes to test frequencies for UMTS
850 Band
Correction to default SIB configurations
Editorial corrections in HSDPA RAB configurations
6.10.2.4.5.2 and 6.10.2.4.5.4.
CR to 34.108 Rel-5: Update to the contents of
PHYSICAL CHANNEL RECONFIGURATION message
for 1.28 Mcps TDD
CR to 34.108 Rel-5: Update to the contents of
TRANSPORT CHANNEL RECONFIGURATION
message for 1.28 Mcps TDD
CR to 34.108 Rel-5: Update to the contents of RRC
CONNECTION REQUEST message for TDD
Correction to the HSDPA RB Identity in Radio Bearer
Setup & Radio Bearer Release message contents
CR to TS 34.108 v5.3.0 - Correction to Default RADIO
BEARER RELEASE message (FDD)
Addition of reference radio bearer configuration for
MAC-hs testing
CR to 34.108 Rel-5: Update to the contents of RRC
CONNECTION REQUEST message for TDD
CR to 34.108 Rel-5: Update to the contents of Default
System Information Block Messages for TDD
CR to 34.108 Rel-5: Add the contents of SIB 5 & 6 for
HCR TDD
Correction to TFCS ordering
Addition of GPS scenario and A-GPS assistance data
values for signalling tests to 34.108
CR to TS 34.108 Rel-5; Correction to the physical
channel parameters (Revison of T1-050176)
Additional call setup procedures for inter RAT RRM
testing
CR to 34.108: Correction to RADIO BEARER SETUP
message for BTFD RMC
CR to 34.108: Correction to reference radio conditions
for GSM
Addition of RADIO BEARER SETUP Messages for
3GPP
Doc-2ndLevel
5.2.0
5.3.0
T1-041532
5.2.0
5.3.0
T1-041573
F
F
5.2.0
5.2.0
5.3.0
5.3.0
T1-041584
T1-041651
5.2.0
5.3.0
T1-041654
5.2.0
5.3.0
T1-041685
5.2.0
5.3.0
T1-041686
5.2.0
5.3.0
T1-041699
5.2.0
5.3.0
T1-041754
5.2.0
5.3.0
T1-041801
F
B
5.2.0
5.2.0
5.3.0
5.3.0
T1-041802
T1-041850
F
F
5.2.0
5.2.0
5.3.0
5.3.0
T1-041874
T1-041933
5.2.0
5.3.0
T1-041942
5.2.0
5.3.0
T1-041943
5.2.0
5.3.0
T1-041965
F
F
B
5.3.0
5.3.0
5.3.0
5.4.0
5.4.0
5.4.0
T1-050095
T1-050350
T1-050380
F
D
5.3.0
5.3.0
5.4.0
5.4.0
T1-050019
T1-050052
5.3.0
5.4.0
T1-050064
5.3.0
5.4.0
T1-050065
5.3.0
5.4.0
T1-050066
5.3.0
5.4.0
T1-050072
5.3.0
5.4.0
T1-050202
5.3.0
5.4.0
T1-050239
5.3.0
5.4.0
T1-050295
5.3.0
5.4.0
T1-050296
5.3.0
5.4.0
T1-050297
F
F
5.3.0
5.3.0
5.4.0
5.4.0
T1-050451r1
T1-050458
5.3.0
5.4.0
T1-050469
5.4.0
5.5.0
R5-050618
5.4.0
5.5.0
R5-050704
5.4.0
5.5.0
R5-050811
5.4.0
5.5.0
R5-050856
Release 6
Meetin Doc-1st-Level
g-1stLevel
133
CR
Rev
Subject
Auxiliary Measurement
3GPP
Doc-2ndLevel
Release 6
134
Meetin Doc-1st-Level CR
g-1stLevel
RP-28 RP-050267
404
Rev
-
RP-28
RP-050267
405
RP-28
RP-28
RP-050267
RP-050267
406
407
RP-28
RP-050267
408
RP-28
RP-050267
409
RP-28
RP-050267
410
RP-28
RP-050267
411
RP-28
RP-28
RP-050267
RP-050267
412
413
RP-28
RP-28
RP-050267
RP-050267
414
415
RP-28
RP-28
RP-050267
RP-050267
416
417
RP-28
RP-050267
418
RP-28
RP-28
RP-050268
RP-050268
419
420
RP-28
RP-050268
421
RP-28
RP-050268
422
RP-28
RP-050268
423
RP-28
RP-050268
424
RP-28
RP-050268
425
RP-28
RP-050268
426
RP-28
RP-050268
427
RP-28
RP-050268
428
RP-28
RP-050268
430
RP-28
RP-050349
403
RP-28
RP-29
RP-050350
RP-050600
429
431
RP-29
RP-29
RP-050600
RP-050600
432
433
RP-29
RP-050600
434
RP-29
RP-050600
435
