Professional Documents
Culture Documents
G - 40 REV
Phone: 615-350-7975
Fax: 615-350-6067
CC:
Date:
Ref:
X
13-Jul-15
New Submittal
Resubmittal
We Are Sending:
x
Shop Drawings
Letter
Prints
Change Order
Plans
X
Samples: Provided on 7/16/15
Specifications
Other:
Submittal Type:
Submitted For:
X
Approval
Your Use
As Requested
Review and Comment
Sent Via:
X
Action Taken:
Approved as Submitted
Approved as Noted
Returned After Loan
Resubmit
Submit
Returned
Returned for Corrections
Due Date:
27-Jul-15
Attached
Separate Cover Via:
Shop Drawing
Quality Control
Administrative
Contract Closeout
Sample
"Or Equal"/Substitute
Description
Spec.
Section
Qty
6.74.14
DIG
Submittal No.
G-
40 REV
Contractor's Stamp
Notes:
Engineer's Stamp/Comments
Jordan Carrier
Contains Variation
to Specifications
Yes
No
13-Jul-15
Date
A. FURNISH AS SUBMITTED
B. FURNISH AS NOTED
C. REVISE AND RESUBMIT
D. REJECTED
E. ENGINEER'S REVIEW NOT REQUIRED
The Engineers review is only for conformance with the design
concept of the Project and compliance with the information given
in the Contract Documents. Any and all markings noted by the
Engineer shall not relieve the Contractor from compliance with
the Contract Documents, nor allow departures therefrom. The
Contractor is responsible for details and accuracy; for the
quantities and dimensions to be confirmed and/or correlated; for
information that pertains solely to the fabrication processes or to
techniques of construction; for coordination of the work of all
trades; and for performing work in a safe manner.
G-40B_REV2
REVIEWER:
Michael T. Rudisell, PE
DESCRIPTION:
FRP Grating, Framing, and Handrail for CSO Control Structures (Revision 2)
SUBMITTAL TYPE:
SHOP DRAWING
DATE:
8/7/2015
SAMPLE
INFORMATION
D. REJECTED
NO.
COMMENT
FRP Grating, Framing, and Handrail for CSO Control Structures (Revision 2)
1. For CSO097, the gate is shown on the wrong side of the Structure. The 24"
gate should be located on the 5'-0" side (not 7'-0" side). Revise platform
configuration. See Sheet C-38 and reference gate shop drawings. Also, the
top of grating shall be installed 4'-0" below the bottom of the concrete top
slab. There should be approx. 4-foot clear height. This applies to CSO097
only. Resubmit this revised drawing under separate cover for
review/approval.
2. Contractor shall coordinate FRP framing, grating, and railing with gate
frames, actuators, conduits, MH steps, etc. to avoid interferences. Reference
gate shop drawings to ensure the width of the electric actuators has adequate
clearance in all structures. All platforms shall be installed 7-0 below the
bottom of the top slab to provide 7-foot clear height (except CSO097).
DISPOSITION
REV 05/10
Form 299SR
Subject:
Project:
Dear Michael,
Following is the response to the comments you made on Heumann Environmental Companys
submittal package revision A:
1. See red markups on submittal for additional comments to be addressed in the resubmittal. Provide additional items for record..
RESPONSE: All markups have been addressed on this re-submittal packet.
2. Define the resin to be used for the framing and handrail, VEFR-20 or VEFR-10?
RESPONSE: Resin has been defined since resubmittal packet Rev B; and it defined again
as VEFR-20
3. Similar to original submittal, provide the manufacturers published literature
including: product data sheets, structural design data, structural properties data,
grating load/deflection tables, corrosion resistance tables, ISO certificates of
compliance, test reports, and design calculations for grates and support systems.
RESPONSE: All above mentioned items have been included on this re-submittal packet.
See Annex# 1 for chemical resistance tables.
4. Provide load tables/calculations for the grating based on the size and type being
furnished for the project. Deflection shall not exceed 1/8 at a pedestrian loading of
300psf. Verify.
RESPONSE: Confirmed. See grating verification and load tables for grating.
5. Manufacturer shall provide proof of certification from ISO and at least two other
quality assurance programs for its facilities or products (UL, DNV, ABS, USCG,
and AARR). Confirm.
RESPONSE: Complied. See Annexes 2, 3 and 4 for quality assurance program
certificates.
6. Manufacturer shall provide documentation for the three (3) year limited warranty
on all FRP products against defects in materials and workmanship.
RESPONSE: See Annex 5 for Warranty certificate.
7. Coordinate FRP framing, grating, and railing with gate frames, actuators, conduits,
MH steps, etc. to avoid interferences.
RESPONSE: Contractor to coordinate and markup any additional required penetrations
on grating or changes in handrail layout prior to release for fabrication.
8. Provide a detail for the hinges 30x30 access grating section.
RESPONSE: Hinge locations, details, and attachment method have been added to
approval drawings.
9. For CSO148, the gate is shown on the wrong side of the Structure. See Sheet C-33.
Revise platform configuration.
RESPONSE: Grating, handrail, and supports layout have been revised to show the gate
on the west side of the structure.
10. Due to headroom/clearance issues, no platform is required for CSO097.
RESPONSE: Platform for CSO-097 has been deleted from the project.
Drawing for CSO-097 included per the request of MSD in the progress meeting on 7/16/15
11. Per RFI#16, the Contractor requested that this structure be enlarged. However,
after the Engineer's review, it was recommended for this structure to remain as 6foot diameter. Therefore, these platforms dimensions should be acceptable.
Contractor shall confirm.
RESPONSE: Acknowledged, no action taken.
To be re-submitted
under separate cover
Feel free to get in touch if you have any further questions or comments.
Best Regards,
Emelkin Lozano
Project Manager
Delta Composites, LLC
TEL: 281-907-0619
FAX: 281-907-0323
Email: elozano@deltacomposites.com
CALCULATIONS
PACKAGE
FRP GRATING, HANDRAIL SYSTEM
AND SUPPORTS
Heumann Environmental Company, LLC (BADD)
Logan CSO Interceptor Platforms
Louisville, MO
DELTA PROJECT# 17134
TO BE SUBMITTED WITH
APPROVAL DRAWINGS REV D
FRP GRATING
PRODUCT DATA & LOAD/
DEFLECTION VERIFICATION
DeltaGrate HS
High Strength Molded Grating
Higher Stiffness
DeltaGrateTM HS Molded Grating is manufactured using a
proprietary method enabling a higher percentage of glass
rovings to be introduced into the grating. Conventional
open-top molded gratings are constructed with approximately
25-30% glass content by weight, whereas DeltaGrateTM HS
contains 38% glass content. The corrosion resistance of
fiberglass grating is provided by the resin, and the stiffness is
provided by the glass. Possessing a higher glass content
results in a stiffer fiberglass grating. As a result, DeltaGrateTM
HS is 15-20% stiffer than the gratings produced by other
manufacturers of open-top molded fiberglass gratings
without compromising any of the other inherent qualities of
molded fiberglass grating. In an independent study
conducted by the University of Mississippi on several
prominent manufacturers of open top molded gratings,
DeltaGrateTM HS placed FIRST in overall stiffness.
Chemical Resistance
With approximately 62% resin content, DeltaGrateTM HS
Molded Grating offers superb chemical resistance to a variety
of acids and caustics. DeltaGrateTM HS is offered in an array
of corrosion resistant resins designed for any environment,
from light or moderately corrosive environments to extremely
corrosive applications.
Lightweight
DeltaGrateTM HS 1 molded grating weighs 2.5 psf compared
to 7.5 psf for 1 steel grating. DeltaGrateTM HS 1 1/2
molded grating weighs 3.75 psf compared to 11.5 psf for
1 1/2 steel grating. DeltaGrateTM HS weighs 1/3 the weight
of steel gratings resulting in easier installations and lower
installation costs.
Impact Resistance
DeltaGrateTM HS Molded Gratings provide excellent impact
resistance and are tested in accordance with ASTM 695-79
(1985) as established by the Fiberglass Grating
Manufacturers Council (U.S.A.).
Fire Retardancy
product.
Ultra-violet resistant
Textile
Electrical & Power
Generation
Computer and Hi-tech
Metal Plating
Food & Beverage
Shipping
Many others
Grating Selection
Delta Composites offers both molded and pultruded gratings. The following table provides assistance in selecting the best
grating for the application.
Pultruded Grating
Chemical Resistance
Excellent
Good
Bi-directional Strength
Excellent
Not Recommended
Unidirectional Strength
Very Good
Excellent
Impact Resistance
Excellent
Average
Excellent
Excellent
Excellent
Excellent
Pipe Penetrations
Excellent
Average
Safety
Excellent
Excellent
For any applications requiring our pultruded fiberglass gratings, please see the DeltaSpan Pultruded Fiberglass Grating
brochure for additional information.
Mesh
Description
Bars/ft
Panel Sizes
Available
Weight
(psf)
% Open
Area
1/2
4 x 8
4 x 12
0.8
87%
1/2
1/2 x 1 x 4 Rectangular
(DeltaLiteTM)
12
3 x 10
4 x 8
1.2
68%
1/2
2 x 2 Square (DeltaLiteTM)
4 x 12
1.08
71%
1 x 4 Rectangular
12
3 x 10
2.6
68%
3 x 10, 4 x 8
4 x 12
2.5
68%
1-1/4
16
3.3 x 9.8
(1m x 3m)
3.86
42%
1-1/4
(30mm)
4m x 1m
3m x 1m
2m x 1m
3.2
68%
1 1/2
3 x 10 x 4 x 8
4 x 12, 5 x 10
3.8
68%
1 1/2
1 x 6 Rectangular
(DeltaTreadTM)
12
22 1/4 x 10
4.85
56%*
2 x 2 Square
4 x 12
4.5
71%
Resin Selection
Delta Composites manufactures molded grating in a variety
components: the resin type and its ASTM E-84 flame spread
the CFR-25 gratings are yellow and dark gray. Type CFR-10,
rating.
where fire resistance, low smoke, and low toxic fumes are
orange, and the standard color for the VEFR-10 is dark gray.
Conductive Top Grating: All of Delta Composites
Type IFR-25 is a premium isophthalic polyester resin with a
10. The standard color for the IFR-25 is green and the IFR-
engineering@deltacomposites.com.
TM
teamwork.
Reduction in costs associated with failures and/or
production errors.
Systematic resolution of specification non-conformance
and the incorporation of preventive measures and
corrective action.
Improved communications, both internally and
externally, resulting in improved quality, efficiency,
on-time delivery, and customer/supplier relations.
Worldwide recognition of compliance by an unbiased
and respected organization.
Installation Accessories
INSTALLATION whenever possible, provide for a minimum of 1-1/2 of bearing support at all grating support points.
Holddown clips should be used at the rate of one clip for every 6 ft2 of grating minimum, or at least 4 clips for any square or
rectangular piece, or at least 3 for a triangular piece.
Type M
Type C
Type GW
Type S
HiltiTM Fastener
CHEMICAL
ENVIRONMENT
Acetic Acid
Aluminum Hydroxide
Ammonium Chloride
Ammonium Hydroxide
Ammonium Bicarbonate
Ammonium Sulfate
Benzene
Benzoic Acid
Borax
Calaum Carbonate
Calcium Nitrate
Carbon Tetrachloride
Chlorine, Dry Gas
Chlorine Water SAT
Chromic Acid
Citric Acid
Copper Chloride
Copper Cyanide
Copper Nitrate
Ethanol
Ethylene Glycol 100
Ferric Cholride
Ferrous Chloride
Formaldehyde
Gasoline
Glucose
Glycerine
Hydrobromic Acid
Hydrochloric Acid
Hydrogen Peroxide
Lactic Acid
Lithium Chloride
Magnesium Chloride
Magnesium Nitrate
Magnesium Sulfate
Mercuric Chloride
Mercurous Chloride
Nickel Chloride ALL
Nickel Sulfate
Nitric Acid
Oxalic Acid
Perchloric Acid 30
Phosphoric Acid
Potassium Chloride
Potassium Dichromate
Potassum Nitrate
Potassium Sulfate
Propylene Glycol
Sodium Acetate
Sodium Bisulfate
Sodium Bromide
Sodium Cyanide
Sodium Hydroxide
Sodium Nitrate ALL
Sodium Sulfate ALL
Stannic Chloride
Sulfuric Acid
Tartaric Acid
Vinegar
Water, Distilled 100
Zinc Nitrate
Zinc Sulfate
TYPE VEFR-20
% CONCENTRATION
50
100
All
28
50
ALL
N/R
SAT
SAT
ALL
ALL
100
200/93
10
ALL
ALL
ALL
ALL
50
200/93
ALL
ALL
ALL
100
100
100
50
37
30
ALL
SAT
ALL
ALL
ALL
100
ALL
210/99
ALL
20
ALL
100/38
100
ALL
ALL
ALL
ALL
ALL
ALL
ALL
ALL
ALL
25
210/99
210/99
ALL
75
ALL
100
180/82
ALL
ALL
180/82
180/82
210/99
100/38
160/70
210/99
N/R
210/99
210/99
180/82
210/99
150/65
210/99
SAT
150/65
210/99
210/99
210/99
210/99
100/38
100
210/99
210/99
150/65
180/82
210/99
210/99
150/65
150/65
150/65
210/99
210/99
210/99
210/99
210/99
210/99
210/99
ALL
210/99
120/49
210/99
N/R
210/99
210/99
210/99
210/99
210/99
210/99
210/99
210/99
210/99
210/99
180/82
ALL
ALL
210/99
100/38
210/99
210/99
100
210/99
210/99
TYPE IFR-25
% CONCENTRATION
50
100
All
28
15
ALL
N/R
SAT
SAT
ALL
ALL
N/R
80/27
5
ALL
ALL
ALL
ALL
50
90/32
ALL
ALL
50
100
100
100
50
37
5
ALL
SAT
ALL
ALL
ALL
100
ALL
170/77
ALL
20
ALL
N/R
100
ALL
ALL
ALL
ALL
ALL
ALL
ALL
ALL
ALL
N/R
170/77
170/77
ALL
25
ALL
100
170/77
ALL
ALL
125/52
160/71
170/77
N/R
125/52
170/77
N/R
150/66
170/77
170/77
180/82
N/R
140/60
70/21
170/77
170/77
170/77
170/77
75/24
170/77
170/77
75/24
80/27
170/77
150/66
120/49
75/24
100/38
170/77
150/66
170/77
140/60
170/77
150/66
140/60
170/77
70/21
75/24
120/49
170/77
170/77
170/77
170/77
170/77
160/71
170/77
170/77
170/77
N/R
160/71
75/24
170/77
170/77
170/77
170/77
TM
TM
each can.
Product Data
1"
.33"
2"
Bearing Bar
Weight
height
width
open
area
bar/ft
space
center
lb/ft
1.5"
0.43"
0.25"
12
0.57"
1"
6.2
0.43"
1"
1.5"
Span
Inches
100
200
300
400
500
600
700
800
900
1000
Max. Recom.
(psf)
12
<0.01
<0.01
<0.01
<0.01
<0.01
<0.01
<0.01
<0.01
<0.01
<0.01
28000
18
<0.01
<0.01
0.01
0.01
0.02
0.02
0.02
0.03
0.03
0.03
12400
24
0.01
0.02
0.03
0.04
0.05
0.06
0.08
0.09
0.10
0.11
6500
30
0.03
0.05
0.08
0.11
0.13
0.16
0.18
0.21
0.24
0.27
4000
36
0.05
0.10
0.16
0.21
0.27
0.31
0.4
0.42
0.47
3000
42
0.10
0.20
0.29
0.40
0.48
2000
Span
Inches
100
200
300
500
1000
2000
3000
4000
5000
6000
Max. Recom.
