Professional Documents
Culture Documents
The casing slips are designed and manufactured in API Spec 7K and SY5049
Slips for Well Drilling. It is manufactured in a structure of multi -segment pieces
with firm structure, light weight and large holding range, which is easy to fit the
changing of the external diameter of the casing pipes due to wear and tear.
Main technical parameters:
Casing OD
in
4.1/2-5
5.1/2-6
6.5/8
7.5/8
8.5/8
9.5/8*
10.3/4*
mm
114.3127
139.7152.4
168.3
177.8
193.7
219.1
244.5
273.1
2628-108
2620-108
2628-144
2619-144
2630-144
2630-156
2630-168
2630-180
13
14
15
181
(82)
192
(87)
209
(95)
9
168
(76)
Weight lb (kg)
12
157
(71)
196
(89)
184
(83.5)
166
(75)
14.3/8
16.1/4
250(2250)
in
11.3/4*
13.3/8*
16*
18.5/8*
20*
24*
26*
30*
mm
298.5
339.7
406.4
473.1
508
609.6
660.4
762
2627-204
2630-216
2631-252
2626-300
2631-312
2631-360
2631-396
2631-444
17
18
21
25
26
30
33
37
Weight lb (kg)
260
(118)
258
(117)
308
(140)
367
(166.5)
383
(174)
443
(201)
486
(221)
(247.5)
30
32
36
Casing OD
19
250(2250)
21.3/4
26
125(1125)
546
UC-3
Type UC-3 Casing slips Main technical parameters:
Type
Casing OD
Circular
Buttons
Total
number of
segments
Handle
Fit bushing
8.5/8 UC-3
7
7.5/8
8.1/8
10.3/4 UC-3
8.5/8
9.5/8
10.3/4
11.3/4~24 UC-3
11.3/4
12.3/4
13.3/8
18.5/8
20
24
10
10
12
17
19
10
10
12
17
19
Fit 4 taper
Fit 3 taper
:
a.;
b.;
c.;
d.
1)It is necessary to measure the actual external diameter of the casing to see
whether it is in the holding range of the casing slips before using.
2
2)Whether the hinge pin is rotated smoothly and whether there is any blocks
or not should be checked before operation.
3)Knocking the handle and the back cone of the slips with big hammer is
strictly forbidden, and be sure do not drop the slips from higher position to avoid
any damage to the handle and cone surface.
4)The surface of the casing slips should be kept clean by daily cleaning and
the rotary part and back cone should be coated with lubrication oil against rusty.
5)Periodic inspection should be done for the casing slips:
a)Check whether the fixing bolt of the casing slip inserts are
loosed or not in order to avoid the slip inserts dropping to the well.
b)Check whether the casing slip inserts brunt or not.
c)Checking with ruler to see whether the back cone of the casing slips is worn
or not.
d)Checking the hinge pin's condition of the casing slips, to see whether it is
worn or not.
6)The casing slip inserts should be replaced entirely in time once found it is
worn out. Be careful do not use the old inserts with the new one at the same time in
order to avoid damages to the slips body due to concentrated load.
7)Remove the harden granules away from the slips cone surface to reduce the
weariness on the cone surface.
8)Often check the wear condition of the casing slips cone surface in order to
avoid dropping into the well.
9)When the casing slips are not in use for a long time, the slips should be
cleaned and coated with anti-rustic oil and placed in a dry place with good
ventilation.
10)The back cone can not be repaired for further using once it is seriously
worn out. This factory is not responsible for any accident caused by the fact that
the slips holding quality is affected by the self-repairing of the old back cone.