RP-29
RP-050600
436
RP-29
RP-050600
437
Subject
CR 34.108 Addition of specific message content to AGPS performance test procedures in clause 7.5
CR to 34.108 Rel-5: Clarification of generic setup
procedures in section 7.3.4
Removal of TGPL2
Addition of compressed mode pattern for Inter
Frequency FDD measurement & Inter RAT
measurement GSM
Correction to MIB, PLMN and Cell Value Tag Value
Definition to 34.108
CR to 34.108 Rel-5: Corrections to the contents of
System Information Block type 11 (3.84 Mcps and 1.28
Mcps TDD) in section 6.1.0b
CR to 34.108 Rel-5: Corrections to the usage of Cell
info IE in System Information Block type 11 in section
6.1.4 for TDD cell
CR to 34.108 Rel-5: Corrections to the contents of
System Information Block type 5 (1.28 Mcps TDD)
Update to clause 8 Test USIM Parameters
CR to 34.108 Rel-5: Update of SIB3, SIB4, SIB11 and
SIB12 for TDD in section 6.1.0b
CR to 34.108: Correction to TFCS
CR to TS34.108 Rel-5; Correction to the physical
channel parameter
Correction to default SIB configurations
CR to 34.108: Missing Rel-5 IEs in the default Radio
Bearer Setup message at section 9.1.1.
CR to TS34.108 Rel-5; Clarification of the reference
TFCS for three RB multiplexing option (condition A9)
Addition of new HSDPA Streaming RAB configurations
CR to 34.108 Rel-5: Content Correction of RRC
CONNECTION SETUP message for LCR TDD in 9.1.2
Add Default RADIO BEARER RELEASE message (3.84
Mcps TDD)
Add Default Contents of RADIO BEARER
RECONFIGURATION COMPLETE message: AM (3.84
Mcps TDD)
Add Default Contents of RADIO BEARER
RECONFIGURATION message: AM or UM (3.84 Mcps
TDD)
Add Default Contents of PHYSICAL CHANNEL
RECONFIGURATION message: AM or UM (3.84 Mcps
TDD)
Add Default Contents of PHYSICAL CHANNEL
RECONFIGURATION COMPLETE message: AM (3.84
Mcps TDD)
Add Default Contents of TRANSPORT CHANNEL
RECONFIGURATION message: AM or UM (3.84 Mcps
TDD)
Add Default Contents of TRANSPORT CHANNEL
RECONFIGURATION COMPLETE message: AM (3.84
Mcps TDD)
Add Default Contents of MEASUREMENT REPORT
message: AM (intra/inter-frequency measurement (3.84
Mcps TDD)
Correction to RADIO BEARER SETUP message for
HSDPA RF testing
Addition of GPS scenario and assistance data for AGPS performance tests in 34.108
Corrections to section 10.7 and GPS data file for 34.108
Feature Clean Up: Removal of DRAC from section 9 of
34.108
Feature Clean Up: Removal of SSDT from 34.108
Feature Clean Up: Removal of 80 ms TTI for DCH for all
cases except when the UE supports SF512 from 34.108
Feature Clean Up: Removal of CPCH from section 4 of
34.108
Feature Clean Up: Removal of CPCH from section 6 of
34.108
Feature Clean Up: Removal of CPCH from section 7 & 8
of 34.108
Feature Clean Up: Removal of CPCH from section 9 of
3GPP
Doc-2ndLevel
5.4.0
5.5.0
R5-050709
5.4.0
5.5.0
R5-050663
F
F
5.4.0
5.4.0
5.5.0
5.5.0
R5-050513
R5-050525
5.4.0
5.5.0
R5-050608
5.4.0
5.5.0
R5-050613
5.4.0
5.5.0
R5-050619
5.4.0
5.5.0
R5-050620
F
F
5.4.0
5.4.0
5.5.0
5.5.0
R5-050638
R5-050662
F
F
5.4.0
5.4.0
5.5.0
5.5.0
R5-050677
R5-050724
F
F
5.4.0
5.4.0
5.5.0
5.5.0
R5-050947
R5-050600
5.4.0
5.5.0
R5-050913
