Professional Documents
Culture Documents
Edition 1009 / 1
Sikafloor-220 W Conductive
Sikafloor-220 W Conductive
Construction
Product
Description
Sikafloor -220 W Conductive is a two part, water dispersed, epoxy resin with a high
electrostatic conductivity.
Uses
Characteristics /
Advantages
Product Data
Form
Appearance / Colours
Resin - part A:
Hardener - part B:
black, liquid
white, liquid
Packaging
Part A:
Part B:
Part A+B:
4.98 kg containers
1.02 kg containers
6 kg unipacks
Storage
Storage Conditions /
Shelf Life
Technical Data
Chemical Base
Waterborne epoxy
Density
Part A:
1.15 kg/l
Part B:
1.06 kg/l
Mixed Resin:
1.04 kg/l
All density values at +23C.
Solid Content
Electrostatic Behaviour
(IEC 61340-4-1)
Sikafloor-220 W Conductive
1/7
System
Information
System Structure
Primer:
Earthing connection:
Conductive coat:
or 1 x Sikafloor -381 AS
or 1 x Sikafloor -390 AS
Note: This system configuration as described must be fully complied with and may
not be changed.
Application Details
Consumption / Dosage
Coating System
Product
Primer
Consumption
Levelling (optional)
Conductive coat
Wearing course
Sikafloor -262 AS N
Refer to PDS of
Sikafloor -156
~ 2.5 kg/m
~ 0.75 kg/m
2
2
Sikafloor -381 AS
~ 2.5 kg/m
~ 2.5 kg/m
~ 0.15 kg/m
Sikafloor -390 AS
Conductive seal coat
(optional)
These figures are theoretical and does not allow for any additional material due to
surface porosity, surface profile ,variations in level and wastage etc.
Substrate Quality
Substrate Preparation
carried out using appropriate products from the Sikafloor , SikaDur and SikaGard
range of materials.
The concrete or screed substrate has to be primed or levelled in order to achieve
an even surface.
High spots must be removed by e.g. grinding.
All dust, loose and friable material must be completely removed from all surfaces
before application of the product, preferably by brush and/or vacuum.
Sikafloor-220 W Conductive
2/7
Application
Conditions /
Limitations
Substrate Temperature
Ambient Temperature
Substrate Moisture
Content
Dew Point
Beware of condensation!
The substrate and uncured floor must be at least 3C above dew point to reduce
the risk of condensation or blooming on the floor finish.
Application
Instructions
Mixing
Mixing Time
Prior to mixing, stir part A mechanically. When all of part B has been added to part
A, mix continuously for 2 minutes until a uniform mix has been achieved.
To ensure thorough mixing pour materials into another container and mix again to
achieve a consistent mix.
Over mixing must be avoided to minimise air entrainment.
Mixing Tools
Sikafloor -220 W Conductive must be thoroughly mixed using a low speed electric
stirrer (300 - 400 rpm) or other suitable equipment.
Application Method /
Tools
Uniformly spread 1 x Sikafloor -220 W Conductive using a short pile nylon roller
(12 mm).
Cleaning of Tools
Clean all tools and application equipment with water immediately after use.
Hardened and/or cured material can only be removed mechanically.
Potlife
Waiting Time /
Overcoating
Temperatures
Time
+10C
~ 120 minutes
+20C
~ 90 minutes
+30C
~ 30 minutes
Minimum
Maximum
+10C
36 hours
6 days
+20C
24 hours
4 days
+30C
12 hours
2 days
Minimum
Maximum
+10C
26 hours
7 days
+20C
17 hours
5 days
+30C
12 hours
4 days
Sikafloor-220 W Conductive
3/7
Notes on Application /
Limitations
Number of measurements
< 10 m
1 measurement / m
2
10 - 100 m
10 - 20 measurement
> 100m
10 measurements / 100m
Please make sure to only use the original Sikafloor Earthing Kit in order to connect
the earthing points. Every earthing point is able to conduct approx. 300 m, The
earthing points have to be connected to the ring-mains, which has to be carried out
and approved by an electrical engineer and in accordance with any relevant
regulations or standards.
