Professional Documents
Culture Documents
3) Details drawing
4) What is the class of working drawing that is the description of a single parts (June 2010
session)
1)illustrated drawing
2) Assembly drawing
3) Details drawing
4) None of Above
5) Zone number of aircraft blue prints are used to (June 2010 session)
1) Locate parts, sections & views on Large drawings
2) Indicates different section of aircraft
3) to locate parts in aircraft
6) Drawing used in IPC is a (June 2010 session)
1) Exploded view drawing
2) Block diagram
3) Details drawing
7) In ATA 100 specification, the codes for hydraulic, pneumatic five protection system &
engine indicating system are: (Feb 2008)
1) 29, 26, 39, 77
2) 29, 36, 26, 77
3) 36, 26, 29, 79
4) 29,
71, 36, 27
8) In case of an isometric drawing (OCT07)
1) vertical lines are at an angle of 1200
2) vertical lines are vertical & horizontal lines at 300
3) vertical lines are vertical & horizontal lines at 60 0
9) Front, top and right side view correspond to (OCT07)
1) orthographic projection
2) isometric drawing
3)perspective drawing
10) In ATA 100 specification, the codes for hydraulic, pneumatic, fire protection system
and engine indicating systems are: (FEB07)
1) 29, 26, 39, 77
2) 29, 36, 26, 77
3) 36, 26, 29, 79
4) 29,
71, 36, 27
11) Mark the correct statement(FEB07)
1) ATA 22 represents communications
3) ATA 34 represents lights
12)
As per ATA code, hydraulic fluid, pneumatic, fire & engine indicating is (OCT-06)
1) 29, 26 , 36, 77
2) 77, 29, 36, 29
3) 29, 36, 26, 77
13) Schematic diagram indicates(OCT-06)
1) does indicate individual components
2) used in trouble shooting
3) aid in installed position
14) Fig shows(JUNE-06)
1) hidden line
2) visible outlines
3) centre line
4) none
15) Identify the drawing symbols given below (JUNE-06)
1) automatic reset, push reset, push reset, pull off
2) automatic C.B., push CB, push pull C.B.
3) normal C.B., pull-pull C.B., push C.B.
4) none
16) In TA-100 systems, 27 represents: (JUNE-06)
1) fire protection
2)flight control
3) pneumatic system
17) Which ATA code indicate hydraulic power, Fire protection, pneumatic engine(OCT05)
1) 29, 26, 36, 77 2) 25, 26, 36, 77
3)29, 28, 36, 77
18) Which view is used to show the location of object at an angle to plane: JUNE 2005 &
Feb 2005
1) sectional view 2)plan view 3)elevation 4)auxiliary view
19) Working drawing is a drawing Feb(2004)
1) given rough idea about the component, system drawn
2) it includes assembly drawing
3) as in 2 & includes installation drawing
4) all of the above
20) Mark the correct statement Feb(2004)
1) leader line is used to put the dimension over
2) phantom lines used to indicate the portion of part not shown on drawing
3) break-in line indicates the alternative position of part
4) none
21) Tolerance means Feb(2004)
1) positive allowance + negative allowance
3) Negative allowance
2)positive allowance
4) None
4)black line
3)electrical power
4)
34) The ATA-100 specification no. for hydraulic, pneumatic, stabilizers and engine is(OCT1999)
1) 55,36,29,77
2)36,29,55,77
3)29,36,55,77
4)
29,36,77,55
4)all