F
F
5.4.0
5.4.0
5.5.0
5.5.0
R5-050880
R5-050585
5.4.0
5.5.0
R5-050680
5.4.0
5.5.0
R5-050681
5.4.0
5.5.0
R5-050682
5.4.0
5.5.0
R5-050683
5.4.0
5.5.0
R5-050684
5.4.0
5.5.0
R5-050685
5.4.0
5.5.0
R5-050686
5.4.0
5.5.0
R5-050956
5.4.0
5.5.0
R5-050879
5.4.0
5.5.0
R5-050836
F
F
5.4.0
5.5.0
5.5.0
6.0.0
R5-050969
R5-051312
F
F
5.5.0
5.5.0
6.0.0
6.0.0
R5-051356
R5-051379
5.5.0
6.0.0
R5-051543
5.5.0
6.0.0
R5-051544
5.5.0
6.0.0
R5-051545
5.5.0
6.0.0
R5-051546
Release 6
Meetin Doc-1st-Level
g-1stLevel
135
CR
Rev
Subject
34.108
3GPP
Doc-2ndLevel
Release 6
136
Meetin Doc-1st-Level CR
g-1stLevel
RP-29 RP-050600
438
Rev
-
RP-29
RP-050600
439
RP-29
RP-050600
440
RP-29
RP-050600
441
RP-29
RP-050512
442
RP-29
RP-050514
443
RP-29
RP-050514
444
RP-29
RP-050514
445
RP-29
RP-050514
446
RP-29
RP-050514
447
RP-29
RP-050600
448
RP-29
RP-050600
449
RP-29
RP-050600
450
RP-29
RP-29
RP-050600
RP-050600
451
452
RP-29
RP-050600
453
RP-29
RP-050515
454
RP-29
RP-050600
455
RP-29
RP-050600
456
RP-29
RP-050513
457
RP-29
RP-050600
458
RP-29
RP-050600
459
RP-29
RP-050600
460
RP-30
RP-050767
461
RP-30
RP-050720
462
RP-30
RP-30
RP-30
RP-050716
RP-050769
RP-050769
463
464
465
RP-30
RP-30
RP-050780
RP-050767
466
467
RP-30
RP-050767
468
RP-30
RP-050717
469
RP-30
RP-050716
470
RP-30
RP-050716
471
Subject
Feature Clean Up: Removal of DSCH ( FDD mode) from
34.108
Modification to PS setup procedure for inter RAT RRM
testing
CR to 34.108: RRC CONNECTION SETUP exception
for HSDPA testing
CR to 34.108: Correction to the RADIO BEARER
SETUP message for HSDPA testing
Changes to GPS Scenarios and Assistance data in TS
34.108
CR to 34.108 Rel-5: Correction of contents of RADIO
BEARER SETUP message: AM or UM (1.28 Mcps TDD)
in 9.2.2
CR to 34.108 Rel-5: SIB default schedule in 6.1.0a Default Master Information Block and Scheduling Block
messages
CR to 34.108 Rel-5: Corrections to the IEMidamble
shift and burst type of System Information Block type
5/6 (3.84Mcps TDD) in section 6.1.0b
CR to 34.108 Rel-5: Corrections to the contents of
System Information Block type 5 (3.84 Mcps TDD) in
section 6.1.1
CR to 34.108 Rel-5: Corrections to the value of
Sintrasearch and Sintersearch in Cell selection and
reselection quality measure of System Information
Block type 3/4 (1.28Mcps TDD and 3.84Mcps TDD) in
section 6.1.0b
Use Same as UL for the Added or Reconfigured DL
TrCH information of the added or reconfigured PS RAB
Correction to the default contents for Radio Bearer
Setup message
Corrections to default parameters of UL:384kbps PS
Bearer
Correction to NB AMR Radio Bearer Configurations
Correction to default contents of Cell Update and Initial
Direct transfer message for Rel-5
Correction to DPCCH Power Offset IE in default
contents for RRC Connection Setup and Radio Bearer
Setup message
Using Test USIM for VSTK generation of VGCS/VBS
ciphering
Correction to default contents of RADIO BEARER
SETUP MESSAGE for the IE Number of Processes
Correction of DL channelisation code in RADIO
BEARER SETUP for HSDPA configurations
Clarifiation of reference radio bearer configuration for
MAC-hs test case 7.1.5.2.