(lb/ft)
12
<0.01
<0.01
<0.01
<0.01
0.01
0.03
0.04
0.06
0.07
0.08
14000
18
<0.01
<0.01
0.01
0.02
0.04
0.07
0.11
0.15
0.18
0.22
9000
24
<0.01
0.02
0.03
0.04
0.09
0.17
0.26
0.34
0.43
6500
30
0.02
0.03
0.05
0.08
0.17
0.35
5400
36
0.03
0.06
0.09
0.15
0.30
4500
42
0.04
0.100
0.13
0.23
0.45
3500
Grating available in (6 wide x 4 span) and (12 wide x 4 span) stock size panels only.
TYPE
WHEEL
LOAD (lbs)
MAXIMUM
ALLOWABLE
SPANS
AASHTO
H-20
Automobile
5-Ton
Forklift
3-Ton
Forklift
1-Ton
Forklift
32,000 lb
Axle Load
with dual
wheels
Up to a
5,000 lb
Vehicle
24,000 lb
total
(loaded)
15,500 lb
total
(loaded)
6,200 lb
total
(loaded)
20,800
2,200
13,400
8,700
3,400
1' - 2"
2' - 2"
1' - 0"
1' - 0"
1' - 7"
END OF SECTION
ASTM
Test
Units
1500/1525
Series
1625
Series
D790
D790
D790
D2344
D732
D256
D256
D953
D953
D3039
D3039
D23444
D23444
psi
106 psi
106 psi
psi
psi
ft lbs/in
ft lbs/in
psi
psi
in/in
in/in
psi
psi
17,360
1.9
1.75
3,400
5,500
38
19
33,980
30,0003
0.35
0.12
7,000
4,500
19,900
1.9
1.75
3,900
6,000
43
22
39,000
34,500
0.35
0.12
7,000
4,500
33
0.6
0.060-0.070
1.66-1.93
4.4
39
0.6
0.060-0.070
1.66-1.93
4.4
120
40
200
5.2
120
40
200
5.2
D2583
D570
D792
D792
D696
% Max
lbs/in3
C177
10-6in/in/F
BTUin/ft2/hr/F
Electrical
Arc Resistance (LW)
Dielectric Strength (LW
Dielectric Strength (PF)
Dielectric Constant (PF)
D495
D149
D149
D150
seconds
KV/in
Volts/mil
@60Hz
LW = Lengthwise
CW = Crosswise
Pultex uses a synthetic surface veil that reduces the Barcol hardness, but does not reflect lack of cure.
Full section testing based on a 3-point bend with simply supported end conditions.
3
Crosswise bearing stress of Web sections of profiles = 20,500 psi
4
Follow ASTM D2344, but rotate coupon 90 deg. (cut section of coupon length faces up)
2
Property
ASTM
Test
1500/1525
Series
1625
Series
Flammability Classification
Tunnel Test
UL94
ASTM E84
Flammability Extinguishing
NBS Smoke Chamber
ASTM D635
ASTM E662
FTMS
406-2023
(VO)
25 Max
Self
Extinguishing
650
55/30
(seconds)
(VO)
25 Max
Self
Extinguishing
650
55/30
(seconds)
20
modified
modified
ASTM
Test
Units
1500/1525
Series
1625
Series
D638
D638
D638
D638
D695
D695
D695
D695
D790
D790
D790
D790
Full Section 2
Full Section 2
D2344
D732
D256
D256
D953
D953
D3039
D3039
D2344
D2344
psi
psi
106 psi
106 psi
psi
psi
106 psi
106 psi
psi
psi
106 psi
106 psi
106 psi
106 psi
psi
psi
ft lbs/in
ft lbs/in
psi
psi
in/in
in/in
psi
psi
31,000
16,500
3.5
1.0
33,800
25,500
3.0
2.2
43,500
24,000
1.9
1.6
2.8
0.5
3,400
5,500
34
33
33,000
33,000
0.35
0.12
4,500
7,000
35,600
18,900
3.5
1.0
44,500
29,000
3.0
2.2
50,000
27,500
1.9
1.6
2.8
0.5
3,900
6,000
39
38
38,000
38,000
0.35
0.12
4,500
7,000
21
ASTM
Test
Physical
Barcol Hardness 1
Water Absorption
Density
Specific Gravity
Coefficient of Thermal Expansion (LW)
D2583
D570
D792
D792
D696
C177
10-6in/in/F
BTUin/ft2/hr/F
Electrical
Arc Resistance (LW)
Dielectric Strength (LW
Dielectric Strength (PF)
Dielectric Constant (PF)
D495
D149
D149
D150
seconds
KV/in
Volts/mil
@60Hz
LW = Lengthwise
CW = Crosswise
Units
% Max
lbs/in3
1500/1525
Series
1625
Series
45
0.6
0.060-0.070
1.66-1.93
4.4
45
0.6
0.060-0.070
1.66-1.93
4.4
120
40
200
5.2
120
40
200
5.2
Pultex uses a synthetic surface veil that reduces the Barcol hardness, but does not reflect lack of cure.
Full section testing based on a 3-point bend with simply supported end conditions.
3
Follow ASTM D2344, but rotate coupon 90 deg. (cut section of coupon length faces up)
2
Property
ASTM
Test
1500/1525
Series
1625
Series
Flammability Classification
Tunnel Test
UL94
ASTM E84
Flammability Extinguishing
NBS Smoke Chamber
ASTM D635
ASTM E662
FTMS
406-2023
(VO)
25 Max
Self
Extinguishing
650
55/30
(seconds)
(VO)
25 Max
Self
Extinguishing
650
55/30
(seconds)
22
=
=
=
=
Vinyl Ester
100
0.00
lbs
300.00
psf
10.00%
0.00%
Beam Properties
10
bw = Web Depth =
in.
10.00
psf
bf = Flange Width =
in.
psf
tf = Flange Thickness =
0.375
in.
Safety Factor =
310.00
2.5
tw = Web Thickness =
0.375
in
Length of Beam ( L ) =
4.50
ft
54.00
in
Tributary width =
2.13
ft
25.56
in
1380.24
in2
Area =
Weight =
6.57
in
4.92
lb/ft
Sx =
13.59
in
Ix =
40.76
r =
2.49
Sy =
Iy =
r
Full Section EX
EC-LW (Web)
EC-LW (Flange)
EC-CW (Web)
EC-CW (Flange)
Gxy
L
J
CW
=
=
=
=
=
=
=
=
=
=
ft
Unbraced Length ( Lu ) =
9.59
54.00
in4
Max Deflection =
0.13
in
in
NA
in
Warning Box
4.44
in
13.32
1.42
4.000E+06
2.800E+06
3.850E+06
1.900E+06
1.900E+06
5.E+05
54.00
0.316
119.88
Area Of Load =
S.F.
Applied Moment =
in
in
psi
psi
psi
psi
psi
psi
in
AW
k
A'
w
w
Fb
Fb1
fb
vxy
vyx
=
=
=
=
=
=
=
=
=
=
=
in4
6
in
Compressive Strength, Fc-flg-LW
Ultimate Beam Shear Strength, Fv-ult =
0.00
2.2500
1.0000
2.2500
660.30
55.03
33000
13200
1475.84
0.35
0.12
52500
7000
lbs-in
2
in
in2
lbs/ft
lbs/in
psi Full Section Flexural Strength
psi
psi
psi
psi
=
=
=
=
=
Maximum Acting Shear Load =
Point Load M MAX
Unifrom Load M MAX
Applied M MAX
Total M MAX
Total Load
0.00
20056.61
0.00
20056.61
2971.35
1485.68
lbs-in
lbs-in
lbs-in
lbs-in
lbs
lbs
Deflection =
0.0552
in
L / 978.36
Note: The calculation for delfection is only for a Point Load and a
Uniform Load. The deflection for the Applied Moment is not
included.
3.00
2333.33
2100.00
4725.00
lbs
22340.61
psi
psi
O.K.
LOCAL BUCKLING
Critical Local
Buckling Stress scr =
b
z
p
q
=
=
=
=
If the calculated Local Buckling Stress above exceeds the Flange Compression Strength of the material, use cr
Therefore, cr
local
22340.61
20106.55
psi
Fb Local Buckling =
8042.62
psi
fb =
1475.84
psi
D =
JG =
Iww =
175028027.34
158203.13
469214648.44
local
O.K.
GLOBAL BUCKLING
global
102943.54
lbs
global
102261.79
psi
33000
psi
Therefore, cr
global
global
29700.00
psi
global
11880.00
psi
fb =
1475.84
psi
Fb
D Calcs.
155925000
18900000
203027.34
psi in
psi in4
psi in6
Pcrglobal Calcs.
0.0058882
5262127
3.3224235
O.K.
JG Calcs.
105468.75
52734.375
Iww Calcs.
467775000.00
1218164.063
221484.375
=
=
=
=
Vinyl Ester
100
0.00
lbs
300.00
psf
10.00%
0.00%
Beam Properties
10
bw = Web Depth =
in.
10.00
psf
bf = Flange Width =
in.
psf
tf = Flange Thickness =
0.375
in.
Safety Factor =
310.00
2.5
tw = Web Thickness =
0.375
in
Length of Beam ( L ) =
6.00
ft
72.00
in
Tributary width =
2.25
ft
27.00
in
1944.00
in2
Area =
Weight =
6.57
in
4.92
lb/ft
Sx =
13.59
in
Unbraced Length ( Lu ) =
Ix =
40.76
in4
r =
2.49
in
Sy =
Iy =
r =
Full Section EX =
EC-LW (Web) =
EC-LW (Flange) =
EC-CW (Web) =
EC-CW (Flange) =
Gxy =
L =
J =
CW =
13.50
30.00
ft
Max Deflection =
0.13
in
240.00
Applied Moment =
0.00
2.2500
1.0000
2.2500
697.50
58.13
33000
13200
2771.52
0.35
0.12
52500
in
Warning Box
4.44
in
13.32
1.42
4.000E+06
2.800E+06
3.850E+06
1.900E+06
1.900E+06
5.E+05
72.00
0.316
119.88
Area Of Load =
S.F.
in
in
psi
psi
psi
psi
psi
psi
in
AW
k
A'
w
w
Fb
Fb1
fb
vxy
vyx
=
=
=
=
=
=
=
=
=
=
=
in4
6
in
Compressive Strength, Fc-flg-LW
Ultimate Beam Shear Strength, Fv-ult =
7000
lbs-in
2
in
in2
lbs/ft
DEFLECTION IS OVER THE MAX
lbs/in
psi Full Section Flexural Strength
psi
psi
psi
psi
=
=
=
=
=
Maximum Acting Shear Load =
Point Load M MAX
Unifrom Load M MAX
Applied M MAX
Total M MAX
Total Load
0.00
37665.00
0.00
37665.00
4185.00
2092.50
lbs-in
lbs-in
lbs-in
lbs-in
lbs
lbs
Deflection =
0.1582
in
L / 455.04
Note: The calculation for delfection is only for a Point Load and a
Uniform Load. The deflection for the Applied Moment is not
included.
3.00
2333.33
2100.00
4725.00
lbs
22340.61
psi
psi
O.K.
LOCAL BUCKLING
Critical Local
Buckling Stress scr =
b
z
p
q
=
=
=
=
If the calculated Local Buckling Stress above exceeds the Flange Compression Strength of the material, use cr
Therefore, cr
local
22340.61
20106.55
psi
Fb Local Buckling =
8042.62
psi
fb =
2771.52
psi
D =
JG =
Iww =
175028027.34
158203.13
469214648.44
local
O.K.
GLOBAL BUCKLING
global
581261.79
lbs
global
769883.17
psi
33000
psi
Therefore, cr
global
global
29700.00
psi
global
11880.00
psi
fb =
2771.52
psi
Fb
D Calcs.
155925000
18900000
203027.34
psi in
psi in4
psi in6
Pcrglobal Calcs.
0.0190778
5262127
5.7900547
O.K.
JG Calcs.
105468.75
52734.375
Iww Calcs.
467775000.00
1218164.063
221484.375
Engineer's
Comment: Because
the /L ratio is so
high (1/455), SAY
OK.
=
=
=
=
Vinyl Ester
100
0.00
lbs
300.00
psf
10.00%
0.00%
Beam Properties
10
bw = Web Depth =
in.
7.00
psf
bf = Flange Width =
in.
psf
tf = Flange Thickness =
0.25
in.
Safety Factor =
307.00
2.5
tw = Web Thickness =
0.25
in
Length of Beam ( L ) =
1.50
ft
18.00
in
Tributary width =
3.00
ft
36.00
in
648.00
in2
Area =
Weight =
2.92
in
2.19
lb/ft
Sx =
4.03
in
Ix =
8.05
r =
1.66
Sy =
Iy =
r
Full Section EX
EC-LW (Web)
EC-LW (Flange)
EC-CW (Web)
EC-CW (Flange)
Gxy
L
J
CW
=
=
=
=
=
=
=
=
=
=
ft
Unbraced Length ( Lu ) =
4.50
18.00
in4
Max Deflection =
0.13
in
in
0.00
in
Warning Box
1.32
in
2.63
0.95
4.000E+06
2.800E+06
3.850E+06
1.900E+06
1.900E+06
5.E+05
18.00
0.063
10.52
Area Of Load =
S.F.
Applied Moment =
in
in
psi
psi
psi
psi
psi
psi
in
AW
k
A'
w
w
Fb
Fb1
fb
vxy
vyx
=
=
=
=
=
=
=
=
=
=
=
in4
6
in
Compressive Strength, Fc-flg-LW
Ultimate Beam Shear Strength, Fv-ult =
0.00
1.0000
1.0000
1.0000
921.00
76.75
33000
13200
771.31
0.35
0.12
52500
7000
lbs-in
2
in
in2
lbs/ft
lbs/in
psi Full Section Flexural Strength
psi
psi
psi
psi
=
=
=
=
=
Maximum Acting Shear Load =
Point Load M MAX
Unifrom Load M MAX
Applied M MAX
Total M MAX
Total Load
0.00
3108.38
0.00
3108.38
1381.50
690.75
lbs-in
lbs-in
lbs-in
lbs-in
lbs
lbs
Deflection =
0.0095
in
L / 1899.79
Note: The calculation for delfection is only for a Point Load and a
Uniform Load. The deflection for the Applied Moment is not
included.
3.00
2333.33
2100.00
2100.00
lbs
22340.61
psi
psi
O.K.
LOCAL BUCKLING
Critical Local
Buckling Stress scr =
b
z
p
q
=
=
=
=
If the calculated Local Buckling Stress above exceeds the Flange Compression Strength of the material, use cr
Therefore, cr
local
22340.61
20106.55
psi
Fb Local Buckling =
8042.62
psi
fb =
771.31
psi
D =
JG =
Iww =
34573437.50
31250.00
41193055.56
local
O.K.
GLOBAL BUCKLING
4
psi in
psi in4
psi in6
global
353368.28
lbs
global
394579.96
psi
33000
psi
Therefore, cr
global
global
29700.00
psi
global
11880.00
psi
771.31
psi
Fb
fb =
O.K.
D Calcs.
30800000
3733333.3
40104.167
JG Calcs.
20833.33333
10416.66667
Pcrglobal Calcs.
0.0529938
1039432.5
6.4151377
Iww Calcs.
41066666.67
106944.4444
19444.44444
=
=
=
=
Vinyl Ester
100
0.00
lbs
300.00
psf
10.00%
0.00%
Beam Properties
10
bw = Web Depth =
in.
10.00
psf
bf = Flange Width =
in.
psf
tf = Flange Thickness =
0.375
in.
Safety Factor =
310.00
2.5
tw = Web Thickness =
0.375
in
Length of Beam ( L ) =
4.50
ft
54.00
in
Tributary width =
2.13
ft
25.56
in
1380.24
in2
Area =
Weight =
6.57
in
4.92
lb/ft
Sx =
13.59
in
Ix =
40.76
r =
2.49
Sy =
Iy =
r
Full Section EX
EC-LW (Web)
EC-LW (Flange)
EC-CW (Web)
EC-CW (Flange)
Gxy
L
J
CW
=
=
=
=
=
=
=
=
=
=
ft
Unbraced Length ( Lu ) =
9.59
54.00
in4
Max Deflection =
0.13
in
in
0.00
in
Warning Box
4.44
in
13.32
1.42
4.000E+06
2.800E+06
3.850E+06
1.900E+06
1.900E+06
5.E+05
54.00
0.316
119.88
Area Of Load =
S.F.
