Professional Documents
Culture Documents
Issue: A/0715
This document is our property for which we reserve all rights, including
those relating to patents or registered designs. It must not be
reproduced or used otherwise or made available to any third party without
out prior permission in writing.
This document is subject to alterations that result in technical progress.
Disclaimer
Any responsibility or liability for loss or damage in connection with the use of this product and the accompanying documentation is disclaimed by Thrane & Thrane. The information in this manual is provided for information
purposes only, is subject to change without notice, may contain errors or inaccuracies, and represents no commitment whatsoever by Thrane & Thrane. This agreement is governed by the laws of Denmark.
Manuals issued by Thrane & Thrane are periodically revised and updated. Anyone relying on this information
should satisfy himself/herself as to the most current version. Providers with access to Thrane & Thranes Extranet may obtain current copies of manuals at: http://extranet.thrane.com.
Thrane & Thrane is not responsible for the content or accuracy of any translations or reproductions, in whole or
in part, of this manual from any other source.
MF/HF 150W/250W
CONTENTS
0715
1
1.1
1.2
General information
Introduction
Technical data
1-1
1-1
1-1
2
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
2.10
2.11
2.12
2.13
2.14
2.15
2.16
2.17
Installation
Description
Mounting the units
Ground connections
Grounding considerations
Antennas
Power supply
Interconnection of units
Connector mounting instructions
Position and time information
DSC programming
Battery alarm adjustment
Options menu - setting up the system
Factory resetting / MMSI resetting
Enabling the 6 ch scanning DSC Watch Receiver
Enabling the Telex operation
Telex operation
Final installation check
2-1
2-1
2-1
2-6
2-6
2-8
2-11
2-12
2-19
2-20
2-20
2-21
2-21
2-23
2-23
2-24
2-24
2-26
3
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
3.10
3.11
3.12
3.13
Technical description
Control Unit
Transceiver Unit
Control/Intercon module 60-122878
Synth. and DSC WR module 60-122879
RX/EX signal path module 60-122880
PA and Filters module 60-122881
SMPS module 60-122882
Transceiver unit block diagram
Transceiver unit interconnection diagram
Antenna Tuning Unit
Antenna Tuning Unit block diagram
Power control and protection system
Power control and protection system
3-1
3-1
3-1
3-1
3-1
3-2
3-2
3-2
3-3
3-4
3-5
3-5
3-6
3-7
4
4.1
4.2
4.3
4.4
4.5
4.6
Service
Preventive maintenance
Realignment of master oscillator
Software update
Trouble shooting
Power protection
Selftest
4-1
4-1
4-1
4-2
4-2
4-3
4-5
5
5.1
5.2
5.3
5.4
5-1
5-1
5-2
5-4
5-4
0715
MF/HF 150W/250W
General information
1.1 Introduction
The 150W / 250W MF/HF transceiver with integrated DSC and telex is designed for maritime applications
in voluntary as well as compulsorily fitted vessels. It offers simplex and semi-duplex SSB radiotelephone
communication in the maritime mobile frequency bands between 1.6 and 30 MHz. The basic version of
the transceiver include voice, DSC and a dedicated 2187,5kHz DSC watch receiver, forming an ideal
system for MF GMDSS installations. The transceiver can easily be upgraded to include 6 channel
scanning DSC watch receiver, and Telex operation to comply with MF/HF requirements in sea area A3.
The upgrade is done by entering software license codes.
The equipment consists of a compact transceiver control unit, a fully remote controlled transceiver unit
and an automatic antenna tuning unit.
The microprocessor controlled Antenna Tuning Unit automatically matches the impedance of antennas
between 8 and 18 metres in length and requires no presetting at the installation. The typical tuning time
is 1 s. It is designed for outdoor installation and may be located up to 100 metres from the Transceiver
Unit.
The Transceiver Unit contains all receiver and transmitter circuits. The fully protected solid state 150W
/ 250W power amplifier cooled by natural convection matches a 50 ohm antenna system, but is normally
used in connection with the Antenna Tuning Unit. The DSC/Telex modem contains two demodulators,
one connected to the built-in watch receiver for continuous watch on the DSC distress frequency 2187.5
kHz, the other connected to the communication receiver which may be used to keep simultaneous watch
on other DSC frequencies or may be used for telex communication.
The Control Unit is for operation of radiotelephone as well as DSC and telex functions. Use of the
equipment is simple, logic and straight forward. DSC operation is based on the use of soft keys. Guiding
texts are provided and the large display is able to show the contents of a complete call in one screen.
For telex operation the keyboard, printer or data terminal can be connected directly to the control unit.
The equipment is designed for operation from a 24 V battery. With the optional AC Power Supply unit
installed the equipment may be supplied from 115/230 V AC main or emergency supplies with automatic
switch-over to 24 V DC supply in the absence of AC supply voltage. Also optionally battery charger for
AC is available in the product line.
The built-in test facilities and easy-to-replace module design of the equipment simplifies the service
concept.
General
Complies with the relevant IMO performance standards for MF/HF GMDSS equipment, the ITU Radio
Regulations, the ITU-R recommendations and the relevant performance specifications of ETSI and IEC,
in the ITU marine bands.
0715
Operating modes:
Simplex and semi-duplex SSB telephony (J3E), DSC (J2B), AM broadcast reception (A3E) and Telex (J2B).
Frequency range:
Frequency stability:
Normal operating
temperature:
from 0C to +40C.
Extreme operating
temperature:
User-programmable
channels:
1-1
1 General information
MF/HF 150W/250W
User-programmable
stations:
Output power:
Supply voltage:
Power consumption:
Rx, 60W (approx. at 24V DC)
Tx, SSB speech:
Tx, SSB two-tone:
Tx, DSC/TELEX:
Compass safe distance:
250W:
175W
300W
420W
300W
550W
600W
Compass safe distance in accordance with ISO/R 694 are given below
in metres.
Unit
Control Unit
Transceiver Unit
Antenna Tuning Unit
Handset
Cradle
LS4970 Loudspeaker
1.2.2
150W:
Standard
5.4/H
1.2
0.4
0.3
0.3
1.1
2.2
Steering
18/H
0.5
0.2
0.1
0.2
0.7
1.6
Receiver characteristics
General:
Frequency range:
Frequency resolution:
Input impedance:
Rx/Tx :
50 ohm
The Antenna is matched by the antenna amplifier in the Aerial Coupler.
DSC/Telex:
50 ohm
12V DC / 20 mA is available for eventual use of active antenna.
Sensitivity:
Telephony(J3E):
Broadcast (A3E):
DSC/Telex (J2B):
Intermodulation:
30 dBV
above 80 dBV
30 dBV
above 90 dBV
20 dBV
above 80 dBV
Spurious rejection:
Audio output power:
1-2
above 70 dB
Build-in loudspeaker
Optional loudspeaker output 4 W typical with less than 10 % distortion.
Output intended for 8 ohm loudspeaker.
