Professional Documents
Culture Documents
North American
Product Technical
Guide
Volume 1:
Direct Fastening
Technical Guide
A guide to specification
and installation
*ISO 14001 US Only
2013 Edition
Table of Contents
Introduction
1.0
2.0
3.0
16
Reference
4.0
172
Hilti North American Product Technical Guide Volumes 2 and 3 are also available.
Download them from www.us.hilti.com or contact your Hilti Field Engineer about them today.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 1
Description
1.0
2.0
2.1
2.2
2.3
2.4
3.0
3.1
3.1.1
3.1.2
3.1.3
3.2
3.2.1
3.2.1.1
3.2.1.2
3.2.1.3
3.2.1.4
3.2.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Direct Fastening Technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Base Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Evaluation of Test Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Seismic Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Direct Fastening Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Direct Fastening Terminology and Applications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Direct Fastening Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Benefits of Direct Fastening Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Common Direct Fastening Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
General Construction Fastening Systems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
General Construction Fastener Design and Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Fastening to Concrete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Fastening to Steel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Powder-Actuated Cartridge Selection Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Power-Actuated Fastener and Tool Selection Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
General Application Fasteners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
3.2.3
3.2.4
3.2.5
3.2.6
3.2.7
3.2.8
3.2.9
3.2.10
3.2.11
3.2.12
3.3
3.3.1
3.3.2
3.3.3
3.3.4
Page
X-U, X-U 15, DS, EDS, X-C, X-S13, X-GN, X-EGN and X-GHP fastener series
for general applications to concrete, steel or masonry
X-U, X-U 15, DS and EDS fasteners for attachment of perimeter track
and deflection slip clips to concrete or steel
X-GPN 37 MX fastener for attachment of structural wood panels to cold-formed steel members
X-U 15, X-S13, X-S16, X-GN, X-EGN and X-GHP fastener series
for attachment of drywall track to concrete, steel or masonry
X-CF 72 and X-CP 72 fasteners for attachment of wood sill plates to concrete
Carbon steel (1/4" and 3/8") powder-actuated threaded studs for attachment to concrete
Carbon steel (1/4", 3/8" and 8mm) and stainless steel (1/4", 3/8" and 8mm) powder-actuated
threaded studs for attachment to steel
Innovative X-BT (1/4", 3/8" and 8mm) blunt-tip threaded stud fastener for attachment
to coated or painted and full thick steel
Threaded and smooth rod hangers (X-HS and X-RH), cable holders, clamps and tie fasteners
(X-ECH, X-EKB MX, and X-ECT) and conduit clips (X-BX, X-EMTC and X-EMTSC MX)
for use in mechanical and electrical applications
X-IE and X-SW fasteners for attachment of insulation and other soft materials
to concrete, masonry or steel
X-CC Ceiling Clip assemblies with or without pre-tied wires for attachment of suspended ceiling systems
Eye Lag Screws for attachment of suspended ceiling systems to cold-formed steel or wood base materials
2 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Description
3.4
3.4.1
3.4.2
3.4.3
3.5
3.5.1
3.5.1.1
3.5.1.2
3.5.1.3
3.5.1.4
3.5.1.5
3.5.1.6
3.5.1.7
3.5.1.8
3.5.1.9
3.5.2
3.5.3
3.5.4
3.5.5
3.5.6
3.6
3.6.1
3.6.1.1
3.6.1.2
3.6.1.3
3.6.1.4
3.6.1.5
3.6.1.6
3.6.1.7
3.6.2
3.6.3
3.6.4
3.6.5
4.0
4.1
4.2
4.3
Page
Removable and reusable grating (X-FCM) and checkerplate (X-FCP) fastening systems available
in HDG (Duplex Coating) and stainless steel corrosion resistance and consisting of a disk that threads
onto a powder-actuated threaded stud. Stainless steel version specifically designed for off-shore applications
X-GR RU and X-MGR grating fastening systems with HDG equivalent corrosion resistance for attachment
of grating in on-shore industrial applications
S-SLC 01 and S-SLC 02 sidelap connectors and Hilti No. 10 HWH screws
for many types and gauges of steel deck
Mechanically attached X-HVB shear connector for use in composite beam construction
with steel beams and concrete slabs
Screws specifically designed for HVAC applications, including the innovative Zip Screws
with HyperThread technology
Self-drilling screws specifically designed to resist HASCC that can be caused by stress,
dissimilar metals and moisture, available in HWH head style and diameters #10 through 5/16"
Stainless steel screws with carbon steel drill points providing the drilling capacity of a standard self-drilling
screw with the corrosion resistance of a 300 series stainless steel fastener specially designed to resist
the effects of HASCC
Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
Approvals and Listings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
Reference Standards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
Technical References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 3
1.0 Introduction
1.1 About Published Load Values
The Direct Fastening Technical Guide is intended to supplement the Hilti Product Catalog with technical information for
Enthusiastic Customers
We create success for our customers by identifying their
needs and providing innovative and value-adding solutions.
1.2 Units
4 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
2.1.2 Concrete
ASTM
Concrete
Type
Aggregate Grading
Specification
Concrete Unit
Weight pcf
Normal Weight
ASTM C33
145-155
Sand Lightweight
ASTM C330
105-115
All Lightweight
ASTM C 330
85-110
Lightweight
ASTM C 332
15-90
Insulating Concrete
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 5
2.1.3.2 Mortar
Minimum face-shell
Minimum web
ThicknessA
ThicknessA
in. (mm)
in. (mm)
in. (mm)
3/4 (19)
3/4 (19)
6 (152)
1 (25)
1 (25)
8 (203)
1-1/4 (32)
1 (25)
10 (254)
1-3/8 (35)
1-1/8 (29)
Width of Unit
1-1/4 (32)
12 (305)
1-1/2 (38)
1-1/8 (29)
1-1/4 (32)B
Adapted from ASTM C90.
A Average of measurements on three units taken at the thinnest
point.
B This face-shell thickness is applicable where the allowable design
load is reduced in proportion to the reduction in thickness from
the basic face-shell thickness shown.
7 5\8"
7 5\8"
8"
16"
Nominal Size
(usually fictitious)
15 5/8"
Modular Size
(actual)
Masonry Cement
Type
Average Compressive
Strength at 28 Days,
Min psi (MPa)
2500
(17.2)
1800
(12.4)
750
(5.2)
350
(2.4)
2500
(17.2)
1800
(12.4)
750
(5.2)
350
(2.4)
2.1.3.3 Grout
6 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
2.1.6 Steel
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 7
2.1.10 Admixtures
Fall = F
v
8 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Corrosion 2.3
2.3.1 The Corrosion Process
2.3.2.2 Electrochemical
Contact Corrosion
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 9
2.3 Corrosion
The effects of electrochemical contact corrosion may be
mitigated by:
a. Using similar metals close together in the electromotive
force series,
b. Separating dissimilar metals with gaskets, plastic washers
or paint with low electrical conductivity. Materials typically
used in these applications include:
1. High Density Polyethylene (HDPE)
2. Polytetrafluoroethylene (PTFE)
3. Polycarbonates
4. Neoprene/chloroprene
5. Cold galvanizing compound
6. Bituminous coatings or paint
Note: Specifiers must ensure that these materials are
compatible with other anchorage components in the service
environment.
c. Selecting materials so that the fastener is the cathode, most
noble or protected component,
d. Providing drainage or weep holes to prevent entrapment of
the electrolyte
Urban Non-Industrial
or Marine
Suburban
1.5 m/year
Rural
0.8 m/year
Considerably less
than 0.5 m/year
Indoors
5.6 m/year
1.3 m/year
10 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Corrosion 2.3
2.3.3.1 Suggested Corrosion
Resistance
0 hours
12 hours
Duplex Coating
(comparable to
45 m HDG)
250-480 hours
Hot-Dip Galvanizing
(HDG) > 50 m
(ASTM A153)
300-500 hours
Thick Mechanical
Plated (> 86 m)
(ASTM B695)
400-800 hours
Organic Coatings
(Kwik-Cote)
1000 hours
Stainless Steel
(SAE 303 / 304)
Stainless Steel
(SAE 316)
Typical Conditions
of Use
Interior applications
without any particular
influence of moisture
N/A
N/A
Near saltwater
Exterior corrosive
environments
Sulfur Dioxide
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 11
2.3 Corrosion
2.3.6 Applications
It is difficult to offer generalized solutions to corrosion problems. An applications guide can be useful as a starting point for
fastener material selection. The specifier should also consult:
a. Local and national building code requirements (e.g., IBC, IRC)
b. Standard practice manuals for specific types of construction (e.g., ACI, PCI, AISC, PCA, CRSI, AASHTO, NDS/APA)
c. Manufacturers of structural components
d. Hilti Technical Support
Conditions
Fastener Recommendations
Stainless steel
X-CR
X-CR
Interior applications
Exterior applications
Parking garages / parking decks subject to periodic application of de-icers including chloride
solutions 7
Non-safety critical
Safety critical
Stainless steel1
Road / bridge decks subject to periodic application of de-icers including chloride solutions
Non-safety critical
Safety critical
Stainless steel
Refer to Factory Mutual Approval Standard Class No. 4450 Section 5.4
Refer to Factory Mutual Approval Standard Class No. 4470 Section 5.6
Refer to ICC Evaluation Services Acceptance Criteria 24 Exterior Insulation and Finish Systems
Refer to PCI Parking Structures: Recommended Practice for Design & Construction Chapters 3, 5 and Appendix
General guidelines address environmental corrosion (direct chemical attack). Additional considerations should be taken into account when
using hardened steel fasteners susceptible to HASCC. The reference to "non-safety critical" is intended to distinguish applications where
failure of the attachment will not create any potential safety risks or significant damage.
12 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Corrosion 2.3
2.3.6.2 Special Applications
These application charts are offered as general guidelines.4 Site specific conditions may influence the decision.
Application
Conditions
Fastener Recommendations
Aluminum fastenings (flashing / roofing accessories, hand rails, grating panels, sign posts and
miscellaneous fixtures)
Water treatment
Not submerged
Submerged
Stainless steel 2
Not submerged
Submerged
Stainless steel 2
Stainless steel1
Non-safety critical
Stainless steel1
Above grade
HDG
Below grade
Non-safety critical
Non-safety critical
Safety critical
Stainless steel1
Must electrically isolate fastener from contact with concrete reinforcement through use of adhesive or epoxy anchoring system, gasket
or plastic washer with low electrical conductivity.
Refer to APA Technical Note No. D485D and AF & PA Technical Report No. 7.
General guidelines address environmental corrosion (direct chemical attack). Additional considerations should be taken into account
when using hardened steel fasteners susceptible to HASCC. The reference to "non-safety critical" is intended to distinguish applications
where failure of the attachment will not create any potential safety risks or significant damage.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 13
14 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 15
tf
G'
Fy
Qf
fc
Sf
f'c
Fastening Details
hr
Hs
Nr
Qn
Rg
wr
Ls
tI
tI
tII
Fastener Nomenclature
Fastener
Series1
X-U 37 P8 MX
Stud Nomenclature
1. P = Plastic washer
S = Steel washer
D = Double washer
(1 plastic, 1 steel)
L = Double washer (both steel)
DP = Double washer (both plastic)
FP = Plastic ferrule and guide washer
Indicates
Collated Fastener2
(strips of 10)
Shank Length
(mm)
Thread Size
(mm)
X-W6 20 22 FP8
Shank Length
(mm)
Washer
Shank Diameter
Shank Diameter
Thread Length
(mm)
Washer
Thread Length
Thread Size
16 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
General
Fastenings
to Steel
Reference
Sections 3.2.2,
3.2.3 and 3.2.8
Reference
Sections 3.2.2,
3.2.3 and 3.2.9
Structural
Wood Panel
Sheathing
Interior Partition
Walls
(Drywall Track
Attachment)
Reference
Section 3.2.5
Electrical
Grounding
Reference
Section 3.2.10
Thermal
Insulation
Attachment
Reference
Section 3.2.12
Steel Deck
Attachment
Reference
Section 3.5
Reference
Section 3.2.6
Pipe Hangers
Reference
Sections 3.2.8,
3.2.9 and 3.2.11
Ceiling Hangers
Reference
Section 3.3
Perimeter Wall
Applications
- Deflection
Slip Clips
- Steel Framing
Track
Reference
Section 3.2.4
Wood Sill Plate
Attachment
Reference
Section 3.2.7
Cable and
Conduit
Attachment
Reference
Section 3.2.11
Grating and
Checkerplate
Attachment
Reference
Section 3.4
Steel Deck
Sidelap
Attachment
Cold-Formed
Steel Framing
Connections
Reference Sections
3.5 and 3.6
Reference
Section 3.6
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 17
Sintering Zone
Compression
Zone
Depth of penetration
Compressive strength
of the concrete
Sprinkler Installations
with W10 Stud Only
Concrete block
and joints
3/4" to 1"
(19 to 25 mm)
Average concrete
(2000-4000 psi)
3/4" to 1-1/4"
(19 to 32 mm)
1" to 1-5/8"
(25 to 41 mm)
3/4" to 1"
Precast or prestressed
concrete (5000 psi +)
(19 to 25 mm)
1" to 1-1/4"
(25 to 32 mm)
Material
1 For allowable load capacities at specific embedment depths refer to specific product sections.
Maximum
(3.0) (X-GN)
2-3/8 (60)
2-3/8 (60)
0.138
(3.5) (X-C)
2-3/4 (70)
2-3/4 (70)
0.145
(3.7) (X-CR)
2-3/4 (70)
2-3/4 (70)
0.157
(4.0) (X-U)
2-3/4 (70)
2-3/4 (70)
0.177
2-3/4 (70)
0.177
(4.5) (DS)
3-1/8 (80)
0.205
(5.2) (W10)
3-1/8 (80)
4
(104)
Smin
Cmin
t II
Depth of
Penetration
(104)
Stud Type
X-W6
3.0 (4.0)
X-CR W6
3.0 (4.0)
W10
4.5 (6.0)
18 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
12"
min. 3-1/4"
3"
Form Deck
Lower Flute Location
Upper Flute Location
4-1/2" min.
Direction of
shear load
on fastener
4-1/2" min.
1-1/8"
Min. Edge
Distance
7-1/4" min.
Direction of
tension load
on fastener
Figure 1: Hilti Fastener Location in 3" Deep Composite Floor Deck Normal Deck Profile Orientation
Direction of
shear load
on fastener
Form Deck
Upper Flute Location
Lower Flute Location
Direction of
tension load
on fastener
7/8"
Edge
Distance
1-3/4"
min. 2-1/2"
1-1/2"
2-1/2"
3-1/2"
Figure 2: Hilti Fastener Location in 1-1/2" Deep Composite Floor Deck Normal Deck Profile Orientation
Hilti Power-Driven Fastener
6"
Form Deck
Direction of
shear load
on fastener
Direction of
tension load
on fastener
1-3/4"
Edge
Distance
min. 2-1/2"
1-3/4"
1-1/2"
3-1/2"
Figure 3: Hilti Fastener Location in 1-1/2" Deep Composite Floor Deck Inverted Deck Profile Orientation
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 19
Non-symmetric arrangement:
Moment on fastened part
Prying effect must be considered in
determining loads acting on fastener
Coupler not
tight against
concrete
Coupler tight
against concrete
tl
tl
DX KWIK Fasteners
DX KWIK
Anchor
DX 460
Powder-Actuated Fastening Tool
Standard DX
23 mm
5 mm
Note:
Typically, DX KWIK
fasteners are 47 mm
minimum in length.
As of publication date,
only X-U series fasteners
have been tested. Reference Section 3.2.3.3 for
allowable load capacity
table.
* These are abbreviated instructions which may vary by application. ALWAYS review/follow the instructions accompanying the product.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 21
Smin
Cmin
t II
Holding Power
Optimum Thickness
3/8" to 1/2"
(10 to 12 mm)
Steel Thickness
Application Range
for Standard
Knurled Fasteners
tI
LS
hET
L S = hET + t I
LS
hET
X-U
X-U 15
X-EW6H-xx-9
EDS
X-EGN
X-GHP
X-EW10H-xx-14
DS
X-S13 P8THP
X-S16 P8TH
X-CR
mm
10 - 14
11 - 14
8 - 11
12 - 17
8 -11
8-16
13 - 16
17 - 27
10 -12
> 11
> 10
22 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
X-U
Wood
Thickness
(mm)
Up to 1/4" (6 mm)
5/16" (8 mm) 3/8" (10 mm) 7/16" (11 mm) 1/2" (12 mm)
and
4 Based upon a base steel tensile strength (Fu ) of less than or equal to 70 ksi.
Tightening-Torque
Tmax
Stud Type
Tmax
X-EW6H
X-EW10H
X-CRM8
X-BT
W6, W10 and M8
3.0 (4.1)
11.0 (14.9)
6.0 (8.1)
6.0 (8.1)
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 23
Arrangement causing
moment to act on shank:
Non-symmetric arrangement:
Moment on fastened part
Prying effect must be considered in
determining loads acting on fastener
Coupler tight
against steel
tl
tl
24 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
2
2
3
1
4
2
4.5
2
5
2
6
2
White
Green
Yellow
Blue
Red
Black
DX 35
DX 351 ONLY
DX 36
DX 460
DX 351
4
5
DX 76
DX 600N
4.5
DX 460 ONLY
DX 76 ONLY
6
Concrete 6000 psi
Steel
Fastener
X-U Fastener
X-U MX Magazine
DS/EDS Fastener
X-C Fastener
X-CR Corrosion
Resistant Fastener
DX 600N
DX 76
DX 460
DX 36
DX 351
Fastener Notes:
= Single
M = Collated Fasteners (magazine required)
P8 = 8 mm fastener guide required
P10 = 10 mm fastener guide required
DX 35
Section
Numbers
Page
Numbers
3.2.2
3.2.3
3.2.4
29-33
34-36
37-41
3.2.2
3.2.3
3.2.4
29-33
34-36
37-41
3.2.2
3.2.4
29-33
37-41
3.2.2
29-33
3.2.2
29-33
3.2.2
29-33
Application
For universal, high quality
fastenings to concrete and steel:
perimeter wall applications,
forming, underfloor, thin metal
brackets, angles, etc.
P10
2013
Direct Fastening
Technical Guide
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 25
Fastener
Application
X-CT Fastener
Single and Collated
BC
Rebar Basket
Clip
X-GPN 37 MX
X-U 15
Stepped-Shank Fastener
X-S16 Fastener
X-GN/X-EGN
Gas Fastener Collated
X-GHP
Gas Fastener Collated
Gas-actuated hardened
fastener specifically designed
for attaching drywall track and
cold-formed steel to higher
strength concrete.
X-CF Fastener
X-CP Fastener
GX 120
GX 120 ME
DX 460
DX 36
DX 351
Fastener Notes:
= Single
M = Collated Fasteners (magazine required)
P8 = 8 mm fastener guide required
DX 35
2013
Direct Fastening
Technical Guide
Section
Page
Numbers Numbers
3.2.2
29-33
3.2.2
29-33
3.2.5
42-48
3.2.2
3.2.6
29-33
49-52
P8
3.2.2
3.2.4
3.2.6
29-33
37-41
49-52
3.2.2
3.2.6
49-52
3.2.2
3.2.6
29-33
49-52
3.2.2
3.2.6
29-33
49-52
3.2.7
53-54
3.2.7
53-54
26 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Fastener
Application
X-W6 1/4"
Threaded Stud
P8
P8
P8
DX 600N
GX 120 ME
DX 460
DX 36
DX 351
Fastener Notes:
= Single
M = Collated Fasteners (magazine required)
P8 = 8 mm fastener guide required
P10 = 10 mm fastener guide required
DX 35
P8
2013
Direct Fastening
Technical Guide
Section
Numbers
Page
Numbers
3.2.8
55-57
3.2.8
55-57
3.2.9
58-60
3.2.9
58-60
3.2.9
3.2.10
58-60
61-65
W10 3/8"
Threaded Stud
X-EW6H 1/4"
Threaded Stud
X-EW10H 3/8"
Threaded Stud
X-BT
Threaded Stud
X-RH
Rod Hanger
X-HS
Threaded Rod
Hanger
X-HS MX
Threaded Rod
Hanger
X-EMTC/BX
Conduit and
Cable Clip
X-EMTC/BX MX
Conduit and
Cable Clip
P10
P8
P8
P8
P8
P10
BT
Tool
3.2.11
66-70
3.2.11
66-70
3.2.11
66-70
3.2.11
66-70
3.2.11
66-70
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 27
Fastener
Application
X-EMTSC MX
Stand-Off
Conduit Clip
X-ECH
Cable Holder
X-EKB MX
Cable Clamp
X-IE
Insulation
Fastener
X-SW
Soft Washer
Section
Numbers
Page
Numbers
3.2.11
66-70
3.2.11
66-70
GX 120 ME
DX 460
DX 36
3.2.11
66-70
3.2.11
66-70
3.2.12
71-72
3.2.12
71-72
3.3
73-82
3.4
83-93
3.5
94-147
3.6
148-170
Ceiling Fastening
Systems
Self-Drilling Screw
Fasteners
2013
Direct Fastening
Technical Guide
X-ECT MX
Cable Tie
Fastener
Steel Deck
Fastening Systems
DX 351
Fastener Notes:
= Single
M = Collated Fasteners (magazine required)
P8 = 8 mm fastener guide required
DX 35
28 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
3.2.2.1
Product Description
Technical Data
3.2.2.4
Ordering Information
X-C
DS
X-CR
X-S
EDS
X-U 15
Listings/Approvals
ICC-ES (International Code Council)
ESR-2269 (X-U and X-U 15)
ESR-1663 (DS, X-C, EDS and X-CR)
COLA (City of Los Angeles)
RR 25675 (X-U and X-U 15)
RR 25646 (DS, X-C, EDS, and X-CR)
Fastener
Material
Carbon Steel
Carbon Steel
Carbon Steel
SAE 316
Carbon Steel
Carbon Steel
Carbon Steel
Fastener
Plating1
5 m Zinc
5 m Zinc
5 m Zinc
N/A
2-10 m Zinc
5 m Zinc
5 m Zinc
Washer or Clip
Material1,2
Carbon Steel
N/A
Carbon Steel
SAE 316
N/A
N/A
Carbon Steel
* More details about the innovative X-U fastener can be found in Section 3.2.3.
Washer or
Clip Plating1,2
5 m Zinc
N/A
5 m Zinc
N/A
N/A
N/A
5 m Zinc
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 29
Description
Fastener
X-U*
Standard Fastener
X-C
DS
X-CR
Gas Fastener
X-GN
Shank
Diameter
in. (mm)
X-GHP
X-CT 473
X-CT 623
Minimum
Embedment
in. (mm)
3/4
1
0.157 (4.0)
1-1/4
1-1/2
3/4
1
0.138 (3.5)
1-1/4
1-1/2
3/4
1
0.177 (4.5)
1-1/4
1-1/2
3/4
0.145 (3.7)
1
&
1-1/4
0.157 (4.0)
1-1/2
3/4
0.118 (3.0)
1
0.118 (3.0) 5/8
1
0.145 (3.7)
1
0.145 (3.7)
(19)
(25)
(32)
(38)
(19)
(25)
(32)
(38)
(19)
(25)
(32)
(38)
(19)
(25)
(32)
(38)
(19)
(25)
(16)
(25)
(25)
100
165
240
275
45
85
130
175
50
130
220
300
30
55
110
265
95
115
(0.44)
(0.73)
(1.07)
(1.22)
(0.20)
(0.38)
(0.58)
(0.78)
(0.22)
(0.58)
(0.98)
(1.33)
(0.13)
(0.24)
(0.49)
(1.18)
(0.42)
(0.51)
125
190
310
420
75
150
210
260
120
195
385
405
40
185
290
405
120
220
(0.27)
(0.33)
65
75
60
75
(0.57)
(0.85)
(1.38)
(1.87)
(0.33)
(0.67)
(0.93)
(1.16)
(0.53)
(0.87)
(1.71)
(1.80)
(0.18)
(0.82)
(1.29)
(1.80)
(0.53)
(0.98)
(0.29)
(0.33)
100
170
280
325
60
90
130
245
125
155
270
355
65
120
125
350
95
115
50
(0.44)
(0.76)
(1.25)
(1.45)
(0.27)
(0.40)
(0.58)
(1.09)
(0.56)
(0.69)
(1.20)
(1.58)
(0.29)
(0.53)
(0.56)
(1.56)
(0.42)
(0.51)
(0.22)
125
225
310
420
105
200
290
360
135
240
425
450
40
190
300
450
120
220
120
(0.57)
(1.00)
(1.38)
(1.87)
(0.47)
(0.89)
(1.29)
(1.60)
(0.60)
(1.07)
(1.89)
(2.00)
(0.18)
(0.85)
(1.33)
(2.00)
(0.53)
(0.98)
(0.53)
50 (0.22) 90 (0.40)
1 The tabulated allowable load values are for the low-velocity fasteners only, using a safety factor that is greater than or equal to 5.0, calculated in accordance with
ICC-ES AC70. Wood or steel members connected to the substrate must be investigated in accordance with accepted design criteria.
2 Multiple fasteners are recommended for any attachment.
3 For temporary fastening of formwork only.
Fastener
Shank
Diameter
in. (mm)
X-U*
0.157
(4.0)
Standard Fastener
X-C
0.138
(3.5)
DS4
0.177
(4.5)
X-CR
0.145
(3.7)
&
0.157 (4.0)
X-GN
0.118
(3.0)
X-GHP
0.118
(3.0)
Minimum
Embedment
in. (mm)
(19)
3/4
1
(25)
1-1/4 (32)
1-1/2 (38)
(19)
3/4
1
(25)
1-1/4 (32)
1-1/2 (38)
(19)
3/4
1
(25)
1-1/4 (32)
1-1/2 (38)
1
(25)
1-1/4 (32)
1-1/2 (38)
(19)
3/4
1
(25)
(16)
5/8
Fastener Location
Installed Through 3" Deep
Installed into Concrete
Metal Deck into Concrete2,3
Tension lb (kN)
Tension
Shear
Shear
lb (kN)
lb (kN)
lb (kN)
Upper Flute Lower Flute
125 (0.56) 115 (0.51) 130 (0.58) 95 (0.42) 245 (1.09)
205 (0.91) 260 (1.16) 215 (0.96) 155 (0.69) 330 (1.47)
315 (1.40) 435 (1.93) 295 (1.31) 200 (0.89) 375 (1.67)
425 (1.89) 475 (2.11) 400 (1.78) 260 (1.16) 430 (1.91)
110 (0.49) 175 (0.78) 120 (0.53)
265 (1.18)
135 (0.60) 180 (0.80) 215 (0.96) 145 (0.64) 315 (1.40)
220 (0.98) 260 (1.16) 250 (1.11) 200 (0.89) 405 (1.80)
285 (1.27) 315 (1.40) 285 (1.27) 210 (0.93) 415 (1.85)
100 (0.44) 200 (0.89) 100 (0.44)
200 (0.89)
180 (0.80) 360 (1.60) 180 (0.80) 180 (0.80) 405 (1.80)
300 (1.33) 520 (2.31) 300 (1.33) 250 (1.11) 515 (2.29)
450 (2.00) 680 (3.02) 450 (2.00) 325 (1.45) 625 (2.78)
230 (1.02) 240 (1.07) 230 (1.02)
240 (1.07)
320 (1.42) 400 (1.78) 320 (1.42)
400 (1.78)
405 (1.80) 500 (2.22) 405 (1.80)
500 (2.22)
115 (0.51) 140 (0.62) 75 (0.33) 85 (0.38) 175 (0.78)
170 (0.76) 220 (0.98) 155 (0.69) 160 (0.71) 255 (1.13)
60 (0.27) 140 (0.62) 60 (0.27) 60 (0.27) 175 (0.78)
1 The tabulated allowable load values are for the low-velocity fasteners only, using a safety factor that is greater than or equal to 5.0, calculated in accordance with
ICC-ES AC70. Wood or steel members connected to the substrate must be investigated in accordance with accepted design criteria.
2 The steel deck profile is 3" deep composite floor deck with a minimum thickness of 20 gauge (0.0358"). Figure 1 (Section 3.2.1.1.6) shows the nominal flute
dimensions, fastener locations, and load orientations for the deck profile.
3 Structural lightweight concrete fill above top of metal deck shall be a minimum of 3-1/4" deep.
4 DS fasteners installed at 1-1/2" embedment through steel deck into the lower flute must be installed at a minimum distance of 6" from the edge of the floor deck.
5 Multiple fasteners are recommended for any attachment.
* More details about the innovative X-U fastener can be found in Section 3.2.3.
30 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Fastener
Shank Diameter
Universal Knurled
Shank Fastener
in.
(mm)
X-U*
0.157
(4.0)
Standard Fastener
X-C
0.138
(3.5)
X-GN
0.118
(3.0)
X-GHP
0.118
(3.0)
Gas Fastener
Premium Gas Fastener
Fastener Location
Installed Through Metal Deck into Concrete2,3
Tension lb (kN)
Shear
Upper Flute
Lower Flute
lb (kN)
95 (0.42)
95 (0.42)
370 (1.65)
125 (0.56)
125 (0.56)
415 (1.85)
80 (0.36)
80 (0.36)
315 (1.40)
205 (0.91)
205 (0.91)
445 (1.98)
75 (0.33)
85 (0.38)
175 (0.78)
155 (0.69)
160 (0.71)
255 (1.13)
60 (0.27)
60 (0.27)
175 (0.78)
Minimum
Embedment
in.
3/4
1
3/4
1
3/4
1
5/8
(mm)
(19)
(25)
(19)
(25)
(19)
(25)
(16)
1 The tabulated allowable load values are for the low-velocity fasteners only, using a safety factor that is greater than or equal to 5.0, calculated in accordance with
ICC-ES AC70. Wood or steel members connected to the substrate must be investigated in accordance with accepted design criteria
2 Steel deck profiles are 1-1/2" deep, B-type deck with a minimum thickness of 20 gauge (0.0358" thick steel). Fasteners may be installed through the metal deck
into lightweight concrete having both nominal and inverted deck profile orientations with a minimum lower flute width of 1-3/4" or 3-1/2", respectively. Fasteners
shall be placed at centerline of deck flutes. Refer to Figures 2 and 3 (Section 3.2.1.1.6) for additional flute dimensions, fastener locations, and load orientations
for both deck profiles.
3 Structural lightweight concrete fill above top of metal deck shall be a minimum 2-1/2" deep.
4 Multiple fasteners are recommended for any attachment.
The tabulated allowable load values are for the low-velocity fastener
only, using a safety factor of 5.0 or higher calculated in accordance with
ICC-ES AC70. Wood or steel members connected to the substrate must be
investigated in accordance with accepted design criteria.
2 The tabulated allowable load values are for low-velocity fasteners installed in
normal weight or lightweight concrete masonry units conforming to ASTM C90.
3 The tabulated allowable load values are for low-velocity fasteners installed in
concrete masonry units with mortar conforming to ASTM C270, Type N or S.
4 The tabulated allowable load values are for low-velocity fasteners installed in
concrete masonry units with grout conforming to ASTM C476, as coarse grout.
5 The tabulated allowable load values are for one low-velocity fastener installed in
an individual masonry unit cell and at least 4" from the edge of the wall.
6 Fastener can be located anywhere on the face shell or mortar joint as shown in
the figure to the right.
7 Shear direction can be horizontal or vertical (Bed Joint or T-Joint) along the
CMU wall plane.
8 Fastener located in center of grouted cell installed vertically.
9 Shear can be in any direction.
10 Multiple fasteners are recommended for any attachment.
#FE+PJOU
$PODSFUF
.BTPOSZ
5+PJOU
6OJU
$.6
* More details about the innovative X-U fastener can be found in Section 3.2.3.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 31
Fastener
X-U6
Stepped-Shank
Knurling-Lengthwise
Standard Smooth Shank
Drywall Smooth Shank
w/Metal Top Hat Washer
Heavy Duty
Knurled Shank
Heavy Duty
Smooth Shank
Stainless Steel
Smooth Shank
Drywall Track
Smooth Shank
Premium Gas Fastener
1
2
3
4
5
6
7
8
9
X-U 157
X-S13
X-S16
EDS3
DS
X-CR
X-CR8
X-EGN9
X-EGN8,9
X-GHP
Shank
Diameter
in.
(mm)
0.157
(4.0)
0.145
(3.7)
0.145
(3.7)
0.145
(3.7)
0.177
(4.5)
0.177
(4.5)
0.145
(3.7)
0.145
(3.7)
0.118
(3.0)
0.118
(3.0)
0.118
(3.0)
1/8
Tension Shear
lb (kN) lb (kN)
140
300
(0.62) (1.33)
300
210
(1.33) (0.93)
140
230
(0.62) (1.02)
3/16
125
230
(0.56) (1.02)
Tension
lb (kN)
535
(2.38)
155
(0.69)
300
(1.33)
225
(1.00)
330
(1.47)
395
(1.76)
485
(2.16)
630
(2.80)
220
(0.98)
220
(0.98)
170
(0.76)
Shear
lb (kN)
720
(3.20)
395
(1.76)
450
(2.00)
420
(1.87)
665
(2.96)
795
(3.54)
480
(2.14)
510
(2.27)
245
(1.09)
295
(1.31)
245
(1.09)
Tension
lb (kN)
775
(3.45)
230
(1.02)
300
(1.33)
225
(1.00)
665
(2.96)
620
(2.76)
700
(3.11)
850
(3.78)
225
(1.00)
260
(1.16)
200
(0.89)
Shear
lb (kN)
720
(3.20)
395
(1.76)
450
(2.00)
430
(1.91)
935
(4.16)
855
(3.80)
560
(2.49)
560
(2.49)
290
(1.29)
355
(1.58)
230
(1.02)
Tension
lb (kN)
Shear
lb (kN)
935
(4.16)
420
(1.86)
300
(1.33)
225
(1.00)
800
(3.56)
775
(3.45)
720
(3.20)
450
(2.00)
450
(2.00)
430
(1.91)
970
(4.31)
855
(3.80)
265
(1.18)
280
(1.25)
280
(1.25)
250
(1.11)
1/2
3/4
Tension
lb (kN)
Shear
lb (kN)
Tension Shear
lb (kN) lb (kN)
900
720
350
375
(4.00) (3.20) (1.56) (1.67)
365
500
365
400
(1.62) (2.22) (1.62) (1.78)
225
430
(1.00) (1.91)
890
995
400
655
(3.96) (4.43) (1.78) (2.91)
800
895
(3.56) (3.98)
395
265
395
(1.13)
The tabulated allowable load values are for the low-velocity fasteners only, using a safety factor that is greater than or equal to 5.0, calculated in accordance
with ICC-ES AC70. Wood or steel members connected to the substrate must be investigated in accordance with accepted design criteria.
Low-velocity fasteners shall be driven to where the point of the fastener penetrates the steel base material in accordance with Section 3.2.1.2.3, except as
noted in this table.
EDS fasteners installed into greater than 1/2" thick steel require 1/2" minimum penetration.
Multiple fasteners are recommended for any attachment.
Refer to guidelines for fastening to steel, Section 3.2.1.2, for application limits.
Tabulated allowable load values provided for 3/4" steel are based upon minimum point penetration of 1/2". If 1/2" point penetration is not achieved, but a
point penetration of at least 3/8" is obtained, the tabulated tension value should be reduced by 20 percent and the tabulated shear load should be reduced by
8 percent.
X-U 15 fasteners installed into greater than 3/8" thick steel require 15/32" minimum penetration.
Based on testing with Fy = 50 ksi base material.
X-EGN fasteners installed into 3/8" or thicker base steel require 0.320" minimum penetration depth.
Allowable Tensile Pullover and Shear Bearing Load Capacities for Steel Framing with Power Driven Fasteners1,2,3,4
Sheet Steel Thickness
18 ga.
20 ga.
22 ga.
Head
Dia.
in.
(mm)
Tension Shear Tension Shear Tension Shear Tension Shear Tension Shear Tension Shear Tension Shear
lb (kN) lb (kN) lb (kN) lb (kN) lb (kN) lb (kN) lb (kN) lb (kN) lb (kN) lb (kN) lb (kN) lb (kN) lb (kN) lb (kN)
0.322
(8.2)
0.322
(8.2)
Fastener Description
Fastener
14 ga.
16 ga.
24 ga.
25/26 ga.
985
685
720
490
515
360
440
300
310
205
235
120
145
(4.38) (3.05) (3.20) (2.18) (2.29) (1.60) (1.96) (1.33) (1.38) (0.91) (1.05) (0.53) (0.64)
DS, EDS
0.322
(8.2)
X-S13 THP
X-S16 TH
0.322
(8.2)
985
685
720
490
515
360
440
300
310
205
235
120
145
(4.38) (3.05) (3.20) (2.18) (2.29) (1.60) (1.96) (1.33) (1.38) (0.91) (1.05) (0.53) (0.64)
325
390
265
335
250
235
170
185
100
125
(1.45) (1.73) (1.18) (1.49) (1.11) (1.05) (0.76) (0.82) (0.44) (0.56)
1 Allowable load values are based on a safety factor of 3.0 in accordance with the AISI S100.
2 Allowable pullover capacities of sheet steel should be compared to the allowable fastener tensile load capacities in concrete, steel, and masonry to determine
controlling resistance load.
3 Allowable shear bearing capacities of sheet steel should be compared to allowable fastener shear capacities in concrete, steel and masonry to determine
controlling resistance load.
4 Data is based on the following minimum sheet steel properties, Fy = 33 ksi, Fu = 45 ksi (ASTM A653 material).
* More details about the innovative X-U fastener can be found in Section 3.2.3.
32 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Shank Length
in. (mm)
Shank
in. (mm)
Washer
0.157 (4.0)
0.157 (4.0)
8 mm plastic
8 mm plastic and metal tophat
0.177 (4.5)
0.138 (3.5)
0.138 (3.5)
8 mm plastic
8 mm plastic
8 mm plastic tophat
1/2 (13)
5/8 (16)
3/4, 7/8 (19, 22)
0.145 (3.7)
0.145 (3.7)
0.177 (4.5)
8 mm plastic tophat
8 mm plastic and metal tophat
10 mm plastic
Shank Length
in. (mm)
Shank
in. (mm)
Washer
0.157 (4.0)
Collated
0.138 (3.5)
0.118 (3.0)
0.118 (3.0)
Collated
Collated
Collated
1/2 (13)
1/2 (14)
11/16, 3/4 (18, 20)
0.145 (3.7)
0.118 (3.0)
0.118 (3.0)
Collated
Collated
Collated
Shank Length
in. (mm)
Shank
in. (mm)
Washer
0.157 (4.0)
0.157 (4.0)
0.138 (3.5)
0.138 (3.5)
SAE 316 Stainless Steel Non-Collated (with and without pre-mounted steel washer)
Fastener
Description
Shank Length
in. (mm)
Shank
in. (mm)
Washer
0.145 (3.7)
0.157 (4.0)
0.145 (3.7)
0.157 (4.0)
8 mm plastic
8 mm plastic
8 mm plastic and 12 mm steel
8 mm plastic and 12 mm steel
0.145 (3.7)
0.145 (3.7)
8 mm plastic
12 mm steel
Shank
in. (mm)
Washer
0.145 (3.7)
Double 8 mm plastic
0.145 (3.5)
Shank Length
in. (mm)
Forming Nail
X-CT 47MX, X-CT 62 MX, X-CT 62 DP8 1-7/8, 2-7/16 (47, 62)
Rebar Basket Clip
BC X-C P8T
1-7/8, 2-7/16 (47, 62)
* More details about the innovative X-U fastener can be found in Section 3.2.3.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 33
Product Description
3.2.3.2
Material Specifications
3.2.3.3
Technical Data
3.2.3.4
Ordering Information
Product Features
A 0.157" shank diameter for high
performance in both tension and
shear applications
Unique knurling design offering
higher pullout strength and
anchorage in concrete and steel
Full range of fasteners in single
or collated configurations to
maximize productivity
Listings/Approvals
ICC-ES (International Code Council)
ESR-2269
COLA (City of Los Angeles)
RR 25675
Fastener
Material
Carbon Steel
Fastener
Plating
5 m Zinc1
Fastener
Hardness
58 HRC
1 ASTM B633, SC 1, Type III. Refer to Section 2.3.3.1 for more information.
Fastener
X-U
0.157
(4.0)
Minimum
Embedment
in. (mm)
3/4
1
1-1/4
1-1/2
(19)
(25)
(32)
(38)
2000 psi
Tension
Shear
lb (kN)
lb (kN)
100
165
240
275
(0.44)
(0.73)
(1.07)
(1.22)
125
190
310
420
100
170
280
325
(0.57)
(0.85)
(1.38)
(1.87)
(0.44)
(0.76)
(1.25)
(1.45)
125
225
310
420
(0.57)
(1.00)
(1.38)
(1.87)
6000 psi
Tension
Shear
lb (kN)
lb (kN)
105
110
180
(0.47)
(0.49)
(0.80)
205
280
425
(0.91)
(1.25)
(1.89)
1 The tabulated allowable load values are for the low-velocity fasteners only, using a safety factor that is greater than or equal to 5.0, calculated in accordance with
ICC-ES AC70. Wood or steel members connected to the substrate must be investigated in accordance with accepted design criteria.
Shank
Diameter
in. (mm)
0.157
(4.0)
Minimum
Embedment
in. (mm)
1-1/2
(38)
4000 psi
Tension
lb (kN)
395
(1.76)
6000 psi
Shear
lb (kN)
405
(1.80)
Tension
lb (kN)
360
(1.60)
Shear
lb (kN)
570
(2.54)
1 X-U Fastener is installed using the DX-KWIK drilled pilot hole installation procedure shown in Section 3.2.1.1.10.
2 The tabulated allowable load values are for the low-velocity fasteners only, using a safety factor that is greater than or equal to 5.0, calculated in accordance
with ICC-ES AC70. Wood or steel members connected to the substrate must be investigated in accordance with accepted design criteria.
34 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Fastener
X-U
Shank
Dia.
in. (mm)
Installed into
Concrete
Minimum
Embed.
in. (mm)
Tension
lb (kN)
3/4 (19) 125 (0.56)
1
(25) 205 (0.91)
0.157 (4.0)
1-1/4 (32) 315 (1.40)
1-1/2 (38) 425 (1.89)
Shear
lb (kN)
115 (0.51)
260 (1.16)
435 (1.93)
475 (2.11)
Fastener Location
Installed Through Metal Deck into Concrete
3 Inch Deep Composite Floor Deck2 1-1/2 Inch Deep Composite Floor Deck3
Tension lb (kN)
Tension lb (kN)
Shear
Shear
lb (kN)
lb (kN)
Upper Flute Lower Flute
Upper Flute Lower Flute
130 (0.58) 95 (0.42) 245 (1.09) 95
95
(0.42)
(0.42) 370 (1.65)
215 (0.96) 155 (0.69) 330 (1.47) 125 (0.56) 125 (0.56) 415 (1.85)
295 (1.31) 200 (0.89) 375 (1.67)
1 The tabulated allowable load values are for the low-velocity fasteners only, using a safety factor that is greater than or equal to 5.0, calculated in accordance with
ICC-ES AC70. Wood or steel members connected to the substrate must be investigated in accordance with accepted design criteria.
2 The steel deck profile for the 3" deep composite floor deck has a minimum thickness of 20 gauge (0.0358") and a minimum Fy of 33 ksi. Lower and upper flute
width must be a minimum of 4-1/2". Figure 1 in Section 3.2.1.1.6 shows the nominal flute dimensions, fastener locations and load orientations for the deck
profile. Structural lightweight concrete fill above top of steel deck must be minimum 3-1/4".
3 The steel deck profile for the 1-1/2" deep composite floor deck has a minimum thickness of 20 gauge (0.0358") and a minimum Fy of 33 ksi. Lower flute and
upper flute widths must be a minimum of 1-3/4" and 3-1/2", respectively. This deck may also be inverted as shown in Figure 3 in Section 3.2.1.1.6. Figures 2
and 3 in Section 3.2.1.1.6 show the nominal flute dimensions, fastener locations and load orientations for the deck profile. Structural lightweight concrete fill
above top of steel deck must be minimum 2-1/2".
4 Multiple fasteners are recommended for any attachment.
0.157 (4.0)
Minimum
Embed.
in. (mm)
1
(25)
Face Shell6
Tension
lb (kN)
70 (0.31)
Shear
lb (kN)
85 (0.38)
Grout-Filled CMU
Mortar Joint6
Tension
lb (kN)
25 (0.11)
Face Shell6
Mortar Joint6
Tension
Shear
Tension
Tension
Shear
Shear
Shear9
lb (kN)
lb (kN)
lb (kN)
lb (kN)
lb (kN)
lb (kN)
lb (kN)
70 (0.31) 225 (1.00) 220 (0.98) 150 (0.67) 190 (0.85) 165 (0.73) 240 (1.07)
7
The tabulated allowable load values are for the low-velocity fastener into concrete
masonry units only, using a safety factor equal to or greater than 5.0, calculated
in accordance with ICC-ES AC70. Wood or steel members connected to the
substrate must be investigated in accordance with accepted design criteria.
The tabulated allowable load values are for low-velocity fasteners installed in
normal weight or lightweight concrete masonry units conforming to ASTM C90.
The tabulated allowable load values are for low-velocity fasteners installed in
concrete masonry units with mortar conforming to ASTM C270, Type S.
The tabulated allowable load values are for low-velocity fasteners installed in
concrete masonry units with grout conforming to ASTM C476.
The tabulated allowable load values are for one low-velocity fastener
installed in an individual masonry unit cell and at least 4" from the edge
of the wall.
Fastener can be located anywhere on the face shell or mortar joints as shown
in the figure to the right.
Shear load direction can be horizontal or vertical (Bed Joint or T-Joint) along
the CMU wall plane.
#FE+PJOU
$PODSFUF
.BTPOSZ
5+PJOU
1"
6OJU
$.6
Shank
Dia.
in. (mm)
0.157 (4.0)
3/16
Tension
lb (kN)
535 (2.38)
Shear
lb (kN)
720 (3.20)
1/4
Tension
lb (kN)
775 (3.45)
3/8
Shear
lb (kN)
720 (3.20)
Tension
lb (kN)
935 (4.16)
1/2
Shear
lb (kN)
720 (3.20)
Tension
lb (kN)
900 (4.00)
Shear
lb (kN)
720 (3.20)
3/43
Tension
lb (kN)
350 (1.56)
Shear
lb (kN)
375 (1.67)
1 The tabulated allowable load values are for the low-velocity fasteners only, using a safety factor that is greater than or equal to 5.0, calculated in accordance with
ICC-ES AC70. Wood or steel members connected to the substrate must be investigated in accordance with accepted design criteria.
2 Low-velocity fasteners shall be driven to where the point of the fastener penetrates the steel base material, except as noted.
3 Tabulated allowable load values provided for 3/4" steel are based upon minimum point penetration of 1/2". If 1/2" point penetration is not achieved, but a
point penetration of at least 3/8" is obtained, the tabulated tension value should be reduced by 20 percent and the tabulated shear load should be reduced by
8 percent.
4 Multiple fasteners are recommended for any attachment.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 35
X-U
0.322 825
(8.2) (3.67)
1,085
(4.83)
685
(3.05)
720
(3.20)
490
(2.18)
525
(2.34)
360
(1.60)
445
(1.98)
300
(1.33)
330
(1.47)
205
(0.91)
255
(1.13)
120
(0.53)
145
(0.64)
1 Allowable load values are based on a safety factor of 3.0 in accordance with the AISI S100.
2 Allowable pullover capacities of sheet steel should be compared to allowable fastener tensile load capacities in concrete, steel, or masonry to determine
controlling resistance load.
3 Allowable shear load bearing capacities of sheet steel should be compared to allowable fastener shear capacities in concrete, steel or masonry to determine
controlling resistance load.
4 Data is based on the following minimum sheet steel properties, Fy = 33 ksi, Fu = 45 ksi (ASTM A653 material).
Shank Length
in. (mm)
Shank
in. (mm)
Washer
Packaging Qty
X-U 16
X-U 19
X-U 22
X-U 27
X-U 32
X-U 37
X-U 42
X-U 47
X-U 52
X-U 57
X-U 62
X-U 72
5/8 (16)
3/4 (19)
7/8 (22)
1 (27)
1-1/4 (32)
1-1/2 (37)
1-5/8 (42)
1-7/8 (47)
2 (52)
2-1/4 (57)
2-1/2 (62)
2-7/8 (72)
0.157 (4.0)
0.157 (4.0)
0.157 (4.0)
0.157 (4.0)
0.157 (4.0)
0.157 (4.0)
0.157 (4.0)
0.157 (4.0)
0.157 (4.0)
0.157 (4.0)
0.157 (4.0)
0.157 (4.0)
Plastic 8 mm or collated
Plastic 8 mm or collated
Plastic 8 mm or collated
Plastic 8 mm or collated
Plastic 8 mm or collated
Plastic 8 mm or collated
Plastic 8 mm or collated
Plastic 8 mm or collated
Plastic 8 mm or collated
Plastic 8 mm or collated
Plastic 8 mm or collated
Plastic 8 mm or collated
Fastener
Description
Shank Length
in. (mm)
Shank
in. (mm)
Washer
Packaging Qty
X-U 22 P8 S15
X-U 27 P8 S15
X-U 32 P8 S15
X-U 32 P8 S36
X-U 72 P8 S36
7/8 (22)
1 (27)
1-1/4 (32)
1-1/4 (32)
2-7/8 (72)
0.157 (4.0)
0.157 (4.0)
0.157 (4.0)
0.157 (4.0)
0.157 (4.0)
Fastener
Description
Shank Length
in. (mm)
Shank
in. (mm)
Washer
Packaging Qty
X-U 16 P8 TH
X-U 19 P8 TH
X-U 27 P8 TH
5/8 (16)
3/4 (19)
1 (27)
0.157 (4.0)
0.157 (4.0)
0.157 (4.0)
36 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
3.2.4.1
Application Description
3.2.4.2
Product Description
3.2.4.3
Material Specifications
3.2.4.4
Technical Data
3.2.4.5
Ordering Information
X-U 15
DS
EDS
Listings/Approvals
ICC-ES (International Code Council)
ESR-2269 (X-U and X-U 15)
ESR-1663 (DS, EDS)
COLA (City of Los Angeles)
RR 25675 (X-U and X-U 15)
RR 25646 (DS, EDS)
DS/EDS
X-U 15
The X-U 15 is a high performance
fastener designed specifically for
attachments to steel. It is offered in a
0.145" shank diameter and 5/8" length.
Fastener
Material
Carbon Steel
Carbon Steel
Fastener
Plating
5 m Zinc1
5 m Zinc1
1 ASTM B633, SC 1, Type III. Refer to Section 2.3.3.1 for more information.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 37
2-1/4"
3-5/8"
2-1/4"
2-1/4"
2-1/4"
3-5/8"
3"
3"
3-5/8"
3-5/8"
2-1/4"
2-1/4"
2-1/4"
2-1/4"
3-5/8"
3"
Figure 1: 3-5/8" Track - 1 Fastener
3-5/8"
3"
3-5/8"
3-5/8"
2-1/4"
2-1/4"
2-1/4"
2-1/4"
6"4-1/2"
6"
4-1/2"
6"
6"
2-1/4"
2-1/4"
2-1/4"
6"
2-1/4"
6" 4-1/2"
4-1/2"
6"
6"
Allowable Shear Loads for Attachment of Perimeter Track to 4000 psi Normal Weight Concrete 1,2,3,4,5,6
Fastener
Description
Fastener
Shank Diameter
in. (mm)
Fastener Length
in. (mm)
Track
Width in.7
3-5/8
1
Universal
Knurled Shank
Fasteners
X-U
(27)
6
0.157
(4.0)
3-5/8
1-1/4
(32)
6
3-5/8
1
Heavy Duty
Fasteners
DS
(27)
6
0.177
(4.5)
3-5/8
1-1/4
(32)
6
Number of
Fasteners
1
Shear
lb (kN)
225
(1.00)
450
(2.00)
225
(1.00)
450
(2.00)
275
(1.22)
275
(1.22)
620
(2.76)
240
(1.07)
410
(1.82)
240
(1.07)
480
(2.14)
350
2
1
2
(1.56)
350
(1.56)
1 Allowable loads were developed from testing the low-velocity fasteners with 16 gauge (Fy 33 ksi) steel track. A safety factor greater than or equal to 5.0 was
used in accordance with ICC-ES AC70. Steel track members not meeting the specification noted must be investigated in accordance with accepted design
criteria.