Replacement of the technical content of 34.108 Rel-5 by
a pointer to Rel-6 document
Introduction of HSDPA + Wideband AMR radio bearer
combination
Feature Clean Up: Removal of DRAC from section 6 of
34.108
Correction to 34.108: RF Radio Bearer setup message
for HSDPA testing
Changes, additions and corrections to GPS scenarios
and assistance data in TS 34.108
Generic test procedure for EDCH RF testing
Correction of UE test states for RF testing.
Removal of temporary BLER measurement
configuration
Introduction of UMTS1700 for TS34.108
Re-definition of reference radio bearer configuration for
MAC-hs test case 7.1.5.2
Introduction of additional HSDPA radio bearer
combination
CR to 34.108; Correction to default message content in
INITIAL DIRECT TRANSFER
CR to 34.108 Rel-6; Generic Setup Procedure and
Default RRC Messages for Enhanced Uplink Tests
Generic reference bearer radio configurations for EDCH testing
3GPP
Doc-2ndLevel
5.5.0
6.0.0
R5-051548
5.5.0
6.0.0
R5-051161
5.5.0
6.0.0
R5-051430
5.5.0
6.0.0
R5-051112
5.5.0
6.0.0
R5-051076
5.5.0
6.0.0
R5-051212
5.5.0
6.0.0
R5-051213
5.5.0
6.0.0
R5-051222
5.5.0
6.0.0
R5-051344
5.5.0
6.0.0
R5-051536
5.5.0
6.0.0
R5-051041
5.5.0
6.0.0
R5-051044
5.5.0
6.0.0
R5-051058
F
F
5.5.0
5.5.0
6.0.0
6.0.0
R5-051318
R5-051325
5.5.0
6.0.0
R5-051365
5.5.0
6.0.0
R5-051553
5.5.0
6.0.0
R5-051324
5.5.0
6.0.0
R5-051345
5.5.0
6.0.0
R5-051164
5.5.0
6.0.0
R5-051584
5.5.0
6.0.0
R5-051588
5.5.0
6.0.0
R5-051311
6.0.0
6.1.0
R5-052320
6.0.0
6.1.0
R5-052017
F
F
F
6.0.0
6.0.0
6.0.0
6.1.0
6.1.0
6.1.0
R5-052345
R5-052302
R5-051933
B
F
6.0.0
6.0.0
6.1.0
6.1.0
R5-052329
R5-051857
6.0.0
6.1.0
R5-052159
6.0.0
6.1.0
R5-052179
6.0.0
6.1.0
R5-052192
6.0.0
6.1.0
R5-052167
Release 6
137
Meetin Doc-1st-Level CR
g-1stLevel
RP-30 RP-050716
472
Rev
-
RP-30
RP-050718
473
RP-30
RP-30
RP-050769
RP-050769
474
475
RP-30
RP-050769
476
RP-30
RP-050769
477
RP-30
RP-050769
478
RP-30
RP-050769
479
RP-30
RP-30
RP-050776
RP-050769
480
481
RP-30
RP-050769
482
RP-30
RP-050777
483
RP-30
RP-050833
484
RP-30
RP-050832
485
RP-31
RP-31
RP-31
RP-060154
RP-060163
RP-060144
486
487
488
RP-31
RP-060150
489
RP-31
RP-31
RP-060154
RP-060163
490
491
RP-31
RP-060144
492
RP-31
RP-060154
493
RP-31
RP-060153
494
RP-31
RP-31
RP-31
RP-31
RP-060154
RP-060144
RP-060144
RP-060166
495
496
497
498
RP-31
RP-31
RP-060154
RP-060163
499
500
RP-32
RP-060331
501
RP-32
RP-32
RP-32
RP-060331
RP-060331
RP-060337
502
503
504
RP-32
RP-32
RP-060337
RP-060337
505
506
RP-32
RP-060338
507
RP-32
RP-32
RP-060332
RP-060334
508
509
RP-32
RP-060 336
510
RP-32
RP-060337
511
Subject
Addition of basic radio bearer combinations for E-DCH
testing
CR to TS34.108; Correction to the default system
information block type3 for DSAC
Editorial corrections to TS 34.108
Removal of deprecated values from the default contents
for RRC Connection Setup (Cell FACH) and RRC
Connection Release (Cell DCH) messages.