0715
1 General information
1.2.3
MF/HF 150W/250W
Transmitter characteristics
General:
Frequency range:
The ITU marine bands in the frequency range 1605 kHz to 30 MHz
Frequency resolution:
100 Hz.
Output power:
150W:
150W PEP 1.4 dB into 50 ohm Antenna, voice for a duty cycle less than
55% and modulation rate greater than 3 baud.
Reduction to 80W when continuously keyed with duty cycle greater than
55% during 1 min. Automatic power recovery after 1 min.
250W:
250W PEP 1.4 dB into 50 ohm Antenna, voice for a duty cycle less than
55% and modulation rate greater than 3 baud.
Reduction to 100W when continuously keyed with duty cycle grater than
55% during 1 min. Automatic power recovery after 1 min.
Power reduction:
approx. 20 W PEP.
Intermodulation:
Spurious Emission:
1.2.4
General:
Frequency range:
Input impedance:
DSC/Telex:
50 ohm.
12V DC / 20 mA is available for eventual use of active antenna.
Sensitivity:
DSC (J2B):
Intermodulation:
DSC (J2B):
Spurious rejection:
0715
Low power:
below 0 dBV.
Wanted Signal:
Intermod. level:
20 dBV.
above 70BV.
above 70 dB.
1-3
1 General information
1.2.5
MF/HF 150W/250W
General:
Frequency range:
Aerial requirements:
Aerial tuning:
Tuning speed:
0.1 - 8 sec.
Power capability:
Extreme operating
temperature:
1.2.6
DSC:
TELEX:
1.2.7
Class A.
Protocols:
Ships identity:
Navigator interface:
Protocols:
Ships identity:
Control Unit:
CU5100/CU5110:
Transceiver Unit
TU5150/TU5155/TU5250:
Equipment category:
1-4
Width:
Height:
Depth:
Weight:
200 mm (7,9")
100 mm (3,9")
80 mm (3.1")
3.3 kg (7.3 lbs)
Width:
Height:
Depth:
Weight:
390 mm (15.3")
445 mm (17.5")
127 mm (5")
19 kg (41.9 lbs)
Width:
Height:
Depth:
Weight:
290 mm (11.4")
500 mm (19.7")
80 mm (3.1")
3.3 kg (7.3 lbs)
Control Unit:
Transceiver Unit:
Antenna Tuning Unit:
Protected,
Protected,
Exposed.
0715
MF/HF 150W/250W
Installation
2.1 Description
Correct installation of the equipment is important for maximum performance and reliability. Antennas and
earth connections must be installed with the greatest care using corrosion resistant materials.
Cable routing shall be made so the cables are protected from physical damage. Sharp cable bends
especially on coaxial cables must be avoided and a sufficient number of clips or straps should be used
to secure the cables.
140
100
200
100
235
40536A
0715
2-1
2 Installation
MF/HF 150W/250W
Mounting option
Drilling plan
7.00
55.00
41.00
4 x 4
14.50
181.00
209.00
Tilting +/-45
Handset
AUX
SCAN-BUS
Keyboard
40615
Data
Printer
40616
Weight:
Control Unit
1.4 kg.
Mounting Bracket 0.3 kg.
Handset for Control Unit
75
This Handset has a hook-on/off function,
which is activated by a small magnet embedded
in the ceadle.
The cradle must be installed as illustrated in
order to ensure the hook-on/off functionality
of the Handset.
min. 200
62
135
226
45
Drilling plan
54
* 120
Space for handset access
39655B
Weight:
Handset for Control Unit 0.4 kg
Dimensions are in mm
2-2
0715
2 Installation
MF/HF 150W/250W
145
391
88
430
350
4 x 8
Cable fitting
360
37955A
56
70
57.6
Cable fitting
12
80
38417
Dimensions are in mm
0715
2-3
2 Installation
MF/HF 150W/250W
80
290
200
76.5
1)
6 x 6.50
145
75
170
12
164
352
164
2)
3)
50
271
37978
2-4
0715
2 Installation
MF/HF 150W/250W
45.5
Drilling Plan
12
67.25
104.5
4 x 4.7mm
196
9.7
176.6
38419
Weight:
CB4616
0.6 kg.
X2 (1. Handset)
X3 (2. Handset/CRY)
45.5
X1 (Control Unit)
12
67.25
104.5
4 x 4.7mm
196
9.7
176.6
38387
Weight:
CB4618
0.6 kg.
Dimensions are in mm
CB4616 and CB4618 may be ordered as accessory. Please find accessory list on the last page of this
manual.
0715
2-5
2 Installation
MF/HF 150W/250W
20
6.6
50
80
11mm
crimp
wire
5.4mm
37836
The ground connection between the ATU and earth ground plane.
The ground connection of the TU and the externally connected equipment.
2-6
Not OK installation
'Hot' Handset
TU
ATU
Zg
CU
RF current loop
Ground-Plane
37867
0715
2 Installation
MF/HF 150W/250W
Antenna start
The vertical antenna always start at its electrical ground-plane, whether or not it is physically mounted
there. First determine the antennas electrical ground-plane, which is where the ATU must be mounted.
Where possible always take the ATU to the ground, not the ground to the ATU.
In case of a fibreglass boat, the ground-plane may well be at the hull grounding terminal. Then this is where
the Antenna Tuning Unit should go and this is where the antenna actually starts.
OK installation
ATU
Ground-Plane
The antenna starts here
37868
RF ground loop
It is not always possible or practical to mount the ATU using a very short strap to the actual ground-plane.
In such a case the coaxialcable may be connected between units with different ground potentials causing
RF loop-current to flow.
Not OK installation
TU
ATU
CU
coaxial cable
Vg = Iant x Zg
Zg
RF current loop
Ground-Plane
37869
OK installation
TU
ATU
CU
Vg = Iant x Zg
Zg
coaxial cable
Ground-Plane
37870
0715
2-7
2 Installation
MF/HF 150W/250W
2.5 Antennas
Transceiver Antenna
The equipment is used with common transmitting and receiving antenna. The antenna should be erected
in the open, away from conducting object such as derricks etc. which may cause reduction of the radiated
power. Insulators should be of the best type having low leakage even when wet. Stays, wires, steel masts
etc. should be either effectively earthed or insulated. The antenna should also be kept as far away as
possible from electrical equipment in order to minimize noise. Electrical installation such as cable braiding
(screens) and instruments in the vicinity of the antenna should be earthed effectively, and the instruments
in question should be fitted with noise-interference suppression devices, effective in the range 0.1 MHz
to 30 MHz to avoid malfunction of these instruments. The Antenna Tuning Unit will tune on any frequency
in the range 1.6 to 27 MHz to good whip and/or wire installations of 12 to 18 meters total electrical length.
Shorter antennas, electrical length down to 8 meters can be used. Where possible long antennas should
be installed to maximize the radiated power in the lower frequency bands.
In general a 12 meter antenna installation can be made using an 8 meter whip and 4.5 meter feeder or
a 10 meter whip and 2.5 meter feeder. In both cases the whip should be mounted on a pole allowing for
the feeder to be erected at an angle of no less than 60 degrees to create a vertical antenna system. Using
horizontal feeders or feeders mounted at an angle below 45 degrees usually transform the antenna
radiation resistance to a lower value reducing the radiated power. Furthermore, the total antenna system
should be kept well away from conductive objects such as the mast. Usually a horizontal distance of more
than 4 meters will create good results.
