Professional Documents
Culture Documents
Copyright
Copyright 1984-2011 Intergraph Corporation. All Rights Reserved.
Including software, file formats, and audiovisual displays; may be used pursuant to applicable software license agreement;
contains confidential and proprietary information of Intergraph and/or third parties which is protected by copyright law, trade secret
law, and international treaty, and may not be provided or otherwise made available without proper authorization from Intergraph
Corporation.
Terms of Use
Use of this software product is subject to the End User License Agreement ("EULA") delivered with this software product unless the
licensee has a valid signed license for this software product with Intergraph Corporation. If the licensee has a valid signed license
for this software product with Intergraph Corporation, the valid signed license shall take precedence and govern the use of this
software product. Subject to the terms contained within the applicable license agreement, Intergraph Corporation gives licensee
permission to print a reasonable number of copies of the documentation as defined in the applicable license agreement and
delivered with the software product for licensee's internal, non-commercial use. The documentation may not be printed for resale or
redistribution.
Trademarks
Intergraph, the Intergraph logo, PDS, SmartPlant, FrameWorks, I-Convert, I-Export, I-Sketch, SmartMarine, IntelliShip, INtools,
ISOGEN, MARIAN, SmartSketch, SPOOLGEN, SupportManager, and SupportModeler are trademarks or registered trademarks of
Intergraph Corporation or its subsidiaries in the United States and other countries. Microsoft and Windows are registered
trademarks of Microsoft Corporation. Oracle, JD Edwards, PeopleSoft, and Retek are registered trademarks of Oracle Corporation
and/or its affiliates. MicroStation is a registered trademark of Bentley Systems Inc, all rights reserved. Other brands and product
names are trademarks of their respective owners.
Contents
Preface PDS ............................................................................................................................................... 15
Introduction ................................................................................................................................................ 17
Reference Data File Descriptions ......................................................................................................... 17
Piping Job Specification File Descriptions...................................................................................... 17
Non-Database Part of the Piping Job Specification ....................................................................... 18
Non-Database Part of Item Descriptions ........................................................................................ 19
Model Graphics .............................................................................................................................. 19
Design DDL .................................................................................................................................... 20
Seed File Definitions....................................................................................................................... 20
General Conventions ................................................................................................................................ 23
Variables Used in Symbols and Tables ................................................................................................ 32
Definition of Specific Variables ....................................................................................................... 32
Definition of Generic Variables ....................................................................................................... 35
Commodity Discussions ........................................................................................................................... 39
Piping Commodity Data ........................................................................................................................ 39
Basic Information ............................................................................................................................ 39
Non-parametric and Parametric Piping and Tubing (PIPING, TUBING) ........................................ 40
Valves (6Q1C) ................................................................................................................................ 43
On-line Fittings (6P2C) and In-line Fittings (6Q2C) .............................................................................. 74
Connect Point Data_GCP .............................................................................................................. 75
6Q2C01, Flange (in-line) ................................................................................................................ 80
6Q2C03, Reducing flange (in-line) (not-automatic) ........................................................................ 83
6Q2C04, Expander flange (in-line) (not-automatic) ....................................................................... 84
6Q2C06, Orifice flange (in-line) (not-automatic) ............................................................................ 84
6Q2C08, Blind flange (in-line) (not-automatic) ............................................................................... 86
6Q2C10, Open spectacle blank (in-line) (not-automatic) ............................................................... 87
6Q2C11, Closed spectacle blank (in-line) (not-automatic)............................................................. 87
6Q2C12, Blank disc (in-line) (not-automatic) ................................................................................. 87
6Q2C13, Blind spacer (in-line) (not-automatic) .............................................................................. 87
6Q2C14, Tapered spacer (in-line) (not-automatic) ........................................................................ 87
6Q2C15, Open spacer (in-line) (not-automatic) ............................................................................. 88
6Q2C16, End (in-line) (not-automatic) ........................................................................................... 88
6Q2C17, Head (in-line) (not-automatic) ......................................................................................... 88
6Q2C19, Plug (in-line) (not-automatic)........................................................................................... 89
6Q2C21, Cap (in-line) (not-automatic) ........................................................................................... 89
6Q2C23, Concentric diameter change (in-line) .............................................................................. 89
6Q2C24, Eccentric diameter change (in-line) (not-automatic) ....................................................... 89
6Q2C25, Coupling-connector (in-line) (not-automatic) .................................................................. 89
6Q2C26, Half coupling (in-line) (not-automatic) ............................................................................. 90
6Q2C27, Concentric reducer (in-line)............................................................................................. 91
6Q2C28, Eccentric reducer (in-line) (not-automatic) ...................................................................... 92
6Q2C32, Reducing coupling (in-line) (not-automatic) .................................................................... 92
6Q2C35, Concentric swage (in-line) .............................................................................................. 93
6Q2C36, Eccentric swage (in-line) (not-automatic) ....................................................................... 93
Contents
6Q2C39, Union (in-line) (not-automatic) ........................................................................................ 94
6Q2C40, Orifice union (in-line) (not-automatic) ............................................................................. 94
6Q2C41, Dielectric union (in-line) (not-automatic) ......................................................................... 94
6Q2C43, Hose connection (in-line) (not-automatic) ....................................................................... 94
6Q2C44, Bushing (in-line) (not-automatic) ..................................................................................... 95
6Q2C46, Reducing insert (in-line) (not-automatic) ......................................................................... 95
6Q2C47, Pipe bend (in-line) ........................................................................................................... 95
6Q2C49, 5.625 deg elbow (in-line) (not-automatic) ....................................................................... 96
6Q2C51, 11.25 deg elbow (in-line) (not-automatic) ....................................................................... 96
6Q2C53, 22.5 deg elbow (in-line) (not-automatic) ......................................................................... 97
6Q2C55, <45 deg direction change (in-line) .................................................................................. 97
6Q2C56, 45 deg direction change (in-line) .................................................................................... 98
6Q2C57, 45 deg elbow (in-line) ...................................................................................................... 98
6Q2C59, 45 deg LR elbow (in-line) ................................................................................................ 99
6Q2C60, 45 deg long tangent elbow (in-line) ................................................................................. 99
6Q2C61, 45 deg 3D elbow (in-line) .............................................................................................. 100
6Q2C63, 45 deg union elbow (in-line) (not-automatic) ................................................................ 100
6Q2C65, 45 deg street elbow (in-line) (not-automatic) ................................................................ 100
6Q2C66, 45 deg short elbow (in-line)........................................................................................... 101
6Q2C68, 45 deg long elbow (in-line) ............................................................................................ 101
6Q2C73, 60 deg elbow (in-line) (not-automatic) .......................................................................... 101
6Q2C75, 45-90 deg direction change (in-line) ............................................................................. 101
6Q2C76, 90 deg direction change (in-line) .................................................................................. 102
6Q2C77, 90 deg elbow (in-line) .................................................................................................... 102
6Q2C79, 90 deg SR elbow (in-line).............................................................................................. 103
6Q2C80, 90 deg LR elbow (in-line) .............................................................................................. 103
6Q2C82, 90 deg LR long tangent elbow (in-line) ......................................................................... 104
6Q2C84, 90 deg reducing elbow (in-line) ..................................................................................... 104
6Q2C86, 90 deg 3D elbow (in-line) .............................................................................................. 104
6Q2C88, 90 deg union elbow (in-line) (not-automatic) ................................................................ 105
6Q2C90, 90 deg street elbow (in-line) (not-automatic) ................................................................ 105
6Q2C91, 90 deg reducing street elbow (in-line) (not-automatic) ................................................. 105
6Q2C93, 90 deg short elbow (in-line)........................................................................................... 106
6Q2C94, 90 deg long elbow (in-line) ............................................................................................ 106
On-line Fittings (6P3C) and In-line Fittings (6Q3C) ............................................................................ 106
Connect Point Data_Independent Variables ................................................................................ 107
6Q3C01, 180 deg return (in-line) (not-automatic) ........................................................................ 112
6Q3C03, 180 deg SR return (in-line) (not-automatic) .................................................................. 112
6Q3C05, 180 deg LR return (in-line) (not-automatic) ................................................................... 112
6Q3C07, 180 deg close return (in-line) (not-automatic) ............................................................... 112
6Q3C08, 180 deg medium return (in-line) (not-automatic) .......................................................... 113
6Q3C09, 180 deg open return (in-line) (not-automatic) ............................................................... 113
6Q3C14, Miter (in-line) (not-automatic) ........................................................................................ 113
6Q3C16, 45 deg miter (in-line) ..................................................................................................... 114
6Q3C18, 90 deg miter (in-line) ..................................................................................................... 115
6Q3C22, Tee (in-line) ................................................................................................................... 116
6Q3C24, Reducing branch tee (in-line) ........................................................................................ 117
6Q3C25, Reducing run and branch tee (in-line) .......................................................................... 119
6Q3C27, On-run union tee (in-line) (not-automatic) ..................................................................... 119
6Q3C28, On-branch union tee (in-line) (not-automatic) ............................................................... 119
6Q3C31, Street tee (in-line) (not-automatic) ................................................................................ 120
6Q3C34, Reducing instrument tee (in-line) (not-automatic)......................................................... 120
6Q3C36, Drip ring tee (in-line) (not-automatic) ............................................................................ 120
Contents
6Q3C38, Basin tee (in-line) .......................................................................................................... 121
6Q3C45, True Y (in-line) (not-automatic) ..................................................................................... 121
6Q3C47, Lateral (in-line) .............................................................................................................. 121
6Q3C49, Reducing branch lateral (in-line) ................................................................................... 122
6Q3C50, Reducing run and branch lateral (in-line) ...................................................................... 123
6Q3C52, 90 deg short Y-branch (in-line) (not-automatic) ............................................................ 123
6Q3C53, 90 deg reducing short Y-branch (in-line) (not-automatic) ............................................. 123
6Q3C54, 90 deg long Y-branch (in-line) (not-automatic) ............................................................. 123
6Q3C55, 90 deg reducing long Y-branch (in-line) (not-automatic) .............................................. 124
6Q3C60, Cross (in-line) (not-automatic) ...................................................................................... 124
6Q3C62, Reducing branches cross (in-line) (not-automatic) ....................................................... 125
6Q3C63, Reducing run and branches cross (in-line) (not-automatic) .......................................... 125
6Q3C64, Basin cross (in-line) (not-automatic) ............................................................................. 126
6Q3C70, Saddle (in-line) .............................................................................................................. 126
6Q3C72, Sweepolet (in-line) ........................................................................................................ 126
6Q3C73, Weldolet (in-line) ........................................................................................................... 127
6Q3C74, Sockolet (in-line) ........................................................................................................... 127
6Q3C75, Thredolet (in-line) .......................................................................................................... 128
6Q3C76, Nippolet (in-line) ............................................................................................................ 128
6Q3C77, Elbolet (in-line) (not-automatic) ..................................................................................... 129
6Q3C78, Latrolet (in-line) (not-automatic) .................................................................................... 129
6Q3C79, Endolet (in-line) (not-automatic).................................................................................... 130
6Q3C80, Reinforcing pad (in-line) ................................................................................................ 130
6Q3C82, Reinforcing weld (in-line) .............................................................................................. 132
6Q3C84, Buttweld (in-line) (not-automatic) .................................................................................. 134
6Q3C86, Full Encirclement Reinforcement Pad (In-Line) ............................................................ 134
6Q3C88, Branch nipple (in-line) (not-automatic) .......................................................................... 134
6Q3C89, In-line nipple (in-line) (not-automatic) ........................................................................... 135
6Q3C95, Gasket ........................................................................................................................... 135
6Q3C97, Stud ............................................................................................................................... 137
Fire and Safety Piping Components, On-line (6P4C), In-line (6Q4C) ................................................ 140
Connect Point Data ...................................................................................................................... 141
6Q4C01, Fire monitor (in-line) ...................................................................................................... 145
6Q4C02, Elevated fire monitor (in-line) ........................................................................................ 145
6Q4C03, Remotely operated fire monitor (in-line) ....................................................................... 145
6Q4C04, Foam monitor (in-line) ................................................................................................... 146
6Q4C05 Elevated foam monitor (in-line) ...................................................................................... 146
6Q4C06, Remotely operated foam monitor (in-line) .................................................................... 146
6Q4C10, [2-way] fire hydrant (in-line) .......................................................................................... 147
6Q4C11, [2-way] fire hydrant w/monitor nozzle (in-line) .............................................................. 147
6Q4C13, 3-way fire hydrant (in-line) ............................................................................................ 147
6Q4C24, Hose reel (in-line) .......................................................................................................... 148
6Q4C25, Hose rack station (in-line) ............................................................................................. 148
6Q4C26, Foam chamber (in-line) ................................................................................................. 148
6P4C30, Wet sprinkler (on-line) ................................................................................................... 148
6P4C31, Pre-action sprinkler (on-line) ......................................................................................... 149
6P4C32, Spray sprinkler (on-line) ................................................................................................ 149
6Q4C38, Eye wash (in-line) ......................................................................................................... 149
6Q4C39, Safety shower (in-line) .................................................................................................. 149
6Q4C40, Safety shower and eye wash (in-line) ........................................................................... 149
6Q4C60, [2-way] siamese (in-line) ............................................................................................... 150
6Q4C66, [2-way] 90 deg siamese (in-line) ................................................................................... 150
In-Line Bio-Pharmaceutical Components (6Q5P) ............................................................................... 150
Contents
Bio-Pharmaceutical Specification Components ........................................................................... 150
Bio-Pharmaceutical Operators ..................................................................................................... 160
Bio-Pharmaceutical Specialty Components ................................................................................. 161
Piping Specialty Components, On-line (6P6C) , In-line (6Q6C) ......................................................... 163
Named and Unamed Specialties .................................................................................................. 165
Connect Point Data ...................................................................................................................... 165
6Q6C01, Flame arrestor (in-line) (PID piping comp type 513)................................................... 168
6Q6C03, Hammer arrestor (in-line) (PID piping comp type 515) ............................................... 168
6Q6C04, Vent silencer (in-line) (PID piping comp type 516) ..................................................... 168
6Q6C05, In-line silencer (in-line) (PID piping comp type 517) ................................................... 168
6Q6C07, Exhaust head (in-line) (PID piping comp type 519) .................................................... 169
6Q6C09, Breather vent (in-line) (PID piping comp type 521) .................................................... 169
6Q6C11, Free vent w/o screen (in-line) (PID piping comp type 523) ........................................ 169
6Q6C12, Free vent w/screen (in-line) (PID piping comp type 524) ........................................... 169
6Q6C13, Motor operated valve (in-line) (with operator) ............................................................. 169
6Q6C15, Mixing T (in-line) (PID piping comp type 527) ............................................................ 169
6P6C17, Spray nozzle (on-line) (PID piping comp type 529) .................................................... 169
6Q6C21, Removable spool (in-line) (PID piping comp type 533) .............................................. 170
6Q6C23, Swing elbow (in-line) (PID piping comp type 535) ...................................................... 170
6Q6C28, Expansion joint (in-line) (PID piping comp type 540).................................................. 170
6Q6C30, Hinged expansion joint (in-line) (PID piping comp type 542) ..................................... 170
6Q6C32, Swivel joint (in-line) (PID piping comp type 544) ........................................................ 170
6Q6C34, Mechanical coupling (in-line) (PID piping comp type 546) ......................................... 171
6Q6C36, Flexible hose (in-line) (PID piping comp type 548) ..................................................... 171
6Q6C40, Sample cooler (in-line) (PID piping comp type 552) ................................................... 172
6Q6C45, Single basket strainer (in-line) (PID piping comp type 557) ....................................... 172
6Q6C47, Duplex basket strainer (in-line with operator) (PID piping comp type
559)............................................................................................................................................... 172
6Q6C49, T strainer (in-line) (PID piping comp type 561) ........................................................... 172
6Q6C51, Y strainer (in-line) (PID piping comp type 563) ........................................................... 173
6Q6C52, Temporary strainer (in-line) (PID piping comp type 564) ........................................... 173
6Q6C53, Basket strainer (in-line) (PID piping comp type 565) .................................................. 173
6Q6C55, Cone strainer (in-line) (PID piping comp type 567) .................................................... 174
6Q6C57, Flat plate strainer (in-line) (PID piping comp type 569) .............................................. 174
6Q6C59, Sump strainer (in-line) (PID piping comp type 571).................................................... 174
6Q6C64, Filter (in-line) (PID piping comp type 576) .................................................................. 174
6Q6C70, Steam trap (in-line) (PID piping comp type 582) ........................................................ 174
6Q6C71, Float steam trap (in-line) (PID piping comp type 583) ................................................ 174
6Q6C72, Inverted bucket steam trap (in-line) (PID piping comp type 584) ............................... 174
6Q6C74, Thermostatic steam trap (in-line) (PID piping comp type 586) ................................... 174
6Q6C76, Thermodynamic steam trap (in-line) (PID piping comp type 588) .............................. 174
6Q6C78, Impulse steam trap (in-line) (PID piping comp type 590) ........................................... 174
6Q6C99, Generic component (in-line) (PID piping comp type 611) .......................................... 175
Instrument Specialty Discussions ....................................................................................................... 175
Signal Lines (7N2A) ...................................................................................................................... 176
Control Valves and Regulators (7P1E) ........................................................................................ 176
Relief Devices (7P2C) .................................................................................................................. 186
Other in-line Instruments (7P3C) .................................................................................................. 191
Off-Line Instruments (7Q4D) ........................................................................................................ 201
Miscellaneous ..................................................................................................................................... 218
Valve Operators and Actuators .................................................................................................... 219
Piping Connectors ........................................................................................................................ 228
6Q3C83, Non-radial Reinforcing Weld ......................................................................................... 229
Contents
Assemblies .......................................................................................................................................... 230
In-line Piping Macrocomponents (6N8C) ..................................................................................... 230
On-line Piping Macrocomponents (6P8C) .................................................................................... 230
Symbols .................................................................................................................................................... 231
Piping Commodity Symbols ................................................................................................................ 231
Piping Commodity Symbol Legend .............................................................................................. 231
Piping Commodity Symbol P1 ...................................................................................................... 232
Piping Commodity Symbol V1 ...................................................................................................... 233
Piping Commodity Symbol V2 ...................................................................................................... 234
Piping Commodity Symbol V2A ................................................................................................... 235
Piping Commodity Symbol V2B ................................................................................................... 235
Piping Commodity Symbol V3 ...................................................................................................... 236
Piping Commodity Symbol V4 ...................................................................................................... 237
Piping Commodity Symbol V6 ...................................................................................................... 238
Piping Commodity Symbol V8 ...................................................................................................... 239
Piping Commodity Symbol V11 .................................................................................................... 240
Piping Commodity Symbol V12 .................................................................................................... 241
Piping Commodity Symbol V13 .................................................................................................... 242
Piping Commodity Symbol V16 .................................................................................................... 243
Piping Commodity Symbol V18 .................................................................................................... 244
Piping Commodity Symbol V19 .................................................................................................... 245
Piping Commodity Symbol V26 .................................................................................................... 246
Piping Commodity Symbol V32 .................................................................................................... 247
Piping Commodity Symbol V33 .................................................................................................... 248
Piping Commodity Symbol V34 .................................................................................................... 249
Piping Commodity Symbol V38 .................................................................................................... 250
Piping Commodity Symbol V40 .................................................................................................... 251
Piping Commodity Symbol V41 .................................................................................................... 252
Piping Commodity Symbol V42 .................................................................................................... 253
Piping Commodity Symbol V51 .................................................................................................... 254
Piping Commodity Symbol V58 .................................................................................................... 255
Piping Commodity Symbol V62 .................................................................................................... 256
Piping Commodity Symbol V72 .................................................................................................... 257
Piping Commodity Symbol V81 .................................................................................................... 258
Piping Commodity Symbol V82 .................................................................................................... 259
Piping Commodity Symbol F1A .................................................................................................... 260
Piping Commodity Symbol F4 ...................................................................................................... 261
Piping Commodity Symbol F6 ...................................................................................................... 262
Piping Commodity Symbol F8 ...................................................................................................... 263
Piping Commodity Symbol F10_1 ................................................................................................ 264
Piping Commodity Symbol F10_2 ................................................................................................ 265
Piping Commodity Symbol F13 .................................................................................................... 266
Piping Commodity Symbol F14A .................................................................................................. 267
Piping Commodity Symbol F14B .................................................................................................. 268
Piping Commodity Symbol F17D ................................................................................................. 269
Piping Commodity Symbol F19 .................................................................................................... 270
Piping Commodity Symbol F25 .................................................................................................... 271
Piping Commodity Symbol F27 .................................................................................................... 272
Piping Commodity Symbol F28 .................................................................................................... 273
Piping Commodity Symbol F31 .................................................................................................... 274
Piping Commodity Symbol F32 .................................................................................................... 275
Piping Commodity Symbol F39 .................................................................................................... 276
Contents
Piping Commodity Symbol F43_1 ................................................................................................ 277
Piping Commodity Symbol F43_2 ................................................................................................ 278
Piping Commodity Symbol F47 .................................................................................................... 279
Piping Commodity Symbol F47A .................................................................................................. 280
Piping Commodity Symbol F63 .................................................................................................... 281
Piping Commodity Symbol F84 .................................................................................................... 282
Piping Commodity Symbol F101 .................................................................................................. 283
Piping Commodity Symbol F114A ................................................................................................ 284
Piping Commodity Symbol F114B ................................................................................................ 285
Piping Commodity Symbol F114C ............................................................................................... 286
Piping Commodity Symbol F114D ............................................................................................... 287
Piping Commodity Symbol F122_1 .............................................................................................. 288
Piping Commodity Symbol F122_2 .............................................................................................. 289
Piping Commodity Symbol F125 .................................................................................................. 290
Piping Commodity Symbol F127 .................................................................................................. 291
Piping Commodity Symbol F128 .................................................................................................. 292
Piping Commodity Symbol F134 .................................................................................................. 293
Piping Commodity Symbol F145 .................................................................................................. 294
Piping Commodity Symbol F147 .................................................................................................. 295
Piping Commodity Symbol F150 .................................................................................................. 296
Piping Commodity Symbol F152 .................................................................................................. 297
Piping Commodity Symbol F154 .................................................................................................. 298
Piping Commodity Symbol F160 .................................................................................................. 299
Piping Commodity Symbol F163 .................................................................................................. 300
Piping Commodity Symbol F170 .................................................................................................. 301
Piping Commodity Symbol F172 .................................................................................................. 302
Piping Commodity Symbol F173 .................................................................................................. 303
Piping Commodity Symbol F176 .................................................................................................. 304
Piping Commodity Symbol F177 .................................................................................................. 305
Piping Commodity Symbol F180F ................................................................................................ 306
Piping Commodity Symbol F178 .................................................................................................. 307
Piping Commodity Symbol F179 .................................................................................................. 308
Piping Commodity Symbol F180 .................................................................................................. 309
Piping Commodity Symbol F182 .................................................................................................. 310
Piping Commodity Symbol F184 .................................................................................................. 311
Piping Commodity Symbol F188 .................................................................................................. 312
Fire and Safety Symbols ..................................................................................................................... 313
Fire and Safety Symbol FS1A ...................................................................................................... 313
Fire and Safety Symbol FS2B ...................................................................................................... 313
Fire and Safety Symbol FS10A .................................................................................................... 314
Fire and Safety Symbol FS10B .................................................................................................... 314
Fire and Safety Symbol FS11A .................................................................................................... 315
Fire and Safety Symbol FS11B .................................................................................................... 315
Fire and Safety Symbol FS13A .................................................................................................... 316
Fire and Safety Symbol FS13B .................................................................................................... 316
Fire and Safety Symbol FS24A .................................................................................................... 317
Fire and Safety Symbol FS26A .................................................................................................... 317
Fire and Safety Symbol FS26B .................................................................................................... 318
Fire and Safety Symbol FS30A .................................................................................................... 318
Fire and Safety Symbol FS38A .................................................................................................... 319
Fire and Safety Symbol FS39A .................................................................................................... 319
Fire and Safety Symbol FS60A .................................................................................................... 320
Fire and Safety Symbol FS66A338 .............................................................................................. 320
Contents
Fire and Safety Symbol T-FS1A ................................................................................................... 321
Fire and Safety Symbol T-FS2B ................................................................................................... 321
Fire and Safety Symbol T-FS10A ................................................................................................. 322
Fire and Safety Symbol T-FS11A ................................................................................................. 322
Fire and Safety Symbol T-FS13A ................................................................................................. 323
Piping Specialty Symbols .................................................................................................................... 323
Piping Specialty Symbol S1AC .................................................................................................... 323
Piping Specialty Symbol S1BZ ..................................................................................................... 324
Piping Specialty Symbol S3AZ ..................................................................................................... 324
Piping Specialty Symbol S4AC .................................................................................................... 325
Piping Specialty Symbol S5AZ ..................................................................................................... 325
Piping Specialty Symbol S7AZ ..................................................................................................... 326
Piping Specialty Symbol S11BZ ................................................................................................... 326
Piping Specialty Symbol S13AZ ................................................................................................... 327
Piping Specialty Symbol S28AZ ................................................................................................... 327
Piping Specialty Symbol S28BZ ................................................................................................... 328
Piping Specialty Symbol S32BC .................................................................................................. 328
Piping Specialty Symbol S36AZ ................................................................................................... 329
Piping Specialty Symbol S49AC .................................................................................................. 329
Piping Specialty Symbol S51AC .................................................................................................. 330
Piping Specialty Symbol S53AC .................................................................................................. 330
Piping Specialty Symbol S64BC .................................................................................................. 331
Piping Specialty Symbol S70AC .................................................................................................. 331
Piping Specialty Symbol S70BC .................................................................................................. 332
Piping Specialty Symbol S78AC .................................................................................................. 332
Instrument Specialty Symbols ............................................................................................................. 333
Instrument Specialty Symbol I3AZ ............................................................................................... 333
Instrument Specialty Symbol I5AZ ............................................................................................... 333
Instrument Specialty Symbol I6AZ ............................................................................................... 334
Instrument Specialty Symbol I7AZ ............................................................................................... 334
Instrument Specialty Symbol I8AZ ............................................................................................... 335
Instrument Specialty Symbol I11AZ ............................................................................................. 335
Instrument Specialty Symbol I12AZ ............................................................................................. 336
Instrument Specialty Symbol I13AZ ............................................................................................. 336
Instrument Specialty Symbol I14AZ ............................................................................................. 337
Instrument Specialty Symbol I15AZ ............................................................................................. 337
Instrument Specialty Symbol I16AZ ............................................................................................. 338
Instrument Specialty Symbol I17AZ ............................................................................................. 338
Instrument Specialty Symbol I18AZ ............................................................................................. 339
Instrument Specialty Symbol I20AZ ............................................................................................. 339
Instrument Specialty Symbol I30AZ ............................................................................................. 340
Instrument Specialty Symbol I106BZ ........................................................................................... 340
Instrument Specialty Symbol I109BZ ........................................................................................... 341
Instrument Specialty Symbol I118BZ ........................................................................................... 341
Instrument Specialty Symbol I120AZ ........................................................................................... 342
Instrument Specialty Symbol I201AZ ........................................................................................... 342
Instrument Specialty Symbol I201BZ ........................................................................................... 343
Instrument Specialty Symbol I201CZ ........................................................................................... 343
Instrument Specialty Symbol I209AZ ........................................................................................... 344
Instrument Specialty Symbol I213AZ ........................................................................................... 344
Instrument Specialty Symbol I216AZ ........................................................................................... 345
Instrument Specialty Symbol I219AZ ........................................................................................... 345
Instrument Specialty Symbol I237AZ ........................................................................................... 346
Contents
Instrument Specialty Symbol I253AZ ........................................................................................... 346
Instrument Specialty Symbol I301AZ ........................................................................................... 347