Numbers of earth connections:
Per room at least 2 earthing points. The optimum number of earth connections
depends on the local conditions and should be specified with documents.
If heating is required do not use gas, oil, paraffin or other fossil fuel heaters, these
produce large quantities of both CO2 and H2O water vapour, which may adversely
affect the finish. For heating use only electric powered warm air blower systems.
The incorrect assessment and treatment of cracks may lead to a reduced service
life and reflective cracking - reducing or breaking conductivity.
Sikafloor-220 W Conductive
4/7
Curing Details
Applied Product ready
for use
Temperature
Foot traffic
+10C
~ 26 hours
+20C
~ 13 hours
+30C
~ 8 hours
Value Base
All technical data stated in this Product Data Sheet are based on laboratory tests.
Actual measured data may vary due to circumstances beyond our control.
For information and advice on the safe handling, storage and disposal of chemical
products, users shall refer to the most recent Material Safety Data Sheet containing
physical, ecological, toxicological and other safety-related data.
Legal Notes
Sikafloor-220 W Conductive
5/7
CE Labelling
The harmonized European Standard EN 13 813 Screed material and floor screeds
- Screed materials - Properties and requirements specifies requirements for screed
materials for use in floor construction internally.
Structural screeds or coatings, i.e. those that contribute to the load bearing capacity
of the structure, are excluded from this standard.
Resin floor systems as well as cementitious screeds fall under this specification.
They have to be CE-labelled as per Annex ZA. 3, Table ZA.1.5 and 3.3 and fulfil the
requirements of the given mandate of the Construction Products Directive (89/106):
1)
EN 13813 SR-B1,5
Primer/sealer
(systems as per Product Data Sheet)
Reaction to fire:
Efl
SR
Water permeability:
NPD2)
Abrasion Resistance:
NPD
Bond strength:
B 1,5
Impact Resistance:
NPD
Sound insulation:
NPD
Sound absorption:
NPD
Thermal resistance:
NPD
Chemical resistance:
NPD
1)
Last two digits of the year in which the marking was affixed.
2)
No performance determined.
3)
Sikafloor-220 W Conductive
6/7
CE Labelling
The harmonized European Standard EN 1504-2 Products and systems for the
protection and repair of concrete structures Definitions, requirements, quality
control and evaluation of conformity Part 2 : Surface protection systems for
concrete gives specifications for products and systems used as methods for the
various principles presented under EN 1504-9.
Products which fall under this specification have to be CE-labelled as per Annex
ZA. 1, Tables ZA.1a to ZA 1g according to the scope and relevant clauses there
indicated, and fulfil the requirements of the given mandate of the Construction
Products Directive (89/106):
Here below indicated are the minimum performance requirements set by the
standard. For the specific performance results of the product to the particular
tests, please see the actual values above in the PDS.
Construction
0921
Sika Deutschland GmbH
Kornwestheimerstrae 103-107
D - 70439 Stuttgart
1)
08
0921CPD2017
EN 1504-2
Surface Protection Product
Coating
2)
< 3000 mg
Permeability to CO2:
SD > 50 m
EU Regulation 2004/42
VOC - Decopaint
Directive
3)
Class I
Impact resistance:
Class I
2.0 N/mm
Fire Classification: 4)
Efl
1)
Last two digits of the year in which the marking was affixed.
2)
Tested as a part of a system build-up with Sikafloor -156, Sikafloor -161 and
Sikafloor-262 AS N.
3)
4)
The maximum allowed VOC content acc. to the EU-Directive 2004/42 (Product
category IIA / j type wb) (Limits 2010) in the ready to use product is 140 g/l.
The maximum VOC content of Sikafloor-220 W for the ready to use product is <
140 g/l.
USGBC
LEED Rating
Phone: +606-7991762
Fax:
+606-7991980
e-mail: info@my.sika.com
www.sika.com.my
Sikafloor-220 W Conductive
7/7