Note: If a whip antenna is used this should have an anti-corona ball as a top termination to prevent
crackling noise in the receiver.
2-8
0715
2 Installation
MF/HF 150W/250W
0715
2-9
2 Installation
MF/HF 150W/250W
Optional an ATU Mounting Kit may be supplied as shown below. The kit exists in two versions:
1
2
For mounting the ATU directly on a mast, where the Mounting Plate and fittings for mast can form
a sufficient earth connection on a steel mast welded to the superstructure.
To get an even mounting surface on an uneven support.
Treadrod M10
64.005
Mountingplate
237218
1
2
3
4
5
Nut M10
Tooth lock washer M10
Fitting for mast
Mountingplate for ATU
Treadrod M10
2-10
0715
2 Installation
MF/HF 150W/250W
60mm
screen (twisted)
conductor (twisted)
plastic cover
screw
clamp
cable fitting
plastic house
37835
0715
Recommended cable
External fuses
battery *
Screened multiwire
5m
3 x 10 mm2
40 A
8m
12 m
3 x 16 mm2
3 x 25 mm2
50 A
63 A
2-11
2 Installation
MF/HF 150W/250W
SCANBUS
1
SYS
1
SUPPLY ALARM
DSC RX
RX/TX
24 V DC
37849
Handset
AUX
SCAN-BUS
Keyboard
Data
Printer
40616
40631
2-12
0715
0715
40669
External
DSC
Alarms
(optional)
Distress
Alarm
Panel
(optional)
GPS
speaker
8
)
***Loud
Option
Handset
11
*)
**)
***)
4 x 0.5 mm2
10
4x 0.5 mm2
2 x 0.5 mm2
2 x 0.5 mm2
*)
AUX
*)
Dsub
9
male
14
PS2
Keyboard
13
Dsub
9
male
SCANBUS
GND
Keyboard
Printer
Option 1
Dsub
25
male
Printer
12
Dsub
9
male
Data
Data
Terminal
Keyboard
Printer
Option 2
Either option 1
or option 2
5 x 2 x 0.5 mm2
*)
Please note that for distance less than 25m the system will work with 0.25mm instead of 0.5mm.
16
17
Dsub
9
male
4 x 0.5 mm2
*)
Supply
(optional)
AC
**)Power
15
Dsub
9
male
SUPPLY
ALARM
*)
SYS
15
18
Dsub
9
male
24 V
Battery
PL259
DSC RX
RG-213/U
PL259
RX/TX
Transceiver Unit
SCANBUS 24 V DC
Please check the accessory list to find the optional DSUB to screw Terminal Converter Box CB4616.
Dsub
9
male
Handset
Control Unit
Charger
TX
inhibit
(optional)
Data
Modem
etc.
(optional)
)
**Battery
RG-213/U
RX/TX
Antenna
Tuning
Unit
7
2 Installation
MF/HF 150W/250W
2-13
2 Installation
MF/HF 150W/250W
Designation
Remarks
Dsub 9
1
TLF
Handset earpiece
GND
System ground
3
4
5
6
7
8
9
GND
MIC
PTT
HOOK
+8V
nc
2182 SEL
System ground
Handset microphone
Transmit key
Low when on hook
8 V supply to handset
No connection
OC output. Low when 2182 kHz is
selected
Transceiver
Twisted
SCANBUS
SCANBUS
pairs
Dsub 9
Dsub 9
DATA+
Data communication between units. CAN bus. Baud rate: 125 kbps
DATA-
4
5
4
5
AF +
AF -
6
7
8
9
6
7
8
9
GND
+24 V
RX AF +
RX AF -
Shield
Shield
Screen
1
2
Designation
Remarks
SUPPLY ON Supply on signal to the Transceiver Unit. Active when connected to GND
TX AF modulation
Vnom = 0.775 Vrms diff.
Vmax = 12 Vpp diff.
System ground
Supply voltage for the Control Unit.
RX AF signal
Vnom = 0.775 Vrms diff.
Vmax = 12 Vpp diff.
Screen connected to system ground
2-14
0715
2 Installation
MF/HF 150W/250W
Alarm Panel
Designation
Cable no.:
Remarks
SPARC-BUS+
10
Dsub 9
1
Dsub 9
DISTRESS ALARM
11
11
9
MF/HF x4
3
GND
System ground
SPARC-BUS-
10
+24 V*
10
NMEA IN+
EXT_SP+
Shield
Screen
External speaker
Screen connected to system ground
* Fused
0715
2-15
2 Installation
MF/HF 150W/250W
Direction
Designation
Dsub 25
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
Output
Output
Output
Output
Output
Output
Output
Output
Output
Input
Input
Input
Input
Output
Input
Output
Output
LPT_STR
LPT_D0
LPT_D1
LPT_D2
LPT_D3
LPT_D4
LPT_D5
LPT_D6
LPT_D7
LPT_ACK
LPT_BUSY
PAPER END
LPT_SELECT
AUTO LINE FEED
LPT_ERROR
LPT_INIT
LPT_SELIN
GND
GND
GND
GND
GND
GND
GND
GND
Designation
Remarks
Mini DIN(PS2)
1
2
3
4
5
6
PC_KEYB_CLK
GND
PC_KEYB_DATA
NC
+5V
NC
Keyboard clock
System ground
Keyboard data
No connection
5V supply voltage to keyboard
No connection
2-16
0715
2 Installation
MF/HF 150W/250W
Designation
Remarks
Dsub 9
1
nc
No connection
DATA OUT
RS232
3
4
DATA IN
DTR
RS232
GND
System ground
nc
No connection
nc
No connection
nc
No connection
nc
Shield
Screen
RS232
No connection
Screen connected to system
Cable type
External fuses
5m
3 x 10 mm2
40 A
8m
12 m
3 x 16 mm2
3 x 25 mm2
50 A
63 A
Designation
Remarks
Dsub 9
0715
nc
No connection
nc
No connection
3
4
nc
/AC ALR
5
6
7
8
9
Shield
GND
VBATVBAT+
nc
nc
Screen
No connection
AC Alarm input. Alarm when
connected to GND
System ground
Voltage input for high/low battery
voltage alarm
No connection
No connection
Screen connected to system ground
2-17
2 Installation
MF/HF 150W/250W
Designation
Remarks
Dsub 9
1
EXT KEY
2
3
4
5
6
8
9
Shield
2-18
0715
2 Installation
MF/HF 150W/250W
Contact arrangement
(Viewed from solder side)
9
8
7
6
5
4
3
2
1
PL 259
28.5mm
16mm 1.5mm
Coupling nut
Body
0715
2-19
2 Installation
MF/HF 150W/250W
NMEA IN +
NMEA IN -
37871
Interconnection between devices may be by means of two-conductor shielded twisted-pair wire. Multiple
listeners may be connected to a single talker. The receivers are connected in parallel. The shield should
be connected to the navigator chassis and should not be connected at any listener. However the shield
should be continuous (unbroken) between all listeners.
