You are on page 1of 16

PAPER-II

FEB 2000

[WORKSHOP TECHNOLOGY]
1.

Spur gear circular pitch meansa) distance from centre of one thread to the centre of next consecutive tooth measured on the pitch circle
b) imagining line passing through the points at which the teeth of meshing gear contacts
c) both (a) & (b) are correct
d) none of the above is correct

2.

Diametrical pitch of spur gear:


a) represents the no. of teeth/inch
b) diameter of the pitch circle
c) both (a) & (b) are correct
d) none of the above

3.

If drill size is not written on the body of the drill then it can be obtained by:
a) drill sharpening gage
b) it will be written on right-hand side of the drill shank
c) it will be written on left-hand side of the drill shank
d) none of the above is correct

4.

In cross peen and straight peen hammer the peen end is:
a) parallel and perpendicular to the handle
b) perpendicular and parallel to the handle
c) both parallel to the handle
d) both perpendicular to the handl
5. No. of thread/inch is measured by:
a) screw pitch gage
b) ring gage
c) plug gage
d) all are correct

6.

Metric micrometer graduation on steeve


a) 0.025
b) 0.001
c) 0.05
d) 0.50

7.

Buttress thread is used:


a) where a thread requiring greater strength in one direction
b) where a thread requiring greater strength in both directions
c) it is used for feed and lead screw on machine tools
d) none is correct
[ELECTRICITY]

8.

Inductive reactance is measured in:


a)
henry
b)
farad
c)
ohm
d)
none

9.

Overheating a circuit from excessive amount of current is protected by:


a)
fuse
b)
circuit breaker
c)
thermal protector
d)
all are correct

10.

Battery cell voltage and current high in:


a)
series connection
b)
series-parallel connection
c)
parallel connection
d)
all are wrong

11.

Generator voltage depends on:


a)
strength of magnetic field
b)
speed of rotation of conductor
c)
no. of turns of conductor
d)
only (a) & (b) are correct

12.

State of charge of Ni-Cd battery will be determined by:


a)
measuring specific gravity of the electrolyte
b)
by a measured discharge
c)
by the temperature of the plates
d)
by the level of the electrolytes
[ELECTRONICS]

13.

NPN transistor used as amplifier when:


a)
current flows from emitter to base
b)
current flows from base to emitter
c)
current flows from base to collector
d)
current flows from collector to base

14.

Advantage of tetrodes over triodes


a) greater amplification for smaller input voltage
b) less feedback from plate to the grid circuit
c) both (a) & (b) are correct
d) only (a) is correct

15.

Figure shows:
a) NOR gate
b) OR gate
c) Exclusive OR gate
d) None

14.

In gate if a=0 and b=0 then c=1, and a=0 and b=1 then c=1, the gate is:
a)
NAND gate
b)
AND gate
c)
NOR gate
d)
OR gate

15.

Convert number 36 to binary number


a)
100100
b)
110010
c)
100111
d)
11100
[HARDWARE]

16.

Figure shows:
a)
reworked bolt
b)
stretched steel bolt
c)
close tolerance bolt
d)
Al-alloy bolt

17.

Self plugging (friction lock) rivets are replaced by:


a)
with the same size of solid rivet
b)
with the rivet one size larger
c)
can not be replaced by any one
d)
all are incorrect

18.

Alloy steel lock bolts may be used to replace:


a)
hi-shear rivet
b)
solid steel rivet
c)
all bolts of same dia and head type
d)
all are correct

19.

Fluid lines are identified by:


a) colour codes and words
b) colour codes and geometrical symbols
c) both (a) and (b) are correct
d) only (b) is correct

20.

Ring packing slight surface flows may be detected by:


a) using 4-power magnifying glass with adequate lighting.
b) By rolling the ring as inspection cane or dowel, the inner dia surface can also be checked for small cracks.
c) Slight scratching of the ring when it is rolled inside out will help to reveal some defects not otherwise visible
d) All are correct
[GENERAL MAINTENANCE]

21.

Which is correct concerning jacking of an aircraft:


a)
tripod jack of appropriate size for the aircraft being jacked should be replaced under the aircraft jacking points
and perfectly centered to prevent them from cocking when the aircraft is raised.
b)
At least three places or points are provided on aircraft for jacking purposes, sometimes fourth place is given to
stablise the aircraft while it is being jacked at the other three points.
c)
All are incorrect
d)
Both (a) and (b) are correct

1.