Correction to the default RRC message contents for the
IE UARFCN uplink (Nu)
Correction of references to IB UL:8 DL:8 kbps transport
channel parameters in reference radio bearer
configuration 6.10.2.4.1.58a
Correction of UE states tables for Generic setup
procedures.
Corrections to default message contents of
HANDOVER FROM UTRAN COMMAND-GSM
message.
Addition of multi-rate AMR-NB configuration with SRB#5
Proposed CR to 34.108 [R6 version, R99 affected] to
change slot format for AMR 5.9 mono rate RAB
Correction to puncturing limit in radio bearer
configuration 6.10.2.4.1.38a
Introduction of third RAB sublfow to WB-AMR test
configurations
Correction to RADIO BEARER SETUP message for
HSDPA RF testing
Correction to test procedure for HSDPA RF testing
2006-01: Editorial conversion to make file compatible
with Word 2000.
Corrections to GPS data files for signalling tests.
Corrections for reference RABs
Corrections to the RADIO BEARER SETUP message
for Enhanced uplink
Correction to default message content in INITIAL
DIRECT TRANSFER
Corrections to default message contents for signaling
Update of RB configuration 6.10.2.4.1.4b to increase
test coverage for multi-mode AMR configurations
Correction of UE RRC states table for common
procedures (section 7.4.1)
Correction to DPCCH power offset value in RADIO
BEARER SETUP messages
Introduction of Band VII and Band VIII to TS34.108
Chapter 5 and introduction of new UARFCN scheme
Clarification of RB Test Mode State for RF testing
Common message content for E-DCH RF testing
Generic test procedure for E-DCH RF testing
Correction to GPS Assistance Data for Performance
tests
Corrections to default message contents for RF
Adding of RB Configuration 6.11.4b to clause 6.11 to
increase test coverage for Interactive or background PS
RAB UL 0kbps/DL 0kbps.
Addition of release information to A-GPS
MEASUREMENT CONTROL message IEs
Change to altitude of simulated UE position
Clarification of A-GPS simulated satellites
Clarification to loopback on HSDPA call set up
procedure
Removal of alternative procedure for HSDPA RF testing
Removal of alternative RB Setup message for HSDPA
RF testing
CR for 34.108:Addition of RADIO BEARER SETUP
default message contents for LCR TDD HSDPA RF
testing
Correction to RB setup message for E-DCH
CR to 34.108: Addition of band IV to test frequencies for
UMTS 1.7/2.1 GHz
Addition of radio bearer setup and release for HCR