Following sentences are recognized by the equipment for extraction of position and associated time
information: RMC, GLL, GGA. GLL sentences with and without time information is recognized, time
information is extracted if present.
ZDA, RMC, GLL and GGA sentences are recognized by the equipment for extraction of UTC time
information for automatic setting of the internal real time clock.
2-20
0715
2 Installation
MF/HF 150W/250W
0715
Menu
Submenu
Level1
OPTIONS
TX BANDS
Submenu Level 2
EDIT
Select band
CONFIGURATION LSB MODE,
REMOTE MODE,
BATTERY ALARM,
ATU INSTALLED
RX MUTE MODE
TX INHIBIT MODE
AM TX MODE
DSC
LANGUAGE
Select language
RX TEST
TX TEST
SEND B
FACTORY RESET
MMSI RESET
2-21
2 Installation
MF/HF 150W/250W
Notes:
TX BANDS:
CONFIGURATION:
LSB MODE:
4000.0
4438.0
6525.0
8815.0
13200.0
17410.0
18900.0
19800.0
22855.0
25210.0
26175.0
kHz
kHz
kHz
kHz
kHz
kHz
kHz
kHz
kHz
kHz
kHz
When enabled selection of LSB (Lower Side Band) is possible with the MODE key
on the front panel.
Note: LSB mode is normally not allowed for marine equipment.
Factory default setting: Disabled.
REMOTE MODE:
When enabled selection of SSB REMOTE is possible with the MODE key on the
front panel, allowing remote control via the SYS connector of frequency, mode and
power level.
Factory default setting: Disabled.
BATTERY ALARM:
When enabled the voltage at the VBAT input of the SUPPLY ALARM connector
is monitored and an alarm is given by the Control Unit if the voltage is outside the
set range.
Factory default setting: Disabled.
ATU INSTALLED:
When enabled supply voltage and control signals for the ATU is present at the TX/
RX connector. When disabled a 50 ohms antenna or dummy load may be
connected to TX/RX.
Factory default setting: Enabled.
RX MUTE /
TX INHIBIT:
AM TX MODE:
DSC:
LANGUAGE:
Select RX mute or TX inhibit to select functionality of input pin (SYS con pin 4
on transceiver). When RX mute is selected this input will mute the receiver when
input is pulled low. When TX Inhibit is selected this input will prevent keying the
transmitter when input is pulled low. Factory default setting: TX inhibit.
When AM TX is enabled it will be possible to transmit in AM mode with reduced
power.
Note: AM TX mode is only allowed in connection with equipment typeapproved in
accordance with FCC.
Factory default setting: Disabled.
Factory default setting: English.
RX TEST:
When enabled decoded call sequences are routed to the RS-232 port of the SYS
connector. Baud rate: 2400 baud. Parity/data bits: Odd/8.
Factory default setting: Disabled.
TX TEST:
For generation of continuous B or Y signal and dot pattern. DSC mode must be
selected.
FACTORY RESET:
Choosing this option will reset all user programmable settings to the factory default
settings. MMSI will also be reset.
MMSI RESET:
Choosing this option will only reset the MMSI number. Input new MMSI number
after power up.
0715
2-22
2 Installation
MF/HF 150W/250W
0715
2-23
2 Installation
MF/HF 150W/250W
2.16.1
The GMDSS Radiotelex Terminal is an option used for handling transmission/reception of telex
messages over radio. The terminal consists of a printer and a keyboard, connected to the transceiver
control unit which provides the interface to the DSC/telex modem located in the transceiver unit. The
keyboard is equipped with an affixed template for function keys and indicator lamps.
The GMDSS Radiotelex Terminal is designed in accordance with relevant IMO, ITU and ETSI
recommendation/specifications and has been approved for shipboard installations to be operating within
the Global Maritime Distress and Safety System.
It supports world-wide ship-to-ship, shore-to-ship and ship-to-shore communication by utilizing the
radiotelex protocols described in ITU- Rec. 625 to overcome the deficiencies of the HF medium. In case
of two-way communication an ARQ (Automatic Repetition reQuest) algorithm for error correction is thus
used, and when sending to more than one station an FEC (Forward Error Correction) algorithm is used.
2-24
0715
2 Installation
MF/HF 150W/250W
MF/HF DSC Telex Aerial
MF/HF
TU5250
Option
LS4970
CU5100
AP5065
Telex option 1
ATU5215
HF Aerial
Coupler
Power Supply
Option
Data Modem
Telex option 2
H1252B
H1252B
TT-3606E
TT-3601E
TT-3601E
40614
2.16.2
2.16.2.1
Printer
The terminal uses an OKI Microline 280 parallel interface dot-matrix printer with roll paper stand, please
refer to the operation guide delivered with the printer. The printer should be connected to the printer socket
at the rear of the control unit by means of the parallel interface cable included with the printer. The printer
is equipped with a special firmware which allows the paper to be scrolled up so the current line can be
read in printing pauses, and scrolled back down when printing continues. The firmware version can be
checked by performing a selftest: Disconnect the parallel interface cable. Press the LF (line-feed) and the
Select button while switching the printer on. When light comes on in the indicator lamps, release the
buttons. The printer version is now printed followed by a test print-out. The version must be: F/W 03.10
Also make sure the printer firmware is configured for radio telex. This is shown in the snapshot below,
where MEI E1 indicates configuration for radio telex.
Keyboard
The keyboard is a Cherry 1800 PC/AT compatible keyboard. The self-adhesive keyboard template
delivered with the equipment must be mounted on the keyboard: Remove the protective paper. Carefully
place the template around the function keys and indicator lamps so the latter are fully visible.
0715
2-25
2 Installation
MF/HF 150W/250W
Modem Set-up
Modem set-up mode is selected automatically when selecting telex mode on if no call codes are valid or
if the answer back string is not valid. To change a valid set-up, a factory reset of the modem must be
performed.
When entering telex mode after a factory reset the 5-digit call code, may then be entered. The MMSI
number from the control unit will be printed, but cannot be changed. The answer back string allocated to
the station may then be entered. To leave a setting unchanged just press Enter, otherwise key in a new
setting and press Enter. The next item is then printed. After the last item follows:
Accept settings (Y/N)?
The process may be repeated if N is pressed; the modem set-up mode is left if Y is pressed.
The answer back, which should be entered above is combined by the 5-digit call code or MMSI number,
the abbreviated ID and an x e.g.:
12345 abcd x
or
123456789 abcd x
2-26
0715
MF/HF 150W/250W
Technical description
0715
3-1
3 Technical description
MF/HF 150W/250W
An integer type PLL is used for creating the DSC LO1 signal. The PLL resolution is 2 KHz and after
division by 4 the final DSC LO1 resolution is 500 Hz. Three separate VCO s are used for covering
the necessary frequency range. A 14.85 MHz TCXO is used for reference for the PLL.
A doubler Circuit submitted to the 14,85 MHz reference signal is used for DSC LO2 signal thus
creating 29.70 MHz.
