Professional Documents
Culture Documents
: M. Kashah Nasthy
NIM
: 0904102010007
1. 3D Solid Object
Material
Boundary condition
Loading
Answer
1. Deformed shape
Definition
Type
Total Deformation
By
Time
Display Time
Last
Yes
Identifier
Suppressed
No
Results
Minimum
0. mm
1.9463e+005 MPa
Maximum
9.8879e+005 mm
4.1346e+008 MPa
3. Maximum load
Dari tabel dapat dilihat nilai deformasi minimum maksimum dan tegangan
Von-mises minimum dan maksimum.
Deformasi minimum
: 0 mm
: 194.630 MPa
Tegangan maksimum
: 413.460.000 MPa
2. 3D Solid Analysis
The steel cylinder has an inner radius of 5 inches and an outer radius of 11 inches with an
internal pressure. Find a stress in a thick open-ended cylinder.
Answer
Maksimum deformasi
secara teoretikal:
SX = -1000 psi and SZ = 1520,8 psi
Dari hasil simulasi didapat nilai SX = -1005,51 psi dan SZ = 1528,8 psi. kalkulasi
ANSYS terlihat menyerupai dengan hasil teoretik.
Nodal Solution
Dari tabel:
SX = -997,88 dengan 0,22% berbeda dari harga sebenarnya 1000, dan SZ = 1521,5
dengan 0,04% berbeda dari harga sebenarnya 1520,8.
Geometry
: The thickness of the bracket is 3.125 mm.
Material
: Steel with modulus of elasticity E= 200 GPa
Boundary condition
: The bracket is fixed at its left edge.
Loading
: The bracket is loaded uniformly along its top
surface. The load is 2625 N/meter.
Objective
: 1. Plot deformed shape
2. Determine the principal stress and the von
Mises stress
3. Remodel the bracket without the fillet at the
corner, and see how the principal stress and von
Mises stress change
Answer
1. Plot deformed shape
Tabel Report
Dari tabel report dapat dilihat nilai minimum dan maksimum dari total deformasi, stress
von Mises, dan principal stress.
Arah deformasi dapat dilihat pada gambar plot deformed shape. Dari gambar, permukaan
atas bracket mengalami melar (creep) akibat load yang diberikan. Maksimum deformasi
sebesar 402,42 mm.
Principal stress
Nilai maksimum principal stress dari kedua model memiliki perbedaan begitu juga
dengan nilai yang diperoleh dari von Mises.
Von Mises Stress
Dari nilai yang diperoleh dapat dilihat bahwa tegangan yang pada bracket tanpa
fillet lebih besar dibandingkan tegangan pada bracket dengan fillet.
4. Thermal
Electronic circuit is made of copper with thermal conductivity of 386 W/m K. Also
it generates heat at the rate of 10e6 W.
The enclosing container is made of steel with thermal conductivity of 20 W/m K.
The fins are made of aluminium with thermal conductivity if 180 W/m K.
Boundary conditions : there is convection along all the boundaries except the
2
bottom, which is insulated. The film coefficient is 50 W/ m
K and th Bulk
Temperature is 20 C.
Objective
:
1. To determine the nodal temperature distributin.
2. To determine the maximum value of temperature in the component.
Answer
Dari tabel dapat dilihat nilai maksimum temperature terletak pada node 28500 sebesar
25798 C.
Minimum temperature is
: 399,414 C
Maximum temperature is
: 25797,9 C
5. Fluid
Answer
Plot velocity profile in the channel
Kesimpulan yang dapat di ambil dari hasil simulasi adalah nilai tegangan maksimum
yang di terima channel akibat kecepatan fluida yang diberikan senilai 0,1 m/s adalah
131685 MPa.
Plot velocity profile across the elbow.
Distribusi kecepatan antara garis yang terhubung oleh 2 point dapat di lihat dalam bentuk
grafik sebagai berikut.
2 titik hitam terlihat pada gambar merupakan path yang yang akan dioperasikan ke dalam
bentuk grafik.