Instrument Specialty Symbol I324CZ ........................................................................................... 347
Instrument Specialty Symbol I324DZ ........................................................................................... 348
Instrument Specialty Symbol I324EZ ........................................................................................... 348
Instrument Specialty Symbol I324FZ ........................................................................................... 349
Miscellaneous Symbols ...................................................................................................................... 349
Miscellaneous Symbol OP3 ......................................................................................................... 349
Miscellaneous Symbol OP4 ......................................................................................................... 350
Miscellaneous Symbol OP5 ......................................................................................................... 350
Miscellaneous Symbol OP9373 ................................................................................................... 351
Miscellaneous Symbol OP_251 ................................................................................................... 351
Miscellaneous Symbol OP_271 ................................................................................................... 352
Miscellaneous Symbol OP_291 ................................................................................................... 352
Miscellaneous Symbol OP_292 ................................................................................................... 353
Miscellaneous Symbol OP_311 ................................................................................................... 353
Miscellaneous Symbol OP_331 ................................................................................................... 354
Miscellaneous Symbol OP_332 ................................................................................................... 354
Miscellaneous Symbol OP_333 ................................................................................................... 355
Miscellaneous Symbol OP_334 ................................................................................................... 355
Miscellaneous Symbol OP_351 ................................................................................................... 356
Miscellaneous Symbol OP_391 ................................................................................................... 356
Miscellaneous Symbol OP_401 ................................................................................................... 357
Miscellaneous Symbol OP_411 ................................................................................................... 357
Miscellaneous Symbol OP_412 ................................................................................................... 358
Miscellaneous Symbol OP_413 ................................................................................................... 358
Miscellaneous Symbol OP_451 ................................................................................................... 359
Miscellaneous Symbol OP_452 ................................................................................................... 359
Miscellaneous Symbol OP_453 ................................................................................................... 360
Miscellaneous Symbol OP_491 ................................................................................................... 360
Miscellaneous Symbol OP_492 ................................................................................................... 361
Miscellaneous Symbol OP_493 ................................................................................................... 361
Miscellaneous Symbol OP_494 ................................................................................................... 362
Miscellaneous Symbol OP_571 ................................................................................................... 362
Miscellaneous Symbol OP_572 ................................................................................................... 363
Miscellaneous Symbol OP_573 ................................................................................................... 363
Miscellaneous Symbol OP_574 ................................................................................................... 364
Miscellaneous Symbol OP_711 ................................................................................................... 364
Miscellaneous Symbol OP_731 ................................................................................................... 365
Miscellaneous Symbol OP_811 ................................................................................................... 365
Miscellaneous Symbol OP_851 ................................................................................................... 366
Miscellaneous Symbol OP_852 ................................................................................................... 366
Miscellaneous Symbol OP_853 ................................................................................................... 367
Miscellaneous Symbol OP_854 ................................................................................................... 367
Miscellaneous Symbol A1003 ...................................................................................................... 368
Miscellaneous Symbol A1005 ...................................................................................................... 368
Miscellaneous Symbol A1251 ...................................................................................................... 369
Miscellaneous Symbol A1331 ...................................................................................................... 369
Miscellaneous Symbol A1332 ...................................................................................................... 370
Miscellaneous Symbol S2003 ...................................................................................................... 370
Miscellaneous Symbol S3003 ...................................................................................................... 371
Bio-Pharmaceutical SpecificationComponent Symbols ...................................................................... 371
Bio-Pharm Specification Component Symbol FERR ................................................................... 371
10
Contents
Bio-Pharm Specification Component Symbol FERS .................................................................... 372
Bio-Pharm Specification Component Symbol CAPT .................................................................... 372
Bio-Pharm Specification Component Symbol CAPSE ................................................................. 373
Bio-Pharm Specification Component Symbol HA ........................................................................ 373
Bio-Pharm Specification Component Symbol FA ......................................................................... 374
Bio-Pharm Specification Component Symbol FAS ...................................................................... 374
Bio-Pharm Specification Component Symbol MA ........................................................................ 375
Bio-Pharm Specification Component Symbol MAR ..................................................................... 375
Bio-Pharm Specification Component Symbol B90T ..................................................................... 376
Bio-Pharm Specification Component Symbol B90TC .................................................................. 377
Bio-Pharm Specification Component Symbol B90C .................................................................... 378
Bio-Pharm Specification Component Symbol B45T ..................................................................... 379
Bio-Pharm Specification Component Symbol B45TC .................................................................. 379
Bio-Pharm Specification Component Symbol B45C .................................................................... 380
Bio-Pharm Specification Component Symbol R180R .................................................................. 380
Bio-Pharm Specification Component Symbol R180C .................................................................. 381
Bio-Pharm Specification Component Symbol TT ......................................................................... 381
Bio-Pharm Specification Component Symbol TTRB .................................................................... 382
Bio-Pharm Specification Component Symbol TCB ...................................................................... 383
Bio-Pharm Specification Component Symbol TRCB ................................................................... 384
Bio-Pharm Specification Component Symbol TSCB .................................................................... 385
Bio-Pharm Specification Component Symbol TRSCB ................................................................. 385
Bio-Pharm Specification Component Symbol TICB ..................................................................... 386
Bio-Pharm Specification Component Symbol TSCR ................................................................... 386
Bio-Pharm Specification Component Symbol XT ......................................................................... 387
Bio-Pharm Specification Component Symbol XTRB .................................................................... 388
Bio-Pharm Specification Component Symbol XC ........................................................................ 389
Bio-Pharm Specification Component Symbol TC ........................................................................ 390
Bio-Pharm Specification Component Symbol TCR ...................................................................... 391
Bio-Pharm Specification Component Symbol TCSB .................................................................... 392
Bio-Pharm Specification Component Symbol TCRSB ................................................................. 392
Bio-Pharm Specification Component Symbol TCI ....................................................................... 393
Bio-Pharm Specification Component Symbol RCP ...................................................................... 393
Bio-Pharm Specification Component Symbol RCCL ................................................................... 394
Bio-Pharm Specification Component Symbol RCC ..................................................................... 394
Bio-Pharm Specification Component Symbol REP ...................................................................... 395
Bio-Pharm Specification Component Symbol RECL .................................................................... 395
Bio-Pharm Specification Component Symbol REC ...................................................................... 396
Bio-Pharm Specification Component Symbol CHA ...................................................................... 396
Bio-Pharm Specification Component Symbol C2HD ................................................................... 397
Bio-Pharm Specification Component Symbol C3HD ................................................................... 397
Bio-Pharm Specification Component Symbol CPAN ................................................................... 397
Bio-Pharm Specification Component Symbol CPHB ................................................................... 398
Bio-Pharm Specification Component Symbol CA ........................................................................ 398
Bio-Pharm Specification Component Symbol CSJ ...................................................................... 398
Bio-Pharm Specification Component Symbol CHD ..................................................................... 399
Bio-Pharm Specification Component Symbol VS2D .................................................................... 399
Bio-Pharmaceutical Operators ............................................................................................................ 401
Bio-Pharm Operator Symbol SOP_3 ............................................................................................ 401
Bio-Pharm Operator Symbol SOP_42 .......................................................................................... 402
Bio-Pharmaceutical Specialty Components ........................................................................................ 403
Bio-Pharm Specialty Component Symbol R180B ........................................................................ 403
Bio-Pharm Specialty Component Symbol R180S ........................................................................ 404
11
Contents
Bio-Pharm Specialty Component Symbol VSDTP ....................................................................... 404
Bio-Pharm Specialty Component Symbol VSDTC ....................................................................... 405
Bio-Pharm Specialty Component Symbol VSCCB ....................................................................... 405
Bio-Pharm Specialty Component Symbol VSCCBU425 .............................................................. 405
Bio-Pharm Specialty Component Symbol VS3WD ...................................................................... 406
Bio-Pharm Specialty Component Symbol VS4WD ...................................................................... 407
Details Assumed ................................................................................................................................. 407
Detail V1 ....................................................................................................................................... 407
Detail V2 ....................................................................................................................................... 408
Detail V3 ....................................................................................................................................... 408
Detail V4 ....................................................................................................................................... 409
Detail V5 ....................................................................................................................................... 409
Detail V7 ....................................................................................................................................... 410
Detail V8 ....................................................................................................................................... 410
Detail H1 ....................................................................................................................................... 411
Detail H2 ....................................................................................................................................... 411
Detail H3 ....................................................................................................................................... 412
Detail H4 ....................................................................................................................................... 412
Detail F1 ....................................................................................................................................... 413
Detail F2 ....................................................................................................................................... 413
Detail F4 ....................................................................................................................................... 414
Detail F7 ....................................................................................................................................... 414
Detail F8 ....................................................................................................................................... 415
Detail P1 ....................................................................................................................................... 415
Detail P2 ....................................................................................................................................... 416
Detail P3 ....................................................................................................................................... 416
Detail P4 ....................................................................................................................................... 417
Detail P5 ....................................................................................................................................... 417
Detail P7 ....................................................................................................................................... 418
Detail P8 ....................................................................................................................................... 418
Detail P9 ....................................................................................................................................... 419
Detail T1 ....................................................................................................................................... 419
Detail T ......................................................................................................................................... 420
Detail T4 ....................................................................................................................................... 420
Detail L1 ....................................................................................................................................... 421
Detail L2 ....................................................................................................................................... 421
Detail L4 ....................................................................................................................................... 422
Detail L7 ....................................................................................................................................... 423
Detail L8 ....................................................................................................................................... 424
Piping and Instrument Symbol Notes ................................................................................................. 425
Assembly Notes .................................................................................................................................. 432
Commodity Code Descriptions .............................................................................................................. 435
Commodity Code Matrix ..................................................................................................................... 435
Flanged and Miscellaneous Fittings ................................................................................................... 436
Completing Materials .......................................................................................................................... 441
Fire and Safety Components .............................................................................................................. 442
Steam Specialties ............................................................................................................................... 443
Flanges ............................................................................................................................................... 446
Flanged Fittings................................................................................................................................... 453
Strainer Specialties ............................................................................................................................. 459
Instrument Specialties ......................................................................................................................... 465
Pipe Supports...................................................................................................................................... 475
12
Contents
Labor Codes........................................................................................................................................ 488
Miscellaneous Wetted Fittings ............................................................................................................ 496
Miscellaneous Non-Wetted Fittings .................................................................................................... 497
Tubing and Hose ................................................................................................................................. 499
Pipe ..................................................................................................................................................... 504
Socket Fittings..................................................................................................................................... 516
Tubing Fittings..................................................................................................................................... 518
Socketwelded Fittings ......................................................................................................................... 524
Threaded Fittings ................................................................................................................................ 527
Underground Fittings .......................................................................................................................... 532
Valves ................................................................................................................................................. 535
Welded Fittings ................................................................................................................................... 551
Gaskets ............................................................................................................................................... 559
Bolting ................................................................................................................................................. 566
Calculations From ANSI-B31.1 and ANSI-B31.3 ................................................................................... 573
Codelists................................................................................................................................................... 577
General Comments ............................................................................................................................. 579
Comments Specific to Units of Measure Codelist Sets ...................................................................... 579
CL31, Object Types for Orthographic Drawings (40).......................................................................... 581
CL35, Approval Status (10) ................................................................................................................. 583
CL36, Structural Approval Status (15) ................................................................................................ 583
CL37, HVAC Approval Status (10)...................................................................................................... 584
CL50, Hold Status (10) ....................................................................................................................... 584
CL69, Equipment Divisions/Form Code (99) ...................................................................................... 584
CL125, Fluid Code/Connector Type (999) .......................................................................................... 585
CL130, Construction Status (15) ......................................................................................................... 589
CL145, Materials Grade (4500) .......................................................................................................... 589
CL148, Piping Materials Class Description (31999) ........................................................................... 625
CL160, Responsibility (25) .................................................................................................................. 636
CL180, Fabrication Category (99)....................................................................................................... 636
CL190, Coating Requirements (99) .................................................................................................... 637
CL200, Heat Tracing Requirements (10) ............................................................................................ 637
CL210, Heat Tracing Media (60) ......................................................................................................... 638
CL220, Insulation Purpose (40) .......................................................................................................... 639
CL230, Cleaning Requirements (99) .................................................................................................. 639
CL330, CP Type/Termination/Preparation (999) ................................................................................ 639
CL332, Schedule / Thickness Override .............................................................................................. 643
CL340, Safety Classification (99)........................................................................................................ 645
CL360, Stress Analysis Requirements (15) ........................................................................................ 645
CL365, Reporting Requirements (25) ................................................................................................. 645
CL366, Requirement to Reconstruct (10) ........................................................................................... 646
CL380, Piping Component Type (2500) ............................................................................................. 646
CL390, Action (40) .............................................................................................................................. 655
CL400, Option (999) ........................................................................................................................... 655
CL420, Piping Component Type/Source (25) ..................................................................................... 664
CL425, Piping/Tubing Type (25) ......................................................................................................... 664
CL430, Instrument Component Type/Source (25) .............................................................................. 664
CL499, Piping Notes (999) .................................................................................................................. 664
CL530, Accessory/Item Type (125) .................................................................................................... 667
CL550, Operator/Actuator Type (200) ................................................................................................ 667
CL570, Design Standard (200) ........................................................................................................... 669
13
Contents
CL572, Wall Thickness Equation ........................................................................................................ 669
CL575, Geometry Standard (31999)................................................................................................... 669
CL576, Table Suffix/End Standard - Green (999) ............................................................................... 684
CL577, Table Suffix/End Standard - Red (999) .................................................................................. 688
CL578, Weight Code (399) ................................................................................................................. 692
CL990, Types of Piping Commodity Data Forms ............................................................................... 694
CL999, Standard Note Title (2000) ..................................................................................................... 695
CL1010, Area Units (25) ..................................................................................................................... 696
CL1028, Mass Units (40) .................................................................................................................... 697
CL1056, Temperature Units (15) ........................................................................................................ 697
CL1064, Pressure Units (40) .............................................................................................................. 698
CL1074, Density Units (35) ................................................................................................................. 699
CL1100, Weld Type (100) ................................................................................................................... 699
CL1162, Force Units (40) .................................................................................................................... 699
CL1201, Drawing Scale (540) ............................................................................................................. 700
CL1202, Drawing Size (199) ............................................................................................................... 700
CL1203, Interference Manager Approval Status (99) ......................................................................... 700
CL1204, Interference Clash Type ....................................................................................................... 700
CL1205, Interference Manager Action (10) ........................................................................................ 703
CL1207, Interference Manager Approval Method (10) ....................................................................... 703
CL1208, Clash Checking Option......................................................................................................... 703
CL1209, Clash Checking Volume Filter Option .................................................................................. 703
CL1310, Report Source (99) ............................................................................................................... 703
CL1312, Report Type (999) ................................................................................................................ 703
CL1410, Design Review Type (10) ..................................................................................................... 704
CL1605, Model Status ........................................................................................................................ 704
CL1610, Force Units for FrameWorks Plus (40) ................................................................................. 704
CL1620, Drawing View Directions (7) ................................................................................................. 705
CL1630, Drawing View Composition Status (4) .................................................................................. 705
CL1710, Document Source (99) ......................................................................................................... 705
CL1720, Document Type (999) ........................................................................................................... 706
CL1900, Isometric Drawing Type ........................................................................................................ 708
CL2000, PD_Draw Document Type (999) .......................................................................................... 709
Index ......................................................................................................................................................... 711
14
Preface PDS
This document provides command reference information and procedural instructions for the Plant
Design System (PDS) Piping Component Data task.
15
SECTION 1
Introduction
This document explains the basis used in developing the Reference Data required for the
execution of the Piping Task.
See Also
Reference Data File Descriptions (on page 17)
Piping Job Specification File Descriptions (on page 17)
Non-Database Part of the Piping Job Specification (on page 18)
Non-Database Part of Item Descriptions (on page 19)
Model Graphics (on page 19)
Design DDL (on page 20)
Seed File Definitions (on page 20)
17
Introduction
240
241
242
243
18
Introduction
Model Graphics
The files involved and a short description are given below. Refer to the description of the Graphic
Commodity Library in the Reference Data Manager (PD_Data) Reference Guide for detailed
explanations.
c:\win32app\ingr\rdusrdb\us_pcdim.l.t
This file contains data in the format required for definition and revision. It includes all the
tables required to provide dimensions, surface area and weight data to the Piping Task during
interactive execution of the task. In addition to generic data, it includes specific data about:
Plain piping components
Valves
Fittings
Fire and safety components
Miscellaneous piping commodity components, including valve operators
c:\win32app\ingr\rdusrdb\us_pcdim.l
This library file contains data in the format required for execution by the task. It includes data
from all the sources listed in the description of c:\win32app\ingr\rdusrdb\us_pcdim.l.t.
c:\win32app\ingr\pdshell\lib\assembly.l.t
This file contains data in the format required for definition and revision. It includes the
definitions of all assemblies available for use with the task.
c:\win32app\ingr\pdshell\lib\assembly.l
This library file contains data in the format required for execution by the task. It includes data
from all the assemblies included in c:\win32app\ingr\pdshell\lib\assembly.l.t.
19
Introduction
Design DDL
The file involved and a short description are given below.
c:\win32app\ingr\pdshell\ddl\design.ddl
This is the database definition of the relational database for the Design portion of the Piping
Task.
Files(s)
c:\win32app\ingr\rdusrdb\spec_data\*
c:\win32app\ingr\pddata\sample\data\pcd_size.d
ata
c:\win32app\ingr\rdusrdb\us_pjstb.l
Notes
c:\win32app\ingr\pdshell\lib\std_note.l
Item Descriptions
Piping Commodities Short
Descriptions
c:\win32app\ingr\rdusrdb\us_shbom.l
c:\win32app\ingr\rdusrdb\us_lgbom.l
c:\win32app\ingr\rdusrdb\us_spbom.l
Labels
c:\win32app\ingr\pdshell\lib\labels.l
c:\win32app\ingr\pdshell\lib\pip_gcom.l
c:\win32app\ingr\rdusrdb\us_pcdim.l
Assemblies
c:\win32app\ingr\pdshell\lib\assembly.l
Miscellaneous
20
Color Table
c:\wc:\win32app\ingr\pdshell\seedz\*sdz.dgnin3
2app\ingr\pdshell\color\*
c:\win32app\ingr\pdshell\seedz\*sdz.dgn
Introduction
Description
Files(s)
Report Formats
c:\win32app\ingr\pdreport\sample\*.fmt
c:\win32app\ingr\pddata\sample\format\*.fmt
c:\win32app\ingr\pdprojec\sample\*.fmt
c:\win32app\ingr\pdclash\sample\*.fmt
21
APPENDIX A
General Conventions
Unless otherwise indicated in this document, values for "specific" and "generic" parameters
will be stored in tables whose names are derived from parameters in the Piping Job
Specification.
Table names often use the character "_".
Any number of comments may be included in a table, using the convention described below:
Blank lines are allowed without limits. No special character is required to define their
presence.
Any number of lines with comments may be included. Each comment line must be
preceded by an "!". Comments are disregarded by the system.
The following comments are specific to the Piping Job Specification Table, to the Piping
Commodities Table and to the Taps Table:
Columns in the table may be separated by either single or double spaces. The following
comments apply:
If single spacing is preferred, a line with the following format is required:
Single_Spacing
Entries in the columns must be made without blank spaces.
If double spacing is preferred, a line with the following format is required:
Double_Spacing
Entries in the columns may have up to one blank space in them.
A sequence line will define the contents of each column in the table. This will be done by
identifying the attribute number from the applicable entity and DDL covered by each column.
Attributes that are not included in the table will be defined by preceding them with an "*". An
example is:
Sequence= 1 2 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 *3 *4
The spacing between the entries in the above order statement must be either single or double
depending upon whether the single or double format applies to the table. This includes the
space between "=" and the first number in the statement.
Units will be defined for each column of a table as the applicable of the codes shown below.
The indicated upper/lower case convention should be respected.
Measurement
Type
Angle
Degrees
DEG
Degrees
DEC
Area
Square feet
FT2
Area
Square inches
IN2
Area
Square miles
Area
Area
Square yards
Square centimeters
MI2
YD2
SCM
23
General Conventions
Measurement
Type
Area
Square kilometers
Codelisted attributes
INT
Density
GCM3
Density
KG_DM3
Density
Density
Density
Density
KG_L
KIPFT3
Density
Density
UKGAL
Density
USGAL
Density
KGM3
Insulation Thickness
24
SKM
Inches
LBF3
IN
Insulation Thickness
Millimeters
MM
Length
Inches
IN
Length
Inches (decimal) I
N_DEC
Length
Millimeters (decimal)
MM_DEC
Mass
Grams
Mass
Grains
GRAIN
Mass
Kilograms
KG
Mass
Milligrams
MG
Mass
Tons (UK)
UKTON
Mass
Tons (US)
USTON
Nominal diameter
Inches
NPD_IN
Nominal diameter
Millimeters
NPD_MM
Pressure
Atmospheres
ATM
Pressure
Bars (Absolute)
BAR
Pressure
Bars (Gauge)
BAR_G
Pressure
Inches of water
INH2O
General Conventions
Measurement
Type
Pressure
Inches of water at 32
degrees F
INH2O_32F
Pressure
Inches of mercury
INHG
Pressure
Inches of mercury at 32
degrees F
INHG_32F
Pressure
KG_CM2
Pressure
KG_CM2_A
Pressure
Pressure
Kilogram-force per
millimeter
KGF_MM
Pressure
KN_M
Pressure
Kilonewtons per
millimeter
KN_MM
Pressure
Kilopascals (Gauge)
KPA_G
Pressure
LB_FT
Pressure
LB_IN
Pressure
Millimeters of water
MMH2O
Pressure
Millimeters of mercury
(Torr)
MMHG
Pressure
Megapascals (Gauge)
MPA_G
Pressure
N_M
Pressure
N_MM
Pressure
Pascals (Gauge)
PAG
Pressure
PSIG
Density
USTONFT3
Rating
Schedule/Thickness
Inches
SC_TH_IN
Schedule/Thickness
Millimeters
SC_TH_MM
Stress
PSI
Stress
Pascals (Absolute)
PA
Stress
Kilopascals (Absolute)
KPA
25
General Conventions
26
Measurement
Type
Stress
Megapascals (Absolute)
MPA
Surface area
Square feet
SF
Surface area
Square meters
SM
Surface area
Square millimeters
SMM
Surface area/unit
SFF
Surface area/unit
Surface area/unit
SMM_M
Temperature
Degrees Celsius
DC
Temperature
Degrees Fahrenheit
DF
Temperature
Degrees Kelvin
DK
Temperature
Degrees Rankin
DR
Unitless alphanumeric
Unitless integer
INT
DEC
Weight
Pounds
LB
Weight
Kilograms
KG
Weight/unit
LBF
Weight/unit
Kilograms per meter
KGM
All entries in the tables will be left justified.
Field locations and field lengths defined with XXXXs, WWWWs and ZZZZZs in this document
will be observed.
Fractions will not be used in defining any table value. They will be expressed in their decimal
equivalents.
Adjacent columns in a table will be separated by one or more spaces.
If a value in a table is not known, a "-" must be used in the corresponding field. The system
will interpret this entry to represent a blank value and such will be displayed in reports,
drawings and other such formal data outputs to the User. The dash shall not be enclosed in
quote marks, even if the field is for an alphanumeric value.
Real numbers without decimals may be expressed with or without a decimal point. For
example, a nominal diameter of twenty inches may be expressed as "20", or "20." or "20.0".
For the sake of consistency, all tables will show the value as "20".
All alphanumeric values in a table must be enclosed in single quotes; for example, 'ZZZZZZZ'.
General Conventions
For tables with only one input column, the generic value ET_AL may be used in the input
column. The system will understand such entry to indicate that values in the line just prior to
that for ET_AL will apply to any input value equal to or greater than the value in that line.
The following conventions will apply to the definition of columns in a table with a table format
other than P8*, P9*, I8* or I9*, where * refers to any applicable alphanumeric character:
A definition must be made using the format described below regarding the number of
input and output columns involved:
No Inputs X No Outputs X
The number of input columns must not exceed 2. The number of output columns must
not exceed 9; it may be 0.
A definition must be made using the format described below regarding the units of
measure used in each column.
Units= NPD IN, SF, LB, INT, DEC, IN, RAT, IN, IN, IN
The following conventions will apply to the definition of data in a table with table format P8*,
P9*, I8* or I9*:
A definition does not need to be made regarding the number of input and output columns
involved. The number of input fields must not exceed 2. The number of output fields is
up to parameter P34 for component data and up to parameter Y27 for actuator data. A
blank line following a component will signify that the definition of the component has been
completed and that a new component will follow. The word "END" following a
component will signify the end to the table.
Each parameter in these tables must have the applicable units of measure defined, using
the format "Pii-Z" or "Yii-Z", where:
-A=AN*20
-D=AN*1
-E=INT
-G=NPD IN
-H=NPD MM
-J=SF
-L=LB
-N=IN
-P=DEG
The following conventions apply to the attribute "rating" with respect to the naming of data
tables:
The Piping Job Specification may express alphanumeric ratings in at least the following
formats: CLXXXX, XXXX# or OTXXXX. The entry in the table and the file names
representing the attribute "rating", however, will exclude characters such as "CL", "#" and
"OT" so that the same table may be used regardless of how rating was defined in the
Piping Job Specification. The above rating formats have been used in accordance with
the following criteria:
CLXXXX to refer to an ANSI or API pressure rating.
XXXX# to refer to a pressure rating defined by an organization other ANSI or API.
OTXXXX to refer to the rating of a connect point that meets the applicable ANSI or
API rating geometrically but not from a pressure carrying standpoint. An example of
the above is a valve supplied with flanged ends meeting the bolting pattern of ANSI
CL150 pressure rating but having pressure carrying characteristics different from
those of that ANSI rating.
Female ends for plastic pipe are usually defined in terms of "schedule/thickness" and not
in terms of "rating" as is common with female ends for most other components. To make
27
General Conventions
28
female ends for plastic pipe follow the rules for other female ends, the applicable
"schedule/thickness" will be used as the value for "rating" for these components. If such
rating values consist of alphanumeric characters (including dashes), the system will
"strip" all such characters from the rating value in the Piping Job Specification and will
only use the numeric values in accessing the applicable tables. If such rating values
include decimal points, the decimal points will be converted to the character "$" in
accessing the applicable tables.
If the rating in the Piping Job Specification is expressed in terms of alphabetic characters
only, the system will use all such characters in accessing the data tables. The names of
the data tables will include all the alphabetic characters included in the Piping Job
Specification.
Another acceptable value for rating is "GRAVHD". This value may be used in the
Piping Job Specification and in the data tables for components rated to sustain a
nominal fluid head.
Another acceptable value for rating is "OTHER".
One acceptable value for rating is "NONE". This value may be used in the Piping Job
Specification and in the data tables for components whose ends would normally
require the use of the attribute rating as part of the table name but that for some
specific reason, a rating does not apply.
The schedule/thickness of piping components may be determined either by
look-up/calculation from a piping materials class or based on a value provided by the User
independent of the piping materials class. Comments in this paragraph define the latter
approach. The value of the override schedule/thickness attribute of each piping segment
may be either:
Left blank if the User wishes schedule/thickness to be determined from the applicable
piping materials class; or
Defined by the User entering a schedule/thickness value; or
Defined by data transfer from the P&ID Task. A value from the P&ID Task will only be
transferred to this attribute if the piping thickness flag in the P&ID segment has a value "
U"; in such case, the value from the P&ID segment schedule/thickness will be transferred
to the Piping Task override schedule/thickness. Otherwise, the value of the override
schedule/thickness in the Piping Task will be left blank
If the Piping Task software finds a non-blank value for the override schedule/thickness,
such value will be applied to all the components that belong to the segment. Such
definition will be respected during reconstruction of the piping system.
Schedule or thickness values will be shown for all components for which such values make
sense. In order of preference, schedule and thickness will be expressed in terms of:
Generic schedules, such as S-STD, S-XS and S-XXS.
Specific schedules, such as S-40, S-60 and S-80.
Thickness class, such as CL50 and CL51. For this situation, both the alpha and numeric
characters must be included in the "Sc/Th" column of the piping materials class and in the
corresponding table names.
"NREQD": This value is to be used in cases where all of the following conditions apply:
+ The thickness value is not required in purchasing the component.
+ Empty weights are not significantly affected by actual thickness values.
+ Either stress analysis is not applicable or, if applicable, the component is to be
considered infinitely rigid in stress analysis calculations.
General Conventions
Specific wall thicknesses: To insure compatibility between data tables, the Piping Job
Specification and wall thickness calculations, thickness will be expressed as defined
below.
+ .XXXX if the thickness is less than 1 inch
+ X if the thickness is an even inch
+ X.XXX if the thickness is 1 inch or thicker
Trailing zeroes will not be included. Decimal points will not be included for numbers
without decimals. Examples of these rules follow: + .25 + .5 + 1 + 1.375 + 2.375
Where the schedule name exceeds the field length provided, for example S-SDR13.5, it
will be defined in terms of its wall thickness.
*XYYY: The need to perform a thickness calculation will be triggered by an entry with the
format "*XYYY" being present in the "Sc/Th" column of the Piping Commodities Table.
The letters that make this code have the following meaning:
The character "X" is an alphanumeric code that defines the equation to use in the
calculation. Possible values and their definitions are as follows: If the value for this
character is "C", the schedule/thickness for the applicable end of the component is to
be determined by calculations using the thickness equation defined for the piping
materials class in the "Thck Eqtn" column of the Define Piping Job Specification table.
The characters "YYY" define the casting, joint or structural grade quality factor (E)
times 100. This factor is one of the parameters used in the thickness calculation.
The User should be cautioned that if he is defining a calculation to be performed on a
seamless fitting (E=1) but wishes to match the thickness for the mating welded pipe
(E=0.85), the quality factor for the pipe should be entered here.
MATCH: The need to match the thickness of a component to that of the pipe of the same
diameter and of option 1 will be triggered by an entry with the format "MATCH" being
present in the "Sc/Th" column of the Piping Commodities Table.
29
General Conventions
To minimize duplication when the same thickness can be expressed for metallic materials in
terms of either a generic or a specific schedule, the convention defined below will be used.
For a given nominal diameter, only the schedules shown in the line for that diameter will be
used in the Piping Job Specification and in the data tables.