A 14.6144 MHz TCXO divided by 32 thus creating 456.7 KHz is used for DSC LO3 signal.
3-2
0715
0715
TU-ATU
Modem
TX/RX
40635
DSC RX
Detector
TX Key &
TX Inhibit
Interface
AF Amp.
600 Ohm
RX AF
Converter
AF Switch
SUPPLY
ALARM
SYS
SCANBUS
24V DC
24V DC to PA
RS-232
CAN
TX SIGNAL
RX SIGNAL
CPU
Filter
AF Switch
SMPS 60-122882
+ 7.5 V
- 15 V
+ 15 V
+ 25 V
CONTROL/INTERCON 60-122878
TX/RX
Switch
AF Amp.
600 Ohm
TX AF
Converter
DSC WR AF
DSC RX AF
RX AF
Switched
Mode
Power
Supply
TX AF
Ant.
Switch
Compressor
45 MHz
Filter
and Gain
455 kHz
Filter
Bank
RX AF
EX SIGNAL
DSC
1700 Hz DSC RX AF
Filter Amp.
Demodulator
PreSelector
Modulator
Antenna
Supply
Protection
Circuit
Ramp
gen.
Sample
hold
PLL
Filter
Frontend
Filter
DAC
Loop
ampl.
1. LO
API
corr.
X5
VCO
PLL
VCO
Divide
by 4
32 - 46 MHz
Prescaler
VCO
Band
select
Filter
VCTCXO
14.8500 MHz
2. LO
PLL
3. LO
LP Filters
X2
29.7 MHz
OCXO
and
Dividers
IF2
AGC amp.
VCTCXO
14.6641 MHz
Divide
by 32
456.7 kHz
Hard
Limiter
DSC WR AF
DSC AF
filter
1700Hz
AGC
generator
3 Technical description
MF/HF 150W/250W
3-3
DSC RX
DSC RX
TX/RX
AC ALR
GND
VBATVBAT+
X2
RX SIGNAL
X9
TX SIGNAL
GND
ADR0
ADR1
ADR2
ADR3
DATA0
DATA1
DATA2
DATA3
DATA4
DATA5
DATA6
DATA7
STROBE
GND
PA KEY
PA TEMP
PA PROTEC
FILPEAK
GND
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
W10
W9
W16
W2
W1
X9
X9
TX SIGNAL
RX SIGNAL
RX SIGNAL
EX SIGNAL
1. LO
2. LO
3. LO
X11
X12
X13
X14
GND
X2
GND
ADR0
ADR1
ADR2
ADR3
DATA0
DATA1
DATA2
DATA3
DATA4
DATA5
DATA6
DATA7
STROBE
GND
-15V
-15V
+15V
+15V
+7.5V
+7.5V
GND
X1
GND
RX AF
TX AF
AGC
MGC/ALC
DSC RX AF
X8
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
W11
X11
TX/RX
1
2
3
4
5
6
7
8
9
SUPPLY
ALARM
EXT KEY
DATA OUT
DATA IN
TX INHIBIT
GND
LINE OUT
LINE IN
TX KEYED
+12V
X8
X5
PA PA PA -
PA 18 PA 19 PA 20 PA+
1
2
EX SIGNAL
W12
W13
W14
W2
W1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
7
8
9
10
11
12
13
14
15
16
17
18
19
20
X12 1. LO
X13 2. LO
X14 3. LO
X8 RX TELEX
X5 DSC RX
GND
X2
GND
ADR0
ADR1
ADR2
ADR3
DATA0
DATA1
DATA2
DATA3
DATA4
DATA5
DATA6
DATA7
STROBE
GND
-15V
+15V
+15V
+7.5V
+7.5V
GND
X1
DSC WR AF
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
1
2
3
4
5
6
7
8
9
60-122878
CONTROL/INTERCON
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
W5
W4
X4
PA+
PA+
PA+
PA+
18 PA+
19 PA+
20 PA -
1
2
X3
GND
GND
GND
GND
GND
GND
GND
SUPPLY OFF
SUPPLY ON
BATINFO
+25V
+25V
+25V
-15V
-15V
+15V
+15V
+7.5V
+7.5V
GND
X2
7
8
9
10
11
12
13
14
15
16
17
18
19
20
SYS
SUPPLY ON
DATA+
DATAAF+
AFGND
+25V
RX AF+
RX AF-
X1
GND
RX AF
TX AF
AGC
MGC/ALC
DSC RX AF
DSC WR AF
SUPPLY OFF
SUPPLY ON
BATINFO
+25V
+25V
+25V
-15V
-15V
+15V
+15V
+7.5V
+7.5V
GND
PA PA - 18
PA - 19
20
PA+
PA - 1
PA - 2
PA -
X5
PA+
PA+ 18
PA+ 19
PA - 20
W3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
GND
ADR0
ADR1
ADR2
ADR3
DATA0
DATA1
DATA2
DATA3
DATA4
DATA5
DATA6
DATA7
STROBE
GND
PA KEY
PA TEMP
PA PROTEC
FILPEAK
GND
1
2
3
4
5
6
7
8
9
X4
PA+ 1
2
PA+
PA+
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
X1
40636
3-4
SUPPLY OFF
SUPPLY ON
BATINFO
+25V
+25V
+25V
-15V
-15V
+15V
+15V
+7.5V
+7.5V
GND
SCANBUS
24V DC
+
-
SMPS 60-122882
X3
GND
GND
GND
GND
GND
GND
GND
SUPPLY OFF
SUPPLY ON
BATINFO
+25V
+25V
+25V
-15V
-15V
+15V
+15V
+7.5V
+7.5V
GND
3 Technical description
MF/HF 150W/250W
3 Technical description
MF/HF 150W/250W
5V
regulator
to digital
circuits
13/24V
SMPS
control by
uP
to relays
RX amplifier
Rx
Amp
24V
to relays
RF filter
RX/TX/
ATU/COM
24V DC
Antenna
Tuning circuit
Directional
Coupler
26dB
rx
tx
IL detector
L-bank
Ic
detector
Modem filter
CB1
control by
uP
Iant. detector
Antenna
Connector
Horn
CB2
Vref
Demodulator
L-bank
Vw
control
Rx/Tx
Modulator
Phase &
Voltage
Detectors
control
banks
current
detectors
Micro Prosessor
Temperature
sensor
40637
0715
3-5
3 Technical description
MF/HF 150W/250W
3-6
0715
0715
40638
Power
Supply
Det.
SMPS 60-122882
BATINFO
MGC/ALC
EX SIGNAL
PA TEMP
Temp.
Sens.
A/D
Converter
CPU
FILPEAK
TX SIGNAL
Peak Det.
Average Det.
Peak Det.
Comparator
Protect.
Det.
PA peak
Det.
PA PROTEC
LP Filters
SWR
Det.
D/A
Converter
V+I Det.
RX SIGNAL
ATU-TU
Com
Demodulator
TU-ATU
Com
Modulator
24V DC
CONTROL/INTERCON 60-122878
TU-ATU
Coax
24V DC
ATU-TU
Com
Modulator
TU-ATU
Com
Demodulator
SWR
Det.