2 Allowable values are for fasteners installed in concrete having the designated compressive strength at the time of installation.
3 Spacing and edge distance constraints are as noted in Figure 1-4 at the top of this page.
4 Allowable shear load values are for loads applied perpendicular to the edge of the concrete.
5 Multiple fasteners are recommended for any attachment.
6 Minimum edge distance of 2-1/4" cannot be decreased. Closer edge distances can result in edge breakout failure of the base material during installation.
As a result, fasteners are offset from the center line of the track.
7 SSMA track designation for 3-5/8" track is 362T 150-54 and for 6" track is 600T 150-54.
38 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Fastener
Universal
Knurled Shank
Fasteners
Shank Diameter
in. (mm)
0.157
(4.0)
X-U
Heavy Duty
Fasteners
Fastener Length
in. (mm)
0.177
(4.5)
DS
(27)
1-1/4
(32)
1-1/2
(37)
(27)
1-1/4
(32)
1-1/2
(37)
Track
Width in.7
3-5/8
6
3-5/8
6
3-5/8
6
3-5/8
6
3-5/8
6
3-5/8
6
Number of
Fasteners
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
Shear
lb (kN)
260 (1.16)
490 (2.18)
260 (1.16)
520 (2.31)
350 (1.56)
465 (2.07)
350 (1.56)
720 (3.20)
295 (1.31)
465 (2.07)
295 (1.31)
755 (3.36)
205 (0.91)
395 (1.76)
205 (0.91)
720 (3.20)
225 (1.00)
370 (1.65)
225 (1.00)
595 (2.65)
215 (0.96)
370 (1.65)
215 (0.96)
590 (2.62)
1 Allowable loads were developed from testing the low-velocity fasteners with 16 gauge (Fy 33 ksi) steel track. A safety factor greater than or equal to
5.0 was used in accordance with ICC-ES AC70. Steel members not meeting the specification noted must be investigated in accordance with accepted
design criteria.
2 Allowable values are for fasteners installed in concrete having the designated compressive strength at the time of installation.
3 Spacing and edge distance constraints are as noted in Figures 1-4 at the top of the previous page.
4 Allowable shear load values are for loads applied perpendicular to the edge of the concrete.
5 Multiple fasteners are recommended for any attachment.
6 Minimum edge distance of 2-1/4" cannot be decreased. Closer edge distances can result in edge breakout failure of the base material during installation. As a
result, fasteners are offset from the center line of the track.
7 SSMA track designation for 3-5/8" track is 362T 150-54 and for 6" track is 600T 150-54.
1/2"
1"
1/2"1/2"
1"
Figure 5:
3-5/8" or 6" Track 1 Fastener
1/2"
Figure 6:
3-5/8" or 6" Track 2 Fasteners
Allowable Shear Loads for Attachment of Perimeter Track to Minimum ASTM A36 (Fy 36 ksi; Fu 58 ksi) Steel, lb (kN)1,2,3,4
Fastener
Description
Universal
Knurled Shank
Fasteners
Heavy Duty
Fasteners
Fastener
Shank
Diameter
in. (mm)
X-U
0.157
(4.0)
X-U 15
0.145
(3.7)
EDS
0.177
(4.5)
Number of
Fasteners
1
2
1
2
1
2
(3.20)
(6.40)
(1.76)
(3.56)
(2.96)
(5.92)
1/4
720
1440
395
790
935
1870
3/8
(3.20)
(6.40)
(1.76)
(3.51)
(4.16)
(8.32)
720
1440
450
900
970
1940
1/2
(3.20)
(6.40)
(2.00)
(4.00)
(4.31)
(8.62)
720
1440
5006
10006
995
1990
3/45
(3.20)
(6.40)
(2.22)
(4.45)
(4.43)
(8.86)
375
750
4006
8006
655
1310
(1.67)
(3.34)
(1.78)
(3.56)
(2.91)
(5.82)
1 The tabulated allowable load values are for the low-velocity fasteners only, using a safety factor that is greater than or equal to 5.0, calculated in accordance with
ICC-ES AC70. Steel members connected to the substrate must be investigated in accordance with accepted design criteria.
2 Low-velocity fasteners shall be driven to where the point of the fastener penetrates the steel base material, except as noted.
3 Multiple fasteners are recommended for increased reliability.
4 The minimum edge distance for fastening into steel is 1/2". Minimum spacing for fastening into steel without reduction in performance is 1".
5 Unless otherwise noted, tabulated allowable load values provided for 3/4" steel are based upon minimum point penetration of 1/2". If 1/2" point penetration is not
achieved, but a point penetration of at least 3/8" is obtained, the tabulated shear load should be reduced by 8 percent.
6 Based upon minimum point penetration of 15/32".
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 39
Figure 7:
Normal Weight Concrete
Figure 8:
Lightweight Concrete with Pour Stop
Allowable Loads for Attachment of Cold-Formed Steel Deflection Slip Clips with X-U Universal
Powder-Actuated Fasteners 3,4,5,6,7,8,9
Clip Type
Fastener
Number of
Fasteners
2
Verticlip SLB600
(14 GA.)
X-U 27
3
4
2
WSC 950
(16 GA.)
X-U 27
3
4
WSC 1500
(12 GA.)
X-U 27
FCSC
(14 GA.)
X-U 27
2
3
2
3
Normal Weight
Concrete
Allowable Load 1
lb (kN)
Lightweight Concrete
with Pour Stop
Allowable Load 2
lb (kN)
160
(0.71)
245
(1.09)
330
(1.47)
125
(0.56)
145
(0.64)
220
(0.98)
90
(0.40)
185
(0.82)
140
(0.62)
290
(1.29)
160
(0.71)
245
(1.09)
380
(1.69)
155
(0.69)
275
(1.22)
275
(1.22)
130
(0.58)
235
(1.05)
170
(0.76)
320
(1.42)
Location of
Fasteners
1 Allowable load based on a safety factor of 5.0 in direction shown in Figure 7 above for attachment of deflection slip clip to 4000 psi Normal Weight Concrete Slab.
2 Allowable load based on a safety factor of 5.0 in direction shown in Figure 8 above for attachment of deflection slip clip to 3000 psi Lightweight Concrete Slab with
12 GA. sheet steel pour stop with minimum yield strength (Fy) of 33 ksi.
3 Testing based on deflection slip clips obtained in February 2007. Subsequent changes by the manufacturer to the deflection slip clip design may affect load values.
4 Allowable load values are for fasteners installed in concrete having the designated compressive strength at the time of installation.
5 Allowable load values are based off of the fixtures tested. Other members connected to the deflection slip clips must be investigated in accordance with accepted
design criteria.
6 Spacing of fasteners are subsequent to the design of each deflection slip clip and the location of any pre-drilled holes.
7 For edge distance and base material thickness requirements, reference Section 3.2.1.1.4.
8 Allowable values are for loads applied perpendicular to the edge of the concrete.
9 Multiple fasteners are recommended for any attachment.
40 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Figure 9: Steel
Allowable Loads for Attachment of Cold-Formed Steel Deflection Slip Clips with X-U Universal Powder-Actuated
Fasteners to Minimum ASTM A36 (Fy 36 ksi; Fu 58 ksi) Steel 1,2,3,4,5,6,7,8
Clip Type
Fastener
Verticlip SLB600
(14 GA.)
X-U 16
X-U 19
EDS 19
EDS 22
Number of
Fasteners
3
4
2
3
4
2
X-U 16
X-U 19
EDS 19
EDS 22
WSC 1500
(12 GA.)
3
4
2
X-U 16
X-U 19
EDS 19
EDS 22
FCSC
(14 GA.)
Location of
Fasteners
740
(3.29)
1490
(6.63)
2115
(9.41)
510
(2.27)
610
(2.71)
870
(3.87)
970
(4.31)
1105
(4.92)
1300
(5.78)
715
(3.18)
940
(4.18)
1055
(4.69)
X-U 16
X-U 19
EDS 19
EDS 22
WSC 950
(16 GA.)
Allowable Load
lb (kN)
3
4
1 Allowable load based on a variable safety factor in accordance with Section F of AISI S100.
2 Testing based on deflection slip clips developed in February 2007. Subsequent changes by the deflection slip clip manufacturer to the clip design may affect
load values.
3 Allowable load values are based off of the connections tested. Steel members connected to the deflection slip clips must be investigated in accordance with
accepted design criteria.
4 Spacing of the fasteners depends on the specific deflection slip clip and location of pre-drilled holes in the deflection slip clip.
5 For edge distance and base material thickness requirements reference Section 3.2.1.2.2.
6 Allowable load values are for loads applied perpendicular to the edge of the base steel member.
7 Multiple fasteners are recommended for any attachment.
8 Allowable load values are based off of testing into 1/4" ASTM A36 structural steel.
Shank Length
in. (mm)
Shank
in. (mm)
Washer
Packaging Qty
X-U 16 P8TH
X-U 19 P8TH
X-U 27 P8TH
X-U 32
X-U 15
EDS 19 P10
EDS 22 P10
DS 27 P10
DS 32 P10
5/8 (16)
3/4 (19)
1 (27)
1-1/4 (32)
5/8 (16)
3/4 (19)
7/8 (22)
1 (27)
1-1/4 (32)
0.157 (4.0)
0.157 (4.0)
0.157 (4.0)
0.157 (4.0)
0.145 (3.7)
0.177 (4.0)
0.177 (4.0)
0.177 (4.0)
0.177 (4.0)
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 41
Product Description
3.2.5.2
Material Specifications
3.2.5.3
3.2.5.4
Technical
3.2.5.5
Installation Instructions
3.2.5.6
Ordering Information
Approvals/Listings
ICC-ES (International Code Council)
ESR-3059
COLA (City of Los Angeles)
RR 25921
Figure 3: Typical Shear Wall Assembly with Cold-Formed Steel Framing and
Structural Wood Panel Sheathing Attached with Hilti X-GPN 37 MX Fasteners
42 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
X-GPN 37 MX
Fastener
Material
Carbon Steel
Fastener
Plating
5 m Zinc1
Structural
Wood Panels
Base
Material
Exposure 1, Structural 1
Plywood Complying with
27-68 mils
DOC PS-1 or
(0.0283-0.0713 inch)
Oriented Strand Board
ASTM A1003 or
(OSB) Complying with DOC ASTM A653 CFS Member
PS-2 for Exposure 1
1 ASTM B633, SC1, Type III. Refer to Section 2.3.3.1 for more information.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 43
44 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Figure 8: First Cycle Envelope Curve from Cyclic / Simulated Seismic Load Test
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 45
An extensive ICC-ES AC230 independent laboratory test program was conducted to confirm the static and cyclic / simulated seismic performance of shear wall assemblies composed of
CFS framing and wood structural panel sheathing attached with
Hilti X-GPN 37 MX power-driven fasteners. The program test
scope consisted of static and cyclic / simulated seismic fullscale shear wall assembly tests, as well as comparative small
element lateral strength (shear) tests and transverse strength
(pullout and pull-through) tests conducted as discussed in
Gauge
68
0.0713
(1.811)
14
54
0.0566
(1.438)
16
43
0.0451
(1.146)
18
33
0.0346
(0.879)
20
27
0.0283
(0.719)
22
1 Minimum Thickness represents 95% of the design thickness and is the minimum acceptable thickness delivered to the jobsite.
2 Steel thickness equivalents are taken from Steel Stud Manufacturers Association (SSMA) Product Technical Information.
Table 2 - Allowable Transverse Loads for Connections of Structural Wood Panels to CFS Framing Using
Hilti X-GPN 37 MX Power-Driven Fasteners, lb (N)3,4,5,6,7
Nominal Panel
Thickness,
in. (mm)
Pull-Through
Capacity1,6
Pullout Capacity2
CFS Framing Thickness Designation, Mils (gauge)
27
(22)
33
(20)
43
(18)
54
(16)
68
(14)
3/8
(9.5)
57 (253)
17
(75)
21
(93)
55
(245)
93
(414)
93
(414)
15/32
(12)
87 (387)
21
(93)
21
(93)
55
(245)
112
(498)
112
(498)
19/32
(15)
87 (387)
21
(93)
21
(93)
55
(245)
112
(498)
112
(498)
1 The safety factor for pull-through capacity is 5.0 in accordance with ICC-ES AC230.
2 Safety factors for pullout capacity determined in accordance with AISI S100.
3 The lower of allowable pull-through capacity and pullout capacity must be used for design.
4 Panel thicknesses shown are minimums. Thicker panels, up to 3/4" (19 mm) thick, may be used.
5 Allowable transverse loads are based on a minimum panel edge distance of 3/8" (9.5 mm).
6 The tabulated values are for plywood. For connections of OSB having thicknesses equal to or greater than to those noted in the table, the allowable pull-through
capacity is equal to the applicable value from the table multiplied by 0.915.
7 Multiple fasteners are recommended for any attachment.
Table 3 - Allowable Lateral Loads for Connections of Structural Wood Panels to CFS Framing Using
Hilti X-GPN 37 MX Power-Driven Fasteners, lb (N)1,2,3,4,5
Nominal Panel
Thickness,
in. (mm)
3/8 (9.5)
15/32
19/32
33 (20)
43
(18)
54
(16)
68
(14)
(689)
(302)
88 (391)
128
(569)
128
(569)
155
(12)
68
(302)
88 (391)
138
(614)
155
(689)
155
(689)
(15)
68
(302)
88 (391)
150
(667)
193
(859)
193
(859)
46 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Wood Structural
Panel Thickness,
in. (mm)7,8
Maximum Stud
Spacing,
in. (mm)
24
3/8 (9.5)
33 (20)
15/32 (12)
3/8 (9.5)
43 (18)
15/32 (12)
3/8 (9.5)
54 (16)
15/32 (12)
(152)
(102)
(76)
(51)
395
540
650
765
(610)
(58)
(79)
(95)
(112)
16
475
655
805
1000
(146)
(406)
(69)
(96)
(117)
24
395
540
650
765
(610)
(58)
(79)
(95)
(112)
16
475
655
805
1000
(146)
(406)
(69)
(96)
(117)
24
395
540
650
765
(610)
(58)
(79)
(95)
(112)
16
475
655
805
1000
(406)
(69)
(96)
(117)
(146)
24
400
545
655
775
(610)
(58)
(80)
(96)
(113)
16
475
665
815
1010
(406)
(69)
(97)
(119)
(147)
24
435
600
720
850
(610)
(63)
(88)
(105)
(124)
16
525
725
890
1105
(406)
(77)
(106)
(130)
(161)
24
485
660
795
935
(610)
(71)
(96)
(116)
(136)
1225
16
580
805
985
(406)
(85)
(117)
(144)
(179)
24
610
830
1000
1180
(610)
(89)
(121)
(146)
(172)
16
730
1010
1240
1540
(406)
(107)
(147)
(181)
(225)
24
710
975
1170
1380
(610)
(104)
(142)
(171)
(201)
16
850
1185
1450
1800
(406)
(124)
(173)
(212)
(263)
24
835
1140
1370
1615
(610)
(122)
(166)
(200)
(236)
16
995
1385
1700
2110
(406)
(145)
(202)
(248)
(308)
1 For Allowable Stress Design (ASD), the nominal shear resistance values listed in this table should be divided by a safety factor of 2.0 for wind loads and 2.5
for seismic loads per AISI S213.
2 For Load and Resistance Factor Design (LRFD), the nominal shear resistance values listed in this table must be multiplied by a resistance factor of 0.60 for
seismic loads and 0.65 for wind loads. For Limit States Design (LSD), the nominal shear resistance values listed in this table must be multiplied by a resistance
factor of 0.70 for seismic and wind loads per AISI S213.
3 Tabulated values are applicable for seismic and wind loads. For other in-plane lateral loads of normal or permanent load duration as defined in AF&PA NDS, the
values in the table must be multiplied by 0.63 (normal) or 0.56 (permanent).
4 The minimum distance from the fastener to the wood structural panel edge must be 3/8" (9.5 mm).
5 Fastener spacing must be a maximum of 12" (294 mm) on center in the field of the wood structural panel.
6 Hold-downs, end posts and sill fasteners must be designed to resist the required lateral loads.
7 Panel thicknesses shown are minimums. Thicker panels, up to 3/4" (19 mm) thick, may be used.
8 Tabulated values are for plywood panels. For shear wall assemblies constructed with OSB having thicknesses equal to or greater than those noted in the table,
the nominal shear resistance is equal to the applicable value in the table multiplied by 0.915.
9 Tabulated design data for use in all Seismic Design Categories A-F.
10 Type I shear wall assemblies are limited to a height-width aspect ratio of 2:1.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 47
For SI:
Variables and constants in the equations are as defined in Section C2.1.1 of AISI S213. Values for G*tsheathing are typically taken from
IBC Table 2305.2(2).
Shank Length
in. (mm)
Shank
in. (mm)
Guidance
Washer
Packaging
Quantity
X-GPN 37 MX
1-1/2 (37)
0.102 (2.60)
8 mm
750
Description
Package Content
X-GPN 37 MX
Includes tool, detachable leg support, tool support, fastener pouch set, ear protectors, safety
glasses, cleaning cloth and operating instructions in an impact-resistant plastic tool box
Hilti GC-22
Gas Canister
for GX 120
48 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
3.2.6.1
Product Description
Product Features:
Powder-actuated fasteners:
Shank diameters* of 0.138", 0.145"
or 0.157" are available providing a
variety of solutions depending on
application requirements.
3.2.6.3
Technical Data
3.2.6.4
Ordering Information
Gas-actuated fasteners:
Shank diameter of 0.118" provides
ease of penetration in concrete
and steel.
Listings/Approvals
ICC-ES (International Code Council)
ESR-2269 (X-U and X-U 15)
ESR-1752 (X-GN, X-EGN, X-GHP, X-S13,
X-S16, X-C 22 P8TH and X-C 20 THP)
ESR-1663 (X-C, X-C 22 P8TH and
X-C 20 THP)
COLA (City of Los Angeles)
RR 25675 (X-U and X-U 15)
RR 25662 (X-GN, X-EGN, X-GHP, X-S13,
X-S16, X-C 22 P8TH and X-C 20 THP)
RR 25646 (X-C, X-C 22 P8TH and
X-C 20 THP)
Fastener
Material
Fastener
Plating
Base
Material
Powder-Actuated
or Gas-Actuated
X-S13 THP
X-S16 P8TH
X-U 15
X-C
X-EGN
X-GN
Carbon Steel
Carbon Steel
Carbon Steel
Carbon Steel
Carbon Steel
Carbon Steel
5 m Zinc1
5 m Zinc1
5 m Zinc1
5 m Zinc1
2-10 m Zinc
5 m Zinc1
Powder-Actuated
Powder-Actuated
Powder-Actuated
Powder-Actuated
Gas-Actuated
Gas-Actuated
X-GHP
Carbon Steel
2-10 m Zinc
Steel
Steel
Steel
Concrete or Masonry
Steel
Concrete or Masonry
High-Strength Concrete
or Steel
Gas-Actuated
1 ASTM B633, SC 1, Type III. Refer to Section 2.3.3.1 for more information.
* X-U Universal Powder-Actuated fasteners with 0.157" shank diameter are also available for drywall track fastening and are discussed in more detail in Sections
3.2.3 and 3.2.4.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 49
Fastener
Drywall
Track Fastener
X-C 22 P8TH
Drywall Track
Gas Fastener
X-GN
Drywall Track
Gas Fastener
X-GHP
Shank
Minimum
Diameter* Embedment
in. (mm)
in. (mm)
0.138
(3.5)
0.118
(3.0)
0.118
(3.0)
2000 psi
Tension
Shear
lb (kN)
lb (kN)
3/4
(19)
55
(0.24)
130
(0.58)
90
(0.40)
170
(0.76)
3/4
1
(19)
(25)
95
115
(0.42)
(0.51)
120
220
(0.53)
(0.98)
95
115
(0.42)
(0.51)
120
220
(0.53)
(0.98)
5/8
(16)
50
(0.22)
120
(0.53)
50
(0.22)
90
(0.40)
1 The tabulated allowable load values are for the low-velocity fasteners only, using a safety factor that is greater than or equal to 5.0, calculated in accordance with
ICC-ES AC70. Wood or steel members connected to the substrate must be investigated in accordance with accepted design criteria.
2 Multiple fasteners are recommended for any attachment.
Fastener
Drywall Track
Fastener
X-C 20 THP
Drywall Track
Fastener
X-C 22 P8TH
Drywall Track
Gas Fastener
X-GN
Drywall Track
Gas Fastener
X-GHP
Shank
Minimum
Diameter* Embedment
in. (mm)
in. (mm)
0.138
(3.5)
0.138
(3.5)
0.118
(3.0)
0.118
(3.0)
Shear
lb (kN)
Fastener Location
Installed Through 3" Deep Metal Deck
into Concrete2,3
Tension lb (kN)
Shear
lb (kN)
Upper Flute
Lower Flute
5/8
(16)
55
(0.24)
110
(0.49)
55
(0.24)
110
(0.49)
3/4
(19)
110
(0.49)
220
(0.98)
120
(0.53)
60
(0.27)
260
(1.16)
3/4
1
(19)
(25)
115
170
(0.51)
(0.76)
140
220
(0.62)
(0.98)
75
155
(0.33)
(0.69)
85
160
(0.38)
(0.71)
175
255
(0.78)
(1.13)
5/8
(16)
60
(0.27)
140
(0.62)
60
(0.27)
60
(0.27)
175
(0.78)
1 The tabulated allowable load values are for the low-velocity fasteners only, using a safety factor that is greater than or equal to 5.0, calculated in accordance with
ICC-ES AC70. Wood or steel members connected to the substrate must be investigated in accordance with accepted design criteria.
2 The steel deck profile is 3" deep composite floor deck with a thickness of 20 gauge (0.0358"). Figure 1 (Section 3.2.1.1.6) shows the nominal flute dimensions,
fastener locations, and load orientations for the deck profile.
3 Structural lightweight concrete fill above top of metal deck shall be a minimum of 3-1/4" deep.
4 Multiple fasteners are recommended for any attachment.
Allowable Loads In Minimum fc = 3000 psi Structural Lightweight Concrete Over 1-1/2" Deep, B-Type Steel Deck1,4
Description
Drywall Track
Fastener
Drywall Track
Gas Fastener
Drywall Track
Gas Fastener
Shank
Diameter*
in. (mm)
0.138
X-C 22 P8TH
(3.5)
0.118
X-GN
(3.0)
0.118
X-GHP
(3.0)
Fastener
Minimum
Embedment
in. (mm)
Fastener Location
Installed Through 1-1/2" Deep Metal Deck into Concrete2,3
Tension lb (kN)
Shear
lb (kN)
Upper Flute
Lower Flute
3/4
(19)
90
(0.40)
110
(0.49)
295
(1.31)
3/4
1
(19)
(25)
75
155
(0.33)
(0.69)
85
160
(0.38)
(0.71)
175
255
(0.78)
(1.13)
5/8
(16)
60
(0.27)
60
(0.27)
175
(0.78)
1 The tabulated allowable load values are for the low-velocity fasteners only, using a safety factor that is greater than or equal to 5.0, calculated in accordance with
ICC-ES AC70. Wood or steel members connected to the substrate must be investigated in accordance with accepted design criteria.
2 Steel deck profiles are 1-1/2" deep, B-type deck with a thickness of 20 gauge (0.0358"). Fasteners may be installed through the metal deck into lightweight
concrete having both nominal and inverted deck profile orientations with a minimum lower flute width of 1-3/4" or 3-1/2", respectively. Fasteners shall be placed
at centerline of deck flutes. Refer to Figures 2 and 3 (Section 3.2.1.1.6) for additional flute dimensions, fastener locations, and load orientations for both
deck orientations.
3 Structural lightweight concrete fill above top of metal deck shall be a minimum 2-1/2" deep.
4 Multiple fasteners are recommended for any attachment.
* X-U Universal Powder-Actuated fasteners with 0.157" shank diameter are also available for drywall track fastening and are discussed in more detail in Sections
3.2.3 and 3.2.4.
50 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Shank
Min.
Fastener
Diameter* Embed.
in. (mm) in. (mm)
3/4
0.118
(19)
X-GN
(3.0)
1
(25)
0.118
5/8
X-GHP
(3.0)
(16)
Hollow CMU
Mortar Joint6
Face Shell6
Face Shell6
Mortar Joint6
Tension Shear Tension Shear7 Tension Shear Tension Shear7 Tension Shear9
lb (kN) lb (kN) lb (kN) lb (kN) lb (kN) lb (kN) lb (kN) lb (kN) lb (kN) lb (kN)
90
115
65
55
95
120
70
85
65
90
(0.40)
(0.51)
(0.29)
(0.24)
(0.42)
(0.53)
(0.31)
(0.38)
(0.29)
(0.40)
115
130
70
65
130
140
85
120
75
95
(0.51)
(0.58)
(0.31)
(0.29)
(0.58)
(0.62)
(0.38)
(0.53)
(0.33)
(0.42)
40
80
15
40
90
100
40
80
60
85
(0.18)
(0.36)
(0.07)
(0.18)
(0.40)
(0.44)
(0.18)
(0.36)
(0.27)
(0.38)
The tabulated allowable load values are for the low-velocity fastener only,
using a safety factor of 5.0 or higher calculated in accordance with
ICC-ES AC70. Wood or steel members connected to the substrate must
be investigated in accordance with accepted design criteria.
2 The tabulated allowable load values are for low-velocity fasteners installed
in normal weight or lightweight concrete masonry units conforming to
ASTM C90.
3 The tabulated allowable load values are for low-velocity fasteners installed
in concrete masonry units with mortar conforming to ASTM C270, Type N.
4 The tabulated allowable load values are for low-velocity fasteners installed
in concrete masonry units with grout conforming to ASTM C476, as
coarse grout.
5 The tabulated allowable load values are for one low-velocity fastener
installed in an individual masonry unit cell and at least 4" from the edge of
the wall.
6 Fastener can be located anywhere on the face shell as shown in the figure
to the right.
7 Shear direction can be horizontal or vertical (Bed Joint or T-Joint) along
the CMU wall plane.
8 Fastener located in center of grouted cell installed vertically.
9 Shear can be in any direction.
10 Multiple fasteners are recommended for any attachment.
#FE+PJOU
5+PJOU
$PODSFUF
.BTPOSZ
6OJU
$.6
Fastener
X-S13
X-S16 P8TH
X-U 15
X-EGN4
X-EGN3,4
X-GHP
Shank
Diameter*
in. (mm)
0.145
(3.7)
0.145
(3.7)
0.145
(3.7)
0.118
(3.0)
0.118
(3.0)
0.118
(3.0)
1/8
3/16
1/2
3/4
Tension Shear Tension Shear Tension Shear Tension Shear Tension Shear Tension Shear
lb (kN) lb (kN) lb (kN) lb (kN) lb (kN) lb (kN) lb (kN) lb (kN) lb (kN) lb (kN) lb (kN) lb (kN)
(1.11)
155
(0.69)
140 230 220
(0.62) (1.02) (0.98)
220
(0.98)
125 230 170
(0.56) (1.02) (0.76)
450
(2.00)
530
(2.36)
395
(1.76)
245
(1.09)
295
(1.31)
245
(1.09)
300
(1.33)
330
(1.47)
230
(1.02)
225
(1.00)
260
(1.16)
200
(0.89)
450
(2.00)
575
(2.56)
395
(1.76)
290
(1.29)
355
(1.58)
230
(1.02)
300
(1.33)
335
(1.49)
420
(1.87)
280
(1.25)
280
(1.25)
250
(1.11)
450
(2.00)
610
(2.71)
450
(2.00)
330
(1.47)
385
(1.71)
255
(1.13)
265
(1.18)
3655
(1.62)
280
(1.25)
280
(1.25)
480
(2.14)
5005
(2.22)
330
(1.47)
385
(1.71)
365
(1.62)
280
(1.25)
280
(1.25)
4005
(1.78)
330
(1.47)
385
(1.71)
1 The tabulated allowable load values are for the low-velocity fasteners only, using a safety factor that is greater than or equal to 5.0, calculated in accordance
with ICC-ES AC70. Wood or steel members connected to the substrate must be in investigated in accordance with accepted design criteria.
2 Low-velocity fasteners shall be driven to where the point of the fastener penetrates the steel base material in accordance with Section 3.2.1.2.3, except as noted
in this table.
3 Based on testing with Fy = 50 ksi base material.
4 X-EGN fasteners installed into 3/8" or thicker base steel require 0.320" minimum penetration depth.
5 Based upon minimum point penetration of 15/32".
6 Multiple fasteners are recommended for any attachment.
7 Refer to guidelines for fastening to steel, Section 3.2.1.2, for application limits.
* X-U Universal Powder-Actuated fasteners with 0.157" shank diameter are also available for drywall track fastening and are discussed in more detail in Sections
3.2.3 and 3.2.4.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 51
Fastener
X-GN, X-EGN,
X-GHP
X-C 20 THP
X-S13 THP
X-S16 P8TH
X-U 15 P8TH
Head
Dia.
in.
(mm)
0.276
(7.0)
0.322
(8.2)
0.322
(8.2)
0.322
(8.2)
14 ga.
16 ga.
24 ga.
25/26 ga.
Tension Shear Tension Shear Tension Shear Tension Shear Tension Shear Tension Shear Tension Shear
lb (kN) lb (kN) lb (kN) lb (kN) lb (kN) lb (kN) lb (kN) lb (kN) lb (kN) lb (kN) lb (kN) lb (kN) lb (kN) lb (kN)
860
(3.83)
985
(4.38)
685
(3.05)
685
(3.05)
940
(4.18)
715
(3.18)
720
(3.20)
940
(4.18)
325
(1.45)
490
(2.18)
490
(2.18)
785
(3.49)
390
(1.73)
465
(2.07)
515
(2.29)
685
(3.05)
265
(1.18)
360
(1.60)
360
(1.60)
625
(2.78)
335
(1.49)
375
(1.67)
440
(1.96)
550
(2.45)
250
(1.11)
300
(1.33)
300
(1.33)
510
(2.27)
235
(1.05)
265
(1.18)
310
(1.38)
465
(2.07)
170
(0.76)
205
(0.91)
205
(0.91)
390
(1.73)
185
(0.82)
200
(0.89)
235
(1.05)
365
(1.62)
100
(0.44)
120
(0.53)
120
(0.53)
335
(1.49)
125
(0.56)
130
(0.58)
145
(0.64)
315
(1.40)
1 Allowable load values are based on a safety factor of 3.0 in accordance with the AISI S100.
2 Allowable pullover capacities of sheet steel should be compared to the allowable fastener tensile load capacities in concrete, steel, and masonry to
determine controlling resistance load.
3 Allowable shear bearing capacities of sheet steel should be compared to allowable fastener shear capacities in concrete, steel or masonry to determine
controlling resistance load.
4 Data is based on the following minimum sheet steel properties, Fy = 33 ksi, Fu = 45 ksi (ASTM A653 material).
Shank Length
in. (mm)
Shank *
in. (mm)
Washer
Packaging Qty
X-C 20 THP
X-C 22 TH
X-C 20 MX
3/4 (20)
7/8 (22)
3/4 (20)
0.138 (3.5)
0.138 (3.5)
0.138 (3.5)
8 mm plastic tophat
8 mm metal tophat
Collated
1000 pcs/box
1000 pcs/box
1000 pcs/box
Powder-Actuated (Steel)
Fastener
Description
Shank Length
in. (mm)
Shank *
in. (mm)
Washer
Packaging Qty
X-S13 THP
X-S13 MX
X-S16 TH
X-U 15 TH
X-U 15 MX
1/2 (13)
1/2 (13)
5/8 (16)
5/8 (16)
5/8 (16)
0.145 (3.7)
0.145 (3.7)
0.145 (3.7)
0.145 (3.7)
0.145 (3.7)
8 mm plastic tophat
Collated
8 mm metal tophat
8 mm metal tophat
Collated
Gas-Actuated (Concrete)
Fastener
Description
Shank Length
in. (mm)
Shank
in. (mm)
Washer
Packaging Qty
X-GN 20 MX
X-GN 27 MX
X-GN 32 MX
X-GN 39 MX
X-GHP 18 MX
X-GHP 20 MX
3/4 (20)
1 (27)
1-1/4 (32)
1-5/8 (39)
11/16 (18)
3/4 (20)
0.118 (3.0)
0.118 (3.0)
0.118 (3.0)
0.118 (3.0)
0.118 (3.0)
0.118 (3.0)
Collated
Collated
Collated
Collated
Collated
Collated
750 pcs/box
750 pcs/box
750 pcs/box
750 pcs/box
750 pcs/box
750 pcs/box
Fastener
Description
Shank Length
in. (mm)
Shank
in. (mm)
Washer
Packaging Qty
X-EGN 14 MX (steel)
X-GHP 18 MX
X-GHP 20 MX
1/2 (14)
11/16 (18)
3/4 (20)
0.118 (3.0)
0.118 (3.0)
0.118 (3.0)
Collated
Collated
Collated
750 pcs/box
750 pcs/box
750 pcs/box
Gas-Actuated (Steel)
* X-U Universal Powder-Actuated fasteners with 0.157" shank diameter are also available for drywall track fastening and are discussed in more detail in Sections
3.2.3 and 3.2.4.
52 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Product Features:
Fasteners for use with chemical
pressure treated lumber (X-CP).
3.2.7.1
Product Description
3.2.7.2
Material Specifications
3.2.7.3
Technical Data
3.2.7.4
Ordering Information
X-CF
X-CP
Listings/Approvals
ICC-ES (International Code Council)
ESR-2379
COLA (City of Los Angeles)
RR 25708
Installed X-CP
fastener with
A 153" clearly
marked on washer.
Fastener
Material
Washer
Material
Fastener
Plating
X-CF 72 P8 S23
Carbon Steel
Carbon Steel
5 m Zinc1
Carbon Steel
X-CP 72 P8 S23
Carbon Steel
Washer
Plating
5 m Zinc1
2
1 ASTM B633, SC 1, Type III. Refer to Section 2.3.3.1 for more information.
2 Equivalent in corrosion resistance to ASTM A153 HDG. Refer to Section 2.3.3.1 for more information.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 53
Environment
Indoor - Dry:
Untreated Lumber
with no moisture exposure
Wood Type
Untreated Lumber
Fastener
X-CF washer
Washer
Designation
Inspection
1 If the moisture content of Pressure-Treated Lumber is high (> 18 %) or unknown, stainless steel fasteners are recommended. Select appropriate stainless steel
grade for your application.
2 Guidelines based on fastener coating / material resistance to environmental corrosion (commonly called rusting"). Evaluate site conditions which may affect
these guidelines, such as: corrosive agents other than those listed; expected service life; other (non environmental) types of corrosion etc.
3 In highly corrosive environments (such as direct exposure to chlorides with average temperatures above 86 F (30 C)) it is generally recommended that a Highly
Corrosive Resistant (HCR) Fastener be used such as Hilti HAS HCR Adhesive Anchor Rods. Contact Hilti Technical Support for more information.
Shank Diameter
Washer Diameter
Fastener Length
in. (mm)
in. (mm)
in. (mm)
Interior Shear Wall or Interior Non-Shear Wall4
X-CF 72 P8 S23
X-CP 72 P8 S23
0.145
0.145
(3.7)
(3.7)
X-CF 72 P8 S23
X-CP 72 P8 S23
0.145
0.145
(3.7)
(3.7)
0.905 (23)
2-7/8
0.905 (23)
2-7/8
Exterior Shear Wall5
0.905 (23)
2-7/8
0.905 (23)
2-7/8
Tension
lb (kN)
Shear
lb (kN)
(72)
(72)
130
175
(0.58)
(0.78)
210
250
(0.93)
(1.11)
(72)
(72)
130
165
(0.58)
(0.73)
165
95
(0.73)
(0.42)
1 The tabulated allowable load values are for the low-velocity fasteners only, using a safety factor greater than or equal to 5.0, calculated in accordance with
ICC-ES AC70. Wood sill plates connected to the substrate must be investigated in accordance with accepted design criteria.
2 Multiple fasteners are recommended for any attachment.
3 Allowable load values are for attachment of nominal 2x lumber with the steel washer bearing on the top surface of the wood.
4 These allowable load values based on testing performed at a minimum 2-3/4" edge distance (i.e. middle of slab).
5 These allowable load values based on testing performed at 1-3/4" edge distance.
Shank Length
in. (mm)
Shank
in. (mm)
Washer
in. (mm)
Packaging Qty
X-CF 72 P8 S23
2-7/8 (72)
0.145 (3.7)
0.905 (23)
X-CP 72 P8 S23
2-7/8 (72)
0.145 (3.7)
0.905 (23)
54 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
3.2.8.1
Product Description
Technical Data
3.2.8.4
Installation Instructions
3.2.8.5
Ordering Information
Fastener
Material
Carbon Steel
Carbon Steel
Fastener
Plating
5 m Zinc1
5 m Zinc1
1 ASTM B633, SC1, Type III. Refer to Section 2.3.3.1 for more information.
X-W6
Thread Designation
X-W6-11-22
X-W6-11-27
X-W6-20-22
X-W6-20-27
X-W6-38-27
W10-30-27
W10-30-32
W10-30-42
UNC 1/4-inch
UNC 1/4-inch
UNC 1/4-inch
UNC 1/4-inch
UNC 1/4-inch
UNC 3/8-inch
UNC 3/8-inch
UNC 3/8-inch
Thread
Length
Thread Length
in.
(mm)
(11)
7/16
(11)
7/16
(20)
3/4
(20)
3/4
(38)
1-1/2
1-3/16 (30)
1-3/16 (30)
1-3/16 (30)
Shank Length
in.
(mm)
(22)
7/8
1
(27)
(22)
7/8
1
(27)
1
(27)
1
(27)
(32)
1-1/4
(42)
1-5/8
W10
Listings/Approvals
ICC-ES (International Code Council)
ESR-1663
COLA (City of Los Angeles)
RR 25646
FM (Factory Mutual)
W10-30-27P10, W10-30-32P10 and
W10-30-42P10 Fasteners for Sprinkler
Pipe Hangers
UL (Underwriters Laboratories)
W10-30-32P10 and W10-30-42P10,
Fasteners for Sprinkler Pipe Hangers Up to 2-1/2" diameter pipe
Shank
Length
Fastener
X-W6
W10
Shank
Diameter
Minimum
Embedment
in. (mm)
0.145
(3.7)
in.
3/4
1
1
1-1/4
1-5/8
0.205
(5.2)
(mm)
(19)
(25)
(25)
(32)
(41)
1 The tabulated allowable load values are for the low-velocity fasteners only, using a safety factor that is greater than or equal to 5.0, calculated in accordance with
ICC-ES AC70. Wood or steel members connected to the substrate must be investigated in accordance with accepted design criteria.
2 Multiple fasteners are recommended for any attachment.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 55
Fastener
1/420
Threaded Stud
X-W6
3/816
Threaded Stud
W10
Shank
Dia.
in. (mm)
0.145
(3.7)
0.205
(5.2)
Min.
Embed.
in.
3/4
1
1
1-1/4
1-5/8
(mm)
(20)
(25)
(25)
(32)
(41)
Shear
lb
(kN)
185 (0.82)
185 (0.82)
190 (0.85)
380 (1.69)
540 (2.40)
Fastener Location
Installed Through 3" Deep
Metal Deck into Concrete2,3
Tension lb (kN)
Shear
Upper Flute
Lower Flute
lb
(kN)
125 (0.56)
115 (0.54)
185 (0.82)
160 (0.71)
180 (0.80)
185 (0.82)
160 (0.71)
185 (0.82)
160 (0.71)
210 (0.93)
470 (2.09)
435 (1.93)
325 (1.45)
675 (3.00)
1 The tabulated allowable load values are for the low-velocity fasteners only, using a safety factor that is greater than or equal to 5.0, calculated in accordance with
ICC-ES AC70. Wood or steel members connected to the substrate must be investigated in accordance with accepted design criteria.
2 The steel deck profile is 3" deep composite floor deck with a thickness of 20 gauge (0.0358"). Figure 1 (Section 3.2.1.1.6) shows the nominal flute dimensions,
fastener locations and load orientations for the deck profile.
3 Structural lightweight concrete fill above top of metal deck shall be a minimum of 3-1/4" deep.
4 Multiple fasteners are recommended for any attachment.
Fastener
X-W6
Shank
Diameter
in. (mm)
0.145
Hollow CMU
Grout Filled CMU
Face Shell6
Mortar Joint6
Face Shell6
Mortar Joint6
Minimum
7
Embedment Tension Shear Tension Shear Tension Shear Tension Shear7
lb (kN) lb (kN) lb (kN) lb (kN) lb (kN) lb (kN) lb (kN) lb (kN)
in. (mm)
1
105
175
80
110
125
175
135
150
(3.7)
(25)
(0.47)
The tabulated allowable load values are for the low-velocity fastener only,
using a safety factor of 5.0 or higher. Wood or steel members connected
to the substrate must be investigated in accordance with accepted design
criteria.
The tabulated allowable load values are for low-velocity fasteners installed
in normal weight or lightweight concrete masonry units conforming to
ASTM C90.
The tabulated allowable load values are for low-velocity fasteners installed
in concrete masonry units with mortar conforming to ASTM C270, Type N.
The tabulated allowable load values are for low-velocity fasteners installed
in concrete masonry units with grout conforming to ASTM C476, as
coarse grout.
The tabulated allowable load values are for one low-velocity fastener
installed in an individual masonry unit cell and at least 4" from the edge
of the wall.
(0.78)
(0.36)
(0.49)
(0.56)
#FE+PJOU
$PODSFUF
.BTPOSZ
(0.78)
(0.60)
(0.67)
5+PJOU
6OJU
$.6
X-W6
3.6
(4.9)
W10
10.0
(13.6)
56 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Tmax
* These are abbreviated instructions which may vary by application. ALWAYS review/follow the instructions accompanying the product.
W10
3.0 (4.0)
4.5 (6.0)
Shank Length
in. (mm)
Shank
in. (mm)
X-W6-11-22 FP8
7/8 (22)
1 (27)
0.145 (3.7)
7/16 (11)
UNC 1/4-inch
8 mm plastic
100 pcs
0.145 (3.7)
7/16 (11)
UNC 1/4-inch
8 mm plastic
100 pcs
7/8 (22)
1 (27)
0.145 (3.7)
3/4 (20)
UNC 1/4-inch
8 mm plastic
100 pcs
X-W6-20-27 FP8
0.145 (3.7)
3/4 (20)
UNC 1/4-inch
8 mm plastic
100 pcs
X-W6-38-27 FP8
1 (27)
0.145 (3.7)
1-1/2 (38)
UNC 1/4-inch
8 mm plastic
100 pcs
X-W6-11-27 FP8
X-W6-20-22 FP8
Thread Length
in. (mm)
Thread
Guidance
Washer
Packaging
Quantity
W10-30-27 P10
1 (27)
0.205 (5.2)
1-3/16 (30)
UNC 3/8-inch
10 mm plastic
100 pcs
W10-30-32 P10
1-1/4 (32)
0.205 (5.2)
1-3/16 (30)
UNC 3/8-inch
10 mm plastic
100 pcs
W10-30-42 P10
1-5/8 (42)
0.205 (5.2)
1-3/16 (30)
UNC 3/8-inch
10 mm plastic
100 pcs
X-W6
W10*
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 57
Product Description
3.2.9.2
Material Specifications
3.2.9.3
Technical Data
3.2.9.4
Installation Instructions
3.2.9.5
Ordering Information
X-CRM8
X-BT W6*
X-BT W10*
X-BT M8*
Listings/Approvals
ICC-ES (International Code Council)
ESR-2347
COLA (City of Los Angeles)
RR 25684
FM (Factory Mutual)
X-EW10H and X-EW6H
UL (Underwriters Laboratories)
X-EW10H and X-EW6H
ABS (American Bureau of Shipping)
Lloyds Register
GL (Germanischer Lloyd)
DNV
Fastener
Designation
X-EW6H
X-EW10H
X-CRM8
X-BT W6*
X-BT W10*
X-BT M8*
Fastener
Plating
5 m Zinc1
5 m Zinc1
N/A
N/A
N/A
N/A
1 ASTM B633, SC 1, Type III. Refer to Section 2.3.3.1 for more information.
2 Equivalent corrosion resistance to SAE 316 stainless steel. Refer to Section 2.3.3.1 for more information.
Thread
Designation
X-EW6H-11-9
UNC 1/4-inch
Thread
Length
in.
(mm)
7/16 (11)
X-EW6H-20-9
UNC 1/4-inch
3/4
(20)
Shank
Length
in.
(mm)
(9)
3/8
3/8
(9)
X-EW6H-28-9
UNC 1/4-inch
1-1/8
(28)
3/8
(9)
X-EW6H-38-9
UNC 1/4-inch
1-1/2
(38)
3/8
(9)
9/16
(14)
1/2
(12)
1/2
(12)
(24)
1/4
(6)
X-BT M8-15-6*
(15)
1/4
(6)
X-BT W10-24-6*
(24)
1/4
(6)
X-EW10H-30-14
X-CRM8-9-12
X-CRM8-15-12
X-BT W6-24-6*
Thread
Length
Fastener
Material
Carbon Steel
Carbon Steel
SAE 316 Stainless Steel2
SAE 316 Stainless Steel2
SAE 316 Stainless Steel2
SAE 316 Stainless Steel2
hNVS
Shank
Length
Thread and
Shank Length
Threaded Stud
Stand-off (hNVS)
* Innovative blunt-tip X-BT fasteners are discussed in more detail in Section 3.2.10
58 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Shank
Diameter
in. (mm)
Stud Type
3/16 (4.8)
Tension
Shear
lb (kN)
lb (kN)
1/4 (6.4)
Tension
Shear
lb (kN)
lb (kN)
3/8 (9.5)
Tension
Shear
lb (kN)
lb (kN)
1/2 (12.7)
Tension
Shear
lb (kN)
lb (kN)
3/4 (19.1)
Tension
Shear
lb (kN)
lb (kN)
360
500
500
600
500
600
500
600
500
600
(1.60)
(2.22)
(2.22)
(2.67)
(2.22)
(2.67)
(2.22)
(2.67)
(2.22)
(2.67)
(5.2)
0.157
(4.0)
0.177
(4.5)
X-EW6H
0.145
(3.7)
X-EW10H
0.205
X-CRM8
X-BT3
W6/W10/M8
970
1000
1100
1100
1100
1100
800
800
(4.31)
(4.45)
(4.89)
(4.89)
(4.89)
(4.89)
(3.56)
(3.56)
405
405
405
405
(1.80)
(1.80)
(1.80)
(1.80)
185
270
295
425
405
585
405
585
405
585
(0.82)
(1.20)
(1.31)
(1.89)
(1.80)
(2.60)
(1.80)
(2.60)
(1.80)
(2.60)
1 The tabulated allowable load values are for the low-velocity threaded studs only, using a factor of safety that is greater than or equal to 5.0, calculated in
accordance with AC70. Wood or steel members connected to the substrate must be investigated in accordance with accepted design criteria.
2 Tabulated allowable load values based upon embedment in steel such that threaded stud stand-off, hNVS, complies with the Threaded Steel Stud
Specification Table.
3 To prevent through penetration or damage to coatings on the base steel, a minimum base steel thickness of 5/16" is required for X-BT threaded studs. Load
values provided for 3/8" base steel thickness are also valid for 5/16" base steel thickness. For further information, reference Section 3.2.10.
X-EW6H
2.2
(3.0)
X-EW10H
6.5
(8.8)
X-CRM8
4.0
(5.5)
X-BT W6/W10/M8
6.0
(8.2)
Tmax
hNVS
1 These are abbreviated instructions which may vary by application. ALWAYS review/follow the instructions accompanying the product.
2 Installation instructions for innovative blunt-tip X-BT fasteners are provided in Section 3.2.10.4
Maximum Tightening Torque, Tmax, for Threaded Studs Driven into Steel, ft-lb (Nm)
Stud Type
X-EW6H
3.0
(4.1)
X-EW10H
11.0
(14.9)
X-CRM8
6.0
(8.1)
X-BT*
W6, W10 and M8
6.0
(8.1)
*Innovative blunt-tip X-BT fasteners are installed with a Hilti DX 351 BT powder-actuated tool and discussed in more detail in Section 3.2.10.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 59
Shank Length
in. (mm)
3/8 (9)
3/8 (9)
3/8 (9)
3/8 (9)
9/16 (14)
1/4 (6)
1/4 (6)
1/4 (6)
12 (12)
12 (12)
12 (12)
12 (12)
Shank
in. (mm)
0.145 (3.7)
0.145 (3.7)
0.145 (3.7)
0.145 (3.7)
0.205 (5.2)
0.177 (4.5)
0.177 (4.5)
0.177 (4.5)
0.157 (4.0)
0.157 (4.0)
0.157 (4.0)
0.157 (4.0)
Thread Length
in. (mm)
1-1/2 (38)
1-1/8 (28)
3/4 (20)
7/16 (11)
1-3/16 (30)
15/16 (24)
15/16 (24)
5/8 (15)
5/8 (15)
5/8 (15)
3/8 (9)
3/8 (9)
Thread
UNC 1/4-inch
UNC 1/4-inch
UNC 1/4-inch
UNC 1/4-inch
UNC 3/8-inch
UNC 1/4-inch
UNC 3/8-inch
Metric 8 mm
Metric 8 mm
Metric 8 mm
Metric 8 mm
Metric 8 mm
Guidance
Washer
8 mm plastic
Packaging
Quantity
100 pcs
8 mm plastic
8 mm plastic
8 mm plastic
10 mm plastic
12 mm steel
12 mm steel
12 mm steel
8 mm plastic
10 mm plastic
8 mm plastic
10 mm plastic
100 pcs
100 pcs
100 pcs
100 pcs
100 pcs
100 pcs
100 pcs
100 pcs
100 pcs
100 pcs
100 pcs
X-CRM8
DX 460 Tool
X-BT*
* Innovative blunt-tip X-BT fasteners are discussed in more detail in Section 3.2.10
60 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Listings/Approvals
6/$
<>
<>
X-BT W6-24-6
SN12-R
0.472"
0.177"
[4.5]
[ 12]
X-BT W10-24-6
SN12-R
0.551"
[14]
UNC
3/8"
0.839"
[21.3]
0.945" [24]
Tensile
Strength, Fu
ksi (N/mm2)
1.232" [31.3]
Material Designation
<>
Part
<>
M8
0.472"
0.177"
[4.5]
[ 12]
X-BT M8-15-6
SN12-R
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 61
Load Type
Tension, lb (kN)
Shear, lb (kN)
Moment, ft-lb (Nm)
Torque, ft-lb (Nm)
Detailing:
Spacing: 5/8" (15 mm)
Edge Distance: 1/4" (6 mm)
Minimum
Grade 50 steels
515 (2.3)
765 (3.4)
6 (8.1)
6 (8.1)
1/4"
5/8"
5/8"
5/16"
1 The tabulated allowable load values are for the X-BT fastener only, using a safety factor of 5.0.
Wood or steel members connected to the substrate must be investigated in accordance with
accepted design criterion.