The table shown below will be used to correlate English nominal pipe diameters with their
corresponding metric values.
Nominal Pipe Diameter
in
30
mm
0.125
0.250
0.375
10
0.500
15
0.750
20
General Conventions
1.000
25
1.250
32
1.500
40
2.000
50
2.500
65
3.000
80
3.500
90
4.000
100
5.000
125
6.000
150
8.000
200
10.00
250
12.00
300
14.00
350
16.00
400
18.00
450
20.00
500
22.00
550
24.00
600
26.00
650
28.00
700
30.00
750
32.00
800
34.00
850
36.00
900
38.00
950
40.00
1000
42.00
1050
44.00
1100
46.00
1150
48.00
1200
Weight tables have been provided for components required by the piping materials classes for
at least the combinations of thickness shown in the applicable Thicknesses Tables.
Where a "." or a "-" is included in a parameter that is part of a table name, a "$" will be used to
represent them in both the table name and the ASCII file name. The actual character, and
31
General Conventions
not the "$", will be displayed in all fields representing the actual attribute involved. Examples of
how thicknesses would be represented on the basis of the above rule follow:
.25 .........................................$25
.5 ..........................................$5
1 ...........................................1
1.375 .......................................1$375
2.375 .......................................2$375
Some tables require an "END" statement as their last line; others do not. Refer to specific
table formats in this document for actual requirements.
Revision management of Piping RDB data follows the conventions described below:
The applicable control document is updated.
The "Rev" and "Date" fields of the table that is changed are revised as appropriate.
The line in the table that was either newly created or revised is identified by having the
symbol ">" precede it. If the line was deleted, a ">" is placed above and below the line
deleted.
When a table is revised again, all previous revision marks are deleted.
End Type
Explanation
Any
Bolted
Male
Not applicable.
Female
Any
Bolted
Male
Not applicable.
32
General Conventions
Variables
BCD
End Type
Explanation
Female
Bolted
Male
Not applicable.
Female
Not applicable.
Any
Bolted
Male
Not applicable.
Female
Any
Bolted
Male
Not applicable.
Female
Any
Bolted
Male
33
General Conventions
Variables
End Type
Explanation
Female
Any
Bolted
Male
Female
Any
Bolted
Male
Female
Any
Bolted
Male
Female
I,J,K,L,M,N
Any
Any
34
General Conventions
End Type
Explanation
Bolted
Male
Female
For PVC and CPVC female ends: same as the value of "P" for
the corresponding male termination type.
For all other female ends: 30% of the fitting OD at the female
end plus 70% of the matching pipe OD.
Bolted
Not applicable
Male
The value of this variable will be "0" for all male ends.
Female
35
General Conventions
Variables
End Type
Explanation
Bolted
Male
Not applicable
Female
Not applicable
Bolted
Male
Not applicable
Female
Not applicable
Bolted
Male
Not applicable
Female
Not applicable
Bolted
36
General Conventions
Variables
End Type
Explanation
Male
Not applicable
Female
Not applicable
Bolted
W_i
Male
Not applicable
Female
Not applicable
Bolted
37
General Conventions
Variables
End Type
Explanation
(+ or no sign modifier value) or machine bolts (- modifier value)
using special nut allowances. This parameter will be used in
calculating the length of bolts required in a bolted connection.
Values for W_0 and W_1 were developed on the following
basis:
Male
Not applicable
Female
Not applicable
Bolted
Not applicable
Male
Female
Not applicable.
Any
38
Any
APPENDIX B
Commodity Discussions
Piping Commodity Data
This section defines requirements which are specific to piping components.
See Also
Basic Information (on page 39)
Non-parametric and Parametric Piping and Tubing (PIPING, TUBING) (on page 40)
Valves (6Q1C) (on page 43)
On-line Fittings (6P2C) and In-line Fittings (6Q2C) (on page 74)
On-line Fittings (6P3C) and In-line Fittings (6Q3C) (on page 106)
Basic Information
AABBCC Codes and Model Codes
The AABBCC code is the primary access key to the commodity items in the Piping Job
Specification. An AABBCC code is a generic code about which a more detailed definition is made
in the Piping Job Specification.
These detailed definitions are identified by a model code in the Commodity Item data table of the
PJS. Each model code is classified by:
AABBCC code
option
size ranges
end preparations
ratings
The model code includes the definition of the graphic representation of the component in the
piping model. Depending upon the circumstances:
One or more model codes can be assigned to one AABBCC code
The same model code can be assigned to different AABBCC codes.
39
Commodity Discussions
If the termination types are the same but the values for rating, schedule or thickness differ,
the "stronger" ends(s) are designated as the green connect point.
Abbreviations
The following abbreviations are used to describe the table name formats in this document.
(G) (R) Angle BrchTbl
GS MC
TS
Table Suffix
WC
Weight Code
40
Commodity Discussions
Male threaded/plain ends
Beveled/male grooved ends
Male threaded/male grooved ends
Male grooved/plain ends
Plain/plain 3" field fit ends
Plain/plain 6" field fit ends
For GCP: Rating="-"; Sc/Th="Value"
For RCP: Rating="-"; Sc/Th="Value"
For certain types of pipe, for example, reinforced concrete, the thickness is actually
determined by the Fabricator on the basis of specified conditions. For them, the value
"NREQD" is used for Sc/Th.
TNF=None & None
Spigot/push-on bell ends
Plain/push-on bell ends
For GCP: Rating="-"; Sc/Th="Value"
For RCP: Rating="Value"; Sc/Th="NREQD"
The following comments apply to the above definition of piping:
No EDEN parametric code definition is required for its placement.
Both ends of the pipe have different end preparation. Pipe placement must always start at
a fitting. The end preparation of the fitting will determine the end preparation of the pipe
which will be placed first. When pipe placement is completed, the end preparation of the
last end of the pipe will be checked for compatibility with that of the corresponding fitting
end, if one applies. If an incompatibility is detected with such fitting end, an error will be
returned by the system.
The pipe length is determined at placement either by key-in of actual length or by stringing
the pipe between two pre-existing components. The system will refuse to place portions
of piping, which are shorter that the "min length" value defined in table PIPE_LENGTH.
The system will return a warning if the user places a section of piping which is shorter than
the "preferred length" value defined in table PIPE_LENGTH.
Placement of taps is neither required nor possible.
Purchased Length Pipe
Purchased length pipe has its length defined in the pds_sort_code attribute of the Piping
Commodity Specification Data Table of the Material Reference Database. Purchased
length pipe, can be placed or extended such that the remainder length of the last pipe does
not exceed the pipe length threshold, as specified in the active Pipe Length Threshold Table.
The following considerations apply to the length of this type of pipe:
During manual component placement, the system will place, starting at the active
placement point, one length of pipe of the default length. If the available length is less than
the default length, a pipe will be placed to fit the available length. By choosing the
starting point for placement, the user will have control as to where the random length of
pipe is placed.
During automatic component placement, the system will start placing pipe of the default
length from whichever end applies and will continue doing so until the available length for
placement is less than the default length. An additional pipe will then be placed to fit the
remaining length. In this method of placement, the user has no control as to where the
random length of pipe is placed.
The system will refuse to place any portion of piping, which are shorter that the "min
length" value defined in table PIPE_LENGTH. The system will return a warning if the
41
Commodity Discussions
user places a section of piping which is shorter than the "preferred length" value defined in
table PIPE_LENGTH.
TNF=None & None
Flanged/mechanical joint ends
Mechanical joint/plain ends
For GCP: Rating="Value"; Sc/Th="Value"
For RCP: Rating="Value"; Sc/Th="Value"
TNF=None & None
Spigot/push-on bell ends
Plain/push-on bell ends
Plain/mechanical joint bell ends
For GCP: Rating="-"; Sc/Th="Value"
For RCP: Rating="Value"; Sc/Th="NREQD"
The following comments apply to the above definition of piping:
In the Piping Materials Class, the entry for model code will be preceded by an asterisk (*)
to signify to the software that piping with an EDEN parametric code definition is involved.
This asterisk is not part of the model code name itself and such will be recognized by data
check reports executed by PDS. The ends of the piping will be drawn per the following
convention:
Bolted ends will be represented per standard PDS practice using dimensions from the
applicable generic tables.
Female ends will be represented as a cone of the following dimensions:
The large end with dimensions from the applicable female generic tables.
An included cone of angle of 90 degrees.
A cone length determined by the above criteria in conjunction with the termination
type at the other end of the pipe.
Both ends of the pipe have different end preparation. Pipe placement must always start at
a fitting. The end preparation of the fitting will determine the end preparation of the pipe
which will be placed first. When pipe placement is completed, the end preparation of the
last end of the pipe will be checked for compatibility with that of the corresponding fitting
end, if one applies. If an incompatibility is detected with such fitting end, an error will be
returned by the system. It will not be possible to "break" this type of pipe after placement
for insertion of another component; if such action was required, deletion and replacement
of the pipe will be necessary.
The following considerations apply to the length of this type of pipe:
The model code (MC) for parametric pipe will consist of the letter "P" followed by an
integer that will define its default length. This length will be the "CP to CP" length,
rather than the "face to face" length. It will have as units of measure those that apply
to pipe length in the project.
During manual component placement, the system will place, starting at the active
placement point, one length of pipe of the default length. If the available length is
less than the default length, a pipe will be placed to fit the available length. By
choosing the starting point for placement, the user will have control as to where the
random length of pipe is placed.
During automatic component placement, the system will start placing pipe of the
default length from whichever end applies and will continue doing so until the
available length for placement is less than the default length. An additional pipe will
then be placed to fit the remaining length. In this method of placement, the user has
no control as to where the random length of pipe is placed.
42
Commodity Discussions
During reconstruction, the system will replace default and non-default pipe lengths in
kind. If the new default length differs from the original default length, however, the
procedure define above for automatic component placement will be used.
The system will refuse to place any portion of piping, which are shorter that the "min
length" value defined in table PIPE_LENGTH. The system will return a warning if the
user places a section of piping which is shorter than the "preferred length" value
defined in table PIPE_LENGTH.
Placement of taps is required.
Valves (6Q1C)
The AABBCC code for valves consists of the AABB code 6Q1C followed by two numbers for the
specific type of valve.
The Piping Component database table (34) applies to these classes of piping components.
See Also
Connect Point Data (on page 44)
6Q1C01, Gate valve (in-line) (on page 50)
6Q1C02, Extended body gate valve (in-line) (on page 51)
6Q1C03, Conduit gate valve (in-line) (on page 52)
6Q1C04, Blank gate valve (in-line) (on page 52)
6Q1C05, 3-way valve (in-line) (on page 53)
6Q1C06, [2-way] ball valve (in-line) (on page 53)
6Q1C08, 3-way ball valve (in-line) (on page 54)
6Q1C11, [2-way] globe valve (in-line) (on page 55)
6Q1C12, [2-way] angle globe valve (in-line) (on page 56)
6Q1C13, 3-way globe valve (in-line) (on page 57)
6Q1C14, Y globe valve (in-line) (on page 57)
6Q1C16, [2-way] plug valve (in-line) (on page 58)
6Q1C18, 3-way plug valve (in-line) (on page 60)
6Q1C19, 4-way plug valve (in-line) (on page 60)
6Q1C22, Needle valve (in-line) (on page 60)
43
Commodity Discussions
6Q1C26, Butterfly valve (in-line) (on page 60)
6Q1C30, Diaphragm valve (in-line) (on page 61)
6Q1C32, Knife gate valve (in-line) (on page 62)
6Q1C33, [2-way] slide valve (in-line) (on page 62)
6Q1C34, 3-way slide valve (in-line) (on page 63)
6Q1C37, Angle valve (in-line) (on page 64)
6Q1C38, Check valve (in-line) (directional) (on page 64)
6Q1C39, Wafer check valve (in-line) (directional) (on page 67)
6Q1C40, Angle check valve (in-line) (directional) (on page 67)
6Q1C41, Stop check valve (in-line) (directional) (on page 68)
6Q1C42, Angle stop check valve (in-line) (directional) (on page 68)
6Q1C43, Y stop check valve (in-line) (directional) (on page 68)
6Q1C50, Backflow preventer (in-line) (directional) (on page 69)
6Q1C51, Automatic recirculation valve (in-line) (directional) (on page 69)
6Q1C53, Angle blowdown valve (in-line) (on page 69)
6Q1C54, Y blowdown valve (in-line) (on page 70)
6Q1C56, Pinch valve (in-line) (on page 70)
6Q1C57, Float valve (in-line) (on page 70)
6Q1C58, Foot valve (in-line) (directional) (on page 70)
6Q1C62, Tank drain valve (in-line) (directional) (on page 71)
6Q1C69, Deluge valve (in-line) (on page 71)
6Q1C72, Hose valve (in-line) (on page 71)
6Q1C73, Angle hose valve (in-line) (on page 72)
6Q1C76, Vent-drain valve (in-line) (on page 72)
6Q1C80, Instrument root valve (in-line) (on page 72)
6Q1C81, 3-way instrument root valve (in-line) (on page 73)
6Q1C82, 4-way instrument root valve (yn-line) (on page 73)
44
Commodity Discussions
The only independent variable in this table is the nominal diameter of the green connect point
of the component. The dependent variables are those dimensional parameters required to
display the component in the model that were not included in the P15A table.
For piping valves whose operator types as defined in codelist set CL550, Operator/Actuator
Type, are less than or equal to 24, the empty weight of the valve, including the valve operator
weight, is included in a table with format P59. The name of this table is comprised of the
following parameter from the piping commodities part of the Piping Job Specification:
Cmdty Code
The only independent variable in this table is the nominal diameter of the green connect point
of the component. The only dependent variable is empty weight of the valve, including its
operator.
For piping valves whose operator types as defined in codelist set CL550, Operator/Actuator
Type, exceed 24 and are less than or equal to 40, the empty weight of the valve exclusive of
the operator weight, the operator weight, the model code for the valve operator, the three
parameters that define the location of the center of gravity of the operator and up to two
dimensional parameters required to define the geometry of the valve operator is included in a
table with format P60A. The name of this table is comprised of the following parameter from
the piping commodities part of the Piping Job Specification:
Cmdty Code_WOPD_A
The only independent variable in this table is the nominal diameter of the green connect point
of the component. The dependent variables are the empty weight of the valve exclusive of
the operator weight, the operator weight, the model code of the operator, the three
parameters that define the location of the center of gravity of the operator and up to two
dimensional parameters required to define the geometry of the valve operator.
If columns available in the above table were insufficient to allow definition of all the applicable
dimensional parameters of the valve operator, the remaining parameters are included in a
table with format P60B. The name of the P60B table is comprised of the following parameter
from the piping commodities part of the Piping Job Specification:
Cmdty Code_WOPD_B
The only independent variable in this table is the nominal diameter of the green connect point
of the component. The dependent variables are those dimensional parameters required to
display the valve operator in the model that were not included in the P60A table.
45
Commodity Discussions
MC GS Term(G)_Rat(G) Term(R)_B
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are those dimensional
parameters required to display the component in the model that were not included in the P25A
table.
For piping valves whose operator types as defined in codelist set CL550, Operator/Actuator
Type, are less than or equal to 24, the empty weight of the valve, including the valve operator
weight, is included in a table with format P59. The name of this table is comprised of the
following parameter from the piping commodities part of the Piping Job Specification:
Cmdty Code
The only independent variable in this table is the nominal diameter of the green connect point
of the component. The only dependent variable is empty weight of the valve, including its
operator.
For piping valves whose operator types as defined in codelist set CL550, Operator/Actuator
Type, exceed 24 and are less than or equal to 40, the empty weight of the valve exclusive of
the operator weight, the operator weight, the model code for the valve operator, the three
parameters that define the location of the center of gravity of the operator and up to two
dimensional parameters required to define the geometry of the valve operator is included in a
table with format P60A. The name of this table is comprised of the following parameter from
the piping commodities part of the Piping Job Specification:
Cmdty Code_WOPD_A
The only independent variable in this table is the nominal diameter of the green connect point
of the component. The dependent variables are the empty weight of the valve exclusive of
the operator weight, the operator weight, the model code of the operator, the three
parameters that define the location of the center of gravity of the operator and up to two
dimensional parameters required to define the geometry of the valve operator.
If columns available in the above table were insufficient to allow definition of all the applicable
dimensional parameters of the valve operator, the remaining parameters are included in a
table with format P60B. The name of the P60B table is comprised of the following parameter
from the piping commodities part of the Piping Job Specification:
Cmdty Code_WOPD_B
The only independent variable in this table is the nominal diameter of the green connect point
of the component. The dependent variables are those dimensional parameters required to
display the valve operator in the model that were not included in the P60A table.
Green and Red Connect Point Data, GCP Male, RCP Male
If both green and red connect point data appear in the definition of the component in the Piping
Job Specification and if the neither the green nor the red connect points are a male termination
type, the following applies:
General data about the component is included in a table with format P26A. The name of this
table is comprised of the following parameters from the piping commodities part of the Piping
Job Specification:
MC GS Term(G)_Rat(G) Term(R)_Rat(R) A
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are surface area, weight of water
plus all those dimensional parameters required to display the component in the model whose
values are not defined in a generic table.
If columns available in the above table were insufficient to allow definition of all the applicable
dimensional parameters, the remaining parameters are included in a table with format P26B.
46
Commodity Discussions
The name of the P26B table is comprised of the following parameters from the piping
commodities part of the Piping Job Specification:
MC GS Term(G)_Rat(G) Term(R)_Rat(R) B
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are those dimensional
parameters required to display the component in the model that were not included in the P26A
table.
For piping valves whose operator types as defined in codelist set CL550, Operator/Actuator
Type, are less than or equal to 24, the empty weight of the valve, including the valve operator
weight, is included in a table with format P59. The name of this table is comprised of the
following parameter from the piping commodities part of the Piping Job Specification:
Cmdty Code
The only independent variable in this table is the nominal diameter of the green connect point
of the component. The only dependent variable is empty weight of the valve, including its
operator.
For piping valves whose operator types as defined in codelist set CL550, Operator/Actuator
Type, exceed 24 and are less than or equal to 40, the empty weight of the valve exclusive of
the operator weight, the operator weight, the model code for the valve operator, the three
parameters that define the location of the center of gravity of the operator and up to two
dimensional parameters required to define the geometry of the valve operator is included in a
table with format P60A. The name of this table is comprised of the following parameter from
the piping commodities part of the Piping Job Specification:
Cmdty Code_WOPD_A
The only independent variable in this table is the nominal diameter of the green connect point
of the component. The dependent variables are the empty weight of the valve exclusive of
the operator weight, the operator weight, the model code of the operator, the three
parameters that define the location of the center of gravity of the operator and up to two
dimensional parameters required to define the geometry of the valve operator.
If columns available in the above table were insufficient to allow definition of all the applicable
dimensional parameters of the valve operator, the remaining parameters are included in a
table with format P60B. The name of the P60B table is comprised of the following parameter
from the piping commodities part of the Piping Job Specification:
Cmdty Code_WOPD_B
The only independent variable in this table is the nominal diameter of the green connect point
of the component. The dependent variables are those dimensional parameters required to
display the valve operator in the model that were not included in the P60A table.
47
Commodity Discussions
If columns available in the above table were insufficient to allow definition of all the applicable
dimensional parameters, the remaining parameters are included in a table with format P26B.
The name of the P26B table is comprised of the following parameters from the piping
commodities part of the Piping Job Specification:
MC_GS_Term(G) Rat(G) Term(R) Rat(R) B
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are those dimensional
parameters required to display the component in the model that were not included in the P26A
table.
For piping valves whose operator types as defined in codelist set CL550, Operator/Actuator
Type, are less than or equal to 24, the empty weight of the valve, including the valve operator
weight, is included in a table with format P59. The name of this table is comprised of the
following parameter from the piping commodities part of the Piping Job Specification:
Cmdty Code
The only independent variable in this table is the nominal diameter of the green connect point
of the component. The only dependent variable is empty weight of the valve, including its
operator.
For piping valves whose operator types as defined in codelist set CL550, Operator/Actuator
Type, exceed 24 and are less than or equal to 40, the empty weight of the valve exclusive of
the operator weight, the operator weight, the model code for the valve operator, the three
parameters that define the location of the center of gravity of the operator and up to two
dimensional parameters required to define the geometry of the valve operator is included in a
table with format P60A.The name of this table is comprised of the following parameter from the
piping commodities part of the Piping Job Specification:
Cmdty Code_WOPD_A
The only independent variable in this table is the nominal diameter of the green connect point
of the component. The dependent variables are the empty weight of the valve exclusive of
the operator weight, the operator weight, the model code of the operator, the three
parameters that define the location of the center of gravity of the operator and up to two
dimensional parameters required to define the geometry of the valve operator.
If columns available in the above table were insufficient to allow definition of all the applicable
dimensional parameters of the valve operator, the remaining parameters are included in a
table with format P60B. The name of the P60B table is comprised of the following parameter
from the piping commodities part of the Piping Job Specification:
Cmdty Code_WOPD_B
The only independent variable in this table is the nominal diameter of the green connect point
of the component. The dependent variables are those dimensional parameters required to
display the valve operator in the model that were not included in the P60A table.
Green and Red Connect Point Data, GCP = Male, RCP Male
If both green and red connect point data appear in the definition of the component in the Piping
Job Specification, the green connect point is a male termination type and the red connect point is
not a male termination type, the following applies:
General data about the component is included in a table with format P27A. The name of this
table is comprised of the following parameters from the piping commodities part of the Piping
Job Specification:
MC_GS_Term(G) Term(R) Rat(R) A
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are surface area, weight of water
48
Commodity Discussions
plus all those dimensional parameters required to display the component in the model whose
values are not defined in a generic table.
If columns available in the above table were insufficient to allow definition of all the applicable
dimensional parameters, the remaining parameters are included in a table with format P27B.
The name of the P27B table is comprised of the following parameters from the piping
commodities part of the Piping Job Specification:
MC_GS_Term(G) Term(R) Rat(R) B
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are those dimensional parameters
required to display the component in the model that were not included in the P27A table.
For piping valves whose operator types as defined in codelist set CL550, Operator/Actuator
Type, are less than or equal to 24, the empty weight of the valve, including the valve operator
weight, is included in a table with format P59. The name of this table is comprised of the
following parameter from the piping commodities part of the Piping Job Specification:
Cmdty Code
The only independent variable in this table is the nominal diameter of the green connect point
of the component. The only dependent variable is empty weight of the valve, including its
operator.
For piping valves whose operator types as defined in codelist set CL550, Operator/Actuator
Type, exceed 24 and are less than or equal to 40, the empty weight of the valve exclusive of
the operator weight, the operator weight, the model code for the valve operator, the three
parameters that define the location of the center of gravity of the operator and up to two
dimensional parameters required to define the geometry of the valve operator is included in a
table with format P60A. The name of this table is comprised of the following parameter from
the piping commodities part of the Piping Job Specification:
Cmdty Code_WOPD_A
The only independent variable in this table is the nominal diameter of the green connect point
of the component. The dependent variables are the empty weight of the valve exclusive of
the operator weight, the operator weight, the model code of the operator, the three
parameters that define the location of the center of gravity of the operator and up to two
dimensional parameters required to define the geometry of the valve operator.
If columns available in the above table were insufficient to allow definition of all the applicable
dimensional parameters of the valve operator, the remaining parameters are included in a
table with format P60B. The name of the P60B table is comprised of the following parameter
from the piping commodities part of the Piping Job Specification:
Cmdty Code_WOPD_B
The only independent variable in this table is the nominal diameter of the green connect point
of the component. The dependent variables are those dimensional parameters required to
display the valve operator in the model that were not included in the P60A table.
Unless otherwise indicated, all valves have operators. Refer to paragraph C.6.1 for
additional requirements regarding operators.
Valves and their operators are not placed during automatic component placement. They
must be positioned manually.
For the table format descriptions applicable to each component type, the GCP and RCP rating
and schedule/thickness that needs to be provided in the Piping Job Specification has been
listed. These values are required for one or more of the reasons indicated below and are not
necessarily part of the names of the tables that include data about the component.
To procure the component.
49
Commodity Discussions
To access data tables. Refer to Section 4, Model Graphics Definitions, for a description of the
table formats.
To supply data required for stress analysis purposes.
50
Commodity Discussions
TNF=P15A, P31A & P59, or
P15A, P60A & P60B
Beveled ends
For GCP: Rating="Value"; Sc/Th="Value"
For RCP: Rating="-"; Sc/Th="-"
Regular pattern, female ends, full port gate valve (MC=GATF)
(SN=V1)
TNF=P15A, P31A & P59
Socket ends
Socketwelded ends
Female threaded ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="-"; Sc/Th="-"
TNF=P26A, P31A & P59
Socketwelded/female threaded ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="Value"; Sc/Th="NREQD"
Regular pattern, female ends, reduced port gate valve
(MC=GATR) (SN=V1)
TNF=P15A, P31A & P59
Socket ends
Socketwelded ends
Female threaded ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="-"; Sc/Th="-"
TNF=P26A, P31A & P59
Socketwelded/female threaded ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="Value"; Sc/Th="NREQD"
51
Commodity Discussions
TNF=P27A, P31A & P59
Beveled/socketwelded ends
Beveled/female threaded ends
For GCP: Rating="Value"; Sc/Th="Value"
For RCP: Rating="Value"; Sc/Th="NREQD"
Extended body gate valve (no iso operator) (MC=GATXBA) (SN=V2A)
This is used to place an olet valve similarly to a branch
component. Since this symbol is mapped in Isogen to one
derived from an olet type branch component, it is not
possible to place an iso operator on it.
TNF=P27A, P31A & P59
Olet/socketwelded ends
Olet/female threaded ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="Value"; Sc/Th="NREQD"
Extended body gate valve (MC=GATXBB) (SN=V2B)
This is used to place an olet valve at a tap, for example at a cap.
TNF=P27A, P31A & P59
Olet/socketwelded ends
Olet/female threaded ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="Value"; Sc/Th="NREQD"
52
Commodity Discussions
TNF=P15A & P59
Beveled ends
For GCP: Rating="Value"; Sc/Th="Value"
For RCP: Rating="-"; Sc/Th="-"
53
Commodity Discussions
TNF=P15A, P31A & P59, or
P15A, P60A & P60B
Beveled ends
For GCP: Rating="Value"; Sc/Th="Value"
For RCP: Rating="-"; Sc/Th="-"
Long pattern, bolted or male ends ball valve (MC=BALLP) (SN=V6)
TNF=P15A, P31A & P59, or
P15A, P60A & P60B
Flanged ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="-"; Sc/Th="-"
TNF=P25A, P31A & P59, or
P25A, P60A & P60B
Flanged/beveled ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="-"; Sc/Th="Value"
TNF=P15A, P31A & P59, or
P15A, P60A & P60B
Beveled ends
For GCP: Rating="Value"; Sc/Th="Value"
For RCP: Rating="-"; Sc/Th="-"
Venturi pattern, bolted or male ends ball valve (MC=BALVP) (SN=V6)
TNF=P15A, P31A & P59, or
P15A, P60A & P60B
Flanged ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="-"; Sc/Th="-"
TNF=P25A, P31A & P59, or
P25A, P60A & P60B
Flanged/beveled ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="-"; Sc/Th="Value"
TNF=P15A, P31A & P59, or
P15A, P60A & P60B
Beveled ends
For GCP: Rating="Value"; Sc/Th="Value"
For RCP: Rating="-"; Sc/Th="-"
54
Commodity Discussions
TNF=P15A, P31A & P59, or
P15A, P60A & P60B
Flanged ends
Socket ends
Socketwelded ends
Female threaded ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="-"; Sc/Th="-"
TNF=P15A, P31A & P59, or
P15A, P60A & P60B
Beveled ends
For GCP: Rating="Value"; Sc/Th="Value"
For RCP: Rating="-"; Sc/Th="-"
55
Commodity Discussions
TNF=P15A, P31A & P59
Socket ends
Socketwelded ends
Female threaded ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="-"; Sc/Th="-"
TNF=P26A, P31A & P59
Socketwelded/female threaded ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="Value"; Sc/Th="NREQD"
Regular pattern, female ends, reduced port globe valve
(MC=GLOR) (SN=V11)
TNF=P15A, P31A & P59
Socket ends
Socketwelded ends
Female threaded ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="-"; Sc/Th="-"
TNF=P26A, P31A & P59
Socketwelded/female threaded ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="Value"; Sc/Th="NREQD"
56
Commodity Discussions
TNF=P15A, P31A & P59, or
P15A, P60A & P60B
Beveled ends
For GCP: Rating="Value"; Sc/Th="Value"
For RCP: Rating="-"; Sc/Th="-"
57
Commodity Discussions
The graphics for the valve operator will distinguish a Y
globe valve from a globe valve.