Applied Moment =
in
in
psi
psi
psi
psi
psi
psi
in
AW
k
A'
w
w
Fb
Fb1
fb
vxy
vyx
=
=
=
=
=
=
=
=
=
=
=
in4
6
in
Compressive Strength, Fc-flg-LW
Ultimate Beam Shear Strength, Fv-ult =
0.00
2.2500
1.0000
2.2500
660.30
55.03
33000
13200
1475.84
0.35
0.12
52500
7000
lbs-in
2
in
in2
lbs/ft
lbs/in
psi Full Section Flexural Strength
psi
psi
psi
psi
=
=
=
=
=
Maximum Acting Shear Load =
Point Load M MAX
Unifrom Load M MAX
Applied M MAX
Total M MAX
Total Load
0.00
20056.61
0.00
20056.61
2971.35
1485.68
lbs-in
lbs-in
lbs-in
lbs-in
lbs
lbs
Deflection =
0.0552
in
L / 978.36
Note: The calculation for delfection is only for a Point Load and a
Uniform Load. The deflection for the Applied Moment is not
included.
3.00
2333.33
2100.00
4725.00
lbs
22340.61
psi
psi
O.K.
LOCAL BUCKLING
Critical Local
Buckling Stress scr =
b
z
p
q
=
=
=
=
If the calculated Local Buckling Stress above exceeds the Flange Compression Strength of the material, use cr
Therefore, cr
local
22340.61
20106.55
psi
Fb Local Buckling =
8042.62
psi
fb =
1475.84
psi
D =
JG =
Iww =
175028027.34
158203.13
469214648.44
local
O.K.
GLOBAL BUCKLING
global
102943.54
lbs
global
102261.79
psi
33000
psi
Therefore, cr
global
global
29700.00
psi
global
11880.00
psi
fb =
1475.84
psi
Fb
D Calcs.
155925000
18900000
203027.34
psi in
psi in4
psi in6
Pcrglobal Calcs.
0.0058882
5262127
3.3224235
O.K.
JG Calcs.
105468.75
52734.375
Iww Calcs.
467775000.00
1218164.063
221484.375
=
=
=
=
Vinyl Ester
100
0.00
lbs
300.00
psf
10.00%
0.00%
Beam Properties
10
bw = Web Depth =
in.
10.00
psf
bf = Flange Width =
in.
psf
tf = Flange Thickness =
0.375
in.
Safety Factor =
310.00
2.5
tw = Web Thickness =
0.375
in
Length of Beam ( L ) =
6.00
ft
72.00
in
Tributary width =
2.25
ft
27.00
in
1944.00
in2
Area =
Weight =
6.57
in
4.92
lb/ft
Sx =
13.59
in
Ix =
40.76
r =
2.49
Sy =
Iy =
r =
Full Section EX =
EC-LW (Web) =
EC-LW (Flange) =
EC-CW (Web) =
EC-CW (Flange) =
Gxy =
L =
J =
CW =
ft
Unbraced Length ( Lu ) =
13.50
30.00
in4
Max Deflection =
0.13
in
in
0.00
in
Warning Box
4.44
in
13.32
1.42
4.000E+06
2.800E+06
3.850E+06
1.900E+06
1.900E+06
5.E+05
72.00
0.316
119.88
Area Of Load =
S.F.
Applied Moment =
in
in
psi
psi
psi
psi
psi
psi
in
AW
k
A'
w
w
Fb
Fb1
fb
vxy
vyx
=
=
=
=
=
=
=
=
=
=
=
in4
6
in
Compressive Strength, Fc-flg-LW
Ultimate Beam Shear Strength, Fv-ult =
0.00
2.2500
1.0000
2.2500
697.50
58.13
33000
13200
2771.52
0.35
0.12
52500
7000
lbs-in
2
in
in2
lbs/ft
DEFLECTION IS OVER THE MAX
lbs/in
psi Full Section Flexural Strength
psi
psi
psi
psi
=
=
=
=
=
Maximum Acting Shear Load =
Point Load M MAX
Unifrom Load M MAX
Applied M MAX
Total M MAX
Total Load
0.00
37665.00
0.00
37665.00
4185.00
2092.50
lbs-in
lbs-in
lbs-in
lbs-in
lbs
lbs
Deflection =
0.1582
in
L / 455.04
Note: The calculation for delfection is only for a Point Load and a
Uniform Load. The deflection for the Applied Moment is not
included.
3.00
2333.33
2100.00
4725.00
lbs
22340.61
psi
psi
O.K.
LOCAL BUCKLING
Critical Local
Buckling Stress scr =
b
z
p
q
=
=
=
=
If the calculated Local Buckling Stress above exceeds the Flange Compression Strength of the material, use cr
Therefore, cr
local
22340.61
20106.55
psi
Fb Local Buckling =
8042.62
psi
fb =
2771.52
psi
D =
JG =
Iww =
175028027.34
158203.13
469214648.44
local
O.K.
GLOBAL BUCKLING
global
581261.79
lbs
global
769883.17
psi
33000
psi
Therefore, cr
global
global
29700.00
psi
global
11880.00
psi
fb =
2771.52
psi
Fb
D Calcs.
155925000
18900000
203027.34
psi in
psi in4
psi in6
Pcrglobal Calcs.
0.0190778
5262127
5.7900547
O.K.
JG Calcs.
105468.75
52734.375
Iww Calcs.
467775000.00
1218164.063
221484.375
Engineer's
Comment: Because
the /L ratio is so
high (1/455), SAY
OK.
=
=
=
=
Vinyl Ester
100
0.00
lbs
300.00
psf
10.00%
0.00%
Beam Properties
10
bw = Web Depth =
in.
10.00
psf
bf = Flange Width =
in.
psf
tf = Flange Thickness =
0.25
in.
Safety Factor =
310.00
2.5
tw = Web Thickness =
0.25
in
Length of Beam ( L ) =
1.50
ft
18.00
in
Tributary width =
3.00
ft
36.00
in
648.00
in2
Area =
Weight =
2.92
in
2.19
lb/ft
Sx =
4.03
in
Ix =
8.05
r =
1.66
Sy =
Iy =
r
Full Section EX
EC-LW (Web)
EC-LW (Flange)
EC-CW (Web)
EC-CW (Flange)
Gxy
L
J
CW
=
=
=
=
=
=
=
=
=
=
ft
Unbraced Length ( Lu ) =
4.50
18.00
in4
Max Deflection =
0.13
in
in
0.00
in
Warning Box
1.32
in
2.63
0.95
4.000E+06
2.800E+06
3.850E+06
1.900E+06
1.900E+06
5.E+05
18.00
0.063
10.52
Area Of Load =
S.F.
Applied Moment =
in
in
psi
psi
psi
psi
psi
psi
in
AW
k
A'
w
w
Fb
Fb1
fb
vxy
vyx
=
=
=
=
=
=
=
=
=
=
=
in4
6
in
Compressive Strength, Fc-flg-LW
Ultimate Beam Shear Strength, Fv-ult =
0.00
1.0000
1.0000
1.0000
930.00
77.50
33000
13200
778.85
0.35
0.12
52500
7000
lbs-in
2
in
in2
lbs/ft
lbs/in
psi Full Section Flexural Strength
psi
psi
psi
psi
=
=
=
=
=
Maximum Acting Shear Load =
Point Load M MAX
Unifrom Load M MAX
Applied M MAX
Total M MAX
Total Load
0.00
3138.75
0.00
3138.75
1395.00
697.50
lbs-in
lbs-in
lbs-in
lbs-in
lbs
lbs
Deflection =
0.0096
in
L / 1881.40
Note: The calculation for delfection is only for a Point Load and a
Uniform Load. The deflection for the Applied Moment is not
included.
3.00
2333.33
2100.00
2100.00
lbs
22340.61
psi
psi
O.K.
LOCAL BUCKLING
Critical Local
Buckling Stress scr =
b
z
p
q
=
=
=
=
If the calculated Local Buckling Stress above exceeds the Flange Compression Strength of the material, use cr
Therefore, cr
local
22340.61
20106.55
psi
Fb Local Buckling =
8042.62
psi
fb =
778.85
psi
D =
JG =
Iww =
34573437.50
31250.00
41193055.56
local
O.K.
GLOBAL BUCKLING
4
psi in
psi in4
psi in6
global
353368.28
lbs
global
394579.96
psi
33000
psi
Therefore, cr
global
global
29700.00
psi
global
11880.00
psi
778.85
psi
Fb
fb =
O.K.
D Calcs.
30800000
3733333.3
40104.167
JG Calcs.
20833.33333
10416.66667
Pcrglobal Calcs.
0.0529938
1039432.5
6.4151377
Iww Calcs.
41066666.67
106944.4444
19444.44444
=
=
=
=
Vinyl Ester
100
0.00
lbs
300.00
psf
10.00%
0.00%
Beam Properties
10
bw = Web Depth =
in.
10.00
psf
bf = Flange Width =
in.
psf
tf = Flange Thickness =
0.375
in.
Safety Factor =
310.00
2.5
tw = Web Thickness =
0.375
in
Length of Beam ( L ) =
4.50
ft
54.00
in
Tributary width =
2.13
ft
25.56
in
1380.24
in2
Area =
Weight =
6.57
in
4.92
lb/ft
Sx =
13.59
in
Ix =
40.76
r =
2.49
Sy =
Iy =
r
Full Section EX
EC-LW (Web)
EC-LW (Flange)
EC-CW (Web)
EC-CW (Flange)
Gxy
L
J
CW
=
=
=
=
=
=
=
=
=
=
ft
Unbraced Length ( Lu ) =
9.59
54.00
in4
Max Deflection =
0.13
in
in
0.00
in
Warning Box
4.44
in
13.32
1.42
4.000E+06
2.800E+06
3.850E+06
1.900E+06
1.900E+06
5.E+05
54.00
0.316
119.88
Area Of Load =
S.F.
Applied Moment =
in
in
psi
psi
psi
psi
psi
psi
in
AW
k
A'
w
w
Fb
Fb1
fb
vxy
vyx
=
=
=
=
=
=
=
=
=
=
=
in4
6
in
Compressive Strength, Fc-flg-LW
Ultimate Beam Shear Strength, Fv-ult =
0.00
2.2500
1.0000
2.2500
660.30
55.03
33000
13200
1475.84
0.35
0.12
52500
7000
lbs-in
2
in
in2
lbs/ft
lbs/in
psi Full Section Flexural Strength
psi
psi
psi
psi
=
=
=
=
=
Maximum Acting Shear Load =
Point Load M MAX
Unifrom Load M MAX
Applied M MAX
Total M MAX
Total Load
0.00
20056.61
0.00
20056.61
2971.35
1485.68
lbs-in
lbs-in
lbs-in
lbs-in
lbs
lbs
Deflection =
0.0552
in
L / 978.36
Note: The calculation for delfection is only for a Point Load and a
Uniform Load. The deflection for the Applied Moment is not
included.
3.00
2333.33
2100.00
4725.00
lbs
22340.61
psi
psi
O.K.
LOCAL BUCKLING
Critical Local
Buckling Stress scr =
b
z
p
q
=
=
=
=
If the calculated Local Buckling Stress above exceeds the Flange Compression Strength of the material, use cr
Therefore, cr
local
22340.61
20106.55
psi
Fb Local Buckling =
8042.62
psi
fb =
1475.84
psi
D =
JG =
Iww =
175028027.34
158203.13
469214648.44
local
O.K.
GLOBAL BUCKLING
global
102943.54
lbs
global
102261.79
psi
33000
psi
Therefore, cr
global
global
29700.00
psi
global
11880.00
psi
fb =
1475.84
psi
Fb
D Calcs.
155925000
18900000
203027.34
psi in
psi in4
psi in6
Pcrglobal Calcs.
0.0058882
5262127
3.3224235
O.K.
JG Calcs.
105468.75
52734.375
Iww Calcs.
467775000.00
1218164.063
221484.375
=
=
=
=
Vinyl Ester
100
0.00
lbs
300.00
psf
10.00%
0.00%
Beam Properties
10
bw = Web Depth =
in.
10.00
psf
bf = Flange Width =
in.
psf
tf = Flange Thickness =
0.375
in.
Safety Factor =
310.00
2.5
tw = Web Thickness =
0.375
in
Length of Beam ( L ) =
6.00
ft
72.00
in
Tributary width =
2.25
ft
27.00
in
1944.00
in2
Area =
Weight =
6.57
in
4.92
lb/ft
Sx =
13.59
in
Ix =
40.76
r =
2.49
Sy =
Iy =
r =
Full Section EX =
EC-LW (Web) =
EC-LW (Flange) =
EC-CW (Web) =
EC-CW (Flange) =
Gxy =
L =
J =
CW =
ft
Unbraced Length ( Lu ) =
13.50
30.00
in4
Max Deflection =
0.13
in
in
0.00
in
Warning Box
4.44
in
13.32
1.42
4.000E+06
2.800E+06
3.850E+06
1.900E+06
1.900E+06
5.E+05
72.00
0.316
119.88
Area Of Load =
S.F.
Applied Moment =
in
in
psi
psi
psi
psi
psi
psi
in
AW
k
A'
w
w
Fb
Fb1
fb
vxy
vyx
=
=
=
=
=
=
=
=
=
=
=
in4
6
in
Compressive Strength, Fc-flg-LW
Ultimate Beam Shear Strength, Fv-ult =
0.00
2.2500
1.0000
2.2500
697.50
58.13
33000
13200
2771.52
0.35
0.12
52500
7000
lbs-in
2
in
in2
lbs/ft
DEFLECTION IS OVER THE MAX
lbs/in
psi Full Section Flexural Strength
psi
psi
psi
psi
=
=
=
=
=
Maximum Acting Shear Load =
Point Load M MAX
Unifrom Load M MAX
Applied M MAX
Total M MAX
Total Load
0.00
37665.00
0.00
37665.00
4185.00
2092.50
lbs-in
lbs-in
lbs-in
lbs-in
lbs
lbs
Deflection =
0.1582
in
L / 455.04
Note: The calculation for delfection is only for a Point Load and a
Uniform Load. The deflection for the Applied Moment is not
included.
3.00
2333.33
2100.00
4725.00
lbs
22340.61
psi
psi
O.K.
LOCAL BUCKLING
Critical Local
Buckling Stress scr =
b
z
p
q
=
=
=
=
If the calculated Local Buckling Stress above exceeds the Flange Compression Strength of the material, use cr
Therefore, cr
local
22340.61
20106.55
psi
Fb Local Buckling =
8042.62
psi
fb =
2771.52
psi
D =
JG =
Iww =
175028027.34
158203.13
469214648.44
local
O.K.
GLOBAL BUCKLING
global
581261.79
lbs
global
769883.17
psi
33000
psi
Therefore, cr
global
global
29700.00
psi
global
11880.00
psi
fb =
2771.52
psi
Fb
D Calcs.
155925000
18900000
203027.34
psi in
psi in4
psi in6
Pcrglobal Calcs.
0.0190778
5262127
5.7900547
O.K.
JG Calcs.
105468.75
52734.375
Iww Calcs.
467775000.00
1218164.063
221484.375
Engineer's
Comment: Because
the /L ratio is so
high (1/455), SAY
OK.
=
=
=
=
Vinyl Ester
100
0.00
lbs
300.00
psf
10.00%
0.00%
Beam Properties
10
bw = Web Depth =
in.
10.00
psf
bf = Flange Width =
in.
psf
tf = Flange Thickness =
0.25
in.