Which is correct concerning mooring of an aircraft:


a)
small aircraft should be tie down after each flight to preclude damage from sudden storms.
b)
Normal tie down procedure for heavy aircraft can be accomplished with rope or cable tie down
c)
Both (a) and (b) are correct
d)
All are incorrect

2.

ATA 24 is:
a) communication
b) equipment/furnishing
c) electrical power
d) auto flight

3.

In ATA code wires and cables designation given:


a) side by side
b) in suffix and prefix
c) .
d)
[BASIC ENGINE]
Purpose of additives in fuel is:
a) to prevent microbial growth
b) for water detection
c) for detonation
d) all are correct

4.

5.

In four stroke engine ignition takes place in each cylinder after:


a) two complete revolution of crankshaft
b) after 180 movement of crankshaft
c) after only half rotation of crankshaft
d) after four rotations of crankshaft
[INSTRUMENT]

6.

Manifold pr gage shows the pr when it is not open:


a) atmospheric pr
b) manifold pr
[METALLURGY]

7.

Rockwell hardness tester measures the


a) resistance to penetration
b) dia of penetration
c) both (a) & (b) are correct
d) none of the above is correct

8.

Titanium can be identified by:


a) spark test
b) moistening the titanium and using it to draw a line on a piece of glass
c) it will give a dark line similar in appearance to a pencil mark
d) all are correct

9.

In annealing the slow cooling will do:


a) soften the steel
b) increase the toughness of steel
c) give greater strength of steel
d) all are correct

10. If the soaking period of heat treated parts increases then:


a) the part will start to reprecepctate
b) grain structure will be finer
c) both (a) & (b) are correct
d) all are incorrect
11. Barcol tester is applicable for:
a) Al-alloys and Copper, Brass
b) Al-alloys, Mg-alloys and Copper
c) Mg-alloy and Copper
d) All are correct
12. Corrosion of Titanium is cleaned by:
a) hand polish with Al-polish and mild abrassive paper
b) using a stiff and hog bristle brush
c) use of small power buffers and buffing compound
d) hand wire brush and steel wool
13. T36 means:
a) alloy has been solution heat treated and has had its thickness reduced by 6% by cold working
b) artificially aged only
c) solution heat treated followed by strain hardening
d) solution heat treated followed by artificially aged only

14. In soldering the flux is used:


a) to remove and prevent oxidation the metal
b) allowing the solder to flow evenly
c) both (a) & (b) are correct
d) (a) & (b) are correct and to unit more firmly with the surface to be joined
15. In welding the welded parts are heat treated:
a) to provide greater strength in welded region
b) to relieve the stress set up during welding
c) to make soften the welded parts
d) all are incorrect
16. In overlap weld joint:
a) flux used between the two parts
b) flux is used on upper parts
c) flux is used on the inner parts
d) all are incorrect
(not exactly, but like that)
17. In welding copper and brass the flame is used:
a) slightly carbonized
b) neutral flame used
c) oxidized flame used
d) both (a) and (b) are correct
18. In welding Al-alloy the flux used is:
a) potassium chloride
b) potassium fluoride
c) potassium bisulphate
d) all are incorrect
19. In radio graphic inspection method:
a) thicker the material, darker the impression
b) thinner the material, darker the impression
c) thicker the material, lighter the impression
d) thinner the material, lighter the impression
20. In dypenetrant inspection method the long or short crack will:
a) take longer time to be penetrate
b) will take less to be penetrate
21. In fluorescent penetrant inspection the defect will appear:
a) in green colour as seen in black light
b) will appear in deep blue-violet colour
c) bright red indication will appear
d) in ultraviolet colour
22. Defect in dye penetrant will be appear:
a) brilliant yellow green colour
b) bright red colour
c) deep blue violet colour
d) all are incorrect
23. Defects in the inner surface will be seen by:
a) Boroscopes method
b) Fiberooptics scope method
c) Indoscope method
d) All are correct

24. Factor include in radiographic exposure


a) material thickness and density
b) type of defect to be inspected
c) type of X-ray machine used and (a) and (b) are correct
d) only (a) and (b) are correct
25. Which are used as a filler material:
a) boron
b) cellulosic material
c) polyester resin
d) epoxy resin
26. Matrix material
a) it is a bonding material
b) it transfers the stress on composites to the reinforcing fiber
c) used as a adhesive
d) all are correct

PAPER-2 JUNE 2000


1.

In 7075-0 indicates
a) annealed
b) strain hardened
c) solution HT
d) none

2.