58
Commodity Discussions
TNF=P15A, P31A & P59, or
P15A, P60A & P60B
Flanged ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="-"; Sc/Th="-"
TNF=P15A, P31A & P59, or
P15A, P60A & P60B
Mechanical joint ends
For GCP: Rating="Value"; Sc/Th="NREQD" or "Value"
For RCP: Rating="-"; Sc/Th="-"
TNF=P25A, P31A & P59, or
P25A, P60A & P60B
Flanged/beveled ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="-"; Sc/Th="Value"
Bolted or male ends, full port and round bore plug valve
(MC=PLUFB) (SN=V16)
TNF=P15A, P31A & P59, or
P15A, P60A & P60B
Flanged ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="-"; Sc/Th="-"
TNF=P15A, P31A & P59, or
P15A, P60A & P60B
Mechanical joint ends
For GCP: Rating="Value"; Sc/Th="NREQD" or "Value"
For RCP: Rating="-"; Sc/Th="-"
TNF=P25A, P31A & P59, or
P25A, P60A & P60B
Flanged/beveled ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="-"; Sc/Th="Value"
Female ends, full port plug valve (MC=PLUF) (SN=V16)
TNF=P15A, P31A & P59
Socket ends
Socketwelded ends
Female threaded ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="-"; Sc/Th="-"
Female ends, reduced port plug valve (MC=PLUR) (SN=V16)
59
Commodity Discussions
TNF=P15A, P31A & P59
Socket ends
Socketwelded ends
Female threaded ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="-"; Sc/Th="-"
60
Commodity Discussions
TNF=P15A, P31A & P59, or
P15A, P60A & P60B
Flanged ends
Thru-bolted ends
Thru-bolted ends with integral gaskets
Thru-bolted with cap-screw ends
Thru-bolted with cap-screw ends with integral gaskets
Male grooved ends
Mechanical joint bell ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="-"; Sc/Th="-"
High pressure butterfly valve (MC=BFYHP) (SN=V26)
TNF=P15A, P31A & P59, or
P15A, P60A & P60B
Flanged ends
Thru-bolted ends
Thru-bolted ends with integral gaskets
Thru-bolted with cap-screw ends
Thru-bolted with cap-screw ends with integral gaskets
Male grooved ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="-"; Sc/Th="-"
61
Commodity Discussions
Plastic lined diaphragm valve (MC=DIAPL) (SN=V1)
TNF=P15A, P31A & P59, or
P15A, P60A & P60B
Flanged ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="-"; Sc/Th="-"
Glass lined diaphragm valve (MC=DIAGL) (SN=V1)
TNF=P15A, P31A & P59, or
P15A, P60A & P60B
Flanged ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="-"; Sc/Th="-"
62
Commodity Discussions
TNF=P15A, P31A & P59, or
P15A, P60A & P60B
Beveled ends
For GCP: Rating="Value"; Sc/Th="Value"
For RCP: Rating="-"; Sc/Th="-"
TNF=P26A, P31A & P59, or
P26A, P60A & P60B
Beveled/beveled ends
For GCP: Rating="Value"; Sc/Th="Value"
For RCP: Rating="-"; Sc/Th="Value"
This type of component is used to represent "simple"
slide valves from catalog data. Slide valves for FCCU
service is defined as control valves.
63
Commodity Discussions
64
Commodity Discussions
Long pattern, female ends, full port lift check valve (no
operator) (MC=CKLF) (SN=V38)
TNF=P15A & P59
Socket ends
Socketwelded ends
Female threaded ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="-"; Sc/Th="-"
TNF=P26A & P59
Socketwelded/female threaded ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="Value"; Sc/Th="NREQD"
Regular pattern, female ends, reduced port lift check valve
(no operator) (MC=CKLR) (SN=V38)
TNF=P15A & P59
Socket ends
Socketwelded ends
Female threaded ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="-"; Sc/Th="-"
TNF=P26A & P59
Socketwelded/female threaded ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="Value"; Sc/Th="NREQD"
Long pattern, bolted or male ends swing check valve (no
operator) (MC=CKS) (SN=V38)
TNF=P15A & P59
Flanged ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="-"; Sc/Th="-"
TNF=P15A & P59
Mechanical joint ends
For GCP: Rating="Value"; Sc/Th="NREQD" or "Value"
For RCP: Rating="-"; Sc/Th="-"
TNF=P15A & P59
Beveled ends
For GCP: Rating="Value"; Sc/Th="Value"
For RCP: Rating="-"; Sc/Th="-"
TNF=P15A & P59
Male grooved ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="-"; Sc/Th="-"
Regular pattern, female ends, full port swing check valve
(no operator) (MC=CKSF) (SN=V38)
TNF=P15A & P59
Socket ends
Socketwelded ends
Female threaded ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="-"; Sc/Th="-"
65
Commodity Discussions
TNF=P26A & P59
Socketwelded/female threaded ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="Value"; Sc/Th="NREQD"
Regular pattern, female ends, reduced port swing check valve
(no operator) (MC=CKSR) (SN=V38)
TNF=P15A & P59
Socket ends
Socketwelded ends
Female threaded ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="-"; Sc/Th="-"
TNF=P26A & P59
Socketwelded/female threaded ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="Value"; Sc/Th="NREQD"
Regular pattern, Y-swing check valve (no operator) (MC=CKSY)
(SN=V38)
TNF=P15A & P59
Flanged ends
Socket ends
Socketwelded ends
Female threaded ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="-"; Sc/Th="-"
TNF=P15A & P59
Mechanical joint ends
For GCP: Rating="Value"; Sc/Th="NREQD" or "Value"
For RCP: Rating="-"; Sc/Th="-"
TNF=P15A & P59
Beveled ends
For GCP: Rating="Value"; Sc/Th="Value"
For RCP: Rating="-"; Sc/Th="-"
TNF=P15A & P59
Male grooved ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="-"; Sc/Th="-"
TNF=P26A & P59
Socketwelded/female threaded ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="Value"; Sc/Th="NREQD"
Regular pattern, female ends, Y reduced port lift check
valve (no operator) (MC=CKLRY) (SN=V38)
TNF=P15A & P59
Socket ends
Socketwelded ends
Female threaded ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="-"; Sc/Th="-"
66
Commodity Discussions
TNF=P26A & P59
Socketwelded/female threaded ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="Value"; Sc/Th="NREQD"
67
Commodity Discussions
TNF=P15A & P59
Beveled ends
For GCP: Rating="Value"; Sc/Th="Value"
For RCP: Rating="-"; Sc/Th="-"
68
Commodity Discussions
TNF=P15A, P31A & P59, or
P15A, P60A & P60B
Flanged ends
Socketwelded ends
Female threaded ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="-"; Sc/Th="-"
TNF=P15A, P31A & P59, or
P15A, P60A & P60B
Beveled ends
For GCP: Rating="Value"; Sc/Th="Value"
For RCP: Rating="-"; Sc/Th="-"
69
Commodity Discussions
TNF=P15A, P31A & P59, or
P15A, P60A & P60B
Beveled ends
For GCP: Rating="Value"; Sc/Th="Value"
For RCP: Rating="-"; Sc/Th="-"
70
Commodity Discussions
71
Commodity Discussions
72
Commodity Discussions
73
Commodity Discussions
See Also
Connect Point Data_GCP (on page 75)
6Q2C01, Flange (in-line) (on page 80)
6Q2C03, Reducing flange (in-line) (not-automatic) (on page 83)
6Q2C04, Expander flange (in-line) (not-automatic) (on page 84)
6Q2C06, Orifice flange (in-line) (not-automatic) (on page 84)
6Q2C08, Blind flange (in-line) (not-automatic) (on page 86)
6Q2C10, Open spectacle blank (in-line) (not-automatic) (on page 87)
6Q2C11, Closed spectacle blank (in-line) (not-automatic) (on page 87)
6Q2C12, Blank disc (in-line) (not-automatic) (on page 87)
6Q2C13, Blind spacer (in-line) (not-automatic) (on page 87)
6Q2C14, Tapered spacer (in-line) (not-automatic) (on page 87)
6Q2C15, Open spacer (in-line) (not-automatic) (on page 88)
6Q2C16, End (in-line) (not-automatic) (on page 88)
6Q2C17, Head (in-line) (not-automatic) (on page 88)
6Q2C19, Plug (in-line) (not-automatic) (on page 89)
6Q2C21, Cap (in-line) (not-automatic) (on page 89)
6Q2C23, Concentric diameter change (in-line) (on page 89)
6Q2C24, Eccentric diameter change (in-line) (not-automatic) (on page 89)
6Q2C25, Coupling-connector (in-line) (not-automatic) (on page 89)
6Q2C26, Half coupling (in-line) (not-automatic) (on page 90)
6Q2C27, Concentric reducer (in-line) (on page 91)
6Q2C28, Eccentric reducer (in-line) (not-automatic) (on page 92)
6Q2C32, Reducing coupling (in-line) (not-automatic) (on page 92)
6Q2C35, Concentric swage (in-line) (on page 93)
6Q2C36, Eccentric swage (in-line) (not-automatic) (on page 93)
6Q2C39, Union (in-line) (not-automatic) (on page 94)
6Q2C40, Orifice union (in-line) (not-automatic) (on page 94)
6Q2C41, Dielectric union (in-line) (not-automatic) (on page 94)
6Q2C43, Hose connection (in-line) (not-automatic) (on page 94)
6Q2C44, Bushing (in-line) (not-automatic) (on page 95)
6Q2C46, Reducing insert (in-line) (not-automatic) (on page 95)
6Q2C47, Pipe bend (in-line) (on page 95)
6Q2C49, 5.625 deg elbow (in-line) (not-automatic) (on page 96)
6Q2C51, 11.25 deg elbow (in-line) (not-automatic) (on page 96)
6Q2C53, 22.5 deg elbow (in-line) (not-automatic) (on page 97)
6Q2C55, <45 deg direction change (in-line) (on page 97)
6Q2C56, 45 deg direction change (in-line) (on page 98)
6Q2C57, 45 deg elbow (in-line) (on page 98)
6Q2C59, 45 deg LR elbow (in-line) (on page 99)
6Q2C60, 45 deg long tangent elbow (in-line) (on page 99)
6Q2C61, 45 deg 3D elbow (in-line) (on page 100)
6Q2C63, 45 deg union elbow (in-line) (not-automatic) (on page 100)
6Q2C65, 45 deg street elbow (in-line) (not-automatic) (on page 100)
74
Commodity Discussions
6Q2C66, 45 deg short elbow (in-line) (on page 101)
6Q2C68, 45 deg long elbow (in-line) (on page 101)
6Q2C73, 60 deg elbow (in-line) (not-automatic) (on page 101)
6Q2C75, 45-90 deg direction change (in-line) (on page 101)
6Q2C76, 90 deg direction change (in-line) (on page 102)
6Q2C77, 90 deg elbow (in-line) (on page 102)
6Q2C79, 90 deg SR elbow (in-line) (on page 103)
6Q2C80, 90 deg LR elbow (in-line) (on page 103)
6Q2C82, 90 deg LR long tangent elbow (in-line) (on page 104)
6Q2C84, 90 deg reducing elbow (in-line) (on page 104)
6Q2C86, 90 deg 3D elbow (in-line) (on page 104)
6Q2C88, 90 deg union elbow (in-line) (not-automatic) (on page 105)
6Q2C90, 90 deg street elbow (in-line) (not-automatic) (on page 105)
6Q2C91, 90 deg reducing street elbow (in-line) (not-automatic) (on page 105)
6Q2C93, 90 deg short elbow (in-line) (on page 106)
6Q2C94, 90 deg long elbow (in-line) (on page 106)
The only independent variable in this table is the nominal diameter of the green connect point
of the component. The dependent variables are those dimensional parameters required to
display the component in the model that were not included in the P11A table.
The empty weight of the component is included in a table with format P51. The name of this
table is comprised of the following parameters from the piping commodities part of the Piping
Job Specification:
MC GS Term(G)_Sc/Th(G)_WC
The only independent variable in this table is the nominal diameter of the green connect point
of the component. The only dependent variable is empty weight of the component.
75
Commodity Discussions
Green Connect Point Data Only, GCP Male
If only green connect point data appears in the definition of the component in the Piping Job
Specification and if the connect point is not a male termination type, the following applies:
General data about the component is included in a table with format P15A. The name of this
table is comprised of the following parameters from the piping commodities part of the Piping
Job Specification:
MC GS Term(G) Rat(G) A
The only independent variable in this table is the nominal diameter of the green connect point
of the component. The dependent variables are surface area, weight of water plus all those
dimensional parameters required to display the component in the model whose values are not
defined in a generic table.
If columns available in the above table were insufficient to allow definition of all the applicable
dimensional parameters, the remaining parameters are included in a table with format P15B.
The name of the P15B table is comprised of the following parameters from the piping
commodities part of the Piping Job Specification:
MC GS Term(G) Rat(G) B
The only independent variable in this table is the nominal diameter of the green connect point
of the component. The dependent variables are those dimensional parameters required to
display the component in the model that were not included in the P15A table.
The empty weight of the component is included in a table with format P52. The name of this
table is comprised of the following parameters from the piping commodities part of the Piping
Job Specification:
MC GS Term(G)_Rat(G) Sc/Th(G)_WC
The only independent variable in this table is the nominal diameter of the green connect point
of the component. The only dependent variable is empty weight of the component.
76
Commodity Discussions
The empty weight of the component is included in a table with format P61. The name of this
table is comprised of the following parameters from the piping commodities part of the Piping
Job Specification:
MC GS Term(G)_Rat(G) Term(R)_Rat/Sc/Th(R)_WC
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The only dependent variable is empty weight of the
component.
Green and Red Connect Point Data, GCP Male, RCP Male
If both green and red connect point data appear in the definition of the component in the piping
commodities part of the Piping Job Specification and neither the green nor the "red" connect
points are male termination types, the following applies:
General data about the component is included in a table with format P26A. The name of this
table is comprised of the following parameters from the piping commodities part of the Piping
Job Specification:
MC GS Term(G)_Rat(G) Term(R)_Rat(R) A
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are surface area, weight of water
plus all those dimensional parameters required to display the component in the model whose
values are not defined in a generic table.
If columns available in the above table were insufficient to allow definition of all the applicable
dimensional parameters, the remaining parameters are included in a table with format P26B.
The name of the P26B table is comprised of the following parameters from the piping
commodities part of the Piping Job Specification:
MC GS Term(G)_Rat(G) Term(R)_Rat(R) B
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are those dimensional
parameters required to display the component in the model that were not included in the P26A
table.
The empty weight of the component is included in a table with format P62. The name of this
table is comprised of the following parameters from the piping commodities part of the Piping
Job Specification:
MC_GS_Term(G) Rat(G) Term(R) Rat(R) Sc/Th(R)_WC
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The only dependent variable is empty weight of the
component.
Green and Red Connect Point Data, GCP=Male, RCP=Male, MC WOL, SOL, TOL, NOL,
EOL, LOL, RPAD* or RWELD*
If both green and red connect point data appear in the definition of the component in the Piping
Job Specification and both the green and red connect points are male termination type and the
model code is not WOL, SOL, TOL, NOL, EOL, LOL, RPAD* or RWELD*, the following applies:
General data about the component is included in a table with format P21A. The name of this
table is comprised of the following parameters from the piping commodities part of the Piping
Job Specification:
MC GS Term(G) Term(R) A
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are surface area, weight of water
77
Commodity Discussions
plus all those dimensional parameters required to display the component in the model whose
values are not defined in a generic table.
If columns available in the above table were insufficient to allow definition of all the applicable
dimensional parameters, the remaining parameters are included in a table with format P21B.
The name of the P21B table is comprised of the following parameters from the piping
commodities part of the Piping Job Specification:
MC GS Term(G) Term(R) B
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are those dimensional
parameters required to display the component in the model that were not included in the P21A
table.
The empty weight of the component is included in a table with format P63. The name of this
table is comprised of the following parameters from the piping commodities part of the Piping
Job Specification:
MC_GS_Term(G) Sc/Th(G) Term(R) Sc/Th(R)_WC
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The only dependent variable is empty weight of the
component.
Green and Red Connect Point Data, GCP=Male, RCP Male, MC WOL, SOL, TOL, NOL,
EOL LOL, RPAD* or RWELD*
If both green and red connect point data appear in the definition of the component in the Piping
Job Specification, the green connect point is a male termination type, the red connect point is not
a male termination type and the model code is not WOL, SOL, TOL, NOL, EOL LOL, RPAD* or
RWELD*, the following applies:
General data about the component is included in a table with format P27A. The name of this
table is comprised of the following parameters from the piping commodities part of the Piping
Job Specification:
MC_GS_Term(G) Term(R) Rat(R) A
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are surface area, weight of water
plus all those dimensional parameters required to display the component in the model whose
values are not defined in a generic table.
If columns available in the above table were insufficient to allow definition of all the applicable
dimensional parameters, the remaining parameters are included in a table with format P27B.
The name of the P27B table is comprised of the following parameters from the piping
commodities part of the Piping Job Specification:
MC_GS_Term(G) Term(R) Rat(R) B
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are those dimensional
parameters required to display the component in the model that were not included in the P27A
table.
The empty weight of the component is included in a table with format P64. The name of this
table is comprised of the following parameters from the piping commodities part of the Piping
Job Specification:
MC_GS_Term(G) Sc/Th(G) Term(R) Rat(R)_WC
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The only dependent variable is empty weight of the
component.
78
Commodity Discussions
Green and Red Connect Point Data, GCP=Male, RCP=Male or Female, MC=WOL, SOL, TOL,
NOL, EOL or LOL
If both green and red connect point data appear in the definition of the component in the Piping
Job Specification, the green connect point is a male termination type, the red connect point is
either a male or a female termination type and the model code is WOL, SOL, TOL, NOL, EOL or
LOL, the following applies:
General data about the component is included in a table with format P28A. The name of this
table is comprised of the following parameters from the piping commodities part of the Piping
Job Specification:
MC_GS_Term(G) Sc/Th(G) Term(R) Rat/Sc/Th(R) A
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are surface area, weight of water
plus all those dimensional parameters required to display the component in the model whose
values are not defined in a generic table.
If columns available in the above table were insufficient to allow definition of all the applicable
dimensional parameters, the remaining parameters are included in a table with format P28B.
The name of the P28B table is comprised of the following parameters from the piping
commodities part of the Piping Job Specification:
MC_GS_Term(G) Sc/Th(G) Term(R) Rat/Sc/Th(R) B
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are those dimensional
parameters required to display the component in the model that were not included in the P28A
table.
The empty weight of the component is included in a table with format P65. The name of this
table is comprised of the following parameters from the piping commodities part of the Piping
Job Specification:
MC_GS_Term(G) Sc/Th(G) Term(R) Rat/Sc/Th(R)_WC
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The only dependent variable is empty weight of the
component.
Green and Red Connect Point Data, GCP=Male, RCP=Male, MC=RPAD*, RWELD*
If both green and red connect point data appear in the definition of the component in the Piping
Job Specification and both the green and the red connect points are male termination types and
the model code is RPAD* or RWELD*, the following applies:
General data about the component is included in a table with format P29A. The name of this
table is comprised of the following parameters:
MC_GS_BrchTbl Angle A
79
Commodity Discussions
80
Commodity Discussions
TNF=P25A & P61
Flanged/beveled ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="Value"; Sc/Th="Value"
Short-stub-end, lap joint flange (MC=FSSL) (SN=F1A)
TNF=P25A & P61
Flanged/beveled ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="Value"; Sc/Th="Value"
Short-stub-end, plate flange (MC=FSSPL) (SN=F1A)
TNF=P25A & P61
Flanged/beveled ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="Value"; Sc/Th="Value"
Long-stub-end, slip-on flange (MC=FLSSO) (SN=F1A)
TNF=P25A & P61
Flanged/beveled ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="Value"; Sc/Th="Value"
Long-stub-end, lap joint flange (MC=FLSL) (SN=F1A)
TNF=P25A & P61
Flanged/beveled ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="Value"; Sc/Th="Value"
Filler flange (MC=FFIL) (SN=F1A)
TNF=P15A & P52
Flanged ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="-"; Sc/Th="-"
Socket flange (MC=FS) (SN=F1A)
TNF=P26A & P62
Flanged/socket ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="Value"; Sc/Th="Value"
Socketwelded flange (MC=FSW) (SN=F1A)
TNF=P26A & P62
Flanged/socketwelded ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="Value"; Sc/Th="Value"
81
Commodity Discussions
Threaded flange (MC=FTHD) (SN=F1A)
TNF=P26A & P62
Flanged/female threaded ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="Value"; Sc/Th="NREQD"
Flanged connecting piece (MC=FCP) (SN=F1A)
TNF=P25A & P61
Flanged/plain ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="Value"; Sc/Th="Value"
The following comments apply to the above items:
o The "rating" for the RCP, if applicable, is the same
as for the flange itself, regardless of the CP preparation
involved. A value is provided in the "rating" field
to minimize the number of weight tables required to define
these components.
o For flanges placed together with stub-ends, the flange
is defined in the piping materials class as the
primary component. The stub-end is defined as its
implied component, using the "*" prefix method.
o Prior to the automatic placement of flanges, all
user-placed components that have flanged ends must be
placed in the model. During automatic placement of
flanges, the system will determine whether the flange
being placed shares the CP preparation, CP rating and
table suffix of its previously placed mate. If it does,
the flange being placed is accepted; if it does not,
the system will search for the next occurrence of the
AABBCC code. The checking process is repeated until
a match is found. If a match is not found, error message
GMXXX is returned.
o During automatic component placement, the piping software
will refuse to attach slip-on or lap-joint flanges without
stub-ends to any kind of fitting. Only attachment of a
slip-on or lap-joint flange to a plain section of pipe
is allowed. For piping materials classes with
slip-on or lap-joint flanges, two flanges are defined:
a first one that will lead to a slip-on or lap-joint
flange; a second one that will lead to an acceptable
flange type for attachment to a fitting. If during
automatic component placement, the system refuses to
attach the first flange selected because of the above
criteria, a new search is made in the piping
materials class for the second flange.
82
Commodity Discussions
83
Commodity Discussions
84
Commodity Discussions
TNF=P25A & P61
Flanged/plain ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="Value"; Sc/Th="NREQD"
Slip-on orifice flange w/0.5inch socketwelded taps
(MC=FOSOAW) (SN=F6)
TNF=P25A & P61
Flanged/plain ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="Value"; Sc/Th="NREQD"
Slip-on orifice flange w/0.75inch threaded taps (MC=FOSOB)
(SN=F6)
TNF=P25A & P61
Flanged/plain ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="Value"; Sc/Th="NREQD"
Slip-on orifice flange w/0.75inch socketwelded taps
(MC=FOSOBW) (SN=F6)
TNF=P25A & P61
Flanged/plain ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="Value"; Sc/Th="NREQD"
Socketwelded orifice flange w/0.5inch threaded taps
(MC=FOSWA) (SN=F6)
TNF=P26A & P62
Flanged/socketwelded ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="Value"; Sc/Th="Value"
Socketwelded orifice flange w/0.5inch socketwelded taps
(MC=FOSWAW) (SN=F6)
TNF=P26A & P62
Flanged/socketwelded ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="Value"; Sc/Th="Value"
Socketwelded orifice flange w/0.75inch threaded taps
(MC=FOSWB) (SN=F6)
TNF=P26A & P62
Flanged/socketwelded ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="Value"; Sc/Th="Value"
85
Commodity Discussions
Socketwelded orifice flange w/0.75inch socketwelded taps
(MC=FOSWBW) (SN=F6)
TNF=P26A & P62
Flanged/socketwelded ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="Value"; Sc/Th="Value"
Threaded orifice flange w/0.5 inch threaded taps (MC=FOTHDA)
(SN=F6)
TNF=P26A & P62
Flanged/female threaded ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="Value"; Sc/Th="NREQD"
The following comments apply to the above items:
o The tap connect point is placed a distance of one-half
the flange thickness from the face of the flange. This
distance may not be dimensionally correct per the industry
standards. The user must modify the Eden if exact
coordinates are required for tap locations.
o The "rating" for the RCP, if applicable, is the same
as for the flange itself, regardless of the CP preparation
involved. A value is provided in the "rating" field
to minimize the number of weight tables required to define
these components.
o The number of taps for orifice flanges, "1" or "2", will
be defined in the "Mod" column of the Piping Job
Specification. Only these values are acceptable.
o The "rating" for the taps is derived from the entry
in the applicable Taps Table with an option code of "1"
and having the tap size implied in the orifice flange
being placed.
86
Commodity Discussions
87
Commodity Discussions
TNF=P15A & P52
Thru-bolted ends
Thru-bolted ends with integral gaskets
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="-"; Sc/Th="-"
The included angle of tapered spacers is determined by
the system from data in the design file and is supplied
to the component definition without need of user
intervention.
88
Commodity Discussions
TNF=P11A & P51
Beveled end
For GCP: Rating="-"; Sc/Th="Value"
For RCP: Rating="-"; Sc/Th="-"
89
Commodity Discussions
TNF=P15A & P52
Mechanical joint ends
For GCP: Rating="Value"; Sc/Th="NREQD" or "Value"
For RCP: Rating="-"; Sc/Th="-"
TNF=P15A & P52
Female grooved ends
Push-on bell ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="-"; Sc/Th="-"
TNF=P15A & P52
Socket ends
Socketwelded ends
Female threaded ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="-"; Sc/Th="-"
TNF=P25A & P61
Flanged/plain ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="-"; Sc/Th="NREQD"
TNF=P25A & P61
Mechanical joint/plain ends
For GCP: Rating="Value"; Sc/Th="NREQD" or "Value"
For RCP: Rating="-"; Sc/Th="NREQD"
TNF=P25A & P61
Socket/male threaded ends
For GCP: Rating="Value"; Sc/Th="Value"
For RCP: Rating="-"; Sc/Th="NREQD"
TNF=P26A & P62
Socket/female threaded ends
For GCP: Rating="Value"; Sc/Th="Value"
For RCP: Rating="Value"; Sc/Th="NREQD"
90
Commodity Discussions
91
Commodity Discussions
TNF=P27A & P64
Spigot/push-on bell ends
Plain/mechanical joint bell ends
Plain/push-on bell ends
For GCP: Rating="-"; Sc/Th="NREQD"
For RCP: Rating="Value"; Sc/Th="NREQD"
A note is required on the iso to identify the end connection
sizes.
92
Commodity Discussions
93
Commodity Discussions
94
Commodity Discussions
95
Commodity Discussions
The radius of the pipe bend is defined in the "Mod"
column of the Piping Job Specification in terms of the
nominal diameter.
Dimension tables with TNF=P11A are required for all pipe
bends, regardless of their model code. In these tables, a
"-" is shown for the surface area and water weight
parameters since they are calculated by the software
using the information available for plain piping. For pipe
bends with model code PIPB, values are provided for
table parameters "P1" and "P2" to define the lengths of the
straight sections involved. For pipe bends with model code
PIPB2, dashes are provided for table parameters "P1" and
"P2" since no straight sections are involved. The use of
tables with TNF=51 will not be required for pipe bends since
their empty weights are calculated by the software
using the information available for plain piping.
96
Commodity Discussions
TNF=P11A & P51
Male grooved ends
For GCP: Rating="-"; Sc/Th="Value"
For RCP: Rating="-"; Sc/Th="-"
TNF=P27A & P64
Spigot/push-on bell ends
For GCP: Rating="-"; Sc/Th="NREQD"
For RCP: Rating="Value"; Sc/Th="NREQD"
97
Commodity Discussions
98
Commodity Discussions
TNF=P27A & P64
Plain/socket ends
For GCP: Rating="-"; Sc/Th="Value"
For RCP: Rating="Value"; Sc/Th="NREQD"
99
Commodity Discussions
100
Commodity Discussions
101
Commodity Discussions
102
Commodity Discussions
TNF=P27A & P64
Spigot/push-on bell ends
Plain/push-on bell ends
For GCP: Rating="-"; Sc/Th="NREQD"
For RCP: Rating="Value"; Sc/Th="NREQD"
TNF=P27A & P64
Plain/socket ends
For GCP: Rating="-"; Sc/Th="Value"
For RCP: Rating="Value"; Sc/Th="NREQD"
103
Commodity Discussions
104
Commodity Discussions
Model code E90T3D is trimmed by the software to the
angle defined in the design file between elements defining
the center line routing of the segment or, if center line
routes do not exist, to the angle defined at placement.
The system will use data tables for E903D; tables specific
to E90T3D will not be required.
