Professional Documents
Culture Documents
Features
Ordering Information
To specify options, choose from the list below.
Note: RoHS compliant units are identified by the letter G appearing immediately at the end of ordering code.
Model
(non RoHS compliant)
Main Unit
Loop-V4200-9
Model
(RoHS compliant)
Loop-V4200-9-G
Loop-V4200-V35-G
Loop-V4200-E530-G
Loop-V4200-RS232-G
Loop-V4200-X21-G
Loop-V4200-QFXS-x-pt -G
Loop-V4200-QFXS-M-x-pt Loop-V4200-QFXS-M-x-pt G
Loop-V4200-QFXS-M12-x- Loop-V4200-QFXS-M12-x-pt
pt
-G
Loop-V4200-QFXS-GS-x- Loop-V4200-QFXS-GS-x-pt pt
G
Loop-V4200-QFXS-GM-x- Loop-V4200-QFXS-GM-x-pt
pt
-G
Loop-V4200-QFXO-x
Description
Main unit w/ CPU and DCS,
w/o power
T1 interface card
E1 interface card with 75 ohm
E1 interface card with 120
ohm
V.35/DB25 interface card
EIA530 interface card
RS232 interface card
X.21 interface card
Quad FXS voice card using 4
RJ11
Quad FXS with MP 16KHz
voice card using 4 RJ11
Quad FXS with MP 12KHz
voice card using 4 RJ11
Quad FXS with GS using 4
RJ11
Quad FXS with GS and MP
16KHz voice card using 4
RJ11
Note
Basic Chassis
GS = Ground Start
MP = Metering Pulse TX
12K/16KHz
pt = power type
For pt option, please refer
to the table below for detail
information
QFXS-GM includes all QFXS
card functions
Loop-V4200-QFXO-x-G
Loop-V4200-Q4EM-m-Tnx
Loop-V4200-Q4EM-m-Tn-xG
Loop-V4200-PLAR
Not available
Loop-V4200-PLM(A)
Not available
Loop-V4200-PLM(B)
Not available
Loop-V4200-GH
Loop-V4200-GH-G
Loop-V4200-AFRT
Loop-V4200-AFRT-G
Loop-V4200-AFRE
Loop-V4200-AFRE-G
Loop-V4200-RT
Loop-V4200-RT-G
Loop-V4200-CD
Loop-V4200-TS
Loop-V4200-CD-G
Loop-V4200-TS-G
GS = Ground Start
MP = Metering Pulse RX
12K/ 16KHz
QFXO-GM includes all QFXS
card functions
Loop-V4200-SNMP
Loop-V4200-FOM-opt
Loop-V4200-SNMP-G
Loop-V4200-FOM-opt-G
Loop-V4200-SD24
Loop-V4200-SD48
Loop-V4200-DD24
Not Available
Loop-V4200-SD48-G
Not Available
Loop-V4200-DD48
Loop-V4200-DD48-G
SNMP module
Fiber Optical Interface
ACC-CAB-DB44M-1002DB25F-1DB09F-TS)
Optional
Accessories
Tapping Bridge Box
Loop-ACC-TB
Not available
Cables (All cables are RoHS compliant)
Loop-ACC-CAB-DB44M- DSUB-44 pin/Male to two DSUB-25 pin/Female- one DSUB- For Loop-V4200-TS plug-in
100- 2DB25F-1DB09F-TS 9 pin/Female (8P8C) plug, Length:100cm
card
Power Cord (All power cords are RoHS compliant)
Loop-ACC-PC-USA
AC power cord for
Taiwan/USA
Loop-ACC-PC-EU
AC power cord for Europe
Loop-ACC-PC-UK
AC power cord for the UK
Loop-ACC-PC-AUS
AC power cord for Australia
Loop-ACC-PC-CH
AC power cord for China
Blank Panels
30.000112.A00
30.000112.A00-G
Dummy Panel for V4200-9
Users Manual
Loop-V4200-9-UM
Users Manual (paper copy).
Note: A CD version of the manual is already included as standard package.
Ear Mounts
19/23 ear mounts
A pair of 19/23 ear mounts is supplied as part of standard package
.