Safety Factor =
310.00
2.5
tw = Web Thickness =
0.25
in
Length of Beam ( L ) =
1.50
ft
18.00
in
Tributary width =
3.00
ft
36.00
in
648.00
in2
Area =
Weight =
2.92
in
2.19
lb/ft
Sx =
4.03
in
Ix =
8.05
r =
1.66
Sy =
Iy =
r
Full Section EX
EC-LW (Web)
EC-LW (Flange)
EC-CW (Web)
EC-CW (Flange)
Gxy
L
J
CW
=
=
=
=
=
=
=
=
=
=
ft
Unbraced Length ( Lu ) =
4.50
18.00
in4
Max Deflection =
0.13
in
in
0.00
in
Warning Box
1.32
in
2.63
0.95
4.000E+06
2.800E+06
3.850E+06
1.900E+06
1.900E+06
5.E+05
18.00
0.063
10.52
Area Of Load =
S.F.
Applied Moment =
in
in
psi
psi
psi
psi
psi
psi
in
AW
k
A'
w
w
Fb
Fb1
fb
vxy
vyx
=
=
=
=
=
=
=
=
=
=
=
in4
6
in
Compressive Strength, Fc-flg-LW
Ultimate Beam Shear Strength, Fv-ult =
0.00
1.0000
1.0000
1.0000
930.00
77.50
33000
13200
778.85
0.35
0.12
52500
7000
lbs-in
2
in
in2
lbs/ft
lbs/in
psi Full Section Flexural Strength
psi
psi
psi
psi
=
=
=
=
=
Maximum Acting Shear Load =
Point Load M MAX
Unifrom Load M MAX
Applied M MAX
Total M MAX
Total Load
0.00
3138.75
0.00
3138.75
1395.00
697.50
lbs-in
lbs-in
lbs-in
lbs-in
lbs
lbs
Deflection =
0.0096
in
L / 1881.40
Note: The calculation for delfection is only for a Point Load and a
Uniform Load. The deflection for the Applied Moment is not
included.
3.00
2333.33
2100.00
2100.00
lbs
22340.61
psi
psi
O.K.
LOCAL BUCKLING
Critical Local
Buckling Stress scr =
b
z
p
q
=
=
=
=
If the calculated Local Buckling Stress above exceeds the Flange Compression Strength of the material, use cr
Therefore, cr
local
22340.61
20106.55
psi
Fb Local Buckling =
8042.62
psi
fb =
778.85
psi
D =
JG =
Iww =
34573437.50
31250.00
41193055.56
local
O.K.
GLOBAL BUCKLING
4
psi in
psi in4
psi in6
global
353368.28
lbs
global
394579.96
psi
33000
psi
Therefore, cr
global
global
29700.00
psi
global
11880.00
psi
778.85
psi
Fb
fb =
O.K.
D Calcs.
30800000
3733333.3
40104.167
JG Calcs.
20833.33333
10416.66667
Pcrglobal Calcs.
0.0529938
1039432.5
6.4151377
Iww Calcs.
41066666.67
106944.4444
19444.44444
=
=
=
=
Vinyl Ester
100
0.00
lbs
300.00
psf
10.00%
0.00%
Beam Properties
10
bw = Web Depth =
in.
10.00
psf
bf = Flange Width =
in.
psf
tf = Flange Thickness =
0.375
in.
Safety Factor =
310.00
2.5
tw = Web Thickness =
0.375
in
Length of Beam ( L ) =
4.50
ft
54.00
in
Tributary width =
2.13
ft
25.56
in
1380.24
in2
Area =
Weight =
6.57
in
4.92
lb/ft
Sx =
13.59
in
Ix =
40.76
r =
2.49
Sy =
Iy =
r
Full Section EX
EC-LW (Web)
EC-LW (Flange)
EC-CW (Web)
EC-CW (Flange)
Gxy
L
J
CW
=
=
=
=
=
=
=
=
=
=
ft
Unbraced Length ( Lu ) =
9.59
54.00
in4
Max Deflection =
0.13
in
in
0.00
in
Warning Box
4.44
in
13.32
1.42
4.000E+06
2.800E+06
3.850E+06
1.900E+06
1.900E+06
5.E+05
54.00
0.316
119.88
Area Of Load =
S.F.
Applied Moment =
in
in
psi
psi
psi
psi
psi
psi
in
AW
k
A'
w
w
Fb
Fb1
fb
vxy
vyx
=
=
=
=
=
=
=
=
=
=
=
in4
6
in
Compressive Strength, Fc-flg-LW
Ultimate Beam Shear Strength, Fv-ult =
0.00
2.2500
1.0000
2.2500
660.30
55.03
33000
13200
1475.84
0.35
0.12
52500
7000
lbs-in
2
in
in2
lbs/ft
lbs/in
psi Full Section Flexural Strength
psi
psi
psi
psi
=
=
=
=
=
Maximum Acting Shear Load =
Point Load M MAX
Unifrom Load M MAX
Applied M MAX
Total M MAX
Total Load
0.00
20056.61
0.00
20056.61
2971.35
1485.68
lbs-in
lbs-in
lbs-in
lbs-in
lbs
lbs
Deflection =
0.0552
in
L / 978.36
Note: The calculation for delfection is only for a Point Load and a
Uniform Load. The deflection for the Applied Moment is not
included.
3.00
2333.33
2100.00
4725.00
lbs
22340.61
psi
psi
O.K.
LOCAL BUCKLING
Critical Local
Buckling Stress scr =
b
z
p
q
=
=
=
=
If the calculated Local Buckling Stress above exceeds the Flange Compression Strength of the material, use cr
Therefore, cr
local
22340.61
20106.55
psi
Fb Local Buckling =
8042.62
psi
fb =
1475.84
psi
D =
JG =
Iww =
175028027.34
158203.13
469214648.44
local
O.K.
GLOBAL BUCKLING
global
102943.54
lbs
global
102261.79
psi
33000
psi
Therefore, cr
global
global
29700.00
psi
global
11880.00
psi
fb =
1475.84
psi
Fb
D Calcs.
155925000
18900000
203027.34
psi in
psi in4
psi in6
Pcrglobal Calcs.
0.0058882
5262127
3.3224235
O.K.
JG Calcs.
105468.75
52734.375
Iww Calcs.
467775000.00
1218164.063
221484.375
=
=
=
=
Vinyl Ester
100
0.00
lbs
300.00
psf
10.00%
0.00%
Beam Properties
10
bw = Web Depth =
in.
10.00
psf
bf = Flange Width =
in.
psf
tf = Flange Thickness =
0.375
in.
Safety Factor =
310.00
2.5
tw = Web Thickness =
0.375
in
Length of Beam ( L ) =
6.00
ft
72.00
in
Tributary width =
2.25
ft
27.00
in
1944.00
in2
Area =
Weight =
6.57
in
4.92
lb/ft
Sx =
13.59
in
Ix =
40.76
r =
2.49
Sy =
Iy =
r =
Full Section EX =
EC-LW (Web) =
EC-LW (Flange) =
EC-CW (Web) =
EC-CW (Flange) =
Gxy =
L =
J =
CW =
ft
Unbraced Length ( Lu ) =
13.50
72.00
in4
Max Deflection =
0.13
in
in
0.00
in
Warning Box
4.44
in
13.32
1.42
4.000E+06
2.800E+06
3.850E+06
1.900E+06
1.900E+06
5.E+05
72.00
0.316
119.88
Area Of Load =
S.F.
Applied Moment =
in
in
psi
psi
psi
psi
psi
psi
in
AW
k
A'
w
w
Fb
Fb1
fb
vxy
vyx
=
=
=
=
=
=
=
=
=
=
=
in4
6
in
Compressive Strength, Fc-flg-LW
Ultimate Beam Shear Strength, Fv-ult =
0.00
2.2500
1.0000
2.2500
697.50
58.13
33000
13200
2771.52
0.35
0.12
52500
7000
lbs-in
2
in
in2
lbs/ft
DEFLECTION IS OVER THE MAX
lbs/in
psi Full Section Flexural Strength
psi
psi
psi
psi
=
=
=
=
=
Maximum Acting Shear Load =
Point Load M MAX
Unifrom Load M MAX
Applied M MAX
Total M MAX
Total Load
0.00
37665.00
0.00
37665.00
4185.00
2092.50
lbs-in
lbs-in
lbs-in
lbs-in
lbs
lbs
Deflection =
0.1582
in
L / 455.04
Note: The calculation for delfection is only for a Point Load and a
Uniform Load. The deflection for the Applied Moment is not
included.
3.00
2333.33
2100.00
4725.00
lbs
22340.61
psi
psi
O.K.
LOCAL BUCKLING
Critical Local
Buckling Stress scr =
b
z
p
q
=
=
=
=
If the calculated Local Buckling Stress above exceeds the Flange Compression Strength of the material, use cr
Therefore, cr
local
22340.61
20106.55
psi
Fb Local Buckling =
8042.62
psi
fb =
2771.52
psi
D =
JG =
Iww =
175028027.34
158203.13
469214648.44
local
O.K.
GLOBAL BUCKLING
global
44933.29
lbs
global
59514.29
psi
33000
psi
Therefore, cr
global
global
29700.00
psi
global
11880.00
psi
fb =
2771.52
psi
Fb
D Calcs.
155925000
18900000
203027.34
psi in
psi in4
psi in6
Pcrglobal Calcs.
0.0033121
5262127
2.5781107
O.K.
JG Calcs.
105468.75
52734.375
Iww Calcs.
467775000.00
1218164.063
221484.375
Engineer's
Comment: Because
the /L ratio is so
high (1/455), SAY
OK.
=
=
=
=
Vinyl Ester
100
0.00
lbs
300.00
psf
10.00%
0.00%
Beam Properties
10
bw = Web Depth =
in.
10.00
psf
bf = Flange Width =
in.
psf
tf = Flange Thickness =
0.25
in.
Safety Factor =
310.00
2.5
tw = Web Thickness =
0.25
in
Length of Beam ( L ) =
1.50
ft
18.00
in
Tributary width =
3.00
ft
36.00
in
648.00
in2
Area =
Weight =
2.92
in
2.19
lb/ft
Sx =
4.03
in
Ix =
8.05
r =
1.66
Sy =
Iy =
r
Full Section EX
EC-LW (Web)
EC-LW (Flange)
EC-CW (Web)
EC-CW (Flange)
Gxy
L
J
CW
=
=
=
=
=
=
=
=
=
=
ft
Unbraced Length ( Lu ) =
4.50
18.00
in4
Max Deflection =
0.13
in
in
0.00
in
Warning Box
1.32
in
2.63
0.95
4.000E+06
2.800E+06
3.850E+06
1.900E+06
1.900E+06
5.E+05
18.00
0.063
10.52
Area Of Load =
S.F.
Applied Moment =
in
in
psi
psi
psi
psi
psi
psi
in
AW
k
A'
w
w
Fb
Fb1
fb
vxy
vyx
=
=
=
=
=
=
=
=
=
=
=
in4
6
in
Compressive Strength, Fc-flg-LW
Ultimate Beam Shear Strength, Fv-ult =
0.00
1.0000
1.0000
1.0000
930.00
77.50
33000
13200
778.85
0.35
0.12
52500
7000
lbs-in
2
in
in2
lbs/ft
lbs/in
psi Full Section Flexural Strength
psi
psi
psi
psi
=
=
=
=
=
Maximum Acting Shear Load =
Point Load M MAX
Unifrom Load M MAX
Applied M MAX
Total M MAX
Total Load
0.00
3138.75
0.00
3138.75
1395.00
697.50
lbs-in
lbs-in
lbs-in
lbs-in
lbs
lbs
Deflection =
0.0096
in
L / 1881.40
Note: The calculation for delfection is only for a Point Load and a
Uniform Load. The deflection for the Applied Moment is not
included.
3.00
2333.33
2100.00
2100.00
lbs
22340.61
psi
psi
O.K.
LOCAL BUCKLING
Critical Local
Buckling Stress scr =
b
z
p
q
=
=
=
=
If the calculated Local Buckling Stress above exceeds the Flange Compression Strength of the material, use cr
Therefore, cr
local
22340.61
20106.55
psi
Fb Local Buckling =
8042.62
psi
fb =
778.85
psi
D =
JG =
Iww =
34573437.50
31250.00
41193055.56
local
O.K.
GLOBAL BUCKLING
4
psi in
psi in4
psi in6
global
353368.28
lbs
global
394579.96
psi
33000
psi
Therefore, cr
global
global
29700.00
psi
global
11880.00
psi
778.85
psi
Fb
fb =
O.K.
D Calcs.
30800000
3733333.3
40104.167
JG Calcs.
20833.33333
10416.66667
Pcrglobal Calcs.
0.0529938
1039432.5
6.4151377
Iww Calcs.
41066666.67
106944.4444
19444.44444
=
=
=
=
Vinyl Ester
100
0.00
lbs
300.00
psf
10.00%
0.00%
Beam Properties
10
bw = Web Depth =
in.
10.00
psf
bf = Flange Width =
in.
psf
tf = Flange Thickness =
0.375
in.
Safety Factor =
310.00
2.5
tw = Web Thickness =
0.375
in
Length of Beam ( L ) =
4.50
ft
54.00
in
Tributary width =
2.13
ft
25.56
in
1380.24
in2
Area =
Weight =
6.57
in
4.92
lb/ft
Sx =
13.59
in
Ix =
40.76
r =
2.49
Sy =
Iy =
r
Full Section EX
EC-LW (Web)
EC-LW (Flange)
EC-CW (Web)
EC-CW (Flange)
Gxy
L
J
CW
=
=
=
=
=
=
=
=
=
=
ft
Unbraced Length ( Lu ) =
9.59
54.00
in4
Max Deflection =
0.13
in
in
0.00
in
Warning Box
4.44
in
13.32
1.42
4.000E+06
2.800E+06
3.850E+06
1.900E+06
1.900E+06
5.E+05
54.00
0.316
119.88
Area Of Load =
S.F.
Applied Moment =
in
in
psi
psi
psi
psi
psi
psi
in
AW
k
A'
w
w
Fb
Fb1
fb
vxy
vyx
=
=
=
=
=
=
=
=
=
=
=
in4
6
in
Compressive Strength, Fc-flg-LW
Ultimate Beam Shear Strength, Fv-ult =
0.00
2.2500
1.0000
2.2500
660.30
55.03
33000
13200
1475.84
0.35
0.12
52500
7000
lbs-in
2
in
in2
lbs/ft
lbs/in
psi Full Section Flexural Strength
psi
psi
psi
psi
=
=
=
=
=
Maximum Acting Shear Load =
Point Load M MAX
Unifrom Load M MAX
Applied M MAX
Total M MAX
Total Load
0.00
20056.61
0.00
20056.61
2971.35
1485.68
lbs-in
lbs-in
lbs-in
lbs-in
lbs
lbs
Deflection =
0.0552
in
L / 978.36
Note: The calculation for delfection is only for a Point Load and a
Uniform Load. The deflection for the Applied Moment is not
included.
3.00
2333.33
2100.00
4725.00
lbs
22340.61
psi
psi
O.K.
LOCAL BUCKLING
Critical Local
Buckling Stress scr =
b
z
p
q
=
=
=
=
If the calculated Local Buckling Stress above exceeds the Flange Compression Strength of the material, use cr
Therefore, cr
local
22340.61
20106.55
psi
Fb Local Buckling =
8042.62
psi
fb =
1475.84
psi
D =
JG =
Iww =
175028027.34
158203.13
469214648.44
local
O.K.
GLOBAL BUCKLING
global
102943.54
lbs
global
102261.79
psi
33000
psi
Therefore, cr
global
global
29700.00
psi
global
11880.00
psi
fb =
1475.84
psi
Fb
D Calcs.
155925000
18900000
203027.34
psi in
psi in4
psi in6
Pcrglobal Calcs.
0.0058882
5262127
3.3224235
O.K.
JG Calcs.
105468.75
52734.375
Iww Calcs.
467775000.00
1218164.063
221484.375
=
=
=
=
Vinyl Ester
100
0.00
lbs
300.00
psf
10.00%
0.00%
Beam Properties
10
bw = Web Depth =
in.
10.00
psf
bf = Flange Width =
in.
psf
tf = Flange Thickness =
0.375
in.