105
Commodity Discussions
See Also
Connect Point Data_Independent Variables (on page 107)
6Q3C01, 180 deg return (in-line) (not-automatic) (on page 112)
6Q3C03, 180 deg SR return (in-line) (not-automatic) (on page 112)
6Q3C05, 180 deg LR return (in-line) (not-automatic) (on page 112)
6Q3C07, 180 deg close return (in-line) (not-automatic) (on page 112)
6Q3C08, 180 deg medium return (in-line) (not-automatic) (on page 113)
6Q3C09, 180 deg open return (in-line) (not-automatic) (on page 113)
6Q3C14, Miter (in-line) (not-automatic) (on page 113)
6Q3C16, 45 deg miter (in-line) (on page 114)
6Q3C18, 90 deg miter (in-line) (on page 115)
6Q3C22, Tee (in-line) (on page 116)
6Q3C24, Reducing branch tee (in-line) (on page 117)
6Q3C25, Reducing run and branch tee (in-line) (on page 119)
6Q3C27, On-run union tee (in-line) (not-automatic) (on page 119)
6Q3C28, On-branch union tee (in-line) (not-automatic) (on page 119)
6Q3C31, Street tee (in-line) (not-automatic) (on page 120)
6Q3C34, Reducing instrument tee (in-line) (not-automatic) (on page 120)
6Q3C36, Drip ring tee (in-line) (not-automatic) (on page 120)
6Q3C38, Basin tee (in-line) (on page 121)
6Q3C45, True Y (in-line) (not-automatic) (on page 121)
6Q3C47, Lateral (in-line) (on page 121)
6Q3C49, Reducing branch lateral (in-line) (on page 122)
6Q3C50, Reducing run and branch lateral (in-line) (on page 123)
106
Commodity Discussions
6Q3C52, 90 deg short Y-branch (in-line) (not-automatic) (on page 123)
6Q3C53, 90 deg reducing short Y-branch (in-line) (not-automatic) (on page 123)
6Q3C54, 90 deg long Y-branch (in-line) (not-automatic) (on page 123)
6Q3C55, 90 deg reducing long Y-branch (in-line) (not-automatic) (on page 124)
6Q3C60, Cross (in-line) (not-automatic) (on page 124)
6Q3C62, Reducing branches cross (in-line) (not-automatic) (on page 125)
6Q3C63, Reducing run and branches cross (in-line) (not-automatic) (on page 125)
6Q3C64, Basin cross (in-line) (not-automatic) (on page 126)
6Q3C70, Saddle (in-line) (on page 126)
6Q3C72, Sweepolet (in-line) (on page 126)
6Q3C73, Weldolet (in-line) (on page 127)
6Q3C74, Sockolet (in-line) (on page 127)
6Q3C75, Thredolet (in-line) (on page 128)
6Q3C76, Nippolet (in-line) (on page 128)
6Q3C77, Elbolet (in-line) (not-automatic) (on page 129)
6Q3C78, Latrolet (in-line) (not-automatic) (on page 129)
6Q3C79, Endolet (in-line) (not-automatic) (on page 130)
6Q3C80, Reinforcing pad (in-line) (on page 130)
6Q3C82, Reinforcing weld (in-line) (on page 132)
6Q3C84, Buttweld (in-line) (not-automatic) (on page 134)
6Q3C88, Branch nipple (in-line) (not-automatic) (on page 134)
6Q3C89, In-line nipple (in-line) (not-automatic) (on page 135)
6Q3C95, Gasket (on page 135)
6Q3C97, Stud (on page 137)
107
Commodity Discussions
The empty weight of the component is included in a table with format P51. The name of this
table is comprised of the following parameters from the piping commodities part of the Piping
Job Specification:
MC GS Term(G)_Sc/Th(G)_WC
The only independent variable in this table is the nominal diameter of the green connect point
of the component. The only dependent variable is empty weight of the component.
The only independent variable in this table is the nominal diameter of the green connect point
of the component. The dependent variables are those dimensional parameters required to
display the component in the model that were not included in the P15A table.
The empty weight of the component is included in a table with format P52. The name of this
table is comprised of the following parameters from the piping commodities part of the Piping
Job Specification:
MC GS Term(G)_Rat(G) Sc/Th(G)_WC
The only independent variable in this table is the nominal diameter of the green connect point
of the component. The only dependent variable is empty weight of the component.
108
Commodity Discussions
The name of the P25B table is comprised of the following parameters from the piping
commodities part of the Piping Job Specification:
MC GS Term(G)_Rat(G) Term(R)_B
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are those dimensional
parameters required to display the component in the model that were not included in the P25A
table.
The empty weight of the component is included in a table with format P61. The name of this
table is comprised of the following parameters from the piping commodities part of the Piping
Job Specification:
MC GS Term(G)_Rat(G) Term(R)_Sc/Th(R)_WC
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The only dependent variable is empty weight of the
component.
Green and Red Connect Point Data, GCP Male, RCP Male
If both green and red connect point data appear in the definition of the component in the Piping
Job Specification and neither the green nor the red connect points are male termination types, the
following applies:
General data about the component is included in a table with format P26A. The name of this
table is comprised of the following parameters from the piping commodities part of the Piping
Job Specification:
MC GS Term(G)_Rat(G) Term(R)_Rat(R) A
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are surface area, weight of water
plus all those dimensional parameters required to display the component in the model whose
values are not defined in a generic table.
If columns available in the above table were insufficient to allow definition of all the applicable
dimensional parameters, the remaining parameters are included in a table with format P26B.
The name of the P26B table is comprised of the following parameters from the piping
commodities part of the Piping Job Specification:
MC GS Term(G)_Rat(G) Term(R)_Rat(R) B
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are those dimensional
parameters required to display the component in the model that were not included in the P26A
table.
The empty weight of the component is included in a table with format P62. The name of this
table is comprised of the following parameters from the piping commodities part of the Piping
Job Specification:
MC_GS_Term(G) Rat(G) Term(R) Rat(R) Sc/Th(R) WC
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The only dependent variable is empty weight of the
component.
109
Commodity Discussions
Green and Red Connect Point Data, GCP=Male, RCP=Male, MC WOL, SOL, TOL, NOL, EOL
or LOL
If both green and red connect point data appear in the definition of the component in the Piping
Job Specification and both the green and the red connect points are male termination types and
the model code is not WOL, SOL, TOL, NOL, EOL or LOL, the following applies:
General data about the component is included in a table with format P21A. The name of this
table is comprised of the following parameters from the piping commodities part of the Piping
Job Specification:
MC GS Term(G) Term(R) A
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are surface area, weight of water
plus all those dimensional parameters required to display the component in the model whose
values are not defined in a generic table.
If columns available in the above table were insufficient to allow definition of all the applicable
dimensional parameters, the remaining parameters are included in a table with format P21B.
The name of the P21B table is comprised of the following parameters from the piping
commodities part of the Piping Job Specification:
MC GS Term(G) Term(R) B
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are those dimensional
parameters required to display the component in the model that were not included in the P21A
table.
The empty weight of the component is included in a table with format P63. The name of this
table is comprised of the following parameters from the piping commodities part of the Piping
Job Specification:
MC_GS_Term(G) Sc/Th(G) Term(R) Sc/Th(R) WC
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The only dependent variable is empty weight of the
component.
Green and Red Connect Point Data, GCP=Male, RCP Male, MC WOL, SOL, TOL, NOL,
EOL or LOL
If both green and red connect point data appear in the definition of the component in the piping
commodities part of the Piping Job Specification, the green connect point is a male termination
type, the red connect point is not a male termination type and the model code is not WOL, SOL,
TOL, NOL, EOL or LOL, the following applies:
General data about the component is included in a table with format P27A. The name of this
table is comprised of the following parameters from the piping commodities part of the Piping
Job Specification:
MC_GS_Term(G) Term(R) Rat(R) A
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are surface area, weight of water
plus all those dimensional parameters required to display the component in the model whose
values are not defined in a generic table.
If columns available in the above table were insufficient to allow definition of all the applicable
dimensional parameters, the remaining parameters are included in a table with format P27B.
The name of the P27B table is comprised of the following parameters from the piping
commodities part of the Piping Job Specification:
110
Commodity Discussions
MC_GS_Term(G) Term(R) Rat(R) B
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are those dimensional
parameters required to display the component in the model that were not included in the P27A
table.
The empty weight of the component is included in a table with format P64. The name of this
table is comprised of the following parameters from the piping commodities part of the Piping
Job Specification:
MC_GS_Term(G) Sc/Th(G) Term(R) Rat(R) WC
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The only dependent variable is empty weight of the
component.
Green and Red Connect Point Data, GCP=Male, RCP=Male or Female, MC=WOL, SOL, TOL,
NOL, EOL or LOL
If both green and red connect point data appear in the definition of the component in the Piping
Job Specification, the green connect point is a male termination type, the red connect point is
either a male or a female termination type and the model code is WOL, SOL, TOL, NOL, EOL or
LOL, the following applies:
General data about the component is included in a table with format P28A. The name of this
table is comprised of the following parameters from the piping commodities part of the Piping
Job Specification:
MC_GS_Term(G) Sc/Th(G) Term(R) Rat/Sc/Th(R) A
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are surface area, weight of water
plus all those dimensional parameters required to display the component in the model whose
values are not defined in a generic table.
If columns available in the above table were insufficient to allow definition of all the applicable
dimensional parameters, the remaining parameters are included in a table with format P28B.
The name of the P28B table is comprised of the following parameters from the piping
commodities part of the Piping Job Specification:
MC_GS_Term(G) Sc/Th(G) Term(R) Rat/Sc/Th(R) B
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are those dimensional
parameters required to display the component in the model that were not included in the P28A
table.
The empty weight of the component is included in a table with format P65. The name of this
table is comprised of the following parameters from the piping commodities part of the Piping
Job Specification:
MC_GS_Term(G) Sc/Th(G) Term(R) Rat/Sc/Th(R) WC
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The only dependent variable is empty weight of the
component.
Unless otherwise indicated, all fittings are automatically placed in the Piping Task during
automatic component placement. Components to be placed automatically by the system will
be selected to match the CP preparation, CP rating and table suffix of the applicable CP of the
mating component or equipment nozzle.
Under the description of each table format applicable to each component type, the GCP and
RCP rating and schedule/thickness that needs to be provided in the Piping Job Specification
111
Commodity Discussions
has been listed. These values are required for one or more of the reasons indicated below and
will not necessarily be part of the names of the tables that include data about the component.
To procure the component.
To access data tables. Refer to Section 4, Model Graphics Definitions, for a description of
the table formats.
To supply data required for stress analysis purposes.
The AABBCC code for fittings will consist of the applicable AABB code, 6P3C or 6Q3C,
followed by two numbers for the specific type.
AABBCC
Description
112
Commodity Discussions
113
Commodity Discussions
TNF=P21A & P63
Beveled/plain ends
For GCP: Rating="-"; Sc/Th="Value"
For RCP: Rating="-"; Sc/Th="Value"
4 cuts miter (MC=M4) (SN=F114D)
TNF=P11A & P51
Beveled ends
For GCP: Rating="-"; Sc/Th="Value"
For RCP: Rating="-"; Sc/Th="-"
TNF=P21A & P63
Beveled/plain ends
For GCP: Rating="-"; Sc/Th="Value"
For RCP: Rating="-"; Sc/Th="Value"
The same nominal diameter must apply to both ends of these
miters.
The miter angle of these miters is determined by the
system from data in the design file and is supplied to
the component definition without need of user intervention.
The number of cuts in a miter will have to be "remembered"
by the system since this value is required in the
calculation of SIF applicable to the miter.
114
Commodity Discussions
TNF=P21A & P63
Beveled/plain ends
For GCP: Rating="-"; Sc/Th="Value"
For RCP: Rating="-"; Sc/Th="Value"
The same nominal diameter must apply to both ends of these
miters. The number of cuts in a miter will have to be
"remembered" by the system since this value is required
in the calculation of SIF applicable to the miter.
115
Commodity Discussions
TNF=P11A & P51
Beveled ends
For GCP: Rating="-"; Sc/Th="Value"
For RCP: Rating="-"; Sc/Th="-"
TNF=P21A & P63
Beveled/plain ends
For GCP: Rating="-"; Sc/Th="Value"
For RCP: Rating="-"; Sc/Th="Value"
The same nominal diameter must apply to both ends of these
miters. The number of cuts in a miter will have to be
"remembered" by the system since this value is required
in the calculation of SIF applicable to the miter.
116
Commodity Discussions
TNF=P25A & P61
Socket/male threaded ends
For GCP: Rating="Value"; Sc/Th="Value"
For RCP: Rating="-"; Sc/Th="NREQD"
TNF=P11A & P51
Beveled ends
Male grooved ends
For GCP: Rating="-"; Sc/Th="Value"
For RCP: Rating="-"; Sc/Th="-"
TNF=P21A & P63
Male grooved/male threaded ends
For GCP: Rating="-"; Sc/Th="Value"
For RCP: Rating="-"; Sc/Th="Value"
TNF=P27A & P64
Spigot/push-on bell ends
For GCP: Rating="-"; Sc/Th="NREQD"
For RCP: Rating="Value"; Sc/Th="NREQD"
Trimmable branch tee (MC=TBT) (SN=F122_1)
TNF=P11A & P51
Beveled ends
For GCP: Rating="-"; Sc/Th="Value"
For RCP: Rating="-"; Sc/Th="-"
The branch end of model code TBT is trimmed by the
software to the angle defined in the design file between the
segment run connected to the branch end of the component and
that connected to either header end of the component. The
placement of this component will not be automatic. The user
will first insert the component in the header and then continue
piping from CP3. The system will use data tables for T;
tables specific to TBT will not be required.
117
Commodity Discussions
TNF=P26A & P62
Mechanical joint/mechanical joint ends
For GCP: Rating="Value"; Sc/Th="NREQD" or "Value"
For RCP: Rating="Value"; Sc/Th="NREQD" or "Value"
TNF=P25A & P61
Mechanical joint/plain ends
For GCP: Rating="Value"; Sc/Th="NREQD" or "Value"
For RCP: Rating="-"; Sc/Th="NREQD"
TNF=P21A & P63
Beveled/beveled ends
Male grooved/male grooved ends
Male grooved/male threaded ends
For GCP: Rating="-"; Sc/Th="Value"
For RCP: Rating="-"; Sc/Th="Value"
TNF=P27A & P64
Socket/male threaded ends
For GCP: Rating="Value"; Sc/Th="Value"
For RCP: Rating="-"; Sc/Th="NREQD"
TNF=P27A & P64
Spigot/push-on bell ends
For GCP: Rating="-"; Sc/Th="NREQD"
For RCP: Rating="Value"; Sc/Th="NREQD"
Trimmable reducing branch tee (MC=TRBT) (SN=F122_1)
TNF=P11A & P51
Beveled ends
For GCP: Rating="-"; Sc/Th="Value"
For RCP: Rating="-"; Sc/Th="-"
The branch end of model code TRBT is trimmed by the
software to the angle defined in the design file between the
segment run connected to the branch end of the component and
that connected to either header end of the component. The
placement of this component will not be automatic. The user
will first insert it in the header and then continue
piping from CP3. The system will use data tables for TRB;
tables specific to TRBT will not be required.
118
Commodity Discussions
119
Commodity Discussions
120
Commodity Discussions
o The number of taps, up to 4, is defined in the "Mod"
column of the Piping Job Specification.
121
Commodity Discussions
TNF=P25A & P61
Mechanical joint/plain ends
For GCP: Rating="Value"; Sc/Th="NREQD" or "Value"
For RCP: Rating="-"; Sc/Th="NREQD"
TNF=P11A & P51
Beveled ends
Male grooved ends
For GCP: Rating="-"; Sc/Th="Value"
For RCP: Rating="-"; Sc/Th="-"
TNF=P27A & P64
Spigot/push-on bell ends
Plain/push-on bell ends
For GCP: Rating="-"; Sc/Th="NREQD"
For RCP: Rating="Value"; Sc/Th="NREQD"
122
Commodity Discussions
123
Commodity Discussions
124
Commodity Discussions
125
Commodity Discussions
TNF=P26A & P62
Socketwelded/socketwelded ends
Female threaded/female threaded ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="Value"; Sc/Th="NREQD"
It will only be possible to place components with two
different sizes.
126
Commodity Discussions
127
Commodity Discussions
128
Commodity Discussions
129
Commodity Discussions
Data defined for these components will allow the system to
determine the applicable stress intensification factors
(SIF) to be used in stress analysis of the piping system.
The thickness of the portion of piping from PCP2 of this
component to the centerline of the header is reported
as "RIGID" to the Pipe Stress Analysis software, regardless
of the value in the Piping Job Specification so as not to
provide a fictitious flexibility.
130
Commodity Discussions
This model code represents a "stub-in" reinforcing pad; that
is one in which the pipe terminates at the inside surface of
the header.
The following comments apply to all reinforcing pads:
o Reinforcing pads are defined in the piping materials
classes to have an actual value for fabrication category,
which may be changed after placement. In the isometric
drawings, a note will not be placed in the graphic part
of the drawing to show their size. A short description
has been prepared for reinforcing pads and is displayed
in the bill of materials.
o Reinforcing pads may be placed with either single or
double curvature, for example reinforcing a pipe or a head
respectively.
o The angle of intersection between the header and the
branch is part of the table name containing
dimensional parameters for the component. This angle will
be derived by the system from data in the design file.
Four different types of intersection is recognized:
- Intersections at angles equal to or greater than 20 but
less than 45 degrees: the number "2045" is used as
part of the table name.
- Intersections at 45 degrees: the number "45" is
used as part of the table name.
- Intersections at angles greater than 45 but lesser than
90 degrees: the number "4590" is used as part of
the table name.
- Intersections at 90 degrees: the number "90" is
used as part of the table name.
o Two possibilities exist regarding dimensions for a
reinforcing pad:
- If a "0" is entered in the "MOD" column of the Piping
Job Specification, dimensions are to be derived from
either a data table and/or from branch calculations.
For the case where no branch calculation is involved,
both the pad width and pad thickness are included in
the applicable dimension table. If a branch calculation
is involved, a value is provided in the dimension
table for pad width and either a "-" or value for pad
thickness. See section titled "Choosing a Branch
Connection from a Branches Table" for details.
- If a "1" is entered in such column, the system is to
prompt for dimensions. If dimensions are provided by
the user, their values are stored in the TDB so that in
subsequent recreations of the piping system, those
values and not those that might exist in a data table
are used by the system.
131
Commodity Discussions
o Data defined for these components will allow the system to
determine the applicable stress intensification factors
(SIF) to be used in stress analysis of the piping system.
o The thickness of the portion of piping from PCP2 of this
component to the centerline of the header is reported
as "RIGID" to the Pipe Stress Analysis software,
regardless of the value in the Piping Job Specification so
as not to provide a fictitious flexibility.
o The empty weight of these components is neglected.
132
Commodity Discussions
o The angle of intersection between the header and the
branch is part of the table name containing
dimensional parameters for the component. This angle will
be derived by the system from data in the design file.
Four different types of intersection is recognized:
- Intersections at angles equal to or greater than 20 but
less than 45 degrees: the number "2045" is used as
part of the table name.
- Intersections at 45 degrees: the number "45" is
used as part of the table name.
- Intersections at angles greater than 45 but lesser than
90 degrees: the number "4590" is used as part of
the table name.
- Intersections at 90 degrees: the number "90" is
used as part of the table name.
o Two possibilities exist regarding dimensions for a
reinforcing weld:
- If a "0" is entered in the "MOD" column of the Piping
Job Specification, dimensions are to be derived from
either a data table and/or from branch calculations.
For either case, a value is provided for the
reinforcing weld size in the applicable dimension table.
See section titled "Choosing a Branch Connection from a
Branches Table" for details.
- If a "1" is entered in such column, the system is to
prompt for dimensions. If dimensions are provided by
the user, their values are stored in the TDB so that in
subsequent recreations of the piping system, those values
and not those that might exist in a data table are used
by the system.
o Data defined for these components will allow the system to
determine the applicable stress intensification factors
(SIF) to be used in stress analysis of the piping system.
o The thickness of the portion of piping from PCP2 of this
component to the centerline of the header is reported
as "RIGID" to the Pipe Stress Analysis software,
regardless of the value in the Piping Job Specification so
as not to provide a fictitious flexibility.
o The empty weight of these components is neglected.
133
Commodity Discussions
134
Commodity Discussions
6Q3C95, Gasket
There is no model code for this piping component. It is only required in the piping materials class
for piping materials purposes.
TNF=None & None
For GCP: Rating="Value"; Sc/Th="-"
For RCP: Rating="-"; Sc/Th="-"
Gaskets are handled as follows:
At a bolted joint, bolted ends may be either thru-bolted or non-thru-bolted. Requirements
defined below apply to both thru-bolted and non-thru-bolted ends unless specifically indicated
otherwise.
A gasket entry is required for every combination of diameter, preparation, rating and table
suffix of nozzles, commodity components and/or specialty components to which the piping
materials class applies. For example, to account for a bolted joint including an orifice flange
and an orifice plate, two gasket entries must be defined: one with TS=29 for the orifice flange
end and the other one with TS-5 for the orifice plate end.
The definition of each gasket entry in the piping materials class will include values for each of
the parameters listed below.
AABBCC code: the value 6Q3C95 will always apply.
Option:: the value "1" will apply unless a different option value is defined as an override as
part of the placement of the commodity or specialty component for which the gasket is
intended.
GCP from-to: these entries will define the ranges of nominal diameters for which the
gasket is intended.
GCP preparation: these entries will define the end preparation for which the gasket is
intended. Gasket definitions should not be made for end preparations implying integral
gaskets. For a piping materials class in which all gaskets are integral, the gasket gap in
the Piping Job Specification table is defined as "0".
GCP rating: these entries will define the pressure rating for which the gasket is intended.
For this definition, the values of rating must omit characters such as "CL", "#" and "OT"
135
Commodity Discussions
even if these were used in the definition of the component to which the gasket will
correspond.
GCP table suffix: these entries will define the table suffix for which the gasket is intended.
Commodity code
TMx: this represents the maximum temperature for which use of the gasket is allowed. It
will also provide one of the search keys for the value of gasket gap in the Gasket Gaps
Table.
Geometry standard: the entry of a value for this parameter is optional. It has been entered
in the piping materials classes to assist the user in interpreting the definition of the gasket.
Mod: this attribute allows the definition of the compressed gasket thickness or other
gasket parameter that is required to procure the gasket.
Material grade: the entry of a value for this parameter is optional. It has been entered in
the piping materials classes to assist the user in interpreting the definition of the gasket.
Fabrication class: these entries will define the disposition that is made of the gasket for
material reporting and isometric purposes.
The default selection of a gasket is based upon option "1". If the user wishes to use a gasket at a
joint other than the default, he could do so by overriding during placement of a commodity or
specialty component the gasket override option that is to apply for gasket selection. The value of
this override option will apply to all the connect points of all bolted ends placed as part of
thatplacement operation. If one of the bolted ends to be placed is to mate a previously placed end
which has a different gasket override option, placement of the component will fail. The gasket gap
that will apply to the override gasket is determined by the system from a gasket gap table in a
manner analogous to that used for the default gaskets. During automatic component placement,
bolted ends added by the system to mate existing ends will inherit the values of gasket override
option that apply to the previously placed ends. During model reconstruction, the system will
respect the gasket override option defined during previous placements.
Two possibilities exist regarding gasket selection depending upon the value for end
preparation of the components at the bolted joint:
If one or both of the ends at the bolted joint has an end preparation indicating that an
integral gasket applies, no gasket is returned by the system.
If none of the ends at the bolted joint has an end preparation indicating that an integral
gasket applies, the system will proceed as follows:
The system will select for each bolted end in a bolted joint, from the piping materials
class, the gasket to use on the basis of the functional capability described under the
heading "Choosing Gasket at Bolted End".
After all gaskets are so determined at a bolted joint, the system will compare the
commodity codes and modifiers of mating ends. If they are identical, the gasket
selection is deemed to be successful; if not identical a fatal error is reported.
At the a bolted joint, regardless of the number of ends involved at the joint and of the design
volumes in which they might be found, the default ownership for all gaskets and studs required
by the joint is assigned by the system to the first non-thru-bolted end found by the system
during the gasket selection process. This characteristic only affects the ownership of such
gaskets and studs. The gasket selection itself is based on the criteria given in preceding
paragraphs and not on the properties of the first bolted end encountered by the system. If a
user needs to assign the ownership of gaskets and studs for the joint to a particular bolted end,
he may do so by setting the value of the applicable user-data attribute for the applicable
connect point to either "Default Gasket/Bolts/Nuts Ownership" or "Gasket/Bolts/Nuts Owned
by this Component". As was the case for the default ownership, this attribute only controls in
which isometric drawing the gaskets and studs are listed and not their selection basis.
136
Commodity Discussions
6Q3C97, Stud
There is no model code for this piping component. It is only required in the piping materials class
for piping materials purposes.
TNF=None & None
For GCP: Rating="Value"; Sc/Th="-"
For RCP: Rating="Value"; Sc/Th="-"
Studs are handled by the system as follows:
At a bolted joint, bolted ends may be either thru-bolted (with or without bolt holes) or
non-thru-bolted. Requirements defined below apply to both thru-bolted and non-thru-bolted
ends unless specifically indicated otherwise.
Users can specify whether thru-bolted ends include bolt holes or not. This distinction
does not affect the handling of studs in PDS, but it does affect pressure rating design checks
and flange placement. For more information, refer to the Piping Design Graphics Reference
Guide and the Reference Data Manager Reference Guide.
The definition of each stud entry in the piping materials class will include values for each of the
parameters listed below.
A stud entry is required for every combination of nominal diameter, preparation (only if the
RDB option that involves CP termination for bolt length calculations is active) and rating of
nozzles, commodity components and/or specialty components to which the piping
materials class applies.
AABBCC code: the value 6Q3C97 will always apply.
Option:: the value "1" will always apply.
GCP from-to: these entries will define the ranges of nominal diameter of the
non-thru-bolted ends of the bolted joint for which the stud is intended. Only data for the
GCP is provided regardless of whether the stud is intended for non-thru-bolted ends with
identical preparation and/or ratings or not.
GCP and RCP preparation: these entries will define the preparation of the non-thru-bolted
ends of the bolted joint for which the stud is intended. Two possibilities exist:
The stud is intended for non-thru-bolted ends with identical preparations and rating,
the value of the preparation will only be included in the GCP preparation column; a "-"
is included for the RCP preparation.
The stud is intended for mating bolted ends with different either preparation or rating:
the properties of the end(s) with the lowest codelist number defining its CP
preparation, regardless of the values for rating, is defined under the GCP data.
GCP and RCP rating: these entries will define the pressure rating of the non-thru-bolted
ends of the bolted joint for which the stud is intended. For this definition, the values of
rating must omit characters such as "CL", "#" and "OT" even if these were used in the
definition of the component to which the stud will correspond. The following possibilities
exist:
The stud is intended for non-thru-bolted ends with identical preparations and ratings:
the value of the rating will only be included in the GCP rating column; a "-" is included
for the RCP rating.
The stud is intended for mating bolted ends with identical preparations but different
ratings: the value of the stronger rating is included in the GCP rating column; the
value of the weaker rating is included in the RCP rating column. This situation is
commonly found, for example, due to equipment nozzle rating differing from that of
the mating piping component flange.
137
Commodity Discussions
138
The stud is intended for mating bolted ends with different preparations and ratings:
the properties of the end(s) with the lowest codelist number defining its CP
preparation is defined under the GCP data.
Commodity code: a different commodity code is assigned, for example, to:
Studs which are always lubricated.
Studs which are only lubricated when they exceed a given bolt diameter.
Studs which are never lubricated.
TMx: this represents the maximum temperature at which use of the stud is allowed.
Geometry standard: the entry of a value for this parameter is optional. It has been
entered in the piping materials classes to assist the user in interpreting the definition of the
stud.
Mod: the following characteristics apply:
The sign used for this attribute defines whether a stud (+ or no sign) or a machine bolt
(-) is involved.
The value "0" defines studs that will use nuts of standard nut allowance. The value
"1" defines machine bolts that will use nuts of standard nut allowance. Values "2"
through "5" define either studs (+ or no sign) or machine bolts (-) that use special nut
allowances.
Material grade: the entry of a value for this parameter is optional. It has been entered in
the piping materials classes to assist the user in interpreting the definition of the stud.
Fabrication class: these entries will define the disposition that is made of the stud for
material reporting and isometric purposes.
The system will select, from the piping materials class of the end that owns the joint, the stud
to use and its applicable data on the basis of the functional capability described under the
heading "Choosing Stud at Bolted Joint".
The system will access for each non-thru-bolted end in a bolted joint the applicable of the
tables described below.
STUD_Rat_TS, if the RDB option that involves CP termination for bolt length calculations
is not active (in the WS software, the 'almost precise' value applies to the corresponding
toggle switch); or
STUD_Term_Rat_TS, if the RDB option that involves CP termination for bolt length
calculations is active (in the WS software, the 'precise' value applies to the corresponding
toggle switch).
To determine the number and diameter of bolts required and the nut allowance to be used.
The system will use the termination type (only if the RDB option that involves CP termination
for bolt length calculations is active), rating and table suffix of the applicable bolted end to
select the stud table to use. No similar access to a stud table is made for the thru-bolted ends
of the joint. If identical values for number and diameter of bolts are derived from all the stud
tables that were accessed for the bolted joint, regardless of whether the bolted ends are in the
same or in different design volumes, the system will proceed. If different values are derived,
a fatal error is reported.
The value of nut allowance selected for each bolted end will depend upon the value of the
modifier parameter read in the piping materials class for the stud applicable to the joint. The
actual value of nut allowance selected for each non-thru-bolted ends of the bolted joint is used
in the determination of bolt length for the joint.