One r is dash on bolt head indicates


a) CRS bolt
b) NAS close tolerance bolt
c) AN standard bolt
d) None

3.

The line used for reference of pars is


a) reference line
b) hidden line
c) phantom line
d) black line

4.

The colour of 6053 Al-alloy is


a) red
b) black
c) grey
d) white

5.

Lock bolt, which indicates flat head is


a) ALPP
b) ALPB
c) ACST
d) ALSF

6.

In flexible hoses slack is given


a) 2 to 3% of total length
b) 5 to 8 % of total length
c) 3 to 9% of total length
d) 10% of total length

7.

When tightening of nut is precious, which tool is used


a) allen wrench
b) torque wrench
c) spanner wrench
d) combination wrench

8.

Which AL-alloy rivet has highest strength


a) 5056-T
b) 2117-T
c) 2024-T
d) 5056-W

9.

Al-alloy is not heat treated properly to have uniform grain boundaries it has
a) stress corrosion
b) galvanic corrosion
c) intergranular corrosion
d) fretting corrosion

10.

Which one is unpaired


a) battery accumulator
b) diode NRV
c) AC generator vortex generator
d) EMF MMF
7

11.

Which is used to transfer rivet size from template to new sheet is


a) centre punch
b) pin punch
c) alignment punch
d) transfer punch

12.

A side clearance between piston ring and cylinder wall is measured by


a) telescopic gauge
b) thickness gauge
c) micrometer
d) plug gauge

13.

When base circuit is open at R, then


a) bulb can not be turned off
b) bulb can be turned off
c) bulb can not be effected
d) high current will flow in circuit
The resistance of conductor depends on
a) temperature
b) length and material
c) cross-sectional area
d) all

14.

15.

16.

In on inductive circuit
a) current lags behind voltage by 90
b) current leads behind voltage by 90
c) Current and voltage are in phase
d) None
In magnetic particle inspection, nickel plating does not give indication of
a) crack
b) discontinuities
c) corrosion
d) none

17.

In dye penetrant inspection, the defects under while light appers


a) black
b) green
c) red
d) all

18.

Which is unpaired
a) dye penetrant capillary acceptance
b) ultrasonic test peizo electricity
c) eddy current test current acceptance
d) magnetic test skin test

19.

Dye penetrant inspection is applicable to


a) ferrous alloys only
b) plastic and non metal
c) non ferrous alloys metal
d) all

20.

In ultrasonic test, when mechanical stress vibration is applied to crystal quartz then these are
a) electrical energy and voltage are produced
b) more vibrations are produced
c) as in (A) and varies with the thickness of crystal
d) none

21.

Form of corrosion which occurs between metal and non metal is


a) filliform corrosion
b) crevice corrosion
c) exfoliation corrosion
d) fretting corrosion

22.

Normalizing is applicable to
a) cu-alloys
b) Al-alloys
c) Ferrous alloy only
d) Both a & b

23.

Main content of 5056 Al-alloys is


a) Zn
b) Mg
c) Cu
d) Si

24.

Freating the parts in anhydrour ammonia is


a) carburizing
b) nitriding
c) cyaniding
d) normalizing

25.

For maximum elongation, ductility, tensile strength and impact resistance Mg-alloy is
a) solution heat treatment
b) casted
c) precipitation heat treatment
d) none

26.

Which one is not primary cell


a) Zn-carbon cell
b) Lead acid cell
c) Alkaline cell

27.

Ni-cd battery is charged with


a) constant current varying voltage
b) constant voltage varying current
c) both (a) & (b)
d) none

28.

An ac circuit consists of inductance of 10, capacitance 4 & resistance 8 the impedance of the circuit is Z=R+(XLXC)
a) 6
b) 10
c) 5.5
d) 8

29.

Glider has lift due to


a) high aspect ratio (s/c)
b) high lift/co-efficient of lift (L/C) ratio
c) symmetrical wing
d) more wing area

30.

In flight extending flaps


a) increase lift
b) increase lift and drag both
c) increase drag
d) reduce stalling speed
9

31.

Which has increasing order of strength?


a) 2S, A14ST, 17ST, 24ST
b) 2S, 24ST, 17ST, A17ST
c) 2S, 17ST, 24ST
d) 2S, A17ST, 24ST, 17ST

32.

Composite has
a) resistance to wear
b) high strength to weight ratio
c) resistance to corrosion
d) all

33.