CPU
Current
Det.
Temp.
Sens.
Current
Det.
Current
Det.
3 Technical description
MF/HF 150W/250W
3-7
MF/HF 150W/250W
Service
The condition of the battery should be checked at frequent intervals. The battery must always be
fully charged and should be topped up frequently with distilled water (liquid should be 5 to 10 mm
above the plates).
2.
Check the condition of antenna installation, ground connection and cables at regular intervals.
3.
4.
Ensure that no objects are obstructing the free airflow through the cooling fins of the Transceiver
Unit and keep the units free of dust accumulation to prevent overheating.
5.
For cleaning use a damp cloth. Sticky dirt may be removed using a cloth with a weak soap solution.
Wipe off with a clean cloth.
Measuring Equipment:
Frequency Counter:
2.
Preparations:
2.1
2.2
2.3
2.4
3.
0715
Locate the Master Oscillator adjustment hole in the metal cover over SYNTH.AND DSC WR
module 60-122879. Use a small screwdriver to gently adjust the frequency.
Adjust the frequency as close as possible to 44.544 000 MHz.
Adjustment tolerance +/-1Hz.
Remove the counter probe and refit the front of the Transceiver Unit.
4-1
4 Service
MF/HF 150W/250W
4.3.1
Setup
In order to perform a software update, a PC with a communication program (e.g. Procomm Plus or
HyperTerminal) and a communication cable are required.
If the Hyper Terminal program is used it is recommended to close and re-start the program if more than
one file has to be downloaded. This should be done between each file download.
4.3.2
PC
Value
38400
None
8
1
4.3.3
Cable
The cable must be a 3-wire cable. Supplying more than 3-wire may damage the PC. The PC side of the
cable must be a 9-pin (or 25-pin) female D-sub connector; the CU/TU side must be a 9-pin male D-sub
connector. The cable may be supplied as accessory.
Designation
PC
Com port
9-pin
25-pin
Received Data
2
3
Transmitted Data
3
2
Ground
5
7
4.3.4
CABLE
CU
Aux
9-pin
2
3
5
TU
Sys
9-pin
2
3
5
Designation
Data Out
Data In
Ground
Procedure
The PC with the communication program and cabling must be ready before the CU/TU is switched on.
The procedure is as follows.
Download software from the web site or receive it from your distributor if necessary.
Switch off PC and CU/TU
Connect cable to unit to be updated
Switch on PC
Enter the communication program. Setup the Com port and select X-Modem protocol. Select the
upload file (the new software version) and begin uploading.
Switch on the CU/TU.
Upload will now begin. The result of the upload will be written on the PC when the upload is finished. If
the upload was successful the CU/TU reboots automatically.
Any software update should always be followed by Factory Reset as described in section 2.13.
Check the hardware configuration of the transceiver by selecting MENU and the INFO & TEST,
INFORMATION, VERSION and HARDWARE menu items, in particular check that the antenna
tuning unit is recognized, if installed.
2.
If the malfunction is related to transmission check the current status of the power and protection
monitor. A description of the Protection codes is included on the following pages.
4-2
0715
4 Service
MF/HF 150W/250W
3.
If possible execute the built in self test. An Error code for the failing module will be displayed. A
description of the Error codes is included in the Self Test section of this chapter.
4.
If an execution of the self test failed, check that all cables and plugs are correctly connected, and
that the supply voltage is correct. At this point the fuses should be checked.
5.
6.
a.
b.
Check that the +5 V LED (Light Emitting Diode) V1 on the PA AND FILTERS module
60-122881 is constantly on; indicating that the Switch Mode Power Supply is on and
producing +7.5 V DC.
If the above steps did not help, please contact your local service agent.
A list of service agents is found on the Internet.
Group
00
10 - 17
20 - 23
40 - 51
No protection set
TU power regulation problems. Perform a Self Test.
TU hardware protection.
ATU protection.
No protection active !
10
Measurement:
Protection made:
Possible cause:
11
Measurement:
Protection made:
12
Measurement:
Protection made:
0715
4-3
4 Service
MF/HF 150W/250W
13
Measurement:
Protection made:
Supply failure
Supply voltage higher than 33 V
TX key inhibited.
Note: It is necessary to press TUNE to reset the protection.
14
Measurement:
Protection made:
15
Measurement:
Protection made:
16
Measurement:
Protection made:
17
Measurement:
TU-ATU Failure
CONTROL/INTERCON module 60-122878 measures too high power output.
ATU requests lower output power and TU has reached minimum.
Automatic power regulation inhibited.
Low Power High
CONTROL/INTERCON module 60-122878 measures too high power output.
Low Power was too high.
Power set as Low as possible.
Protection made:
20
Measurement:
Protection made:
Possible cause:
PA Temp
PA temperature too high.
Output power decreased.
Free airflow through the cooling fins of the Transceiver Unit impaired.
21
Measurement:
Protection made:
Possible cause:
PA SWR high
PA SWR was too high.
Reflected power was detected.
Output power decreased.
TU - ATU coaxial cable or antenna.
22
Measurement:
Possible cause:
High Average
Average power reduced to 100W.
CW keyed for more than 1 minute.
23
Measurement:
Protection made:
Possible cause:
PA Hot
PA temperature continuously high.
Key inhibit for 5 min.
Free airflow through the cooling fins of the Transceiver Unit impaired.
25
Measurement:
Protection made:
Possible cause:
PA SWR
PA SWR was high.
Output power reduced to safe limits.
High SWR or change in antenna impedance.
40
Measurement:
Protection made:
Possible cause:
Not Tuned
ATU failed tuning the antenna.
ATU selects feed through setting.
Antenna installation.
41
Measurement:
Protection made:
Possible cause:
No Tune Power
ATU measured no tune power.
ATU selects feed through setting.
TU - ATU coaxial cable shorted.
4-4
0715
4 Service
MF/HF 150W/250W
42
Measurement:
Protection made:
Possible cause:
Bad SWR
ATU measured SWR > 8 during Tune Procedure.
ATU selects feed through setting.
Bad antenna impedance on the selected frequency.
43
Measurement:
Possible cause:
High SWR
ATU measured SWR >3 but <8 during Tune Procedure.
Poor antenna impedance on the selected frequency.
44
Measurement:
Possible cause:
V or I
ATU measured that the maximum voltage or current rating is reached
during ALC adjustment.
A short antenna and a low frequency.
45
Measurement:
Possible cause:
Temp
ATU requests for lower power during TX.
Temperature inside ATU cabinet is too high.
46
Measurement:
Possible cause:
Bad SWR TX
ATU measured SWR > 8 during transmission.
Bad antenna impedance on the selected frequency.
47
Measurement:
Possible cause:
High SWR TX
ATU measured SWR >3 but <8 during transmission.
Poor antenna impedance on the selected frequency.
48
Measurement:
V or I high TX
ATU measured that the maximum voltage or current rating is reached
during transmission.
A short antenna and a low frequency.
Possible cause:
50
Measurement:
Possible cause:
V or I high
ATU measured that the maximum voltage or current rating is reached
during ALC adjustment and the power had to be reduced more than 6 dB.