2 Minimum edge distance and minimum spacing are 1/4" and 5/8", respectively.
3 Multiple fasteners are recommended for any attachment.
1/4"
Configuration
Maximum
Copper or
Aluminum
Wire
Single Point3,4
8 AWG
(10 mm2)
Double Point4
6 AWG
(16 mm2)
Single Point3
10 AWG
(6 mm2)
Double Point4
6 AWG
(16 mm2)
X-BT W6 SN12-R
Minimum Base
Steel Thickness
in. (mm)
5/16
(8)
Grounding
Connectors
Ring
Terminated
Copper or
Aluminum
Conductors
1 Additional information for installation of X-BT when used as a grounding stud can be found on
page 64.
2 Selection, design and evaluation of the electrical wire and connectors for the given grounding
application and intended use is the responsibility of the electrical engineer.
3 Maximum copper or aluminum wire size based upon the results of testing according to UL 467.
4 Maximum copper wire size based upon the results of testing according to IEC 60947-7-2
1/4
1.055 ( 26.8)
3/8
1.055 ( 26.8)
M8
0.661 ( 16.8)
hNVS
in. (mm)
0.059"
hNVS2
NN
<>
D1
I /74
Designation
ca. 1.5 mm
62 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
4. Install material to be
fastened, washer
and nut
Installation Details
hNVS
X-BT M8
hNVS
Before fastener
installation:
2 NO
debris
NO
water,
oil, etc.
Tightening torque,
Tmax = 6 ft-lb (8 Nm)
Hilti Tool
SFH 18-A
SF 18-A
SFH 144-A
SF 144-A
Torque
Setting1
9-10
9-10
9-10
9-10
Tmax
* These are abbreviated instructions which may vary by application. ALWAYS review/follow the instructions accompanying the product.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 63
2
3
5
Slotted T-bar
Crimp T-bar
2. Insert cable into Crimp T-bar and wrap Crimp T-bar around cable.
1 These are abbreviated instructions which may vary by application. ALWAYS review/follow the instructions accompanying the product.
2 Reference Section 3.2.10.5 for information on number and size of cables.
3 Space T-bars at approximately 24" to 32" (60-80 cm.). Adjust as necessary to control cable sagging.
64 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
M8
W6
W10
5/8 (15)
15/16 (24)
15/16 (24)
100
100
100
Box includes: 100 studs, 1 power regulation guide, 1 coating protector, 1 TX-BT step drill bit
* X-BT stainless steel threaded studs also available without sealing washer on request by special order
3-1/8 (80)
4-5/16 (110)
Package Ordering
Contents Designation
10
10
Cartridges
(in magazine strips of 10)
Color
Code
Brown
Package Ordering
Contents Designation
100
Tool Sets
For Use
with
W6 and W10
M8
Package Ordering
Contents Designation
1
1
X-BT Set
X-BTG Set
Set includes: 1 DX 351 BT or BTG powder-actuated tool, 1 BT cleaning kit, 1 XBT 4000-A cordless drill, 1 charger, 2 batteries, 1 information sheet, 1 spray lube, 3 operating instructions, packed complete in a Hilti toolbox.
Individual Tools
For Use
with
Package Ordering
Contents Designation
W6 and W10
M8
X-BT
Supplied in an impact-resistant plastic toolbox with cleaning kit, ear protectors, safety goggles, Hilti spray
lubricant and operating instructions, info sheet.
Supplied in an impact-resistant plastic toolbox with cleaning kit, ear protectors, safety goggles, Hilti spray
lubricant and operating instructions, info sheet.
Supplied in a cardboard box with operating instructions. Battery and charger sold separately.
Recommended Max.
No. of Cables
Cable
Slotted T-bars
T-bar X-P15002-ESL-2
T-bar X-P15002-ESL-3
T-bar X-P15002-ESL-4
T-bar X-P15002-ESL-6
T-bar X-P15002-ESL-8
2
3
4
6
8
Up to 1.25"
Up to 1.25"
Up to 1.25"
Up to 1.25"
Up to 1.25"
1
1
1
1
2
2
0.437" to 0.750"
0.680" to 0.900"
0.750" to 1.000"
0.375" to 0.531"
0.437" to 0.750"
0.680" to 0.900"
Crimp T-bars
T-bar X-1026-1
T-bar X-1027-1
T-bar X-1030-1
T-bar X-1040-1
T-bar X-2002-2
T-bar X-2003-2
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 65
Listings/Approvals
ICC-ES (International Code Council)
ESR-2795 (X-HS)
COLA (City of Los Angeles)
RR 25826 (X-HS)
FM (Factory Mutual)
W10-30-27P10, W10-30-32P10 and
W10-30-42P10 fasteners for sprinkler
pipe hangers in concrete
EW10-30-15P10, X-EW10H, X-EW6H
and X-HS U19 fasteners for sprinkler
pipe hangers in steel
UL (Underwriters Laboratories)
X-ECH, X-EKB and X-ECT hangers
for wire positioning devices
W10-30-32P10, W10-30-42P10,
EW10-30-15P10, X-EW10H and X-EW6H
fasteners for sprinkler pipe hangers
Cable and Conduit Hardware Hangers
X-HS W6, X-HS W10 and X-RH
X-EMTSC MX Stand-Off
Conduit Clip
66 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Clip/Hanger
Designation
X-HS W10/W6
X-HS W6 MX
X-ECH
X-RH
X-EKB MX
X-ECT MX
X-BX/EMTC
X-BX/EMTC MX
X-EMTSC MX
1
Powder-Actuated
Fastener Plating1
5 m Zinc
5 m Zinc2
5 m Zinc
5 m Zinc
5 m Zinc2
5 m Zinc2
5 m Zinc
5 m Zinc2
5 m Zinc2
Clip/Hanger
Material
Carbon Steel
Carbon Steel
Nylon Plastic
Carbon Steel
Plastic
Plastic
Carbon Steel
Carbon Steel
Carbon Steel
Clip/Hanger
Plating1
5 m Zinc
5 m Zinc
N/A
5 m Zinc
N/A
N/A
5 m Zinc
5 m Zinc
5 m Zinc
The 5 m coating is in accordance with ASTM B633, SC1, Type III. Reference Section 2.3.3.1 for more information.
2 Noted clips/hangers do not come with a pre-mounted powder-actuated fastener. Material and plating information provided for the powder-actuated fasteners
commonly used with these clips.
Description
Fastener
X-HS U321
X-HS U222
X-RH 1/4 U272
in.
0.157
0.157
0.157
(mm)
(4.0)
(4.0)
(4.0)
50 (0.22)
1 The tabulated allowable load values are for the low-velocity fasteners only, using a safety factor that is greater than or equal to 5.0, calculated in accordance with
ICC-ES AC70.
2 The tabulated allowable load values for X-RH and X-HS U22 are per UL 2239 with a minimum embedment of 3/4" for X-RH.
3 Multiple fasteners are recommended for any attachment. Threaded or smooth rod must be investigated in accordance with accepted design criteria.
Fastener
Shank
Diameter
Installed into
Concrete
Tension Shear
X-HS U32
0.157
(4.0)
Fastener Location
Installed Through 3" Deep Metal Deck
into Concrete2
Upper Flute
Lower Flute
4545454545Tension Shear
Tension Shear
Tension Shear
Tension Shear
Degree
Degree
Degree
Degree
Degree
95
115
1056
(0.42) (0.51) (0.47)
125
220
1756
(0.56) (0.98) (0.78)
95
220
1356
(0.42) (0.98) (0.60)
95
220
1356
(0.42) (0.98) (0.60)
95
220
1356
(0.42) (0.98) (0.60)
1 The tabulated allowable load values are for the X-HS threaded rod hanger assembly with an X-U fastener only, using a safety factor that is greater than or equal
to 5.0, calculated in accordance with ICC-ES AC70. Threaded rod must be investigated in accordance with accepted design criteria.
2 The steel deck profile for the 3" deep composite floor deck has a minimum thickness of 20 gauge (0.0358") and a minimum Fy of 33 ksi. Lower and upper flute
width must be a minimum of 4-1/2". Figure 1 in Section 3.2.1.1.6 shows the nominal flute dimensions, fastener locations and load orientations for the deck
profile. Structural lightweight concrete fill above top of steel deck must be minimum 3-1/4".
3 The steel deck profile for the 1-1/2" deep composite floor deck has a minimum thickness of 20 gauge (0.0358") and a minimum Fy of 33 ksi. Lower flute and
upper flute widths must be a minimum of 1-3/4" and 3-1/2", respectively. This deck may also be inverted as shown in Figure 3 in Section 3.2.1.1.6. Figures 2
and 3 in Section 3.2.1.1.6 show the nominal flute dimensions, fastener locations and load orientations for the deck profile. Structural lightweight concrete fill
above top of steel deck must be minimum 2-1/2".
4 Nailhead Standoff, hNVS, must be less than or equal to 3/8" for the X-HS U32 hanger assembly. Reference Section 3.2.11.4.
5 Allowable loads apply to X-HS threaded rod hanger assemblies with either the 1/4" or 3/8" diameter internally threaded hole.
6 Allowable loads for 45-degree applications are based on testing. For allowable loads at other angles of installation, refer to Section 3.2.1.1.8.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 67
Fastener
Description
Fastener
Shank
Diameter
in. (mm)
Threaded Rod
Hanger with premounted fastener
X-HS U19
0.157
(4.0)
0.157
(4.0)
(4.0)
3/16 (4.8)
1/4 (6.4)
Tension
lb (kN)
Shear
lb (kN)
Shear
lb (kN)
270
220
275
270
220
275
270
220
275
(1.20)
(0.98)
(1.22)
(1.20)
(0.98)
(1.22)
(1.20)
(0.98)
50
45-Degree Tension
lb (kN)
lb (kN)
50
(0.22)
3/8 (9.5)
45-Degree Tension
lb (kN)
lb (kN)
Shear
lb (kN)
1/2 (12.7)
45-Degree Tension
lb (kN)
lb (kN)
Shear
lb (kN)
45-Degree
lb (kN)
270
220
275
(1.22)
(1.20)
(0.98)
(1.22)
1 The tabulated allowable load values are for the low-velocity fasteners only, using a safety factor that is greater than or equal to 5.0, calculated in accordance
with ICC-ES AC70. Threaded rod must be investigated in accordance with accepted design criteria.
2 The tabulated allowable load values for the X-RH are per UL 2239.
3 Low-velocity fasteners shall be driven to where the point of the fastener penetrates the steel base material in accordance with Section 3.2.1.2.3.
4 Multiple fasteners are recommended for any attachment. Reference Section 3.2.11.4 for installation instructions for X-HS.
5 Allowable loads for 45-degree applications are based on testing. For allowable loads at other angles of installation, refer to Section 3.2.1.2.8.
Fastener
Size
Small
Medium
Large
X-ECT MX
Tensile
Tensile
lb (kN)
lb (kN)
15 (0.07)
10 (0.04)
Nrec
X-EKB 4 MX
Allowable Load Nrec
Nrec
Tensile
Tensile
lb (kN)
lb (kN)
5 (0.02)
10 (0.04)
Nrec
Tensile
Nrec
X-EMTSC 1/2" MX
X-EMTSC 1" MX
Allowable Load Nrec
X-EKB 8 MX
Allowable Load Nrec
Tensile
lb (kN)
lb (kN)
10 (0.04)
15 (0.07)
X-EKB 16 MX
Allowable Load Nrec
Nrec
Nrec
Nrec
Nrec
Tensile
lb (kN)
15 (0.07)
1 The allowable load capacities are based on tests with X-GHP 20, X-GN 27 and X-EGN 14 using a safety factor that is greater than or equal to 5.0.
2 Load capacites are based on armored cable and EMT.
3 X-GHP 20 must be installed at a minimum penetration depth of 9/16" into concrete. X-GN 27 must be installed at a minimum penetration depth of 3/4" into CMU
or mortar joint. X-EGN 14 must be installed at a minimum penetration depth of 0.320" through or into steel. Hanger assemblies must be firmly clamped to the
base material.
4 Concrete base materials include 2000 to 6000 psi normal weight or lightweight types and also includes attachment through steel deck into concrete.
5 Steel base materials include 1/8" or thicker carbon steel base material with minimum yield strengths (Fy) of 36 ksi.
6 CMU base materials include hollow or grout-filled concrete masonry units conforming to ASTM C90.
68 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
hNVS
1. Insert appropriate
sized threaded rod
into hanger.
3. Ensure proper
fastener embedment.
hNVS 3/8" (9.5 mm)
* These are abbreviated instructions which may vary by application. ALWAYS review/follow the instructions accompanying the product.
Fastener Length
in. (mm)
Fastener Shank
in. (mm)
Thread Rod
0.157 (4.0)
0.157 (4.0)
0.157 (4.0)
0.157 (4.0)
UNC 1/4-inch
UNC 3/8-inch
UNC 1/4-inch
UNC 3/8-inch
0.157 (4.0)
0.157 (4.0)
UNC 3/8-inch
UNC 1/4-inch
N/A
UNC 1/4-inch
Shank Length
in. (mm)
Fastener Shank
in. (mm)
Thread Length
in. (mm)
Thread
7/8 (22)
1 (27)
7/8 (22)
1 (27)
1 (27)
1 (27)
1-1/4 (32)
1-5/8 (42)
0.145 (3.7)
0.145 (3.7)
0.145 (3.7)
0.145 (3.7)
0.145 (3.7)
0.205 (5.2)
0.205 (5.2)
0.205 (5.2)
1/2 (11)
1/2 (11)
3/4 (20)
3/4 (20)
1-1/2 (38)
1-3/16 (30)
1-3/16 (30)
1-3/16 (30)
UNC 1/4-inch
UNC 1/4-inch
UNC 1/4-inch
UNC 1/4-inch
UNC 1/4-inch
UNC 3/8-inch
UNC 3/8-inch
UNC 3/8-inch
3/8 (9)
3/8 (9)
3/8 (9)
3/8 (9)
9/16 (14)
0.145 (3.7)
0.145 (3.7)
0.145 (3.7)
0.145 (3.7)
0.205 (5.2)
1/2 (11)
3/4 (20)
1-1/8 (28)
1-1/2 (38)
1-3/16 (30)
UNC 1/4-inch
UNC 1/4-inch
UNC 1/4-inch
UNC 1/4-inch
UNC 3/8-inch
Fastener
Description
Overall Length
in. (mm)
Thread
Stud
Thread
Rod
Coupler 1/4-20
Coupler 3/8-16
Adapter B-1/4x3/8
1 (25)
1-1/8 (28)
7/8 (22)
UNC 1/4-inch
UNC 3/8-inch
UNC 1/4-inch
UNC 1/4-inch
UNC 3/8-inch
UNC 3/8-inch
Concrete
X-HS W6 U32 P8S15
1-1/4 (32)
X-HS W10 U32 P8S15
1-1/4 (32)
X-HS W6 U22 P8S15
7/8 (22)
X-HS W10 U22 P8S15
7/8 (22)
Steel
X-HS W10 U19 P8S15
5/8 (16)
X-HS W6 U19 P8S15
5/8 (16)
MX Version (without pre-mounted fastener)
X-HS W6 MX
N/A
Threaded Studs
Fastener
Description
Concrete and Masonry
X-W6-11-22 FP8
X-W6-11-27 FP8
X-W6-20-22 FP8
X-W6-20-27 FP8
X-W6-38-27 FP8
W10-30-27 P10
W10-30-32 P10
W10-30-42 P10
Steel
X-EW6H-11-9 FP8
X-EW6H-20-9 FP8
X-EW6H-28-9 FP8
X-EW6H-38-9 FP8
X-EW10H-30-14 P10
Couplers
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 69
Fastener Length
in. (mm)
Fastener Shank
in. (mm)
Rod
Concrete
X-RH 1/4 U27
1 (27)
0.157 (4.0)
1/4-inch
Fastener Length
in. (mm)
Fastener Shank
in. (mm)
Number of
1/4" cables
N/A
N/A
N/A
N/A
N/A
N/A
15-22
30-37
45-52
1-1/2 (37)
1-1/2 (37)
1-1/2 (37)
0.157 (4.0)
0.157 (4.0)
0.157 (4.0)
15-22
30-37
45-52
X-RH
X-ECH
Max Diameter of
Cable in. (mm)
Maximum No.
of Cables
X-EKB 4 MX
X-EKB 8 MX
X-EKB 16 MX
1/4 (6)
1/4 (6)
1/4 (6)
4
8
16
X-EKB MX
X-ECT MX
1/2 (12)
Fastener Length
in. (mm)
Fastener Shank
in. (mm)
Conduit
in. (mm)
7/8 (22)
7/8 (22)
7/8 (22)
7/8 (22)
0.157 (4.0)
0.157 (4.0)
0.157 (4.0)
0.157 (4.0)
3/8 (10)
1/2 (13)
3/4 (19)
1 (25)
1 (27)
1 (27)
1 (27)
1 (27)
0.138 (3.5)
0.138 (3.5)
0.138 (3.5)
0.138 (3.5)
3/8 (10)
1/2 (13)
3/4 (19)
1 (25)
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
3/8 (10)
1/2 (13)
3/4 (19)
1 (25)
X-ECT
without Cable Tie
X-EMTC
X-BX/EMTC MX
Conduit
1/2 (13)
3/4 (19)
1 (25)
X-EMTSC MX
70 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Powder-Actuated
Fastener Material
Carbon Steel
Carbon Steel
X-IE
Washer
Material2
Plastic
Plastic
Powder-Actuated
Fastener Plating1
5 m Zinc
5 m Zinc
X-SW
1 ASTM B633, SC1, Type III. Reference Section 2.3.3.1 for more information.
2 Due to potential embrittlement degradation of fastener plastic, exposure to UV light should be limited to
less than 90 days.
(0.15)
45
(0.20)
55
(0.25)
65
2-3/4 (70)
Shear lb (kN)
65
(0.30)
(0.30)
135
(0.60)
135
(0.60)
135
(0.60)
135
(0.60)
55
(0.25)
60
(0.27)
65
(0.30)
65
(0.30)
65
(0.30)
65
(0.30)
(40)
1-3/4
(45)
(50)
2-3/8
(60)
(75)
3-1/8
(80)
(100)
4-3/4
(120)
75
(0.33)
80
(0.35)
80
(0.35)
80
(0.35)
(0.60)
135
(0.60)
135
(0.60)
135
(0.60)
65
(0.30)
65
(0.30)
65
(0.30)
65
(0.30)
65
(0.30)
(0.30)
65
(0.30)
65
(0.30)
65
(0.30)
65
(0.30)
65
Tension
lb
(kN)
65
(0.30)
lb
65
Shear
(kN)
(0.30)
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2015 71
Correct:
Top hat crushed
4. Verify successful fastening. Remove
if not clamped tight to insulation.
Inorrect:
Top hat not crushed
* These are abbreviated instructions which may vary by application. ALWAYS review/follow the instructions accompanying the product.
Shank Length
in. (mm)
Shank
in. (mm)
Insulation Material
Thickness in. (mm)
Washer
Color
Quantity
1-7/8 (47)
1-7/8 (47)
2 (52)
2 (52)
2 (52)
2 (52)
2 (52)
2 (52)
2 (52)
2-7/8 (72)
0.177 (4.5)
0.177 (4.5)
0.177 (4.5)
0.177 (4.5)
0.177 (4.5)
0.177 (4.5)
0.177 (4.5)
0.177 (4.5)
0.177 (4.5)
0.177 (4.5)
1 (25)
1-1/2 (38)
1-5/8 (42)
2 (51)
2-1/2 (64)
2-3/4 (70)
3 (76)
3-1/4 (83)
4 (102)
4-3/4 (120)
White
White
White
White
White
White
White
White
White
White
300 pcs
300 pcs
300 pcs
300 pcs
300 pcs
200 pcs
200 pcs
200 pcs
200 pcs
150 pcs
Description
Shank Length
in. (mm)
Shank
in. (mm)
Washer
in. (mm)
Washer
Color
Quantity
X-SW 30 C-37
X-SW 30 C-37
X-SW 30 C-37
X-SW 30 C-62
X-SW 60 C-37
X-SW 60 C-47
X-SW 60 C-62
1-1/2 (37)
1-1/2 (37)
1-1/2 (37)
2-1/2 (62)
1-1/2 (37)
1-7/8 (47)
2-1/2 (62)
0.138 (3.5)
0.138 (3.5)
0.138 (3.5)
0.138 (3.5)
0.138 (3.5)
0.138 (3.5)
0.138 (3.5)
1-3/16 (30)
1-3/16 (30)
1-3/16 (30)
1-3/16 (30)
2-3/8 (60)
2-3/8 (60)
2-3/8 (60)
Gray
Gray
White
Gray
Gray
Gray
Gray
150 pcs
500 pcs
100 pcs
100 pcs
150 pcs
100 pcs
100 pcs
X-SW
72 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
The innovative X-CW ceiling wire assembly contains a powderactuated fastener and integrated steel wire with clamping
washer which eliminates the need for wire wrapping. The
X-CW fastening system is installed with Hilti DX-351-CT
Powder-Actuated Tool and adjusted for the height of the
ceiling system. The X-CC ceiling clip assemblies consist of a
sheet steel clip with a pre-mounted powder-actuated fastener
and may be ordered with or without pre-tied 12 gauge wires
of different lengths. The eye-lag ceiling fastening system is an
efficient solution for supporting direct or indirect hung lay-in
panel suspended ceiling systems from wood and steel deck
base materials.
X-CC
Eye-Lag Screw
Applicable Base
Material
Concrete,
Lightweight Concrete
over Metal Deck
Concrete,
Lightweight Concrete
over Metal Deck,
Steel
Wood, Sheet Steel
Fastener Types
Recommended
Installation Tools
Wire Type
Section
X-C27, X-C32,
X-U22, X-U27
DX 351-CT
with Pole Tool
Integrated
12 Gauge Wire1
3.3.2
X-C27, X-C32,
X-U22, X-U27,
X-AL-H22, X-AL-H27
DX 351
with Pole Tool
3.3.3
EL WS, EL S, EL SD
Telescopic Screw
Ceiling Tool
Provided by others
3.3.4
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 73
Hilti Ceiling
Attachment System
Support Clip
for Main Runners
Wall Moulding
Carrying Channel
Acoustical Tile
Cross Runners
Spline
(Spanning
Cross Runners)
12 ga.
wire typ.
Hilti Ceiling
Attachment System
Main Runners
3 tight turns
in 1-1/2"
Acoustical
Lay-in Panels
Cross Runners
(Spanning
Main Runners)
Wall Moulding
Main Runners
74 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
12"
min. 3-1/4"
3"
4-1/2" min.
Form Deck
Lower Flute Location
Upper Flute Location
Direction
of combined 1-1/8"
load on
Min. Edge
fastener
Distance
(Typical)
Direction
of tension
load on
fastener
(Typical)
4-1/2" min.
7-1/4" min.
Figure 3: Hilti Ceiling Fastening System Location in 3-in.-Deep Composite Floor Deck, Normal Deck Profile Orientation
min. 2-1/2"
1-3/4"
Form Deck
Upper Flute Location
Lower Flute Location
Direction
of combined
load on
fastener
(Typical)
Direction
of tension
7/8"
load on
Min. Edge fastener
Distance (Typical)
1-1/2"
2-1/2"
3-1/2"
Figure 4: Hilti Ceiling Fastening System Location in 1-1/2-in.-Deep Composite Floor Deck, Normal Deck Profile Orientation
Form Deck
Upper Flute Location
Lower Flute Location
Direction
of combined
load on
fastener
(Typical)
Direction
1-3/4" of tension
Min. Edge load on
Distance fastener
(Typical)
min. 2-1/2"
1-3/4"
1-1/2"
3-1/2"
Figure 5: Hilti Ceiling Fastening System Location in 1-1/2-in.-Deep Composite Floor Deck, Inverted Deck Profile Orientation
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 75
Product Description
3.3.2.2
Material Specifications
3.3.2.3
Technical Data
3.3.2.4
Installation Instructions
3.3.2.5
Ordering Information
Fastener
Fastener
Powder
Actuate
Fastener
Material
Powder
Actuated
Fastener
Plating5
Steel
Clamping
Washer
Material
Steel
Clamping
Washer
Plating5
Ceiling Wire
Material
Ceiling
Wire
Plating5
X-CW Class 1
Carbon Steel
5 m Zinc1
Carbon Steel
5 m Zinc2
Carbon Steel
12 m Zinc3
X-CW INT
Carbon Steel
5 m Zinc1
Carbon Steel
5 m Zinc2
Carbon Steel
Zinc4
Allowable Loads for Hilti X-CW Ceiling Wire Assemblies Installed in Normal
Weight Concrete, lb (kN)1,2,3,4
Concrete Compressive Strength
Ceiling Wire Type
Pre-mounted X-U
or X-C fastener
(X-U Shown)
Pre-mounted
Ceiling Wire
Hanger
4000 psi
6000 psi
Tension
45-Degree
Tension
X-CW C27
210 (0.93)
210 (0.93)
45 Degree
X-CW C32
210 (0.93)
210 (0.93)
X-CW U22
100 (0.44)
90 (0.40)
X-CW U27
210 (0.93)
210 (0.93)
130 (0.58)
150 (0.67)
1 The tabulated allowable loads apply to the X-CW ceiling wire assembly using a minimum safety factor of
5.0 in accordance with ICC-ES AC70 if controlled by powder-actuated fastener pullout or a minimum of
2.0 in accordance with ICC-ES AC368 if controlled by wire yielding and fracture.
2 Allowable values are for fasteners installed in concrete having the designated compressive strength at
the time of installation.
3 Concrete thickness at the point of penetration must be a minimum of the fastener embedment depth
plus 1-1/2".
4 Multiple fasteners must be used for suspended ceiling applications.
Allowable Loads for Hilti X-CW Ceiling Wire Assemblies Installed in Structural
Lightweight Concrete over Composite Floor Deck, lb (kN)1,2,3,4
3000 psi Concrete Compressive Strength
Pre-mounted
steel clamping
washer
Upper flute
Lower flute
Tension
45-Degree
Tension
45 Degree
110 (0.49)
150 (0.67)
170 (0.76)
210 (0.93)
210 (0.93)
210 (0.93)
100 (0.44)
100 (0.44)
150 (0.67)
145 (0.64)
145 (0.64)
160 (0.71)
1 The tabulated allowable loads apply to the X-CW ceiling wire assembly using a minimum safety factor of
5.0 in accordance with ICC-ES AC70 if controlled by powder-actuated fastener pullout or a minimum of
2.0 in accordance with ICC-ES AC368 if controlled by wire yielding and fracture.
2 Allowable values are for fasteners installed in concrete having the designated compressive strength at
the time of installation.
3 Testing completed in composite floor deck having a minimum thickness of 20 gauge (0.0358") and a
minimum yield strength (Fy) of 38 ksi. Figures 3-5 (Section 3.3.1.3) show nominal flute dimensions,
fastener locations and load orientations for the deck profile. Concrete thickness at the point of
penetration must be a minimum of the fastener embedment depth plus 1-1/2".
4 Multiple fasteners must be used for suspended ceiling applications.
76 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
* These are abbreviated instructions which may vary by application. ALWAYS review/follow the instructions accompanying the product.
Shank
in. (mm)
Fastener Length
in. (mm)
Packaging
Quantity1
0.138 (3.5)
0.157 (4.0)
0.157 (4.0)
1 (27)
7/8 (22)
1 (27)
1000
1000
1000
0.138 (3.5)
0.138 (3.5)
0.157 (4.0)
0.157 (4.0)
1 (27)
1-1/4 (32)
7/8 (22)
1 (27)
1000
1000
1000
1000
1 X-CW Ceiling Wire Assemblies can be assembled with pre-tied wire lengths of 4', 6', 8', 10', and 12'.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 77
Product Description
3.3.3.2
Material Specifications
3.3.3.3
Technical Data
3.3.3.4
Ordering Information
Listings/Approvals
ICC-ES (International Code Council)
ESR-2184
COLA (City of Los Angeles)
RR 25651
Item
Material
X-C Fastener
X-U Fastener
X-AL-H Fastener
CC27 Clip
Wire2
Carbon Steel
Carbon Steel
Carbon Steel
Carbon Steel
Carbon Steel
Steel
Diameter/Thickness
0.138"
0.157"
0.177"
13 GA
12, 9 or 8 GA
Plating
5 m Zinc1
5 m Zinc1
5 m Zinc1
5 m Zinc1
5 m Zinc1
1 ASTM B633, SC 1, Type III. Reference Section 2.3.3.1 for more information.
2 Pre-mounted ASTM A641/A641M Class 1 wires come attached with a minimum of three tight turns
in 1-1/2" length.
Tension
lb
(kN)
160
(0.71)
220
(0.98)
160
(0.71)
150
(0.67)
205
(0.91)
205
(0.91)
45 Degree
lb
(kN)
210
(0.93)
260
(1.16)
210
(0.93)
145
(0.76)
Tension
lb
(kN)
80
(0.36)
125
(0.56)
80
(0.36)
125
(0.56)
175
(0.78)
205
(0.91)
175
(0.78)
205
(0.91)
45 Degree
lb
(kN)
90
(0.40)
150
(0.67)
70
(0.31)
130
(0.62)
1 The tabulated allowable load values apply to the powder-actuated ceiling clip assemblies only, using a safety factor that is greater than or equal to 5.0, calculated in accordance with ICC-ES AC70. Connected components, including wires*, must be investigated separately.
2 Allowable values are for fasteners installed in concrete having the designated compressive strength at the time of installation.
3 Concrete thickness at the point of penetration must be a minimum of the fastener embedment depth plus 1-1/2.
4 Multiple fasteners are recommended for any attachment.
* Note: For Hilti supplied wire, the recommended allowable load capacities of 12, 9 and 8 gauge wire are 210, 400 and 500 lb, respectively.
78 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Lower Flute
Shear
lb
(kN)
275
(1.22)
325
(1.45)
275
(1.22)
240
(1.07)
Tension
lb
(kN)
50
(0.22)
65
(0.29)
150
(0.69)
70
(0.31)
45 Degree
lb
(kN)
120
(0.53)
130
(0.58)
160
(0.71)
145
(0.65)
Upper Flute
Shear
lb
(kN)
285
(1.27)
325
(1.45)
285
(1.27)
240
(1.07)
Tension
lb
(kN)
105
(0.47)
130
(0.58)
170
(0.76)
160
(0.71)
45 Degree
lb
(kN)
240
(1.07)
265
(1.18)
240
(1.07)
240
(1.07)
1 The tabulated allowable load values apply to the powder-actuated ceiling clip assemblies only, using a safety factor that is greater than or equal to 5.0, calculated in accordance with ICC-ES AC70. Connected components, including wires*, must be investigated separately.
2 Allowable values are for fasteners installed in concrete having the designated compressive strength at the time of installation.
3 Testing completed in 3" deep composite floor deck having a minimum steel deck thickness of 20 gauge (0.0358") and a minimum yield strength (Fy) of 38 ksi.
Lower and upper flute width must be a minimum of 4-1/2". Figure 3 in Section 3.3.1.3 shows nominal flute dimensions, fastener locations and load orientations
for the steel deck profile. Concrete thickness at the point of penetration must be a minimum of the fastener embedment plus 1-1/2".
4 Multiple fasteners are recommended for any attachment.
* Note: For Hilti supplied wire, the recommended allowable load capacities of 12, 9 and 8 gauge wire are 210, 400 and 500 lb, respectively.
Allowable Loads for Hilti Ceiling Clip Assemblies in Minimum ASTM A36 (Fy 36 ksi, Fu 58 ksi)1,2
Steel Thickness (in.)
Ceiling Clip Assembly
X-CC27 U19
X-CC27 U22
Tension
lb
(kN)
375
1/4
(1.62)
Shear
lb
(kN)
410
(1.82)
Tension
lb
(kN)
375
3/8
(1.62)
Shear
lb
(kN)
410
(1.82)
Tension
lb
(kN)
375
1/2
(1.62)
Shear
lb
(kN)
410
(1.82)
1 The tabulated allowable load values apply to the powder-actuated ceiling clip assemblies only, using a safety factor that is greater than or
equal to 5.0, calculated in accordance with ICC-ES AC70. Connected components, including wires*, must be investigated separately.
2 Multiple fasteners are recommended for any attachment.
* Note: For Hilti supplied wire, the recommended allowable load capacities of 12, 9 and 8 gauge wire are 210, 400 and 500 lb, respectively.
Fastener Length
in. (mm)
Shank
in. (mm)
Washer
Packaging Qty1
X-CC27 C27P8T
X-CC27 C32P8T
X-CC27 U22P8T
X-CC27 U27P8T
X-CC27 ALH22P8T
X-CC27 ALH27P8T
1 (27)
1-1/4 (32)
7/8 (22)
1 (27)
7/8 (22)
1 (27)
0.138 (3.5)
0.138 (3.5)
0.157 (4.0)
0.157 (4.0)
0.157 (4.0)
0.177 (4.5)
8 mm metal tophat
8 mm metal tophat
8 mm metal tophat
8 mm metal tophat
8 mm metal tophat
8 mm metal tophat
1 Ceiling clip and fastener combinations can be assembled with pre-tied wire lengths of 4', 6', 8', 10' and 12'.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 79
Product Description
3.3.4.2
Material Specifications
3.3.4.3
Technical Data
3.3.4.4
Installation Instructions
3.3.4.5
Ordering Information
Fastener
Material
Base
Material
Fastener Plating1
1/4" EL WS
Carbon Steel
Wood
8 m Zinc
1/4" EL S
Carbon Steel
Steel Deck 20 - 25
gauge and Wood
8 m Zinc
1/4" EL SD
Carbon Steel
Steel Deck
16 - 22 gauge
8 m Zinc
1 Zinc plated per EN/ISO 4042 A3F. Reference Section 2.3.3.1 for more information.
1/4" EL WS
1/4" EL S
Allowable Loads for Hilti Eye Lag Ceiling Fastening Hanger Installed in Wood1,3,4,5
Wood4
Fastener
Description
Tension
lb (kN)
1/4" x 3" EL WS
1/4" x 2-3/4" EL S
45-Degree2
lb (kN)
185 (0.82)
135 (0.60)
260 (1.15)
1 The tabulated allowable load values are for the Eye Lag screws only, using a safety factor of 3.0 per
ICC-ES AC233 and AC118. Ceiling wires or other attachments must be investigated in accordance
with accepted design criteria.
2 Oblique load applied 45-Degrees from the longitudinal axis of the fastener.
3 Based on minimum 1-1/2" Eye Lag screw penetration into the wood member
4 Based on testing in wood with minimum specific gravity of 0.50. For wood members with different
specific gravity measurements, refer to Section 11 of the National Design Specification for Wood
Construction.
1/4" EL SD
5 For edge, end distance and spacing requirements, refer to Table 11.5.1E of the National Design
Specification for Wood Construction.
Allowable Loads for Hilti Eye Lag Ceiling Fastening Hanger Installed in Sheet Steel1,2,3
Steel Thickness, ga. (in.)
25
(0.021)
Fastener
Description
22
(0.030)
20
(0.036)
18
(0.048)
16
(0.060)
Tension
(lb) (kN)
45Degree4
(lb) (kN)
Tension
(lb) (kN)
45Degree4
(lb) (kN)
Tension
(lb) (kN)
45Degree4
(lb) (kN)
Tension
(lb) (kN)
45Degree4
(lb) (kN)
Tension
(lb) (kN)
45Degree4
(lb) (kN)
1/4" x 2-3/4" EL S
60 (0.26)
70 (0.31)
110 (0.49)
150 (0.67)
150 (0.67)
230 (1.02)
1/4" x 2" EL SD
1/4" x 3" EL SD
75 (0.33)
100 (0.44)
115 (0.51)
140 (0.62)
165 (0.73)
225 (1.00)
215 (0.96)
235 (1.04)
1 The tabulated allowable load values are for the Eye Lag screws only, using a safety factor of 3.0 per ICC-ES AC233 and AC118. Ceiling wires or other
attachments must be investigated in accordance with accepted design criteria.
2 Values are based on ASTM A653 grade steel having a minimum yield strength of 33,000 psi.
3 Based on minimum three full threads penetration through the sheet steel member.
4 Oblique angle load applied 45-Degrees from the longitudinal axis of the fastener.
Warning: Because of the potential for delayed hydrogen assisted stress corrosion cracking, many hardened steel
fasteners are not recommended for use with dissimilar metals or chemically treated wood when moisture may be
present or in corrosive environments. For further information, contact Hilti Technical Support at 1-877-749-6337.
80 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
End Connections
Side Connections
Face Connections
Shank
in. (mm)
Fastener Length
in. (mm)
Base
Material
Eye Lag screw - 1/4 x 3" wood screw zinc (EL WS)
Eye Lag Screw - 1/4" x 4" wood screw zinc (EL WS)
Eye Lag Screw - 1/4" x 5" wood screw zinc (EL WS)
Eye Lag screw - 1/4 x 2-3/4" sharp zinc (EL S)
Eye Lag screw - 1/4 x 2" self drilling zinc (EL SD)
Eye Lag screw - 1/4 x 3" self drilling zinc (EL SD)
1/4 (6.3)
1/4 (6.3)
1/4 (6.3)
1/4 (6.3)
1/4 (6.3)
1/4 (6.3)
3 (76)
4 (102)
5 (127)
2-3/4 (70)
2 (51)
3 (76)
Wood
Wood
Wood
Sheet Steel 20-25 ga. and Wood
Sheet Steel 16-22 ga.
Sheet Steel 16-22 ga.
Pole Tool
Description
Notes
Quantity
The pole tool can be used either by hand or with a 1/2" variable speed drill.
The pole tool can be used either by hand or with a 1/2" variable speed drill.
1 pcs
1 pcs
Telescopic Screw
Ceiling Tool
1/4" EL WS
1/4" EL S
Quantity
100 pcs
100 pcs
100 pcs
100 pcs
1/4" EL SD
Warning: Because of the potential for delayed hydrogen assisted stress corrosion cracking, many hardened steel
fasteners are not recommended for use with dissimilar metals or chemically treated wood when moisture may be
present or in corrosive environments. For further information, contact Hilti Technical Support at 1-877-749-6337.
82 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Corrosion Resistance2
Grating/
Checkerplate Height
in. (mm)
Base Steel
Thickness
in. (mm)
Connection
Type
Hot-Dipped
Galvanized
Stainless
Steel
X-FCM Grating
Disk System
X-FCM-M
Duplex Coated2
X-FCM-R
X-FCP Checkerplate
Disk System
X-FCP-F
Duplex Coated2
X-FCP-R
Checkerplate
1/4 to 1/2 (6 to 12)
X-GR RU Grating
Fastening System
Duplex Coated2
Steel Grating
1 to 1-1/2 (25 to 38)
1/4 to 1/24
(6 to 12)
Powder-Actuated
X-MGR Grating
Fastening System
Minimum 45 m
Steel Grating
1 to 1-1/2 (25 to 38)
1/8 to 1
(3 to 25)
Mechanical
1/43
( 6)
Powder-Actuated
Powder-Actuated
1. Reference entire section for specific details on allowable load values, selection and installation. More information on X-FCM Grating and X-FCP Checkerplate
Disk Systems can be found in Section 3.4.2. More information on X-GR RU and X-MGR Grating Systems can be found in Section 3.4.3.
2. Reference Section 2.3.3.1 for more information on coatings and corrosion resistance.
3. X-BT M8 threaded studs require a minimum steel thickness of 5/16" (8 mm) to ensure no through point penetration. X-CRM8 threaded studs have a maximum
application limit of 1/2" (12 mm).
4. Fastening X-GR RU fasteners into base material thicknesses greater than 1/2" (12 mm) is possible when pre-drilling is used. Reference X-GR RU section for
more information.
5. Disk or saddle may be removed easily. Threaded stud or base will remain in base steel unless removed by overloading fastener.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 83
Product Description
Technical Data
3.4.2.4
Installation Instructions
3.4.2.5
Ordering Information
X-FCM
X-FCP
HILTI
HILTI
HILTI
Guide Specification
05500 Metal Fabrications
05530 Grating
Disk: X-FCM disk shall be duplex
coated carbon steel or stainless steel,
which consists of an assembly of a disk
and an 8 mm internally threaded screw
manufactured by Hilti.
Stud: Powder-actuated threaded stud
for attaching the X-FCM disk shall be
X-CRM8-15-12, X-BT M8-15-6 SN12-R
stainless steel studs manufactured
by Hilti.
Installation: Contact a manufacturers
representative from Hilti to provide
training to the operators at the
project site.
05540 Floor Plates
Disk: X-FCP disk shall be duplex coated
carbon steel or stainless steel, which
consists of an assembly of a disk and
an 8 mm internally threaded screw
manufactured by Hilti.
Stud: Powder-actuated threaded stud
for attaching the X-FCP disk shall be
X-CRM8-9-12 or X-CRM8-15-12
stainless steel studs manufactured
by Hilti.
Installation: Contact a manufacturers
representative from Hilti to provide
training to the operators at the
project site.
Listings/Approvals
ABS (American Bureau of Shipping)
for X-FCM-R and X-FCP-R
Lloyds Register
for all X-FCM types and X-FCP-R
DNV Certification
for X-FCM-M and X-FCM-R
GL (Germanischer Lloyd)
for X-FCM-M and X-FCM-R
84 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Component
Disk
Threaded Extension
Threaded Stud
1 Duplex coating is comparable to 45 m HDG coating. Reference Section 2.3.3.1 for more information.
Allowable Static Tension Loads for X-FCM-M or X-FCM-R with Grating, lb (kN)1,2,4
Rectangular Grid Barspacing in. (mm)
(19)
(30)
3/4
1-3/16
180
(0.8)
180
(0.8)
315
(1.4)
225
(1.0)
Fastener
Description
X-FCM-M
X-FCM-R
3/4
405
405
1 Allowable loads represent the capacity of the Hilti Grating System only. The capacity of the grating must be investigated in accordance with accepted
design criteria.
2 Unless otherwise noted, load values are limited by plastic deformation of the X-FCM disk.
3 Allowable load value is limited by recommended load for threaded stud. Reference Section 3.2.9.
4 X-FCM-M and X-FCM-R Fastening Systems resist shear by friction and are not suitable for explicit shear load designs (e.g. diaphragms). Depending on
surface characteristics, shear loads of up to 65 lb (0.3 kN) will not result in permanent deformation. Therefore, small unexpected shear loads can generally be
accommodated without damage.
Fastener
Description
X-FCP-F
X-FCP-R
405
(1.8)
L
19.6
[0.768"]
16
[0.630"]
10.3
L+4[0.157"]
8.6[0.339"]
50[1.969"]
Duplex Coated
X-FCM-M 25/30
Grating
Disk
[0.406"]
5[0.197"]
Threaded
Stud
Stainless Steel
X-FCM-R 25/30
Grating Height
in.
(mm)
in.
(mm)
0.906
(23)
1 to 1-3/16
(25-30)
X-FCM-M 1 -1/4
X-FCM-R 1-1/4
1.063
(27)
1-1/4
(32)
X-FCM-M 35/40
X-FCM-R 35/40
1.299
(33)
1-3/8 to 1-9/16
(35-40)
X-FCM-M 45/50
X-FCM-R 45/50
1.693
(43)
1-3/4 to 2
(45-50)
X-CRM8-15-12 FP10
X-BT M8-15-6 SN12-R
1 480 hour salt spray test per DIN 50021 and 10 cycles Kesternich test per DIN 50018/2.0 (Comparable to 45 microns
HDG coating).
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 85
t II
hNVS
TMAX
L
7
16
26.5
23
L
20
2
Tightening tool:
Hilti screwdriver SF 18-A, SFH
18-A, SF 144-A or SFH 144
with 5 mm Torx Bit
Set clutch to appropriate
setting to obtain desired
torque.
thII
NVS
hhNVS
X-CRM8-15-12
hNVS = 5/8" to 25/32"
(16.0 to 20.0 mm)
t II = 1/4" to 1/2"
(6 to 12 mm)
Tightening torque
21.5
Governing requirement:
Governing requirement:
Minimum 2 mm clearance
between X-FCM and sur- Minimum 5 mm thread
engagement at the
face of base steel to allow
minimum allowable
for deflections
stand-off, hNVS.
Example:
Note:
X-FCM 25/30
Min. grating ht. = 23 + 2 = 25 mm
The maximum grating
Max. grating ht. = 23 + 7 = 30 mm
height for an X-FCM
type can be extended if
Grating height of 32 can be
hNVS is tightly controlled
accommodated if
(e.g. at 18 mm instead of
hNVS 18 mm
16 mm).2
1 Reference Section 3.2.10 for more details on proper installaton of X-BT fasteners.
2 Maximum grating height can be extended with the use of the X-SEA-R30 M8. Reference Section 3.4.2.5 for photo.
DX 750
1 2 3 4
R
30
11/16"
hNVS
NVS
11/16"
* These are abbreviated instructions which may vary by application. ALWAYS review/follow the instructions accompanying the product.
86 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
X-FCP Disk1
DX 460-GR Stud
1/4 to 21/64
(6.4 to 8.3)
11/32 to 1/2
(8.7 to 12.7)
1/4 to 1/2
(6.4 to 12.7)
X-FCP-F5/10
X-FCP-R5/10
X-FCP-F5/10
X-FCP-R5/10
X-CRM8-9-12P10
Stud Stand-off 31/64" 37/64"
X-CRM8-15-12P10
Stud Stand-off 41/64" 25/32"
X-CRM8-9-12P8
Stud Stand-off 31/64" 37/64"
X-CRM8-15-12P8
Stud Stand-off 41/64" 25/32"
Optional
Optional
Trec
3.7 6 ft-lb
(5-8 Nm)
* These are abbreviated instructions which may vary by application. ALWAYS review/follow the instructions accompanying the product.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 87
Coating/Material
Box Qty
X-FCM-M 25/30
X-FCM-M 35/40
X-FCM-M 1-1/4
X-FCM-M 45/50
X-FCM-R 25/30
X-FCM-R 35/40
X-FCM-R 1-1/4
X-FCM-R 45/50
Duplex Coated
Duplex Coated
Duplex Coated
Duplex Coated
Stainless Steel
Stainless Steel
Stainless Steel
Stainless Steel
100
100
100
100
100
100
100
100
Description
Coating/Material
Box Qty
X-CRM8-15-12 FP10
X-CRM8-15-12 P8
X-CRM8-9-12 FP10
X-CRM8-9-12 P8
X-BT M8-15-6 SN12-R
Stainless Steel
Stainless Steel
Stainless Steel
Stainless Steel
Stainless Steel
100
100
100
100
100
Description
Coating/Material
Box Qty
X-FCP-F5/10
X-FCP-R5/10
X-FCP Sealing Ring
Duplex Coated
Stainless Steel
Polyurethane
200
200
200
Description
Coating/Material
Box Qty
X-SEA
Stainless Steel
100
Threaded Studs
Checkerplate Disks
Grating Extensions
88 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
3.4.3.1
Product Features:
Product Description
3.4.3.3
Technical Data
3.4.3.4
Installation Instructions
3.4.3.5
Ordering Information
Nut Holder
X-MGR
Material
Coating1
Carbon Steel
65 m Zinc
Carbon Steel
60 m Zinc
Carbon Steel
45 m Zinc
Stainless Steel
Bearing Bar
Spacing4
in. (mm)
Allowable
Tension Load
lb. (kN)
X-GR RU
1 to 1-1/4
(25 to 32)
1/4 to 1/2
(6 to 12)5
180 (0.8)
X-MGR
1-3/16
( 30)
1/8 to 1
(3 to 25)
135 (0.6)
1 Allowable loads represent the static capacity of the Hilti Grating System only. The capacity of the grating
must be investigated in accordance with accepted design criteria.
2 Allowable load values are limited by plastic deformation of the X-GR RU or X-MGR saddle clip.
3 X-GR RU and X-MGR Grating Fastening Systems resist shear by friction and are not suitable for explicit
shear load designs, (e.g. diaphragms). Depending on surface characteristics, shear loads of up to 65 lb
(0.3 kN) will not result in permanent deformation. Therefore, small unexpected shear loads can generally
be accommodated without damage.
4 Reference installation instructions for more details regarding bearing and cross bar dimensions.
5 Fastening X-GR RU fasteners into base material thicknesses greater than 1/2" (12 mm) is possible when
pre-drilling is used. Reference X-GR RU installation instructions for more information.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 89
X-GR RU
X-MGR
Bearing Bar
Spacing2
in. (mm)
Base Steel
Thickness3
in. (mm)
DX Tool
1 to 1-1/4
(25 to 32)
1/4 to 1/2
(6 to 12)
DX 460-GR
with 6.8/11M
black cartridges
Torque Setting2
3-5
3-5
3-5
3-5
NVS
NVS
1 These are abbreviated instructions which may vary by application. ALWAYS review/follow the instructions accompanying the product.
2 Tool torque settings are for guideline purposes. Tool wear and temperature as well as battery charge will influence torque characteristics.
90 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Powder-Actuated
Fastener
Grating Height
in. (mm)
X-MGR-W60
None
1 to 1-1/2
(25 to 38)
Minimum
Cross Bar Spacing1
in. (mm)
1-3/16
(30)
Bearing Bar
Spacing1
in. (mm)
1
(25)
Maximum Bearing
Bar Thickness1
in. (mm)
3/16
(4.8)
Base Steel
Thickness
in. (mm)
1/8 to 1
(3 to 25)
1 Reference step 2 of the X-MGR Installation Procedures below for more details on bar spacing and thickness requirements.
4. Check
4a. Check that the indentation line on
the clip is positioned under the steel
flange as shown below.
indentation line
X-MGR
W60
1"
1-3/16" 3/16"
(25 mm) (30 mm) (4.8 mm)
Torque Setting2
5-9
5-9
5-9
5-9
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 91
Guide Sleeve
Replacement Parts
Description
X-GR RU Fastener
Fastener Only Packs
Non-Combo Description
X-GR RU 1" 25/30 CR 20 P8
X-GR RU 1-1/4" CR 20 P8
X-GR RU 1-1/2" CR 20 P8
Qty
100 pcs
100 pcs
100 pcs
X-MGR Fastener
Fastener Only Packs
Description
X-MGR W 60
Qty
20 pcs
Qty
100 pcs
Qty
1 pcs
1 pcs
10 pcs
1 pcs
92 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
X-EDN19/X-EDNK22 Frame
Fasteners for Bar Joist
Please see the sections 3.5.2, 3.5.3 and 3.5.4 for more
information on specific product approvals, evaluations and
application limits.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 93
DX
ENP
G'
HSN
Qf
Qs
Sf
Ss
t f ( t || )
Hs
Nr
Qn
Rg
wr
Ycon
94 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 95
AISI S905 Test Methods for Mechanically Fastened ColdFormed Steel Connections
ASTM E1190 Standard Test Methods for Strength of
Power-Actuated Fasteners Installed In Structural Members
ICC-ES AC70 Acceptance Criteria for Fasteners Power
Driven Into Concrete, Steel and Masonry Elements
ICC-ES AC118 Acceptance Criteria for Tapping Screw
Fasteners
96 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
30
'-0
"
"
24'-0
Load (kips)
Displacement [inch]
3/8"
t ||
3/8"
bx 8 t ||
Figure 7: Edge Distance Recommendations
Extra care must be taken at the endlap and corner lap
conditions where multiple layers of steel deck nest or interlock
on adjacent panels. It is particularly important that endlap
and corner lap conditions of two and four deck layers must
be snug and tight against one another and the supporting
steel frame in order for the fastening to be made as shown
in Figure 8. Tight endlap and corner lap requirements are
independent of the fastening type and contribute directly to
the performance of arc spot welds, screws, powder-actuated
fasteners, punches and crimps/clinches. If the steel deck
endlaps and corner laps are not tight, a proper fastening
cannot be made.
98 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Piston Mark
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 99
hNVS within
optimal range*
hNVS within
optimal range*
DX 460-SM
DX 860-HSN
SDT 30
DX 76
X-ENP-19 L15
DX 860-ENP-L
SDT 30
102 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Fastener
Type2
Recommended
Installation Tool
X-EDN19 THQ123
Bar Joist and Structural Steel
3/16" (5 mm) tf 3/8" (10 mm)
DX 860-HSN
X-EDNK22 THQ12
Bar Joist
1/8" (3 mm) tf 1/4" (6 mm)
DX 860-HSN
1 Steel base material tensile strength (fu) shall be in a range of 58 to 91 ksi for base steel thicknesses (tf) less than or equal to 5/16".