Both thru-bolted ends and non-thru-bolted ends will have a BLT_Term_Rat_TS tables
associated with them. Tables for non-thru-bolted ends will have actual values for bolt circle
diameter. Tables for thru-bolted ends will have dashes for bolt circle diameter. The system
Commodity Discussions
will access for each non-thru-bolted end in the bolted joint the corresponding
BLT_Term_Rat_TS table to determine the bolt circle diameter that applies. If identical values
for bolt circle diameter are derived, the system will proceed. If different values are derived, a
fatal error is reported.
Stud and machine bolt lengths are calculated by the system as the sum of the following:
The values for all dimensions "R" derived from the applicable generic tables for all
non-thru-bolted ends involved in the bolted connection, plus
The values for all "face to face" dimensions stored in the TDB for all thru-bolted ends
involved in the bolted connection (it is essential that the value stored in the TDB for this
parameter truly be a face to face dimension and not a connect point to connect point
dimension), plus
The values for all gasket gaps involved in the bolted connection, plus
The total nut allowances, as defined below:
For studs: the sum of the nut allowances derived from the applicable of the tables
described below:
STUD_Rat_TS, if the RDB option that involves CP termination for bolt length
calculations is not active (in the WS software, the 'almost precise' value applies to the
corresponding toggle switch);
STUD_Term_Rat_TS, if the RDB option that involves CP termination for bolt length
calculations is active (in the WS software, the 'precise' value applies to the
corresponding toggle switch).
for the non-thru-bolted ends of the joint.
For machine bolts: the larger of the nut allowances derived from the applicable of the
tables described below:
STUD_Rat_TS, if the RDB option that involves CP termination for bolt length
calculations is not active (in the WS software, the 'almost precise' value applies to the
corresponding toggle switch).
STUD_Term_Rat_TS, if the RDB option that involves CP termination for bolt length
calculations is active (in the WS software, the 'precise' value applies to the
corresponding toggle switch).
for the non-thru-bolted ends of the joint, plus
For the termination types defined below, which represent "lap type" ends, the
schedule/thickness from the TDB of the RCP of each non-thru bolted end involved in the
flanged joint.
60 = FFLFTP [Flat-face lap-flanged termination type] (61-69)
70 = RFLFTP [Raised-face lap-flanged termination type] (71-79)
80 = RJFLFTP [RTJ-face lap-flanged termination type](81-89)
90 = TMFLFTP [Tongue/male-face lap-flanged termination type] (91-99)
100 = GFFLFTP [Groove/female-face lap-flanged termination type]
(101-109)
The resulting value will then be rounded up to the value indicated in table BOLT_LENGTH.
At the a bolted joint, regardless of the number of ends involved at the joint and of the design
volumes in which they might be found, the default ownership for all gaskets and studs required
by the joint is assigned by the system to the first non-thru-bolted end found by the system
during the stud selection process. This characteristic only affects the ownership of such
gaskets and studs. The stud selection itself is based on the criteria given in preceding
paragraphs and not on the properties of the first bolted end encountered by the system. If the
user has the need of assigning the ownership of gaskets and studs for the joint to a particular
139
Commodity Discussions
bolted end, he may do so by setting the value of the applicable user-data attribute for the
applicable connect point to either "Default Gasket/Bolts/Nuts Ownership" or
"Gasket/Bolts/Nuts Owned by this Component". As was the case for the default ownership,
this attribute only controls in which isometric drawing the gaskets and studs are listed and not
their selection basis.
See Also
Connect Point Data (on page 141)
6Q4C01, Fire monitor (in-line) (on page 145)
6Q4C02, Elevated fire monitor (in-line) (on page 145)
6Q4C03, Remotely operated fire monitor (in-line) (on page 145)
6Q4C04, Foam monitor (in-line) (on page 146)
6Q4C05 Elevated foam monitor (in-line) (on page 146)
6Q4C06, Remotely operated foam monitor (in-line) (on page 146)
6Q4C10, [2-way] fire hydrant (in-line) (on page 147)
6Q4C11, [2-way] fire hydrant w/monitor nozzle (in-line) (on page 147)
6Q4C13, 3-way fire hydrant (in-line) (on page 147)
6Q4C24, Hose reel (in-line) (on page 148)
6Q4C25, Hose rack station (in-line) (on page 148)
6Q4C26, Foam chamber (in-line) (on page 148)
6P4C30, Wet sprinkler (on-line) (on page 148)
6P4C31, Pre-action sprinkler (on-line) (on page 149)
6P4C32, Spray sprinkler (on-line) (on page 149)
6Q4C38, Eye wash (in-line) (on page 149)
6Q4C39, Safety shower (in-line) (on page 149)
6Q4C40, Safety shower and eye wash (in-line) (on page 149)
6Q4C60, [2-way] siamese (in-line) (on page 150)
6Q4C66, [2-way] 90 deg siamese (in-line) (on page 150)
140
Commodity Discussions
The only independent variable in this table is the nominal diameter of the green connect point
of the component. The dependent variables are those dimensional parameters required to
display the component in the model that were not included in the P11A table.
The empty weight of the component is included in a table with format P51. The name of this
table is comprised of the following parameters from the piping commodities part of the Piping
Job Specification:
MC GS Term(G)_Sc/Th(G) WC
The only independent variable in this table is the nominal diameter of the green connect point
of the component. The only dependent variable is empty weight of the component.
141
Commodity Discussions
MC GS Term(G) Rat(G) B
The only independent variable in this table is the nominal diameter of the green connect point
of the component. The dependent variables are those dimensional parameters required to
display the component in the model that were not included in the P15A table.
The empty weight of the component is included in a table with format P52. The name of this
table is comprised of the following parameters from the piping commodities part of the Piping
Job Specification:
MC GS Term(G)_Rat(G) Sc/Th(G) WC
The only independent variable in this table is the nominal diameter of the green connect point
of the component. The only dependent variable is empty weight of the component.
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are those dimensional
parameters required to display the component in the model that were not included in the P25A
table.
The empty weight of the component is included in a table with format P61. The name of this
table is comprised of the following parameters from the piping commodities part of the Piping
Job Specification:
MC GS Term(G)_Rat(G) Term(R)_Sc/Th(R) WC
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The only dependent variable is empty weight of the
component.
Green and Red Connect Point Data, GCP Male, RCP Male
If both green and red connect point data appears in the definition of the component in the Piping
Job Specification and neither the green nor the red connect points are male termination types, the
following applies:
General data about the component is included in a table with format P26A. The name of this
table is comprised of the following parameters from the piping commodities part of the Piping
Job Specification:
MC GS Term(G)_Rat(G) Term(R)_Rat(R) A
142
Commodity Discussions
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are surface area, weight of water
plus all those dimensional parameters required to display the component in the model whose
values are not defined in a generic table.
If columns available in the above table were insufficient to allow definition of all the applicable
dimensional parameters, the remaining parameters are included in a table with format P26B.
The name of the P26B table is comprised of the following parameters from the piping
commodities part of the Piping Job Specification:
MC GS Term(G)_Rat(G) Term(R)_Rat(R) B
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are those dimensional
parameters required to display the component in the model that were not included in the P26A
table.
The empty weight of the component is included in a table with format P62. The name of this
table is comprised of the following parameters from the piping commodities part of the Piping
Job Specification:
MC_GS_Term(G) Rat(G) Term(R) Rat(R) Sc/Th(R) WC
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The only dependent variable is empty weight of the
component.
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are those dimensional
parameters required to display the component in the model that were not included in the P21A
table.
The empty weight of the component is included in a table with format P63. The name of this
table is comprised of the following parameters from the piping commodities part of the Piping
Job Specification:
MC_GS_Term(G) Sc/Th(G) Term(R) Sc/Th(R) WC
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The only dependent variable is empty weight of the
component.
143
Commodity Discussions
Green and Red Connect Point Data, GCP=Male, RCP Male
If both green and red connect point data appears in the definition of the component in the Piping
Job Specification, the green connect point is a male termination type and the red connect point is
not a male termination type, the following applies:
General data about the component is included in a table with format P27A. The name of this
table is comprised of the following parameters from the piping commodities part of the Piping
Job Specification:
MC_GS_Term(G) Term(R) Rat(R) A
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are surface area, weight of water
plus all those dimensional parameters required to display the component in the model whose
values are not defined in a generic table.
If columns available in the above table were insufficient to allow definition of all the applicable
dimensional parameters, the remaining parameters are included in a table with format P27B.
The name of the P27B table is comprised of the following parameters from the piping
commodities part of the Piping Job Specification:
MC_GS_Term(G) Term(R) Rat(R) B
144
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are those dimensional
parameters required to display the component in the model that were not included in the P27A
table.
The empty weight of the component is included in a table with format P64. The name of this
table is comprised of the following parameters from the piping commodities part of the Piping
Job Specification:
MC_GS_Term(G) Sc/Th(G) Term(R) Rat(R) WC
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The only dependent variable is empty weight of the
component.
Fire and safety piping components are not placed during automatic component placement.
They must be positioned manually.
Under the description of each table format applicable to each component type, the GCP and
RCP rating and schedule/thickness that needs to be provided in the Piping Job Specification
has been listed. These values are required for one or more of the reasons indicated below and
will not necessarily be part of the names of the tables that include data about the component.
To procure the component.
To access data tables. Refer to section Model Graphics Definitions for a description of the
table formats.
To supply data required for stress analysis purposes.
The AABBCC code for fire and safety piping components consists of the applicable AABB
code, 6P4C or 6Q4C, followed by two numbers for the specific type of component.
Commodity Discussions
145
Commodity Discussions
146
Commodity Discussions
147
Commodity Discussions
148
Commodity Discussions
??
149
Commodity Discussions
150
Commodity Discussions
151
Commodity Discussions
152
Commodity Discussions
153
Commodity Discussions
154
Commodity Discussions
155
Commodity Discussions
156
Commodity Discussions
157
Commodity Discussions
158
Commodity Discussions
159
Commodity Discussions
Bio-Pharmaceutical Operators
SOP3, Manual bonnet (in-line) (not-automatic)
Manual bonnet (MC=SOP_3) (ISK=N/A)
TNF='MB'_GS_OP_A
160
Commodity Discussions
161
Commodity Discussions
162
Commodity Discussions
163
Commodity Discussions
See Also
Named and Unamed Specialties (on page 165)
Connect Point Data (on page 165)
6Q6C01, Flame arrestor (in-line) (PID piping comp type 513) (on page 168)
6Q6C03, Hammer arrestor (in-line) (PID piping comp type 515) (on page 168)
6Q6C04, Vent silencer (in-line) (PID piping comp type 516) (on page 168)
6Q6C05, In-line silencer (in-line) (PID piping comp type 517) (on page 168)
6Q6C07, Exhaust head (in-line) (PID piping comp type 519) (on page 169)
6Q6C09, Breather vent (in-line) (PID piping comp type 521) (on page 169)
6Q6C11, Free vent w/o screen (in-line) (PID piping comp type 523) (on page 169)
6Q6C12, Free vent w/screen (in-line) (PID piping comp type 524) (on page 169)
6Q6C13, Motor operated valve (in-line) (with operator) (on page 169)
6Q6C15, Mixing T (in-line) (PID piping comp type 527) (on page 169)
6P6C17, Spray nozzle (on-line) (PID piping comp type 529) (on page 169)
6Q6C21, Removable spool (in-line) (PID piping comp type 533) (on page 170)
6Q6C23, Swing elbow (in-line) (PID piping comp type 535) (on page 170)
6Q6C28, Expansion joint (in-line) (PID piping comp type 540) (on page 170)
6Q6C30, Hinged expansion joint (in-line) (PID piping comp type 542) (on page 170)
6Q6C32, Swivel joint (in-line) (PID piping comp type 544) (on page 170)
6Q6C34, Mechanical coupling (in-line) (PID piping comp type 546) (on page 171)
6Q6C36, Flexible hose (in-line) (PID piping comp type 548) (on page 171)
6Q6C40, Sample cooler (in-line) (PID piping comp type 552) (on page 172)
6Q6C45, Single basket strainer (in-line) (PID piping comp type 557) (on page 172)
6Q6C47, Duplex basket strainer (in-line with operator) (PID piping comp type 559) (on page
172)
6Q6C49, T strainer (in-line) (PID piping comp type 561) (on page 172)
6Q6C51, Y strainer (in-line) (PID piping comp type 563) (on page 173)
6Q6C52, Temporary strainer (in-line) (PID piping comp type 564) (on page 173)
6Q6C53, Basket strainer (in-line) (PID piping comp type 565) (on page 173)
6Q6C55, Cone strainer (in-line) (PID piping comp type 567) (on page 174)
6Q6C57, Flat plate strainer (in-line) (PID piping comp type 569) (on page 174)
6Q6C59, Sump strainer (in-line) (PID piping comp type 571) (on page 174)
6Q6C64, Filter (in-line) (PID piping comp type 576) (on page 174)
6Q6C70, Steam trap (in-line) (PID piping comp type 582) (on page 174)
6Q6C71, Float steam trap (in-line) (PID piping comp type 583) (on page 174)
6Q6C72, Inverted bucket steam trap (in-line) (PID piping comp type 584) (on page 174)
6Q6C74, Thermostatic steam trap (in-line) (PID piping comp type 586) (on page 174)
6Q6C76, Thermodynamic steam trap (in-line) (PID piping comp type 588) (on page 174)
6Q6C78, Impulse steam trap (in-line) (PID piping comp type 590) (on page 174)
6Q6C99, Generic component (in-line) (PID piping comp type 611) (on page 175)
164
Commodity Discussions
165
Commodity Discussions
If the termination type of the ends are the same but the values for rating, schedule or
thickness differ, the properties of the "stronger" ends(s) have been defined under the
green connect point data.
For each piping specialty component, dimensional data is defined in tables, as follows:
Named Specialty - If the component is named, regardless of its other characteristics, the
following applies:
Both generic and specific data about the component is included in the applicable unit of
the Instrument TDB.
Refer to the explanation given under table format P80 for details.
Unnamed Specialty, GCP = male - If the component is unnamed, if only green connect point
data appears in the definition of the component in the piping specialties part of the Piping Job
Specification and if the connect point is a male termination type, the following applies:
Data about the component is included in a table with format P81. The name of this table is
comprised of the following parameters from the piping specialties part of the Piping Job
Specification:
MC GS Term(G) Unnamed_P
The only independent variable in this table is the nominal diameter of the green connect point
of the component. The dependent variables are surface area, empty weight, weight of water,
weight of the operator plus all those dimensional parameters required to display the
component and its operator, if any, in the model whose values are not defined in a generic
table.
Unnamed Specialty, GCP male - If the component is unnamed, if only green connect point
data appears in the definition of the component in the piping specialties part of the Piping Job
Specification and if the connect point is not a male termination type, the following applies:
Data about the component is included in a table with format P85. The name of this table is
comprised of the following parameters from the piping specialties part of the Piping Job
Specification:
MC GS Term(G) Rat(G) Unnamed_P
The only independent variable in this table is the nominal diameter of the green connect point
of the component. The dependent variables are surface area, empty weight, weight of water,
weight of the operator plus all those dimensional parameters required to display the
component and its operator, if any, in the model whose values are not defined in a generic
table.
Unnamed Specialty, GCP=bolted or female, RCP=male - If the component is unnamed, if
both green and red connect point data appears in the definition of the component in the piping
specialties part of the Piping Job Specification, the "green" connect point is either a bolted or a
female termination type and the red connect point is a male termination type, the following
applies:
Data about the component is included in a table with format P95. The name of this table is
comprised of the following parameters from the piping specialties part of the Piping Job
Specification:
MC GS Term(G)_Rat(G) Term(R)_Unnamed_P
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are surface area, empty weight,
weight of water, weight of the operator plus all those dimensional parameters required to
display the component and its operator, if any, in the model whose values are not defined in a
generic table.
166
Unnamed Specialty, GCP male, RCP male - If the component is unnamed, if both green
and red connect point data appears in the definition of the component in the piping specialties
Commodity Discussions
part of the Piping Job Specification and neither the green nor the red connect points are male
termination types, the following applies:
Data about the component is included in a table with format P96. The name of this table is
comprised of the following parameters from the piping specialties part of the Piping Job
Specification:
MC GS Term(G)_Rat(G) Term(R)_Rat(R) Unnamed_P
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are surface area, empty weight,
weight of water, weight of the operator plus all those dimensional parameters required to
display the component and its operator, if any, in the model whose values are not defined in a
generic table.
Unnamed Specialty, GCP=male, RCP=male - If the component is unnamed, if both green
and red connect point data appears in the definition of the component in the piping specialties
part of the Piping Job Specification and both the green and the red connect points are male
termination types, the following applies:
Data about the component is included in a table with format P91. The name of this table is
comprised of the following parameters from the piping specialties part of the Piping Job
Specification:
MC GS Term(G) Term(R) Unnamed_P
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are surface area, empty weight,
weight of water, weight of the operator plus all those dimensional parameters required to
display the component and its operator, if any, in the model whose values are not defined in a
generic table.
Unnamed Specialty, GCP=male, RCP male - If the component is unnamed, if both green
and red connect point data appears in the definition of the component in the piping specialties
part of the Piping Job Specification, the "green" connect point is a male termination type and
the red connect point is not a male termination type, the following applies:
Data about the component is included in a table with format P97. The name of this table is
comprised of the following parameters from the piping specialties part of the Piping Job
Specification:
MC_GS_Term(G) Term(R) Rat(R) Unnamed_P
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are surface area, empty weight,
weight of water, weight of the operator plus all those dimensional parameters required to
display the component and its operator, if any, in the model whose values are not defined in a
generic table.
Piping specialty components will not have operators unless otherwise specifically indicated in
paragraphs that follow. Operators, if applicable, will always be defined independent of the
components. Refer to paragraph C6.1 for additional requirements regarding operators.
Piping specialty components and their operators are not placed during automatic component
placement. They must be positioned manually.
Reference to "ends" in component type definitions that follow refer to the applicable of in-line
or tap ends that might apply to the component.
Under the description of each table format applicable to each component type, the GCP and
RCP rating and schedule/thickness that needs to be provided in the Piping Job Specification
has been listed. These values are required for one or more of the reasons indicated below and
will not necessarily be part of the names of the tables that include data about the component.
To procure the component.
167
Commodity Discussions
To access data tables. Refer to Section 4, Model Graphics Definitions, for a description of
the table formats.
To supply data required for stress analysis purposes.
The following general comments apply to the use of symbols used to depict these piping specialty
components:
The symbols shown below under each piping specialty component type are only suggested
symbols that can be used to depict such piping specialty components. Any piping specialty
component symbol defined in Paragraph C.3.1 may be used instead.
Insure that for each symbol used, a proper match has been to an Isogen symbol.
Unless specifically defined otherwise, symbols listed below have been defined so that they
can be placed either with or without actuators.
Taps may be placed during the design session as required to define connections whose
definition is not possible with the symbol chosen.
The AABBCC code for piping specialty components consists of the applicable AABB code, 6P6C
or 6Q6C, followed by two numbers for the specific component type.
168
Commodity Discussions
169
Commodity Discussions
170
Commodity Discussions
171
Commodity Discussions
172
Commodity Discussions
173
Commodity Discussions
174
Commodity Discussions
Steam trap, commodity type 4, (MC=S32BC) (SN=S32BC)
Steam trap, commodity type 5, (MC=S64BC) (SN=S64BC)
Steam trap, commodity type 6, (MC=S70AC) (SN=S70AC)
Steam trap, commodity type 7, (MC=S70BC) (SN=S70BC)
Steam trap, commodity type 8 (no actuator), (MC=S78AC)
(SN=S78AC)
TNF=P15A & P59
Socketwelded ends
Female threaded ends
For GCP: Rating="Value"; Sc/Th="NREQD"
For RCP: Rating="-"; Sc/Th="-"
Steam trap, specialty type 1, (MC=S1AT or S1AS) (SN=S1AZ)
Steam trap, specialty type 2, (MC=S3AT or S3AS) (SN=S3AZ)
Steam trap, specialty type 3, (MC=S4AT or S4AS) (SN=S4AZ)
Steam trap, specialty type 4, (MC=S32BT or S32BS) (SN=S32BZ)
Steam trap, specialty type 5, (MC=S64BT or S64BS) (SN=S64BZ)
Steam trap, specialty type 6 (no actuator), (MC=S78AT or
S78AS) (SN=S78AZ)
175
Commodity Discussions
See Also
Named and Unnamed Instruments (on page 177)
Connect Point Data (on page 178)
7P1E01, [2-way generic body] control valve (in-line) (on page 181)
7P1E02, [2-way generic body] angle control valve (in-line) (on page 181)
7P1E03, 3-way [generic body] control valve (in-line) (on page 181)
7P1E04, 4-way [generic body] control valve (in-line) (on page 181)
7P1E05, [2-way] angle globe control valve (in-line) (on page 181)
7P1E06, 3-way globe control valve (in-line) (on page 181)
7P1E07, [2-way] solenoid valve (in-line) (on page 181)
7P1E08, [2-way] angle solenoid valve (in-line) (on page 182)
7P1E09, 3-way solenoid valve (in-line) (on page 182)
7P1E10, 4-way solenoid valve (in-line) (on page 182)
7P1E11, 3-way plug control valve (in-line) (on page 182)
7P1E12, 4-way plug control valve (in-line) (on page 182)
7P1E13, [2-way] ball control valve (in-line) (on page 182)
176
Commodity Discussions
7P1E14, 3-way ball control valve (in-line) (on page 182)
7P1E15, [2-way] globe control valve (in-line) (on page 183)
7P1E16, [2-way] plug control valve (in-line) (on page 183)
7P1E17, [2-way] butterfly control valve (in-line) (on page 183)
7P1E18, [2-way] knife gate control valve (in-line) (on page 183)
7P1E19, [2-way] diaphragm control valve (in-line) (on page 183)
7P1E20, [2-way] slide control valve (in-line) (on page 183)
7P1E21, 3-way slide control valve (in-line) (on page 183)
7P1E22, [2-way] multivane 1 damp/louv CV (in-line) (on page 184)
7P1E23, [2-way] multivane 2 damp/louv CV (in-line) (on page 184)
7P1E24, [2-way] single vane damp/louv CV (in-line) (on page 184)
7P1E27, Control valve w/equip (in-line) (on page 184)
7P1E30, Automatic recirculation valve (in-line) (on page 184)
7P1E33, Self contained press red reg (in-line) (on page 184)
7P1E34, Press red reg w/ ext tap (in-line) (on page 185)
7P1E35, Press red reg w/ int RV (in-line) (on page 185)
7P1E38, Self contained backpress reg (in-line) (on page 185)
7P1E39, Backpress reg w/ ext tap (in-line) (on page 185)
7P1E42, Diff press red reg w/int & ext taps (in-line) (on page 185)
7P1E44, [2-way] filled system temp reg (in-line) (on page 185)
7P1E45, [2-way] angle filled system temp reg (in-line) (on page 185)
7P1E46, 3-way filled system temp reg (in-line) (on page 186)
177
Commodity Discussions
Unnamed Instrument, GCP male - If the component is unnamed, if only green connect
point data appears in the definition of the component in the instrument specialties part of the
Piping Job Specification and if the connect point is not a male termination type, the following
applies:
Data about the component is included in a table with format I85. The name of this table is
comprised of the following parameters from the instrument specialties part of the Piping Job
Specification:
MC GS Term(G) Rat(G) Unnamed_I
The only independent variable in this table is the nominal diameter of the green connect point
of the component. The dependent variables are surface area, empty weight, weight of water,
weight of the actuator plus all those dimensional parameters required to display the
178
Commodity Discussions
component and its actuator, if any, in the model whose values are not defined in a generic
table.
Unnamed Instrument, GCP=bolted or female, RCP=male - If the component is unnamed, if
both green and red connect point data appears in the definition of the component in the
instrument specialties part of the Piping Job Specification, the green connect point is either a
bolted or a female termination type and the red connect point is a male termination type, the
following applies:
Data about the component is included in a table with format I95. The name of this table is
comprised of the following parameters from the instrument specialties part of the Piping Job
Specification:
MC GS Term(G)_Rat(G) Term(R)_Unnamed_I
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are surface area, empty weight,
weight of water, weight of the actuator plus all those dimensional parameters required to
display the component and its actuator, if any, in the model whose values are not defined in a
generic table.
Unnamed Instrument, GCP male, RCP male - If the component is unnamed, if both
green and red connect point data appears in the definition of the component in the instrument
specialties part of the Piping Job Specification and neither the green nor the red connect
points are male termination types, the following applies:
Data about the component is included in a table with format I96. The name of this table is
comprised of the following parameters from the instrument specialties part of the Piping Job
Specification:
MC GS Term(G)_Rat(G) Term(R)_Rat(R) Unnamed_I
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are surface area, empty weight,
weight of water, weight of the actuator plus all those dimensional parameters required to
display the component and its actuator, if any, in the model whose values are not defined in a
generic table.
Unnamed Instrument, GCP=male, RCP=male - If the component is unnamed, if both green
and red connect point data appears in the definition of the component in the instrument
specialties part of the Piping Job Specification and both the green and the red connect points
are male termination types, the following applies:
Data about the component is included in a table with format I91. The name of this table is
comprised of the following parameters from the instrument specialties part of the Piping Job
Specification:
MC GS Term(G) Term(R) Unnamed_I
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are surface area, empty weight,
weight of water, weight of the actuator plus all those dimensional parameters required to
display the component and its actuator, if any, in the model whose values are not defined in a
generic table.
Unnamed Instrument, GCP=male, RCP male - If the component is unnamed, if both green
and red connect point data appears in the definition of the component in the instrument
specialties part of the Piping Job Specification, the green connect point is a male termination
type and the red connect point is not a male termination type, the following applies:
Data about the component is included in a table with format I97. The name of this table is
comprised of the following parameters from the instrument specialties part of the Piping Job
Specification:
179
Commodity Discussions
MC_GS_Term(G) Term(R) Rat(R) Unnamed_I
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are surface area, empty weight,
weight of water, weight of the actuator plus all those dimensional parameters required to
display the component and its actuator, if any, in the model whose values are not defined in a
generic table.
Control valves and regulators will have actuators unless otherwise specifically indicated in
paragraphs that follow. Actuators are defined independent of the components unless otherwise
specifically indicated in paragraphs that follow. Refer to paragraph C6.1 for additional
requirements regarding actuators.
Control valves and regulators and their actuators will not be automatically placed during automatic
component placement. They will always be positioned by the User.
Reference to ends in component type definitions that follow refer to the applicable of in-line or tap
ends that might apply to the component.
Under the description of each table format applicable to each component type, the GCP and RCP
rating and schedule/thickness that needs to be provided in the Piping Job Specification has been
listed. These values are required for one or more of the reasons indicated below and will not
necessarily be part of the names of the tables that include data about the component.
To procure the component.
To access data tables. Refer to section Model Graphics Definitions for a description of the
table formats.
To supply data required for stress analysis purposes.
The following general comments apply to the use of symbols used to depict these
instruments:
The symbols shown below under each instrument type are only suggested symbols that
can be used to depict such instruments. Any instrument symbol defined in Paragraphs
C5.2, C5.3, C5.4 or C5.5 may be used instead.
Ensure that for each symbol used, a proper match has been to an Isogen symbol.
Unless specifically defined otherwise, symbols listed below have been defined so that
they can be placed either with or without actuators.
Taps may be placed during the design session as required to define connections whose
definition is not possible with the symbol chosen.
The AABBCC code for control valves and regulators will consist of the applicable AABB code,
7P1E, followed by two numbers for the specific instrument.
180
Commodity Discussions
(SN=I7AZ)
181
Commodity Discussions
182
Commodity Discussions
183
Commodity Discussions
184
Commodity Discussions
7P1E42, Diff press red reg w/int & ext taps (in-line)
(P&ID instr comp type=113)
Diff press red reg w/int & ext taps type 1 (MC=I7AT or I7AS)
(SN=I7AZ)
185
Commodity Discussions
See Also
Named or Unnamed Relief Devices (on page 187)
Connect Point Data (on page 187)
7P2C01, Angle press relief valve (in-line) (on page 190)
7P2C06, Straight-thru press relief valve (in-line) (on page 190)
7P2C09, Vac relief valve (in-line) (on page 190)
7P2C12, Press/vac relief valve (in-line) (on page 191)
7P2C14, Press/vac relief manhole cover (in-line) (on page 191)
7P2C16, Press relief rupture disc (in-line) (on page 191)
7P2C18, Vac relief rupture disc (in-line) (on page 191)
7P2C20, Temp fusible plug or disc (in-line) (on page 191)
186
Commodity Discussions
187
Commodity Discussions
Named Instruments - If the component is named, regardless of its other characteristics, the
following applies:
Both generic and specific data about the component is included in the applicable unit of the
Instrument TDB.
Refer to the explanation given under table format I80 for details.
Unnamed Instrument, GCP=male - If the component is unnamed, if only green connect point
data appears in the definition of the component in the instrument specialties part of the Piping
Job Specification and if the connect point is a male termination type, the following applies:
Data about the component is included in a table with format I81. The name of this table is
comprised of the following parameters from the instrument specialties part of the Piping Job
Specification:
MC GS Term(G) Unnamed_I
The only independent variable in this table is the nominal diameter of the green connect point
of the component. The dependent variables are surface area, empty weight, weight of water,
weight of the actuator plus all those dimensional parameters required to display the
component and its actuator, if any, in the model whose values are not defined in a generic
table.