A bad antenna and a low frequency.
51
Measurement:
Protection made:
Possible cause:
4.6 Selftest
Introduction
The SELF TEST BITE (Built-In Test Equipment) of the transceiver is used as a fault diagnosing tool for
the service technician. It may also be used by the operator to obtain additional information on a problem
when ordering service.
The SELF TEST checks the vital functions of the Transceivers modules by performing and monitoring
a sequence of operations. The program controls the analog and digital set ups necessary to perform each
test step in the line of tests executed during the SELF TEST. These set ups will result in a digital feed
back from go/no-go analog check detectors, A/D converters or digital circuits.
Self test description
The SELF TEST is started by selecting MENU and the INFO &TEST, CHECK, SELFTEST menu items.
All tests which does not involve transmission will automatically be performed successively until the last
test has passed or an error condition has occurred. The test number and a name is displayed as the test
proceeds.
After the last test the user has the option to continue with a test of the transmitter with power delivered
to the antenna. The user selects the test frequency. Both receiver and transmitter are set to the test
frequency which should be selected so as to cause minimal disturbance of others.
0715
4-5
4 Service
MF/HF 150W/250W
If stopped due to an error condition, an error code is displayed. Only one error code is given as a result
of each test (the lowest number fitting). The user has the option to repeat the test or cancel.
It is also possible to select a single test step for service purposes. Tests may be repeated several times
giving a technician the opportunity to make measurements. Note that test on an arbitrary test number may
provide a false indication to where the problem is, as the self test assumes that all previous test steps have
been performed and found OK.
Explanations to the Error codes are listed on the following pages.
Test 1 - CU RAM
A write/read test is performed on the Random Access Memory in the Control Unit.
Error code
Conditions
Possible error sources
0101
CU RAM failure
CONTROL UNIT
Test 3 - TU RAM
A write/read test is performed on the Random Access Memory in the Transceiver Unit.
Error code
Conditions
Possible error sources
0301
TU RAM failure
CONTROL/INTERCON module 60-122878
Test 6 - MMSI
The CU checks that the MMSI has been programmed and that transfer to the modem has been
successful.
Error code
Conditions
Possible error sources
0601
MMSI not programmed
Programming left out
0602
MMSI not transferred to TU
ScanBus cable or CONTROL UNIT
or CONTROL/INTERCON 60-122878"
4-6
0715
4 Service
MF/HF 150W/250W
Test 8 - 2. LO
2. LO is checked for signal.
Error code
Conditions
0801
2. LO CHECK = No signal
0715
Conditions
1. LO CHECK = Lock
4 Service
MF/HF 150W/250W
4-8
0715
4 Service
MF/HF 150W/250W
4-9
4 Service
MF/HF 150W/250W
Test 34 - SQUELCH
The squelch circuit of the RX/EX Signal Path 60-122880 is checked in SSB mode. By choosing the proper
synthesizer frequencies the signal passes the 45 MHz filter and is mixed to a 500 Hz tone in the audio
part. This makes the squelch open. Then a 2 kHz tone is generated making the squelch close. Squelch
hold time is also checked.
Settings:
Band: 45 52.5 MHz
1. LO: 44.99900 MHz
a)
3. LO: 455.50 kHz (500Hz tone)
b)
3. LO: 457.00 kHz (2 kHz tone)
Error code
Conditions
Possible error sources
3401
RX AF CHECK 515 = No signal
RX/EX SIGNAL PATH module 60-122880
with 500 Hz tone.
3402
RX AF CHECK 515 = Signal
RX/EX SIGNAL PATH module 60-122880
with 2 kHz tone.
3403
Squelch hold time not ok.
RX/EX SIGNAL PATH module 60-122880
Test 35 - RX AGC
The gain control circuit of the RX/EX Signal Path 60-122880 is checked . By choosing the proper
synthesizer frequency the signal passes the 45 MHz filter and is mixed to a 1 kHz tone in the audio part.
By setting the MGC voltage to low sensitivity the RX AF Check should indicate no AF signal. By setting
the MGC voltage to high sensitivity the RX AF Check should indicate AF signal present.
Settings:
Band: 45 52.5 MHz
1. LO: 44.99900 MHz
3. LO: 456.00 kHz
Error code
Conditions
Possible error sources
3501
RX AF CHECK 515 = Signal
RX/EX SIGNAL PATH module 60-122880 or
with MGC voltage at max.
CONTROL/INTERCON module 60-122878
3502
RX AF CHECK 515 = No signal
RX/EX SIGNAL PATH module 60-122880 or
with MGC voltage at min.
CONTROL/INTERCON module 60-122878
0715
4 Service
Error code
3601
3602
3603
MF/HF 150W/250W
Conditions
Possible error sources
No AGC voltage with signal on RX/EX SIGNAL PATH module 60-122880 or
CONTROL/INTERCON module 60-122878
Hang time too short
RX/EX SIGNAL PATH module 60-122880 or
CONTROL/INTERCON module 60-122878
Hang time too long
RX/EX SIGNAL PATH module 60-122880 or
CONTROL/INTERCON module 60-122878
[Test 39 - reserved]
[Test 40 - reserved]
Test 41 - EX TUNE CW
The exciter of the RX/EX Signal Path 60-122880 is checked in Tune CW mode. PA and Filters 60-122881
is not keyed. The exciter is set to produce a 15 MHz carrier. No AF input signal. RF should be detected
at the exciter output.
Settings:
Band: 60 67.5 MHz
1. LO: 60.00000 MHz
3. LO: 456.50 kHz
Error code
Conditions
Possible error sources
4101
EX CHECK = No signal
RX/EX SIGNAL PATH module 60-122880
0715
4-11
4 Service
MF/HF 150W/250W
Test 42 - EX ALC
The Automatic Level Control on the RX/EX Signal Path 60-122880 is checked. PA and Filters 60-122881
is not keyed. The exciter is set to produce a 15 MHz CW carrier. No AF input signal. Low and high ALC
level. No RF should be detected at the exciter output with low ALC level. RF should be detected with high
ALC level.
Settings:
Band: 60 67.5 MHz
1. LO: 60.00000 MHz
3. LO: 456.50 kHz
Error code
Conditions
Possible error sources
4201
EX CHECK = Signal
RX/EX SIGNAL PATH module 60-122880 or
with ALC low
CONTROL/INTERCON module 60-122878
4202
EX CHECK = No signal
RX/EX SIGNAL PATH module 60-122880 or
with ALC high
CONTROL/INTERCON module 60-122878
[Test 44 - reserved]
[Test 45 - reserved]
Test 46 - TX
The user may enter a test frequency and listen for signals to ensure that the frequency is free, before the
transmitter tests are carried out.
PA and Filters 60-122881 and ATU Module 60-122883 is checked. A full tune and ALC procedure is
performed on a frequency chosen by the user. Then a transmission with full power is carried out for 10
seconds, followed by a transmission in low power mode also lasting 10 seconds.