The static vents with the flat surface plate at two position to
a) minimize position error
b) have is formation freedom
c) both a & b
d) none

34.

Heat treated defect in metal is detected by


a) ultrasonic test
b) eddy current testing
c) dye penetrate testing
d) radiography testing

35.

An ac circuit has inductance 3 and resistance of 4, and then impedance of the circuit is
a) 3
b) 1
c) 5
d) 7

36.

The maximum radius for bending of Al-alloy should be


a) 3 times the sheet thickness
b) 6 times the sheet thickness
c) 9 x sheet thickness
d) 10 x sheet thickness

37.

The truth table is for


A
0
0
1
1

38.

39.

B
0
1
0
1

Y
0
1
1
0

A)
OR-gate
B)
X OR gate
C)
AND-gate
D)
NAND gate
Beryllium copper has greater advantage of
a) creep
b) high strength and uniform properties
c) corrosion resistance
d) uniform grain structure
Mg is ________
a) Susceptible to corrosion
b) Has tendency to crack
c) Resistance to corrosion
d) Both a & b

10

40.

For most metals, which oxy-acetylene flame is used?


a) neutral flame
b) oxidizing flame
c) carburizing flame
d) none

41.

Which one is heat treatable alloy?


a) 24 S
b) clad 24 S
c) A17S
d) Any Al-cu alloy

42.

Rack is mist with a gear, it is used to change (the purpose of rack and pinion is to changa)
a) rotary motion to reciprocating motion
b) reciprocating motion to rotary motion
c) both a & b
d) none

43.

Lift depends upon


a) velocity of relative wind
b) density of air
c) wing span (area)
d) all

44.

Metal matrix composite is a recent convectional material in which


a) resin is reinforced with metal
b) resin and fibers are reinforced with metal
c) fibers are reinforced with metal during molten stage
d) all are correct

45.

In SAE-1030, carbon percentage is


a)
30%
b)
9.5%
c)
10 %
d)
30%

46.

To roll a pure Al-sheet over Al-alloy is called


a) Al-clad
b) Pure clad
c) Laminated Al
d) Both a & b

47.

Magnetic particle inspection (MAP) can be done when flow is


a) at or near the surface
b) on or in depth of surface
c) near or in depth of surface
d) all

48.

Cd-plating is done on steel parts


a) to prevent corrosion
b) to built up
c) to give texture and brightness
d) all are correct

49.

Heated-treated and non-heat treated metal 25, distinguished by


a) magnetic particle inspection
b) eddy current test
c) dye penetrate inspection
11

d) ultrasonic test
50.

Titanium is heat treated by


a) normalizing
b) full annealing
c) case hardening
d) all

51.

Maximum bending in case of copper tubing is


a) three times to internal diameter
b) six times to internal diameter
c) nine times to internal diameter
d) twelve times to internal diameter

52.

Pickling of steel is carried out in


a) H2SO4
b) Muriatic acid
c) all
d) none

53.

Peizo -electric effect is


a) if mechanical stresses applied to a quartz crystal, then voltage is induced
b) frequency depends on thickness
c) both a & b

54.

Electroplating provides
a) corrosion resistant surface
b) wear resistant surface
c) both a & b
d) none

55.

Re-heating is done to
a) remove strain and stresses
b) remove effect of heat treatment
c) remove hardness and brittleness
d) none

56.

In cable strand, the wires are performed to provide


a) corrosion resistance
b) flexibility
c) prevents from raveling
d) both a & b

12

PAPER-2

OCT 2000

1.

The piston engine works on


a) Boyles law
b) Brayton cycle
c) Charles law & otto cycle
d) Both a & c

2.

The mechanical efficiency of piston engine is determined by


a) engine speed
b) fuel used
c) mean effective pressure
d) mixture ratio (throttle setting)

3.

The main alloying element is 7075 Al-alloy is


a) Cu
b) b) Mn
c) c) Zn
d) d) Si

4.

The tubes are sized by


a) inside diameter in increment of 1/16
b) inside diameter in increment of 1/32
c) out side diameter in increment of 1/16
d) out side diameter in increment of 1/32

5.

Flared tube fittings used in a/c are made of


a) Al-alloy
b) Cu
c) Steel
d) All are correct

6.

Muntz metal consists of


a) 60% of Cu and 40% of Zn
b) 60% of Zn and 40% of Cu
c) as in (a) and basically brass
d) as in (b) and basically brass

7.