Safety Factor =
310.00
2.5
tw = Web Thickness =
0.375
in
Length of Beam ( L ) =
6.00
ft
72.00
in
Tributary width =
2.25
ft
27.00
in
1944.00
in2
Area =
Weight =
6.57
in
4.92
lb/ft
Sx =
13.59
in
Ix =
40.76
r =
2.49
Sy =
Iy =
r =
Full Section EX =
EC-LW (Web) =
EC-LW (Flange) =
EC-CW (Web) =
EC-CW (Flange) =
Gxy =
L =
J =
CW =
ft
Unbraced Length ( Lu ) =
13.50
72.00
in4
Max Deflection =
0.13
in
in
0.00
in
Warning Box
4.44
in
13.32
1.42
4.000E+06
2.800E+06
3.850E+06
1.900E+06
1.900E+06
5.E+05
72.00
0.316
119.88
Area Of Load =
S.F.
Applied Moment =
in
in
psi
psi
psi
psi
psi
psi
in
AW
k
A'
w
w
Fb
Fb1
fb
vxy
vyx
=
=
=
=
=
=
=
=
=
=
=
in4
6
in
Compressive Strength, Fc-flg-LW
Ultimate Beam Shear Strength, Fv-ult =
0.00
2.2500
1.0000
2.2500
697.50
58.13
33000
13200
2771.52
0.35
0.12
52500
7000
lbs-in
2
in
in2
lbs/ft
DEFLECTION IS OVER THE MAX
lbs/in
psi Full Section Flexural Strength
psi
psi
psi
psi
=
=
=
=
=
Maximum Acting Shear Load =
Point Load M MAX
Unifrom Load M MAX
Applied M MAX
Total M MAX
Total Load
0.00
37665.00
0.00
37665.00
4185.00
2092.50
lbs-in
lbs-in
lbs-in
lbs-in
lbs
lbs
Deflection =
0.1582
in
L / 455.04
Note: The calculation for delfection is only for a Point Load and a
Uniform Load. The deflection for the Applied Moment is not
included.
3.00
2333.33
2100.00
4725.00
lbs
22340.61
psi
psi
O.K.
LOCAL BUCKLING
Critical Local
Buckling Stress scr =
b
z
p
q
=
=
=
=
If the calculated Local Buckling Stress above exceeds the Flange Compression Strength of the material, use cr
Therefore, cr
local
22340.61
20106.55
psi
Fb Local Buckling =
8042.62
psi
fb =
2771.52
psi
D =
JG =
Iww =
175028027.34
158203.13
469214648.44
local
O.K.
GLOBAL BUCKLING
global
44933.29
lbs
global
59514.29
psi
33000
psi
Therefore, cr
global
global
29700.00
psi
global
11880.00
psi
fb =
2771.52
psi
Fb
D Calcs.
155925000
18900000
203027.34
psi in
psi in4
psi in6
Pcrglobal Calcs.
0.0033121
5262127
2.5781107
O.K.
JG Calcs.
105468.75
52734.375
Iww Calcs.
467775000.00
1218164.063
221484.375
Engineer's
Comment: Because
the /L ratio is so
high (1/455), SAY
OK.
=
=
=
=
Vinyl Ester
100
0.00
lbs
300.00
psf
10.00%
0.00%
Beam Properties
10
bw = Web Depth =
in.
10.00
psf
bf = Flange Width =
in.
psf
tf = Flange Thickness =
0.25
in.
Safety Factor =
310.00
2.5
tw = Web Thickness =
0.25
in
Length of Beam ( L ) =
1.50
ft
18.00
Tributary width =
3.00
ft
36.00
in
648.00
in2
Area =
Weight =
2.92
in
2.19
lb/ft
Sx =
4.03
in
Ix =
8.05
in4
r =
1.66
in
Sy =
Iy =
r
Full Section EX
EC-LW (Web)
EC-LW (Flange)
EC-CW (Web)
EC-CW (Flange)
Gxy
L
J
CW
=
=
=
=
=
=
=
=
=
=
ft
Unbraced Length ( Lu ) =
4.50
18.00
Max Deflection =
0.13
in
0.00
in
in
Warning Box
1.32
in
2.63
0.95
4.000E+06
2.800E+06
3.850E+06
1.900E+06
1.900E+06
5.E+05
18.00
0.063
10.52
Area Of Load =
S.F.
Applied Moment =
in
in
psi
psi
psi
psi
psi
psi
in
AW
k
A'
w
w
Fb
Fb1
fb
vxy
vyx
=
=
=
=
=
=
=
=
=
=
=
in4
in6
Compressive Strength, Fc-flg-LW
Ultimate Beam Shear Strength, Fv-ult =
0.00
1.0000
1.0000
1.0000
930.00
77.50
33000
13200
778.85
0.35
0.12
52500
7000
lbs-in
in2
in2
lbs/ft
lbs/in
psi Full Section Flexural Strength
psi
psi
psi
psi
=
=
=
=
=
Maximum Acting Shear Load =
Point Load M MAX
Unifrom Load M MAX
Applied M MAX
Total M MAX
Total Load
0.00
3138.75
0.00
3138.75
1395.00
697.50
lbs-in
lbs-in
lbs-in
lbs-in
lbs
lbs
Deflection =
0.0096
in
L / 1881.40
Note: The calculation for delfection is only for a Point Load and a
Uniform Load. The deflection for the Applied Moment is not
included.
3.00
2333.33
2100.00
2100.00
lbs
22340.61
psi
psi
O.K.
LOCAL BUCKLING
Critical Local
Buckling Stress scr =
b
z
p
q
=
=
=
=
If the calculated Local Buckling Stress above exceeds the Flange Compression Strength of the material, use cr
Therefore, cr
local
22340.61
20106.55
psi
Fb Local Buckling =
8042.62
psi
fb =
778.85
psi
D =
JG =
Iww =
34573437.50
31250.00
41193055.56
local
O.K.
GLOBAL BUCKLING
4
psi in
psi in4
psi in6
global
353368.28
lbs
global
394579.96
psi
33000
psi
Therefore, cr
global
global
29700.00
psi
global
11880.00
psi
778.85
psi
Fb
fb =
D Calcs.
30800000
3733333.3
40104.167
JG Calcs.
20833.33333
10416.66667
global
Iww Calcs.
41066666.67
106944.4444
19444.44444
Pcr
Calcs.
0.0529938
1039432.5
6.4151377
O.K.
=
=
=
=
Vinyl Ester
100
0.00
lbs
10
300.00
psf
10.00%
bw = Web Depth =
in.
10.00
psf
0.00%
bf = Flange Width =
in.
310.00
2.5
psf
Beam Properties
tf = Flange Thickness =
0.375
in.
Safety Factor =
tw = Web Thickness =
0.375
in
Length of Beam ( L ) =
4.50
ft
54.00
Tributary width =
2.13
ft
25.56
in
1380.24
in2
Area =
Weight =
6.57
in
4.92
lb/ft
Sx =
13.59
in
Ix =
40.76
in4
r =
2.49
in
Sy =
Iy =
r
Full Section EX
EC-LW (Web)
EC-LW (Flange)
EC-CW (Web)
EC-CW (Flange)
Gxy
L
J
CW
=
=
=
=
=
=
=
=
=
=
ft
Unbraced Length ( Lu ) =
9.59
54.00
Max Deflection =
0.13
in
0.00
in
in
Warning Box
4.44
in
13.32
1.42
4.000E+06
2.800E+06
3.850E+06
1.900E+06
1.900E+06
5.E+05
54.00
0.316
119.88
Area Of Load =
S.F.
Applied Moment =
in
in
psi
psi
psi
psi
psi
psi
in
AW
k
A'
w
w
Fb
Fb1
fb
vxy
vyx
=
=
=
=
=
=
=
=
=
=
=
in4
in6
Compressive Strength, Fc-flg-LW
Ultimate Beam Shear Strength, Fv-ult =
0.00
2.2500
1.0000
2.2500
660.30
55.03
33000
13200
1475.84
0.35
0.12
52500
7000
lbs-in
in2
in2
lbs/ft
lbs/in
psi Full Section Flexural Strength
psi
psi
psi
psi
=
=
=
=
=
Maximum Acting Shear Load =
Point Load M MAX
Unifrom Load M MAX
Applied M MAX
Total M MAX
Total Load
0.00
20056.61
0.00
20056.61
2971.35
1485.68
lbs-in
lbs-in
lbs-in
lbs-in
lbs
lbs
Deflection =
0.0552
in
L / 978.36
Note: The calculation for delfection is only for a Point Load and a
Uniform Load. The deflection for the Applied Moment is not
included.
3.00
2333.33
2100.00
4725.00
lbs
22340.61
psi
psi
O.K.
LOCAL BUCKLING
Critical Local
Buckling Stress scr =
b
z
p
q
=
=
=
=
If the calculated Local Buckling Stress above exceeds the Flange Compression Strength of the material, use cr
Therefore, cr
local
22340.61
20106.55
psi
Fb Local Buckling =
8042.62
psi
fb =
1475.84
psi
D =
JG =
Iww =
175028027.34
158203.13
469214648.44
local
O.K.
GLOBAL BUCKLING
4
psi in
psi in4
psi in6
global
102943.54
global
102261.79
psi
33000
psi
29700.00
psi
11880.00
psi
fb =
1475.84
psi
Therefore, cr
global
global
lbs
D Calcs.
155925000
18900000
203027.34
JG Calcs.
105468.75
52734.375
global
Iww Calcs.
467775000.00
1218164.063
221484.375
Pcr
Calcs.
0.0058882
5262127
3.3224235
O.K.
=
=
=
=
Vinyl Ester
100
0.00
lbs
300.00
psf
10.00%
0.00%
Beam Properties
10
bw = Web Depth =
in.
10.00
psf
bf = Flange Width =
in.
psf
tf = Flange Thickness =
0.375
in.
Safety Factor =
310.00
2.5
tw = Web Thickness =
0.375
in
Length of Beam ( L ) =
6.00
ft
72.00
in
Tributary width =
2.25
ft
27.00
in
1944.00
in2
Area =
Weight =
6.57
in
4.92
lb/ft
Sx =
13.59
in
Ix =
40.76
r =
2.49
Sy =
Iy =
r =
Full Section EX =
EC-LW (Web) =
EC-LW (Flange) =
EC-CW (Web) =
EC-CW (Flange) =
Gxy =
L =
J =
CW =
ft
Unbraced Length ( Lu ) =
13.50
36.00
in4
Max Deflection =
0.13
in
in
0.00
in
Warning Box
4.44
in
13.32
1.42
4.000E+06
2.800E+06
3.850E+06
1.900E+06
1.900E+06
5.E+05
72.00
0.316
119.88
Area Of Load =
S.F.
Applied Moment =
in
in
psi
psi
psi
psi
psi
psi
in
AW
k
A'
w
w
Fb
Fb1
fb
vxy
vyx
=
=
=
=
=
=
=
=
=
=
=
in4
6
in
Compressive Strength, Fc-flg-LW
Ultimate Beam Shear Strength, Fv-ult =
0.00
2.2500
1.0000
2.2500
697.50
58.13
33000
13200
2771.52
0.35
0.12
52500
7000
lbs-in
2
in
in2
lbs/ft
DEFLECTION IS OVER THE MAX
lbs/in
psi Full Section Flexural Strength
psi
psi
psi
psi
=
=
=
=
=
Maximum Acting Shear Load =
Point Load M MAX
Unifrom Load M MAX
Applied M MAX
Total M MAX
Total Load
0.00
37665.00
0.00
37665.00
4185.00
2092.50
lbs-in
lbs-in
lbs-in
lbs-in
lbs
lbs
Deflection =
0.1582
in
L / 455.04
Note: The calculation for delfection is only for a Point Load and a
Uniform Load. The deflection for the Applied Moment is not
included.
3.00
2333.33
2100.00
4725.00
lbs
22340.61
psi
psi
O.K.
LOCAL BUCKLING
Critical Local
Buckling Stress scr =
b
z
p
q
=
=
=
=
If the calculated Local Buckling Stress above exceeds the Flange Compression Strength of the material, use cr
Therefore, cr
local
22340.61
20106.55
psi
Fb Local Buckling =
8042.62
psi
fb =
2771.52
psi
D =
JG =
Iww =
175028027.34
158203.13
469214648.44
local
O.K.
GLOBAL BUCKLING
global
338578.58
lbs
global
448448.45
psi
33000
psi
Therefore, cr
global
global
29700.00
psi
global
11880.00
psi
fb =
2771.52
psi
Fb
D Calcs.
155925000
18900000
203027.34
psi in
psi in4
psi in6
Pcrglobal Calcs.
0.0132485
5262127
4.8566058
O.K.
JG Calcs.
105468.75
52734.375
Iww Calcs.
467775000.00
1218164.063
221484.375
Engineer's
Comment: Because
the /L ratio is so
high (1/455), SAY
OK.
=
=
=
=
Vinyl Ester
100
0.00
lbs
300.00
psf
10.00%
0.00%
Beam Properties
10
bw = Web Depth =
in.
10.00
psf
bf = Flange Width =
in.
psf
tf = Flange Thickness =
0.25
in.
Safety Factor =
310.00
2.5
tw = Web Thickness =
0.25
in
Length of Beam ( L ) =
1.50
ft
18.00
in
Tributary width =
3.00
ft
36.00
in
648.00
in2
Area =
Weight =
2.92
in
2.19
lb/ft
Sx =
4.03
in
Ix =
8.05
r =
1.66
Sy =
Iy =
r
Full Section EX
EC-LW (Web)
EC-LW (Flange)
EC-CW (Web)
EC-CW (Flange)
Gxy
L
J
CW
=
=
=
=
=
=
=
=
=
=
ft
Unbraced Length ( Lu ) =
4.50
18.00
in4
Max Deflection =
0.13
in
in
0.00
in
Warning Box
1.32
in
2.63
0.95
4.000E+06
2.800E+06
3.850E+06
1.900E+06
1.900E+06
5.E+05
18.00
0.063
10.52
Area Of Load =
S.F.
Applied Moment =
in
in
psi
psi
psi
psi
psi
psi
in
AW
k
A'
w
w
Fb
Fb1
fb
vxy
vyx
=
=
=
=
=
=
=
=
=
=
=
in4
6
in
Compressive Strength, Fc-flg-LW
Ultimate Beam Shear Strength, Fv-ult =
0.00
1.0000
1.0000
1.0000
930.00
77.50
33000
13200
778.85
0.35
0.12
52500
7000
lbs-in
2
in
in2
lbs/ft
lbs/in
psi Full Section Flexural Strength
psi
psi
psi
psi
=
=
=
=
=
Maximum Acting Shear Load =
Point Load M MAX
Unifrom Load M MAX
Applied M MAX
Total M MAX
Total Load
0.00
3138.75
0.00
3138.75
1395.00
697.50
lbs-in
lbs-in
lbs-in
lbs-in
lbs
lbs
Deflection =
0.0096
in
L / 1881.40
Note: The calculation for delfection is only for a Point Load and a
Uniform Load. The deflection for the Applied Moment is not
included.
3.00
2333.33
2100.00
2100.00
lbs
22340.61
psi
psi
O.K.
LOCAL BUCKLING
Critical Local
Buckling Stress scr =
b
z
p
q
=
=
=
=
If the calculated Local Buckling Stress above exceeds the Flange Compression Strength of the material, use cr
Therefore, cr
local
22340.61
20106.55
psi
Fb Local Buckling =
8042.62
psi
fb =
778.85
psi
D =
JG =
Iww =
34573437.50
31250.00
41193055.56
local
O.K.
GLOBAL BUCKLING
4
psi in
psi in4
psi in6
global
353368.28
lbs
global
394579.96
psi
33000
psi
Therefore, cr
global
global
29700.00
psi
global
11880.00
psi
778.85
psi
Fb
fb =
O.K.
D Calcs.
30800000
3733333.3
40104.167
JG Calcs.
20833.33333
10416.66667
Pcrglobal Calcs.
0.0529938
1039432.5
6.4151377
Iww Calcs.
41066666.67
106944.4444
19444.44444
=
=
=
=
Vinyl Ester
100
0.00
lbs
300.00
psf
10.00%
0.00%
Beam Properties
10
bw = Web Depth =
in.