Unnamed Instrument, GCP male - If the component is unnamed, if only green connect
point data appears in the definition of the component in the instrument specialties part of the
Piping Job Specification and if the connect point is not a male termination type, the following
applies:
Data about the component is included in a table with format I85. The name of this table is
comprised of the following parameters from the instrument specialties part of the Piping Job
Specification:
MC GS Term(G) Rat(G) Unnamed_I
The only independent variable in this table is the nominal diameter of the green connect point
of the component. The dependent variables are surface area, empty weight, weight of water,
weight of the actuator plus all those dimensional parameters required to display the
component and its actuator, if any, in the model whose values are not defined in a generic
table.
Unnamed Instrument, GCP=bolted or female, RCP=male - If the component is unnamed, if
both green and red connect point data appears in the definition of the component in the
instrument specialties part of the Piping Job Specification, the green connect point is either a
bolted or a female termination type and the red connect point is a male termination type, the
following applies:
Data about the component is included in a table with format I95. The name of this table is
comprised of the following parameters from the instrument specialties part of the Piping Job
Specification:
MC GS Term(G)_Rat(G) Term(R)_Unnamed_I
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are surface area, empty weight,
weight of water, weight of the actuator plus all those dimensional parameters required to
display the component and its actuator, if any, in the model whose values are not defined in a
generic table.
188
Unnamed Instrument, GCP male, RCP male - If the component is unnamed, if both
green and red connect point data appears in the definition of the component in the instrument
specialties part of the Piping Job Specification and neither the green nor the red connect
points are male termination types, the following applies:
Commodity Discussions
Data about the component is included in a table with format I96. The name of this table is
comprised of the following parameters from the instrument specialties part of the Piping Job
Specification:
MC GS Term(G)_Rat(G) Term(R)_Rat(R) Unnamed_I
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are surface area, empty weight,
weight of water, weight of the actuator plus all those dimensional parameters required to
display the component and its actuator, if any, in the model whose values are not defined in a
generic table.
Unnamed Instrument, GCP=male, RCP=male - If the component is unnamed, if both green
and red connect point data appears in the definition of the component in the instrument
specialties part of the Piping Job Specification and both the green and the red connect points
are male termination types, the following applies:
Data about the component is included in a table with format I91. The name of this table is
comprised of the following parameters from the instrument specialties part of the Piping Job
Specification:
MC GS Term(G) Term(R) Unnamed_I
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are surface area, empty weight,
weight of water, weight of the actuator plus all those dimensional parameters required to
display the component and its actuator, if any, in the model whose values are not defined in a
generic table.
Unnamed Instrument, GCP=male, RCP male - If the component is unnamed, if both green
and red connect point data appears in the definition of the component in the instrument
specialties part of the Piping Job Specification, the green connect point is a male termination
type and the red connect point is not a male termination type, the following applies:
Data about the component is included in a table with format I97. The name of this table is
comprised of the following parameters from the instrument specialties part of the Piping Job
Specification:
MC_GS_Term(G) Term(R) Rat(R) Unnamed_I
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are surface area, empty weight,
weight of water, weight of the actuator plus all those dimensional parameters required to
display the component and its actuator, if any, in the model whose values are not defined in a
generic table.
Relief devices will have actuators unless otherwise specifically indicated in paragraphs that
follow. Actuators are defined independent of the components unless otherwise specifically
indicated in paragraphs that follow. Refer to paragraph C.6.1 for additional requirements
regarding actuators.
Relief devices and their actuators will not be automatically placed during automatic
component placement. They will always be positioned by the User.
Reference to ends in component type definitions that follow refer to the applicable of in-line or
tap ends that might apply to the component.
Under the description of each table format applicable to each component type, the GCP and
RCP rating and schedule/thickness that needs to be provided in the Piping Job Specification
has been listed. These values are required for one or more of the reasons indicated below and
will not necessarily be part of the names of the tables that include data about the component.
To procure the component.
189
Commodity Discussions
To access data tables. Refer to section Model Graphics Definitions for a description of the
table formats.
To supply data required for stress analysis purposes.
The following general comments apply to the use of symbols used to depict these
instruments:
The symbols shown below under each instrument type are only suggested symbols that
can be used to depict such instruments. Any instrument symbol defined in Paragraphs
C5.2, C5.3, C5.4 or C5.5 may be used instead.
Ensure that for each symbol used, a proper match has been to an Isogen symbol.
Unless specifically defined otherwise, symbols listed below have been defined so that
they can be placed either with or without actuators.
Taps may be placed during the design session as required to define connections whose
definition is not possible with the symbol chosen.
The AABBCC code for relief devices will consist of the applicable AABB code, 7P2C, followed by
two numbers for the specific device.
190
Commodity Discussions
191
Commodity Discussions
It is possible either to insert these instrument components in the pipeline in which they belong with
the system breaking the line graphics as required (the system will rotate the instrument
component as dictated by the orientation of the line in which it is to be inserted); or to place these
components in free space and then pipe to them.
Other in-line instruments will not be included in the piping materials class of the line in which
placed. They are independent of piping materials class.
See Also
Named or Unnamed Instruments (on page 192)
Connect Point Data (on page 193)
7P3C01, Balloon instr (in-line) (on page 196)
7P3C02, Restriction orif union (in-line) (on page 196)
7P3C03, Valve w/restriction orif (in-line) (on page 196)
7P3C04, Orif plate (in-line) (on page 196)
7P3C05, Orif plate & flanges (in-line) (on page 196)
7P3C06, Orif plate, flanges & meter run (in-line) (on page 197)
7P3C09, Orif plate & qk chnge fitting (in-line) (on page 197)
7P3C10, Orif pl, qk chnge fitting & met run (in-line) (on page 197)
7P3C13, Venturi tube (in-line) (on page 197)
7P3C16, In-line averaging pitot tube (in-line) (on page 197)
7P3C19, Flow nozzle (in-line) (on page 197)
7P3C22, Var area flow instr (in-line) (on page 198)
7P3C23, Var area flow instr w/upstr reg (in-line) (on page 198)
7P3C24, Var area flow instr w/dwnstr reg (in-line) (on page 198)
7P3C25, Var area flow instr w/upstr vlv (in-line) (on page 198)
7P3C26, Var area flow instr w/dwnstr vlv (in-line) (on page 198)
7P3C29, Pos displacement flow instr (in-line) (on page 198)
7P3C30, Pos displ flow instr w/dwnstr reg (in-line) (on page 199)
7P3C33, In-line target flow instr (in-line) (on page 199)
7P3C35, In-line propeller flow instr (in-line) (on page 199)
7P3C37, Vortex flow instr (in-line) (on page 199)
7P3C39, In-line magnetic flow instr (in-line) (on page 199)
7P3C41, In-line ultrasonic flow instr (in-line) (on page 199)
7P3C44, Flume (in-line) (on page 200)
7P3C46, Weir (in-line) (on page 200)
7P3C48, Segmental wedge (in-line) (on page 200)
7P3C50, Flow straightening vane (in-line) (on page 200)
7P3C53, Trap (in-line) (on page 200)
7P3C56, Vent silencer (in-line) (on page 201)
7P3C57, In-line silencer (in-line) (on page 201)
192
Commodity Discussions
AABBCC code. An AABBCC code may be considered as a generic code about which a more
detailed definition is made in the Piping Job Specification. Depending upon the
circumstances:
One or more model codes may be assigned to one AABBCC code, or
The same model code may be assigned to different AABBCC codes.
The system will first search for dimensional data about the other in-line instrument in the
Instrument TDB. In this search, the system will try to match the component number of the other
in-line instrument with the tag number assigned to it in the Instrument TDB. If dimensional data
about the component is found, the system will assume the component to be named and will
proceed to retrieve dimensional data about it.
If either the component or dimensional data about it is not found, the system will conclude that the
component is unnamed and will then search for it in the piping specialties part of the Piping Job
Specification by its AABBCC code, option and pertinent size range and will proceed to retrieve
applicable data about it.
One of the items retrieved from either the Instrument TDB or the Piping Job Specification is the
model code, which will include the definition of the graphic representation of the component in the
piping model.
193
Commodity Discussions
The only independent variable in this table is the nominal diameter of the green connect point
of the component. The dependent variables are surface area, empty weight, weight of water
plus all those dimensional parameters required to display the component in the model whose
values are not defined in a generic table.
If the component is unnamed, if only green connect point data appears in the definition of the
component in the instrument specialties part of the Piping Job Specification and if the connect
point is not a male termination type, the following applies:
Data about the component is included in a table with format I85. The name of this table is
comprised of the following parameters from the instrument specialties part of the Piping Job
Specification:
MC GS Term(G) Rat(G) Unnamed_I
The only independent variable in this table is the nominal diameter of the green connect point
of the component. The dependent variables are surface area, empty weight, weight of water
plus all those dimensional parameters required to display the component in the model whose
values are not defined in a generic table.
If the component is unnamed, if both green and red connect point data appears in the
definition of the component in the instrument specialties part of the Piping Job Specification,
the green connect point is either a bolted or a female termination type and the red connect
point is a male termination type, the following applies:
Data about the component is included in a table with format I95. The name of this table is
comprised of the following parameters from the instrument specialties part of the Piping Job
Specification:
MC GS Term(G)_Rat(G) Term(R)_Unnamed_I
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are surface area, empty weight,
weight of water plus all those dimensional parameters required to display the component in
the model whose values are not defined in a generic table.
If the component is unnamed, if both green and red connect point data appears in the
definition of the component in the instrument specialties part of the Piping Job Specification
and neither the green nor the red connect points are male termination types, the following
applies:
Data about the component is included in a table with format I96. The name of this table is
comprised of the following parameters from the instrument specialties part of the Piping Job
Specification:
MC GS Term(G)_Rat(G) Term(R)_Rat(R) Unnamed_I
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are surface area, empty weight,
weight of water plus all those dimensional parameters required to display the component in
the model whose values are not defined in a generic table.
If the component is unnamed, if both green and red connect point data appears in the
definition of the component in the instrument specialties part of the Piping Job Specification
and both the green and the red connect points are male termination types, the following
applies:
Data about the component is included in a table with format I91. The name of this table is
comprised of the following parameters from the instrument specialties part of the Piping Job
Specification:
MC GS Term(G) Term(R) Unnamed_I
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are surface area, empty weight,
194
Commodity Discussions
weight of water plus all those dimensional parameters required to display the component in
the model whose values are not defined in a generic table.
If the component is unnamed, if both green and red connect point data appears in the
definition of the component in the instrument specialties part of the Piping Job Specification,
the green connect point is a male termination type and the red connect point is not a male
termination type, the following applies:
Data about the component is included in a table with format I97. The name of this table is
comprised of the following parameters from the instrument specialties part of the Piping Job
Specification:
MC_GS_Term(G) Term(R) Rat(R) Unnamed_I
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are surface area, empty weight,
weight of water plus all those dimensional parameters required to display the component in
the model whose values are not defined in a generic table.
Other in-line instruments will have not have actuators.
Other in-line instruments will not be automatically placed during automatic component placement.
They will always be positioned by the User.
Reference to ends in component type definitions that follow refer to the applicable of in-line or tap
ends that might apply to the component.
Under the description of each table format applicable to each component type, the GCP and RCP
rating and schedule/thickness that needs to be provided in the Piping Job Specification has been
listed. These values are required for one or more of the reasons indicated below and will not
necessarily be part of the names of the tables that include data about the component.
To procure the component.
To access data tables. Refer to Model Graphics Definitions for a description of the table
formats.
To supply data required for stress analysis purposes.
The following general comments apply to the use of symbols used to depict these
instruments:
The symbols shown below under each instrument type are only suggested symbols that
can be used to depict such instruments. Any instrument symbol defined in Paragraphs
C5.2, C5.3, C5.4 or C5.5 may be used instead.
Ensure that for each symbol used, a proper match has been to an Isogen symbol.
Unless specifically defined otherwise, symbols listed below have been defined so that
they can be placed either with or without actuators.
Taps may be placed during the design session as required to define connections whose
definition is not possible with the symbol chosen.
The AABBCC code for other in-line instruments consists of the applicable AABB code, 7P3C,
followed by two numbers for the specific instrument.
195
Commodity Discussions
196
Commodity Discussions
197
Commodity Discussions
198
Commodity Discussions
199
Commodity Discussions
200
Commodity Discussions
See Also
Named or Unnamed Instruments (on page 203)
Connect Point Data (on page 203)
7Q4D01, Discrete [field mounted AE (off-line) (on page 206)
7Q4D02, Discrete [field mounted] AP (off-line) (on page 206)
7Q4D03, Discrete [field mounted] AT (off-line) (on page 206)
7Q4D06, Discrete [field mounted] FC (off-line) (on page 206)
7Q4D07, Discrete [field mounted] FI (off-line) (on page 206)
7Q4D08, Discrete [field mounted] FIC (off-line) (on page 206)
7Q4D09, Discrete [field mounted] FP (off-line) (on page 207)
7Q4D10, Discrete [field mounted] FR (off-line) (on page 207)
7Q4D11, Discrete [field mounted] FRC (off-line) (on page 207)
7Q4D12, Discrete [field mounted] FSH (off-line) (on page 207)
7Q4D13, Discrete [field mounted] FSL (off-line) (on page 207)
7Q4D14, Discrete [field mounted] FSM (off-line) (on page 207)
7Q4D15, Discrete [field mounted] FSHH (off-line) (on page 208)
201
Commodity Discussions
7Q4D16, Discrete [field mounted] FSHL (off-line) (on page 208)
7Q4D17, Discrete [field mounted] FSLL (off-line) (on page 208)
7Q4D18, Discrete [field mounted] FT (off-line) (on page 208)
7Q4D21, Discrete [field mounted] LC (off-line) (on page 208)
7Q4D22, Discrete [field mounted] LG (off-line) (on page 209)
7Q4D23, Discrete [field mounted] LI (off-line) (on page 209)
7Q4D24, Discrete [field mounted] LIC (off-line) (on page 209)
7Q4D25, Discrete [field mounted] LR (off-line) (on page 210)
7Q4D26, Discrete [field mounted] LRC (off-line) (on page 210)
7Q4D27, Discrete [field mounted] LSH (off-line) (on page 210)
7Q4D28, Discrete [field mounted] LSL (off-line) (on page 210)
7Q4D29, Discrete [field mounted] LSM (off-line) (on page 210)
7Q4D30, Discrete [field mounted] LSHH (off-line) (on page 211)
7Q4D31, Discrete [field mounted] LSHL (off-line) (on page 211)
7Q4D32, Discrete [field mounted] LSLL (off-line) (on page 211)
7Q4D33, Discrete [field mounted] LT (off-line) (on page 211)
7Q4D35, Discrete [field mounted] PC (off-line) (on page 212)
7Q4D36, Discrete [field mounted] PDIC (off-line) (on page 212)
7Q4D37, Discrete [field mounted] PDSH (off-line) (on page 212)
7Q4D38, Discrete [field mounted] PDSL (off-line) (on page 212)
7Q4D39, Discrete [field mounted] PDT (off-line) (on page 212)
7Q4D40, Discrete [field mounted] PI (off-line) (on page 212)
7Q4D41, Discrete [field mounted] PIC (off-line) (on page 213)
7Q4D42, Discrete [field mounted] PP (off-line) (on page 213)
7Q4D43, Discrete [field mounted] PR (off-line) (on page 213)
7Q4D44, Discrete [field mounted] PRC (off-line) (on page 213)
7Q4D45, Discrete [field mounted] PSH (off-line) (on page 213)
7Q4D46, Discrete [field mounted] PSL (off-line) (on page 213)
7Q4D47, Discrete [field mounted] PSM (off-line) (on page 214)
7Q4D48, Discrete [field mounted] PSHH (off-line) (on page 214)
7Q4D49, Discrete [field mounted] PSHL (off-line) (on page 214)
7Q4D50, Discrete [field mounted] PSLL (off-line) (on page 214)
7Q4D51, Discrete [field mounted] PT (off-line) (on page 214)
7Q4D53, [Field mounted] pilot light (off-line) (on page 214)
7Q4D57, Discrete single-funct, [field mounted] instr (off-line) (on page 215)
7Q4D58, Discrete multi-funct, [field mounted] instr (off-line) (on page 215)
7Q4D60, Pilot light [accessible in primary location] (off-line) (on page 215)
7Q4D65, Discrete single-funct instr [accessible in primary location] (on page 215)
7Q4D66, Discrete multi-funct instr [accessible in primary location] (on page 215)
7Q4D70, Discrete single-funct instr [inaccessible in primary location] (off-line) (on page 215)
7Q4D71, Discrete multi-funct instr (on page 216)
7Q4D75, [2-way] solenoid valve [field mounted] (off-line) (on page 216)
7Q4D76, [2-way] angle solenoid valve [field mounted] (off-line) (on page 216)
7Q4D77, 3-way solenoid valve [field mounted] (off-line) (on page 216)
7Q4D78, 4-way single solenoid valve [field mounted] (off-line) (on page 216)
7Q4D79, 4-way double solenoid valve [field mounted] (off-line) (on page 216)
7Q4D80, Pilot light (on page 216)
7Q4D85, Discrete single-funct instr (on page 217)
7Q4D86, Discrete multi-funct instr (on page 217)
7Q4D88, Single port pitot tube [field mounted] (off-line) (on page 217)
7Q4D89, Pitot-venturi tube [field mounted] (off-line) (on page 217)
7Q4D90, Off-line averaging pitot tube [field mounted] (off-line) (on page 217)
7Q4D92, Off-line target flow instr [field mounted] (off-line) (on page 217)
202
Commodity Discussions
7Q4D93, Off-line propeller flow instr [field mounted] (off-line) (on page 218)
7Q4D94, Off-line magnetic flow instr [field mounted] (off-line) (on page 218)
7Q4D95, Off-line ultrasonic flow instr [field mounted] (off-line) (on page 218)
7Q4D97, Discrete single-funct instr (on page 218)
7Q4D98, Discrete multi-funct instr (on page 218)
203
Commodity Discussions
If the termination type of the ends differ, regardless of the values for schedule/thickness,
the properties of the end(s) with the lowest codelist number defining its CP preparation
have been defined under the green connect point data.
If the termination type of the ends are the same but the values for rating, schedule or
thickness differ, the properties of the stronger ends(s) have been defined under the green
connect point data.
For each off-line instrument, dimensional data is defined in tables, as follows:
If the component is named, regardless of its other characteristics, the following applies:
Both generic and specific data about the component is included in the applicable unit of
the Instrument TDB.
Refer to the explanation given under table format I80 for details.
If the component is unnamed, if only green connect point data appears in the definition of the
component in the instrument specialties part of the Piping Job Specification and if the connect
point is a male termination type, the following applies:
Data about the component is included in a table with format I81. The name of this table is
comprised of the following parameters from the instrument specialties part of the Piping Job
Specification:
MC GS Term(G) Unnamed_I
204
The only independent variable in this table is the nominal diameter of the green connect point
of the component. The dependent variables are surface area, empty weight, weight of water
plus all those dimensional parameters required to display the component in the model whose
values are not defined in a generic table.
If the component is unnamed, if only green connect point data appears in the definition of the
component in the instrument specialties part of the Piping Job Specification and if the connect
point is not a male termination type, the following applies:
Data about the component is included in a table with format I85. The name of this table is
comprised of the following parameters from the instrument specialties part of the Piping Job
Specification:
MC GS Term(G) Rat(G) Unnamed_I
The only independent variable in this table is the nominal diameter of the green connect point
of the component. The dependent variables are surface area, empty weight, weight of water
plus all those dimensional parameters required to display the component in the model whose
values are not defined in a generic table.
If the component is unnamed, if both green and red connect point data appears in the
definition of the component in the instrument specialties part of the Piping Job Specification,
the green connect point is either a bolted or a female termination type and the red connect
point is a male termination type, the following applies:
Data about the component is included in a table with format I95. The name of this table is
comprised of the following parameters from the instrument specialties part of the Piping Job
Specification:
MC GS Term(G)_Rat(G) Term(R)_Unnamed_I
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are surface area, empty weight,
weight of water plus all those dimensional parameters required to display the component in
the model whose values are not defined in a generic table.
If the component is unnamed, if both green and red connect point data appears in the
definition of the component in the instrument specialties part of the Piping Job Specification
and neither the green nor the red connect points are male termination types, the following
applies:
Commodity Discussions
Data about the component is included in a table with format I96. The name of this table is
comprised of the following parameters from the instrument specialties part of the Piping Job
Specification:
MC GS Term(G)_Rat(G) Term(R)_Rat(R) Unnamed_I
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are surface area, empty weight,
weight of water plus all those dimensional parameters required to display the component in
the model whose values are not defined in a generic table.
If the component is unnamed, if both green and red connect point data appears in the
definition of the component in the instrument specialties part of the Piping Job Specification
and both the green and the red connect points are male termination types, the following
applies:
Data about the component is included in a table with format I91. The name of this table is
comprised of the following parameters from the instrument specialties part of the Piping Job
Specification:
MC GS Term(G) Term(R) Unnamed_I
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are surface area, empty weight,
weight of water plus all those dimensional parameters required to display the component in
the model whose values are not defined in a generic table.
If the component is unnamed, if both green and red connect point data appears in the
definition of the component in the instrument specialties part of the Piping Job Specification,
the green connect point is a male termination type and the red connect point is not a male
termination type, the following applies:
Data about the component is included in a table with format I97. The name of this table is
comprised of the following parameters from the instrument specialties part of the Piping Job
Specification:
MC_GS_Term(G) Term(R) Rat(R) Unnamed_I
The independent variables in this table are the nominal diameters of the green and red
connect points of the component. The dependent variables are surface area, empty weight,
weight of water plus all those dimensional parameters required to display the component in
the model whose values are not defined in a generic table.
Off-line instruments will have not have actuators.
Off-line instruments will not be automatically placed during automatic component placement.
They will always be positioned by the User.
Reference to ends in component type definitions that follow refer to the applicable of in-line or tap
ends that might apply to the component.
Under the description of each table format applicable to each component type, the GCP and RCP
rating and schedule/thickness that needs to be provided in the Piping Job Specification has been
listed. These values are required for one or more of the reasons indicated below and will not
necessarily be part of the names of the tables that include data about the component.
To procure the component.
To access data tables. Refer to Section 4, Model Graphics Definitions, for a description of
the table formats.
The following general comments apply to the use of symbols used to depict these
instruments:
The symbols shown below under each instrument type are only suggested symbols that
can be used to depict such instruments. Any instrument symbol defined in Paragraphs
C5.2, C5.3, C5.4 or C5.5 may be used instead.
205
Commodity Discussions
Ensure that for each symbol used, a proper match has been to an Isogen symbol.
Unless specifically defined otherwise, symbols listed below have been defined so that
they can only be placed either without actuators.
Taps may be placed during the design session as required to define connections whose
definition is not possible with the symbol chosen.
The AABBCC code for off-line instruments will consist of the applicable AABB code, 7Q4D,
followed by two numbers for the specific instrument.
206
Commodity Discussions
207
Commodity Discussions
208
Commodity Discussions
209
Commodity Discussions
210
Commodity Discussions
211
Commodity Discussions
212
Commodity Discussions
213
Commodity Discussions
214
Commodity Discussions
215
Commodity Discussions
216
Commodity Discussions
217
Commodity Discussions
Miscellaneous
See Also
Valve Operators and Actuators (on page 219)
Piping Connectors (on page 228)
218
Commodity Discussions
Number to be Added
219
Commodity Discussions
Chainwheel
1000
Floor stand
2000
Extension stem
3000
For example, if a chainwheel is added to a gear operated valve having an operator model
code of OP_25, the model code for the new operator is A_1025.
For symbol names, by using the symbol whose value is hardcoded in the definition of the
applicable model code.
Data for operators/actuators is defined in tables, as follows:
For piping valves in the piping commodities part of the Piping Job Specification and whose
operator types are less than or equal to 24, dimensional data about the operator, regardless of
whether only GCP or both GCP and RCP data applies to the valve, is included in a table with
format P31A. The name of this table is comprised of the following parameters from the piping
commodities part of the Piping Job Specification:
MC_Type(G)_Rat(G) Op A
Where,
MC applies to the valve to which the operator belongs
Type will have the following possible values:
Preparation
Type
2-199
BLT
300-399
MAL
400-599
FEM
Op represents the absolute value of the entry for operator type made in the "Mod" column of
the Piping Materials Class.
The independent variable(s) in this table is:
For operator types 1-3 and 5-24: the nominal diameter of the green connect point of the
operator.
For operator type 4: the nominal diameters of the "green and of the red connect points of
the operator.
The dependent variables are those dimensional parameters required to display the valve
operator in the model. For these operators, no definition is made of the location of their
center of gravity.
If columns available in the above table were insufficient to allow definition of all the applicable
dimensional parameters, the remaining parameters are included in a table with format P31B.
The name of the P31B table is comprised of the following parameters from the piping
commodities part of the Piping Job Specification:
MC_Type(G)_Rat(G) Op B
220
The only independent variable in this table is the nominal diameter of the green connect point
of the operator. The dependent variables are those dimensional parameters required to
display the valve operator in the model that were not included in the P31A table.
In general, data in these tables represents the largest dimensions resulting from a comparison
of operators supplied by common USA valve manufacturers.
For piping valves in the piping commodities part of the Piping Job Specification and whose
operator types exceed 24 and are less than or equal to 40, the empty weight of the valve
exclusive of the operator weight, the operator weight, the operator code of the valve operator,
the three parameters that define the location of the center of gravity of the operator and up to
Commodity Discussions
two dimensional parameters required to define the geometry of the valve operator, regardless
of whether only GCP or both GCP and RCP data apply to the valve, is included in a table with
format P60A. The name of this table is comprised of the following parameter from the piping
commodities part of the Piping Job Specification:
Cmdty Code_WOPD_A
The only independent variable in this table is the nominal diameter of the green connect point
of the component. The dependent variables are the empty weight of the valve exclusive of
the operator weight, the operator weight, the operator code of the valve operators, the three
parameters that define the location of the center of gravity of the operator and up to two
dimensional parameters required to define the geometry of the valve operator.
If columns available in the above table were insufficient to allow definition of all the applicable
dimensional parameters of the valve operator, the remaining parameters is included in a table
with format P60B. The name of the P60B table is comprised of the following parameter from
the piping commodities part of the Piping Job Specification:
Cmdty Code_WOPD_B
The only independent variable in this table is the nominal diameter of the green connect point
of the component. The dependent variables are those dimensional parameters required to
display the valve operator in the model that were not included in the P60A table.
In general, data in these tables represent the dimensions applicable to the valve described in
the corresponding short description. You should check these tables to make sure that
dimensions given are suitable to the project for which they are intended.
For piping valves in the piping specialties part of the Piping Job Specification whose operator
types exceed 40 and for all instrument valves, all applicable data about the valve, the operator
weight, the operator code (parameter Y1), the three parameters that define the location of the
center of gravity of the operator and all the dimensional parameters required to define the
geometry of the valve operator, regardless of whether only GCP or both GCP and RCP data
apply to the valve, is included in a table with format P80 for piping valves or I80 for instrument
valves. The name of this table is:
Named_Pipe_Specialties, for piping valves
Named_Instr_Specialties, for instrument valves
The only independent variable in this table is the component number of the component. The
dependent variables is all the applicable data about the valve, the operator weight, the
operator code (parameter Y1), the three parameters that define the location of the center of
gravity of the operator and all the dimensional parameters required to define the geometry of
the valve operator.
If at placement time, data was not found in the applicable of the tables defined above, the system
will prompt you for the values of all the parameters that would otherwise be found in the data table.
At this time, a tutorial defining the applicable parameters is displayed. The values you define
are be stored by the system for use in subsequent model reconstruction. The values so stored
will not be used in future model reconstructions after the applicable data tables are prepared.
Valve operators will not be automatically placed during automatic component placement. They
will always be positioned by you.
In the list that follows, types 2-24 apply to operators for piping commodity valves whose
dimensions are determined from tables whose names are formed from attributes in the Piping Job
Specification. Types 25-40 apply to operators for piping commodity valves whose dimensions
are determined from tables whose names depend on the commodity codes for the valves. Types
41-99 apply to operators/actuators for piping and instrument specialty valves.
221
Commodity Discussions
Operators with Data Derived from Parameters in the Applicable Piping Materials Class, 2-24:
Type 03, Handwheel (OT=3), (OC=3), (MC=OP_3, A_1003, A_2003 & A_3003), (SN=OP3,
A1003, S2003 & S3003) (TNF=P31A)
This operator may be placed with or without appurtenances. The default placement is without
appurtenances and is represented by symbol OP3. At any time after placement, the you can add
any one of the appurtenances indicated in the table below by executing the placement command
listed in it. This will cause the existing operator to be deleted and a new operator to be created
whose shape is represented by the symbol listed in the table.