Steel has fine grain structure, when


a) when heated above the critical temperature
b) when heated below the critical temperature
c) .
d)

8.

The soldering of Al-alloys differs from other metals due to


a) high heat expansion and contraction
b) greater heat input
c) uneven expansion and contraction
d) all

9.

Kirchoffs law is applicable is


a)
d.c
b)
a.c.
c)
d.c. circuit having resistance
d)
ac & dc

13

10.

In modulation, the available band is


a) one
b) two
c) no band
d) many band

11.

The modulation in which, amplitude is kept constant and frequency is changed is called
a) amplitude modulation
b) space modulation
c) frequency modulation
d) phase modulation

12.

The angle of attack is the


a) acute angle between aircraft longitudinal axis and chord line to which aerofoil is mounted on the aircraft
b) horizontal acute angle between the symmetry aircraft and wind direction from which it touches the aircraft
c) the acute angle between the summetry of the aircraft and the chord line of aerofoil section
d) all are correct

13.

In NDT of material by Dye penetrant inspection (DPI) the volume of defect is interpreted by
a) Staining rate
b) Staining speed
c) Staining extent
d) All

14.

In UST, scanning is carried out by moving both probes simultaneously in opposite direction for
a) flash butt joint (weld)
b) heavy forgings
c) heat treatment defect
d) thickness measurement

15.

During fuelling, the most necessary precaution to be observed


a) grounding connection first made to aircraft and then fuelling vehicle
b) grounding connection first made to fuelling vehicle and then the aircraft
c) skillness of fuelling person
d) all are correct

16.

The fluid use for all types of aircraft engines except rocket is
a) gasoline
b) air
c) ATF
d) All are correct

17.

In composites, the strength is provided by


a) reinforced fibre
b) core
c) resin
d) (a) and fibre

18.

In hardness testing of composite, the hardness is measured


a) resin
b) reinforcing fibre
c) specific chart
d) both a & c are correct

19.

In composites, repair the part is steeped rather than to be scrafed for


a) uniform shear stress
b) uniform tensile stress
c) smoothness
d) both a & b

14

20.

After honeycomb repair, the moisture entrapment is inspected by


a) radiography
b) ammeter
c) laser holography
d) all

21.

In uniform fluid flow, the fluid is first made to flow through a tube and the pressure exerted by the fluid is measured by
a) dynamic pressure
b) static pressure
c) reynolds no.
d) all

22.

PARKETON is used for protection of


a) steel
b) numinium
c) Mg
d) As in (a) and cable

23.

The rust and corrosion is removed from highly stressed steel parts by
a) abrasive paper
b) fine buffling cloth on buffling wheel
c) wire brush
d) all

24.

Centre drill is used to produce


a) short hole and CSK hole (countersunk)
b) short hole and large hole
c) both a & b
d) none

25.

During repair procedure of composite part treatment is done for


a) small disbands
b) restore surface protection
c) seal honeycomb casting
d) none

26.

Synthetic rubber used in the aircraft is designated GRM as


a) poly sulphide polymer
b) isobutylene
c) complex of butylenes and cresylonitrile
d) government rubber mono-vinyl acetylene or neoprene

27.

The neutralize the surface of Ni-cad battery compartment


a) Boric acid
b) Water
c) Backing soda
d) All

28.

Close tolerance bolt is identified by


a) triangle marking on head
b) crossed triangle marking on head
c) circle marking on head
d) triangle on head with plus marking within it

29.

While jacking, the approved procedure is


a) both wheels are raised together
b) wheels are raised one after another
c)
d)
15

30.

The class of fit required for a tight drive fit is


a) class-1
b) class-2
c) class-3
d) class-4

31.

Piston engines mechanical efficiency differs due to


a) difference of pressure
b) difference of temperature
c) difference of grade of fuel used
d) difference in mass of fuel

32.

A device which gives lateral control and is mounted at the opposite surface of wing
a) spoiler
b) vertex generator
c) tab
d) flap

33.

The presence of water can be detected by


a) USI
b) DPI
c) Endoscope
d) Radiography

34.

Aircraft bolts are generally manufactured with a


a) Class 1 fit for the threads
b) Class 2 fit for the threads
c) Class 3 fit for the threads
d) Class 4 fit for the threads

35.

The nose of l00LL AVGAS dispenser is


a) red
b) blue
c) black
d) green

36.

Which is low energy logic circuit


a) TTL
b) ECL
c) Both a & b
d) None

16

You might also like