For the X-EDN19 THQ12 fastener in base steel thicknesses (tf) greater than 5/16", the tensile strength shall be in a range of 58 to 68 ksi.
2 X-EDN19 and X-EDNK22 fit in all deck types except A-deck.
3 This fastener can be used with structural steel within the thickness ranges shown.
Fastener
Type2
Recommended
Installation Tool
X-ENP-19 L15
DX 860-ENP-L
1 Steel base material tensile strength (fu) shall be in a range of 58 to 91 ksi for all base steel thicknesses (tf) greater than or equal to 1/4".
2 X-ENP-19 L15 fasteners fit in all types of deck except A and F.
Fastener
Type1
Recommended
Installation Tool
S-SLC 01 M HWH
18 to 26
SDT 30
S-SLC O2 MHWH
16 to 22
SDT 30
Hilti #10 HWH Screw
16 to 26
SDT 30
1 For use with all types of nestable deck or screwable interlocking deck.
2 Other sidelap connector types are possible with Hiltis powder actuated frame fasteners. Please reference the Steel Deck Institute (SDI)
Diaphragm Design manual 3rd Edition (DDM03).
3 Use of S-SLC 01 M HWH with 18 gauge steel deck is recommended only for standard tensile strength (45 fu 65 ksi) steel deck.
For high tensile strength (fu > 65 ksi) 18 gauge steel deck, use S-SLC 02 M HWH.
Sealing Caps
The SDK2 is an SAE 316 stainless steel sealing cap with a
neoprene seal. This is installed over the head of the X-ENP-19
fastener using the SDK2 hand setting
tool. The SDK2 sealing cap provides
added corrosion protection for exposed
exterior steel deck applications in
SDK2 Setting Tool
accordance with IBC requirements.
X-ENP-19 L15
hnvs = 8.2 mm- 9.8 mm
Note: The sealing cap and fastener must be installed correctly to achieve a water-resistant seal. Contact Hilti for details.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 103
The DX 860-HSN stand up decking tool is a fully automatic powderactuated tool designed for attaching steel deck to steel base materials.
With a high fastening rate and 40-fastener magazine, the DX 860HSN can significantly help reduce the time it takes to attach deck.
Fastenings can be made on very thin support structures without the
need for weld washers. Suitable for base steels with a thickness of
1/8" to 3/8". Fastens X-EDN19 THQ12M and X-EDNK22 THQ12M
collated fasteners.
DX 460-SM
DX 76
The SDT 30 stand up decking tool is a steel deck sidelap and frame
fastening tool. Combined with the DX 860-HSN or DX 860-ENPL, these tools deliver a high speed, high productivity system for
mechanical attachment of steel deck. The SDT 30 can consistently
drive up to 50 Hilti sidelap connectors (SLC) in the sidelaps of 16
to 26 gauge nestable decks before reloading. Its comfortable,
durable design features an 18 position torque clutch to provide
consistent fastening quality. In a competitive market, the SDT 30
represents a major gain in productivity essential to staying on time
and on budget.
104 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Figure 13:
Hilti Power
Adjustment Guide
> 3/4"
Black
3
Black
2
5/16"
1/4"
Yellow
4
Red 4
or
Black 1
3/16"
3/8"
5/8"
Black
2
3/8"
Red
3
3/16"
5/16"
Yellow
4
1/8"
X-EDN19
X-EDNK22
1/4"
Blue 3
or
Red 1
X-ENP-19
1 Cartridge recommendations for the X-ENP-19 fastener are acceptable for all current Hilti Decking Tools for attachment to structural steel.
Cartridge recommendations for the X-EDN19 and X-EDNK22 fasteners are for the DX 860-HSN. Cartridge recommendations for the
DX 460-SM can be found in the tool operator manual. Recommendations are guidelines only and require verification on each site.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 105
Date:
Phone:
DDAATT:
Decking Installer:
Phone:
Fax/e-mail:
Engineer of Record:
Phone:
Fax/e-mail:
Project Name:
Total Area:
Deck Manufacturer:
Submittal Recipient:
Account Manager
Zone _______
Decking Installer
Support Steel
Bar
Str.
Joist Steel
Other:
Design Diaphragm Shear
Capacity (plf) ________
Zone _______
Frame Type
Frame Pattern
1/2" PW
36 / 9
5/8" PW
30 / 7
3/4" PW
24 / 5
#12 or #14 Screw __ / 4
Other
3
__
Support Steel
Sidelap Type
Sidelap Pattern
Base Thickness
#10 Screw
_____# Per Span
< 3/16"
#12 Screw
_____(in.) On Center 3/16"
Button Punch
1/4"
_______(in.) Top Seam Weld Length
5/16"
Proprietary Punch System
3/8"
Other
> 3/8"
Bar
Str.
Joist Steel
Zone _______
Frame Type
Frame Pattern
1/2" PW
36 / 9
5/8" PW
30 / 7
3/4" PW
24 / 5
#12 or #14 Screw __ / 4
Other
3
__
Support Steel
Frame Type
Frame Pattern
1/2" PW
36 / 9
5/8" PW
30 / 7
3/4" PW
24 / 5
#12 or #14 Screw __ / 4
Other
3
__
Exposed to Weather
Sidelap Type
Sidelap Pattern
Base Thickness
#10 Screw
_____# Per Span
< 3/16"
#12 Screw
_____(in.) On Center 3/16"
Button Punch
1/4"
_______(in.) Top Seam Weld Length
5/16"
Proprietary Punch System
3/8"
Other
> 3/8"
Bar
Str.
Joist Steel
Exposed to Weather
Exposed to Weather
Sidelap Type
Sidelap Pattern
Base Thickness
#10 Screw
_____# Per Span
< 3/16"
#12 Screw
_____(in.) On Center 3/16"
Button Punch
1/4"
_______(in.) Top Seam Weld Length
5/16"
Proprietary Punch System
3/8"
Other
> 3/8"
Notes
Fax or email completed forms to Hilti Technical Support at (918) 459-3004 or deck@hilti.com.
106 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Date:
Phone:
DDAATT:
Decking Installer:
Phone:
Fax/e-mail:
Engineer of Record:
Phone:
Fax/e-mail:
Project Name:
Total Area:
Deck Manufacturer:
Submittal Recipient:
Account Manager
Decking Installer
Bar
Str.
Joist Steel
Zone _______
Support Steel
Other:
Design Diaphragm Shear
Capacity (plf) ________
Deck Gauge
28
26
24
22
20
18
16
Frame Type
Frame Pattern
1/2" PW
36 / 9
5/8" PW
30 / 7
3/4" PW
24 / 5
#12 or #14 Screw __ / 4
Other
3
__
Sidelap Type
Sidelap Pattern
#10 Screw
_____ # Per Span
#12 Screw
_____ (in.) on Center
Button Punch
____ (in.) Top Seam Weld Length
Other
Base Thickness
< 3/16"
3/16"
1/4"
5/16"
3/8"
> 3/8"
.00075 bw s2
12"
6 x 6 W 1.4 x W 1.4
6 x 6 W 2.0 x W 2.0
6 x 6 W 2.9 x W 2.9
6 x 6 W 4.0 x W 4.0
4 x 4 W 4.0 x W 4.0
6 x 6 W 7.5 x W 7.5
6 x 6 W 8.3 x W 8.3
18"
.00025 bw s2
24"
30"
36"
Notes
Fax or email completed forms to Hilti Technical Support at (918) 459-3004 or deck@hilti.com.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 107
Fastener
spacing
6"
6"
6"
6-12-12-6
12"
18"
6"
6-18-6
12-18
6"
6"
8"
4.0
78
61
53
37
29
21
53
34
24
53
29
41
4.5
69
56
48
33
26
19
48
30
22
48
26
37
5.0
63
50
43
30
22
17
43
28
20
43
22
34
Support Spacing, ft
5.5
6.0
59
53
45
43
39
37
28
26
22
21
16
15
39
37
26
24
19
17
39
37
22
21
31
29
6.5
50
39
34
24
19
14
34
22
16
34
19
27
7.0
46
36
32
23
18
13
32
21
15
32
18
25
8.0
40
33
28
20
16
12
28
19
14
28
16
22
Common
Thickness
Standard
Dimensions
1.5"
6"
2.5"
16-24 GA
1.75"
36"
6"
1.75"
16-24 GA
1.5"
BI
2.5" 3.5"
36"
8"
16-22 GA
1.75"
24"
0.75"
3"
2.75"
1.5"
6"
1.75"
18-22 GA
0.5"
36"
12"
1"
Composite
Deck
3"
7.25"
Nominal Sheet
Steel Thickness, t
in. (mm)
16
0.0598 (1.52)
18
0.0474 (1.21)
20
0.0358 (0.91)
22
0.0295 (0.76)
24
0.0239 (0.61)
26
0.0179 (0.45)
28
0.0149 (0.38)
0.75"
Gauge
(GA)
16-22 GA
36"
9/16"
4.75"
Form Deck
24-28 GA
1.5"
1"
2.5"
30"
108 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Pn
Qf
, plf
= (2 x 1 + 2 x 2 + n e ) x
S ni = {2 x A x ( - 1) + B} x
S nc = Q f x
Qf
, plf
N 2 x B2
, plf
x N2 + B2
(Eq. 2.2-2)
(Eq. 2.2-4)
(Eq. 2.2-5)
1
x [ 2 x 2 x ( xp2 ) + 4 ( xe2 ) ]
w2
1.5 x v
0.7
240 x t
s =
Qs
Qf
where:
t = nominal steel deck thickness, in. (Reference Table 6)
w = deck width
N = number of fasteners per unit length across the width, ft -1
xe = xp = distance from panel centerline to any fastener in a
panel at the end (xe) or purlin (xp) supports
S = nominal diaphragm shear strength, plf
v = span, ft
= panel length = 3 x v, ft
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 109
With:
C = 29,500 x
(Eq. 3.3-3)
Dn =
1000
, micro-inches/lb
G'
1
t
x Sf x
S
1 + 2 + ns x f
w
Ss
x x 12 (Eq. 3.3-1)
(Eq. 3.3-2)
x 12
Table 7 Diaphragm Strength (S) and Stiffness Factor (G') Equation Variable Values
Deck
Type
1-1/2"
Wide
RibBDeck or
BIDeck
1 end
Fastener
destribution
Pattern
Factor
36/11
36/9
36/7
36/5
36/4
36/3
2 purlin
destribution
Factor
xe2,
in.2
xp2,
in.2
N,
ft-1
22 GA
20 GA
18 GA
16 GA
3.667
3.000
2.000
1.667
1.333
1.000
1944
1656
1008
936
720
648
1944
1656
1008
936
720
648
2
2
1
1
1
1
3.000
2.333
2.000
1.333
1.000
0.667
1548
1548
1548
9096
12864
26508
1164
1164
1164
6804
9624
19824
756
756
756
4464
6312
13008
540
540
540
3144
4452
9180
3.667
3.000
2.000
1.667
1.333
1.000
Configuration
22
(0.0295)
Min. Deck
Frame Fastener
Deck
Sidelap
Tensile (Yield) Base Material
Type
Connector1,2
Strength, ksi
Thickness, in.
45 (33)
92 (80)
BI
B
or
BI
45 (33)
45 to 92
(33 to 80)
X-EDNK22
1/8 tf < 3/16
Hilti
SLC
X-EDNK22
3/16 tf 1/4
Hilti
SLC
X-EDN19
3/16 tf 3/8
Hilti
SLC
X-ENP-19
tf 1/4
Hilti
SLC
X-EDNK22
1/8 tf < 3/16
Hilti
SLC
X-EDNK22
3/16 tf 1/4
Hilti
SLC
X-EDN19
3/16 tf 3/8
Hilti
SLC
X-ENP-19
tf 1/4
Hilti
SLC
X-EDNK22
1/8 tf < 3/16
Hilti
SLC
X-EDNK22
3/16 tf 1/4
Hilti
SLC
X-EDN19
3/16 tf 3/8
Hilti
SLC
X-EDNK22
or X-EDN19
1/8 tf 3/8
X-ENP-19
tf 1/4
Hilti #10
HWH Screw
Hilti #10
HWH Screw
Qf, lb
Qs, lb
Correlation
Factor, c
1357
844
1.155
1590
844
1.121
1590
844
1.121
1597
844
1.257
1357
844
1.155
1941
954
1.052
1941
954
1.052
1964
954
1.197
1357
844
1.155
1516
882
1.284
1516
882
1.284
1489
633
20
(0.0358)
Qf, lb
1.000
1603
Qf, lb
1933
Qs, lb
Correlation
Factor, c
1865
1701
1.203
2663
1701
1.066
2663
1701
1.066
2764
1701
1.106
1865
1701
1.203
2698
1859
1.058
2698
1859
1.058
3022
1859
1.108
1865
1591
1.203
2450
1591
1.140
2450
1591
1.140
2348
1018
1.000
633
1.000
Qs, lb
Correlation
Factor, c
1824
1260
1.172
2107
1260
1.102
2107
1260
1.102
2112
1260
1.204
1824
1260
1.172
2208
1341
1.054
2208
1341
1.054
2165
1341
1.166
1712
1111
1.172
1712
1111
1.233
1712
1111
1.233
1795
769
18
(0.0474)
16
(0.0598)3
Qf, lb
1.000
769
1.000
2529
1.000
1018
1.000
Qs, lb
Correlation
Factor, c
3035
2024
1.028
3035
2024
1.028
3079
2024
1.000
3095
2343
1.062
3095
2343
1.062
3577
2343
1.046
2553
2051
1.040
2553
2051
1.040
2924
1284
3149
1284
1.000
Min. Deck
Tensile (Yield)
Strength, ksi
45 to 92
(33 to 80)
22
(0.0295)
Frame
Fastener
Sidelap
Connector1
X-EDNK22
or X-EDN19
Hilti SLC or
Hilti #10 HWH Screw
X-ENP-19
Hilti SLC or
Hilti #10 HWH Screw
16
(0.0598)3
Sf, in./kip
Sf, in./kip
Sf, in./kip
Sf, in./kip
Ss, in./kip
Ss, in./kip
Ss, in./kip
Ss, in./kip
0.0073
0.0175
0.0044
0.0175
0.0066
0.0159
0.0040
0.0159
0.0057
0.0138
0.0034
0.0138
0.0051
0.0123
0.0030
0.0123
1 Reference Table 3 and Section 3.5.4 for more information on the proper selection of Hilti Sidelap Connectors (SLC).
Table 10 Minimum Recommended Sidelap Connector Spacing (Inches Center-to-Center) for B-Deck or BI-Deck Type
with Tensile Strength (fu) Ranging from 45 to 92 ksi
Frame Fastener
Deck
Base Material
Gauge
Thickness, in.
X-EDNK22
1/8 tf < 3/16
X-EDNK22
3/16 tf 1/4
X-EDN19
3/16 tf 3/8
X-ENP-19
tf 1/4
22
20
18
16
22
20
18
16
22
20
18
16
22
20
18
16
SLC1
#10
12
12
36/4
SLC1
#10
36/5
SLC1
#10
36/7
SLC1
#10
36/9
SLC1
#10
36/11
SLC1
#10
12
12
6
12
18
6
12
18
3
3
6
3
3
6
6
12
18
6
12
18
3
3
6
3
3
6
3
6
12
18
3
6
12
18
3
3
6
12
3
3
6
12
3
6
12
18
3
6
12
18
3
3
6
12
3
3
6
12
3
6
12
12
3
6
12
12
3
3
6
12
3
3
6
12
1 Hilti SLC spacings less than those tabulated may be used. The tabulated spacing should be used in the calculation of diaphragm shear strength when using
the Qf, Qs and c values from Table 8. Alternatively, only when the SLC spacings are less than those tabulated, the Qf, Qs and c values found in Table 8 can be
replaced by the following values.
X-EDNK22 THQ12 or X-EDN19 THQ12 All deck types, strengths and base steel thicknesses listed in Table 8
22 Gauge (0.0295 in.)- Qf = 1489 lb, Qs = 716 lb, c = 1.000
20 Gauge (0.0358 in.)- Qf = 1795 lb, Qs = 869 lb, c = 1.000
18 Gauge (0.0474 in.)- Qf = 2348 lb, Qs = 1151 lb, c = 1.000
16 Gauge (0.0598 in.) - Qf = 2924 lb, Qs = 1452 lb, c = 1.000
X-ENP-19 L15 All deck types, strengths and base steel thicknesses listed in Table 8
22 Gauge (0.0295 in.)- Qf = 1603 lb, Qs = 716 lb, c = 1.000
20 Gauge (0.0358 in.)- Qf = 1933 lb, Qs = 869 lb, c = 1.000
18 Gauge (0.0474 in.)- Qf = 2529 lb, Qs = 1151 lb, c = 1.000
16 Gauge (0.0598 in.) - Qf = 3149 lb, Qs = 1452 lb, c = 1.000
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 111
0.400
0.426
0.400
0.650
0.700
0.650
0.600
0.650
0.600
Design
Method
ASD
LRFD
LSD
Table 12- ASD and LRFD Diaphragm Shears (plf) and LSD Diaphragm Shears (N/mm) for Buckling, Sbuckling1,2
Steel Deck
Type
Standard 1-1/2Inch Deep Flutes,
6-Inches Centerto-Center
Standard 1-1/2Inch Deep Flutes,
6-Inches Centerto-Center
Steel Deck
Type
Standard 1-1/2Inch Deep Flutes,
6-Inches Centerto-Center
Moment of
Inertia,
mm4/mm
3'-0"
22
20
18
16
0.152
0.198
0.284
0.355
22
Deck
Gauge
Span, v (ft-in.)
4'-0"
5'-0"
6'-0"
7'-0"
8'-0"
9'-0"
10'-0"
11'-0"
12'-0"
8444
11000
15778
19720
4750
6188
8875
11094
ASD (PLF)
3040
2111
3960
2750
5680
3944
7100
4931
LRFD (PLF)
1551
2020
2898
3622
1188
1547
2219
2773
938
1222
1753
2191
760
990
1420
1775
628
818
1174
1467
528
688
986
1233
0.152
13511
7600
4864
3378
2482
1900
1501
1216
1005
844
20
0.198
17600
9900
6336
4400
3233
2475
1956
1584
1309
1100
18
0.284
25244
14200
9088
6311
4637
3550
2805
2272
1878
1578
16
0.355
31556
17750
11360
7889
5796
4438
3506
2840
2347
1972
900
1200
1500
1800
2100
2400
2700
3000
3300
3600
192.6
250.0
359.3
449.1
108.3
140.6
202.1
252.6
LSD (N/mm)
69.3
48.1
90.0
62.5
129.3
89.8
161.7
112.3
35.4
45.9
66.0
82.5
27.1
35.2
50.5
63.2
21.4
27.8
39.9
49.9
17.3
22.5
32.3
40.4
14.3
18.6
26.7
33.4
12.0
15.6
22.5
28.1
Moment of
Deck
Inertia,
Gauge
mm4/mm
22
20
18
16
208
270
388
485
Span, v (mm)
1 Load values based upon a safety factor () of 2.00 for ASD, a phi factor () of 0.80 for LRFD or a phi factor () of 0.75 for LSD.
2 Diaphragm shears in this table are for steel deck buckling failure mode only and are to be used as prescribed in Section 3.5.1.8. If design condition is not
tabulated, diaphragm shears for buckling may be calculated using the following equations:
For ASD, Sbuckling = ( x 106/( v)2) / 2.0 , plf
For LRFD, Sbuckling = ( x 106/( v)2) x 0.8 , plf
For LSD, Sbuckling = ( x 106/( v)2) x 0.75 , N/mm
112 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Pattern 36/3
Pattern 36/4
Pattern 36/5
Pattern 36/7
Pattern 36/9
Pattern 36/11
Note 1: Nestable B-Deck shown. Interlocking BI-Deck with screwable sidelap is also covered by the equations discussed in Section 3.5.1.8.
Note 2: Bar joist shown. Connection to structural steel members also covered by the equations discussed in Section 3.5.1.8.
Refer
to Note
2" min.
Hilti
Fastener
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 113
Design Problem:
6"
36"
Hilti
SLC
1-1/2"
X-EDN19 THQ12
Calculation Steps
Step 1: Calculate Nominal Diaphragm Shear Strength Limited by Edge Fasteners:
This calculation is not required when the number of edge connectors (ne) equals the number of sidelap
fasteners (ns). In these cases, Sne does not limit diaphragm shear strength.
SDI
DDM03
Ref.
HNA
Technical
Guide
Eq.
2.2-2
Sec.
3.5.1.8
Eq.
2.2.3
Sec.
3.5.1.8
and
Tables
7 and 8
Eq.
2.2-5
Sec.
3.5.1.8
and
Tables
7 and 8
Step 2: Calculate Nominal Diaphragm Shear Strength Limited by Interior Panel Fasteners:
S ni = {2 x A x (- 1) + B} x
with:
= 1-
1.5 x v
= {2 x 1 x (0.802 - 1) + 16.99} x
2107
18
= 1,942 plf
1.5 x 6
= 0.802 0.7
240 x t
240 x 0.0358
1
[2 x 2 x 1008 + 4 x 1008]
B = ns x s +
x [ 2 x 2 x ( xp2 ) + 4 ( xe2 ) ] = 18 x 0.598 +
= 16.99
w2
362
where:
3 x v x 12
3 x 6 x 12
ns = ne =
=
= 18
Sidelap Spacing
12
s =
= 1-
Qf
Qs
1260
=
= 0.598
2107
Qf
N 2 x B2
= 2107 x
2 x N 2 + B 2
2.00 2 x 16.99 2
= 1,798 plf
182 x 2.002 + 16.992
Step 4: Apply Correlation Factor, c, to determine Correlated Nominal Diaphragm Shear Strength
S = c x Sn = 1.102 x 1,798 = 1,981 plf
where:
Sn = least of Sne, Sni and Snc = Snc = 1,798 plf
Step 5: Apply Appropriate Conversion Factor to Determine Allowable Diaphragm Strength
SASD (wind) = S x Conversion Factor = 1,981 x 0.426 = 844 plf
Step 6: Check to See if Steel Deck Buckling Controls
Sbuckling (ASD) = 2,750 plf > SASD (wind) therefore, SASD (wind) = 844 plf 650 plf
Sec.
3.5.1.8
and
Table 8
Sec.
2.4
Table 11
Table 12
114 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
SDI
DDM03
Ref.
HNA
Technical
Guide
Eq.
3.3-3
Sec.
3.5.1.8
and
Tables
7 and 9
Roof
Deck
Const.
Handbook
Sec.
3.5.2.3
x 18 x 12 = 3.65
Where:
K = Number of frame fasteners per deck sheet per joist/beam = 6.00
C = Width of deck sheet = 3 feet
Tn,F = Controlling Ultimate Tension Capacity of frame fastener = 435 lb x 3.0 = 1,305 lb
Sec.
4.10
2.35 x 650
3.00 x 35
) + (
) 1.0 0.897 1.0
1981
435
Note: The Hilti Profis DF Diaphragm software provides full calculations for diaphragm shear and stiffness when desired.
36/3
6''
914/3
36''
152 mm
1-1/2''
914 mm
38 mm
EDN
36/3
914/4
Traditional Diaphragm
Shear Tables:
Sections 3.5.2 and
3.5.3 provide tables
in
a
format
similar
to
those published in
6''
152 mm
36''
1-1/2''
914 mm
38 mm
the SDI DDM03, CSSBI and most steel deck manufacturers'
catalogs.
152 mm
152 mm
152 mm
Optimized Diaphragm
Shear Tables:
36''
1-1/2''
914 mm Section 3.5.5
38 mmprovides
tables in an alternative format that helps a structural engineer
Steel Deck Fastening Systems
to quickly select a cost optimized Hilti frame fastener pattern,
Hilti
In all cases, diaphragm
shear
values determined
either
1.2 Deck
Fasteners
for using
Attachment
tosidelap
Bar connector
Joist (SLC) spacing and deck gauge
combination to satisfy the diaphragm shear load requirement
table format are consistent.
36/7
36/9
914/9
found in the left column of the table (Reference Figure 19).
These tables do not take into account other design factors,
These tables are
on diaphragm shear capacity only,
6'' based
6''
152 mm
such as gravity or wind uplift loads. These
requirements
36''
1-1/2''
36''
1-1/2''
914 mm
38 mm
diaphragm stiffness must be verified separately.
Allowable
Stress Design
(ASD)
- Allowable
Diaphragm Shears, SASD, (plf) and Stiffness Factors, G', (kips/in.) for
should be checked
separately
by the
structural
engineer.
152 mm
152 mm
Standard 1-1/2" Deep Flutes, 6" Center-to-Center Steel Deck (Fy 33 ksi; Fu 45 ksi) Installed with Hilti X-EDN19
or X-EDNK22 Fasteners with 36/9 or 36/7 End and Interior Support Fastener Patterns1,2,3,4
Gage
Sidelap
Spacing
Hilti SLC5,6
Factor
4'-0"
5'-0"
311
331
36/3 -42
36/3 -48
36/3 -48
36/3 -48
36/3 -24
36/4 -48
36/4 -48
36/4 -36
36/4 -48
36/4 -48
36/4 -48
36/4 -48
36/4 -48
36/4 -48
36/4 -48
36/4 -42
36/4 -36
36/4 -24
36/4 -20
116 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
612
651
36/5 -14
36/4 -18
36/3 -16
36/3 -18
36/9 -48
36/4 -14
36/4 -24
36/9 -30
36/4 -12
36/4 -18
655
697
36/5 -10
36/4 -14
36/4 -24
36/3 -14
36/5 -8
36/5 -20
36/4 -20
36/9 -20
36/5 -18
36/4 -14
1 Tabulated
diaphragm
values
attachment
of
steel
base
from 3/16"
3/8". For
to base
333
354 shear36/3
-30are for36/3
-48
36/3
-48deck to36/3
-48steel thicknesses
36/3 -18 ranging
36/4 -48
36/4to-48
36/4attachment
-24
36/4
-48
steel thicknesses less than 3/16", diaphragm shear values for the X-EDNK22 fasteners should be calculated in accordance with Section 1.1.8 of
356
379
36/3
-24
36/3
-48
36/3
-48
36/3
-48
36/4
-30
36/4
-48
36/4
-48
36/4
-20
36/4
-48
this Product Technical Guide Supplement.
381
36/3
-48
36/3a-48
36/3 -48
36/4
36/4 -48
36/4ASD
-48 values
36/4for-18
36/4 -48
2 Tabulated
ASD 406
diaphragm 36/3
shear-18
loads are
calculated
with
safety factor
() of 2.35
for-24
wind loads.
To calculate
load combinations
involving
safety
() of-18
2.50. Panel
buckling36/4
has been
408 earthquake,
434 multiply
36/3values
-14 in table
36/3 by
-422.35 and
36/3divide
-48 by a36/3
-48factor 36/4
36/4 -48
-48 checked.
36/4 -14
36/4 -48
3 At437
diaphragm perimeter,
Hilti
frame
should be36/3
spaced
as -14
sidelap connectors.
464
36/4
-20 fasteners
36/3 -30
-48 at identical
36/3 -48spacing36/4
36/4 -42
36/4 -48
36/4 -12
36/4 -36
Figure
19:
Excerpt
of 36/3
Optimized
Diaphragm
Shear
Tabledeck-16gauge.36/4 -24
4 Interpolation of diaphragm shear strengths
and
factors is
between span
sidelap
spacings
467
497
36/4 -18
36/3
-20stiffness
36/3
-48 allowed
-48
36/4 -12dimensions,
36/4 -30
36/4
-48 and36/5
Alternatively, use calculations as discussed in Section 1.1.8 to determine diaphragm shear strengths and stiffness factors directly.
500
532
36/4 -14
36/3 -18
36/3 -36
36/3 -42
36/5 -18
36/4 -24
36/4 -48
36/5 -14
36/4 -20
5 To convert from sidelap spacing (SS) to sidelaps per span (SPS), use the following formula: SPS=((span, ft) x 12)/(SS, in.). Round up to the next
535 sidelap connector.
569
36/4 -12
36/4 -24
36/3 -24
36/3 -30
36/5 -14
36/4 -20
36/4 -42
36/9 -48
36/4 -18
whole
572
609 use S-SLC
36/502-16M HWH.
36/4More
-20 information
36/3 -20on Hilti36/3
-24 Connectors
36/5 -12(SLC) 36/4
-16found 36/4
-30 1.4.36/9 -48
36/4 -14
6 For
18 gauge deck
Sidelap
can be
in Section
152 mm
9
152 mm
Fastener
Material
Carbon Steel
Carbon Steel
Fastener
Plating
5 m Zinc1
5 m Zinc1
Nominal Fastener
Hardness
55 HRC
55 HRC
1 ASTM B633, SC 1, Type III. Reference Section 2.3.3.1 for more information.
Allowable Pullout Loads for Attachments to Steel Base Material lb (kN)1, 2, 3,4
Fastener
X-EDN19 THQ12
X-EDNK22 THQ12
1
2
3
4
1/8
435 (1.95)
3/8
540 (2.42)
3.5.2.1
Product Description
3.5.2.2
Material Specifications
3.5.2.3
Technical Data
3.5.2.4
Ordering Information
X-EDN19 THQ12M
X-EDNK22 THQ12M
Approvals/Listings
ICC-ES (International Code Council)
ESR-2776, ESR-2197, ESR-1735P,
ESR-1414
COLA (City of Los Angeles)
RR 25877, RR 25296
FM (Factory Mutual)
For attaching Class 1 Steel Roof Decks
with 1-60 and 1-90 wind uplift ratings.
Listed for higher wind uplift ratings with
FM Approved Lightweight Insulating
Concrete Roof Deck Assemblies.
Refer to FM RoofNav for specific
assembly listings.
UL (Underwriters Laboratories)
Fasteners for attaching steel roof deck
(uplift and fire classification)
ABS (American Bureau of Shipping)
Allowable Pullover and Shear Bearing Loads for Attaching Steel Deck 3,4,5
Fastener
X-EDN19 THQ12 1
X-EDNK22 THQ12 2
1
2
3
4
5
16 (0.0598)
Tension Shear
lb (kN)
lb (kN)
725
975
(3.19)
(4.29)
18 (0.0474)
Tension Shear
lb (kN)
lb (kN)
575
785
(2.53)
(3.45)
24 (0.0239)
Tension Shear
lb (kN)
lb (kN)
325
410
(1.43)
(1.80)
26 (0.0179)
Tension Shear
lb (kN)
lb (kN)
235
310
(1.03)
(1.36)
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 117
6''
36''
6''
1-1/2''
36''
152 mm
1-1/2''
914 mm
38 mm
36/9
6''
36''
6''
1-1/2''
914/9
36''
152 mm
1-1/2''
914 mm
38 mm
Allowable Stress Design (ASD)- Allowable Diaphragm Shears, SASD, (plf) and Stiffness Factors, G', (kips/in.) for
Standard 1-1/2" Deep Flutes, 6" Center-to-Center Steel Deck (Fy 33 ksi; Fu 45 ksi) Installed with Hilti X-EDN19
or X-EDNK22 Fasteners with 36/9 or 36/7 End and Interior Support Fastener Patterns1,2,3,4
Gauge
Sidelap
Spacing
Hilti SLC5,6,7
36" O.C.
24" O.C.
22
18" O.C.
12" O.C.
6" O.C.
36" O.C.
24" O.C.
20
18" O.C.
12" O.C.
6" O.C.
36" O.C.
24" O.C.
18
18" O.C.
12" O.C.
6" O.C.
Factor
5'-0"
6'-0"
S6''
ASD
7'-0"
8'-0"
9'-0"
36/9
Fasteners Per Sheet To
Support
36/11
10'-0"
914/11
715
499
612
431
529
378
467
341
6''
421152 mm
313
388
292
363
277
36'' 51.9
48.5
56.4 1-1/2''
52.0
59.2
54.1
60.9
55.4 36''
62.1
56.2
1-1/2''
mm 62.9
62.5 714
56.5
SASD
765
554
666
489
596
444
534
408
488
380
455
360
430
344
G'
52.9
50.2
58.1
54.5
61.6
57.5
64.1
59.6
65.8
61.0
67.1
62.1
68.0
62.9
G'
56.5 38 mm
SASD
813
607
719
545
651
501
601
469
555
445
522
426
497
410
G'
53.8
51.5
59.5
56.5
63.7
60.2
66.7
62.9
69.0
64.9
70.9
66.7
71.9
68.0
SASD
903
706
817
649
755
610
708
580
672
558
643
540
620
526
G'
55.2
53.5
61.7
59.6
66.7
64.3
70.7
70.9
76.3
73.5
78.7
75.8
SASD
1123
941
1060
902
1014
874
980
68.136/11
74.1
853
952
837
931
824
760
760
G'
57.9
57.0
65.8
64.8
72.3
71.2
77.7
76.5
82.6
81.3
86.2
84.7
90.1
88.5
SASD
948
668
815
581
715
517
635
468
575
36''
432
528
403
1-1/2''
495
383
G'
71.9
66.1
75.9
68.9
77.9
70.1
78.7
70.4
78.8
70.3
78.7
69.9
78.1
69.4
SASD
1021
749
894
665
804
607
734
564
673
530
627
502
593
481
G'
73.7
68.8
78.7
72.9
81.7
75.3
83.5
76.7
84.5
77.5
84.7
78.1
85.5
78.1
SASD
1090
825
970
745
883
690
819
649
769
618
725
594
692
574
G'
75.2
70.9
81.3
76.3
84.7
79.4
87.7
82.0
89.3
83.3
90.9
84.7
91.7
85.5
SASD
1218
964
1110
894
1032
844
973
808
927
779
891
757
861
739
G'
77.7
74.6
84.8
81.2
90.0
86.1
93.9
89.7
96.8
92.6
99.0
95.2
101.0
97.1
SASD
1522
1288
1447
1241
1392
1208
1350
1183
1317
1164
1222
1149
990
990
G'
82.5
80.9
91.9
90.2
99.4
97.5
105.4
103.4
110.4
108.4
114.9
112.4
117.6
116.3
6''
SASD
1171
831
1010
724
895
651
800
593
726
548
669
513
623
485
G'
109.9
99.0
111.5
98.7
110.9
97.4
109.3
95.7
107.3
93.8
105.2
91.7
103.1
90.1
SASD
1266
935
1112
833
1003
763
921
712
855
672
798
641
752
614
G'
113.6
104.2
116.8
105.9
117.7
106.3
117.5
106.0
116.6
105.3
115.5
104.4
114.9
103.1
SASD
1355
1033
1210
937
1106
870
1028
821
968
784
920
754
881
730
G'
117.6
108.7
122.0
112.4
123.5
113.6
125.0
114.9
125.0
114.9
125.0
114.9
123.5
114.9
SASD
1519
1211
1390
1127
1296
1068
1226
1024
1171
991
1128
964
1092
942
G'
122.0
116.3
128.9
121.7
133.1
125.7
135.8
128.3
137.6
130.2
138.8
131.6
138.9
133.3
SASD
1519
1211
1390
1145
1296
1106
1243
1077
1205
1054
1175
1037
1150
1022
G'
133.3
129.9
143.6
139.9
151.5
147.6
157.5
153.6
162.2
158.4
166.0
162.4
169.5
166.7
1 Tabulated diaphragm shear values are for attachment of steel deck to base steel thicknesses ranging from 3/16" to 3/8". For attachment to base steel
thicknesses less than 3/16", diaphragm shear values for the X-EDNK22 fasteners should be calculated in accordance with Section 3.5.1.8.
2 Tabulated ASD diaphragm shear loads are calculated with a safety factor () of 2.35 for wind loads. To calculate ASD values for load combinations involving
earthquake, multiply values in table by 2.35 and divide by a safety factor () of 2.50. Panel buckling has been checked.
3 At diaphragm perimeter, Hilti frame fasteners should be spaced at identical spacing as sidelap connectors.
4 Interpolation of diaphragm shear strengths and stiffness factors is allowed between span dimensions, sidelap spacings and deck gauge. Alternatively, use
calculations as discussed in Section 3.5.1.8 to determine diaphragm shear strengths and stiffness factors directly.
5 To convert from sidelap spacing (SS) to sidelaps per span (SPS), use the following formula: SPS=((span, ft) x 12)/(SS, in.). Round up to the next whole
sidelap connector.
6 For high tensile strength (fu > 65 ksi) 18 gauge steel deck, use S-SLC 02 M HWH. More information on Hilti Sidelap Connectors (SLC) can be found in
Section 3.5.4.
7 For diaphragm shear load values using Hilti #10 HWH screws, use the Hilti Profis DF Diaphragm software or contact Hilti at 877-749-6337 or deck@hilti.com.
118 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
6''
36''
6'' 152 mm
36''
1-1/2''
1-1/2''
914 mm
38 mm
36/5
6''
36''
914/5
6'' 152 mm
36''
1-1/2''
1-1/2''
914 mm
38 mm
Allowable Stress Design (ASD)- Allowable Diaphragm Shears, SASD, (plf) and Stiffness Factors, G', (kips/in.) for
Standard 1-1/2" Deep Flutes, 6" Center-to-Center Steel Deck (Fy 33 ksi; Fu 45 ksi) Installed with Hilti X-EDN19
or X-EDNK22 Fasteners with 36/5 or 36/4 End and Interior Support Fastener Patterns1,2,3,4
Gauge
Sidelap
Spacing
Hilti SLC5,6,7
36" O.C.
24" O.C.
22
18" O.C.
12" O.C.
6" O.C.
36" O.C.
24" O.C.
20
18" O.C.
12" O.C.
6" O.C.
36" O.C.
24" O.C.
18
18" O.C.
12" O.C.
6" O.C.
Factor
5'-0"
6'-0"
36/7
S
6''
ASD
G'
8'-0"
9'-0"
36/5
Fasteners Per Sheet To Support
7'-0"
914/7
448
365
393
325
354
296
325
275
18.1
13.4
20.1
15.1
36'' 13.2
9.7
15.81-1/2''
11.6
299
257
6'' 152 mm
21.9 36''16.6
10'-0"
280
242
265
232
1-1/2''
mm
23.5 914
18.0
24.9
19.3 38 mm
SASD
495
407
444
372
408
346
380
327
359
312
343
300
329
290
G'
13.4
9.8
16.1
11.8
18.5
13.7
20.7
15.5
22.7
17.2
24.6
18.8
26.2
20.2
SASD
537
445
491
414
457
391
432
374
412
360
397
350
384
341
G'
13.5
9.8
16.3
12.0
18.8
14.0
21.2
15.8
23.4
17.6
25.4
19.3
27.2
20.9
SASD
612
508
573
484
545
466
524
453
507
442
494
434
483
427
G'36/9 13.7
9.9
16.6
12.1
19.3
14.2
21.8
16.2
24.2
36/7 18.1
26.4
914/920.0
28.5
21.7
SASD
766
623
744
611
729
603
717
597
707
592
700
588
694
585
G'
6''
13.9
10.1
17.0
12.4
19.9
14.6
22.7
16.8
25.3
6''
18.8
27.9
20.8
30.3
22.8
1-1/2''
387 914
338
368
mm
324 38 mm
G'
20.4
31.6
24.5
33.4
27.8
490
530 1-1/2''
439
479
403
442
376
15.0
23.9
26.9
20.3
29.4
22.5
17.8
152 mm
413 36''355
26.2
35.1
SASD
666
550
602
506
556
474
522
450
495
431
474
416
456
404
G'
20.7
15.2
24.4
18.2
27.8
21.0
30.7
23.4
33.3
25.7
35.6
27.7
37.6
29.6
SASD
727
603
668
564
626
536
595
515
570
499
551
485
535
475
G'
20.9
15.4
24.9
18.5
28.4
21.4
31.6
24.0
34.5
26.5
37.0
28.8
39.5
30.9
36/11 830
SASD
G'
21.3
SASD
830
6''
688
783
659
748
638
722
622
15.6
25.5
18.9
29.3
22.0
32.9
24.9
688
783
659
748
638
722
16.0
26.41-1/2''
19.5
30.7
22.8
34.7
70236/9 610
673
592
39.1
686
600
914/11
30.1
41.8
32.6
686
600
673
36.1
27.6
622
702
610
26.0
42.0 714
31.9
45.5
mm1-1/2''
492
427
467
34.8 38 mm
411
44.6
6'' 152 mm
592
609
660
549
599
505
554
473
38.5 36''29.1
519
447
G'
36.8
27.6
41.7
31.9
45.7
35.5
48.8
38.4
51.0
40.9
52.9
42.9
54.6
SASD
830
687
753
634
698
596
657
567
624
545
599
527
578
512
G'
37.6
28.2
43.3
33.1
47.8
37.2
51.8
40.8
54.9
43.9
57.8
46.6
59.9
49.0
SASD
907
753
838
708
788
675
750
650
721
631
698
615
678
602
G'
38.3
28.8
44.4
33.9
49.8
38.5
54.1
42.4
57.8
46.1
61.3
49.3
64.1
52.1
SASD
907
753
838
708
788
675
750
650
721
631
698
615
678
602
G'
39.4
29.5
46.1
35.1
52.1
40.2
57.5
44.8
62.1
48.9
66.2
52.8
69.9
56.2
SASD
985
804
954
788
932
776
914
766
G'
41.0
30.6
48.8
36.8
55.9
42.6
62.5
48.0
901 36''759
68.5
53.1
73.5
754 1-1/2''
881
78.7
62.1
36/11
6''
890
57.8
749
1 Tabulated diaphragm shear values are for attachment of steel deck to base steel thicknesses ranging from 3/16" to 3/8". For attachment to base steel
thicknesses less than 3/16", diaphragm shear values for the X-EDNK22 fasteners should be calculated in accordance with Section 3.5.1.8.
2 Tabulated ASD diaphragm shear loads are calculated with a safety factor () of 2.35 for wind loads. To calculate ASD values for load combinations involving
earthquake, multiply values in table by 2.35 and divide by a safety factor () of 2.50. Panel buckling has been checked.
3 At diaphragm perimeter, Hilti frame fasteners should be spaced at identical spacing as sidelap connectors.
4 Interpolation of diaphragm shear strengths and stiffness factors is allowed between span dimensions, sidelap spacings and deck gauge. Alternatively, use
calculations as discussed in Section 3.5.1.8 to determine diaphragm shear strengths and stiffness factors directly.
5 To convert from sidelap spacing (SS) to sidelaps per span (SPS), use the following formula: SPS=((span, ft) x 12)/(SS, in.). Round up to the next whole
sidelap connector.
6 For high tensile strength (fu > 65 ksi) 18 gauge steel deck, use S-SLC 02 M HWH. More information on Hilti Sidelap Connectors (SLC) can be found in
Section 3.5.4.
7 For diaphragm shear load values using Hilti #10 HWH screws, use the Hilti Profis DF Diaphragm software or contact Hilti at 877-749-6337 or deck@hilti.com.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 119
6''
36''
6''
1-1/2''
36''
152 mm
1-1/2''
914 mm
38 mm
36/9
6''
36''
6''
1-1/2''
914/9
36''
152 mm
1-1/2''
914 mm
Load Resistance Factor Design (LRFD)- Factored Resistance Diaphragm Shears, SLRFD, (plf) and Stiffness Factors, G',
(kips/in.) for Standard 1-1/2" Deep Flutes, 6" Center-to-Center Steel Deck (Fy 33 ksi; Fu 45 ksi) Installed with Hilti
X-EDN19 or X-EDNK22 Fasteners with 36/9 or 36/7 End and Interior Support Fastener Patterns1,2,3,4
Gauge
Sidelap
Spacing
Hilti SLC5,6,7
36" O.C.
24" O.C.
22
18" O.C.
12" O.C.
6" O.C.
36" O.C.
24" O.C.
20
18" O.C.
12" O.C.
6" O.C.
36" O.C.
24" O.C.
18
18" O.C.
12" O.C.
6" O.C.
38 mm
Factor
5'-0"
6'-0"
S6''
LRFD
7'-0"
8'-0"
9'-0"
36/11
10'-0"
914/11
1174
820
1005
708
869
622
768
560
6''
692152 mm
514
638
481
596
455
36'' 51.9
48.5
56.4 1-1/2''
52.0
59.2
54.1
60.9
55.4 36''
62.1
56.2
1-1/2''
mm 62.9
62.5 714
56.5
SLRFD
1257
911
1095
803
979
729
878
671
802
624
748
591
706
565
G'
52.9
50.2
58.1
54.5
61.6
57.5
64.1
59.6
65.8
61.0
67.1
62.1
68.0
62.9
SLRFD
1336
998
1181
895
1070
824
987
771
912
731
858
700
817
674
G'
53.8
51.5
59.5
56.5
63.7
60.2
66.7
62.9
69.0
64.9
70.9
66.7
71.9
68.0
SLRFD
1484
1159
1342
1067
1240
1002
1164
954
1104
917
1057
888
1019
864
G'
55.2
53.5
61.7
59.6
66.7
64.3
70.7
70.9
76.3
73.5
78.7
75.8
SASD
1846
1547
1742
1482
1667
1436
1610
68.136/11
74.1
1402
1565
1375
1501
1354
1216
1216
G'
57.9
57.0
65.8
64.8
72.3
71.2
77.7
76.5
82.6
81.3
86.2
84.7
90.1
88.5
SLRFD
1558
1098
1339
954
1175
850
1044
770
945
36''
710
868
663
1-1/2''
813
629
G'
71.9
66.1
75.9
68.9
77.9
70.1
78.7
70.4
78.8
70.3
78.7
69.9
78.1
69.4
SLRFD
1678
1230
1469
1093
1321
997
1206
927
1107
872
1030
825
975
791
G'
73.7
68.8
78.7
72.9
81.7
75.3
83.5
76.7
84.5
77.5
84.7
78.1
85.5
78.1
SLRFD
1791
1355
1593
1225
1451
1134
1346
1067
1264
1016
1192
975
1137
943
G'
75.2
70.9
81.3
76.3
84.7
79.4
87.7
82.0
89.3
83.3
90.9
84.7
91.7
85.5
SLRFD
2001
1585
1823
1469
1695
1387
1599
1327
1524
1281
1464
1244
1415
1214
G'
77.7
74.6
84.8
81.2
90.0
86.1
93.9
89.7
96.8
92.6
99.0
95.2
101.0
97.1
SLRFD
2501
2116
2377
2039
2287
1985
2218
1944
2165
1913
1956
1888
1584
1584
116.3
G'
6''
56.5 38 mm
G'
82.5
80.9
91.9
90.2
99.4
97.5
105.4
103.4
110.4
108.4
114.9
112.4
117.6
SLRFD
1925
1365
1660
1190
1471
1069
1314
974
1193
900
1099
843
1024
797
G'
109.9
99.0
111.5
98.7
110.9
97.4
109.3
95.7
107.3
93.8
105.2
91.7
103.1
90.1
SLRFD
2080
1536
1828
1370
1648
1254
1514
1169
1405
1105
1311
1053
1236
1009
G'
113.6
104.2
116.8
105.9
117.7
106.3
117.5
106.0
116.6
105.3
115.5
104.4
114.9
103.1
SLRFD
2227
1697
1988
1540
1817
1430
1689
1350
1590
1288
1511
1239
1447
1200
G'
117.6
108.7
122.0
112.4
123.5
113.6
125.0
114.9
125.0
114.9
125.0
114.9
123.5
114.9
SLRFD
2496
1990
2283
1852
2130
1755
2014
1683
1925
1628
1853
1584
1795
1549
G'
122.0
116.3
128.9
121.7
133.1
125.7
135.8
128.3
137.6
130.2
138.8
131.6
138.9
133.3
SLRFD
2496
1990
2283
1881
2130
1817
2042
1769
1980
1733
1931
1703
1890
1679
G'
133.3
129.9
143.6
139.9
151.5
147.6
157.5
153.6
162.2
158.4
166.0
162.4
169.5
166.7
1 Tabulated diaphragm shear values are for attachment of steel deck to base steel thicknesses ranging from 3/16" to 3/8". For attachment to base steel
thicknesses less than 3/16", diaphragm shear values for the X-EDNK22 fasteners should be calculated in accordance with Section 3.5.1.8.
2 Tabulated LRFD diaphragm shear loads are calculated with a phi factor () of 0.70 for wind loads. To calculate LRFD values for load combinations involving
earthquake, divide values in table by 0.70 and multiply by a phi factor () of 0.65. Panel buckling has been checked.
3 At diaphragm perimeter, Hilti frame fasteners should be spaced at identical spacing as sidelap connectors.
4 Interpolation of diaphragm shear strengths and stiffness factors is allowed between span dimensions, sidelap spacings and deck gauge. Alternatively, use
calculations as discussed in Section 3.5.1.8 to determine diaphragm shear strengths and stiffness factors directly.
5 To convert from sidelap spacing (SS) to sidelaps per span (SPS), use the following formula: SPS=((span, ft) x 12)/(SS, in.). Round up to the next whole
sidelap connector.
6 For high tensile strength (fu > 65 ksi) 18 gauge steel deck, use S-SLC 02 M HWH. More information on Hilti Sidelap Connectors (SLC) can be found in
Section 3.5.4.
7 For diaphragm shear load values using Hilti #10 HWH screws, use the Hilti Profis DF Diaphragm software or contact Hilti at 877-749-6337 or deck@hilti.com.
120 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
6''
36''
6'' 152 mm
36''
1-1/2''
1-1/2''
914 mm
38 mm
36/5
6''
36''
914/5
6'' 152 mm
36''
1-1/2''
1-1/2''
914 mm
38 mm
Load Resistance Factor Design (LRFD)- Factored Resistance Diaphragm Shears, SLRFD, (plf) and Stiffness Factors, G',
(kips/in.) for Standard 1-1/2" Deep Flutes, 6" Center-to-Center Steel Deck (Fy 33 ksi; Fu 45 ksi) Installed with Hilti
X-EDN19 or X-EDNK22 Fasteners with 36/5 or 36/4 End and Interior Support Fastener Patterns1,2,3,4
Gauge
Sidelap
Spacing
Hilti SLC5,6,7
36" O.C.
24" O.C.
22
18" O.C.
12" O.C.
6" O.C.
24" O.C.
20
18" O.C.
12" O.C.
6" O.C.
36" O.C.
24" O.C.
18
18" O.C.
12" O.C.
6" O.C.
5'-0"
6'-0"
36/7
S6''
LRFD
8'-0"
9'-0"
7'-0"
914/7
737
599
646
534
582
487
534
452
10'-0"
460
398
436
1-1/2''
mm
23.5 914
18.0
24.9
381
36'' 13.2
9.7
15.81-1/2''
11.6
18.1
13.4
20.1
15.1
491
422
6'' 152 mm
21.9 36''16.6
SLRFD
813
669
729
611
670
569
625
537
590
513
563
493
540
477
G'
13.4
9.8
16.1
11.8
18.5
13.7
20.7
15.5
22.7
17.2
24.6
18.8
26.2
20.2
SLRFD
883
732
806
680
751
643
710
614
678
592
652
574
631
560
G'
13.5
9.8
16.3
12.0
18.8
14.0
21.2
15.8
23.4
17.6
25.4
19.3
27.2
20.9
SLRFD
1006
835
942
795
896
766
861
744
833
726
811
712
793
701
G'36/9 13.7
9.9
16.6
12.1
19.3
14.2
21.8
16.2
24.2
36/7 18.1
26.4
914/920.0
28.5
21.7
G'
19.3 38 mm
SASD
1259
1023
1223
1005
1197
991
1178
981
1162
973
1150
967
1140
962
G'
13.9
10.1
17.0
12.4
19.9
14.6
22.7
16.8
25.3
18.8
27.9
20.8
30.3
22.8
805
870 1-1/2''
722
788
662
727
618
679 36''583
15.0
23.9
26.9
20.3
29.4
22.5
31.6
636 914
556
605
1-1/2''
mm
26.2
35.1
27.8
6''
36" O.C.