HSDPA testing to 34.108
HS-SCCH and HS-PDSCH power levels in signaling
3GPP
Doc-2ndLevel
6.0.0
6.1.0
R5-052144
6.0.0
6.1.0
R5-052145
D
F
6.0.0
6.0.0
6.1.0
6.1.0
R5-051840
R5-051848
6.0.0
6.1.0
R5-052155
6.0.0
6.1.0
R5-051858
6.0.0
6.1.0
R5-051942
6.0.0
6.1.0
R5-051955
F
F
6.0.0
6.0.0
6.1.0
6.1.0
R5-052176
R5-052055
6.0.0
6.1.0
R5-052096
6.0.0
6.1.0
R5-052140
6.0.0
6.1.0
6.0.0
6.1.0
6.1.0
6.1.1
F
F
F
6.1.1
6.1.1
6.1.1
6.2.0
6.2.0
6.2.0
R5-060522
R5-060273
R5-060335
6.1.0
6.2.0
R5-060396
F
F
6.1.1
6.1.1
6.2.0
6.2.0
R5-060274
R5-060122
6.1.1
6.2.0
R5-060268
6.1.1
6.2.0
R5-060459
6.1.1
6.2.0
R5-060440
F
F
F
F
6.1.1
6.1.1
6.1.1
6.1.1
6.2.0
6.2.0
6.2.0
6.2.0
R5-060446
R5-060439
R5-060438
R5-060007
F
F
6.1.1
6.1.1
6.2.0
6.2.0
R5-060257
R5-060571
6.2.0
6.3.0
R5-061454
F
F
F
6.2.0
6.2.0
6.2.0
6.3.0
6.3.0
6.3.0
R5-061410
R5-061223
R5-061046
F
F
6.2.0
6.2.0
6.3.0
6.3.0
R5-061212
R5-061213
6.2.0
6.3.0
R5-061438
F
F
6.2.0
6.2.0
6.3.0
6.3.0
R5-061443
R5-061188
6.2.0
6.3.0
R5-061148
6.2.0
6.3.0
R5-061207
Release 6
Meetin Doc-1st-Level
g-1stLevel
138
CR
Rev
Subject
tests
3GPP
Doc-2ndLevel
Release 6
139
Meetin Doc-1st-Level CR
g-1stLevel
RP-32 RP-060338
512
Rev
-
RP-32
RP-060338
513
RP-32
RP-060338
514
RP-32
RP-060332
515
RP-32
RP-060332
516
RP-32
RP-060332
517
RP-32
RP-060332
518
RP-32
RP-060332
519
RP-32
RP-060336
520
RP-32
RP-060322
521
RP-32
RP-060328
522
RP-32
RP-060322
523
RP-32
RP-060322
524
RP-32
RP-060322
525
RP-33
RP-33
RP-060560
RP-060549
526
527
RP-33
RP-33
RP-060549
RP-060549
528
529
RP-33
RP-060562
530
RP-33
RP-060568
531
RP-33
RP-060566
532
RP-33
RP-060567
533
RP-33
RP-060567
534
RP-33
RP-060562
535
RP-33
RP-33
RP-060562
RP-060562
536
537
RP-33
RP-060562
538
RP-33
RP-33
RP-060549
RP-060549
539
540
RP-33
RP-060549
541
RP-34
RP-060739
542
RP-34
RP-060731
543
RP-34
RP-34
RP-34
RP-060735
RP-060731
RP-060743
544
545
546
RP-34
RP-060731
547
RP-34
RP-060743
548
RP-34
RP-060743
549
RP-34
RP-060750
550
Subject
CR for 34.108:Addition of the combinations on DPCH
and HS-PDSCH for LCR TDD
CR for 34.108:Correction of RADIO BEARER SETUP
default message contents for LCR TDD HSDPA
CR for 34.108:Correction of RADIO BEARER RELEASE
default message contents for LCR TDD HSDPA
Corrections to the default RADIO BEARER SETUP
message for Enhanced uplink
Generalize E-DCH radio bearer names and correction to
section numbering for 6.10.2.4.6.3.2.1.1.2.