Note: For other sizes, please contact your nearest Loop sales representative.
Where m is used to select QEM card signaling side (must select one):
m=
Description
B
B (carrier side) connects to A side.
A
A (exchange side) connects to B side. A side M lead to B side M lead, A
side E lead to B side E lead.
Where n is used to select QEM card signaling type (must select one):
n=
Description
O
For voice transmission only.
1
Type I (Original) E&M Signaling Circuit
2
3
4
5
Type II Circuit. This design attempts to reduce ground noise by adding two
leads: SB (Signal to Battery) and SG (Signal to Ground)
Type III Circuit. The SG lead serves as a discharge for the M lead.
Reduces delay caused by combination of (a) low current electronic
detectors, and (b) long runs of the E and M leads.
Type IV Circuit. Based on the Type 2 circuit. This E&M circuit provides
symmetry.
Type V Circuit. For applications where ground noise is not an issue.
Based on the Type 2 circuit.
Note
Note
Circuit Type doesnt matter.
M lead provides discharge for
the A side.
Reduced ground noise.
Ground current is eliminated at
the cost of two more wires per
circuit.
Type III is rare because ground
currents on the E return would
cause noise
Note
Note
Use 2 fibers
Units delivered
ITU-T Rec G.957 application
code
Note
For QFXS, QFXO, Q2EM, and Q4EM
Firmware Upgrade
Loop-V4200-9- Firmware Upgrade and Warranty Renewal.
For available card types,
FWUPGR
The Customer whose warranty has lapsed or desire to have a
please refer to the table below
firmware upgrade can purchase this option.
for detail information.
Loop-V4200This will upgrade the firmware to the most current version and provide
card-FWUPGR an additional 12 months of support.
For Firmware Upgrade:
Where card is used to select card type:
card=
Description
RT
2-port RT card
TS
Terminal Server Interface card
Note
For example:
Loop-V4200-9
1 each Loop-V4200-SA
1 each Loop-V4200-E75
5 each
Loop-V4200-T1
4 each Loop-ACC-PC-UK
1 each
For model 4200 with 4 T1 cards, 5 E75 cards, and a single AC power with the AC power cord for the UK.
ESC
M UXM ASTER
ACO
POWER TEST
9600, n.8.1
IN OU T MON
E NT E R
C ON S OLE
Keypads
LCD
LED
Bantam Jacks
Rear Panel
5 keys, ACO (alarm cut-off), left and right arrows, ESC, and ENTER
2 lines by 40 characters LCD display
12 - one for each of 9 plug-in slots, power, test, and alarm
Network IN, OUT, and Monitor
QFXO
DC 48 V
QFXS
QFXS
M DSL
T1
DTE-X.2 1
RS2 3 2
E1
E1
DC 48 V
ALARM
ETHERNET
CISPR 22 Class A, EN55022 Class A, EN50024, FCC Part 15, FCC Part 68, CS-03 Issue 8, CE168X, NTR4,
UL1950, CSA22.2 No.950, EN60950, NEBS Level 3: GR-1089-CORE, GR-63-CORE
Application Illustration
E1
V.35
QFXS
E1
V.35
QFXS
E1
Loop-V4200
As an E1 CSU/DSU w/voice
Loop-V4200
E1
T1
As a T1 CSU/DSU w/voice
E1
Loop-V4200
E1
T1
Loop-V4200
E1
E1
T1
T1
Loop-V4200
Loop-V4200
As an 9E1 TSI
As an 9T1 TSI
1
QFXS
1
QFXS
T1
Loop-V4200
Monitor Channel
E1
Loop-V4200
V.35
T1
Loop-V4200
E1
V.35
Loop-V4200
QFXS 15
T1
V.35
Loop-V4200
QFXS 12
As an E1 MuxMaster
LoopTelecom.com
T1
Monitor Channel
V.35
Loop-V4200
E1
Loop-V4200
T1
As a T1 MuxMaster
Worldwide
Taipei, Taiwan
North America
Tianjin, China
8 Carrick Road
Palm Beach Gardens
Florida 33418, U.S.A.
+1-561-627-7947
jimber561@aol.com