4'-0"
6'' 152 mm
532 38 mm
G'
20.4
SLRFD
1095
904
989
831
914
779
857
739
813
708
778
684
750
663
G'
20.7
15.2
24.4
18.2
27.8
21.0
30.7
23.4
33.3
25.7
35.6
27.7
37.6
29.6
SLRFD
1194
991
1098
928
1029
882
977
847
937
820
905
798
878
780
G'
20.9
15.4
24.9
18.5
28.4
21.4
31.6
24.0
34.5
26.5
37.0
28.8
39.5
30.9
SLRFD
1364
1131
1286
1083
1230
1049
1187
1023
1154
986
1105
972
21.3
15.6
25.5
18.9
29.3
22.0
32.9
24.9
36/91002
1127
G'
36.1
27.6
39.1
30.1
41.8
32.6
SLRFD
1364
1131
1286
1083
1230
1049
1187
1023
1154
1002
1127
986
1105
16.0
26.41-1/2''
19.5
30.7
22.8
34.7
26.0
38.5 36''29.1
853
735
42.0 714
31.9
45.5
mm1-1/2''
808
702
768
34.8 38 mm
675
44.6
36/11
6''
17.8
24.5
6'' 152 mm
33.4
914/11
972
1001
1084
902
985
830
911
777
G'
36.8
27.6
41.7
31.9
45.7
35.5
48.8
38.4
51.0
40.9
52.9
42.9
54.6
SLRFD
1364
1128
1238
1042
1147
979
1079
932
1026
895
984
866
950
842
G'
37.6
28.2
43.3
33.1
47.8
37.2
51.8
40.8
54.9
43.9
57.8
46.6
59.9
49.0
SLRFD
1490
1238
1377
1163
1295
1109
1233
1068
1185
1036
1146
1010
1115
989
G'
38.3
28.8
44.4
33.9
49.8
38.5
54.1
42.4
57.8
46.1
61.3
49.3
64.1
52.1
SLRFD
1490
1238
1377
1163
1295
1109
1233
1068
1185
1036
1146
1010
1115
989
G'
39.4
29.5
46.1
35.1
52.1
40.2
57.5
44.8
62.1
48.9
66.2
52.8
69.9
56.2
SLRFD
1619
1321
1568
1294
1531
1274
1503
1259
1480
1248
1463
1238
1448
1230
G'
41.0
30.6
48.8
36.8
55.9
42.6
62.5
48.0
68.5
53.1
73.5
57.8
78.7
62.1
36/11
6''
36''
1-1/2''
1 Tabulated diaphragm shear values are for attachment of steel deck to base steel thicknesses ranging from 3/16" to 3/8". For attachment to base steel
thicknesses less than 3/16", diaphragm shear values for the X-EDNK22 fasteners should be calculated in accordance with Section 3.5.1.8.
2 Tabulated LRFD diaphragm shear loads are calculated with a phi factor () of 0.70 for wind loads. To calculate LRFD values for load combinations involving
earthquake, divide values in table by 0.70 and multiply by a phi factor () of 0.65. Panel buckling has been checked.
3 At diaphragm perimeter, Hilti frame fasteners should be spaced at identical spacing as sidelap connectors.
4 Interpolation of diaphragm shear strengths and stiffness factors is allowed between span dimensions, sidelap spacings and deck gauge. Alternatively, use
calculations as discussed in Section 3.5.1.8 to determine diaphragm shear strengths and stiffness factors directly.
5 To convert from sidelap spacing (SS) to sidelaps per span (SPS), use the following formula: SPS=((span, ft) x 12)/(SS, in.). Round up to the next whole
sidelap connector.
6 For high tensile strength (fu > 65 ksi) 18 gauge steel deck, use S-SLC 02 M HWH. More information on Hilti Sidelap Connectors (SLC) can be found in
Section 3.5.4.
7 For diaphragm shear load values using Hilti #10 HWH screws, use the Hilti Profis DF Diaphragm software or contact Hilti at 877-749-6337 or deck@hilti.com.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 121
6''
914 mm
1-1/2''
36''
152 mm
38 mm
914 mm
38 mm
914/9
(36/9)
914/9
6'' 152 mm
36''
914/7
(36/7)
914/7
914 mm
1-1/2''
152 mm
38 mm
914 mm
38 mm
Limit States Design (LSD)- Factored Resistance Diaphragm Shears, SLSD, (N/mm) and Stiffness Factors, G', (103 N/mm)
for Standard 38 mm Deep Flutes, 152 mm Center-to-Center Steel Deck (Fy 230 MPa; Fu 310 MPa) Installed with Hilti
X-EDN19 or X-EDNK22 Fasteners with 914/9 (36/9) or 914/7 (36/7) End and Interior Support Fastener Patterns1,2,3,4
Gauge
Sidelap
Spacing
36/9
Hilti SLC5,6,7
6'' 152 mm
900 mm O.C.
36''
600 mm O.C.
22
450 mm O.C.
300 mm O.C.
36/11
150 mm O.C.
6''
36''
900 mm O.C.
600 mm O.C.
20
450 mm O.C.
300 mm O.C.
150 mm O.C.
900 mm O.C.
600 mm O.C.
18
450 mm O.C.
300 mm O.C.
150 mm O.C.
Span (mm)
1200
Factor
914/11
SLSD
G'
SLSD
1500
1800
2100
2400
2700
3000
914/9
Fasteners Per Sheet To Support
9
16.1
11.3
13.8
9.7
12.0
8.6
10.3
17.3
12.5
15.0
11.0
13.5
714 9.0
mm
1-1/2''
8.5
9.8 38 mm
9.1
9.5
7.1
8.8
6.6
8.2
6.3
9.5
10.6
7.7
152 mm
10.7
9.7
mm
10.9 9149.8
11.0
9.9 38 mm
11.0
9.9
10.0
12.1
11.1
10.3
8.1
9.7
7.8
11.0
9.2
8.6
G'
9.2
8.7
10.1
9.5
10.8
10.1
11.2
10.4
11.5
10.8
11.8
10.9
11.9
SLSD
18.3
13.7
16.2
12.3
14.7
11.3
13.6
10.6
12.6
10.1
11.8
9.6
11.2
9.3
G'
9.3
8.9
10.3
9.9
11.1
10.5
11.6
11.0
12.0
11.4
12.3
11.8
12.7
11.9
SLSD
20.3
15.9
18.4
14.6
17.0
13.8
16.0
13.1
15.2
12.6
14.5
12.2
14.0
11.9
G'
9.6
9.3
10.7
10.4
11.6
11.2
12.3
11.9
13.3
12.8
13.7
13.3
SLSD
25.3
21.2
23.9
20.3
22.8
19.7
22.1
19.2
12.8
914/1112.5
21.0
18.6
17.2
17.2
10.0
15.6
15.4
G'
18.8
14.3
14.1
9.9
11.4
11.3
12.6
12.4
13.5
15.2
14.9
21.41-1/2''
15.1
18.4
13.1
16.2
11.7
14.4
10.6
13.0 7149.8
mm
12.0
9.1 38 mm
11.2
8.7
G'
12.5
11.5
13.3
12.1
13.6
12.3
13.8
12.4
13.8
12.4
13.8
12.3
13.8
12.2
SLSD
23.0
16.9
20.2
15.0
18.1
13.7
16.6
12.8
15.3
12.0
14.2
11.4
13.4
10.9
G'
12.8
12.0
13.7
12.7
14.3
13.2
14.6
13.5
14.8
13.6
14.8
13.7
14.8
13.7
SLSD
24.6
18.6
21.9
16.8
19.9
15.6
18.5
14.7
17.4
14.0
16.4
13.4
15.7
13.0
SLSD
13.3
152 mm
21.4
G'
13.2
12.3
14.1
13.3
14.9
13.9
15.4
14.3
15.6
14.7
15.9
14.9
16.1
14.9
SLSD
27.4
21.7
25.0
20.2
23.3
19.0
21.9
18.2
20.9
17.6
20.1
17.1
19.4
16.7
G'
13.5
13.0
14.8
14.2
15.7
15.0
16.4
15.7
17.0
16.2
17.2
16.7
17.9
16.9
SLSD
34.0
28.8
32.3
27.7
31.1
27.0
30.2
26.4
29.4
26.0
27.6
25.6
22.4
22.4
G'
14.4
14.1
16.0
15.7
17.3
17.0
18.4
18.1
19.3
18.9
20.0
19.6
20.8
20.4
SLSD
26.4
18.8
22.8
16.4
20.2
14.7
18.1
13.4
16.4
12.4
15.2
11.6
14.1
11.0
G'
19.2
17.3
19.6
17.3
19.5
17.2
19.2
16.9
18.9
16.5
18.5
16.2
18.2
15.9
SLSD
28.5
21.1
25.1
18.8
22.6
17.2
20.8
16.1
19.4
15.2
18.1
14.5
17.0
13.9
G'
20.0
18.2
20.5
18.6
20.7
18.7
20.7
18.7
20.5
18.5
20.4
18.4
20.0
18.2
SLSD
30.5
23.3
27.3
21.2
25.0
19.7
23.2
18.5
21.8
17.7
20.8
17.0
19.9
16.5
G'
20.4
18.9
21.3
19.6
21.7
20.0
21.7
20.0
21.7
20.4
21.7
20.4
21.7
20.4
SLSD
34.0
27.1
31.1
25.2
29.0
23.9
27.5
22.9
26.2
22.2
25.2
21.5
24.4
21.1
G'
21.3
20.4
22.6
21.3
23.3
22.1
23.8
22.5
24.2
22.9
24.4
23.2
24.4
23.3
SLSD
34.0
27.1
31.1
25.6
29.0
24.7
27.8
24.0
26.9
23.5
26.2
23.1
25.7
22.8
G'
23.3
22.7
25.1
24.5
26.5
25.8
27.6
26.9
28.4
27.8
29.1
28.5
29.4
29.4
1 Tabulated diaphragm shear values are for attachment of steel deck to base steel thicknesses ranging from 5 mm to 10 mm. For attachment to base steel
thicknesses less than 5 mm, diaphragm shear values for the X-EDNK22 fasteners should be calculated in accordance with Section 3.5.1.8.
2 Tabulated LSD diaphragm shear loads are calculated with a phi factor () of 0.65 for wind loads. To calculate LSD values for load combinations involving
earthquake, divide values in table by 0.65 and multiply by a phi factor () of 0.60. Panel buckling has been checked.
3 At diaphragm perimeter, Hilti frame fasteners should be spaced at identical spacing as sidelap connectors.
4 Interpolation of diaphragm shear strengths and stiffness factors is allowed between span dimensions, sidelap spacings and deck gauge. Alternatively, use
calculations as discussed in Section 3.5.1.8 to determine diaphragm shear strengths and stiffness factors directly.
5 To convert from sidelap spacing (SS) to sidelaps per span (SPS), use the following formula: SPS=(span, mm)/(SS, mm). Round up to the next whole
sidelap connector.
6 For high tensile strength (fu > 65 ksi) 18 gauge steel deck, use S-SLC 02 M HWH. More information on Hilti Sidelap Connectors (SLC) can be found in
Section 3.5.4.
7 For diaphragm shear load values using Hilti #10 HWH screws, use the Hilti Profis DF Diaphragm software or contact Hilti at 877-749-6337 or deck@hilti.com.
122 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
6''
914 mm
1-1/2''
36''
152 mm
38 mm
914 mm
38 mm
Steel Deck Fastening Systems
c
36/4
914/5
(36/5)
914/5
6'' 152 mm
36''
914/4
(36/4)
914/4
914 mm
1-1/2''
152 mm
38 mm
914 mm
38 mm
Limit States Design (LSD)- Factored Resistance Diaphragm Shears, SLSD, (N/mm) and Stiffness Factors, G', (103 N/mm)
for Standard 38 mm Deep Flutes, 152 mm Center-to-Center Steel Deck (Fy 230 MPa; Fu 310 MPa) Installed with Hilti
X-EDN19 or X-EDNK22 Fasteners with 914/5 (36/5) or 914/4 (36/4) End and Interior Support Fastener Patterns1,2,3,4
Gauge
Sidelap
Spacing
36/5
Hilti SLC5,6,7
152 mm
6''mm
900
O.C.
36''
600 mm O.C.
22
450 mm O.C.
300 mm O.C.
36/7
150 mm O.C.
6'' 152 mm
36''
900 mm O.C.
600 mm O.C.
20
450 mm O.C.
36/9
300 mm
O.C.
152O.C.
mm
150
6''mm
36''
900 mm O.C.
600 mm O.C.
18
450 mm O.C.
36/11
300 mm O.C.
6''
150 mm36''
O.C.
Span (mm)
1200
Factor
914/7
SLSD
G'
1500
2100
2400
2700
3000
914/5
Fasteners Per Sheet To Support
5
10.1
8.2
8.9
7.3
8.0
6.7
3.1
11.2
9.2
10.0
8.4
9.2
914 2.3
mm
1-1/2''
1.7
SLSD
1800
2.738 mm
2.0
6.8
5.8
6.3
5.5
6.0
5.2
2.3
7.3152 mm
6.2
3.5
2.6
mm
3.8 9142.9
4.1
3.1 38 mm
4.3
3.3
7.8
8.6
8.1
7.7
6.8
6.5
7.4
7.0
7.4
G'
2.3
1.7
2.8
2.0
3.2
2.4
3.6
2.7
3.9
3.0
4.3
3.3
4.6
3.5
SLSD
12.1
10.0
11.1
9.3
10.3
8.8
9.7
8.4
9.3
8.1
9.0
7.9
8.7
7.7
G'
2.3
1.7
2.8
2.1
3.3
2.4
3.7
2.7
4.0
3.0
4.4
3.3
4.7
3.6
SLSD
13.8
11.4
12.9
10.9
12.3
10.5
11.8
10.2
11.4
9.9
11.1
9.8
10.9
9.6
G'914/9 2.4
1.7
2.9
2.1
3.3
2.5
3.8
2.8
SLSD
17.1
13.9
16.6
13.6
16.3
13.4
16.0
13.3
G'
2.4
1.7
2.9
2.1
3.4
2.5
3.9
11.938 mm
9.9
10.8
9.1
10.0
11.0
SLSD 91413.5
mm
1-1/2''
2.9
152 mm
8.5
4.2
914/7 3.1
15.8
13.2
4.4
3.3
9.3 9148.0
mm
4.6
3.5
5.0
3.8
15.6
13.1
15.5
13.0
4.8
3.6
5.2
3.9
8.8
7.6 38 mm
8.3
7.3
G'
3.5
2.6
4.1
3.1
4.7
3.5
5.1
3.9
5.5
4.3
5.8
4.6
6.1
4.8
SLSD
15.0
12.4
13.6
11.4
12.5
10.7
11.8
10.1
11.2
9.7
10.7
9.4
10.3
9.1
G'
3.6
2.6
4.2
3.2
4.8
3.6
5.3
4.1
5.8
4.5
6.2
4.8
6.5
5.2
SLSD
16.4
13.6
15.1
12.7
14.1
12.1
13.4
11.6
12.9
11.2
12.4
10.9
12.1
10.7
G'
3.6
2.7
4.3
3.2
4.9
3.7
5.5
4.2
6.0
4.6
6.5
5.0
6.8
5.4
SLSD
18.6
15.4
17.5
14.7
16.7
14.3
16.2
13.9
15.7
13.6
15.3
13.4
15.0
13.2
G'
3.7
2.7
4.4
3.3
5.1
3.8
5.7
4.3
6.3
4.8
6.8
5.2
7.3
5.6
SLSD
18.6
15.4
17.5
14.7
16.7
14.3
16.1
13.9
15.7
13.6
15.3
13.4
15.0
13.2
4.6 38 mm
3.4
5.3
3.9
6.0
4.5
14.9
13.5
11.4
12.5
10.7
5.5 38 mm
7.9
10.6
9.3
914/11
G'
SLSD
2.8
714 3.8
mm
1-1/2''
16.8
13.7
12.4
152 mm
914/9
6.7 9145.0
mm
10.1
11.7
7.3
11.1
9.6
6.0
G'
6.4
4.8
7.2
5.5
7.9
6.2
8.5
6.7
8.9
7.1
9.3
7.5
9.5
7.8
SLSD
18.7
15.5
17.0
14.3
15.7
13.4
14.8
12.8
14.1
12.3
13.5
11.9
13.0
11.6
G'
6.5
4.9
7.5
5.7
8.3
6.5
9.0
7.1
9.6
7.6
10.1
8.1
10.5
8.5
SLSD
20.3
16.8
18.8
15.8
17.6
15.1
16.8
14.5
16.1
14.1
15.6
13.7
15.2
13.4
G'
6.6
5.0
7.7
5.9
8.6
6.7
9.4
7.4
10.1
8.0
10.6
8.5
11.2
9.1
SLSD
20.3
16.8
18.8
15.8
17.6
15.1
16.8
14.5
16.1
14.1
15.6
13.7
15.2
13.4
7.8
G'
6.8
5.1
8.0
6.1
9.1
7.0
10.0
SLSD
22.0
17.9
21.3
17.6
20.8
17.3
20.4
G'
7.1
5.3
8.5
6.4
9.7
7.4
10.9
1-1/2''
152 mm
17.1
8.3
914/11
10.8
8.5
11.5
9.2
12.2
9.8
20.1
16.9
19.8
16.8
19.6
16.7
9.2
12.8
10.0
13.7
10.8
11.9
714 mm
38 mm
1 Tabulated diaphragm shear values are for attachment of steel deck to base steel thicknesses ranging from 5 mm to 10 mm. For attachment to base steel
thicknesses less than 5 mm, diaphragm shear values for the X-EDNK22 fasteners should be calculated in accordance with Section 3.5.1.8.
2 Tabulated LSD diaphragm shear loads are calculated with a phi factor () of 0.65 for wind loads. To calculate LSD values for load combinations involving
earthquake, divide values in table by 0.65 and multiply by a phi factor () of 0.60. Panel buckling has been checked.
3 At diaphragm perimeter, Hilti frame fasteners should be spaced at identical spacing as sidelap connectors.
4 Interpolation of diaphragm shear strengths and stiffness factors is allowed between span dimensions, sidelap spacings and deck gauge. Alternatively, use
calculations as discussed in Section 3.5.1.8 to determine diaphragm shear strengths and stiffness factors directly.
5 To convert from sidelap spacing (SS) to sidelaps per span (SPS), use the following formula: SPS=(span, mm)/(SS, mm). Round up to the next whole
sidelap connector.
6 For high tensile strength (fu > 65 ksi) 18 gauge steel deck, use S-SLC 02 M HWH. More information on Hilti Sidelap Connectors (SLC) can be found in
Section 3.5.4.
7 For diaphragm shear load values using Hilti #10 HWH screws, use the Hilti Profis DF Diaphragm software or contact Hilti at 877-749-6337 or deck@hilti.com.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 123
Limit States Design-Factored Resistance Diaphragm Tables for Deck Fasteners (Canada)
Limit States Design (LSD)-Factored Resistance Diaphragm Shear, q, (N/mm) and Flexibility Factor, F, (mm x 10-6/N)
for 38 mm deep steel nestable deck fastened w/Hilti X-EDNK22/EDN19 w/screwed sidelaps (Canada only)1,2,3
Diaphragm Table 36-7 w/X-EDNK22/EDN19 Metric
No. of Transverse Nails per 900 mm Wide Deck Units=7 (every flute)
Span (mm)
1200
1500
1800
2100
2400
2700
3000
Sidelap Connection
Deck Gauge Thickness
Strength, SLSD
Flexibility Factor, F
Strength, SLSD
Flexibility Factor, F
Strength, SLSD
Flexibility Factor, F
Strength, SLSD
Flexibility Factor, F
Strength, SLSD
Flexibility Factor, F
Strength, SLSD
Flexibility Factor, F
Strength, SLSD
Flexibility Factor, F
#10 Screw at 600 mm O.C. #10 Screw at 450 mm O.C. #10 Screw at 300 mm O.C. #10 Screw at 150 mm O.C.
22
20
18
16
22
20
18
16
22
20
18
16
22
20
18
16
6.5
7.9
10.2 12.8
6.5
7.9
10.2 12.8
8.3
10.1 13.3 16.7 11.6 14.0 18.4 23.1
120
88
60
45
120
88
60
45
110
79
52
38
101
71
45
32
5.2
6.2
8.2
10.3
6.1
7.4
9.6
12.1
7.6
9.3
12.2 15.3 11.0 13.4 17.6 22.0
115
88
62
49
108
81
56
43
99
73
49
37
89
64
42
30
5.1
6.1
8.1
10.1
5.8
7.1
9.3
11.6
7.2
8.7
11.4 14.3 10.7 12.9 17.0 21.3
106
81
59
46
99
76
54
42
91
68
47
36
81
59
39
29
4.2
5.2
6.9
8.7
4.9
6.0
8.0
10.0
6.8
8.2
10.8 13.6
9.6
12.6 16.6 20.7
106
83
62
50
99
77
56
45
86
66
46
36
75
56
38
28
4.2
5.2
6.9
8.7
4.8
5.9
7.9
9.9
6.6
7.9
10.5 13.0
7.4
9.8
15.0 20.3
99
79
59
48
94
73
54
44
83
64
46
36
71
53
37
28
3.8
4.6
6.1
7.6
4.8
5.9
7.8
9.8
5.9
7.6
10.1 12.7
5.9
7.8
11.9 16.6
101
82
62
51
90
71
53
43
80
62
45
36
68
51
36
27
3.9
4.7
6.2
7.8
4.3
5.3
6.9
8.7
4.7
6.2
9.6
12.3
4.7
6.2
9.6
13.5
96
78
60
49
91
73
55
45
77
61
45
36
65
50
35
27
Limit States Design (LSD)-Factored Resistance Diaphragm Shear, q, (N/mm) and Flexibility Factor, F, (mm x 10-6/N)
for 38 mm deep steel nestable deck fastened w/Hilti X-EDNK22/EDN19 w/screwed sidelaps (Canada only)1,2,3
No. of Transverse Nails per 900 mm Wide Deck Units=4 (every other flute)
Span (mm)
1200
1500
1800
2100
2400
2700
3000
Sidelap Connection
Deck Gauge Thickness
Strength, SLSD
Flexibility Factor, F
Strength, SLSD
Flexibility Factor, F
Strength, SLSD
Flexibility Factor, F
Strength, SLSD
Flexibility Factor, F
Strength, SLSD
Flexibility Factor, F
Strength, SLSD
Flexibility Factor, F
Strength, SLSD
Flexibility Factor, F
#10 Screw at 600 mm O.C. #10 Screw at 450 mm O.C. #10 Screw at 300 mm O.C. #10 Screw at 150 mm O.C.
22
20
18
16
22
20
18
16
22
20
18
16
22
20
18
16
4.7
5.6
7.4
9.3
4.7
5.6
7.4
9.3
6.2
7.4
9.8
12.2
8.1
9.8
12.8 16.0
595
384
210
132
595
384
210
132
578
369
197
120
567
359
188
113
3.9
4.7
6.1
7.6
4.6
5.5
7.3
9.2
5.9
7.1
9.3
11.6
7.9
9.5
12.6 15.7
500
328
186
122
487
317
176
113
474
305
166
103
462
294
156
95
4.0
4.7
6.2
7.8
4.6
5.5
7.2
9.2
5.6
6.8
8.9
11.2
7.8
9.4
12.3 15.5
425
281
161
106
415
272
154
100
405
262
145
92
392
251
135
83
3.4
4.1
5.4
6.8
4.0
4.8
6.3
7.9
5.4
6.6
8.6
10.8
7.6
9.3
12.2 15.3
383
257
152
103
372
247
143
96
355
232
130
84
342
220
120
75
3.5
4.2
5.6
7.1
4.0
4.8
6.3
8.0
5.3
6.3
8.5
10.6
7.6
9.2
12.1 15.2
340
230
137
94
332
222
130
88
318
209
119
78
304
197
108
68
3.1
3.8
4.9
6.2
4.0
4.9
6.5
8.1
5.2
6.2
8.2
10.3
7.5
9.2
12.0 15.0
318
218
133
93
301
203
120
82
289
192
110
73
275
179
99
63
3.2
3.9
5.2
6.6
3.6
4.5
5.9
7.4
5.1
6.2
8.1
10.2
7.5
9.0
12.0 14.9
290
365
123
86
283
193
117
81
266
177
103
69
252
165
92
59
Limit States Design (LSD)-Factored Resistance Diaphragm Shear, q, (N/mm) and Flexibility Factor, F, (mm x 10-6/N)
for 38 mm deep steel deck fastened w/Hilti X-EDNK22/EDN19 (Canada only)1,2,3
No. of Transverse Nails per 900 mm Wide Deck Units=7 (every flute)
Span (mm)
1200
1500
1800
2100
2400
2700
3000
Sidelap Connection
Deck Gauge Thickness
Strength, SLSD
Flexibility Factor, F
Strength, SLSD
Flexibility Factor, F
Strength, SLSD
Flexibility Factor, F
Strength, SLSD
Flexibility Factor, F
Strength, SLSD
Flexibility Factor, F
Strength, SLSD
Flexibility Factor, F
Strength, SLSD
Flexibility Factor, F
Button Punch 600 mm O.C. Button Punch 450 mm O.C. Button Punch 300 mm O.C. Button Punch 150 mm O.C.
22
20
18
16
22
20
18
16
22
20
18
16
22
20
18
16
5.8
7.1
9.5
12.1
5.8
7.1
9.5
12.1
6.5
8.1
11.2 14.8
7.8
10.0 14.3 19.6
129
96
67
51
129
96
67
51
126
94
65
50
122
90
62
47
4.6
5.6
7.5
9.8
4.8
6.0
8.3
10.9
5.5
6.9
9.9
13.2
6.9
8.9
13.2 18.2
126
97
71
56
125
96
69
55
122
94
67
53
116
88
63
49
4.0
4.9
6.9
9.2
4.2
5.4
7.5
10.1
4.8
6.1
8.8
12.1
6.2
8.2
12.2 17.3
126
100
75
61
124
98
73
59
121
95
71
57
114
89
65
52
3.4
4.2
5.9
7.8
3.6
4.6
6.5
8.7
4.2
5.5
8.1
11.3
5.8
7.8
11.6 16.6
130
105
81
66
128
103
79
65
122
98
75
61
113
90
67
55
3.2
4.0
5.6
7.5
3.3
4.2
6.1
8.3
3.9
5.1
7.5
10.7
5.4
7.3
11.2 16.0
133
109
85
71
130
107
83
69
125
102
79
66
113
91
70
57
2.7
3.5
4.9
6.6
3.1
4.0
5.8
8.0
3.6
4.7
7.2
10.1
5.2
6.9
10.8 15.6
139
115
92
77
134
111
88
74
128
106
83
70
114
93
72
60
2.6
3.3
4.8
6.6
2.7
3.5
5.2
7.2
3.4
4.5
6.8
9.8
4.9
6.7
10.5 15.3
143
120
96
81
140
118
94
80
131
110
87
73
115
95
75
62
1 The ratio of span of deck unit to average length of sheet is taken to be 1/3.
2 Diaphragm loads are based on steel decks having an average ultimate tensile strength of 55 ksi.
3 Values shown calculated in accordance with SDI equations using a factor of 0.5 for LSD for all load conditions.
124 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Limit States Design-Factored Resistance Diaphragm Tables for Deck Fasteners (Canada)
Limit States Design (LSD)-Factored Resistance Diaphragm Shear, q, (N/mm) and Flexibility Factor,
F, (mm x 10-6/N) for 38 mm deep steel deck fastened w/Hilti X-EDNK22/EDN19 (Canada only)1,2,3
Diaphragm Table 36-4 w/X-EDNK22/EDN19 Metric
No. of Transverse Nails per 900 mm Wide Deck Units=4 (every other flute)
Span (mm)
1200
1500
1800
2100
2400
2700
3000
Sidelap Connection
Deck Gauge Thickness
Strength, SLSD
Flexibility Factor, F
Strength, SLSD
Flexibility Factor, F
Strength, SLSD
Flexibility Factor, F
Strength, SLSD
Flexibility Factor, F
Strength, SLSD
Flexibility Factor, F
Strength, SLSD
Flexibility Factor, F
Strength, SLSD
Flexibility Factor, F
Button Punch 600 mm O.C. Button Punch 450 mm O.C. Button Punch 300 mm O.C. Button Punch 150 mm O.C.
22
20
18
16
22
20
18
16
22
20
18
16
22
20
18
16
4.1
4.3
5.7
7.4
3.5
4.3
5.7
7.4
4.0
5.0
7.0
9.3
4.8
6.2
8.9
12.0
612
399
224
144
612
399
224
144
607
395
220
141
599
388
214
135
3.3
4.0
5.5
7.2
3.5
4.5
6.2
8.1
4.1
5.2
7.4
10.0
5.3
6.8
9.9
13.6
521
348
203
137
518
345
201
134
513
340
196
130
502
330
188
123
2.9
3.6
5.2
6.9
3.2
4.1
5.9
7.9
3.6
4.7
6.9
9.4
4.9
6.5
9.5
13.2
462
315
190
132
459
311
188
130
452
306
183
125
438
293
172
116
2.5
3.2
4.5
6.0
2.7
3.8
4.9
6.8
3.3
4.5
6.5
8.9
4.7
6.1
9.2
12.9
426
297
186
134
422
293
183
131
412
283
175
124
394
268
161
111
2.4
2.9
4.3
6.0
2.5
3.5
4.8
6.7
3.1
4.1
6.2
8.6
4.5
5.9
8.9
12.7
398
282
182
134
394
278
179
131
383
268
170
123
362
249
154
109
2.0
2.6
3.8
5.3
2.4
3.4
4.7
6.6
2.9
3.9
6.0
8.3
4.2
5.8
8.8
12.5
382
276
184
139
373
268
177
132
361
257
168
124
337
236
149
107
2.0
2.6
3.8
5.3
2.1
3.2
4.2
6.0
2.7
3.6
5.8
8.1
4.1
5.6
8.7
12.3
367
393
183
140
362
265
180
137
346
250
166
125
318
225
145
106
Limit States Design (LSD)-Factored Resistance Diaphragm Shear, q, (N/mm) and Flexibility Factor, F, (mm x 10-6/N)
for 75 mm deep steel deck fastened with Hilti X-EDNK22/EDN19 (Canada only)1, 2, 3
No. of Transverse Nails per 600 mm Wide Deck Units=5 (every flute)
Span (mm)
2400
2700
1800
3300
3600
3900
4200
Sidelap Connection
Deck Gauge Thickness
Strength, SLSD
Flexibility Factor, F
Strength, SLSD
Flexibility Factor, F
Strength, SLSD
Flexibility Factor, F
Strength, SLSD
Flexibility Factor, F
Strength, SLSD
Flexibility Factor, F
Strength, SLSD
Flexibility Factor, F
Strength, SLSD
Flexibility Factor, F
Button Punch 600 mm O.C. Button Punch 450 mm O.C. Button Punch 300 mm O.C. Button Punch 150 mm O.C.
22
20
18
16
22
20
18
16
22
20
18
16
22
20
18
16
2.0
2.6
3.7
5.2
2.1
2.8
4.2
5.8
2.6
3.5
5.4
7.8
3.9
5.4
8.8
12.9
281
227
173
143
275
222
169
139
262
209
158
130
235
185
137
111
1.7
2.2
3.3
4.5
2.0
2.6
4.0
5.7
2.4
3.3
5.1
7.5
3.7
5.2
8.5
12.6
290
238
185
154
279
227
176
146
264
214
165
136
233
186
140
115
1.6
2.1
3.2
4.5
1.7
2.3
3.5
5.1
2.3
3.1
4.9
7.2
3.6
5.0
8.2
12.4
295
244
192
161
289
238
187
157
268
220
171
143
233
188
143
118
1.4
1.9
2.9
4.1
1.7
2.2
3.5
5.0
2.1
2.9
4.7
7.0
3.4
4.8
8.0
12.2
307
257
205
173
293
245
194
164
272
225
177
149
233
189
146
121
1.4
1.9
2.9
4.1
1.6
2.2
3.4
5.0
2.0
2.8
4.5
6.8
3.3
4.7
7.9
12
312
263
211
180
299
251
201
170
277
231
183
155
233
191
149
124
1.2
1.7
2.6
3.8
1.4
2.0
3.1
4.6
1.9
2.7
4.4
6.6
3.2
4.6
7.8
11.9
325
276
224
191
311
263
212
181
282
237
189
160
234
193
152
127
1.2
1.6
2.6
3.8
1.4
1.9
3.1
4.6
1.9
2.6
4.3
6.5
3.2
4.5
7.6
11.8
331
282
230
197
316
269
218
186
287
242
195
166
235
195
154
129
1 The ratio of span of deck unit to average length of sheet is taken to be 1/3.
2 Diaphragm loads are based on steel decks having an average ultimate tensile strength of 55 ksi.
3 Values shown calculated in accordance with SDI equations using a factor of 0.5 for LSD for all load conditions.
Note: Reference pages 122-123 for generally higher diaphragm capacities with Hilti Sidelap Connectors (SLC).
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 125
Notes
Qty
1 pcs
Accessories
Description
Notes
Qty
1 pcs
Notes
Qty
2,000 pcs
32,000 pcs
2,000 pcs
32,000 pcs
Notes
Qty
1 pcs
Accessories
Description
Notes
Qty
Magazine X-SM
Piston X-AP PSM
Buffer (reinforced) X-460-B
1 pcs
1 pcs
1 pcs
Qty
1,000 pcs
32,000 pcs
1,000 pcs
32,000 pcs
126 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
X-ENP-19 L15
Fastener
Material
Carbon Steel
Fastener
Plating
5 m Zinc1
Nominal Fastener
Hardness
58 HRC
X-ENP-19 L15
1
2
3
4
Material Specifications
3.5.3.3
Technical Data
3.5.3.4
Ordering Information
Approvals/Listings
3.5.3.2
X-ENP-19 L15
1 ASTM B633, SC 1, Type III. Reference Section 2.3.3.1 for more information.
Fastener
Product Description
3.5.3.1
5/8 4
965 (4.29)
Allowable Pullover and Shear Bearing Loads for Attaching Steel Deck 2,3,4
Fastener
X-ENP-19 L15 1
1
2
3
4
16 (0.0598)
Tension Shear
lb (kN)
lb (kN)
940
1050
(4.14)
(4.62)
18 (0.0474)
Tension Shear
lb (kN)
lb (kN)
875
840
(3.85)
(3.70)
24 (0.0239)
Tension Shear
lb (kN)
lb (kN)
400
440
(1.78)
(1.94)
26 (0.0179)
Tension Shear
lb (kN)
lb (kN)
185
335
(0.81)
(1.47)
Minimum base steel thickness must be greater than or equal to 1/4" (6 mm).
Allowable values are based on a safety factor of 3.0.
For alternate pullover capacities and factors of safety for uplift, refer to SDI Diaphragm Design Manual.
Loads based on ASTM A1008, or minimum ASTM A653 SQ33 steel deck.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 127
6''
1-1/2''
36''
152 mm
36''
1-1/2''
914 mm
38 mm
36/7
1-1/2''
36''
6'' 152 mm
36''
914/9
1-1/2''
914 mm
38 mm
Allowable Stress Design (ASD) Allowable Diaphragm Shears, SASD, (plf) and Stiffness Factors, G', (kips/in.) for Standard
1-1/2" Deep Flutes, 6" Center-to-Center Steel Deck (Fy 33 ksi; Fu 45 ksi) Installed with Hilti X-ENP-19 L15 Fasteners
with 36/9 or 36/7 End and Interior Support Fastener Patterns1,2,3,4
Gauge
Sidelap
Spacing
Hilti SLC5,6,7
36" O.C.
24" O.C.
18" O.C.
22
12" O.C.
6" O.C.
3" O.C.
36" O.C.
24" O.C.
18" O.C.
20
12" O.C.
6" O.C.
3" O.C.
36" O.C.
24" O.C.
18" O.C.
18
12" O.C.
6" O.C.
3" O.C.
36" O.C.
24" O.C.
18" O.C.
16
12" O.C.
6" O.C.
3" O.C.
Factor
36/11
4'-0"
9
SASD
804
G'
55.7
6''
SASD 36''861
G'
56.2
SASD
915
G'
56.8
SASD
1016
G'
57.5
SASD
1263
G'
59.2
SASD
1568
G'
61.0
SASD
1038
G'
78.5
SASD
1117
G'
79.5
SASD
1193
G'
80.0
SASD
1333
G'
81.8
SASD
1666
G'
84.8
SASD
2050
G'
88.5
SASD
1254
G'
123.5
SASD
1352
G'
126.6
SASD
1446
G'
128.2
SASD
1617
G'
131.6
SASD
2023
G'
138.9
SASD
2484
G'
147.1
SASD
1277
G'
172.4
SASD
1382
G'
175.4
SASD
1481
G'
178.6
SASD
1662
G'
185.2
SASD
2082
G'
196.1
SASD
2542
G'
212.8
7
561
52.8
623
53.7
683
54.3
793
55.7
1058
58.1
1362
60.2
731
73.3
819
74.9
902
76.3
1055
78.5
1409
83.0
1784
87.0
886
113.6
994
116.3
1097
119.0
1285
123.5
1715
133.3
2163
144.9
908
153.8
1023
158.7
1132
163.9
1330
172.4
1773
188.7
2214
208.3
5'-0"
9
7
688
485
61.5
57.5
750 1-1/2''
550
62.5
59.0
808
613
63.3
60.2
919
730
64.6
62.3
1192
1014
67.1
66.1
1532
1341
69.9
69.4
892
636
84.6
77.7
979
728
86.2
80.2
1061
815
87.7
82.6
1214
978
89.9
85.9
1583
1358
94.7
92.5
2012
1763
100.0
99.0
1079
771
128.4 115.0
1186
885
131.6 120.6
1288
993
135.1 123.5
1476
1193
139.3 131.0
1926
1655
149.5 144.7
2440
2138
161.3 158.7
1102
793
172.4 151.5
1216
914
178.6 158.7
1324
1029
181.8 166.7
1523
1239
192.3 175.4
1989
1716
208.3 200.0
2501
2192
227.3 222.2
9'-0"
914/11
10'-0"
9
7
9
436
329
408
71.4
64.1
71.9
1-1/2''
512 714
404mm
483
74.1
68.5
75.2
587
478
558
76.9
71.9
78.1
723
607
697
80.6
77.5
83.3
938
926
760
88.5
87.0
91.7
938
938
760
95.2
94.3
100.0
578
441
541
1-1/2''
90.9
81.3
90.9
686
549
649
96.2
87.0
96.2
793
649
757
100.0
92.6
101.0
975
828
942
106.4 100.0 107.5
1222
1222
990
117.6 114.9 122.0
1222
1222
990
129.9 128.2 135.1
710
542
661
125.5 109.1 123.5
844
676
795
133.0 118.9 131.6
973
795
928
138.9 126.6 138.9
1191
1015
1152
150.6 141.0 151.5
1725
1537
1420
172.4 167.2 175.4
1753
1753
1420
196.1 192.3 200.0
739
567
690
157.8 135.0 153.5
883
706
833
168.4 148.5 165.2
1011
832
969
178.6 161.3 175.4
1242
1064
1204
193.9 179.8 193.0
1797
1604
1771
226.8 218.8 228.9
2191
2150
1775
263.2 256.4 263.2
7
311
64.5
386 38 mm
69.4
461
73.5
591
79.4
760
90.1
760
99.0
418
80.6
526
87.7
627
93.5
808
102.0
990
119.0
990
133.3
512
106.4
646
117.6
769
126.6
991
140.8
1420
169.5
1420
196.1
537
131.1
679
145.7
806
158.7
1041
179.4
1589
221.1
1775
263.2
1 Tabulated diaphragm shear values are for attachment of steel deck to a base steel thickness greater than or equal to 1/4".
2 Tabulated ASD diaphragm shear loads are calculated with a safety factor () of 2.35 for wind loads. To calculate ASD values for load combinations involving earthquake, multiply values in
table by 2.35 and divide by a safety factor () of 2.50. Panel buckling has been checked.
3 At diaphragm perimeter, Hilti frame fasteners should be spaced at identical spacing as sidelap connectors.
4 Interpolation of diaphragm shear strengths and stiffness factors is allowed between span dimensions, sidelap spacings and deck gauge. Alternatively, use calculations as discussed in Section
3.5.1.8 to determine diaphragm shear strengths and stiffness factors directly.
5 To convert from sidelap spacing (SS) to sidelaps per span (SPS), use the following formula: SPS=((span, ft) x 12)/(SS, in.). Round up to the next whole sidelap connector.
6 For 16 gauge steel deck or for high tensile strength (fu > 65 ksi) 18 gauge steel deck, use S-SLC 02 M HWH. More information on Hilti Sidelap Connectors (SLC) can be found in Section 3.5.4.
7 For diaphragm shear load values using Hilti #10 HWH screws, use the Hilti Profis DF Diaphragm software or contact Hilti at 877-749-6337 or deck@hilti.com.
128 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
1-1/2''
36''
152 mm
36''
1-1/2''
914 mm
38 mm
36/5
6''
1-1/2''
36''
6'' 152 mm
36''
914/5
1-1/2''
914 mm
38 mm
Allowable Stress Design (ASD) Allowable Diaphragm Shears, SASD, (plf) and Stiffness Factors, G', (kips/in.) for Standard
1-1/2" Deep Flutes, 6" Center-to-Center Steel Deck (Fy 33 ksi; Fu 45 ksi) Installed with Hilti X-ENP-19 L15 Fasteners
with 36/5 or 36/4 End and Interior Support Fastener Patterns1,2,3,4
Gauge
Sidelap
Spacing
Hilti SLC5,6,7
36" O.C.
24" O.C.
18" O.C.
22
12" O.C.
6" O.C.
3" O.C.
36" O.C.
24" O.C.
18" O.C.
20
12" O.C.
6" O.C.
3" O.C.
36" O.C.
24" O.C.
18" O.C.
18
12" O.C.
6" O.C.
3" O.C.
36" O.C.
24" O.C.
18" O.C.
16
12" O.C.
6" O.C.
3" O.C.
Factor
36/7
4'-0"
5
SASD
504
G'
13.6
6''
SASD 36'' 557
G'
13.6
SASD
605
G'
13.7
SASD
688
G'
13.8
SASD
862
G'36/9 14.0
SASD
862
G'
14.1
6''
SASD
656
36''
G'
21.1
SASD
729
G'
21.2
SASD
795
G'
21.4
SASD
908
G'
21.6
SASD
36/11 1130
G'
22.0
S
1130
6''ASD
G' 36'' 22.3
SASD
795
G'
38.8
SASD
884
G'
39.2
SASD
965
G'
39.7
SASD
1103
G'
40.3
SASD
1370
G'
41.5
SASD
1370
G'
42.4
SASD
813
G'
62.1
SASD
908
G'
63.3
SASD
993
G'
64.1
SASD
1136
G'
65.8
SASD
1404
G'
68.5
SASD
1404
G'
70.9
4
410
9.9
458
9.9
501
10.0
572
10.0
700
10.1
700
10.2
536
15.4
602
15.5
660
15.6
753
15.8
913
16.0
913
16.2
650
28.8
731
29.2
801
29.5
914
30.0
1105
30.8
1105
31.3
666
46.9
751
47.8
825
48.8
940
49.8
1128
51.8
1128
53.2
5'-0"
5
4
442
365
16.3
11.9
4991-1/2''
418
16.4
12.0
552
465
16.6
12.1
644
544
16.8
12.2
837
688
17.1
12.4
837
688
17.3
12.6
579
481
1-1/2''
24.9
18.4
659
554
25.3
18.7
731
618
25.5
18.9
856
721
25.9
19.1
1103
899
26.6
19.6
1103
899
27.11-1/2''
19.9
703
584
44.6
33.7
801
673
45.5
34.4
890
751
46.3
35.0
1042
877
47.4
35.8
1339
1089
49.3
37.1
1339
1089
51.0
38.2
722
601
69.4
53.5
825
695
71.4
55.2
919
776
73.0
56.5
1077
905
75.8
58.1
1376
1114
80.0
61.3
1376
1114
84.0
64.1
9'-0"
914/7
10'-0"
5
4
5
315
272
298
24.8
18.7
26.3
1-1/2''
mm
385 914337
370
25.5
19.3
27.3
446
393
431
26.0
19.6
28.0
555
487
542
26.8
20.2
29.0
787
662
760
28.0
30.4
914/920.9
787
662
760
28.8
21.4
31.4
423
370
402
1-1/2''
914
mm
35.8
27.7
37.7
518
455
499
37.3
28.7
39.5
602
531
585
38.5
29.5
41.0
750
656
736
40.0
30.6
42.9
914/11872
1048
990
42.4
32.2
45.9
1048
872
990
44.1 714
33.2
47.8
1-1/2''
mm
521
452
493
58.5
46.4
60.2
633
556
610
61.7
49.1
64.5
736
649
715
64.5
51.0
67.6
917
801
900
68.5
54.0
71.9
1276
1059
1267
74.6
58.3
79.4
1276
1059 1-1/2''
1267
79.4
61.3
85.5
540
470
516
83.3
67.7
84.0
659
580
637
89.3
72.9
91.7
768
677
748
94.3
76.9
97.1
957
833
940
102.0
82.8
106.4
1318
1087
1310
114.9
92.1
120.5
1318
1087
1310
125.0
99.0
133.3
4
260
20.1
326 38 mm
20.8
383
21.3
479
21.9
658
22.8
658
23.5
354
38 mm
29.4
442
30.8
519
31.7
647
33.0
868
35.0
868
36.2 38 mm
434
48.3
540
51.5
635
54.1
790
57.5
1054
62.9
1054
66.7
452
69.5
565
75.6
663
80.0
823
87.2
1083
98.2
1083
106.4
1 Tabulated diaphragm shear values are for attachment of steel deck to a base steel thickness greater than or equal to 1/4".
2 Tabulated ASD diaphragm shear loads are calculated with a safety factor () of 2.35 for wind loads. To calculate ASD values for load combinations involving earthquake, multiply values in
table by 2.35 and divide by a safety factor () of 2.50. Panel buckling has been checked.
3 At diaphragm perimeter, Hilti frame fasteners should be spaced at identical spacing as sidelap connectors.
4 Interpolation of diaphragm shear strengths and stiffness factors is allowed between span dimensions, sidelap spacings and deck gauge. Alternatively, use calculations as discussed in Section
3.5.1.8 to determine diaphragm shear strengths and stiffness factors directly.
5 To convert from sidelap spacing (SS) to sidelaps per span (SPS), use the following formula: SPS=((span, ft) x 12)/(SS, in.). Round up to the next whole sidelap connector.
6 For 16 gauge steel deck or for high tensile strength (fu > 65 ksi) 18 gauge steel deck, use S-SLC 02 M HWH. More information on Hilti Sidelap Connectors (SLC) can be found in Section 3.5.4.
7 For diaphragm shear load values using Hilti #10 HWH screws, use the Hilti Profis DF Diaphragm software or contact Hilti at 877-749-6337 or deck@hilti.com.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 129
6''
152 mm
36''
1-1/2''
36''
1-1/2''
914 mm
38 mm
36/9
6''
6'' 152 mm
36''
1-1/2''
36''
914/9
1-1/2''
914 mm
Load Resistance Factor Design (LRFD) Factored Resistance Diaphragm Shears, SLRFD, (plf) and Stiffness Factors, G',
(kips/in.) for Standard 1-1/2" Deep Flutes, 6" Center-to-Center Steel Deck (Fy 33 ksi; Fu 45 ksi) Installed with Hilti
X-ENP-19 L15 Fasteners with 36/9 or 36/7 End and Interior Support Fastener Patterns1,2,3,4
Gauge
Sidelap
Spacing
Hilti SLC5,6,7
36" O.C.
24" O.C.
18" O.C.
22
12" O.C.
6" O.C.
3" O.C.
36" O.C.
24" O.C.
18" O.C.
20
12" O.C.
6" O.C.
3" O.C.
36" O.C.
24" O.C.
18" O.C.
18
12" O.C.
6" O.C.
3" O.C.
36" O.C.
24" O.C.
18" O.C.
16
12" O.C.
6" O.C.
3" O.C.
Factor
36/11
4'-0"
9
SLRFD
1322
6''
G'
55.7
SLRFD 36''1415
G'
56.2
SLRFD
1504
G'
56.8
SLRFD
1669
G'
57.5
SLRFD
2076
G'
59.2
SLRFD
2577
G'
61.0
SLRFD
1705
G'
78.5
SLRFD
1836
G'
79.5
SLRFD
1961
G'
80.0
SLRFD
2190
G'
81.8
SLRFD
2737
G'
84.8
SLRFD
3369
G'
88.5
SLRFD
2060
G'
123.5
SLRFD
2222
G'
126.6
SLRFD
2375
G'
128.2
SLRFD
2658
G'
131.6
SLRFD
3325
G'
138.9
SLRFD
4082
G'
147.1
SLRFD
2098
G'
172.4
SLRFD
2270
G'
175.4
SLRFD
2433
G'
178.6
SLRFD
2731
G'
185.2
SLRFD
3422
G'
196.1
SLRFD
4177
G'
212.8
7
922
52.8
1024
53.7
1122
54.3
1303
55.7
1739
58.1
2238
60.2
1202
73.3
1346
74.9
1483
76.3
1734
78.5
2315
83.0
2932
87.0
1456
113.6
1634
116.3
1803
119.0
2111
123.5
2818
133.3
3554
144.9
1492
153.8
1681
158.7
1860
163.9
2185
172.4
2913
188.7
3638
208.3
5'-0"
9
7
1131
796
61.5
57.5
12321-1/2''
904
62.5
59.0
1328
1006
63.3
60.2
1509
1199
64.6
62.3
1959
1666
67.1
66.1
2517
2204
69.9
69.4
1466
1044
84.6
77.7
1608
1196
86.2
80.2
1743
1340
87.7
82.6
1995
1607
89.9
85.9
2601
2231
94.7
92.5
3305
2897
100.0
99.0
1774
1267
128.4 115.0
1949
1454
131.6 120.6
2116
1632
135.1 123.5
2426
1960
139.3 131.0
3165
2719
149.5 144.7
4009
3514
161.3 158.7
1811
1302
172.4 151.5
1998
1502
178.6 158.7
2176
1691
181.8 166.7
2503
2037
192.3 175.4
3269
2820
208.3 200.0
4110
3603
227.3 222.2
9'-0"
914/11
38 mm
10'-0"
9
7
9
717
540
670
71.4
64.1
71.9
1-1/2''
714
mm
841
664
794
74.1
68.5
75.2
965
786
918
76.9
71.9
78.1
1188
997
1145
80.6
77.5
83.3
1501
1501
1216
88.5
87.0
91.7
1501
1501
1216
95.2
94.3
100.0
949
7251-1/2''
889
90.9
81.3
90.9
1126
902
1066
96.2
87.0
96.2
1303
1067
1243
100.0
92.6
101.0
1602
1360
1548
106.4 100.0 107.5
1956
1956
1584
117.6 114.9 122.0
1956
1956
1584
129.9 128.2 135.1
1167
891
1086
125.5 109.1 123.5
1387
1111
1306
133.0 118.9 131.6
1599
1306
1525
138.9 126.6 138.9
1957
1667
1893
150.6 141.0 151.5
2805
2525
2272
172.4 167.2 175.4
2805
2805
2272
196.1 192.3 200.0
1215
932
1133
157.8 135.0 153.5
1451
1161
1369
168.4 148.5 165.2
1662
1367
1593
178.6 161.3 175.4
2041
1749
1978
193.9 179.8 193.0
2954
2635
2840
226.8 218.8 228.9
3506
3506
2840
263.2 256.4 263.2
7
511
64.5
635 38 mm
69.4
757
73.5
970
79.4
1216
90.1
1216
99.0
688
80.6
865
87.7
1031
93.5
1328
102.0
1584
119.0
1584
133.3
842
106.4
1061
117.6
1263
126.6
1628
140.8
2272
169.5
2272
196.1
883
131.1
1116
145.7
1324
158.7
1711
179.4
2611
221.1
2840
263.2
1 Tabulated diaphragm shear values are for attachment of steel deck to a base steel thickness greater than or equal to 1/4".