10.00
psf
bf = Flange Width =
in.
psf
tf = Flange Thickness =
0.375
in.
Safety Factor =
310.00
2.5
tw = Web Thickness =
0.375
in
Length of Beam ( L ) =
5.00
ft
60.00
in
Tributary width =
1.88
ft
22.50
in
1350.00
in2
Area =
Weight =
6.57
in
4.92
lb/ft
Sx =
13.59
in
Ix =
40.76
r =
2.49
Sy =
Iy =
r
Full Section EX
EC-LW (Web)
EC-LW (Flange)
EC-CW (Web)
EC-CW (Flange)
Gxy
L
J
CW
=
=
=
=
=
=
=
=
=
=
ft
Unbraced Length ( Lu ) =
9.38
60.00
in4
Max Deflection =
0.13
in
in
0.00
in
Warning Box
4.44
in
13.32
1.42
4.000E+06
2.800E+06
3.850E+06
1.900E+06
1.900E+06
5.E+05
60.00
0.316
119.88
Area Of Load =
S.F.
Applied Moment =
in
in
psi
psi
psi
psi
psi
psi
in
AW
k
A'
w
w
Fb
Fb1
fb
vxy
vyx
=
=
=
=
=
=
=
=
=
=
=
in4
6
in
Compressive Strength, Fc-flg-LW
Ultimate Beam Shear Strength, Fv-ult =
0.00
2.2500
1.0000
2.2500
581.25
48.44
33000
13200
1603.89
0.35
0.12
52500
7000
lbs-in
2
in
in2
lbs/ft
lbs/in
psi Full Section Flexural Strength
psi
psi
psi
psi
=
=
=
=
=
Maximum Acting Shear Load =
Point Load M MAX
Unifrom Load M MAX
Applied M MAX
Total M MAX
Total Load
0.00
21796.88
0.00
21796.88
2906.25
1453.13
lbs-in
lbs-in
lbs-in
lbs-in
lbs
lbs
Deflection =
0.0695
in
L / 863.20
Note: The calculation for delfection is only for a Point Load and a
Uniform Load. The deflection for the Applied Moment is not
included.
3.00
2333.33
2100.00
4725.00
lbs
22340.61
psi
psi
O.K.
LOCAL BUCKLING
Critical Local
Buckling Stress scr =
b
z
p
q
=
=
=
=
If the calculated Local Buckling Stress above exceeds the Flange Compression Strength of the material, use cr
Therefore, cr
local
22340.61
20106.55
psi
Fb Local Buckling =
8042.62
psi
fb =
1603.89
psi
D =
JG =
Iww =
175028027.34
158203.13
469214648.44
local
O.K.
GLOBAL BUCKLING
global
75839.01
lbs
global
83707.52
psi
33000
psi
Therefore, cr
global
global
29700.00
psi
global
11880.00
psi
fb =
1603.89
psi
Fb
D Calcs.
155925000
18900000
203027.34
psi in
psi in4
psi in6
Pcrglobal Calcs.
0.0047694
5262127
3.0217848
O.K.
JG Calcs.
105468.75
52734.375
Iww Calcs.
467775000.00
1218164.063
221484.375
=
=
=
=
Vinyl Ester
100
0.00
lbs
300.00
psf
10.00%
0.00%
Beam Properties
10
bw = Web Depth =
in.
10.00
psf
bf = Flange Width =
in.
psf
tf = Flange Thickness =
0.375
in.
Safety Factor =
310.00
2.5
tw = Web Thickness =
0.375
in
Length of Beam ( L ) =
2.50
ft
30.00
in
Tributary width =
2.00
ft
24.00
in
720.00
in2
Area =
Weight =
6.57
in
4.92
lb/ft
Sx =
13.59
in
Ix =
40.76
r =
2.49
Sy =
Iy =
r
Full Section EX
EC-LW (Web)
EC-LW (Flange)
EC-CW (Web)
EC-CW (Flange)
Gxy
L
J
CW
=
=
=
=
=
=
=
=
=
=
ft
Unbraced Length ( Lu ) =
5.00
30.00
in4
Max Deflection =
0.13
in
in
0.00
in
Warning Box
4.44
in
13.32
1.42
4.000E+06
2.800E+06
3.850E+06
1.900E+06
1.900E+06
5.E+05
30.00
0.316
119.88
Area Of Load =
S.F.
Applied Moment =
in
in
psi
psi
psi
psi
psi
psi
in
AW
k
A'
w
w
Fb
Fb1
fb
vxy
vyx
=
=
=
=
=
=
=
=
=
=
=
in4
6
in
Compressive Strength, Fc-flg-LW
Ultimate Beam Shear Strength, Fv-ult =
0.00
2.2500
1.0000
2.2500
620.00
51.67
33000
13200
427.70
0.35
0.12
52500
7000
lbs-in
2
in
in2
lbs/ft
lbs/in
psi Full Section Flexural Strength
psi
psi
psi
psi
=
=
=
=
=
Maximum Acting Shear Load =
Point Load M MAX
Unifrom Load M MAX
Applied M MAX
Total M MAX
Total Load
0.00
5812.50
0.00
5812.50
1550.00
775.00
lbs-in
lbs-in
lbs-in
lbs-in
lbs
lbs
Deflection =
0.0085
in
L / 3525.71
Note: The calculation for delfection is only for a Point Load and a
Uniform Load. The deflection for the Applied Moment is not
included.
3.00
2333.33
2100.00
4725.00
lbs
22340.61
psi
psi
O.K.
LOCAL BUCKLING
Critical Local
Buckling Stress scr =
b
z
p
q
=
=
=
=
If the calculated Local Buckling Stress above exceeds the Flange Compression Strength of the material, use cr
Therefore, cr
local
22340.61
20106.55
psi
Fb Local Buckling =
8042.62
psi
fb =
427.70
psi
D =
JG =
Iww =
175028027.34
158203.13
469214648.44
local
O.K.
GLOBAL BUCKLING
global
581261.79
lbs
global
320784.65
psi
33000
psi
Therefore, cr
global
global
29700.00
psi
global
11880.00
psi
427.70
psi
Fb
fb =
D Calcs.
155925000
18900000
203027.34
psi in
psi in4
psi in6
Pcrglobal Calcs.
0.0190778
5262127
5.7900547
O.K.
JG Calcs.
105468.75
52734.375
Iww Calcs.
467775000.00
1218164.063
221484.375
=
=
=
=
Vinyl Ester
100
0.00
lbs
300.00
psf
10.00%
0.00%
Beam Properties
10
bw = Web Depth =
in.
10.00
psf
bf = Flange Width =
in.
psf
tf = Flange Thickness =
0.375
in.
Safety Factor =
310.00
2.5
tw = Web Thickness =
0.375
in
Length of Beam ( L ) =
6.00
ft
72.00
in
Tributary width =
2.00
ft
24.00
in
1728.00
in2
Area =
Weight =
6.57
in
4.92
lb/ft
Sx =
13.59
in
Ix =
40.76
r =
2.49
Sy =
Iy =
r =
Full Section EX =
EC-LW (Web) =
EC-LW (Flange) =
EC-CW (Web) =
EC-CW (Flange) =
Gxy =
L =
J =
CW =
ft
Unbraced Length ( Lu ) =
12.00
72.00
in4
Max Deflection =
0.13
in
in
0.00
in
Warning Box
4.44
in
13.32
1.42
4.000E+06
2.800E+06
3.850E+06
1.900E+06
1.900E+06
5.E+05
72.00
0.316
119.88
Area Of Load =
S.F.
Applied Moment =
in
in
psi
psi
psi
psi
psi
psi
in
AW
k
A'
w
w
Fb
Fb1
fb
vxy
vyx
=
=
=
=
=
=
=
=
=
=
=
in4
6
in
Compressive Strength, Fc-flg-LW
Ultimate Beam Shear Strength, Fv-ult =
0.00
2.2500
1.0000
2.2500
620.00
51.67
33000
13200
2463.58
0.35
0.12
52500
7000
lbs-in
2
in
in2
lbs/ft
DEFLECTION IS OVER THE MAX
lbs/in
psi Full Section Flexural Strength
psi
psi
psi
psi
=
=
=
=
=
Maximum Acting Shear Load =
Point Load M MAX
Unifrom Load M MAX
Applied M MAX
Total M MAX
Total Load
0.00
33480.00
0.00
33480.00
3720.00
1860.00
lbs-in
lbs-in
lbs-in
lbs-in
lbs
lbs
Deflection =
0.1406
in
L / 511.92
Note: The calculation for delfection is only for a Point Load and a
Uniform Load. The deflection for the Applied Moment is not
included.
3.00
2333.33
2100.00
4725.00
lbs
22340.61
psi
psi
O.K.
LOCAL BUCKLING
Critical Local
Buckling Stress scr =
b
z
p
q
=
=
=
=
If the calculated Local Buckling Stress above exceeds the Flange Compression Strength of the material, use cr
Therefore, cr
local
22340.61
20106.55
psi
Fb Local Buckling =
8042.62
psi
fb =
2463.58
psi
D =
JG =
Iww =
175028027.34
158203.13
469214648.44
local
O.K.
GLOBAL BUCKLING
global
44933.29
lbs
global
59514.29
psi
33000
psi
Therefore, cr
global
global
29700.00
psi
global
11880.00
psi
fb =
2463.58
psi
Fb
D Calcs.
155925000
18900000
203027.34
psi in
psi in4
psi in6
Pcrglobal Calcs.
0.0033121
5262127
2.5781107
O.K.
JG Calcs.
105468.75
52734.375
Iww Calcs.
467775000.00
1218164.063
221484.375
Engineer's
Comment: Because
the /L ratio is so
high (1/512), SAY
OK.
=
=
=
=
Vinyl Ester
100
0.00
lbs
300.00
psf
10.00%
0.00%
Beam Properties
10
bw = Web Depth =
in.
10.00
psf
bf = Flange Width =
in.
psf
tf = Flange Thickness =
0.375
in.
Safety Factor =
310.00
2.5
tw = Web Thickness =
0.375
in
Length of Beam ( L ) =
2.50
ft
30.00
in
Tributary width =
2.50
ft
30.00
in
900.00
in2
Area =
Weight =
6.57
in
4.92
lb/ft
Sx =
13.59
in
Ix =
40.76
r =
2.49
Sy =
Iy =
r
Full Section EX
EC-LW (Web)
EC-LW (Flange)
EC-CW (Web)
EC-CW (Flange)
Gxy
L
J
CW
=
=
=
=
=
=
=
=
=
=
ft
Unbraced Length ( Lu ) =
6.25
30.00
in4
Max Deflection =
0.13
in
in
0.00
in
Warning Box
4.44
in
13.32
1.42
4.000E+06
2.800E+06
3.850E+06
1.900E+06
1.900E+06
5.E+05
30.00
0.316
119.88
Area Of Load =
S.F.
Applied Moment =
in
in
psi
psi
psi
psi
psi
psi
in
AW
k
A'
w
w
Fb
Fb1
fb
vxy
vyx
=
=
=
=
=
=
=
=
=
=
=
in4
6
in
Compressive Strength, Fc-flg-LW
Ultimate Beam Shear Strength, Fv-ult =
0.00
2.2500
1.0000
2.2500
775.00
64.58
33000
13200
534.63
0.35
0.12
52500
7000
lbs-in
2
in
in2
lbs/ft
lbs/in
psi Full Section Flexural Strength
psi
psi
psi
psi
=
=
=
=
=
Maximum Acting Shear Load =
Point Load M MAX
Unifrom Load M MAX
Applied M MAX
Total M MAX
Total Load
0.00
7265.63
0.00
7265.63
1937.50
968.75
lbs-in
lbs-in
lbs-in
lbs-in
lbs
lbs
Deflection =
0.0106
in
L / 2820.57
Note: The calculation for delfection is only for a Point Load and a
Uniform Load. The deflection for the Applied Moment is not
included.
3.00
2333.33
2100.00
4725.00
lbs
22340.61
psi
psi
O.K.
LOCAL BUCKLING
Critical Local
Buckling Stress scr =
b
z
p
q
=
=
=
=
If the calculated Local Buckling Stress above exceeds the Flange Compression Strength of the material, use cr
Therefore, cr
local
22340.61
20106.55
psi
Fb Local Buckling =
8042.62
psi
fb =
534.63
psi
D =
JG =
Iww =
175028027.34
158203.13
469214648.44
local
O.K.
GLOBAL BUCKLING
global
581261.79
lbs
global
320784.65
psi
33000
psi
Therefore, cr
global
global
29700.00
psi
global
11880.00
psi
534.63
psi
Fb
fb =
D Calcs.
155925000
18900000
203027.34
psi in
psi in4
psi in6
Pcrglobal Calcs.
0.0190778
5262127
5.7900547
O.K.
JG Calcs.
105468.75
52734.375
Iww Calcs.
467775000.00
1218164.063
221484.375
=
=
=
=
Vinyl Ester
100
0.00
lbs
300.00
psf
10.00%
0.00%
Beam Properties
10
bw = Web Depth =
in.
10.00
psf
bf = Flange Width =
in.
psf
tf = Flange Thickness =
0.375
in.
Safety Factor =
310.00
2.5
tw = Web Thickness =
0.375
in
Length of Beam ( L ) =
5.67
ft
68.04
in
Tributary width =
2.13
ft
25.56
in
1739.10
in2
Area =
Weight =
6.57
in
4.92
lb/ft
Sx =
13.59
in
Ix =
40.76
r =
2.49
Sy =
Iy =
r
Full Section EX
EC-LW (Web)
EC-LW (Flange)
EC-CW (Web)
EC-CW (Flange)
Gxy
L
J
CW
=
=
=
=
=
=
=
=
=
=
ft
Unbraced Length ( Lu ) =
12.08
50.00
in4
Max Deflection =
0.13
in
in
0.00
in
Warning Box
4.44
in
13.32
1.42
4.000E+06
2.800E+06
3.850E+06
1.900E+06
1.900E+06
5.E+05
68.04
0.316
119.88
Area Of Load =
S.F.
Applied Moment =
in
in
psi
psi
psi
psi
psi
psi
in
AW
k
A'
w
w
Fb
Fb1
fb
vxy
vyx
=
=
=
=
=
=
=
=
=
=
=
in4
6
in
Compressive Strength, Fc-flg-LW
Ultimate Beam Shear Strength, Fv-ult =
0.00
2.2500
1.0000
2.2500
660.30
55.03
33000
13200
2343.04
0.35
0.12
52500
7000
lbs-in
2
in
in2
lbs/ft
lbs/in
psi Full Section Flexural Strength
psi
psi
psi
psi
=
=
=
=
=
Maximum Acting Shear Load =
Point Load M MAX
Unifrom Load M MAX
Applied M MAX
Total M MAX
Total Load
0.00
31841.88
0.00
31841.88
3743.90
1871.95
lbs-in
lbs-in
lbs-in
lbs-in
lbs
lbs
Deflection =
0.1225
in
L / 555.50
Note: The calculation for delfection is only for a Point Load and a
Uniform Load. The deflection for the Applied Moment is not
included.
3.00
2333.33
2100.00
4725.00
lbs
22340.61
psi
psi
O.K.
LOCAL BUCKLING
Critical Local
Buckling Stress scr =
b
z
p
q
=
=
=
=
If the calculated Local Buckling Stress above exceeds the Flange Compression Strength of the material, use cr
Therefore, cr
local
22340.61
20106.55
psi
Fb Local Buckling =
8042.62
psi
fb =
2343.04
psi
D =
JG =
Iww =
175028027.34
158203.13
469214648.44
local
O.K.
GLOBAL BUCKLING
global
128838.50
lbs
global
161261.43
psi
33000
psi
Therefore, cr
global
global
29700.00
psi
global
11880.00
psi
fb =
2343.04
psi
Fb
D Calcs.
155925000
18900000
203027.34
psi in
psi in4
psi in6
Pcrglobal Calcs.
0.006868
5262127
3.564955
O.K.
JG Calcs.
105468.75
52734.375
Iww Calcs.