Error code
Conditions
Possible error sources
4610
Tune power low
W1 or W2 or W8 or W11
4611
Tune power high
W1 or W2
4612
ALC power high
W1 or W2
4613
Supply failure
W1
4614
ALC power low
W1 or W2
4615
TU ATU failure
Coax cable TU ATU or Antenna installation or W15
or ATU
4616
Low power high
W1 or W2
4617
Full power high
W1 or W2
4620
PA temperature high
PA AND FILTERS module
4621
PA SWR high
Antenna installation or
PA AND FILTERS module
4640
Not tuned
Antenna installation or ATU
4641
No tune power
CONTROL/INTERCON module 60-122878 or W15
or
Coax cable TU ATU shorted or ATU
4642
Bad SWR
Antenna installation or ATU
4646
Bad SWR TX
Antenna installation or ATU
4-12
0715
MF/HF 150W/250W
Loosen 4 screws
Screw A2 M6x30mm,
87.838
Hinge Bolt,
11.4 x 27mm
238107
0715
Hinge Bolt,
11.4 x 27 x 54.5mm
238106
5-1
40633
C95
E1
C254
H39
C18
C255
C149
H38
V33
C17
R160
H49
H48
H47
C40
R101
C253
C210
L8
H9
X3
H37
W3
X3
H26
K8
C19
C2
C1
C238
H19
C183
C175
C182
C176
C28
C27
L12
C179
C178
X7
S1
C90
L11
C89
T3
C94
C171
C170
H5
C173
H6
C172
R121
C30
C22
C242
C23
C29
R118
R38
R37
C108
H42
H41
R119
C109
V6
H44
H43
V7
C301
C58
R120
C309
V57
V58
C110
R62
R62
R79
R163
C85
H22
C205
V27
C45
H8
L5
C111
C31
C32
C34
C33
C112
K10
C307
R87
C300
C308
C299
C51
R167
L7
H23
C43
C42
C41
R44
R47
T2
L9
R45
C114
C50
C211
R142
C120
C75
C298
C297
C77
C117
C296
C118
C76
C294
K12
C177
H21
C44
C169
C52
C24
R174
H7
H45
H46
C25
R122
V36
C277
R170
C284
C126
C55
R63
V34
C248
V40
V35
C250
V4
R43
R42
R124
C283
V5
C61
R125
C135
C282
C213
H24
C276
C129
C275
R193
V51
R63
R53
R55
C274
C132
R194
C134
R126
C64
C279
C292
SMPS 60-122882
C224
R57
R99
C187
C204
L31
C295
C290
R117
H18
L20
R51
V28
C12
C48
L3
R46
R49
C36
C35
C37
C38
R50
L2
L42
L40
C49
C185
C184
C234
T1
H11
H15
C201
C174
C156
C9
H20
C70
C202
H28
H29
V63
R171
C270
V62
C127
C264
C263
X17
X16
H10
C225
C140
C144
C223
C71
C137
C136
C271
C269
C93
C68
V3
C233
C232
C3
R89
C267
L51
W4
X4
R180
C220
C222
C221
X4
N1
C265
C266
C219
R150
R180
L1
C239
H30
H31
R137
R136
C8
R5
R20
R21
R6
C7
C6
R7
R22
C5
R8
R23
R181
R102
C124
R182
R164
C123
R12
C141
C237
H12
R10
R17
H16
C268
C241
C236
C4
R11
R210
N13
X8
X8
R82
V50
R85
N3
C67
R208
N12
C157
C158
C159
C160
C161
C162
C243
R84
C54
C69
C153
X11
C235
C208
H13
D3
C11
R48
R206
R100
C113
R191
R192
V54
X11
N10
R141
R177
V53
V42
V37
C189
C199
C195
C193
C191
R94
C59
N4
H35
C197
H33
R153
R31
R151
R152
R29
V49
N11
R127
R128
R129
R161
R130
R131
R132
R169
R140
V30
X5
X5
H32
W5
R215
H27
K9
K3
C88
K13
C91
C87
C66
C305
R105
H25
C16
C13
C15
C14
R154
C92
R106
L10
L13
C334
C249
C335
C20
C304
R104
V41
L32
C286
C82
L21
L22
R36
R35
C291
C306
C303
V25
C26
V19
C78
R111
C73
C288
C116
C83
V18
C302
R103
V24
V20
V69
C21
V23
V21
R97
V22
V68
R162
R54
V56
R73
R34
R32
C81
V2
R133
L30
R176
R168
L4
V26
C147
R58
L6
R72
R30
C115
R39
C74
C125
C122
C80
R109
C287
C289
V31
C72
C278
R123
C280
C164
L41
C293
V14
H17
R66
C285
R40
V15
C186
R64
C46
C167
C79
R110
V52
R93
R107
C142
R108
R28
C166
R67
C139
C65
C62
C281
C131
C146
R165
C56
C273
R60
R76
C39
C63
C272
V29
R81
V72
R68
C246
R65
R188
C245
C252
C138
R198
K11
R74
R135
V16
R113
R172
C84
C143
C145
R115
C244
R173
H40
R184
R52
R59
C47
R61
R27
R114
R156
R185
V61
V32
R204
R41
L50
C10
C329
R134
L52
C60
R86
V60
V59
V11
V10
V9
V8
C262
R112
R4
R183
R16
R9
R211
R15
R209
R213
V38
C330
R14
V13
R116
R175
R90
R56
R3
V46
V45
V39
R2
R214
C168
R159
C206
C152
R179
C207
N6
C154
V47
C203
C228
R186
V64
R158
R157
V67
R195
R92
R139
R91
N5
C99
C107
R95
R155
C150
C148
C209
D1
D4
V43
R25
V17
C121
N2
R75
C165
R196
R201
V1
C155
R149
R148
C226
W7
R197
E3
E2
C214
R199
R80
C229
R178
W6
N9
V66
V65
V44
C240
C200
C194
C192
C190
C188
C196
C198
X2
R178
R13
N7
C227
X1
X100
R143
C151
C181
C57
R83
C119
R1
V12
R205
R96
R78
R207
C247
R88
R98
R166
C212
R77
R33
R146
R138
R18
R19
X2
R26
R71
R145
R24
R187
C163
V55
R144
R70
R69
R147
C216
V71
N8
V70
C215
R212
R200
5-2
R203
R190
R202
R189
C53
V48
H2
H4
H14
H1
W8
TX
W11
EX
- +
W1
24 V DC
W2
W14
3.LO
RX/EX SIGNAL
PATH 60-122880
M0. ADJ
W13
2. LO
SYS
SUPPLY
ALARM
DSC RX
W12
1.LO
RX/TX
W15
W9
RX
SYNTHESIZER AND
DSC WR 60-122879
CONTROL/INTERCON. 60-122878
W16
RX TELEX
SCANBUS
W10
DSC RX
0715
C86
MF/HF 150W/250W
0715
5-3
MF/HF 150W/250W
Slotted screwdriver
Torx screwdriver
PART NO.
405083A
804655xx(*)
8046650006
804656xx(*)
8046660006
405070
804616 (*)
804618 (*)
532506
737589
737588
737822
5-4
0715