2 Tabulated LRFD diaphragm shear loads are calculated with a phi factor () of 0.70 for wind loads. To calculate LRFD values for load combinations involving earthquake, divide values in table
by 0.70 and multiply by a phi factor () of 0.65. Panel buckling has been checked.
3 At diaphragm perimeter, Hilti frame fasteners should be spaced at identical spacing as sidelap connectors.
4 Interpolation of diaphragm shear strengths and stiffness factors is allowed between span dimensions, sidelap spacings and deck gauge. Alternatively, use calculations as discussed in Section
3.5.1.8 to determine diaphragm shear strengths and stiffness factors directly.
5 To convert from sidelap spacing (SS) to sidelaps per span (SPS), use the following formula: SPS=((span, ft) x 12)/(SS, in.). Round up to the next whole sidelap connector.
6 For 16 gauge steel deck or for high tensile strength (fu > 65 ksi) 18 gauge steel deck, use S-SLC 02 M HWH. More information on Hilti Sidelap Connectors (SLC) can be found in Section 3.5.4.
7 For diaphragm shear load values using Hilti #10 HWH screws, use the Hilti Profis DF Diaphragm software or contact Hilti at 877-749-6337 or deck@hilti.com.
130 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
1-1/2''
36''
152 mm
36''
1-1/2''
914 mm
38 mm
36/5
6''
1-1/2''
36''
6'' 152 mm
36''
914/5
1-1/2''
914 mm
38 mm
Load Resistance Factor Design (LRFD) Factored Resistance Diaphragm Shears, SLRFD, (plf) and Stiffness Factors, G',
(kips/in.) for Standard 1-1/2" Deep Flutes, 6" Center-to-Center Steel Deck (Fy 33 ksi; Fu 45 ksi) Installed with Hilti
X-ENP-19 L15 Fasteners with 36/5 or 36/4 End and Interior Support Fastener Patterns1,2,3,4
Gauge
Sidelap
Spacing
Hilti SLC5,6,7
36" O.C.
24" O.C.
18" O.C.
22
12" O.C.
6" O.C.
3" O.C.
36" O.C.
24" O.C.
18" O.C.
20
12" O.C.
6" O.C.
3" O.C.
36" O.C.
24" O.C.
18" O.C.
18
12" O.C.
6" O.C.
3" O.C.
36" O.C.
24" O.C.
18" O.C.
16
12" O.C.
6" O.C.
3" O.C.
Factor
36/7
4'-0"
5
SLRFD
829
6''
G'
13.6
SLRFD 36'' 915
G'
13.6
SLRFD
993
G'
13.7
SLRFD
1131
G'
13.8
SLRFD
1416
G'36/9 14.0
SLRFD
1416
G'
14.1
6''
SLRFD
36'' 1079
G'
21.1
SLRFD
1198
G'
21.2
SLRFD
1306
G'
21.4
SLRFD
1492
G'
21.6
36/11 1856
SLRFD
G'
22.0
S
1856
6''
LRFD
G' 36'' 22.3
SLRFD
1306
G'
38.8
SLRFD
1453
G'
39.2
SLRFD
1586
G'
39.7
SLRFD
1812
G'
40.3
SLRFD
2251
G'
41.5
SLRFD
2251
G'
42.4
SLRFD
1337
G'
62.1
SLRFD
1492
G'
63.3
SLRFD
1632
G'
64.1
SLRFD
1866
G'
65.8
SLRFD
2307
G'
68.5
SLRFD
2307
G'
70.9
4
674
9.9
753
9.9
823
10.0
939
10.0
1151
10.1
1151
10.2
881
15.4
989
15.5
1084
15.6
1237
15.8
1500
16.0
1500
16.2
1067
28.8
1201
29.2
1317
29.5
1502
30.0
1815
30.8
1815
31.3
1095
46.9
1235
47.8
1355
48.8
1545
49.8
1853
51.8
1853
53.2
5'-0"
5
4
727
600
16.3
11.9
1-1/2''
820
687
16.4
12.0
907
765
16.6
12.1
1059
894
16.8
12.2
1376
1130
17.1
12.4
1376
1130
17.3
12.6
9521-1/2''
790
24.9
18.4
1083
910
25.3
18.7
1202
1015
25.5
18.9
1407
1186
25.9
19.1
1813
1478
26.6
19.6
1813
1478
27.11-1/2''
19.9
1155
959
44.6
33.7
1316
1106
45.5
34.4
1462
1235
46.3
35.0
1712
1442
47.4
35.8
2200
1790
49.3
37.1
2200
1790
51.0
38.2
1186
987
69.4
53.5
1356
1142
71.4
55.2
1510
1276
73.0
56.5
1770
1487
75.8
58.1
2261
1831
80.0
61.3
2261
1831
84.0
64.1
9'-0"
914/7
10'-0"
5
4
5
517
448
490
24.8
18.7
26.3
1-1/2''
914554
mm
633
607
25.5
19.3
27.3
732
645
709
26.0
19.6
28.0
911
800
891
26.8
20.2
29.0
1293
1087
1216
28.0
30.4
914/920.9
1293
1087
1216
28.8
21.4
31.4
696
661
1-1/2''
914608
mm
35.8
27.7
37.7
851
748
820
37.3
28.7
39.5
990
872
961
38.5
29.5
41.0
1233
1078
1209
40.0
30.6
42.9
914/11
1723
1433
1584
42.4
32.2
45.9
1723
1433
1584
1-1/2''
44.1 714
33.2
47.8
mm
856
742
810
58.5
46.4
60.2
1040
914
1002
61.7
49.1
64.5
1210
1067
1175
64.5
51.0
67.6
1507
1316
1479
68.5
54.0
71.9
2096
1739
2082
74.6
58.3
79.4
2096
1739 1-1/2''
2082
79.4
61.3
85.5
888
772
848
83.3
67.7
84.0
1083
953
1046
89.3
72.9
91.7
1263
1113
1229
94.3
76.9
97.1
1572
1369
1545
102.0
82.8
106.4
2165
1786
2152
114.9
92.1
120.5
2165
1786
2152
125.0
99.0
133.3
4
428
20.1
38 mm
536
20.8
629
21.3
787
21.9
1081
22.8
1081
23.5
582
38 mm
29.4
726
30.8
853
31.7
1063
33.0
1427
35.0
1427
36.2 38 mm
713
48.3
888
51.5
1043
54.1
1299
57.5
1732
62.9
1732
66.7
743
69.5
928
75.6
1090
80.0
1352
87.2
1779
98.2
1779
106.4
1 Tabulated diaphragm shear values are for attachment of steel deck to a base steel thickness greater than or equal to 1/4".
2 Tabulated LRFD diaphragm shear loads are calculated with a phi factor () of 0.70 for wind loads. To calculate LRFD values for load combinations involving earthquake, divide values in table
by 0.70 and multiply by a phi factor () of 0.65. Panel buckling has been checked.
3 At diaphragm perimeter, Hilti frame fasteners should be spaced at identical spacing as sidelap connectors.
4 Interpolation of diaphragm shear strengths and stiffness factors is allowed between span dimensions, sidelap spacings and deck gauge. Alternatively, use calculations as discussed in Section
3.5.1.8 to determine diaphragm shear strengths and stiffness factors directly.
5 To convert from sidelap spacing (SS) to sidelaps per span (SPS), use the following formula: SPS=((span, ft) x 12)/(SS, in.). Round up to the next whole sidelap connector.
6 For 16 gauge steel deck or for high tensile strength (fu > 65 ksi) 18 gauge steel deck, use S-SLC 02 M HWH. More information on Hilti Sidelap Connectors (SLC) can be found in Section 3.5.4.
7 For diaphragm shear load values using Hilti #10 HWH screws, use the Hilti Profis DF Diaphragm software or contact Hilti at 877-749-6337 or deck@hilti.com.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 131
6'' 152 mm
36''
1-1/2''
914 mm
38 mm
152 mm
914 mm
38 mm
914/9
(36/9)
914/9
914/7
(36/7)
914/7
1-1/2''
914 mm
38 mm
152 mm
914 mm
38 mm
Limit States Design (LSD)- Factored Resistance Diaphragm Shears, SLSD, (N/mm) and Stiffness Factors, G', (103 N/mm)
for Standard 38 mm Deep Flutes, 152 mm Center-to-Center Steel Deck (Fy 230 MPa; Fu 310 MPa) Installed with Hilti
X-ENP-19 L15 Fasteners with 914/9 (36/9) or 914/7 (36/7) End and Interior Support Fastener Patterns1,2,3,4
Gauge
Sidelap
Spacing
36/9
Hilti
SLC5,6,7
900 mm
6''
152 o.c.
mm
36''
600 mm o.c.
450 mm o.c.
22
300 mm o.c.
150 mm o.c.
36/11
75 mm o.c.
6''
36''o.c.
900 mm
600 mm o.c.
450 mm o.c.
20
300 mm o.c.
150 mm o.c.
75 mm o.c.
900 mm o.c.
600 mm o.c.
450 mm o.c.
18
300 mm o.c.
150 mm o.c.
75 mm o.c.
900 mm o.c.
600 mm o.c.
450 mm o.c.
16
300 mm o.c.
150 mm o.c.
75 mm o.c.
Factor
914/11
1200
9
7
SLSD
18.2
12.7
G'
9.7
9.2
1-1/2''
714 mm
SLSD
19.4
14.1
G'
9.8
9.3
SLSD
20.6
15.4
G'
9.8
9.4
SLSD
22.9
17.9
G'
10.0
9.7
SLSD
28.4
23.8
G'
10.3
10.1
SLSD
35.0
30.4
G'
10.5
10.5
SLSD
23.4
1-1/2''16.5
G'
13.7
12.8
SLSD
25.2
18.5
G'
13.8
13.1
SLSD
26.9
20.4
G'
13.9
13.3
SLSD
30.0
23.8
G'
14.2
13.7
SLSD
37.4
31.7
G'
14.7
14.4
SLSD
45.7
39.8
G'
15.4
15.2
SLSD
28.3
20.0
G'
21.7
19.6
SLSD
30.5
22.4
G'
22.2
20.4
SLSD
32.6
24.7
G'
22.2
20.8
SLSD
36.4
28.9
G'
22.7
21.7
SLSD
45.5
38.5
G'
23.8
23.3
SLSD
55.4
48.2
G'
25.6
25.0
SLSD
28.8
20.5
G'
30.3
27.0
SLSD
31.2
23.1
G'
30.3
27.8
SLSD
33.4
25.6
G'
31.3
28.6
SLSD
37.5
30.0
G'
32.3
30.3
SLSD
46.8
39.9
G'
34.5
33.3
SLSD
56.7
49.4
G'
37.0
35.7
1500
9
15.5
10.7
38
16.9
10.9
18.2
11.0
20.7
11.2
26.8
11.7
34.2
12.2
20.1
14.8
22.1
15.0
23.9
15.2
27.4
15.7
35.6
16.5
44.9
17.2
24.4
22.5
26.8
23.0
29.1
23.3
33.3
24.4
43.3
26.1
54.4
27.8
24.9
30.3
27.5
31.3
29.9
32.3
34.4
33.3
44.8
37.0
55.8
40.0
7
11.0
10.0
mm
12.4
10.3
13.8
10.5
16.5
10.8
22.8
11.5
29.9
12.0
14.4
13.6
16.4
14.0
18.4
14.3
22.0
15.0
30.5
16.1
39.3
17.2
17.4
20.2
20.0
21.0
22.4
21.7
26.9
22.9
37.2
25.3
47.7
27.8
17.9
26.3
20.7
27.8
23.3
29.4
28.0
31.3
38.6
34.5
48.9
38.5
Span (mm)
1800
2100
2400
Fasteners Per Sheet To Support
914/9
9
7
9
7
9
7
13.5
9.6
11.9
8.7
10.7
8.0
152 mm
11.4
10.6
11.9
10.9
12.2
11.1
15.1
11.3
13.6
10.4
12.4914 mm
9.7
11.7
10.9
12.3
11.4
12.7
11.8
16.5
12.7
15.2
11.9
14.1
11.3
11.9
11.2
12.5
11.8
13.0
12.2
19.1
15.5
18.0
14.7
17.1
14.1
12.2
11.7
13.0
12.5
13.7
13.0
25.7
22.1
24.8
21.6
24.1
21.2
12.9
12.6
13.9
13.6
14.7
14.5
914/11
33.6
29.6
33.1
29.3
26.8
26.8
13.5
13.5
14.7
14.5
15.6
15.6
152 mm
17.7
12.8
15.7
11.6
14.2714 mm
10.7
15.4
14.0
15.8
14.2
15.9
14.3
19.9
15.0
18.2
13.9
16.7
13.1
15.8
14.6
16.3
15.0
16.6
15.2
21.8
17.0
20.2
16.0
19.0
15.3
16.1
15.2
16.7
15.6
17.2
15.9
25.5
20.8
24.0
19.9
22.9
19.2
16.7
15.9
17.5
16.6
18.1
17.2
34.2
29.7
33.2
29.1
32.4
28.6
17.9
17.4
19.0
18.5
19.9
19.4
44.2
39.0
43.7
38.9
35.0
35.0
18.9
18.9
20.4
20.0
21.7
21.3
21.6
15.6
19.3
14.2
17.5
13.1
22.7
20.2
22.7
19.9
22.4
19.6
24.1
18.3
22.1
17.0
20.5
16.1
23.5
21.3
23.6
21.2
23.6
21.1
26.5
20.8
24.6
19.6
23.1
18.7
24.4
22.2
24.4
22.2
24.4
22.2
31.0
25.4
29.3
24.4
27.9
23.6
25.3
23.7
25.8
24.2
26.2
24.6
41.7
36.3
40.5
35.5
39.6
35.0
27.6
26.7
28.7
27.8
29.5
28.6
53.7
47.3
53.1
47.0
50.1
46.8
30.3
29.4
31.3
31.3
33.3
32.3
22.1
16.1
20.0
14.8
18.1
13.7
29.9
26.0
29.3
25.3
28.6
24.5
24.8
19.0
22.8
17.7
21.3
16.7
30.2
26.7
31.1
27.6
30.7
27.2
27.4
21.6
25.5
20.4
24.0
19.5
32.3
29.4
32.3
28.6
31.3
28.6
32.1
26.5
30.4
25.5
29.1
24.7
33.9
31.4
34.1
31.6
34.2
31.7
43.2
37.7
42.1
37.0
41.2
36.5
37.7
36.2
38.6
37.2
39.3
37.9
55.2
48.6
54.7
48.3
54.3
48.1
41.7
41.7
43.5
43.5
45.5
43.5
2700
9
9.9
12.5
11.6
13.0
13.3
13.3
16.3
14.1
21.2
15.4
21.2
16.7
13.1
15.9
15.5
16.7
18.0
17.5
22.0
18.5
27.6
20.8
27.6
22.7
16.1
22.1
19.1
23.4
22.0
24.4
26.9
26.4
38.8
30.2
39.6
34.5
16.7
27.8
20.0
29.7
22.9
31.3
28.1
34.1
40.5
39.8
49.5
45.5
3000
7
9
7.4
9.2
11.2
12.7
9.138 mm
10.9
12.0
13.2
10.8
12.6
12.7
13.7
13.7
15.7
13.5
14.5
20.8
17.2
15.2
16.1
21.2
17.2
16.4
17.5
10.038 mm
12.2
14.3
15.9
12.4
14.7
15.4
16.9
14.7
17.1
16.1
17.5
18.7
21.3
17.5
18.9
27.6
22.4
20.0
21.3
27.6
22.4
22.2
23.3
12.3
15.0
19.2
21.7
15.3
18.0
20.8
23.3
18.0
21.0
22.2
24.4
22.9
26.0
25.0
26.3
34.6
32.1
29.4
30.3
39.6
32.1
33.3
34.5
12.8
15.6
23.8
27.1
16.0
18.9
26.2
29.1
18.8
21.9
28.6
31.3
24.0
27.2
31.6
34.0
36.1
39.9
38.4
40.2
47.9
40.1
45.5
47.6
7
7.0
11.4
8.7
12.2
10.4
12.8
13.3
13.9
17.2
15.6
17.2
17.2
9.5
14.1
11.9
15.4
14.2
16.4
18.2
17.9
22.4
20.8
22.4
23.3
11.6
18.9
14.6
20.8
17.4
22.2
22.4
25.0
32.1
30.3
32.1
34.5
12.2
23.2
15.4
25.7
18.2
27.8
23.5
31.6
35.8
38.8
40.1
45.5
1 Tabulated diaphragm shear values are for attachment of steel deck to a base steel thickness greater than or equal to 6 mm.
2 Tabulated LSD diaphragm shear loads are calculated with a phi factor () of 0.65 for wind loads. To calculate LSD values for load combinations involving earthquake, divide values in table
by 0.65 and multiply by a phi factor () of 0.60. Panel buckling has been checked.
3 At diaphragm perimeter, Hilti frame fasteners should be spaced at identical spacing as sidelap connectors.
4 Interpolation of diaphragm shear strengths and stiffness factors is allowed between span dimensions, sidelap spacings and deck gauge. Alternatively, use calculations as discussed in Section
3.5.1.8 to determine diaphragm shear strengths and stiffness factors directly.
5 To convert from sidelap spacing (SS) to sidelaps per span (SPS), use the following formula: SPS=(span, mm)/(SS, mm). Round up to the next whole sidelap connector.
6 For 16 gauge steel deck or for high tensile strength (fu > 65 ksi) 18 gauge steel deck, use S-SLC 02 M HWH. More information on Hilti Sidelap Connectors (SLC) can be found in Section 3.5.4.
7 For diaphragm shear load values using Hilti #10 HWH screws, use the Hilti Profis DF Diaphragm software or contact Hilti at 877-749-6337 or deck@hilti.com.
132 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
6''152 mm
36''
914 mm1-1/2''
38 mm
152 mm
914 mm
38 mm
Steel Deck Fastening Systems
c
36/4
6''152 mm
36''
914/5
(36/5)
914/5
914/4
(36/4)
914/4
914 mm1-1/2''
38 mm
152 mm
914 mm
38 mm
Limit States Design (LSD)- Factored Resistance Diaphragm Shears, SLSD, (N/mm) and Stiffness Factors, G', (103 N/mm)
for Standard 38 mm Deep Flutes, 152 mm Center-to-Center Steel Deck (Fy 230 MPa; Fu 310 MPa) Installed with Hilti
X-ENP-19 L15 Fasteners with 914/5 (36/5) or 914/4 (36/4) End and Interior Support Fastener Patterns1,2,3,4
Gauge
Sidelap
Spacing
Hilti 36/5
SLC5,6,7
900 mm o.c.
6''152 mm
36''
600 mm o.c.
450 mm o.c.
22
300 mm o.c.
150 mm o.c.
36/7
75 mm o.c.
6''152 mm
900 mm36''
o.c.
600 mm o.c.
450 mm o.c.
20
300 mm o.c.
36/9
150 mm o.c.
75
6''mm
152o.c.
mm
36''
900 mm o.c.
600 mm o.c.
450 mm o.c.
18
300 36/11
mm o.c.
150 mm o.c.
6''
75 mm36''
o.c.
900 mm o.c.
600 mm o.c.
450 mm o.c.
16
300 mm o.c.
150 mm o.c.
75 mm o.c.
Factor
1200
914/7 5
4
SLSD
11.4
9.2
G'
2.3
1.7
SLSD 914 12.5
mm1-1/2''
10.3
G'
2.4
1.7
SLSD
13.6
11.3
G'
2.4
1.7
SLSD
15.5
12.8
G'
2.4
1.7
SLSD
19.2
15.6
G'
1.7
914/9 2.4
SLSD
19.2
15.6
G'
2.4
1.8
SLSD
14.8
12.1
G' 914 mm
3.61-1/2''
2.7
SLSD
16.4
13.6
G'
3.7
2.7
SLSD
17.9
14.8
G'
3.7
2.7
SLSD
20.4
16.9
G'
3.7
2.7
S914/11
25.2
20.3
LSD
G'
3.8
2.8
SLSD
25.2
20.3
G'
3.8
2.8
1-1/2''
714 mm
SLSD
17.9
14.6
G'
6.7
5.0
SLSD
19.9
16.5
G'
6.8
5.1
SLSD
21.7
18.0
G'
6.8
5.1
SLSD
24.8
20.5
G'
7.0
5.2
SLSD
30.6
24.6
G'
7.2
5.3
SLSD
30.61-1/2''
24.6
G'
7.4
5.4
SLSD
18.4
15.0
G'
10.8
8.1
SLSD
20.5
16.9
G'
11.0
8.3
SLSD
22.4
18.6
G'
11.1
8.4
SLSD
25.5
21.1
G'
11.4
8.6
SLSD
31.3
25.2
G'
11.9
8.9
SLSD
31.3
25.2
G'
12.3
9.3
1500
5
4
10.0
8.2
2.8
2.1
11.3
9.4
38 mm
2.8
2.1
12.4
10.5
2.9
2.1
14.5
12.2
2.9
2.1
18.7
15.3
2.9
2.1
18.7
15.3
3.0
2.2
13.1
10.8
4.338 mm
3.2
14.9
12.5
4.4
3.2
16.5
13.9
4.4
3.3
19.3
16.2
4.5
3.3
24.6
20.0
4.6
3.4
24.6
20.0
4.7
3.4
38 mm
15.9
13.2
7.8
5.8
18.1
15.2
7.9
6.0
20.0
16.9
8.0
6.1
23.4
19.7
8.2
6.2
29.9
24.3
8.5
6.4
29.9
24.3
8.8
6.6
16.3
13.6
12.0
9.3
18.6
15.7
12.5
9.6
20.7
17.5
12.7
9.8
24.2
20.3
13.2
10.1
30.7
24.9
13.9
10.6
30.7
24.9
14.5
11.1
Span (mm)
1800
2100
2400
Fasteners Per Sheet To Support
5
4
5
4
5914/5 4
9.0
7.5
8.3
7.0
7.6
6.5
3.2
2.4
3.6152 mm
2.7
4.0
3.0
10.3
8.8
9.7
8.3
9.1 9147.9
mm
3.3
2.4
3.7
2.8
4.1
3.1
11.6
9.9
11.0
9.5
10.5
9.1
3.3
2.5
3.8
2.8
4.1
3.1
13.8
11.8
13.3
11.4
12.8
11.2
3.4
2.5
3.8
2.8
4.3
3.2
18.3
15.1
18.0
15.0
17.7
14.8
3.5
2.5
3.9
2.9
4.4
3.3
914/7
18.3
15.1
18.0
15.0
17.7
14.8
3.5
2.6
4.0
3.0
4.5
3.3
152 mm
11.8
10.0
10.9
9.3
10.2
8.8
mm
4.9
3.7
5.4
4.1
5.8 9144.5
13.7
11.7
12.9
11.1
12.2
10.6
5.0
3.7
5.6
4.2
6.1
4.6
15.4
13.2
14.7
12.7
14.1
12.3
5.1
3.8
5.6
4.3
6.2
4.7
18.4
15.7
17.8
15.3
17.3
15.0
5.2
3.9
5.8
4.4
6.4
4.8
24.2
19.8
23.8
19.7
23.6
914/919.5
5.3
4.0
6.1
4.5
6.7
5.1
24.2
19.8
23.8
19.7
23.6
19.5
5.5
4.0
6.3152 mm
4.6
6.9
5.2
914 mm
14.4
12.1
13.3
11.3
12.4
10.7
8.5
6.6
9.3
7.2
9.8
7.7
16.7
14.2
15.7
13.5
14.9
13.0
8.8
6.7
9.6
7.4
10.2
8.0
18.8
16.1
17.9
15.5
17.2
15.0
9.0
6.9
9.9
7.6
10.6
8.3
22.5
19.1
21.7
18.7
21.1
18.3
914/118.7
9.3
7.1
10.3
7.9
11.1
29.4
24.0
29.0
23.9
28.7
23.7
9.8
7.4
11.0
8.4
12.0
9.3
152 mm
29.4
24.0
29.0
23.9
28.7 714
23.7
mm
10.2
7.7
11.5
8.7
12.7
9.7
14.8
12.5
13.7
11.7
12.9
11.1
13.0
10.2
13.7
10.9
14.3
11.4
17.3
14.8
16.3
14.1
15.5
13.5
12.1
13.5
10.6
14.5
11.5
15.2
19.5
16.7
18.6
16.1
17.9
15.6
13.9
11.0
14.9
11.9
15.9
12.7
23.3
19.8
22.6
19.4
22.0
19.0
14.5
11.4
15.9
12.5
16.9
13.5
30.2
24.6
29.9
24.5
29.6
24.3
15.6
12.2
17.2
13.6
18.5
14.8
30.2
24.6
29.9
24.5
29.6
24.3
16.7
12.8
18.5
14.3
20.0
15.9
2700
5
7.1
4.3
8.7
4.4
10.1
4.5
12.5
4.7
17.5
4.9
17.5
5.0
9.6
6.3
11.7
6.5
13.6
6.7
16.9
6.9
23.4
7.4
23.4
7.6
11.8
10.2
14.3
10.8
16.6
11.2
20.7
11.9
28.4
13.0
28.4
13.7
12.2
14.5
14.9
15.6
17.3
16.4
21.6
17.9
29.4
20.0
29.4
21.7
3000
4
5
6.2
6.7
3.2
4.6
7.6 38 mm
8.3
3.3
4.7
8.9
9.7
3.4
4.9
11.0
12.2
3.5
5.0
14.7
17.2
3.6
5.3
14.7
17.2
3.7
5.4
8.4
9.1
4.8 38 mm
6.6
10.3
11.3
5.0
6.9
12.0
13.2
5.1
7.1
14.8
16.6
5.3
7.5
19.4
22.4
5.6
7.9
19.4
22.4
5.7
8.3
38 mm
10.2
11.2
8.1
10.5
12.5
13.8
8.5
11.2
14.6
16.1
8.9
11.8
18.0
20.3
9.4
12.5
23.6
28.2
10.1
13.9
23.6 38 28.2
mm
10.6
14.7
10.6
11.7
11.8
14.7
13.1
14.4
12.7
16.1
15.3
16.9
13.3
16.9
18.7
21.2
14.4
18.5
24.2
29.2
16.0
21.3
24.2
29.2
17.2
23.3
4
5.9
3.5
7.4
3.6
8.6
3.7
10.8
3.8
14.7
4.0
14.7
4.0
8.0
5.1
10.0
5.3
11.7
5.5
14.6
5.7
19.4
6.1
19.4
6.3
9.8
8.5
12.2
9.0
14.3
9.4
17.8
10.0
23.5
10.9
23.5
11.5
10.2
12.2
12.7
13.2
15.0
14.1
18.5
15.2
24.1
17.1
24.1
18.5
1 Tabulated diaphragm shear values are for attachment of steel deck to a base steel thickness greater than or equal to 6 mm.
2 Tabulated LSD diaphragm shear loads are calculated with a phi factor () of 0.65 for wind loads. To calculate LSD values for load combinations involving earthquake, divide values in table
by 0.65 and multiply by a phi factor () of 0.60. Panel buckling has been checked.
3 At diaphragm perimeter, Hilti frame fasteners should be spaced at identical spacing as sidelap connectors.
5 Interpolation of diaphragm shear strengths and stiffness factors is allowed between span dimensions, sidelap spacings and deck gauge. Alternatively, use calculations as discussed in Section
3.5.1.8 to determine diaphragm shear strengths and stiffness factors directly.
5 To convert from sidelap spacing (SS) to sidelaps per span (SPS), use the following formula: SPS=(span, mm)/(SS, mm). Round up to the next whole sidelap connector.
6 For 16 gauge steel deck or for high tensile strength (fu > 65 ksi) 18 gauge steel deck, use S-SLC 02 M HWH. More information on Hilti Sidelap Connectors (SLC) can be found in Section 3.5.4.
7 For diaphragm shear load values using Hilti #10 HWH screws, use the Hilti Profis DF Diaphragm software or contact Hilti at 877-749-6337 or deck@hilti.com.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 133
Limit States Design-Factored Resistance Diaphragm Tables for Deck Fasteners (Canada)
Diaphragm Table 36-7
Limit States Design (LSD)-Factored Resistance Diaphragm Shear, q, (N/mm) and Flexibility Factor, F, (mm x 10-6/N)
w/X-ENP-19 L15 Metric
for 38 mm deep steel nestable deck fastened with Hilti X-ENP-19 L15 with screwed sidelaps (Canada only)1, 2, 3
No. of Transverse Nails per 900 mm Wide Deck Units=7 (every flute)
Sidelap Connection
#12 Screw at 600 mm O.C. #12 Screw at 450 mm O.C. #12 Screw at 300 mm O.C. #12 Screw at 150 mm O.C.
Span (mm)
Deck Gauge Thickness
22
20
18
16
22
20
18
16
22
20
18
16
22
20
18
16
Strength, SLSD
7.1
8.5
11.2 13.9
7.1
8.5
11.2 13.9
9.2
11.0 14.6 18.2 12.8 15.4 20.3 25.4
1200
Flexibility Factor, F
109
78
51
38
109
78
51
38
104
74
47
34
99
69
43
30
Strength, SLSD
5.6
8.5
8.9
11.3
6.7
8.0
10.6 13.2
8.5
10.2 13.4 16.8 12.2 14.7 19.4 24.3
1500
Flexibility Factor, F
102
75
52
39
98
72
49
37
93
68
45
33
87
62
40
29
Strength, SLSD
5.5
6.7
8.8
11.0
6.3
7.8
10.2 12.7
7.9
9.5
12.6 15.7 11.8 14.2 18.8 23.5
1800
Flexibility Factor, F
94
71
50
38
91
68
47
36
86
64
44
33
79
57
38
28
Strength, SLSD
4.7
5.6
7.5
9.4
5.4
6.6
8.7
10.9
7.5
9.2
12.0 15.0 11.5 13.9 18.3 22.9
2100
Flexibility Factor, F
93
72
52
41
89
68
49
38
82
61
43
33
74
54
37
27
Strength, SLSD
4.7
5.8
7.6
9.5
5.4
6.5
8.6
10.8
7.3
8.7
11.5 14.5 11.3 13.6 18.0 22.6
2400
Flexibility Factor, F
89
69
50
40
85
66
48
38
78
60
42
33
70
52
35
27
Strength, SLSD
4.2
5.1
6.7
8.5
5.3
6.5
8.6
10.8
7.1
8.5
11.2 14.0 11.0 13.4 17.6 22.2
2700
Flexibility Factor, F
89
70
52
42
82
64
47
37
76
58
42
33
66
50
35
26
Strength, SLSD
4.2
5.2
6.8
8.6
4.8
5.8
7.6
9.6
6.8
8.2
10.9 13.6 10.9 13.3 17.4 21.9
3000
Flexibility Factor, F
86
68
51
42
82
65
49
39
73
57
41
33
64
48
34
26
Note: Reference pages 132-133 for generally higher diaphragm capacities with Hilti Sidelap Connectors (SLC).
134 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Limit States Design-Factored Resistance Diaphragm Tables for Deck Fasteners (Canada)
Diaphragm Table 36-4
Limit States Design (LSD)-Factored Resistance Diaphragm Shear, q, (N/mm) and Flexibility Factor, F, (mm x 10-6/N)
w/X-ENP-19 L15 Metric
for 38 mm deep steel deck fastened with Hilti X-ENP-19 L15 (Canada only)1,2,3
No. of Transverse Nails per 900 mm Wide Deck Units=4 (every other flute)
Sidelap Connection
Button Punch 600 mm O.C. Button Punch 450 mm O.C. Button Punch 300 mm O.C. Button Punch 150 mm O.C.
Span (mm)
Deck Gauge Thickness
22
20
18
16
22
20
18
16
22
20
18
16
22
20
18
16
Strength, SLSD
4.3
5.4
7.2
9.3
4.3
5.4
7.2
9.3
4.9
6.2
8.7
11.5
6.0
7.6
11.0 14.8
1200
Flexibility Factor, F
589
378
205
128
589
378
205
128
587
377
204
127
584
374
201
124
Strength, SLSD
3.5
4.3
5.9
7.6
3.8
4.8
6.6
8.6
4.3
5.5
7.8
10.5
5.5
7.1
10.3 14.2
1500
Flexibility Factor, F
492
322
180
116
491
321
179
115
489
318
177
114
484
314
174
111
Strength, SLSD
3.2
3.9
5.5
7.4
3.4
4.2
6.1
8.2
3.9
5.1
7.2
9.9
5.2
6.7
10.0 13.7
1800
Flexibility Factor, F
430
285
165
110
428
284
164
109
426
282
162
107
419
276
157
102
Strength, SLSD
2.6
3.3
4.7
6.2
2.8
3.6
5.3
7.2
3.4
4.6
6.8
9.4
4.8
6.3
9.6
13.4
2100
Flexibility Factor, F
388
262
156
107
387
261
155
106
382
257
152
103
374
250
145
97
Strength, SLSD
2.5
3.2
4.6
6.2
2.6
3.4
5.1
7.1
3.2
4.2
6.5
8.9
4.6
6.1
9.3
13.2
2400
Flexibility Factor, F
358
246
150
106
356
244
149
105
351
240
145
101
341
231
138
94
Strength, SLSD
2.2
2.8
4.0
5.5
2.5
3.3
4.8
6.9
3.1
4.0
6.1
8.7
4.5
6.0
9.2
12.9
2700
Flexibility Factor, F
337
235
148
107
333
232
145
104
328
227
141
101
316
216
132
92
Strength, SLSD
2.1
2.7
4.0
5.5
2.2
2.9
4.3
6.1
2.8
3.9
5.9
8.5
4.3
5.8
8.9
12.7
3000
Flexibility Factor, F
320
227
146
107
318
225
145
106
311
218
139
101
297
206
128
91
Note: Reference pages 132-133 for generally higher diaphragm capacities with Hilti Sidelap Connectors (SLC).
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 135
Notes
Qty
1 pcs
Accessories
Description
Notes
Qty
1 pcs
Notes
Qty
tf 1/4" (6 mm)
tf 1/4" (6 mm)
2,000 pcs
32,000 pcs
Notes
Qty
1 pcs
DX 76 Decking System
Tools
Description
DX 76 Hand Held Decking Tool
with MX76 Magazine
Accessories
Description
MX 76 Magazine
X-76-FN-15
X-76-P-ENP piston (incl. piston stopper)
X-76-PS piston stopper
Notes
Qty
1 pcs
1 pcs
1 pcs
1 pcs
Qty
tf 1/4" (6 mm)
tf 1/4" (6 mm)
1,000 pcs
32,000 pcs
Fasteners (Non-Combo)
Description
Qty
tf 1/4" (6 mm)
100 pcs
136 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Fastener
Material
Carbon Steel
Carbon Steel
Carbon Steel
S-SLC 01 M HWH
S-SLC 02 M HWH
Hilti #10 HWH Screw
Product Description
3.5.4.2
Material Specifications
3.5.4.3
Technical Data
3.5.4.4
Ordering Information
S-SLC 01 M HWH
Collated Sidelap Connectors
S-SLC 01 M HWH
Sidelap Connector
3.5.4.1
S-SLC 02 M HWH
Collated Sidelap Connectors
Fastener
Plating
5 m Zinc1
5 m Zinc2
5 m Zinc2
Allowable Tension (Pullout or Pullover) and Shear Bearing Loads for Hilti SLC
Sidelap Connectors1,2,3
Sheet Steel Gauge
Fastener
S-SLC 01 M HWH4,5
S-SLC 02 M HWH5
Hilti #10
HWH Screw6
22 to 22
20 to 20
18 to 18
16 to 16
240
120
290
150
385
(0.47)
(1.07)
(0.53)
(1.29)
(0.67)
(1.71)
85
240
100
290
130
385
165
485
(0.38)
(1.07)
(0.44)
(1.29)
(0.58)
(1.71)
(0.73)
(2.16)
70
210
85
255
115
340
145
430
(0.31)
(0.93)
(0.38)
(1.13)
(0.51)
(1.51)
(0.64)
(1.91)
1 Based upon attachment of two-same thickness layers of ASTM A1008 or minimum ASTM A653 SQ33
steel deck.
2 Allowable capacities based on a safety factor of 3.0.
3 Allowable tension capacities based upon the controlling capacity of pullout, pullover or fastener tension
strength.
4 Use of S-SLC 01 M HWH with 18 gauge steel deck is recommended only for standard tensile strength
(45 fu 65 ksi) steel deck. For high tensile strength (fu > 65 ksi) 18 gauge steel deck, use
S-SLC 02 M HWH.
5 Allowable shear capacities calculated according to Section 4.5 of SDI DDM03 for standard No. 12 screw.
For shear capacities when used in diaphragm applications in combination with Hilti deck frame fasteners,
reference Qs values in Table 8 in Section 3.5.1.8.
6 Allowable shear capacities calculated according to Section 4.5 of SDI DDM03 for standard No. 10 screw.
S-SLC 02 M HWH
Sidelap Connectors
Approvals/Listings
ICC-ES (International Code Council)
ESR-2776 (AC43 for S-SLC 01
and S-SLC 02)
ESR-2197 (AC43 for #10 HWH Screws)
ESR-2196 (AC118 for S-SLC 02
and #10 HWH Screws)
COLA (City of Los Angeles)
RR 25877, RR 25678, RR 25296
FM (Factory Mutual)
S-SLC 01 M HWH and S-SLC 02 M
HWH fasteners for securing Class 1
Steel Roof Deck sidelaps with 1-60 and
1-90 wind uplift ratings.
S-SLC 02 M HWH listed for higher
wind uplift ratings with FM Approved
Lightweight Insulating Concrete Roof
Deck Assemblies. Refer to FM RoofNav
for specific assembly listings.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 137
Notes
Qty
Accessories
Description
Notes
Qty
SDT 30 Magazine
SDT Integrated Driver and Setter
1 pcs
1 pcs
Qty
10,000 pcs
25,000 pcs
50,000 pcs
100,000
pcs
15,000
pcs
Qty
250
250
250
1 Use of S-SLC 01 M HWH with 18 gauge steel deck is recommended only for standard tensile strength (45 fu 65 ksi)
steel deck. For high tensile strength (fu > 65 ksi) 18 gauge steel deck, use S-SLC 02 M HWH.
138 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Span = 4'-0''
Recommended Hilti Powder-Actuated Frame Fastener Pattern-Sidelap Spacing Hilti SLC (in. o.c.)*
X-ENP-19 with tf 1/4"
22 ga.
20 ga.
18 ga.
16 ga.
22 ga.
20 ga.
18 ga.
22 ga.
20 ga.
18 ga.
36/3-48
36/3-48
36/3-42
36/3-30
36/3-24
36/3-18
36/3-14
36/4-20
36/4-18
36/4-14
36/4-12
36/5-16
36/5-14
36/5-10
36/5-8
36/5-7
36/9-24
36/9-18
36/9-12
36/9-10
36/9-8
36/9-7
36/9-5
36/11-7
36/11-5
36/11-4
36/11-3
36/3-48
36/3-48
36/3-48
36/3-48
36/3-48
36/3-48
36/3-42
36/3-30
36/3-20
36/3-18
36/4-24
36/4-20
36/4-18
36/4-14
36/4-12
36/5-16
36/5-14
36/5-10
36/5-8
36/5-7
36/5-6
36/9-16
36/9-12
36/9-10
36/9-8
36/9-7
36/11-7
36/11-4
36/11-3
36/3-48
36/3-48
36/3-48
36/3-48
36/3-48
36/3-48
36/3-48
36/3-48
36/3-48
36/3-36
36/3-24
36/3-20
36/3-16
36/4-24
36/4-20
36/4-18
36/4-14
36/5-20
36/5-16
36/5-14
36/5-10
36/5-8
36/5-7
36/9-20
36/9-16
36/9-12
36/9-8
36/9-5
36/11-5
36/11-3
36/3-48
36/3-48
36/3-48
36/3-48
36/3-48
36/3-48
36/3-48
36/3-48
36/3-48
36/3-42
36/3-30
36/3-24
36/3-18
36/3-14
36/4-24
36/4-18
36/4-16
36/4-12
36/5-18
36/5-14
36/5-12
36/5-10
36/5-8
36/9-24
36/9-18
36/9-14
36/9-8
36/9-6
36/11-6
36/11-4
36/3-48
36/3-30
36/3-24
36/3-18
36/4-30
36/4-24
36/4-18
36/4-14
36/4-12
36/5-18
36/5-14
36/5-12
36/9-48
36/5-8
36/9-24
36/9-18
36/9-14
36/9-10
36/9-8
36/9-7
36/9-6
36/11-7
36/11-6
36/11-5
36/11-4
36/11-3
36/4-48
36/4-48
36/4-48
36/4-48
36/4-48
36/4-48
36/4-48
36/4-42
36/4-30
36/4-24
36/4-20
36/4-16
36/4-14
36/5-20
36/5-16
36/5-12
36/9-48
36/9-42
36/9-24
36/9-20
36/9-16
36/9-12
36/9-10
36/9-8
36/9-6
36/11-8
36/4-48
36/4-48
36/4-48
36/4-48
36/4-48
36/4-48
36/4-48
36/4-48
36/4-48
36/4-48
36/4-42
36/4-30
36/4-24
36/4-20
36/4-18
36/5-24
36/5-20
36/9-48
36/7-20
36/9-48
36/9-48
36/9-30
36/9-20
36/11-30
36/11-20
36/11-16
36/4-48
36/4-48
36/4-36
36/4-24
36/4-20
36/4-18
36/4-14
36/4-12
36/5-16
36/5-14
36/9-48
36/9-48
36/9-30
36/9-20
36/9-16
36/9-12
36/9-10
36/9-8
36/9-7
36/11-8
36/11-7
36/11-6
36/4-48
36/4-48
36/4-48
36/4-48
36/4-48
36/4-48
36/4-48
36/4-36
36/4-24
36/4-20
36/4-18
36/4-14
36/4-12
36/5-18
36/5-14
36/5-12
36/9-42
36/9-30
36/9-20
36/9-16
36/9-12
36/9-10
36/9-8
36/9-7
36/9-6
36/11-7
36/4-48
36/4-48
36/4-48
36/4-48
36/4-48
36/4-48
36/4-48
36/4-48
36/4-42
36/4-36
36/4-24
36/4-20
36/4-18
36/4-14
36/4-12
36/5-18
36/5-14
36/5-12
36/7-16
36/9-24
36/9-20
36/7-10
36/9-12
36/9-10
36/9-8
36/9-7
36/11-7
* Please refer to footnotes listed at the end of this section on page 144.
Allowable
Diaphragm Design
Strength, plf*
SASD
SASD
(wind)
(seismic)
254
270
272
289
291
309
311
331
333
354
356
379
381
406
408
434
437
464
467
497
500
532
535
569
572
609
612
651
655
697
701
746
750
798
802
854
859
914
919
977
983
1046
1052
1119
1126
1197
1204
1281
1289
1371
1379
1467
1579
1679
1807
1923
2069
2201
2369
2520
Span = 4'-6''
Recommended Hilti Powder-Actuated Frame Fastener Pattern-Sidelap Spacing Hilti SLC (in. o.c.)*
X-ENP-19 with tf 1/4"
22 ga.
20 ga.
18 ga.
16 ga.
22 ga.
20 ga.
18 ga.
22 ga.
20 ga.
18 ga.
36/3-54
36/3-54
36/3-42
36/3-30
36/3-24
36/3-20
36/3-16
36/4-24
36/4-18
36/4-16
36/4-12
36/5-18
36/5-14
36/5-12
36/5-10
36/5-8
36/5-7
36/9-18
36/9-14
36/9-10
36/9-8
36/9-7
36/9-6
36/9-5
36/11-6
36/11-5
36/11-3
36/3-54
36/3-54
36/3-54
36/3-54
36/3-54
36/3-54
36/3-42
36/3-30
36/3-24
36/3-20
36/3-16
36/4-24
36/4-20
36/4-16
36/4-12
36/5-18
36/5-14
36/5-12
36/5-10
36/5-8
36/5-7
36/9-18
36/9-14
36/9-10
36/9-8
36/9-7
36/9-5
36/11-5
36/11-3
36/3-54
36/3-54
36/3-54
36/3-54
36/3-54
36/3-54
36/3-54
36/3-54
36/3-54
36/3-42
36/3-30
36/3-24
36/3-20
36/3-14
36/4-24
36/4-18
36/4-16
36/4-12
36/5-18
36/5-14
36/5-12
36/5-10
36/5-8
36/5-7
36/9-16
36/9-12
36/9-8
36/9-6
36/11-6
36/11-4
36/3-54
36/3-54
36/3-54
36/3-54
36/3-54
36/3-54
36/3-54
36/3-54
36/3-54
36/3-42
36/3-36
36/3-24
36/3-20
36/3-16
36/4-24
36/4-20
36/4-18
36/4-14
36/4-12
36/5-16
36/5-12
36/5-10
36/5-8
36/5-7
36/9-18
36/9-14
36/9-10
36/9-6
36/11-6
36/11-4
36/3-48
36/3-36
36/3-24
36/3-20
36/3-16
36/4-24
36/4-20
36/4-16
36/4-14
36/5-18
36/5-16
36/5-12
36/5-10
36/9-36
36/9-24
36/9-18
36/9-14
36/9-12
36/9-8
36/9-8
36/9-6
36/9-5
36/11-6
36/11-5
36/11-4
36/11-3
36/4-54
36/4-54
36/4-54
36/4-54
36/4-54
36/4-54
36/4-48
36/4-42
36/4-30
36/4-24
36/4-20
36/4-18
36/4-14
36/4-12
36/5-16
36/5-14
36/5-12
36/9-36
36/9-24
36/9-20
36/9-16
36/9-12
36/9-10
36/9-8
36/9-7
36/9-6
36/11-6
36/4-54
36/4-54
36/4-54
36/4-54
36/4-54
36/4-54
36/4-54
36/4-54
36/4-54
36/4-54
36/4-42
36/4-36
36/4-30
36/4-24
36/4-20
36/5-24
36/5-20
36/5-18
36/9-54
36/9-54
36/9-42
36/9-30
36/9-20
36/11-30
36/11-20
36/11-16
36/4-54
36/4-48
36/4-36
36/4-30
36/4-24
36/4-20
36/4-16
36/4-14
36/5-18
36/5-14
36/5-12
36/9-42
36/9-30
36/9-20
36/9-18
36/9-14
36/9-10
36/9-8
36/9-7
36/9-6
36/11-7
36/11-6
36/4-54
36/4-54
36/4-54
36/4-54
36/4-54
36/4-54
36/4-48
36/4-36
36/4-30
36/4-24
36/4-20
36/4-16
36/4-14
36/5-18
36/5-16
36/5-12
36/9-42
36/9-30
36/9-20
36/9-18
36/9-14
36/9-12
36/9-8
36/9-8
36/9-6
36/11-8
36/4-54
36/4-54
36/4-54
36/4-54
36/4-54
36/4-54
36/4-54
36/4-54
36/4-48
36/4-36
36/4-30
36/4-24
36/4-20
36/4-18
36/4-14
36/5-20
36/5-16
36/5-14
36/9-36
36/7-14
36/7-12
36/9-18
36/9-14
36/9-12
36/9-10
36/9-8
36/11-8
* Please refer to footnotes listed at the end of this section on page 144.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 139
Span = 5'-0''
Recommended Hilti Powder-Actuated Frame Fastener Pattern-Sidelap Spacing Hilti SLC (in. o.c.)*
X-ENP-19 with tf 1/4"
22 ga.
20 ga.
18 ga.
16 ga.
22 ga.
20 ga.
18 ga.
22 ga.
20 ga.
18 ga.
36/3-60
36/3-60
36/3-48
36/3-36
36/3-30
36/3-24
36/3-18
36/3-14
36/3-12
36/4-18
36/4-14
36/4-12
36/5-16
36/5-12
36/5-10
36/5-8
36/5-8
36/9-18
36/9-14
36/9-12
36/9-10
36/9-8
36/9-7
36/11-8
36/11-6
36/9-4
36/11-4
36/3-60
36/3-60
36/3-60
36/3-60
36/3-60
36/3-60
36/3-48
36/3-36
36/3-30
36/3-24
36/3-18
36/3-14
36/3-12
36/4-18
36/4-14
36/4-12
36/5-16
36/5-14
36/5-12
36/5-10
36/5-8
36/5-7
36/9-14
36/9-12
36/9-10
36/9-8
36/9-6
36/9-4
36/11-4
36/11-3
36/3-60
36/3-60
36/3-60
36/3-60
36/3-60
36/3-60
36/3-60
36/3-60
36/3-60
36/3-42
36/3-36
36/3-24
36/3-20
36/3-18
36/3-14
36/4-20
36/4-18
36/4-14
36/4-12
36/5-16
36/5-14
36/5-10
36/5-8
36/5-8
36/9-18
36/9-14
36/9-10
36/9-7
36/9-5
36/11-5
36/3-60
36/3-60
36/3-60
36/3-60
36/3-60
36/3-60
36/3-60
36/3-60
36/3-60
36/3-48
36/3-36
36/3-30
36/3-24
36/3-20
36/3-16
36/3-12
36/4-18
36/4-16
36/4-14
36/5-18
36/5-14
36/5-12
36/5-10
36/5-8
36/5-7
36/9-16
36/9-10
36/9-7
36/9-5
36/11-5
36/3-48
36/3-36
36/3-30
36/3-24
36/3-20
36/3-16
36/4-20
36/4-18
36/5-24
36/5-20
36/5-16
36/5-14
36/5-12
36/5-10
36/5-8
36/9-20
36/9-14
36/9-12
36/9-10
36/9-8
36/9-7
36/9-6
36/11-7
36/11-6
36/11-5
36/11-4
36/11-3
36/4-60
36/4-60
36/4-60
36/4-60
36/4-60
36/4-60
36/4-60
36/4-42
36/4-36
36/4-30
36/4-24
36/4-20
36/4-16
36/4-14
36/4-12
36/5-16
36/5-12
36/9-36
36/9-24
36/9-20
36/9-16
36/9-14
36/9-10
36/9-8
36/9-8
36/9-6
36/11-6
36/4-60
36/4-60
36/4-60
36/4-60
36/4-60
36/4-60
36/4-60
36/4-60
36/4-60
36/4-60
36/4-48
36/4-36
36/4-30
36/4-24
36/4-20
36/4-18
36/5-24
36/5-20
36/9-60
36/9-60
36/9-42
36/9-30
36/9-20
36/9-18
36/11-20
36/11-16
36/4-60
36/4-48
36/4-36
36/4-30
36/4-24
36/4-20
36/4-18
36/5-24
36/5-20
36/5-16
36/5-14
36/5-12
36/9-30
36/9-24
36/9-18
36/9-14
36/9-12
36/9-10
36/9-8
36/9-7
36/9-6
36/11-7
36/11-6
36/4-60
36/4-60
36/4-60
36/4-60
36/4-60
36/4-60
36/4-48
36/4-36
36/4-30
36/4-24
36/4-20
36/4-18
36/4-16
36/5-20
36/5-16
36/5-14
36/5-12
36/9-30
36/9-24
36/9-18
36/9-14
36/9-12
36/9-10
36/9-8
36/9-7
36/9-6
36/11-6
36/4-60
36/4-60
36/4-60
36/4-60
36/4-60
36/4-60
36/4-60
36/4-60
36/4-48
36/4-36
36/4-30
36/4-24
36/4-24
36/4-20
36/4-16
36/4-14
36/5-18
36/5-14
36/5-12
36/7-16
36/7-14
36/7-12
36/9-16
36/9-12
36/9-10
36/9-8
36/9-6
36/11-6
* Please refer to footnotes listed at the end of this section on page 144.