Addition of conversational radio bearer combinations for
E-DCH/HS-DSCH testing
E-HICH/E-RGCH and E-AGCH codes used in Radio
Bearer Setup for signaling
Introduction of additional WB-AMR RAB combination for
E-DCH/HS-DSCH testing
Addition of combinations on DPCH and HS-DSCH for
HCR to 34.108
Corrections to the values for IE based on calculated
ASN.1 value to 34.108 clause 9
CR to 34.108 Rel-6: Supplement to the UTRAN mobility
information procedure in TDD
Correction to specific message contents for UE
Capability Information confirm message
Corrections to the values for IE based on calculated
ASN.1 value to 34.108 clause 6
Addition of a new section for downlink physical channels
code allocation for signalling in FDD
Editorial changes in 34.108
CR to 34.108: Correction of reference test frequencies
for UMTS800 (Band VI)
Correction to SIB11 in 6.1
Correction to SECURITY MODE COMMAND message
in 9.2.1
Correction to RB Setup default message for E-DCH RF
testing
CR to 34.108: Correction the contents of RADIO
BEARER SETUP message: AM or UM (1.28 Mcps TDD)
Addition of HSDPA cases to radio bearer setup and
radio bearer release in section 9.1.2
Corrections to the default PHYSICAL CHANNEL
RECONFIGURATION message
Corrections to specification of HARQ RV sequence and
retransmissions for 34.123-1 test cases configuring
HSDPA
Corrections to the default RADIO BEARER SETUP
message
New Test RABS for MAC-E/Es test cases
Correction to radio bearer configuration 6.10.2.4.6 and
6.10.2.4.8
Correction to 34.108 Section 9.1 : Corrections to Radio
Bearer Setup for A12
Clarification to section 6.10 and 6.11
Correction to 34.108 Section 6.1 : Inclusion of System
Information Block Type 5bis
Corrections to maximum data rate for combinations on
PRACH (FDD)
Assistance Data change for A-GPS Minimum
Performance Test
Correction to SECURITY MODE COMMAND message
in 9.2.2
Addition of PAGING TYPE 2 message in 9.2
Correction to RADIO BEARER SETUP message in 9.2
Correction to the set of Reference E-TFCIs in RB Setup
default message (RF)
Correction the Default System Information Block type6
Messages in 6.1.0b
CR to 34.108, correction of RADIO BEARER SETUP for
EDCH
Correction to the set of Reference E-TFCIs in RB Setup
default message (SIG)
Introduction of radio bearers for MTCH
3GPP
Doc-2ndLevel
6.2.0
6.3.0
R5-061310
6.2.0
6.3.0
R5-061053
6.2.0
6.3.0
R5-061054
6.2.0
6.3.0
R5-061314
6.2.0
6.3.0
R5-061315
6.2.0
6.3.0
R5-061266
6.2.0
6.3.0
R5-061386
6.2.0
6.3.0
R5-061339
6.2.0
6.3.0
R5-061149
6.2.0
6.3.0
R5-061369
6.2.0
6.3.0
R5-061392
6.2.0
6.3.0
R5-061139
6.2.0
6.3.0
R5-061281
6.2.0
6.3.0
R5-061385
F
F
6.3.0
6.3.0
6.4.0
6.4.0
R5-062092
R5-062440
F
F
6.3.0
6.3.0
6.4.0
6.4.0
R5-062427
R5-062403
6.3.0
6.4.0
R5-062208
6.3.0
6.4.0
R5-062511
6.3.0
6.4.0
R5-062253
6.3.0
6.4.0
R5-062291
6.3.0
6.4.0
R5-062544
6.3.0
6.4.0
R5-062320
F
F
6.3.0
6.3.0
6.4.0
6.4.0
R5-062328
R5-062199
6.3.0
6.4.0
R5-062348
F
F
6.3.0
6.3.0
6.4.0
6.4.0
R5-062194
R5-062398
6.3.0
6.4.0
R5-062350
6.4.0
6.5.0
R5-063400
6.4.0
6.5.0
R5-063296
F
F
F
6.4.0
6.4.0
6.4.0
6.5.0
6.5.0
6.5.0
R5-063401
R5-063402
R5-063233
6.4.0
6.5.0
R5-063294
6.4.0
6.5.0
R5-063545
6.4.0
6.5.0
R5-063240
6.4.0
6.5.0
R5-063543
Release 6
140
Meetin Doc-1st-Level CR
g-1stLevel
RP-34 RP-060749
551
RP-34 RP-060735
552
Rev
-
RP-34
RP-34
RP-060731
RP-060731
553
554
RP-34
RP-060731
555
RP-34
RP-060731
556
Subject
Introduction of FDD interband testing in TS 34.108
Correction to Radio Bearer Setup message Mac-hs
reset indicator
CR to 34.108, Add MCC value for Band VI test
CR to 34.108, Modify MCC value in IMSI of test USIM
for Band VI test
Correction to default content for System Information
Block Type 7
Clarification of FDD test channels used for signaling test
cases
3GPP
Doc-2ndLevel
F
F
6.4.0
6.4.0
6.5.0
6.5.0
R5-063255
R5-063339
F
F
6.4.0
6.4.0
6.5.0
6.5.0
R5-063340
R5-063341
6.4.0
6.5.0
R5-063079
6.4.0
6.5.0
R5-063260