467775000.00
1218164.063
221484.375
=
=
=
=
Vinyl Ester
100
0.00
lbs
300.00
psf
10.00%
0.00%
Beam Properties
10
bw = Web Depth =
in.
10.00
psf
bf = Flange Width =
in.
psf
tf = Flange Thickness =
0.375
in.
Safety Factor =
310.00
2.5
tw = Web Thickness =
0.375
in
Length of Beam ( L ) =
2.50
ft
30.00
in
Tributary width =
2.50
ft
30.00
in
900.00
in2
Area =
Weight =
6.57
in
4.92
lb/ft
Sx =
13.59
in
Ix =
40.76
r =
2.49
Sy =
Iy =
r
Full Section EX
EC-LW (Web)
EC-LW (Flange)
EC-CW (Web)
EC-CW (Flange)
Gxy
L
J
CW
=
=
=
=
=
=
=
=
=
=
ft
Unbraced Length ( Lu ) =
6.25
30.00
in4
Max Deflection =
0.13
in
in
0.00
in
Warning Box
4.44
in
13.32
1.42
4.000E+06
2.800E+06
3.850E+06
1.900E+06
1.900E+06
5.E+05
30.00
0.316
119.88
Area Of Load =
S.F.
Applied Moment =
in
in
psi
psi
psi
psi
psi
psi
in
AW
k
A'
w
w
Fb
Fb1
fb
vxy
vyx
=
=
=
=
=
=
=
=
=
=
=
in4
6
in
Compressive Strength, Fc-flg-LW
Ultimate Beam Shear Strength, Fv-ult =
0.00
2.2500
1.0000
2.2500
775.00
64.58
33000
13200
534.63
0.35
0.12
52500
7000
lbs-in
2
in
in2
lbs/ft
lbs/in
psi Full Section Flexural Strength
psi
psi
psi
psi
=
=
=
=
=
Maximum Acting Shear Load =
Point Load M MAX
Unifrom Load M MAX
Applied M MAX
Total M MAX
Total Load
0.00
7265.63
0.00
7265.63
1937.50
968.75
lbs-in
lbs-in
lbs-in
lbs-in
lbs
lbs
Deflection =
0.0106
in
L / 2820.57
Note: The calculation for delfection is only for a Point Load and a
Uniform Load. The deflection for the Applied Moment is not
included.
3.00
2333.33
2100.00
4725.00
lbs
22340.61
psi
psi
O.K.
LOCAL BUCKLING
Critical Local
Buckling Stress scr =
b
z
p
q
=
=
=
=
If the calculated Local Buckling Stress above exceeds the Flange Compression Strength of the material, use cr
Therefore, cr
local
22340.61
20106.55
psi
Fb Local Buckling =
8042.62
psi
fb =
534.63
psi
D =
JG =
Iww =
175028027.34
158203.13
469214648.44
local
O.K.
GLOBAL BUCKLING
global
581261.79
lbs
global
320784.65
psi
33000
psi
Therefore, cr
global
global
29700.00
psi
global
11880.00
psi
534.63
psi
Fb
fb =
D Calcs.
155925000
18900000
203027.34
psi in
psi in4
psi in6
Pcrglobal Calcs.
0.0190778
5262127
5.7900547
O.K.
JG Calcs.
105468.75
52734.375
Iww Calcs.
467775000.00
1218164.063
221484.375
END OF SECTION
www.hilti.us
Company:
Specifier:
Address:
Phone I Fax:
E-Mail:
Page:
Project:
Sub-Project I Pos. No.:
Date:
1
Delta Job No. 17134
Heumann Enviro.
5/28/2015
Specifier's comments: HAS R316 + HY 200 Safe Set Sys Epoxy Anchors for W6 x 3/8 Beams Head On to Concrete Wall Rev B
1 Input data
Anchor type and diameter:
Material:
ASTM F 593
ESR-3187
Issued I Valid:
4/1/2013 | 3/1/2014
Proof:
Stand-off installation:
Anchor plate:
lx x ly x t = 4.500 in. x 8.375 in. x 0.500 in.; (Recommended plate thickness: not calculated)
Profile:
no profile
Base material:
cracked concrete, 3000, fc' = 3000 psi; h = 12.000 in., Temp. short/long: 100/95 F
Installation:
Reinforcement:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.us
Company:
Specifier:
Address:
Phone I Fax:
E-Mail:
2
Delta Job No. 17134
Heumann Enviro.
5/28/2015
Page:
Project:
Sub-Project I Pos. No.:
Date:
Shear force y
0
0
3 Tension load
Steel Strength*
Utilization bN = Nua/fNn
N/A
Status
N/A
Bond Strength**
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.us
3
Delta Job No. 17134
Heumann Enviro.
5/28/2015
Page:
Project:
Sub-Project I Pos. No.:
Date:
Company:
Specifier:
Address:
Phone I Fax:
E-Mail:
4 Shear load
Load Vua [lb]
1152
Steel Strength*
Utilization bV = Vua/fVn
23
Status
OK
N/A
N/A
N/A
N/A
2304
8018
29
OK
N/A
N/A
N/A
N/A
Variables
n
1
Ase,V [in.2]
0.14
futa [psi]
100000
fsteel
0.600
f Vsa [lb]
5109
Calculations
Vsa [lb]
8515
Results
Vsa [lb]
8515
Vua [lb]
1152
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.us
Delta Composites LLC
Rodney H Masters
23219 W. Hardy Rd, Spring TX 77373
281-907-0619 | 281-907-0323
rmasters@deltacomposites.com
Company:
Specifier:
Address:
Phone I Fax:
E-Mail:
Page:
Project:
Sub-Project I Pos. No.:
Date:
4
Delta Job No. 17134
Heumann Enviro.
5/28/2015
=kcp
[(AA ) y
Na
Na0
ed,Na
f Vcpg Vua
ANa see ICC-ES AC308, Part D.5.3.7
ANa0 = s2cr,Na
scr,Na = 20 d tk,uncr 3 hef
1450
s
ccr,Na = cr,Na
2
ca,min
1.0
yed,Na = 0.7 + 0.3 c
cr,Na
0.5
savg
(1 - yg,Na0) 1.0
yg,Na = yg,Na0 +
scr,Na
yg,Na0
( )
[( )
]
= n - [(n - 1) ( t
) ] 1.0
t
k,c
yp,Na
Na0
1.5
k,max,c
kc
h f'
p d ef c
1
2'
1.0
=
1 + e,N
scr,Na
c
c
= MAX a,min, cr,Na 1.0
cac cac
= tk,c kbond p d hef
tk,max,c =
yec,Na
Variables
kcp
2.000
tk,c,uncr [psi]
1515
tk,c [psi]
847
danchor [in.]
0.500
hef [in.]
2.750
savg [in.]
4.375
n
2
kc
17
f'c [psi]
3000
ec1,N [in.]
0.000
ec2,N [in.]
0.000
ca,min [in.]
4.500
cac [in.]
4.136
kbond
1.00
scr,Na [in.]
8.250
ccr,Na [in.]
4.125
ANa [in.2]
104.16
ANa0 [in.2]
68.06
yed,N
1.000
tk,max [psi]
983
yg,Na0
1.083
yg,Na
1.022
yec1,N
1.000
yec2,N
1.000
yp,Na
1.000
Na0 [lb]
3660
fconcrete
0.700
f Vcpg [lb]
8018
Vua [lb]
2304
Calculations
Results
Vcpg [lb]
11454
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.us
Company:
Specifier:
Address:
Phone I Fax:
E-Mail:
Page:
Project:
Sub-Project I Pos. No.:
Date:
5
Delta Job No. 17134
Heumann Enviro.
5/28/2015
5 Warnings
To avoid failure of the anchor plate the required thickness can be calculated in PROFIS Anchor. Load re-distributions on the anchors due to
elastic deformations of the anchor plate are not considered. The anchor plate is assumed to be sufficiently stiff, in order not to be deformed when
subjected to the loading!
Condition A applies when supplementary reinforcement is used. The factor is increased for non-steel Design Strengths except Pullout Strength
and Pryout strength. Condition B applies when supplementary reinforcement is not used and for Pullout Strength and Pryout Strength. Refer to
your local standard.
Design Strengths of adhesive anchor systems are influenced by the cleaning method. Refer to the INSTRUCTIONS FOR USE given in the
Evaluation Service Report for cleaning and installation instructions
The present version of the software does not account for adhesive anchor special design provisions corresponding to overhead applications.
Refer to the ICC-ES Evaluation Service Report (e.g. section 4.1.1 of the ICC-ESR 2322) for details.
Checking the transfer of loads into the base material and the shear resistance are required in accordance with ACI318 or the relevant standard!
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.us
6
Delta Job No. 17134
Heumann Enviro.
5/28/2015
Page:
Project:
Sub-Project I Pos. No.:
Date:
Company:
Specifier:
Address:
Phone I Fax:
E-Mail:
6 Installation data
Anchor plate, steel: Profile: no profile; 0.000 x 0.000 x 0.000 in.
Hole diameter in the fixture: df = 0.563 in.
Plate thickness (input): 0.500 in.
Recommended plate thickness: not calculated
Cleaning: Premium cleaning of the drilled hole is required
2.250
4.188
2.000
2.250
4.375
4.188
2.000
2.250
2.250
x
0.000
0.000
y
-2.188
2.188
c-x
4.500
4.500
c+x
-
c-y
-
c+y
-
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.us
Company:
Specifier:
Address:
Phone I Fax:
E-Mail:
Page:
Project:
Sub-Project I Pos. No.:
Date:
7
Delta Job No. 17134
Heumann Enviro.
5/28/2015
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
END OF SECTION
ANNEX 1
38
Concentration
Percentage
0-50
-100
100
-10
100
10
100
10
100
--100
-10
5 20
100
0 - 10
-25
15
-25
10
-5
10
20
15
5 - 20
-15
-100
100
100
10
100
10
-100
39
Chemical Environment
BENZENE IN KEROSENE
BENZENE SULFURIC ACID
BENZOIC ACID
O-BENZOYL BENZOIC ACID
BENZYL ALCOHOL
BENZYL CHLORIDE
BORAX
BRASS PLATING SOLUTION
BUTYL ACETATE
BUTYRIC ACID
BUTYLENE GLYCOL
CADMIUM CHLORIDE
CADMIUM CYANIDE PLATING
CALCIUM BISULFITE
CALCIUM CARBONATE
CALCIUM CHLORIDE
CALCIUM CHLORATE
CALCIUM HYDROXIDE
CALCIUM HYPOCHLORITE
CALCIUM NITRATE
CALCIUM SULFATE
CALCIUM SULFITE
CAPRYLIC ACID
CARBON DIOXIDE
CARBON DISULFIDE
CARBON MONOXIDE GAS
CARBON TETRACHLORIDE
CARBONIC ACID
CARBON METHYL CELLULOSE
CASTOR OIL
CHLORINATED WAX
CHLORINE DIOXIDE/AIR
CHLORINE DIOXIDE, WET GAS
CHLORINE DRY GAS
CHLORINE WET GAS
CHLORINE LIQUID
CHLORINE WATER
CHLOROACETIC ACID
CHLOROBENZENE
CHLOROFORM
CHLOROSULFONIC ACID
CHROMIC ACID
Concentration
Percentage
5
5 - 20
5 - 20
-100
100
5 - 20
--5 - 30
100
---10
10
10
5 - 20
10
5
10
---100
-100
10
-100
10
-----10
0 - 50
-100
-5
40
Chemical Environment
CHROMIC ACID
CHROMIC ACID
CHROMIUM SULFATE
CITRIC ACID
COCONUT OIL
COPPER CHLORIDE
COPPER CYANIDE
COPPER FLUORIDE
COPPER NITRATE
COPPER BRITE PLATING
COPPER PLATING SOLUTION
COPPER MATTE DIPPING BATH
COPPER PICKLING BATH
COPPER SULFATE
CORN OIL
CORN STARCH- SLURRY
CORN SUGAR
COTTONSEED OIL
CRUDE OIL
CYCLOHEXENE
CYCLOHEXENE VAPOR
DEIONIZED WATER
DETERGENTS SULFONATED
DI-AMMONIUM PHOSPHATE
DIBROMOPHENOL
DIBUTYL ETHER
DICHLORO BENZENE
DICHLOROETHYLENE
DIETHYLENE GLYCOL
DIETHYL ETHER
DIMENTHYL PHTHALATE
DIOCTYL PHTHALATE
DIPROPYLENE GLYCOL
DODECYL ALCOHOL
ESTER, FATTY ACIDS
ETHYL ACETATE
ETHYL BENZENE
ETHYL ETHER
ETHYLENE GLYCOL
ETHYLENE DICHLORIDE
FATY ACIDS
FERRIC CHLORIDE
Concentration
Percentage
20
30
-5 - 30
-5
5
-------100
-100
-100
----------100
--100
--100
--100
-10
10
41
Chemical Environment
FERRIC NITRATE
FERRIC SULFATE
FERROUS CHLORIDE
FERROUS NITRATE
FERROUS SULFATE
8-8-8 FERTILIZER
FLUOBORIC ACID
FLUSOILICIC ACID
FORMALDEHYDE
FORMIC ACID
FUEL GAS
FUEL OIL
GAS NATURAL
GASOLINE AUTO
GASOLINE AVIATION
GASOLINE ETHYL
GASOLINE SOUR
GLUCONIC ACID
GLUCOSE
GLYCERIN
GLYCOL ETHYLENE
GLYCOL PROPYLENE
GLYCOLIC ACID
GOLD PLATING SOLUTION
HEPTANE
HEXANE
HEXALENE GLYCOL
HYDRAULIC FLUID
HYDROBROMIC ACID
HYDROCHLORIC ACID
HYDROCYANIC ACID
HYDROFLUORIC ACID
HYDROFLOUSILIC ACID
HYDROZINE
HYDROGEN BROMIDE, DRY
HYDROGEN BROMIDE, WET GAS
HYDROGEN CHLORIDE, DRY GAS
HYDROGEN CHLORIDE, WET GAS
HYDROGEN PEROXIDE
HYDROGEN SULFIDE DRY
HYDROGEN SULFIDE AQUEOUS
HYDROGEN FLUORIDE VAPORS
Concentration
Percentage
10
10
------5 - 30
25
-100
------100
100
----100
100
-100
5 - 50
10 - 30
--10
100
---------
42
Chemical Environment
HYDROSULFITE BLEACH
HYPOCHLORUS ACID
IRON PLATING SOLUTION
IRON & STEEL CLEANING BATH
ISOPROPYL AMINE
ISOPROPYL PAMITATE
JET FUEL
KEROSENE
LACTIC ACID
LAUROYL CHLORIDE
LAURIC ACID
LEAD ACETATE
LEAD CHLORIDE
LEAD NITRATE
LEAD PLATING SOLUTION
LEVULINIC ACID
LINSEED OIL
LITHIUM BROMIDE
LITHIUM CHLORIDE
LITHIUM SULFATE
LITHIUM HYDROXIDE
MAGNESIUM BISUFITE
MAGNESIUM CARBONATE
MAGNESIUM CHLORIDE
MAGNESIUM HYDROXIDE
MAGNESIUM NITRATE
MAGNESIUM SULFATE
MALEIC ACID
MERCURIC CHLORIDE
MERCUROUS CHLORIDE
METHANOL
METHYLENE CHLORIDE
METHYL ETHYL KETONE @120F
METHYL ISOBUTYL CARBITOL
METHYL ISOBUTYL KETONE
METHYL STYRENE
MINERAL OIL
MOLYBDENUM DISULFIDE
MONOCHLORIC ACETIC ACID
MONOETHANOLAMINE
MOTOR OIL
MYRISTIC ACID
Concentration
Percentage
-----------100
10
10
----25
-10
-10
10
10
10
10
100
10
10
------100
---100
--
43
Chemical Environment
NAPTHA
NICKEL CHLORIDE
NICKEL NITRATE
NICKEL PLATING: .4% Boric Acid
NICKEL PLATING: 11%Nickel Sulfate,
2% Nickle Chloride, 1% Boric Acid
NICKEL PLATING: 44% Nickel Sulfate,
2% Ammonium Chloride, 4% Boric Acid
NICKEL SULFATE
NITRIC ACID
NITRIC ACID FUMES
NITROBENZENE
OCTONOIC ACID
OIL, SOUR CRUDE
OIL SWEET CRUDE
OLEIC ACID
OLEUM (FUMING SULFURIC)
OILVE OIL
OXALIC ACID
PEROXIDE BLEACH: 2% Sodium Peroxide96% .025 Epsom Salts, 5% Sodium Silicate
42 Be, 1.4% Sulfuric Acid 66Be
PHENOL
PHENOL SULFONIC ACID
PHOSPHORIC ACID
PHOSPHORIC ACID FUMES
PHOSPHORUS
PENTOXIDE
PHOSPHOROUS TRICHLORIDE
PHTHALIC ACID
PICKLING ACIDS: Sulfuric and
Hydrochloric
PICRIC ACID ALCOHOLIC
POLYVINYL ACETATE LATEX
POLYVINYL ALCOHOL
POLYVINYL CHLORIDE LATEX: With
35(Parts Drop)
POTASSIUM ALUMINUM SULFATE
POTASSIUM BICARBONATE
POTASSIUM BROMIDE
POTASSIUM CARBONATE
POTASSIUM CHLORIDE
POTASSIUM DICHROMATE
Concentration
Percentage
100
10
10
--
--
NR
160/71
-10
5 - 30
---100
100
100
----
NR
120/49
NR
NR
NR
NR
NR
NR
120/49
NR
150/65
150/65
160/71
150/65
100/38
NR
NR
160/71
120/49
120/49