Allowable
Diaphragm Design
Strength, plf*
SASD
SASD
(wind)
(seismic)
222
236
237
253
254
270
272
289
291
309
311
331
333
354
356
379
381
406
408
434
437
464
467
497
500
532
535
569
572
609
612
651
655
697
701
746
750
798
802
854
859
914
919
977
983
1046
1052
1119
1126
1197
1204
1281
1379
1467
1579
1679
1807
1923
2069
2201
Span = 5'-6''
Recommended Hilti Powder-Actuated Frame Fastener Pattern-Sidelap Spacing Hilti SLC (in. o.c.)*
X-ENP-19 with tf 1/4"
22 ga.
20 ga.
18 ga.
16 ga.
22 ga.
20 ga.
18 ga.
22 ga.
20 ga.
18 ga.
36/3-66
36/3-66
36/3-48
36/3-42
36/3-30
36/3-24
36/3-20
36/3-18
36/3-14
36/4-18
36/4-16
36/4-14
36/4-12
36/4-10
36/5-12
36/5-10
36/5-8
36/5-7
36/9-14
36/9-12
36/9-10
36/9-8
36/9-7
36/9-6
36/9-5
36/11-6
36/11-4
36/11-3Z
36/3-66
36/3-66
36/3-66
36/3-66
36/3-66
36/3-60
36/3-48
36/3-42
36/3-30
36/3-24
36/3-20
36/3-18
36/4-24
36/4-20
36/4-16
36/4-14
36/4-12
36/4-10
36/5-12
36/5-10
36/5-8
36/5-8
36/9-16
36/9-12
36/9-10
36/9-8
36/9-6
36/11-6
36/11-4
36/11-3
36/3-66
36/3-66
36/3-66
36/3-66
36/3-66
36/3-66
36/3-66
36/3-66
36/3-60
36/3-48
36/3-36
36/3-30
36/3-24
36/3-20
36/3-16
36/3-14
36/4-20
36/4-16
36/4-14
36/4-12
36/4-10
36/5-12
36/5-10
36/5-8
36/5-8
36/9-14
36/9-10
36/9-7
36/9-5
36/9-4
36/3-66
36/3-66
36/3-66
36/3-66
36/3-66
36/3-66
36/3-66
36/3-66
36/3-66
36/3-48
36/3-42
36/3-36
36/3-24
36/3-20
36/3-18
36/4-24
36/4-20
36/4-18
36/4-14
36/4-12
36/5-16
36/5-14
36/5-12
36/5-10
36/5-8
36/5-7
36/9-12
36/9-8
36/9-6
36/11-6
36/3-48
36/3-42
36/3-30
36/3-24
36/3-20
36/3-18
36/4-24
36/4-20
36/4-16
36/4-14
36/5-18
36/5-14
36/5-12
36/5-10
36/9-24
36/5-8
36/9-16
36/9-12
36/9-10
36/9-8
36/9-8
36/9-6
36/11-7
36/11-6
36/9-4
36/11-4
36/11-3
36/4-66
36/4-66
36/4-66
36/4-66
36/4-66
36/4-66
36/4-60
36/4-48
36/4-36
36/4-30
36/4-24
36/4-20
36/4-18
36/4-16
36/5-20
36/5-16
36/5-14
36/5-12
36/9-24
36/9-20
36/9-18
36/9-14
36/9-12
36/9-10
36/9-8
36/9-7
36/11-7
36/4-66
36/4-66
36/4-66
36/4-66
36/4-66
36/4-66
36/4-66
36/4-66
36/4-66
36/4-60
36/4-48
36/4-42
36/4-30
36/4-24
36/4-24
36/4-20
36/5-24
36/5-20
36/5-18
36/9-60
36/9-42
36/9-30
36/9-24
36/9-18
36/11-20
36/11-18
36/11-12
36/4-60
36/4-48
36/4-42
36/4-30
36/4-24
36/4-24
36/4-20
36/4-16
36/4-14
36/5-18
36/5-16
36/5-12
36/9-30
36/9-24
36/9-20
36/9-16
36/9-12
36/9-10
36/9-8
36/9-8
36/9-6
36/11-7
36/11-6
36/4-66
36/4-66
36/4-66
36/4-66
36/4-66
36/4-60
36/4-48
36/4-42
36/4-36
36/4-30
36/4-24
36/4-20
36/4-18
36/4-14
36/5-18
36/5-16
36/5-14
36/5-12
36/9-24
36/9-20
36/9-16
36/9-14
36/7-8
36/9-10
36/9-8
36/9-7
36/11-6
36/4-66
36/4-66
36/4-66
36/4-66
36/4-66
36/4-66
36/4-66
36/4-60
36/4-48
36/4-42
36/4-36
36/4-30
36/4-24
36/4-20
36/4-18
36/4-16
36/5-20
36/5-16
36/5-14
36/5-12
36/9-24
36/9-20
36/9-16
36/9-14
36/9-12
36/9-10
36/9-7
36/11-7
* Please refer to footnotes listed at the end of this section on page 144.
140 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Span = 6'-0''
Recommended Hilti Powder-Actuated Frame Fastener Pattern-Sidelap Spacing Hilti SLC (in. o.c.)*
X-ENP-19 with tf 1/4"
22 ga.
20 ga.
18 ga.
16 ga.
22 ga.
20 ga.
18 ga.
22 ga.
20 ga.
18 ga.
36/3-72
36/3-72
36/3-48
36/3-42
36/3-36
36/3-30
36/3-24
36/3-20
36/3-16
36/4-20
36/4-18
36/4-14
36/4-12
36/5-16
36/5-14
36/5-12
36/5-10
36/5-8
36/5-7
36/9-14
36/9-10
36/9-8
36/9-8
36/9-7
36/9-6
36/9-5
36/11-5
36/11-3
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-48
36/3-42
36/3-36
36/3-30
36/3-24
36/3-20
36/3-16
36/3-14
36/4-18
36/4-16
36/4-14
36/4-12
36/4-10
36/5-12
36/5-10
36/5-8
36/5-7
36/9-14
36/9-12
36/9-10
36/9-7
36/11-7
36/11-5
36/11-3
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-48
36/3-42
36/3-36
36/3-30
36/3-24
36/3-20
36/3-16
36/4-20
36/4-18
36/4-16
36/4-12
36/5-16
36/5-14
36/5-12
36/5-10
36/5-8
36/5-7
36/9-12
36/9-8
36/9-6
36/11-6
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-60
36/3-48
36/3-36
36/3-30
36/3-24
36/3-20
36/3-18
36/4-24
36/4-20
36/4-16
36/4-14
36/4-12
36/4-10
36/5-12
36/5-10
36/5-8
36/5-8
36/9-12
36/9-8
36/9-7
36/9-5
36/3-60
36/3-48
36/3-36
36/3-30
36/3-24
36/3-20
36/3-16
36/3-14
36/4-18
36/4-16
36/4-14
36/4-12
36/5-14
36/5-12
36/5-10
36/9-20
36/9-16
36/9-14
36/9-12
36/9-10
36/9-8
36/9-7
36/9-6
36/11-7
36/11-6
36/11-5
36/11-3
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-60
36/4-48
36/4-42
36/4-30
36/4-24
36/4-24
36/4-20
36/4-18
36/4-14
36/5-18
36/5-16
36/5-14
36/5-12
36/9-24
36/9-18
36/9-16
36/9-12
36/9-10
36/9-8
36/9-8
36/9-6
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-60
36/4-48
36/4-42
36/4-36
36/4-30
36/4-24
36/4-20
36/4-18
36/5-24
36/5-20
36/9-48
36/9-42
36/9-30
36/9-24
36/9-20
36/11-24
36/11-18
36/11-12
36/4-60
36/4-48
36/4-42
36/4-36
36/4-30
36/4-24
36/4-20
36/4-18
36/4-16
36/4-14
36/4-12
36/5-14
36/5-12
36/9-24
36/9-20
36/9-16
36/9-14
36/9-12
36/9-10
36/9-8
36/9-7
36/9-6
36/11-7
36/11-6
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-60
36/4-48
36/4-42
36/4-36
36/4-30
36/4-24
36/4-20
36/4-20
36/4-16
36/4-14
36/5-18
36/5-14
36/5-12
36/9-24
36/9-20
36/9-18
36/9-14
36/9-12
36/9-10
36/9-8
36/9-8
36/11-7
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-60
36/4-48
36/4-48
36/4-36
36/4-30
36/4-30
36/4-24
36/4-20
36/4-18
36/4-14
36/5-18
36/5-16
36/5-14
36/5-12
36/7-14
36/9-18
36/9-16
36/9-12
36/7-8
36/9-8
36/9-6
36/11-6
* Please refer to footnotes listed at the end of this section on page 144.
Allowable
Diaphragm Design
Strength, plf*
SASD
SASD
(wind)
(seismic)
194
206
207
221
222
236
237
253
254
270
272
289
291
309
311
331
333
354
356
379
381
406
408
434
437
464
467
497
500
532
535
569
572
609
612
651
655
697
701
746
750
798
802
854
859
914
919
977
983
1046
1052
1119
1204
1281
1379
1467
1579
1679
1807
1923
Span = 6'-6''
Recommended Hilti Powder-Actuated Frame Fastener Pattern-Sidelap Spacing Hilti SLC (in. o.c.)*
X-ENP-19 with tf 1/4"
22 ga.
20 ga.
18 ga.
16 ga.
22 ga.
20 ga.
18 ga.
22 ga.
20 ga.
18 ga.
36/3-72
36/3-72
36/3-60
36/3-48
36/3-36
36/3-30
36/3-24
36/3-20
36/3-18
36/3-16
36/4-20
36/4-16
36/4-14
36/5-18
36/5-14
36/5-12
36/4-8
36/5-10
36/5-8
36/5-7
36/9-12
36/9-10
36/9-8
36/9-8
36/9-6
36/11-7
36/9-4
36/11-4
36/11-3
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-60
36/3-48
36/3-36
36/3-30
36/3-24
36/3-24
36/3-20
36/3-16
36/4-20
36/4-18
36/4-14
36/5-18
36/5-16
36/5-14
36/5-12
36/5-10
36/5-8
36/5-7
36/9-12
36/7-8
36/9-8
36/9-6
36/9-4
36/11-4
36/3-78
36/3-78
36/3-78
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-60
36/3-48
36/3-36
36/3-30
36/3-24
36/3-20
36/3-18
36/3-16
36/4-20
36/4-18
36/4-14
36/5-18
36/5-16
36/5-12
36/5-12
36/5-10
36/5-8
36/9-12
36/7-7
36/9-7
36/9-5
36/3-78
36/3-78
36/3-78
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-60
36/3-48
36/3-42
36/3-36
36/3-30
36/3-24
36/3-20
36/3-16
36/3-14
36/4-18
36/4-16
36/4-14
36/4-12
36/5-14
36/5-12
36/5-10
36/9-20
36/9-14
36/9-10
36/9-7
36/11-7
36/3-60
36/3-48
36/3-42
36/3-30
36/3-24
36/3-24
36/3-20
36/3-16
36/3-14
36/4-18
36/4-14
36/5-18
36/5-16
36/5-12
36/5-12
36/5-10
36/9-18
36/9-14
36/9-12
36/9-10
36/9-8
36/9-8
36/9-7
36/9-6
36/9-5
36/11-5
36/11-4
36/11-3
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-60
36/4-48
36/4-42
36/4-36
36/4-30
36/4-24
36/4-20
36/4-20
36/4-16
36/4-14
36/5-18
36/5-14
36/5-12
36/9-24
36/9-20
36/9-16
36/9-14
36/9-12
36/9-10
36/9-8
36/9-6
36/11-6
36/4-78
36/4-78
36/4-78
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-48
36/4-48
36/4-36
36/4-30
36/4-24
36/4-24
36/4-20
36/4-18
36/5-20
36/5-18
36/9-42
36/9-30
36/9-24
36/9-20
36/9-18
36/11-20
36/11-14
36/4-60
36/4-48
36/4-48
36/4-36
36/4-30
36/4-24
36/4-24
36/4-20
36/4-18
36/4-16
36/5-18
36/5-16
36/5-14
36/5-12
36/9-20
36/9-18
36/9-14
36/9-12
36/9-10
36/7-7
36/9-8
36/9-7
36/9-6
36/11-7
36/11-6
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-60
36/4-48
36/4-42
36/4-30
36/4-30
36/4-24
36/4-20
36/4-18
36/4-16
36/4-14
36/4-12
36/5-14
36/5-12
36/7-14
36/9-18
36/9-16
36/9-14
36/9-12
36/9-10
36/9-8
36/9-6
36/11-6
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-60
36/4-48
36/4-42
36/4-36
36/4-30
36/4-24
36/4-24
36/4-20
36/4-18
36/4-14
36/5-18
36/5-16
36/5-14
36/5-12
36/7-14
36/7-12
36/9-14
36/9-12
36/7-7
36/9-7
36/11-7
* Please refer to footnotes listed at the end of this section on page 144.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 141
Span = 7'-0''
Recommended Hilti Powder-Actuated Frame Fastener Pattern-Sidelap Spacing Hilti SLC (in. o.c.)*
X-ENP-19 with tf 1/4"
22 ga.
20 ga.
18 ga.
16 ga.
22 ga.
20 ga.
18 ga.
22 ga.
20 ga.
18 ga.
36/3-72
36/3-60
36/3-48
36/3-42
36/3-36
36/3-30
36/3-24
36/3-20
36/3-18
36/3-14
36/4-18
36/4-16
36/4-14
36/4-12
36/5-14
36/5-12
36/5-10
36/9-18
36/5-8
36/5-7
36/5-6
36/9-10
36/9-8
36/9-7
36/9-6
36/11-7
36/11-5
36/11-4
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-60
36/3-48
36/3-42
36/3-36
36/3-30
36/3-24
36/3-20
36/3-18
36/3-16
36/4-20
36/4-16
36/4-14
36/4-12
36/5-14
36/5-12
36/4-8
36/5-10
36/5-8
36/9-14
36/9-12
36/9-10
36/9-8
36/9-6
36/11-5
36/11-4
36/3-84
36/3-84
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-60
36/3-48
36/3-42
36/3-36
36/3-30
36/3-24
36/3-20
36/3-18
36/3-14
36/4-20
36/4-16
36/4-14
36/4-12
36/5-14
36/5-12
36/5-10
36/5-10
36/5-8
36/9-12
36/9-8
36/9-6
36/9-5
36/3-84
36/3-84
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-60
36/3-48
36/3-36
36/3-30
36/3-24
36/3-24
36/3-20
36/3-16
36/3-14
36/4-18
36/4-16
36/4-14
36/4-12
36/5-14
36/5-12
36/5-10
36/9-18
36/9-12
36/9-10
36/9-7
36/11-7
36/3-48
36/3-48
36/3-36
36/3-30
36/3-24
36/3-20
36/3-18
36/3-16
36/4-20
36/4-16
36/4-14
36/4-12
36/5-14
36/5-12
36/5-10
36/5-10
36/9-16
36/9-14
36/9-12
36/9-10
36/9-8
36/9-7
36/11-8
36/9-6
36/9-5
36/11-5
36/11-4
36/11-3
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-60
36/4-48
36/4-48
36/4-36
36/4-30
36/4-30
36/4-24
36/4-20
36/4-18
36/4-16
36/4-14
36/4-12
36/5-14
36/5-12
36/9-20
36/9-18
36/9-16
36/9-12
36/9-10
36/9-10
36/9-8
36/11-8
36/11-6
36/4-84
36/4-84
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-60
36/4-48
36/4-42
36/4-36
36/4-30
36/4-24
36/4-20
36/4-20
36/5-24
36/5-20
36/5-18
36/9-36
36/7-16
36/9-24
36/9-20
36/11-20
36/11-18
36/11-12
36/4-60
36/4-48
36/4-42
36/4-36
36/4-30
36/4-24
36/4-20
36/4-20
36/4-16
36/4-14
36/5-18
36/5-14
36/5-12
36/9-24
36/9-20
36/9-16
36/9-14
36/9-12
36/9-10
36/7-7
36/9-8
36/9-7
36/9-6
36/11-6
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-60
36/4-48
36/4-42
36/4-36
36/4-30
36/4-24
36/4-24
36/4-20
36/4-18
36/4-16
36/4-14
36/4-12
36/5-14
36/5-12
36/9-20
36/9-18
36/9-14
36/9-12
36/9-10
36/7-7
36/9-8
36/11-8
36/11-6
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-60
36/4-48
36/4-48
36/4-42
36/4-36
36/4-30
36/4-24
36/4-20
36/4-20
36/4-16
36/4-14
36/5-18
36/5-14
36/5-12
36/7-14
36/9-18
36/7-12
36/9-14
36/9-12
36/7-7
36/9-7
36/11-6
* Please refer to footnotes listed at the end of this section on page 144.
Allowable
Diaphragm Design
Strength, plf*
SASD
SASD
(wind)
(seismic)
181
193
194
206
207
221
222
236
237
253
254
270
272
289
291
309
311
331
333
354
356
379
381
406
408
434
437
464
467
497
500
532
535
569
572
609
612
651
655
697
701
746
750
798
802
854
859
914
919
977
983
1046
1126
1197
1289
1371
1475
1570
1689
1797
Span = 7'-6''
Recommended Hilti Powder-Actuated Frame Fastener Pattern-Sidelap Spacing Hilti SLC (in. o.c.)*
X-ENP-19 with tf 1/4"
22 ga.
20 ga.
18 ga.
16 ga.
22 ga.
20 ga.
18 ga.
22 ga.
20 ga.
18 ga.
36/3-72
36/3-72
36/3-60
36/3-48
36/3-36
36/3-30
36/3-24
36/3-24
36/3-20
36/3-18
36/3-14
36/4-18
36/4-16
36/4-14
36/5-16
36/5-14
36/5-12
36/5-10
36/5-8
36/5-8
36/5-7
36/5-6
36/7-7
36/9-8
36/9-7
36/9-6
36/11-6
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-60
36/3-48
36/3-42
36/3-36
36/3-30
36/3-24
36/3-20
36/3-18
36/3-14
36/4-18
36/4-16
36/4-14
36/5-16
36/5-14
36/5-12
36/5-10
36/9-18
36/5-8
36/5-7
36/5-6
36/9-8
36/11-8
36/9-5
36/3-90
36/3-90
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-60
36/3-48
36/3-42
36/3-30
36/3-30
36/3-24
36/3-20
36/3-18
36/3-14
36/4-18
36/4-16
36/4-14
36/5-16
36/5-14
36/5-12
36/5-10
36/9-18
36/5-7
36/9-10
36/9-7
36/11-7
36/3-90
36/3-90
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-60
36/3-48
36/3-42
36/3-36
36/3-30
36/3-24
36/3-20
36/3-20
36/3-16
36/4-20
36/4-18
36/5-20
36/5-18
36/5-16
36/5-14
36/5-12
36/5-10
36/9-14
36/7-8
36/9-8
36/9-6
36/3-60
36/3-48
36/3-42
36/3-36
36/3-30
36/3-24
36/3-20
36/3-18
36/3-14
36/4-18
36/4-16
36/4-14
36/5-16
36/5-14
36/5-12
36/5-10
36/9-18
36/5-8
36/5-7
36/9-10
36/9-10
36/9-8
36/9-7
36/11-8
36/11-7
36/9-5
36/11-4
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-60
36/4-48
36/4-42
36/4-36
36/4-30
36/4-24
36/4-24
36/4-20
36/4-18
36/4-16
36/4-14
36/5-16
36/5-14
36/5-12
36/9-20
36/9-16
36/9-14
36/9-12
36/9-10
36/7-7
36/9-7
36/11-6
36/4-90
36/4-90
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-60
36/4-48
36/4-48
36/4-36
36/4-30
36/4-30
36/4-24
36/4-20
36/4-18
36/5-20
36/5-20
36/9-36
36/7-18
36/7-16
36/7-14
36/9-18
36/11-20
36/11-14
36/4-60
36/4-48
36/4-42
36/4-36
36/4-30
36/4-30
36/4-24
36/4-20
36/4-18
36/4-16
36/5-20
36/5-16
36/5-14
36/5-12
36/7-14
36/9-18
36/9-16
36/9-12
36/9-12
36/9-10
36/9-8
36/9-7
36/11-8
36/9-6
36/11-6
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-60
36/4-48
36/4-48
36/4-42
36/4-36
36/4-30
36/4-24
36/4-20
36/4-20
36/4-18
36/5-20
36/5-18
36/5-16
36/5-12
36/5-12
36/9-18
36/9-16
36/9-14
36/9-12
36/9-10
36/7-7
36/9-7
36/11-6
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-60
36/4-48
36/4-42
36/4-36
36/4-30
36/4-30
36/4-24
36/4-20
36/4-20
36/4-16
36/5-20
36/5-16
36/5-14
36/5-12
36/7-14
36/9-18
36/9-14
36/7-10
36/9-10
36/9-7
36/11-7
* Please refer to footnotes listed at the end of this section on page 144.
142 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Span = 8'-0''
Recommended Hilti Powder-Actuated Frame Fastener Pattern-Sidelap Spacing Hilti SLC (in. o.c.)*
X-ENP-19 with tf 1/4"
22 ga.
20 ga.
18 ga.
16 ga.
22 ga.
20 ga.
18 ga.
22 ga.
20 ga.
18 ga.
36/3-72
36/3-60
36/3-48
36/3-42
36/3-36
36/3-30
36/3-24
36/3-20
36/3-20
36/3-16
36/4-20
36/4-16
36/5-20
36/5-16
36/5-14
36/4-10
36/5-12
36/5-10
36/5-8
36/5-8
36/9-12
36/9-10
36/7-7
36/9-8
36/9-7
36/9-6
36/11-5
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-60
36/3-48
36/3-42
36/3-36
36/3-30
36/3-24
36/3-24
36/3-20
36/3-18
36/4-20
36/4-18
36/4-16
36/4-14
36/5-16
36/5-14
36/5-12
36/5-10
36/5-8
36/5-8
36/5-7
36/7-8
36/9-8
36/9-6
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-60
36/3-48
36/3-42
36/3-36
36/3-30
36/3-24
36/3-24
36/3-20
36/4-24
36/4-20
36/4-18
36/4-16
36/4-14
36/5-16
36/5-14
36/5-12
36/5-10
36/5-8
36/5-7
36/7-7
36/9-7
36/9-5
36/3-96
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-60
36/3-48
36/3-42
36/3-36
36/3-30
36/3-24
36/3-20
36/3-18
36/3-16
36/4-20
36/4-16
36/5-20
36/5-16
36/5-14
36/4-10
36/5-10
36/5-10
36/7-10
36/7-8
36/9-8
36/9-6
36/3-48
36/3-48
36/3-36
36/3-30
36/3-24
36/3-24
36/3-20
36/3-18
36/4-20
36/4-18
36/4-16
36/4-14
36/5-16
36/5-14
36/5-12
36/5-10
36/9-16
36/5-8
36/9-12
36/9-10
36/7-7
36/9-8
36/9-7
36/9-6
36/9-5
36/11-6
36/11-4
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-60
36/4-48
36/4-42
36/4-36
36/4-36
36/4-30
36/4-24
36/4-20
36/4-20
36/4-18
36/5-20
36/5-18
36/4-12
36/5-12
36/5-12
36/9-18
36/9-16
36/9-14
36/9-12
36/9-10
36/7-7
36/9-7
36/11-6
36/4-96
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-60
36/4-60
36/4-48
36/4-42
36/4-36
36/4-30
36/4-24
36/4-24
36/4-20
36/4-18
36/5-20
36/5-18
36/7-18
36/7-16
36/9-24
36/9-20
36/7-12
36/11-18
36/11-12
36/4-48
36/4-48
36/4-42
36/4-36
36/4-30
36/4-24
36/4-24
36/4-20
36/4-18
36/4-16
36/4-14
36/5-16
36/5-14
36/5-12
36/9-20
36/7-12
36/9-14
36/9-12
36/9-10
36/9-10
36/9-8
36/9-7
36/11-8
36/11-7
36/11-6
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-60
36/4-48
36/4-42
36/4-36
36/4-30
36/4-30
36/4-24
36/4-20
36/4-20
36/4-16
36/5-20
36/5-16
36/5-14
36/5-12
36/7-14
36/9-18
36/9-14
36/7-10
36/9-12
36/9-10
36/7-7
36/9-7
36/11-6
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-60
36/4-48
36/4-48
36/4-42
36/4-36
36/4-30
36/4-24
36/4-24
36/4-20
36/4-18
36/4-16
36/4-14
36/5-16
36/5-14
36/5-12
36/7-14
36/7-12
36/9-14
36/7-10
36/9-10
36/9-7
36/11-7
* Please refer to footnotes listed at the end of this section on page 144.
Allowable
Diaphragm Design
Strength, plf*
SASD
SASD
(wind)
(seismic)
169
180
181
193
194
206
207
221
222
236
237
253
254
270
272
289
291
309
311
331
333
354
356
379
381
406
408
434
437
464
467
497
500
532
535
569
572
609
612
651
655
697
701
746
750
798
802
854
859
914
919
977
1052
1119
1204
1281
1379
1467
1579
1679
Span = 9'-6''
Recommended Hilti Powder-Actuated Frame Fastener Pattern-Sidelap Spacing Hilti SLC (in. o.c.)*
X-ENP-19 with tf 1/4"
22 ga.
20 ga.
18 ga.
16 ga.
22 ga.
20 ga.
18 ga.
22 ga.
20 ga.
18 ga.
36/3-72
36/3-60
36/3-48
36/3-42
36/3-36
36/3-30
36/3-30
36/3-24
36/3-20
36/3-18
36/3-16
36/4-18
36/4-16
36/4-14
36/5-16
36/5-14
36/4-10
36/5-10
36/5-10
36/5-8
36/9-12
36/9-10
36/7-7
36/9-8
36/9-7
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-60
36/3-48
36/3-48
36/3-42
36/3-36
36/3-30
36/3-24
36/3-20
36/3-20
36/3-16
36/4-20
36/4-16
36/4-14
36/5-16
36/4-12
36/4-10
36/5-12
36/5-10
36/5-8
36/5-8
36/5-7
36/7-7
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-60
36/3-48
36/3-48
36/3-36
36/3-36
36/3-30
36/3-24
36/3-20
36/3-18
36/3-16
36/4-20
36/4-16
36/4-14
36/5-16
36/4-12
36/4-10
36/5-12
36/5-10
36/5-8
36/9-10
36/9-8
36/9-6
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-60
36/3-48
36/3-42
36/3-36
36/3-30
36/3-24
36/3-24
36/3-20
36/3-18
36/4-20
36/4-18
36/4-16
36/4-14
36/5-16
36/5-14
36/5-12
36/5-10
36/5-8
36/9-10
36/7-7
36/11-8
36/3-48
36/3-48
36/3-42
36/3-36
36/3-30
36/3-24
36/3-20
36/3-20
36/3-16
36/4-18
36/4-16
36/4-14
36/5-16
36/5-14
36/4-10
36/5-10
36/5-10
36/9-14
36/5-8
36/5-7
36/9-10
36/9-8
36/9-7
36/9-7
36/9-6
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-60
36/4-48
36/4-42
36/4-42
36/4-36
36/4-30
36/4-24
36/4-24
36/4-20
36/4-18
36/4-16
36/4-14
36/5-16
36/5-14
36/5-12
36/9-18
36/9-16
36/9-14
36/9-12
36/9-10
36/9-10
36/9-7
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-60
36/4-48
36/4-48
36/4-42
36/4-36
36/4-30
36/4-30
36/4-24
36/4-20
36/4-20
36/4-18
36/5-20
36/7-20
36/7-18
36/7-16
36/9-20
36/9-18
36/11-18
36/11-14
36/4-48
36/4-48
36/4-42
36/4-36
36/4-30
36/4-30
36/4-24
36/4-20
36/4-20
36/4-18
36/4-16
36/4-14
36/4-12
36/5-14
36/5-12
36/9-18
36/9-14
36/7-10
36/9-12
36/9-10
36/9-8
36/9-8
36/9-7
36/9-6
36/11-6
36/4-72
36/4-72
36/4-72
36/4-72
36/4-60
36/4-60
36/4-48
36/4-42
36/4-36
36/4-36
36/4-30
36/4-24
36/4-24
36/4-20
36/4-18
36/4-16
36/4-14
36/5-16
36/5-14
36/5-12
36/9-18
36/9-16
36/9-14
36/9-12
36/9-10
36/9-8
36/9-7
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-60
36/4-60
36/4-48
36/4-42
36/4-36
36/4-30
36/4-30
36/4-24
36/4-24
36/4-20
36/4-18
36/4-16
36/4-14
36/5-16
36/5-14
36/5-12
36/7-14
36/9-16
36/9-14
36/9-10
36/9-8
36/11-8
36/11-6
* Please refer to footnotes listed at the end of this section on page 144.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 143
Span = 10'-0''
Recommended Hilti Powder-Actuated Frame Fastener Pattern-Sidelap Spacing Hilti SLC (in. o.c.)*
X-ENP-19 with tf 1/4"
22 ga.
20 ga.
18 ga.
16 ga.
22 ga.
20 ga.
18 ga.
22 ga.
20 ga.
18 ga.
36/3-72
36/3-72
36/3-72
36/3-60
36/3-48
36/3-48
36/3-42
36/3-36
36/3-30
36/3-24
36/3-24
36/3-20
36/3-18
36/3-16
36/4-18
36/4-16
36/4-14
36/4-12
36/4-10
36/5-12
36/5-10
36/9-14
36/5-8
36/5-7
36/9-10
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-60
36/3-48
36/3-48
36/3-42
36/3-36
36/3-30
36/3-24
36/3-24
36/3-20
36/3-18
36/3-16
36/4-18
36/4-16
36/4-14
36/5-16
36/5-14
36/4-10
36/5-10
36/5-10
36/9-12
36/3-120
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-60
36/3-48
36/3-48
36/3-42
36/3-36
36/3-30
36/3-24
36/3-24
36/3-20
36/3-18
36/3-16
36/4-18
36/4-16
36/4-14
36/5-16
36/5-14
36/5-10
36/9-14
36/9-10
36/7-7
36/3-120
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-72
36/3-60
36/3-48
36/3-48
36/3-42
36/3-36
36/3-30
36/3-24
36/3-24
36/3-20
36/3-16
36/4-20
36/4-18
36/4-16
36/4-14
36/5-16
36/5-12
36/9-14
36/9-12
36/7-7
36/3-72
36/3-60
36/3-48
36/3-48
36/3-42
36/3-36
36/3-30
36/3-24
36/3-24
36/3-20
36/4-24
36/3-16
36/4-18
36/4-16
36/4-14
36/5-16
36/5-14
36/4-10
36/5-10
36/5-10
36/9-14
36/9-12
36/9-10
36/9-8
36/9-8
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-60
36/4-48
36/4-48
36/4-42
36/4-36
36/4-30
36/4-30
36/4-24
36/4-20
36/4-20
36/4-18
36/4-16
36/4-14
36/5-16
36/5-14
36/5-12
36/9-16
36/9-14
36/7-10
36/9-10
36/4-120
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-60
36/4-60
36/4-48
36/4-42
36/4-36
36/4-36
36/4-30
36/4-24
36/4-24
36/4-20
36/4-18
36/5-20
36/5-18
36/7-18
36/9-24
36/9-20
36/7-12
36/11-14
36/4-72
36/4-60
36/4-60
36/4-48
36/4-42
36/4-36
36/4-36
36/4-30
36/4-24
36/4-24
36/4-20
36/4-18
36/4-16
36/4-14
36/5-16
36/4-12
36/5-12
36/9-18
36/9-16
36/9-14
36/7-10
36/9-10
36/9-10
36/9-8
36/9-7
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-60
36/4-48
36/4-48
36/4-42
36/4-36
36/4-30
36/4-30
36/4-24
36/4-20
36/4-20
36/4-18
36/4-16
36/4-14
36/5-16
36/5-14
36/5-12
36/9-16
36/9-14
36/7-10
36/9-10
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-72
36/4-60
36/4-60
36/4-48
36/4-48
36/4-42
36/4-36
36/4-30
36/4-30
36/4-24
36/4-20
36/4-20
36/4-18
36/4-16
36/5-18
36/5-16
36/5-14
36/5-12
36/7-12
36/9-12
36/9-8
36/9-7
SASD (seismic) values calculated by using a safety factor () of 2.50 for seismic loads. For SLRFD (seismic), multiply SASD (seismic) by 2.50 and then by a resistance factor ()
of 0.65. For SLSD (seismic), multiply SASD (seismic) by 2.50 and then by a resistance factor () of 0.60.
SASD (wind) values calculated by using a safety factor () of 2.35 for seismic loads. For SLRFD (wind), multiply SASD (wind) by 2.35 and then by a resistance factor () of
0.70. For SLSD (wind), multiply SASD (wind) by 2.35 and then by a resistance factor () of 0.65.
Tabulated fastening patterns apply to standard (Fy 33 ksi; Fu 45 ksi) or high strength (Fy 80 ksi; Fu 92 ksi) 1-1/2" deep, 6" center-to-center types B and BI
steel deck.
At diaphragm perimeter, Hilti powder-actuated frame fasteners should be spaced at identical spacing as sidelap connectors.
Panel buckling has been checked. Diaphragm shear stiffness should be calculated separately. Refer to Section 3.5.1.8.
Interpolation of diaphragm shear strength values is allowed between span dimensions, sidelap spacings and deck gauge. Alternatively, use calculations as
discussed in Section 3.5.1.8 to determine diaphragm shear capacities directly.
8 Additional diaphragm fastening patterns and optimized attachment options can be developed from Hilti Profis DF Diaphragm Software version 2.0.
Contact Hilti Technical Services or find more information at www.us.hilti.com/decking (USA) or www.hilti.ca/decking (Canada).
9
To convert from sidelap spacing (SS) to sidelaps per span (SPS), use the following formula: SPS=((span,ft) x 12)/(SS, in.). Round up to the next whole sidelap
connector.
10 For 16 gauge steel deck or for high tensile strength (fu > 65 ksi) 18 gauge steel deck, use S-SLC 02 M HWH. For more information on Hilti Sidelap Connectors
refer to Section 3.5.4.
11 For diaphragm shear load values using Hilti #10 HWH screws, use the Hilti Profis DF Diaphragm software or contact Hilti at 877-749-6337 or deck@hilti.com.
144 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Product Features
Ductile connections
Minimal damage to coatings
Fast and simple installation
Install in virtually any weather
No electrical power source required
3.5.6.1
Product Description
3.5.6.2
Material Specifications
3.5.6.3
Technical Data
3.5.6.4
Installation Instructions
3.5.6.5
Ordering Information
Product Selection and Performance in Concrete Over Metal Deck Composite Floor Slabs3
X-HVB
Connector
Connector
Height, Hs
in. (mm)
Minimum Slab
Thickness, Ycon
in. (mm)
X-HVB80
3-1/8
(80)
3-11/16
(93)
1-3/4
(45)
1-3/4
(45)
X-HVB95
3-3/4
(95)
4-1/4
(108)
2-3/8
(60)
2-1/4
(57)
X-HVB110
4-5/16
(110)
4-13/16
(123)
2-15/16
(75)
2-5/8
(66)
X-HVB125
4-15/16
(125)
5-7/16
(138)
3-1/8
(80)
2-15/16
(75)
5-1/2
3-1/8
3-1/8
(140)
(152)
(80)
(80)
X-HVB140
Nominal
Shear Strength1, Qn
lb (kN)
Allowable
Shear Strength2,
q
lb (kN)
6294
(28.0)
3147
(14.0)
7868
3934
(35.0)
(17.5)
1 Nominal shear strength to be used for designs per AISC-LRFD and unfactored shear resistance per AISC design formulas.
2 Allowable shear strength to be used for designs per AISC-ASD.
3 Tabulated load values based upon installation in base steel greater than or equal to 5/16".
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 145
Number of XHVBs
in One Rib
Rg
1.00
wr
0.85
hr
0.70
wr
hr
Condition
Rg
1.5
1.00
< 1.5
0.851
Deflections
Point loads
Application of large point loads causes abrupt changes in
shear. To avoid excessive slip, additional X-HVB connectors
may be necessary between the point load and the support.
Partial shear connection
AISC-LRFD and AISC-ASD both require that the capacity
of the installed shear connectors must be no less than 25%
of the calculated shear load for full composite design. This
requirement is applicable, independent of whether welded
studs or X-HVBs are used for the shear connection.
I eff
ls
n
l tr
=
=
=
=
Is + n x ( l t r ls )
moment of inertia of steel section
connection fraction
moment of inertia with 100% connection
Continuous beams
Hilti X-HVB shear connectors are also suitable for use in
continuous composite beams. The connectors are distributed
uniformly between the point of zero moment and the point of
maximum moment.
To obtain access to Hiltis BDES Composite Design Software, which designs and analyzes composite and
non-composite beams using X-HVB shear connectors under distributed and point loads in accordance
with AISC LRFD, contact Hilti Technical Support at 1-877-749-6337.
146 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
1-9/16"
40
Wr 1-9/16"
Wr 1-9/16"
3. With one X-HVB per rib, the leg may be either centered in
the rib or positioned to give a 1-9/16" (40 mm) clearance to
the side of the rib.
2"
50
2"
50
4"
100
2"
4"
100
>> 4"
100
51
4. With two or three X-HVBs per rib, the legs may be either
centered in the rib or alternated about the center.
m = spacing of ribs
50
2"
Ycon
4Y
or 24"
conor 600
4d
4"
100
Qty/Pkg
X-HVB80
X-HVB95
X-HVB110
X-HVB125
250
250
250
200
DX-76
X-76-F-HVB Baseplate
X-76-P-HVB Piston
X-76-PS Stop Ring
* X-HVB shear connectors must be fastened with the X-76-F-HVB fastener guide, the
X-76-P-HVB piston and the X-ENP-21 HVB fastener (sold separately)
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 147
Hole Diameter
Larger than Screw Threads
Top Material
Void or Insulation
Bottom Material to be Drilled
Drill Flute
Drilling Through
Wood to Metal
Point Length
The unthreaded
section from the
Point
point to the first
Length
thread should be long
enough to assure
the drilling action is
complete before the
first thread engages the drilled metal.
Screw threads advance at a rate of up
to ten times faster than the drill flute
can remove metal. All drilling therefore
should be complete before threads
begin to form.
If your application
calls for drilling
through wood over
1/2" thick, a clearance
hole is required.
Select a fastener with
breakaway wings for this type of job.
The wings will ream a clearance hole
and break-off when they contact metal
surface (minimum metal thickness
0.06") to be drilled.
Winged
Reamer
0.500
#3 Point
#5 Point
0.500
#4 Point
0.400
0.300
0.210
0.200
0.100
0.100
0.110
0.140
0.220
0.175
0.100
0.110
0.110
0.110
#8
#10
#12
#14
0.250
0.250
0.250
0.175
0.175
#12
#14
0.035
Screw
Diameter
#6, #8
#10
#12
Note: Meets or exceeds ASTM C1513. Shaded areas represent total thickness of all steel including any void spaces between layers.
148 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Gauge
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Aluminum
Sheet
Metal
(Approx. Thickness
in decimal parts
of an inch)
0.1285
0.1644
0.1144
0.1495
0.1019
0.1345
0.0907
0.1196
0.0808
0.1046
0.0720
0.0897
0.0641
0.0747
0.0571
0.0673
0.0508
0.0598
0.0493
0.0538
0.0403
0.0474
0.0359
0.0418
0.0320
0.0358
0.0285
0.0329
0.0253
0.0295
0.0226
0.0269
0.0201
0.0239
0.0179
0.0209
0.0159
0.0179
0.0142
0.0164
0.0126
0.0149
Fraction to Decimal
Fraction (in.)
Decimal
Equivalent (in.)
1/64
1/32
3/64
1/16
5/64
3/32
7/64
1/8
9/64
5/32
11/64
3/16
13/64
7/32
15/64
1/4
0.015
0.031
0.046
0.062
0.078
0.093
0.109
0.125
0.140
0.156
0.171
0.187
0.203
0.218
0.234
0.250
Screw Diameter
Number
Decimal
Equivalent (in.)
#6
#7
#8
#10
#12
1/4
5/16
0.1380
0.1510
0.1640
0.1900
0.2160
0.2500
0.3125
Thread Length
Always choose a fastener with sufficient threads to fully
engage in the base metal. For attachments to 1/4" base steel,
a self-drilling screw should have at least 1/4" of threads. It is
helpful, but not critical, that the threads also engage in the
material being fastened. The head of the fastener provides
the bearing force for the material being fastened, while the
threads provide the clamping force in the base material.
Clamping
Material Being Fastened
Base Material
Threading
Thread Pitch
The thickness of material being fastened and diameter of
the screw determine the type of thread pitch to be used.
In general, the thinner the fastened materials, the fewer the
number of threads. The thicker the material, the greater
the number of threads. This principle is due to two primary
methods of thread engagement/holding power: Clamping
and Threading. In light gauge metal, the materials are actually
being clamped together by the upper and
lower
threads.
Clamping
Thread Engagement
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 149
HWH (HHWH)
(High) Hex Washer
Head : Washer face
provides a bearing
surface for the driving
sockets.
PPH (PPFH)
Phillips Pan
(Framing) Head:
Conventional head for
general applications
and provides low
profile fastening.
PFH
Phillips Flat Head:
Used primarily in
wood to countersink
and seat flush without
splintering the wood.
PWH
Phillips Wafer Head:
Large head provides
the bearing surface
necessary to seat
flush in soft materials.
PBH
Phillips Bugle Head:
Used primarily for
fastening drywall,
plywood or insulation
board to steel studs.
PTH (MPTH)
(Modified) Phillips
Truss Head: Large
head and low profile
provides surface area
needed to attach wire
lath to metal stud.
PPCH
Phillips Pancake
Conventional Head:
Head for general
applications and
provides low and
flat profile.
PFTH
Phillips Flat Truss
Head: Lowest profile
head available for
attaching metal
to metal.
PFHUC
Pancake Framing
Head Undercut: Used
for countersinking
where a full head
taper would cause
stand-off of the screw.
SHWH
Slotted Hex Washer
Head: Hex washer
head with slot in
center to provide
additional drive
connection.
MF
MT
MT
MF
150 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Environment
Low
Indoor - Dry:
no moisture exposure
Medium
Indoor and Exterior - Dry:
minimal moisture exposure
High
Indoor and Exterior - Wet:
Heavy industrial or coastal areas
with high prolonged moisture levels
but no direct exposure to chlorides,
and average temperatures
below 86 F (30 C).
Connection
Type
Untreated
Lumber-to-steel,
steel-to-steel,
gypsum-to-steel
applications
Pressure-Treated4
or Fire-Retardant
Lumber-to-steel;
aluminum-to-steel;
dissimilar metals
Untreated
Lumber-to-steel,
steel-to-steel,
gypsum-to-steel
applications;
cement
board-to-steel
Pressure-Treated4
or Fire-Retardant
Lumber-to-steel;
aluminum-to-steel;
dissimilar metals
Screw
Fastener
Descriptions
Hardened Carbon
Steel fasteners with
electro-galvanized
(min. 5 - 13
microns), black
phosphate
coatings
Carbon Steel,
two-step heat
treated fasteners
with Kwik-Cote
coating
Hardened Carbon
Steel fasteners
with Kwik-Cote
coating
Carbon Steel,
two-step heat
treated fasteners
with Kwik-Cote
coating
300 series5
stainless steel fastener
Hilti
Kwik-Flex
Hilti
Bi-Metal
Kwik-Flex
Section
3.6.4
Section
3.6.5
Screw
Fastener
Designation
Hilti Zinc
Plated Screws
Hilti
Kwik-Flex
Hilti
Self-Drilling Screws
with Kwik-Cote
or Kwik-Seal
Designation
Product
Technical
Guide Section
Section
3.6.2 or 3.6.3
Section
3.6.4
Section
3.6.2
Untreated
Lumber-to-steel,
steel-to-steel,
gypsum-to-steel
applications
Pressure-Treated4
or Fire-Retardant
Lumber-to-steel;
aluminum-to-steel;
dissimilar metals
1 If the moisture content of Pressure-Treated Lumber is high (> 18%) or unknown, stainless steel fasteners are recommended. Select appropriate stainless steel
grade for your application.
2 Guidelines based on fastener coating /material resistance to environmental corrosion (commonly called rusting) and fastener hardening process/ resistance to
hydrogen assisted stress corrosion cracking (HASCC). Evaluate site conditions which may affect these guidelines, such as: corrosive agents other than those
listed; expected service life; other (non-environmental) types of corrosion, etc
3 In highly corrosive environments (such as direct exposure to chlorides with average temperatures above 86 F (30 C)) it is generally recommended that a Highly
Corrosive Resistant (HCR) fastener be used. Contact Hilti Technical Support at 877-749-6337 for more information.
4 Pressure treated lumber refers to lumber such as SBX/DOT, Zinc borated ACQ, CA-B, CBA-A treated lumber.
5 Most 400 series stainless steels, such as 410 stainless steel, 410 super-passivated stainless steel and 400 modified stainless steel are generally considered
susceptible to HASCC. Moreover, these grades of stainless steel are 18/0 they contain chromium but no nickel which reduces corrosion resistance significantly
when compared to 18/8 grades (302, 304) or 18/8/2 grade (316).
6 The decision as to which fastener optimally meets the demands of a specific application is ultimately the judgment of the Engineer of Record or other responsible
person for the project.
7 Reference Section 2.3.3.1 for more information on corrosion resistance.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 151
Magnetic Nut
Setter Size
1/4"
5/16"
5/16"
3/8"
Phillips
Bit Size
2
2
3
3
The Hilti SD 2500 siding edition features a 2,500 rpm motor for
fastening self-drilling screws in steel up to 1/4" (6 mm) thick.
There is a depth gauge on the front of the tool for correct
depth setting of screws.
The Hilti ST 1800 heavy duty torque adjustable screwdriver
features a 1,800 rpm for fastening self-drilling screws in steel
up 1/2" (12 mm) thick. There is a depth gauge on the front of
the tool for correct depth setting of screws. There is also an
18 position adjustable torque clutch for correct torque release
setting of screws. By avoiding overdriving, proper torque
adjustment will deliver consistent fastening quality.
The ST 1800 may also be operated with the SDT 5 for a
stand-up decking system to fasten steel deck.
Please reference the table on torque considerations below
for more information on proper installation of Hilti
screw fasteners.
* These are abbreviated instructions which may vary by application.
ALWAYS review/follow the instructions accompanying the product.
TorqueConsiderationsforScrewFasteningApplications3
Soft joint applications
Applications
Suggested
Tools2
1 Whether an application requires a depth gauge or torque clutch is the judgment of the person responsible for the project. If conditions are unknown or in doubt,
use a screwdriver that features either an adjustable torque clutch or a properly adjusted depth gauge.
2 All published screw fastening connection capacities were developed using corded or cordless screwdriver tools with adjustable torque clutches. Over-driving
a screw fastener can cause a connection failure in lighter gauge and lower strength steel base materials (the threads tapping the base material are stripped by
excessive torque) or a fastener failure in heavier gauge and higher strength steel base materials (the screw is damaged or sheared by excessive torque). This
type of damage is not always visually detectable. Regardless of the tool or its torque setting, test fastenings should always be performed to verify the
appropriate torque is being applied.
3 For additional information, contact Hilti Technical Services at 877-749-6337.
152 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Product Features:
Hex head for metal-to-metal
applications
Flush head for wood-to-metal
applications
3.6.2.1
Product Description
3.6.2.2
Material Specifications
3.6.2.3
Technical Data
3.6.2.4
Installation Instructions
3.6.2.5
Ordering Information
Heat Treatment
Plating
Warning: Because of the potential for delayed hydrogen assisted stress corrosion
cracking, many hardened steel fasteners are not recommended for use with
dissimilar metals or chemically treated wood when moisture may be present or in
corrosive environments. For further information, contact Hilti Technical Support at
1-877-749-6337.
Listings/Approvals
ICC-ES (International Code Council)
ESR-2196
COLA (City of Los Angeles)
RR 25678
Nominal
Diameter
in.
#6
0.138
#7
0.151
#8
0.164
#10
0.190
#12
0.216
1/4 in.
0.250
20
(0.036)
190
(0.85)
210
(0.93)
225
(1.00)
260
(1.16)
295
(1.31)
345
(1.53)
Thickness of steel member not in contact with the screw head, ga (in.)
18
16
14
12
(0.048)
(0.060)
(0.075)
(0.105)
250
320
395
555
(1.11)
(1.42)
(1.76)
(2.47)
275
345
435
605
(1.22)
(1.53)
(1.93)
(2.69)
300
375
470
660
(1.33)
(1.67)
(2.09)
(2.94)
350
435
545
765
(1.56)
(1.93)
(2.42)
(3.40)
395
495
620
870
(1.76)
(2.20)
(2.76)
(3.87)
460
575
715
1000
(2.05)
(2.56)
(3.18)
(4.45)
10
(0.135)
715
(3.18)
780
(3.47)
845
(3.76)
980
(4.36)
1120
(4.98)
1290
(5.74)
1 The lower of the ultimate pullout, pullover, and tension fastener strength of screw should be used for design.
2 Load values based upon calculations done in accordance with Section E4 of the AISI S100.
3 AISI S100 recommends a safety factor of 3.0 be applied for allowable strength design, a factor of 0.5 be applied for LRFD design or a factor of 0.4 be
applied for LSD design.
4 ANSI/ASME standard screw diameters were used in the calculations and are listed in the tables.
5 The screw diameters in the table above are available in head styles of pan, hex washer, pancake, flat, wafer and bugle.
6 The load data in the table is based upon sheet steel with Fu = 45 ksi. For Fu = 55 ksi steel, multiply values by 1.22. For Fu = 65 ksi steel, multiply values by 1.44.
7 Refer to Section 3.6.2.5 to ensure drilling capacities.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 153
22
(0.030)
675
(3.00)
805
(3.58)
835
(3.71)
835
(3.71)
1010
(4.49)
#8
0.335
#10
0.399
#12-14
0.415
#12-24
0.415
1/4 in.
0.500
#7
0.303
#8
0.311
#10
0.364
#8
0.433
#10
0.411
#10, #12
0.409
830
(3.69)
#10
0.364
740
(3.29)
615
(2.74)
630
(2.80)
740
(3.29)
875
(3.89)
830
(3.69)
10
(0.135)
1000
(4.45)
1370
(6.09)
2325
(10.34)
3780
(16.81)
4560
(20.28)
1000
(4.45)
1000
(4.45)
1370
(6.09)
1000
(4.45)
1390
(6.18)
1370
(6.09)
2170
(9.65)
1. The lower of the ultimate pullout, pullover, and tension fastener strength of screw should be used for design.
2. Load values based upon calculations done in accordance with Section E4 of the AISI S100.
3. AISI S100 recommends a safety factor of 3.0 be applied for allowable strength design, a factor of 0.5 be applied for LRFD design or a factor of 0.4 be
applied for LSD design.
4. ANSI/ASME standard screw head diameters were used in the calculations and are listed in the tables.
5. Phillips Bugle Head (PBH) and Phillips Wafer Head (PWH) styles are not covered by this table because they are not intended for attachment of steel to steel.
6. The load data in the table is based upon sheet steel with Fu = 45 ksi. For Fu = 55 ksi steel, multiply values by 1.22. For Fu = 65 ksi steel, multiply values by 1.44.
7. Refer to Section 3.6.2.5 for drilling capacities.
Nominal
Diameter
(in.)
0.138
0.151
0.164
0.190
0.190
0.190
0.216
0.216
0.250
1 The lower of the ultimate pullout, pullover, and tension fastener strength of screw should be used
for design. The Pullout and Pullover tables in this section have already been adjusted where
screw strength governs.
2 The lower of the ultimate shear fastener strength and shear bearing should be used for design.
The Shear Bearing table in this section has already been adjusted where screw strength governs.
3 AISI S100 recommends a safety factor of 3.0 be applied for allowable strength design,
a factor of 0.5 be applied for LRFD design or a factor of 0.4 be applied for LSD design.
4 When the distance to the end of the connected part is parallel to the line of the applied force
the allowable shear fastener strength must be reduced for end distance, when necessary, in
accordance with E4.3.2 of Appendix A of AISI S100.
Torsional Strength1,2
Size
6-20
7-18
8-18
10-12
10-16
10-18
10-24
12-14
12-24
1/4-14
1/4-20
Min. Torsional
Strength
in-lb (Nm)
24
(2.7)
38
(4.3)
42
(4.8)
61
(6.9)
61
(6.9)
61
(6.9)
65
(7.3)
92
(10.4)
100
(11.3)
150
(17.0)
156
(17.6)
154 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Nominal
Diameter
in.
#7
0.151
#8
0.164
#10-12
0.190
#10-16
0.190
#10-18
0.190
#12-14
0.216
#12-24
0.216
1/4 in.
0.250
Thickness of steel
member in contact
with screw head
ga (in.)
20 (0.036)
18 (0.048)
16 (0.060)
20 (0.036)
18 (0.048)
16 (0.060)
20 (0.036)
18 (0.048)
16 (0.060)
14 (0.075)
20 (0.036)
18 (0.048)
16 (0.060)
20 (0.036)
18 (0.048)
16 (0.060)
14 (0.075)
20 (0.036)
18 (0.048)
16 (0.060)
14 (0.075)
20 (0.036)
18 (0.048)
16 (0.060)
14 (0.075)
12 (0.090)
20 (0.036)
18 (0.048)
16 (0.060)
14 (0.075)
12 (0.090)
Thickness of steel member not in contact with the screw head, ga (in.)
20 (0.036)
500
500
500
525
525
525
565
565
565
565
565
565
565
565
565
565
565
600
600
600
600
600
600
600
600
600
645
645
645
645
645
(2.22)
(2.22)
(2.22)
(2.34)
(2.34)
(2.34)
(2.51)
(2.51)
(2.51)
(2.51)
(2.51)
(2.51)
(2.51)
(2.51)
(2.51)
(2.51)
(2.51)
(2.67)
(2.67)
(2.67)
(2.67)
(2.67)
(2.67)
(2.67)
(2.67)
(2.67)
(2.87)
(2.87)
(2.87)
(2.87)
(2.87)
18 (0.048)
660
660
660
715
805
805
830
865
865
865
830
865
865
830
865
865
865
930
925
925
925
930
925
925
925
925
1020
995
995
995
995
(2.94)
(2.94)
(2.94)
(3.18)
(3.58)
(3.58)
(3.69)
(3.85)
(3.85)
(3.85)
(3.69)
(3.85)
(3.85)
(3.69)
(3.85)
(3.85)
(3.85)
(4.14)
(4.11)
(4.11)
(4.11)
(4.14)
(4.11)
(4.11)
(4.11)
(4.11)
(4.54)
(4.43)
(4.43)
(4.43)
(4.43)
16 (0.060)
660
880
890
715
955
1120
830
1110
1210
1210
830
1110
1210
830
1110
1210
1210
945
1260
1290
1290
945
1260
1290
1290
1290
1090
1400
1390
1390
1390
(2.94)
(3.91)
(3.96)
(3.18)
(4.25)
(4.98)
(3.69)
(4.94)
(5.38)
(5.38)
(3.69)
(4.94)
(5.38)
(3.69)
(4.94)
(5.38)
(5.38)
(4.20)
(5.60)
(5.74)
(5.74)
(4.20)
(5.60)
(5.74)
(5.74)
(5.74)
(4.85)
(6.23)
(6.18)
(6.18)
(6.18)
14 (0.075)
660
880
890
715
955
1170
830
1110
1390
1645
830
1110
1215
830
1110
1390
1645
945
1260
1570
1800
945
1260
1570
1800
1800
1090
1460
1820
1940
1940
(2.94)
(3.91)
(3.96)
(3.18)
(4.25)
(5.20)
(3.69)
(4.94)
(6.18)
(7.32)
(3.69)
(4.94)
(5.40)
(3.69)
(4.94)
(6.18)
(7.32)
(4.20)
(5.60)
(6.98)
(8.00)
(4.20)
(5.60)
(6.98)
(8.00)
(8.00)
(4.85)
(6.49)
(8.10)
(8.63)
(8.63)
12 (0.105)
660
880
890
715
955
1170
830
1110
1390
1645
830
1110
1215
830
1110
1390
1645
945
1260
1570
1880
945
1260
1570
1970
2285
1090
1460
1820
2280
2440
(2.94)
(3.91)
(3.96)
(3.18)
(4.25)
(5.20)
(3.69)
(4.94)
(6.18)
(7.32)
(3.69)
(4.94)
(5.40)
(3.69)
(4.94)
(6.18)
(7.32)
(4.20)
(5.60)
(6.98)
(8.36)
(4.20)
(5.60)
(6.98)
(8.76)
(10.16)
(4.85)
(6.49)
(8.10)
(10.14)
(10.85)
1 The lower of the ultimate shear bearing and shear fastener strength of screw should be used for design.
2 Load values based upon calculations done in accordance with Section E4 of AISI S100.
3 AISI S100 recommends a safety factor of 3.0 be applied for allowable strength design, a factor of 0.5 be applied for LRFD design or a factor of 0.4 be
applied for LSD design.
4 ANSI/ASME standard screw diameters were used in the calculations and are listed in the tables.
5 Load values in table are for Hex Washer Head (HWH and HHWH), Phillips Pan Head (PPH), Phillips Truss Head (PTH), Phillips Pancake Head (PPCH), and
Phillips Flat Truss Head (PFTH) style screws. Phillips Bugle Head (PBH) and Phillips Wafer Head (PWH) styles are not covered by this table because they are not
intended for attachment of steel to steel.
6 The load data in the table is based upon sheet steel with Fu = 45 ksi. For Fu = 55 ksi steel, multiply values by 1.22. For Fu = 65 ksi steel, multiply values by 1.44.
7 Refer to Section 3.6.2.5 to ensure drilling capacities.
Warning: Because of the potential for delayed hydrogen assisted stress corrosion cracking, many hardened steel fasteners
are not recommended for use with dissimilar metals or chemically treated wood when moisture may be present or in corrosive
environments. For further information, contact Hilti Technical Support at 1-877-749-6337.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 155
Description
Drilling Capacity
Min
Max
5/8"
0.018"
0.095"
3/4"
0.028"
3/8"
0.028"
Maximum Total
Thickness (MT)1
Recess
Coating2
Box Qty
3/32"
0.100"
5/16"
Zinc-3
250
0.120"
3/8"
0.375"
5/16"
Zinc-1
250
0.120"
3/16"
0.188"
5/16"
Zinc-1
250
Recess
Coating2
Box Qty
5/16"
Zinc-1
250
5/16"
Zinc-1
250
Description
Drilling Capacity
Maximum Total
Thickness (MT)1
Min
Max
0.175"
3/8"
0.375"
0.312"
3/8"
0.375"
1/2"
0.110"
1/2"
0.175"
PPH
HWH
#5 Point
Stitch
HWH
Kwik-Seal
HWH
with bonded
washer
PFH
with wings
PWH
Description
Thread
Length
Drilling Capacity
Min
Max
Maximum Total
Thickness (MT)1
Recess
Coating2
Box Qty
3/4"
0.028"
0.120"
3/8"
0.375"
5/16"
Zinc-1
3000
3/8"
0.028"
0.120"
3/16"
0.188"
5/16"
Zinc-1
6000
1/2"
0.028"
0.140"
5/16"
0.313"
5/16"
Kwik-Cote
2500
156 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Description
Thread
Length
Drilling Capacity
Min
Max
Maximum Total
Thickness (MT)1
Recess
Coating2
Box Qty
1000
1/4"
0.035"
0.100"
1/8"
0.125"
1/4"
Zinc-1
1/2"
0.035"
0.100"
3/8"
0.375"
Zinc-1
1000
1/4"
0.035"
0.100"
1/8"
0.125"
1/4"
PHL #2
Zinc-1
1000
5/16"
0.035"
0.110"
3/16"
0.188"
5/16"
Zinc-1
8500
1/2"
0.035"
0.110"
5/16"
0.313"
5/16"
Zinc-1
6500
3/4"
0.035"
0.110"
1/2"
0.500"
5/16"
Zinc-1
5000
Recess
Coating2
Box Qty
Description
S-MD 10-16x5/8 HWH #3
S-MD 10-16x3/4 HWH #3
Thread
Length
Drilling Capacity
Min
Max
Maximum Total
Thickness (MT)1
5/16"
0.110"
0.175"
3/16"
0.187"
5/16"
Zinc-1
7500
1/2"
0.110"
0.175"
3/8"
0.375"
5/16"
Zinc-1
6500
1/2"
0.110"
0.175"
3/8"
0.375"
5/16"
Zinc-1
6500
0.110"
0.175"
5/8"
0.625"
5/16"
Zinc-1
5000
3/4"
1"
0.110"
0.175"
7/8"
0.875"
5/16"
Zinc-1
4000
1-1/4"
0.110"
0.175"
1-1/8"
1.125"
Zinc-1
4000
5/16"
0.110"
0.175"
5/16"
0.313"
5/16"
PHL #2
Zinc-1
7500
1/2"
0.110"
0.175"
3/8"
0.375"
PHL #2
Zinc-1
6500
1/2"
0.110"
0.175"
5/16"
0.313"
PHL #2
Zinc-1
7500
9/16"
0.110"
0.175"
3/8"
0.375"
PHL #2
Zinc-1
7500
9/16"
0.175"
0.210"
5/16"
0.375"
0.313"
PHL #2
1/2"
0.110"
0.110"
3/8"
Zinc-2
Zinc-1
5000
5000
3/4"
0.110"
0.210"
9/16"
0.562"
5/16"
Zinc-1
3000
1-1/4"
0.110"
0.210"
1-1/16"
1.062"
5/16"
Zinc-1
2500
0.110"
0.210"
1-9/16"
1.562"
5/16"
Zinc-1
2000
0.110"
0.110"
0.210"
0.220"
1/2"
0.500"
0.313"
TX 25 HF
Zinc-3
Zinc-1
7500
4000
1-5/8"
11/16"
5/16"
1/2"
5/16"
3/8"
3/4"
0.110"
0.220"
9/16"
0.562"
3/8"
Zinc-1
3000
1-1/4"
0.110"
0.220"
1-1/16"
1.062"
3/8"
Zinc-1
2000
1-5/8"
0.110"
0.220"
1-9/16"
1.562"
3/8"
Zinc-1
1000
1/4"
0.110"
0.210"
1/8"
0.125"
5/16"
Kwik-Cote
3000
5/8"
1"
0.110"
0.210"
3/8"
0.375"
5/16"
Kwik-Cote
2500
0.110"
0.210"
5/8"
0.625"
5/16"
Kwik-Cote
2000
1-1/4"
0.110"
0.210"
7/8"
0.875"
5/16"
Kwik-Cote
2000
1-1/2"
0.110"
0.210"
1-3/8"
1.375"
5/16"
Kwik-Cote
1500
5/8"
1"
0.110"
0.220"
3/8"
0.375"
3/8"
Kwik-Cote
2000
0.110"
0.220"
7/8"
0.875"
3/8"
Kwik-Cote
1500
Warning: Because of the potential for delayed hydrogen assisted stress corrosion cracking, many hardened steel fasteners
are not recommended for use with dissimilar metals or chemically treated wood when moisture may be present or in corrosive
environments. For further information, contact Hilti Technical Support at 1-877-749-6337.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 157
Description
Thread
Length
Drilling Capacity
Min
Max
Maximum Total
Thickness (MT)1
Recess
Coating2
Box Qty
1/2"
0.175"
0.250"
3/8"
0.375"
5/16"
Zinc-1
4500
3/4"
0.175"
0.250"
5/8"
0.625"
5/16"
Zinc-1
3500
1/2"
0.250"
0.500"
7/16"
0.437"
5/16"
Zinc-1
4000
1/2"
0.250"
0.500"
5/16"
0.313"
5/16"
KwikCote
4000
1-1/4"
0.250"
0.500"
1-3/16"
1.187"
5/16"
KwikCote
2000
2-1/4"
0.250"
0.500"
2-3/16"
2.187"
5/16"
KwikCote
1000
1/2"
0.250"
0.500"
5/16"
0.313
5/16
KwikCote
2500
Description
Thread
Length
Drilling Capacity
Min
Max
Maximum Total
Thickness (MT)1
Recess
Coating2
Box Qty
1/2"
0.050"
0.140"
1/2"
0.500"
PHL #2
BP
6000
5/8"
0.050"
0.140"
3/4"
0.750"
PHL #2
BP
4000
3/4"
1"
0.050"
0.175"
5/8"
0.625"
PHL #2
Zinc-1
6000
0.050"
0.175"
7/8"
0.875"
PHL #2
Zinc-1
5000
1-1/4"
0.050"
0.175"
1-1/8"
1.125"
PHL #2
Zinc-1
3500
1"
0.050"
0.175"
3/4"
0.750"
PHL #2
Zinc-1
4000
0.050"
0.232"
1-1/4"
1.250"
PHL #2
Zinc-1
2000
1-3/8"
2"
0.050"
0.232"
1.750"
PHL #2
Zinc-1
1500
2-1/4"
0.050"
0.250"
1-3/4"
2"
2.000"
PHL #2
Zinc-1
1000
Warning: Because of the potential for delayed hydrogen assisted stress corrosion cracking, many hardened steel fasteners
are not recommended for use with dissimilar metals or chemically treated wood when moisture may be present or in corrosive
environments. For further information, contact Hilti Technical Support at 1-877-749-6337.
158 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Box Qty
Application
10,000
10,000
10,000
6 x 1-1/8 PBH SD
BP
Zinc-2
BP
Zinc-2
10,000
BP
8,000
Zinc-2
8,000
BP
5,000
Zinc-2
5,000
BP
4,000
Zinc-2
4,000
BP
2,500
Zinc-2
2,500
BP
1,600
Zinc-2
BP
Zinc-2
BP
1,600
1,400
1,400
10,000
Zinc-2
10,000
from 14 ga to 20 ga
Zinc-2
10,000
Zinc-1
7,500
Zinc-1
7,500
Zinc-2
5,000
Zinc-2
10,000
Zinc-2
Zinc-2
Zinc-2
10,000
8,000
8,000
6 x 1 PBH SD
6 x 1 PBH SD Zinc
6 x 1-1/4 PBH SD
6 x 1-1/4 PBH SD Zinc
6 x 1-5/8 PBH SD
6 x 1-5/8 PBH SD Zinc
6 x 1-7/8 PBH SD
6 x 1-7/8 PBH SD Zinc
8 x 2-3/8 PBH SD
8 x 2-3/8 PBH SD Zinc
8 x 2-5/8 PBH SD
8 x 2-5/8 PBH SD Zinc
8 x 3 PBH SD
8 x 3 PBH SD Zinc
Coating1
BP
5,000
Zinc-2
3,000
14 ga to 20 ga studs
1 For coating abbreviations, Zinc-1 = ASTM F1941; Zinc-2 = EN /ISO 4042 A3F; BP = Black Phosphate. For more information on corrosion resistance, reference
Section 3.6.1.6.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 159
Product Description
3.6.3.2
Material Specifications
3.6.3.3
Technical Data
3.6.3.4
Installation Instructions
3.6.3.5
Ordering Information
Fastener Material
Fastener Plating4
Carbon Steel
3 to 8 m Zinc
Carbon Steel
5 m Zinc1
Carbon Steel
Zinc3
Carbon Steel
5 m Zinc2
110
(0.49)
130
(0.58)
26
(0.018)
150
(0.67)
160
(0.71)
150
(0.67)
160
(0.71)
24
(0.024)
200
(0.89)
230
(1.02)
200
(0.89)
230
(1.02)
Approvals/Listings
ICC-ES (International Code Council)
ESR-2196 (S-MD HWH Self-Drilling
Screws)
COLA (City of Los Angeles)
RR 25678 (S-MD HWH Self-Drilling
Screws)
28
(0.015)
110
(0.49)
22
(0.030)
260
(1.16)
305
(1.36)
260
(1.16)
305
(1.36)
190
(0.85)
20
(0.036)
330
(1.47)
350
(1.56)
18
(0.048)
16
(0.060)
450
(2.49)
300
(1.33)
350
(1.56)
395
(1.76)
375
(1.67)
435
(1.93)
495
(2.20)
350
(1.56)
225
(1.00)
260
(1.16)
295
(1.31)
1 The lower of the ultimate pullout, pullover, and tension fastener strength of screw should be used
for determination of allowable or factored resistance loads per footnote 4.
2 Unless otherwise noted, load values based upon testing completed in accordance with AISI S905.
3 Load values based upon calculations done in accordance with Section E4 of AISI S100. ANSI/ASME
standard screw diameters were used in the calculations and are listed in the tables.
4 AISI S100 recommends a safety factor of 3.0 be applied for allowable strength design (ASD), a factor
of 0.5 be applied for LRFD design or a factor of 0.4 be applied for LSD design.
5 The load data in the table is based upon sheet steel with Fu = 45 ksi. For Fu = 55 ksi steel, multiply
values by 1.22. For Fu 65 ksi steel, multiply values by 1.44.
6 Refer to Section 3.6.3.5 to ensure optimal drilling capacities.
7 Load data for thicker steel connections available. Please reference Section 3.6.2.
160 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Washer or Head
Diameter
In.
0.335
0.399
#8 HWH Sharp
0.335
0.399
335
(1.49)
400
(1.78)
(0.018)
405
(1.80)
480
(2.14)
405
(1.80)
480
(2.14)
(0.024)
540
(2.40)
645
(2.87)
540
(2.40)
645
(2.87)
0.335
0.399
0.415
(0.030)
675
(3.00)
805
(3.58)
675
(3.00)
805
(3.58)
675
(3.00)
805
(3.58)
835
(3.71)
(0.036)
815
(3.63)
970
(4.31)
(0.048)
(0.060)
1290
(5.74)
1000
(4.45)
1290
(5.74)
1340
(5.96)
1000
(4.45)
1370
(6.09)
1680
(7.47)
970
(4.31)
815
(3.63)
970
(4.31)
1010
(4.49)
1 The lower of the ultimate pullout, pullover, and tension fastener strength of screw should be used for determination of allowable or
factored resistance loads per footnote 4.
2 Unless noted otherwise, load values based upon calculations done in accordance with Section E4 of AISI S100. ANSI/ASME standard screw head diameters were used in the calculations and are listed in the tables.
3 Load values based upon testing completed in accordance with AISI S905.
4 AISI S100 recommends a safety factor of 3.0 be applied for allowable strength design (ASD), a factor of 0.5 be applied for LRFD
design and a factor of 0.4 be applied for LSD design.
5 The load data in the table is based upon sheet steel with Fu = 45 ksi. For Fu = 55 ksi steel, multiply values by 1.22. For Fu 65 ksi
steel, multiply values by 1.44.
6 Refer to Section 3.6.3.5 to ensure optimal drilling capacities.
7 Load data for thicker steel connections available. Please reference Section 3.6.2.
Nominal
Diameter
In.
0.164
0.190
0.164
0.190
0.164
0.190
0.216
(kN)1
(8.52)
(8.52)
(7.16)
(8.52)
(4.45)
(6.09)
(10.34)
Shear Pss
lb
1570
1905
860
1905
1170
1215
1880
(kN)2,3
(6.98)
(8.47)
(3.83)
(8.47)
(5.20)
(5.40)
(8.36)
1 The lower of the ultimate pullout, pullover, and tension fastener strength of
screw should be used for design. The Pullout and Pullover tables in this section
have already been adjusted where screw strength governs.
2 The lower of the ultimate shear fastener strength and shear bearing should
be used for design. The Shear Bearing table in this section has already been
adjusted where screw strength governs.
3 AISI S100 recommends a safety factor of 3.0 be applied for allowable strength
design (ASD), a factor of 0.5 be applied for LRFD design or a factor of 0.4
be applied for LSD design.
4 When the distance to the end of the connected part is parallel to the line of
the applied force, the allowable shear fastener strength must be reduced for
end distance, when necessary, in accordance with E4.3.2 of Appendix A of
AISI S100.
Torsional Strength1,2
Min. Torsional
Strength
in-lb (Nm)
S-MS 8-18
57
(6.4)
S-MS 10-12
92 (10.4)
#8 HWH Sharp
42
(4.8)
#10 HWH Sharp
61
(6.9)
S-MD 8-18
42
(4.8)
S-MD 10-16
61
(6.9)
S-MD 12-14
92 (10.4)
Screw
Designation
Warning: Because of the potential for delayed hydrogen assisted stress corrosion cracking, many hardened steel fasteners
are not recommended for use with dissimilar metals or chemically treated wood when moisture may be present or in corrosive
environments. For further information, contact Hilti Technical Support at 1-877-749-6337.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 161
115 (0.51)
115 (0.51)
115 (0.51)
115 (0.51)
115 (0.51)
115 (0.51)
115 (0.51)
115 (0.51)
115 (0.51)
26
(0.018)
260 (1.16)
270 (1.20)
270 (1.20)
345 (1.53)
345 (1.53)
230 (1.02)
230 (1.02)
330 (1.47)
365 (1.62)
365 (1.62)
115 (0.51)
275 (1.22)
275 (1.22)
275 (1.22)
115 (0.51)
275 (1.22)
275 (1.22)
275 (1.22)
275 (1.22)
24
(0.024)
315 (1.40)
340 (1.51)
445 (1.98)
445 (1.98)
555 (2.47)
375 (1.67)
410 (1.82)
500 (2.22)
500 (2.22)
570 (2.54)
115 (0.51)
275 (1.22)
425 (1.89)
425 (1.89)
115 (0.51)
275 (1.22)
440 (1.96)
440 (1.96)
440 (1.96)
22
(0.030)
320 (1.42)
340 (1.51)
475 (2.11)
555 (2.47)
710 (3.16)
455 (2.02)
570 (2.54)
685 (3.05)
685 (3.05)
725 (3.22)
115 (0.51)
275 (1.22)
425 (1.89)
610 (2.71)
115 (0.51)
275 (1.22)
440 (1.96)
715 (3.18)
715 (3.18)
400 (1.78)
400 (1.78)
400 (1.78)
400 (1.78)
20
18
16
(0.036)
(0.048)
(0.060)
320 (1.42)
340 (1.51)
475 (2.11)
555 (2.47)
860 (3.83)
115 (0.51)
275 (1.22)
440 (1.96)
715 (3.18)
895 (3.98)
1 The lower of the ultimate shear bearing and shear fastener strength of screw should be used for determination of allowable or factored resistance loads
per footnote 4.
2 Unless otherwise noted, load values based upon testing completed in accordance with AISI S905.
3 Load values based upon calculations done in accordance with Section E4 of AISI S100. ANSI/ASME standard screw diameters were used in the calculations.
4 AISI S100 recommends a safety factor of 3.0 be applied for allowable strength design (ASD), a factor of 0.5 be applied for LRFD design or a factor of 0.4 be
applied for LSD design.
5 The load data in the table is based upon sheet steel with Fu = 45 ksi. For Fu = 55 ksi steel, multiply values by 1.22. For Fu 65 ksi steel, multiply values by 1.44.
6 Refer to Section 3.6.3.5 to ensure optimal drilling capacities.
7 Load data for thicker steel connections available. Please reference Section 3.6.2.
Warning: Because of the potential for delayed hydrogen assisted stress corrosion cracking, many hardened steel fasteners
are not recommended for use with dissimilar metals or chemically treated wood when moisture may be present or in corrosive
environments. For further information, contact Hilti Technical Support at 1-877-749-6337.
162 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Gauge Range2
Maximum Total
Thickness (MT), in.
Qty
20-28
20-28
18-26
18-26
0.072
0.072
0.100
0.100
1,000
10,000
1,000
4,500
Gauge Range2
Maximum Total
Thickness (MT), in.
Qty
20-28
20-28
20-28
20-28
20-28
20-28
20-28
20-28
20-28
20-28
0.072
0.072
0.072
0.072
0.072
0.072
0.072
0.072
0.072
0.072
20,000
15,000
13,000
10,000
5,000
4,000
9,000
9,000
6,000
3,000
Gauge Range2
Maximum Total
Thickness (MT), in.
Qty
16-22
14-20
14-20
14-20
14-20
14-20
14-20
0.125
0.175
0.175
0.175
0.175
0.175
0.175
1,000
7,500
6,500
6,500
5,000
4,000
4,000
Gauge Range2
Maximum Total
Thickness (MT), in.
Qty
12-20
12-20
12-20
12-20
12-20
0.210
0.210
0.210
0.210
0.210
3,000
2,500
2,000
2,000
1,500
Gauge Range2
Maximum Total
Thickness (MT), in.
Qty
14-20
0.175
TBD
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 163
Product Description
3.6.4.2
Material Specifications
3.6.4.3
Technical Data
3.6.4.4
Installation Instructions
3.6.4.5
Ordering Information
Product Features
Virtually immune to embrittlement
failure
Self-drilling for convenience,
labor savings
Kwik-Cote finish provides greater
corrosion resistance than cadmium
or zinc plating (reference Section
2.3.3.1)
Complies with the Buy America Act
Suitable for:
Aluminum to steel
Fire retardant plywood
Corrosive environments
(Reference Section 3.6.1.6)
Kwik-Flex Head:
Marking simplifies
inspection
Listings/Approvals
ICC-ES (International Code Council)
ESR-3332
COLA (City of Los Angeles)
RR 25095
Flutes remove
metal chips
for easy drilling
(634)
Yield Strength, Fu
ksi (MPa)
120
(828)
164 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Nominal
Diameter
in.
#10-16
0.190
#12-14
0.216
1/4-14
0.250
1/4-20
0.250
5/16-18
0.313
5/16-24
0.313
18
(0.048)
410
(1.82)
395
(1.76)
395
(1.76)
(3.16)
(4.09)
(3.96)
(4.09)
790
985
1530
1995
630
2745
(3.51)
(4.38)
(6.81)
(8.87)
(2.80)
(12.21)
765
1025
1685
2695
720
2905
(3.40)
(4.56)
(7.50)
(11.99)
(3.20)
(12.92)
780
1270
1570
2740
3130
3620
690
2100
4365
(3.47)
(5.65)
(6.98)
(12.19)
(13.92) (16.10)
(3.07)
(9.34)
(19.42)
1560
2120
(6.94)
(9.43)
1375
1910
2170
3565
4270
(6.12)
(8.50)
(9.65)
(15.86) (18.99)
16
(0.060)
580
(2.58)
615
(2.74)
620
(2.76)
610
(2.71)
1 The lower of the ultimate pullout, pullover, and tension fastener strength of screw should be used for design.
2 Load values based upon testing completed in accordance with AISI S905.
3 AISI S100 recommends a safety factor of 3.0 be applied for allowable strength design, a factor of 0.5 be applied for LRFD design and a factor of 0.4 be
applied for LSD design.
4 ANSI/ASME standard screw diameters were used in the calculations and are listed in the tables.
5 The screw diameters in the table above are available in head styles of pan, hex washer head, pancake, flat, wafer and bugle.
6 The load data in the table is based upon sheet steel with Fu = 45 ksi. For Fu = 55 ksi steel, multiply values by 1.22. For Fu = 65 ksi steel, multiply values by 1.44.
7 Load values based upon testing in 6063-T5 aluminum alloy.
8 Refer to Section 3.6.4.5 to ensure drilling capacities.
Washer or
Head
Diameter
in.
#10-16
0.384
#12-14
#12-24
0.398
1/4-14
0.480
18
(0.048)3
16
(0.060)
1245
(5.54)
1290
(5.74)
1555
(6.92)
1445
(6.43)
16103
(7.16)
19453
(8.65)
19453
(8.65)
1/4-20
0.480
5/16-18
0.600
5/16-24
0.600
#10
0.357
1160
(5.16)
1445
(6.43)
(6.43)
(6.43)
(6.43)
3
2015
2200
2200
2200
(8.96)
(9.79)
(9.79)
(9.79)
24303
3380
3380
3380
(10.81)
(15.03)
(15.03)
(15.03)
24303
3380
3380
3380
(10.81)
(15.03)
(15.03)
(15.03)
3505
3505
(15.59)
(15.59)
3980
3980
3980
(17.70)
(17.70)
(17.70)
Phillips Pan Head (PPH)
1805
2530
3010
(8.03)
(11.25)
(13.39)
1/4
5/16
3380
(15.03)
3380
(15.03)
3980
(17.70)
3980
(17.70)
1 The lower of the ultimate pullout, pullover, and tension fastener strength of screw should be used for design.
2 Unless otherwise noted, load values based upon testing completed in accordance with AISI S905.
3 Load values for 18 gauge and noted 16 and 14 gauge steel are based upon calculations done in accordance with Section E4 of AISI S100. ANSI/ASME standard screw
head diameters were used in the calculations and are listed in the table.
4 AISI S100 recommends a safety factor of 3.0 be applied for allowable strength design, a factor of 0.5 be applied for LRFD design and a factor of 0.4 be applied for
LSD design.
5 Pancake Framing Head Undercut (PFHUC) and Phillips Wafer Head (PWH) styles are not covered by this table because they are not used for attachment of steel to steel.
6 The load data in the table is based upon sheet steel with Fu = 45 ksi. For Fu = 55 ksi steel, multiply values by 1.22.
7 Refer to Section 3.6.4.5 to ensure drilling capacities.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 165
Nominal
Diameter
in.
#10-16 #2
0.190
#10-16 #3
0.190
#12-14
0.216
1/4-14
0.250
1/4-20
0.250
5/16-18
0.313
5/16-24
0.313
Thickness of members, in contact with screw head - not in contact with screw head
Aluminum7, in.
Steel6, ga (in.) or in.
1/4 18 (0.048) - 18 (0.048) - 16 (0.060) - 14 (0.075) 1/8-3/16
3/16 1/4
1/8 1/8
1/8 1/4
12 (0.105)
18 (0.048)
14 (0.075)
16 (0.060) 14 (0.075)
865
865
1210
1760
(3.85)
(3.85)
(5.38)
(7.83)
1105
1185
1360
1760
(4.92)
(5.27)
(6.05)
(7.83)
1070
1720
1540
1490
1005
1425
(4.76)
(7.65)
(6.85)
(6.63)
(4.47)
(6.34)
1985
1130
1880
1560
1915
1215
1770
(8.83)
(5.03)
(8.36)
(6.94)
(8.52)
(5.40)
(7.87)
1160
1580
1600
2010
1785
1870
1660
1185
1770
(5.16)
(7.03)
(7.12)
(8.94)
(7.94)
(8.32)
(7.38)
(5.27)
(7.87)
1225
1865
1685
2675
(5.45)
(8.30)
(7.50)
(11.90)
4040
2955
2660
2220
3440
(17.97)
(13.14)
(11.83)
(9.88)
(15.30)
1 The lower of the ultimate shear bearing and shear fastener strength of screw should be used for design.
2 Load values based upon testing completed in accordance with AISI S905.
3 AISI S100 recommends a safety factor of 3.0 be applied for allowable strength design, a factor of 0.5 be applied for LRFD design and a factor of 0.4 be
applied for LSD design.
4 ANSI/ASME standard screw head diameters were used in the calculations and are listed in the tables.
5 Load values in table are for Hex Washer Head (HWH) and Phillips Pan Head (PPH). Pancake Framing Head Undercut (PFHUC) and Phillips Wafer Head (PWH)
styles are not covered by this table because they are not used for attachment of steel to steel or aluminum to aluminum.
6 The load data in the table is based upon sheet steel with Fu = 45 ksi. For Fu = 55 ksi steel, multiply values by 1.22. For Fu = 65 ksi steel, multiply values by 1.44.
7 Load values based upon testing in 6063-T5 aluminum alloy.
8 Refer to Section 3.6.4.5 to ensure drilling capacities.
Nominal
Diameter
in.
0.190
0.216
0.216
0.250
0.250
0.313
0.313
1 The lower of the ultimate pullout, pullover, and tension fastener strength of
screw should be used for design. The Pullout and Pullover tables in this section
have already been adjusted where screw strength governs.
2 The lower of the ultimate shear fastener strength and shear bearing should
be used for design. The Shear Bearing table in this section has already been
adjusted where screw strength governs.
3 AISI S100 recommends a safety factor of 3.0 be applied for allowable strength
design, a factor of 0.5 be applied for LRFD design and a factor of 0.4 be
applied for LSD design.
4 When the distance to the end of the connected part is parallel to the line of the
applied force the allowable shear fastener strength must be reduced for end
distance, when necessary, in accordance with E4.3.2 of Appendix A of
AISI S100.
166 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
For general discussion of Hilti screw fastener installation, reference Section 3.6.1.7. For specific Kwik-Flex spacing and edge
distance recommendations, reference the following table.
Kwik-Flex Screw Specification Table
Fastener
Size/Diameter
#10
#12
1/4 Inch
Fastened
Material
Steel
Aluminum
Steel
Aluminum
Steel
Aluminum
Minimum
Spacing (in.)
5/8
15/32
11/16
9/16
3/4
5/8
Minimum Edge
Distance (in.)
9/32
3/8
3/8
7/16
3/8
1/2
Maximum Total
Thcikness (MT)
Recess
Box Qty
Countersinking Head
S-WD 10-24 x 1 1/4" PWH3 KF
S-WD 12-14 x 1" PFHUC3 KF
S-WD 12-14 x 1 1/2" PFHUC3 KF1
S-WD 14-20 x 3" PFHUC4 KF1
S-WD 14-20 x 4" PFHUC4 KF1
0.175"
0.210"
0.210"
0.312"
0.312"
0.750"
0.500"
1.000"
2.500"
3.500"
PH2 TEK
PH2 TEK
PH2 TEK
PH3
PH3
5,000
4,000
2,500
500
500
#10 Diameter
S-MD 10-16 x 3/4" PPH3 KF1
S-MD 10-16 x 3/4" HWH3 KF
0.175"
0.175"
0.500"
0.500"
PH2 TEK
5/16"
6,000
6,000
0.210"
0.210"
0.210"
0.312"
0.210"
0.210"
0.500"
0.470"
0.500"
1.000"
0.875"
1.500"
2.500"
0.800"
5/16"
5/16"
5/16"
5/16"
5/16"
5/16"
5/16"
5,000
4,000
2,500
2,500
2,000
1,000
2,500
0.220"
0.220"
0.220"
0.312"
0.312"
0.500"
0.312"
0.312"
0.312"
0.312"
0.450"
0.950"
1.450"
0.500"
0.830"
0.800"
1.330"
1.830"
2.700"
3.500"
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
3,000
2,000
1,500
2,500
2,000
1,000
1,500
1,000
500
500
0.220"
0.312"
0.312"
0.850"
0.850"
1.350"
3/8"
3/8"
3/8"
1,000
1,000
1,000
Description1
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 167
Product Description
3.6.5.2
Material Specifications
3.6.5.3
Technical Data
3.6.5.4
Installation Instructions
3.6.5.5
Ordering Information
Silvercolored
Kwik-Cote
coating
over entire
fastener
Self-drilling
point
300 series
stainless
steel head
and shank
Fused and
hardened
carbon steel
tapping
threads and
drill point
Listings/Approvals
COLA (City of Los Angeles)
RR 25886
Self-Drilling Fasteners
Made of 302/304 series (18/8) stainless
steel alloy to provide unmatched
corrosion resistance in your toughest
applications
Fused and hardened carbon steel drill
point and lead threads quickly drill
and tap structural steel and aluminum
up 1/2" thick
Coated with silver-colored KwikCote, a galvanic barrier to help
protect aluminum components
from accelerated corrosion when in
contact with 300 series stainless steel
300 series stainless alloy is virtually
immune to delayed embrittlement
failures seen with hardened 400
series stainless self-drilling fasteners
300 series stainless alloy is virtually
immune to Hydrogen-Assisted
Stress-Corrosion Cracking (HASCC).
Hardened 410 stainless steel, 410
super-passivated stainless steel and
400 modified stainless steel self-drilling
screws are generally considered
susceptible to HASCC. Conventional
hardened carbon steel screws with
coatings that do not have Kwik-Flex
technology (differential hardness) are
also generally considered susceptible
to HASCC.
Fastener
Material1
Stainless Steel
Self-Drilling
Point Material
Carbon Steel
Fastener
Plating
Kwik-Cote
1 Bi-Metal Kwik-Flex Fasteners with HWH style are SAE 304 stainless steel, while the PFH and PFHUC
style fasteners are SAE 302 stainless steel. All head styles can be custom ordered in SAE 316
stainless steel with sufficient lead time and quantities.
168 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Size
Length (L)
10-16
3/4"
1"
1-1/2"
2-1/2"
2"
1"
1-1/2"
2"
2-1/2"
3"
4"
2"
Drive
Recess
Drill
Point Size
Maximum Drilling
Capacity (DC)
Maximum Total
Thickness1 (MT)
0.110"
0.210"
0.500"
0.312"
0.500"
0.320"
0.500"
1.00"
2.00"
1.100"
0.500"
1.00"
1.500"
2.00"
2.50"
3.50"
1.100"
#2
phillips
0.140"
0.800"
#3
phillips
0.500"
12-14
12-24
1/4-20
5/16"
hex
3/8"
hex
10-16
1-1/2"
12-24
2-13/16"
1/4-20
2-13/16"
1.710"
1.710"
1"
0.500"
12-14
S-WD 12-14 x 1-1/2" PFHUC #3 BM Kwik-Flex
0.140"
1-1/2"
1.00"
#3
phillips
3"
2.500"
1/4-20
S-WD 1/4 - 20 x4" PFHUC #2 BM Kwik-Flex
0.210"
4"
3.500"
1 Maximum total thickness (MT) describes the maximum thickness of all attachments plus the base material thickness and is the load-bearing length of 300
series stainless under the hex head or including the flat head. Hardened carbon steel length (lead threads and point) should be completely through the base
material and not in the load bearing section of the connection.
Pullout (lb)
Aluminum 6063-T5
22 ksi
Size
Tensile
(lb)
Shear
(lb)
Drill
Screw Point
Size
Type
Drill
Cap
(in.)
10-16
1847
1282
18 ga.
16 ga.
14 ga.
12 ga.
1/8"
3/16"
1/4"
1/8"
1/4"
12-14
2628
1950
10-16
10-16
2
3
0.150
0.187
455
677
616
793
684
1394
1242
1906
1605
1527
994
961
12-24
2734
2284
1/4-20
4124
2860
12-14
0.187
528
750
892
1536
2602
2514
1132
12-14
12-24
1/4-20
1/4-20
3
5
3
5
0.210
0.500
0.312
0.500
417
679
680
802
780
1371
1442
2028
2623
2499
2110
3684
2781
4069
2622
974
538
1037
1995
2786
1724
1 All performance data shown is based on tests performed under laboratory conditions at independent construction testing facilities. The appropriate safety
factor should be applied and code requirements factored into specification and use of these fasteners. A safety factor of 4:1 or 25% of the ultimate average
values shown is generally accepted as an appropriate allowable load. Final determination of the appropriate safety factor and use of these fasteners is the
sole responsibility of the person designing the connection. For additional product information and technical assistance, please contact Hilti directly at
1-877-749-6337.
2 Values are for 300 series stainless fastener threaded shank.
3 The lower of the ultimate pullout and tensile fastener strength of screw should be used for design. Pullover or shear bearing capacity of the material being
fastened must be independently evaluated.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 169
flat head
Description
Maximum Total
Thickness (MT)
Drive Recess
Box Qty
0.800"
PH2 TEK
3,500
1.710"
PH3
1,500
1.710"
PH3
1,000
0.500"
1.000"
PH3
PH3
4,000
2,500
0.210"
2.500"
PH3
500
0.210"
#10 Diameter HWH
0.110"
#12 Diameter HWH
0.210"
3.500"
PH3
500
0.320"
5/16"
5,000
0.500"
5/16"
4,000
0.210"
1.000"
5/16"
2,500
0.210"
2.000"
5/16"
1,000
0.500"
1.100"
5/16"
2,000
0.500"
3/8"
2,500
0.312"
1.000"
3/8"
1,000
0.312"
1.500"
3/8"
1,000
0.500"
1.100"
3/8"
1,500
0.312"
2.000"
3/8"
1,000
0.312"
2.500"
3/8"
500
0.312"
3.500"
3/8"
500
0.500"
0.500"
Countersinking Head
0.140"
0.140"
170 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Reference
4.1.2 COLA
(City of Los Angeles)
Approvals
Report No.
25296
25646
25651
25662
25675
25678
Title
ESR-1663
ESR-1752
ESR-2184
ESR-2196
ESR-2197
ESR-2269
25684
ESR-2347
25708
ESR-2379
25826
ESR-2776
25839
25877
Hilti X-EDNK22 THQ12, X-EDN19 THQ12 or X-ENP19 L15 Power-Driven Fasteners and Hilti S-SLC01
MHWH and S-SLC02 MHWH Sidelap Connectors
25921
25095
25886
ESR-2795
ESR-2892
ESR- 3059
ESR-3332
4.1.3 UL/cUL
(Underwriters
Laboratories) Listings
4.1.4 FMRC
(Factory Mutual)
Approvals
File No.
Application / Product
EX2258
Pipe Hangers
Powder Actuated Fasteners
EW10-30-15P10, W10-30-32P10 and
W10-30-42P10
3036326
R13203
3029102
E217969
E201485
3011115
E257069
3026695
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 171
Reference
Standard
Title
B695
Standard
Title
C33
AC10
C36
AC43
C90
AC70
C150
AC118
C270
AC230
C330
C332
C476
C635
C636
AC368
Title
A36
A153
C954
A449
C1002
C1396
C1513
D1761
E380
E455
E1190
E2126
F594
F844
F1941
A493
A510
A572
A641
A653
A992
A1003
A1008
Standard Specification for Steel, Sheet, ColdRolled, Carbon, Structural, High-Strength LowAlloy, High-Strength Low-Alloy with Improved
Formability, Solution Hardened and Bake
Hardenable.
B117
B633
172 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Reference
Title
G15
Standard
Title
G85
UL 203
G87
UL 467
UL 580
UL 2239
UL 1565
Positioning Devices
Title
S100
S213
Standard
Title
S904
US-DOC
US DOC
S905
S907
Title
A10.3
B1.1
B1.13M
B18.12
B18.22
Plain Washers
Title
SAE J78
SAE J405
SAE J429
Title
ISO 3768
Metallic and Other Non-Organic Coatings Sulfur Dioxide Test with General
Condensation of Moisture
Title
DIN 50021
Title
IEC60947-7-2
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 173
Reference
Length
inch (in.)
foot (ft)
millimeter (mm)
meter (m)
Area
square inch (in2)
square inch (in2)
square foot (ft2)
Volume
cubic inch (in3)
cubic foot (ft3)
gallon (US gal)
Force
pound force (lbf)
pound force (lbf)
newton (N)
kilonewton (kN)
4.4482
0.0044
Multiply By
0.0069
newton/square millimeter
(N/mm2)
mega pascal (MPa)
6
8
10
12
16
20
25
32
Into
Length
millimeter (mm)
meter (m)
inch (in.)
foot (ft)
645.1600
6.4516
0.0929
Area
square millimeter (mm2)
square centimeter (cm2)
square meter (m2)
0.0016
0.1550
10.7639
16.3871
0.0283
3.7854
Volume
cubic centimeter (cm3)
cubic meter (m3)
liter (L)
0.0610
35.3147
0.2642
Force
newton (N)
kilonewton (kN)
0.2248
224.8089
145.0400
0.0069
newton/square
millimeter (N/mm2)
mega pascal (MPa)
145.0400
6.8946
0.1450
0.0209
25.4000
0.3048
Multiply By
0.0394
3.2808
Pressure
newton/square meter
(N/m2)
47.8801
1.3558
0.1130
newton/square meter
(N/m2)
0.7376
8.8496
Diaphragm Shear
pounds/foot (plf)
6.35
7.94
9.52
12.70
15.88
19.05
25.40
31.75
To Convert
Pressure
1/4
5/16
3/8
1/2
5/8
3/4
1
1-1/4
Hard Metric
Conversion
mm
To Convert
Inch-Pound System
In.
newton/meter (N/m)
14.5939
newton/meter (N/m)
0.0685
174 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013
Reference
Net 30 days from date of invoice. Customer agrees to pay all costs incurred by Hilti in collecting any
delinquent amounts, including attorneys fees.
Freight:
All sales are F.O.B. Destination with transportation allowed via Hilti designated mode. Delivery dates are
estimates only. Additional charges for expedited shipments, special handling requirements, and orders
below certain dollar amounts shall be the responsibility of Customer. Fuel surcharges may apply depending
on market conditions.
Credit:
Return Policy:
Products must be in saleable condition to qualify for return. Saleable condition is defined as unused items
in original undamaged packaging and unbroken quantities and in as-new condition. All returns are subject
to Hilti inspection and acceptance, and a $125 restocking charge if returned more than 90 days after
invoice date. Proof of purchase is required for all returned materials.
Ineligible Return:
Special order products and discontinued items are not eligible for return or credit. Dated materials
are only returnable in case quantity and within 14 days after invoice date. In no event shall any
product be returnable or qualify for credit after 1 year from invoice date.
Warranty:
Hilti warrants that for a period of 12 months from the date it sells a product it will, at its sole option and
discretion, refund the purchase price, repair, or replace such product if it contains a defect in material or
workmanship. Absence of Hiltis receipt of notification of any such defect within this 12-month period shall
constitute a waiver of all claims with regard to such product.
THE FOREGOING WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. Hilti shall in no event be liable for, and Customer hereby agrees
to indemnify Hilti against, all claims related to special, direct, indirect, incidental, consequential, and any
other damages arising out of or related to the sale, use, or inability to use the product, including costs and
attorneys fees.
Order
Acceptance:
Domestic Origin:
Acceptance is limited to the express terms contained herein, and terms are subject to change by Hilti
without notice. Additional or different terms proposed by Customer are deemed material and are objected
to and rejected, but such rejection shall not operate as a rejection of the offer unless it contains variances
in the terms of the description, quantity, price or delivery schedule of the goods. Orders are not deemed
accepted by Hilti unless and until it ships the associated items.
Origin information may be obtained by written request to Hilti, Inc., Contract Compliance, P. O. Box 21148,
Tulsa, Oklahoma 74121. Hiltis Quality Department personnel are the only individuals authorized to warrant
the country of origin of Hilti products.
Business Size:
Prices:
Prices are those stated on the order, and unless otherwise noted are based on purchasing all items on the
order pricing for individual products may vary for purchases of different quantities or item combinations.
Hilti does not maintain most favored customer records, makes no representation with respect to same, and
rejects any price warranty terms proposed by Customer. Hilti's published net price list is subject to change
without notice.
Consent to
Jurisdiction:
All transactions made pursuant hereto shall be deemed to have been made and entered into in Tulsa,
Oklahoma. Any and all disputes arising directly or indirectly from such transactions shall be resolved in
the courts of the County of Tulsa, State of Oklahoma, to the exclusion of any other court, and any resulting
judgment may be enforced by any court having jurisdiction of such an action. All transactions shall be
governed by and construed in accordance with the laws of the State of Oklahoma.
Indemnification:
Customer hereby agrees to indemnify Hilti for any costs, including attorneys fees, incurred by Hilti as a
result, in whole or in part, of any violation by Customer of any Federal, State or Local statute or regulation,
or of any nationally accepted standard. It shall be Customers sole responsibility to comply with all
applicable laws and regulations regarding the handling, use, transportation, or disposal of products upon
taking possession of same.
Convert Check to
Eft:
When you provide a check as payment, you authorize Hilti to use information from your check to make
a one time electronic fund transfer from your checking account or to process the payment as a check
transaction. When we use information from your check to make an electronic fund transfer, funds may be
withdrawn from your account as soon as the same day we receive your payment, and you will not receive
your check back from your financial institution.
Authorization:
HILTI LEGAL DEPARTMENT PERSONNEL ARE THE ONLY INDIVIDUALS AUTHORIZED TO MODIFY THESE
TERMS AND CONDITIONS, WARRANT PRODUCT SUITABILITY FOR SPECIFIC APPLICATIONS, ACCEPT
INFORMATION ON THE POTENTIAL FOR CONSEQUENTIAL DAMAGES, OR EXECUTE CUSTOMER
DOCUMENTS, AND ANY SUCH ACTION IS NULL AND VOID UNLESS IN WRITTEN FORM SIGNED BY
SUCH INDIVIDUAL. HILTI SALES REPRESENTATIVES (INCLUDING ACCOUNT MANAGERS, REGIONAL
MANAGERS, AND CUSTOMER SERVICE REPRESENTATIVES) HAVE NO SUCH AUTHORITY.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013 175
Reference
Payment Terms:
Net 30 days from date of invoice. Customer agrees to pay all costs incurred by Hilti in collecting any
delinquent amounts, if any, including reasonable attorneys fees.
Freight:
Sales are F.O.B. Destination Point with transportation allowed via Hilti designated mode. Additional charges
may apply for expedited delivery, special handling requirements, and orders under certain dollar limits. Fuel
surcharges may apply depending on market conditions.
Credit:
All orders sold on credit are subject to Credit Department approval, and Customer agreement to these
Terms and Conditions of Sale.
Return Policy:
Products must be in saleable condition to qualify for return. Saleable condition is defined as unused items
in original undamaged packaging and unbroken quantities and in as-new condition. All returns are subject
to Hilti inspection and acceptance, and a $150 restocking charge if returned more than 90 days after invoice
date. Proof of purchase is required for all returned materials.
Ineligible Returns:
Special order products and discontinued items are not eligible for return or credit. Dated materials are
only returnable in case quantity and within 14 days after invoice date. In no event shall any product be
returnable or qualify for credit after 1 year from invoice date.
Warranty:
Hilti warrants that for a period of 12 months from the date it sells a product it will, at its sole option and
discretion, refund the purchase price, repair, or replace such product if it contains a defect in material or
workmanship. Absence of Hiltis receipt of notification of any such defect within this 12-month period shall
constitute a waiver of all claims with regard to such product.
THE FOREGOING WARRANTY IS IN LIEU OF AND CUSTOMER WAIVES ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND THE SALE OF GOODS ACT AND
ANY SIMILAR STATUTE OF ANY PROVINCE.
Title to Product:
Title to product remains with Hilti until the total invoiced price of product is paid.
Prices:
Customer agrees to Pay Hilti the prices set out on Hiltis invoice. Customer agrees to pay taxes as
indicated on the invoice unless Customer provides acceptable exemption certificates.
Indemnification:
Customer agrees to use product at its own risk and to indemnify Hilti against all liabilities, including legal
fees, to third parties arising out of the use, inability to use, or possession thereof. Hilti shall in no event be
liable for special, incidental, consequential, or any other damages, regardless of fault.
Changes:
Only Hilti legal department personnel are authorized to modify these Terms and Conditions of Sale or
modify credit terms. Terms are subject to change by Hilti without notice.
Cash Sales:
Quotations:
These Terms and Conditions of Sale apply once Customer agrees to purchase product. Quotations
on special promotion products are only valid until end of promotion period. Quotations are based on
purchasing all items listed pricing for individual products may vary for purchases of different quantities
or item combinations.
Convert check to
When Customer provides a check as payment, it authorizes Hilti to use information from its check to make a
one-time electronic fund transfer from Customers checking account or to process the payment as a check
transaction. When Hilti uses information from the check to make an electronic fund transfer, funds may be
withdrawn from Customers account as soon as the same day Hilti receives the check and Customer will
not receive its check back from the financial institution.
ETF:
176 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Direct Fastening Technical Guide 2013