150/65
NR
160/71
160/71
-10
-5 - 50
--
150/65
NR
NR
100/38
150/65
160/71
NR
NR
150/65
160/71
-100
100
150/65
NR
NR
160/71
NR
120/49
---100
150/65
150/65
NR
NR
160/71
160/71
160/71
100/38
-10
-10
10
100
100
NR
120/49
NR
NR
NR
NR
NR
120/49
150/65
120/49
120/49
120/49
120/49
120/49
44
Chemical Environment
POTASSIUM FERRICYANIDE
POTASSIUM HYDROXIDE
POTASSIUM NITRATE
POTASSIUM PERMANGANTE
POTASSIUM PERSULFATE
POTASSIUM SULFATE
PROPIONIC ACID
PROPIONIC ACID
PROPYLENE GLYCOL
PULP PAPER MILL EFFLUENT
PYRIDINE
SALICYLIC ACID
SEA WATER
SEWAGE TREATMENT
SEBACIC ACID
SELENIOUS ACID
SILVER NITRATE
SILVER PLATING SOLUTION: 4% Silver
Cyanide, 7% Potassium, 5% Sodium Cyanide,
2% Potassium Carbonate
SOAPS
SODIUM ACETATE
SODIUM BENZOATE
SODIUM BICARBONATE
SODIUM BIFLUORIDE
SODIUM BISULFATE
SODIUM BISULFITE
SODIUM BROMATE
SODIUM BROMIDE
SODIUM CARBONATE
SODIUM CHLORATE
SODIUM CHLORIDE
SODIUM CHLORITE
SODIUM CHROMATE
SODIUM CYANIDE
SODIUM DICHROMATE
SODIUM DI-PHOSPHATE
SODIUM FERRICYANIDE
SODIUM FLUORIDE
SODIUM FLOURO SILICATE
SODIUM HEXAMETAPHOSPHATES
Concentration
Percentage
-10
10
100
-10
1 - 50
50 - 100
100
---------
----------0 - 25
--25
---------
45
NR
NR
NR
NR
150/65
NR
150/65
150/65
150/65
150/65
NR
NR
150/65
NR
150/65
NR
150/65
150/65
150/65
NR
NR
NR
160/71
160/71
160/71
160/71
160/71
160/71
160/71
160/71
140/60
160/71
160/71
160/71
160/71
160/71
160/71
160/71
160/71
160/71
160/71
120/49
120/49
100/38
Chemical Environment
SODIUM HYDROXIDE
SODIUM HYDROXIDE
SODIUM HYDROXIDE
SODIUM HYDROSULFATE
SODIUM HYPOCHLORITE
SODIUM LAURYL SULFATE
SODIUM MONO-PHOSPHATE
SODIUM NITRATE
SODIUM SILICATE
SODIUM SULFATE
SODIUM SULFIDE
SODIUM SULFITE
SODIUM TETRA BORATE
SODIUM THIOCAYNATE
SODIUM THIOSULFATE
SODIUM POLYOPHOSPHATE
SODIUM XYLENE SULFONATE
SODIUM SOLUTIONS
SODIUM CRUDE OIL
SOVA OIL
STANNIC CHLORIDE
STANNOUS CHLORIDE
STEARIC ACID
STYRENE
SUGAR, BEET AND CANE LIQUOR
SUGAR, SUCROSE
SULFAMIC ACID
SULFANILIC ACID
SULFATED DETERGENTS
SULFUR DIOXIDE, WET OR DRY
SULFER, TRIOXIDE/AIR
SULFURIC ACID
SULFURIC ACID
SULFURIC ACID
SULFUROUS ACID
SUPERPHOSPHORIC ACID: 76% P205
TALL OIL
TANNIC ACID
TARTARIC ACID
THIONYL CHLORIDE
TIN PLATING SOLUTION: 18% Stannous
Fluroborate, 7% Tin, 9% Flouroboric acid, 2%
Boric Acid
Concentration
Percentage
05
5 - 25
50
-10
--------------------------0 - 30
30 - 50
50 - 70
10
------
--
46
NR
160/71
Chemical Environment
TOLUENE
TOLUENE SOLFONIC ACID
TRANSFORMER OILS: Mineral Oil Types,
Chloro-phenyl Types
TRICHLOR ACETIC ACID
TRICHLORETHYLENE
TRICHLOROPENOL
TRICRESYL PHOSPHATE +A618
TRIDECYLBENZENE SULFONATE
TRISODIUM PHOSPHATE
TURPENTINE
UREA
VEGETABLE OILS
VINEGAR
VINYL ACETATE
WATER:
DEIONIZED
DEMINERALIZED
DISTILLED
FRESH
SALT
SEA
WHITE LIQUOR (Pulp Mill)
XYLENE
ZINC CHLORATE
ZINC NITRATE
ZINC PLATING SOLUTION: 9% Zinc
Cyanide, 4% Sodium Cyanide, 9% Sodium
Hydroxide
ZINC PLATING SOLUTION: 49% Zinc
Fluoroborate, 5% Ammonium Chloride, 6%
Ammonium Fluoroborate
ZINC SULFATE
Concentration
Percentage
---
-50
-----------
NR
NR
NR
NR
NR
NR
NR
NR
NR
150/65
150/65
NR
NR
160/71
NR
NR
120/49
160/71
160/71
100/38
140/60
160/71
160/71
NR
-----------
150/65
150/65
150/65
150/65
150/65
150/65
NR
NR
150/65
150/65
160/71
160/71
160/71
160/71
160/71
160/71
160/71
NR
160/71
160/71
--
NR
120/49
---
NR
150/65
160/71
160/71
47
ANNEX 2
ANNEX 3
This Certificate is subject to terms and conditions overleaf. Any significant change in design or construction may render this Certificate invalid.
The validity date relates to the Type Approval Certificate and not to the approval of equipment/systems installed.
If any person suffers loss or damage which is proved to have been caused by any negligent act or omission of Det Norske Veritas, then Det Norske Veritas shall pay compensation to such
person for his proved direct loss or damage. However, the compensation shall not exceed an amount equal to ten times the fee charged for the service in question, provided that the maximum
compensation shall never exceed USD 2 million. In this provision "Det Norske Veritas" shall mean the Foundation Det Norske Veritas as well as all its subsidiaries, directors, officers,
employees, agents and any other acting on behalf of Det Norske Veritas.
DET NORSKE VERITAS AS, Veritasveien 1, NO-1322 Hvik, Norway, Tel.: +47 67 57 99 00, Org.No. NO 945 748 931 MVA.
Form No.: TA 1411a Issue: December 2012
www.dnv.com
Page 1 of 3
Product description
Jossongrate (Powergrate) Pultruded Fiberglass Grating with the following properties and test results:
Product name (ref. test report)
IFR-25 (ISOPHTHALIC RESIN), I6015, 1 THICK,
60% OPENING
VEFR-10 (VINYL ESTER RESIN), I6015, 1 THICK, 60%
OPENING
Flame Spread
Index
20
Smoke
Developed Index
400
Weight
2
[Kg/m ]
16.1
350
16.1
Jossongrate (Powergrate) Molded Fiberglass Grating with the following properties and test results:
Product name (ref. test report)
OFR-25 (ORTHOPHITHALIC RESIN), 1 THICK x
1 x 1 SQUARE MESH
IFR-10 (ISOPHTHALIC RESIN), 1 THICK x
1 x 1 SQUARE MESH
IFR-25 (ISOPHTHALIC RESIN), 1 1/2 THICK x
1 x 1 SQUARE MESH
VEFR-10 (VINYL ESTER RESIN) 1 THICK x
1 x 1 SQUARE MESH
Flame Spread
Index
15
Smoke
Developed Index
250
Weight
2
[Kg/m ]
12.3
135
12.3
15
200
19.5
195
12.3
Application/Limitation
For use in locations according to enclosed Structural Fire Integrity Matrix.
Structural Fire Integrity Matrix.
Location
Machinery Spaces
Cargo Tanks
Fuel Oil Tanks
Ballast Water Tanks
Cofferdams, void spaces, double bottoms, pipe
tunnels, etc.
Accommodation, service, and control spaces
Lifeboat embarkation or temporary safe refuge
stations in open deck areas
Service
Walkways or areas which may be used for
escape, or access for fire fighting, emergency
operation or rescue
Personnel walkways, catwalks, ladders,
platforms or access areas other than those
described above
All personnel walkways, catwalks, ladders,
platforms or access areas
Walkways or areas which may be used for
escape, or access for fire fighting, emergency
operation or rescue
Personnel walkways, catwalks, ladders,
platforms or access areas other than those
described above
All personnel walkways, catwalks, ladders,
platforms or access areas
All personnel walkways, catwalks, ladders,
platforms or access areas
All personnel walkways, catwalks, ladders,
platforms or access areas
All personnel walkways, catwalks, ladders,
platforms or access areas
All personnel walkways, catwalks, ladders,
platforms or access areas
All personnel walkways, catwalks, ladders,
platforms or access areas
DET NORSKE VERITAS AS, Veritasveien 1, NO-1322 Hvik, Norway, Tel.: +47 67 57 99 00, Org.No. NO 945 748 931 MVA.
Form No.: TA 1411a Issue: December 2012
IFR-25, VEFR-10,
OFR-25, IFR-10,
IFR-25 and VEFR-10
NO
NO
NO
NO
YES
NO
YES1
YES1
YES1
NO
NO
www.dnv.com
Page 2 of 3
(1)
NO
YES
NO
The grating can only be used if these spaces are normally not entered when underway.
Marking of product
The product is to be marked with name of manufacturer and type designation.
DET NORSKE VERITAS AS, Veritasveien 1, NO-1322 Hvik, Norway, Tel.: +47 67 57 99 00, Org.No. NO 945 748 931 MVA.
Form No.: TA 1411a Issue: December 2012
www.dnv.com
Page 3 of 3
ANNEX 4
Description:
Ratings:
Service Restrictions:
1. Unit Certification is not required for this product. If the manufacturer or purchaser
request an ABS Certificate for compliance with a specification or standard, the
specification or standard, including inspection standards and tolerances, must be
clearly defined. 2. Not to be used as walkways or areas, which may be used for
escape or access for firefighting, emergency operation or rescue in machinery
01/08/2014 9:01:15 PM
Page 1 of 2
spaces and cargo holds. 3. The product is not to be used in areas where L1, L2 or
L3 rated FRP grating required in ABS Rules for Building and Classing Facilities on
Offshore Installations.
Comments:
Notes / Documentation:
1. Test report No. 01.10932.01.190e dated August 23, 2005 (For model P-VEFR-5)
2. Test report No. 01.10932.01.190f dated August 23, 2005 (For model P-IFR-20)
3. Test report No. 01.10932.01.190d dated July 11, 2005 (For model M-P-5) 4.
Test report No. 01.10932.01.190c dated July 11, 2005 (For model M-VEFR-10) 5.
Test report No. 01.10932.01.190a dated July 11, 2005 (For model M-OFR-15) 6.
Test report No. 01.10932.01.190b dated July 11, 2005 (For model M-IFR-20)
(Issued by Southwest Research Institute. USA)
Term of Validity:
ABS Rules:
The Rules applicable to this assessment are: 2013 ABS Steel Vessel Rules
1-1-Appendix 3.
National Standards:
International Standards:
Government Authority:
EUMED:
Others:
Model Certificate
PDA
Model Certificate No
07-SQ289844-1-PDA
Issue Date
11/NOV/2013
Expiry Date
10/NOV/2018
ABS Programs
ABS has used due diligence in the preparation of this certificate and it represents the information on the product in the ABS Records as of the
date and time the certificate was printed. Type Approval requires Drawing Assessment, Prototype Testing and assessment of the
manufacturer's quality assurance and quality control arrangements. Limited circumstances may allow only Prototype Testing to satisfy Type
Approval. The approvals of Drawings and Products remain valid as long as the ABS Rule, to which they were assessed, remains valid. ABS
cautions manufacturers to review and maintain compliance with all other specifications to which the product may have been assessed. Further,
unless it is specifically indicated in the description of the product; Type Approval does not necessarily waive witnessed inspection or survey
procedures (where otherwise required) for products to be used in a vessel, MODU or facility intended to be ABS classed or that is presently in
class with ABS. Questions regarding the validity of ABS Rules or the need for supplemental testing or inspection of such products should, in all
cases, be addressed to ABS.
01/08/2014 9:01:15 PM
Page 2 of 2
ANNEX 5
Purchaser:
Project:
2. Limited Warranty
Supplier shall perform its services hereunder in a workmanlike manner and provide any
materials free from general defects in workmanship. The warranty period is (3) years from date
of delivery. Supplier's obligation and Purchaser's sole remedy in the event of any breach in this
warranty shall be to provide replacement materials and/or services of a like kind and manner to
those shown to be defective which are free from any such claimed defect. EXCEPT AS
EXPRESSLY SET FORTH IN THIS PARAGRAPH, SUPPLIER PROVIDES NO FURTHER
WARRANTY AND SHALL HAVE NO FURTHER LIABILITY TO PURCHASOR OR ANY
THIRD PARTY FOR OR RELATED TO THE MATERIALS OR ANY SERVICES
PROVIDED TO PURCHASER PURSUANT HERETO, INCLUDING WITHOUT
LIMITATION ANY CLAIM FOR LIABILITY FOR NEGLIGENCE; SUPPLIER MAKES
AND PURCHASER RECEIVES NO WARRANTIES NOT SPECIFICALLY PROVIDED
HEREIN, EXPRESS, IMPLIED, STATUTORY, OR IN ANY OTHER PROVISION OF THIS
AGREEMENT OR ANY OTHER COMMUNICATION MADE TO PURCHASER; AND
SUPPLIER SPECIFICALLY DISCLAIMS ANY WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE OF ANY SERVICE OR MATERIALS
PROVIDED HEREUNDER.
3. Limitation of Liability; Exclusion of Consequential Damages
The cumulative liability of Supplier to Purchaser for any and all claims or any nature in any
manner relating to the services and/or materials provided hereunder, in contract, tort, or
otherwise, shall not exceed the total amount of all amounts received by Supplier from Purchaser
pursuant to this Agreement within the current calendar year. In no event shall either party be
liable to the other for any consequential, indirect, special, or incidental damages, even if such
party has been advised of the possibility of such potential loss or damage. The foregoing
limitation of liability and exclusion of certain damages shall apply regardless of the success or
effectiveness of other remedies.