Appurtenance
Placement Command
Symbol
None
Default
OP3
Chainwheel
Add Chainwheel
A1003
Floor stand
Add Floorstand
S2003
Extension stem
Add Extension Stem
S3003
In response to one of the add appurtenance commands, the system will prompt the you for
user-defined information applicable to the indicated appurtenance, as follows:
Appurtenance
Data Prompted
Chainwheel
Total length of chain
Floorstand
"Y1", "Y2", "Y3", "Y4"
Extension stem
"Y1", "Y2"
Further action by the system will depend upon the type of appurtenance involved, as follows:
For chainwheels: the data table that applies to symbol OP3 is used for the definition of the
A1003 symbol. The value for chainwheel height required by symbol A1003 is determined by
the system on the basis of instructions given in note 64.
For floorstands and extension stems: no data table will apply. You are prompted to provide
all the information required to place the symbol involved.
All parameters you provide in the definition of operator appurtenances are remembered by the
system for use during model reconstruction.
It is possible to include in the iso and in reports data required for the purchase of operator
appurtenances. The reports will include, in addition to all the parameters you provide at
placement time, the following data about the valve: the applicable line number, piping materials
class, nominal diameter, commodity code and the three applicable coordinates locating the valve
origin in the model.
Type 04, Handwheel if GCP > RCP (OT=4), (OC=4), (MC=OP_4), (SN=OP4 (TNF=P31A)
This operator is identical in all respects 0o the one described under Type 03, except that:
The table that is used to store the operator dimensions has both the GCP and the RCP
diameters as input. This operator is used for components such as extended body olet valves
whose definition require different values for the diameters of the GCP and RCP.
No data provisions have been made to allow the placement of appurtenances, such as
chainwheels, on this operator.
Type 05, Handwheel, inclined (OT=5), (OC=5), (MC=OP_5, EA_1005), (SN=OP5, A1005)
(TNF=P31A)
This operator may be placed with or without appurtenances. The default placement is without
appurtenances and is represented by symbol OP5. At any time after placement, you can any one
of the appurtenances indicated in the table below by executing the placement command listed in
it. This will cause the existing operator to be deleted and a new operator to be created whose
shape is represented by the symbol listed in the table.
Appurtenance
Placement Command
Symbol
None
Default
OP5
Chainwheel
Add Chainwheel
A1005
222
Commodity Discussions
In response to one of the add appurtenance commands, the system will prompt you for
user-defined information applicable to the indicated appurtenance, as follows:
Appurtenance
Data Prompted
Chainwheel
Total length of chain
Further action by the system will depend upon the type of appurtenance involved, as follows:
For chainwheels: the data table that applies to symbol OP5 is used for the definition of the
A1005 symbol. The value for chainwheel height required by symbol A1005 is determined by
the system on the basis of instructions given in note 64.
All parameters you provide in the definition of operator appurtenances are remembered by the
system for use during model reconstruction.
It is possible to include in the iso and in reports data required for the purchase of operator
appurtenances. The reports will include, in addition to all the parameters you provide at
placement time, the following data about the valve: the applicable line number, piping materials
class, nominal diameter, commodity code and the three applicable coordinates locating the valve
origin in the model.
Type 09, Wrench, short (OT=9), (OC=9), (MC=OP_9), (SN=OP9), (TNF=P31A)
Type 11, Wrench, long (OT=11), (OC=11), (MC=OP_11), (SN=OP9), (TNF=P31A)
Type 17, Lever (OT=17), (OC=17), (MC=OP_17), (SN=OP9), (TNF=P31A)
Type 19, T-handle, short (OT=19), (OC=19), (MC=OP_19, A_2019 & A_3019), (SN=OP9,
S2003 & S3003) (TNF=P31A)
This operator may be placed with or without appurtenances. The default placement is without
appurtenances and is represented by symbol OP9. At any time after placement, you can add any
one of the appurtenances indicated in the table below by executing the placement command listed
in it. This will cause the existing operator to be deleted and a new operator to be created whose
shape is represented by the symbol listed in the table.
Appurtenance
Placement Command
Symbol
None
Default
OP9
Floor stand
Add Floorstand
S2003
Extension stem
Add Extension Stem
S3003
In response to one of the add appurtenance commands, the system will prompt you for
user-defined information applicable to the indicated appurtenance, as follows:
Appurtenance
Data Prompted
Floorstand
"Y1", "Y2", "Y3", "Y4"
Extension stem
"Y1", "Y2"
Further action by the system will depend upon the type of appurtenance involved, as follows:
For floorstands and extension stems: no data table will apply. You are prompted to provide
all the information required to place the symbol involved.
All parameters you provide in the definition of operator appurtenances are remembered by the
system for use during model reconstruction.
It is possible to include in the iso and in reports data required for the purchase of operator
appurtenances. The reports will include, in addition to all the parameters you provide at
placement time, the following data about the valve: the applicable line number, piping materials
class, nominal diameter, commodity code and the three applicable coordinates locating the valve
origin in the model.
Type 21, T-handle, long (OT=21), (OC=21), (MC=OP_21, A_2021 & A_3021), (SN=OP9,
S2003 & S3003) (TNF=P31A)
This operator may be placed with or without appurtenances. The default placement is without
appurtenances and is represented by symbol OP9. At any time after placement, you can add any
223
Commodity Discussions
one of the appurtenances indicated in the table below by executing the placement command
listed in it. This will cause the existing operator to be deleted and a new operator to be created
whose shape is represented by the symbol listed in the table.
Appurtenance
Placement Command
Symbol
None
Default
OP9
Floor stand
Add Floorstand
S2003
Extension stem
Add Extension Stem
S3003
In response to one of the add appurtenance commands, the system will prompt you for
user-defined information applicable to the indicated appurtenance, as follows:
Appurtenance
Data Prompted
Floorstand
"Y1", "Y2", "Y3", "Y4"
Extension stem
"Y1", "Y2"
Further action by the system will depend upon the type of appurtenance involved, as follows:
For floorstands and extension stems: no data table will apply. You are prompted to provide
all the information required to place the symbol involved.
All parameters you provide in the definition of operator appurtenances are remembered by the
system for use during model reconstruction.
It is possible to include in the iso and in reports data required for the purchase of operator
appurtenances. The reports will include, in addition to all the parameters you provide at
placement time, the following data about the valve: the applicable line number, piping materials
class, nominal diameter, commodity code and the three applicable coordinates locating the valve
origin in the model.
Operators with Data Derived from the Commodity Codes of the Valves to Which They Apply,
25-40
Type 25, Handwheel, special (TNF=P60A & P60B)
Handwheel, special type 1 (OT=25), (OC=251), (MC=OP_25, A_1025, A_2025 & A_3025),
(SN=OP_251, A1251, S2003 & S3003)
This operator can be placed with or without appurtenances. The default placement is without
appurtenances and is represented by symbol OP_251. At any time after placement, the You can
add any one of the appurtenances indicated in the table below by executing the placement
command listed in it. This will cause the existing operator to be deleted and a new operator to be
created whose shape is represented by the symbol listed in the table.
Appurtenance
Placement Command
Symbol
None
Default
OP_251
Chainwheel
Add Chainwheel
A1251
Floor stand
Add Floorstand
S2003
Extension stem
Add Extension Stem
S3003
In response to one of the add appurtenance commands, the system will prompt you for
user-defined information applicable to the indicated appurtenance, as follows:
Appurtenance
Data Prompted
Chainwheel
Total length of chain
Floorstand
"Y1", "Y2", "Y3", "Y4"
Extension stem
"Y1", "Y2"
Further action by the system will depend upon the type of appurtenance involved, as follows:
For chainwheels: the data table that applies to symbol OP_251 is used for the definition of
the A1251 symbol. The value for chainwheel height required by symbol A1251 is determined
by the system on the basis of instructions given in note 64.
224
Commodity Discussions
For floorstands and extension stems: no data table will apply. You are prompted to provide
all the information required to place the symbol involved.
All parameters you provide in the definition of operator appurtenances are remembered by the
system for use during model reconstruction.
It is possible to include in the iso and in reports data required for the purchase of operator
appurtenances. The reports will include, in addition to all the parameters you provide at
placement time, the following data about the valve: the applicable line number, piping materials
class, nominal diameter, commodity code and the three applicable coordinates locating the valve
origin in the model.
Type 27, Wrench, special (TNF=P60A & P60B)
Wrench, special type 1 (OT=27), (OC=271), (MC=OP_27), (SN=OP_271)
Type 29, Gear, top mounted handwheel (TNF=P60A & P60B)
Gear, top mounted handwheel type 1 (OT=29), (OC=291), (MC=OP_29), (SN=OP_291)
Gear, top mounted handwheel type 2 (OT=29), (OC=292), (MC=OP_29), (SN=OP_292)
Type 31, Gear, top mounted inclined handwheel (TNF=P60A & P60B)
Gear, top mounted inclined handwheel type 1 (OT=31), (OC=311), (MC=OP_31),
(SN=OP_311)
Type 33, Gear, side mounted handwheel (TNF=P60A & P60B)
Gear, side mounted handwheel type 1 (OT=33), (OC=331), (MC=OP_33, A_1033),
(SN=OP_331, A1331)
This operator may be placed with or without appurtenances. The default placement is without
appurtenances and is represented by symbol OP_331. At any time after placement, you can add
the appurtenance indicated in the table below by executing the placement command listed in it.
This will cause the existing operator to be deleted and a new operator to be created whose shape
is represented by the symbol listed in the table.
Appurtenance
Placement Command
Symbol
None
Default
OP_331
Chainwheel
Add Chainwheel
A1331
In response to the add appurtenance command, the system will prompt you for the following
user-defined information:
Appurtenance
Data Prompted
Chainwheel
Total length of chain
Further action by the system will depend upon the type of appurtenance involved, as follows:
For chainwheels: the data table that applies to symbol OP_331 is used for the definition of
the A1331 symbol. The value for chainwheel height required by symbol A1331 is determined
by the system on the basis of instructions given in note 64.
All parameters you provide in the definition of operator appurtenances are remembered by the
system for use during model reconstruction.
It is possible to include in the iso and in reports data required for the purchase of operator
appurtenances. The reports will include, in addition to all the parameters you provide at
placement time, the following data about the valve: the applicable line number, piping materials
class, nominal diameter, commodity code and the three applicable coordinates locating the valve
origin in the model.
Gear, side mounted handwheel type 2 (OT=33), (OC=332), (MC=OP_33, A_1033), (SN=OP_332,
A1332)
This operator may be placed with or without appurtenances. The default placement is without
appurtenances and is represented by symbol OP_332. At any time after placement, you can add
the appurtenance indicated in the table below by executing the listed placement command. This
225
Commodity Discussions
will cause the existing operator to be deleted and a new operator to be created whose shape is
represented by the symbol listed in the table.
Appurtenance
Placement Command
Symbol
None
Default
OP_332
Chainwheel
Add Chainwheel
A1332
In response to the add appurtenance command, the system will prompt you for the following
user-defined information:
Appurtenance
Data Prompted
Chainwheel
Total length of chain
Further action by the system will depend upon the type of appurtenance involved, as follows:
For chainwheels: the data table that applies to symbol OP_332 is used for the definition of
the A1332 symbol. The value for chainwheel height required by symbol A1332 is determined
by the system on the basis of instructions given in note 64.
All parameters you provide in the definition of operator appurtenances are remembered by the
system for use during model reconstruction.
It is possible to include in the iso and in reports data required for the purchase of operator
appurtenances. The reports will include, in addition to all the parameters you provide at
placement, the following data about the valve: the applicable line number, piping materials class,
nominal diameter, commodity code and the three applicable coordinates locating the valve origin
in the model.
Gear, side mounted handwheel type 3 (OT=33), (OC=333), (MC=OP_33), (SN=OP_333)
Gear, side mounted handwheel type 4 (OT=33), (OC=334), (MC=OP_33), (SN=OP_334)
Type 35, Gear, side mounted inclined handwheel (TNF=P60A & P60B)
Gear, side mounted inclined handwheel type 1 (OT=35), (OC=351), (MC=OP_35),
(SN=OP_351)
Type 39, Lever, quick-action (TNF=P60A & P60B)
Lever, quick-action type 1 (OT=39), (OC=391), (MC=OP_39), (SN=OP_391)
Type 40, Post indicator (TNF=P60A)
Post indicator type 1 (OT=40), (OC=401), (MC=OP_40), (SN=OP_401)
For post indicators, the system will first prompt you for the value of parameter "Y6". It will then
proceed to read from the applicable data table the rest of the parameters required to place the
operator.
It is possible to include in the description of the valve to which this operator applies the value of
"Y6" you define. Actuators, 41-99
Type 41, Diaphragm (TNF=P8*, P9*, I8* or I9*)
Diaphragm type 1, no offset (OC=411), (MC=OP_411), (SN=OP_411)
Diaphragm type 2, no offset, inclined (OC=412), (MC=OP_412), (SN=OP_412)
Diaphragm type 3, with horizontal offset (OC=413), (MC=OP_413), (SN=OP_413)
Type 43, Press-balanced diaphragm (TNF=P8*, P9*, I8* or I9*)
Press-balanced diaphragm type 1, no offset (OC=431), (MC=OP_431), (SN=OP_411)
Press-balanced diaphragm type 2, no offset, inclined (OC=432), (MC=OP_432),
(SN=OP_412)
Press-balanced diaphragm type 3, with horizontal offset (OC=433), (MC=OP_433),
(SN=OP_413)
Type 45, Regulator (TNF=P8*, P9*, I8* or I9*)
Regulator type 1 (OC=451), (MC=OP_451), (SN=OP_451)
226
Commodity Discussions
Regulator type 2 (OC=452), (MC=OP_452), (SN=OP_452)
Regulator type 3 (OC=453), (MC=OP_453), (SN=OP_453)
Type 49, Single acting cylinder (TNF=P8*, P9*, I8* or I9*) Single acting cylinder type 1
(OC=491), (MC=OP_491), (SN=OP_491)
Single acting cylinder type 2, inclined (OC=492), (MC=OP_492), (SN=OP_492)
Single acting cylinder type 3, w/vane and optional cylinder (OC=493), (MC=OP_493),
(SN=OP_493)
Single acting cylinder type 4, camflex (OC=494), (MC=OP_494), (SN=OP_494)
Type 51, Double acting cylinder (TNF=P8*, P9*, I8* or I9*)
Double acting cylinder type 1 (OC=511), (MC=OP_511), (SN=OP_491)
Double acting cylinder type 2, inclined (OC=512), (MC=OP_512), (SN=OP_492)
Double acting cylinder type 3, w/vane and optional cylinder (OC=513), (MC=OP_513),
(SN=OP_493)
Type 53, Pilot operated cylinder (TNF=P8*, P9*, I8* or I9*)
Pilot operated cylinder type 1 (OC=531), (MC=OP_531), (SN=OP_491)
Pilot operated cylinder type 2, inclined (OC=532), (MC=OP_532), (SN=OP_492)
Pilot operated cylinder type 3, w/vane and optional cylinder (OC=533), (MC=OP_533),
(SN=OP_493)
Pilot operated cylinder type 4 (OC=534), (MC=OP_534), (SN=OP_494)
Type 57, Motor (TNF=P8*, P9*, I8* or I9*)
Motor type 1 (OC=571), (MC=OP_571), (SN=OP_571)
Motor type 2 inclined (OC=572), (MC=OP_572), (SN=OP_572)
Motor type 3 (OC=573), (MC=OP_573), (SN=OP_573)
Motor type 4, inclined (OC=574), (MC=OP_574), (SN=OP_574)
Type 61, Digital (TNF=P8*, P9*, I8* or I9*)
Digital type 1 (OC=611), (MC=OP_611), (SN=OP_571)
Type 65, Electro-hydraulic (TNF=P8*, P9*, I8* or I9*)
Electro-hydraulic type 1 (OC=651), (MC=OP_651), (SN=OP_494)
Electro-hydraulic type 2 (OC=652), (MC=OP_652), (SN=OP_571)
Type 69, Single solenoid
This is not a valve actuator. It is an accessory to another actuator. The addition of this item to
an actuator would graphically be covered by the applicable actuator.
Type 71, Single solenoid w/reset
This is not a valve actuator. It is an accessory to another actuator. The addition of this item to
an actuator would graphically be covered by the applicable actuator.
Type 73, Double solenoid
This is not a valve actuator. It is an accessory to another actuator. The addition of this item to
an actuator would graphically be covered by the applicable actuator.
Type 77, Pilot
This is not a valve actuator. It is an accessory to another actuator. The addition of this item to
an actuator would graphically be covered by the applicable actuator.
Type 81, Weight (TNF=P8*, P9*, I8* or I9*)
Weight type 1 (OC=811), (MC=OP_811), (SN=OP_811)
Type 85, Manual (TNF=P8*, P9*, I8* or I9*)
227
Commodity Discussions
Manual type 1 (OC=851), (MC=OP_851), (SN=OP_851)
Manual type 2, inclined (OC=852), (MC=OP_852), (SN=OP_852)
Manual type 3 (OC=853), (MC=OP_853), (SN=OP_853)
Manual type 4, inclined (OC=854), (MC=OP_854), (SN=OP_854)
Type 89, Spring (TNF=P8*, P9*, I8* or I9*)
Spring type 1 (OC=891), (MC=OP_891), (SN=OP_491)
Type 91, Capacitance sensor
This is not a valve actuator. It is an accessory to another actuator. The addition of this item to
an actuator would graphically be covered by the applicable actuator.
Type 93, Ball float (TNF=P8*, P9*, I8* or I9*)
No graphic symbol has been provided to represent this actuator.
Type 95, Displacement float
This is not a valve actuator. It is actually part of a level displacement transmitter which would
be shown with a balloon on the model.
Type 97, Paddle wheel
This is not a valve actuator. Should be only shown in the model by an instrument balloon.
Nothing would be modeled for this component.
Piping Connectors
See Also
Piping Utility Connector (6R9E) (on page 228)
Off-volume Piping Connectors (6R9G) (on page 228)
Off-Site Piping Connectors (6R9H) (on page 229)
228
Commodity Discussions
229
Commodity Discussions
See section titled "Choosing a Branch Connection from a Branches Table" for details.
If a "1" is entered in such column, the system is to prompt for dimensions. If dimensions
are provided by the user, their values are stored in the TDB so that in subsequent
recreations of the piping system, those values and not those that might exist in a data
table are used by the system.
Data defined for these components will allow the system to determine the applicable stress
intensification factors (SIF) to be used in stress analysis of the piping system.
The thickness of the portion of piping from PCP2 of this component to the centerline of the
header is reported as "RIGID" to the Pipe Stress Analysis software, regardless of the value in
the Piping Job Specification so as not to provide a fictitious flexibility.
The empty weight of these components is neglected.
Assemblies
See Also
In-line Piping Macrocomponents (6N8C) (on page 230)
On-line Piping Macrocomponents (6P8C) (on page 230)
230
Vent/drain
Vent/drain
Vent/drain
Vent/drain
Connection
Connection
Connection
Connection
Connection
Connection
Connection
Connection
detail
detail
detail
detail
detail
detail
detail
detail
detail
detail
detail
detail
1
2
3
H
1
2
3
4
5
6
7
8
(on-line)
(on-line)
(on-line)
(on-line)
(on-line)
(on-line)
(on-line)
(on-line)
(on-line)
(on-line)
(on-line)
(on-line)
(macrocomponent)
(macrocomponent)
(macrocomponent)
(macrocomponent)
(macrocomponent)
(macrocomponent)
(macrocomponent)
(macrocomponent)
(macrocomponent)
(macrocomponent)
(macrocomponent)
(macrocomponent)
APPENDIX C
Symbols
In This Appendix
Piping Commodity Symbols ........................................................... 231
Fire and Safety Symbols ................................................................ 313
Piping Specialty Symbols .............................................................. 323
Instrument Specialty Symbols ....................................................... 333
Miscellaneous Symbols ................................................................. 349
Bio-Pharmaceutical SpecificationComponent Symbols ................ 371
Bio-Pharmaceutical Operators ...................................................... 401
Bio-Pharmaceutical Specialty Components .................................. 403
Details Assumed ............................................................................ 407
Piping and Instrument Symbol Notes ............................................ 425
Assembly Notes ............................................................................. 432
231
Symbols
232
Symbols
233
Symbols
234
Symbols
235
Symbols
236
Symbols
237
Symbols
238
Symbols
239
Symbols
240
Symbols
241
Symbols
242
Symbols
243
Symbols
244
Symbols
245
Symbols
246
Symbols
247
Symbols
248
Symbols
249
Symbols
250
Symbols
251
Symbols
252
Symbols
253
Symbols
254
Symbols
255
Symbols
256
Symbols
257
Symbols
258
Symbols
259
Symbols
260
Symbols
261
Symbols
262
Symbols
263
Symbols
264
Symbols
265
Symbols
266
Symbols
267
Symbols
268
Symbols
269
Symbols
270
Symbols
271
Symbols
272
Symbols
273
Symbols
274
Symbols
275
Symbols
276
Symbols
277
Symbols
278
Symbols
279
Symbols
280
Symbols
281
Symbols
282
Symbols
283
Symbols
284
Symbols
285
Symbols
286
Symbols
287
Symbols
288
Symbols
289
Symbols
290
Symbols
291
Symbols
292
Symbols
293
Symbols
294
Symbols
295
Symbols
296
Symbols
297
Symbols
298
Symbols
299
Symbols
300
Symbols
301
Symbols
302
Symbols
303
Symbols
304
Symbols
305
Symbols
306
Symbols
307
Symbols
308
Symbols
309
Symbols
310
Symbols
311
Symbols
312
Symbols
313
Symbols
314
Symbols
315
Symbols
316
Symbols
317
Symbols
318
Symbols
319
Symbols
320
Symbols
321
Symbols
322
Symbols
323
Symbols
324
Symbols
325
Symbols
326
Symbols
327
Symbols
328
Symbols
329
Symbols
330
Symbols
331
Symbols
332
Symbols
333
Symbols
334
Symbols
335
Symbols
336
Symbols
337
Symbols
338
Symbols
339
Symbols
340
Symbols
341
Symbols
342
Symbols
343
Symbols
344
Symbols
345
Symbols
346
Symbols
347
Symbols
348
Symbols
Miscellaneous Symbols
Miscellaneous Symbol OP3
349
Symbols
350
Symbols
351
Symbols
352
Symbols
353
Symbols
354
Symbols
355
Symbols
356
Symbols
357
Symbols
358
Symbols
359
Symbols
360
Symbols
361
Symbols
362
Symbols
363
Symbols
364
Symbols
365
Symbols
366
Symbols
367
Symbols
368
Symbols
369
Symbols
370
Symbols
Bio-Pharmaceutical SpecificationComponent
Symbols
Bio-Pharm Specification Component Symbol FERR
371
Symbols
372
Symbols
373
Symbols
374
Symbols
375
Symbols
376
Symbols
377
Symbols
378
Symbols
379
Symbols
380
Symbols
381
Symbols
382
Symbols
383
Symbols
384
Symbols
385
Symbols
386
Symbols
387
Symbols
388
Symbols
389
Symbols
390
Symbols
391
Symbols
392
Symbols
393
Symbols
394
Symbols
395
Symbols
396
Symbols
397
Symbols
398
Symbols
399
Symbols
The symbol below shows a non-symmetrical valve where DIMENSION_1 is not equal to
DIMENSION_2. The distance between the Center (CP0) and Connect Point 2 (CP2) is
represented by DIM_2/2.
400
Symbols
Bio-Pharmaceutical Operators
Bio-Pharm Operator Symbol SOP_3
401
Symbols
402
Symbols
403
Symbols
404
Symbols
405
Symbols
406
Symbols
Details Assumed
Detail V1
407
Symbols
Detail V2
Detail V3
408
Symbols
Detail V4
Detail V5
409
Symbols
Detail V7
Detail V8
410
Symbols
Detail H1
Detail H2
411
Symbols
Detail H3
Detail H4
412
Symbols
Detail F1
Detail F2
413
Symbols
Detail F4
Detail F7
414
Symbols
Detail F8
Detail P1
415
Symbols
Detail P2
Detail P3
416
Symbols
Detail P4
Detail P5
417
Symbols
Detail P7
Detail P8
418
Symbols
Detail P9
Detail T1
419
Symbols
Detail T
Detail T4
420
Symbols
Detail L1
Detail L2
421
Symbols
Detail L4
422
Symbols
Detail L7
423
Symbols
Detail L8
424
Symbols
7.
8.
9.
10.
For all female ends: a distance "Q" from the actual outermost surface of the component.
The origin of the component will be located mid-way between PCP1 and PCP2 for two
connect point components and in the center of the component for single connect point
components.
It is not required to retrieve values for surface area, empty weight and water weight for this
component.
The origin of the component will be located mid-way between PCP1 and the outermost most
surface of the component at the end opposite PCP1.
This will be a vertical cylinder whose nominal pipe diameter will be equal to the nominal pipe
diameter of the valve.
This parameter will have a value equal to the applicable of "A", "E" or "P2" times the factor
indicated below:
Nominal Pipe Diameter Range
Factor
2 and smaller
0.50
2.01-10
0.55
10.01 and larger
0.60
11. The combined height of these cones will equal the nominal pipe diameter of the valve.
The value for the base of each of the cones will equal the applicable of "A" or "E" times the
factor indicated below:
Nominal Pipe Diameter Range
Factor
2 and smaller
0.40
2.01-10
0.45
10.01 and larger
0.50
12.
13.
14.
15.
16.
The value of this parameter will equal the nominal pipe diameter of the valve divided by 2.
The length of this cylinder will be a minimum.
Four equally spaced concentric rings will be provided.
This parameter will equal 1.2 times the value of dimension "O".
This parameter will have a value equal to the applicable parameter "E" times the factor
indicated below:
Nominal Pipe Diameter Range
Factor
0.5 and smaller
0.90
425
Symbols
0.51-2.00
2.01 and larger
0.75
0.60
17. This parameter will have a value equal to the applicable parameter "E" times the factor
indicated below:
Nominal Pipe Diameter Range
Factor
0.5 and smaller
0.25
0.51-2.00
0.20
2.01 and larger
0.12
18. For components all whose ends are either bolted or female end types and that require a
dimension from the male termination type generic table, the system will use the table
corresponding to table suffix "5".
19. This parameter will have a value equal to the applicable parameter "L" times the factor
indicated below:
Nominal Pipe Diameter Range
Factor
0.5 and smaller
0.20
0.51-2.00
0.12
2.01 and larger
0.10
20. The reinforcement will be represented as a 360 degree cylinder concentric with the branch
pipe.
21. The location of PCP2 will be determined by the system so that the point in the OD of the end
cross-section of the branch pipe that is furthest removed from the header centerline will be
located as follows:
For model codes RPAD and RWELD: on the outside surface of the header pipe.
For model codes RPAD2 and RWELD2: on the inside surface of the header pipe.
22. Values for weld length and OD will depend upon the system of units of measure used, as
defined by the specific model code used, as follows:
Model Code
Weld Length
Weld OD
BWELD
0.0625"
P + 0.0625"
BWELD1
By Others
By Others
BWELD2
By Others
By Others
23. Parameter "P4" will define the space occupied by the valve disk in the open position. Its sign
will be positive (+) if in the direction of the secondary axis of the orientation tee or negative (-)
if opposite to it.
24. You define the dimensional or orientation parameters listed below during the design session,
following the system prompts. The values so entered will be used during model
reconstruction. Labels may be prepared to display this value on the iso and/or in the iso
materials listing.
Symbol Name
Tutorial Name
Parameter
FS1A
FS1A
D1
FS2B
FS2B
D5
FS10A
FS10A
D3, D9
FS11A
FS11A
D3, D9
FS13A
FS13A
D3, D9
25. For SN=FS2B, the parallelepiped defined by parameters "D8", "D9" and "D10" will rotate,
together with the nozzle, by the specified angle D14, with due regards to sign.
26. This symbol applies to cubical components that have one of their axis oriented along the
direction of the primary axis of the coordinate system for the component. The origin of the
component will be located at the intersection of its diagonals. It will be possible to place
components to which this symbol applies either by their origin or by PCP1. The tertiary axis of
426
Symbols
27.
28.
29.
30.
31.
32.
33.
34.
the component is defined as that axis which follows the direction of the thumb of the right hand
when the other fingers of the right hand are curled in the direction following the path from the
positive end of the primary axis of the component to the positive end of the secondary axis of
the component. The output parameters which are specific to this symbol are defined as
follows:
Output D1 - defines the vectorial distance from the origin of the component to PCP1 along the
direction of the primary axis of the component. Its sign will be positive if the vector is in the
direction of the primary axis of the component and negative if it is opposite to the direction of
the primary axis of the component.
Output D2 - defines the vectorial distance from the origin of the component to PCP1 along the
direction of the secondary axis of the component. Its sign will be positive if the vector is in the
direction of the secondary axis of the component and negative if it is opposite to the direction
of the secondary axis of the component.
Output D3 - defines the vectorial distance from the origin of the component to PCP1 along the
direction of the tertiary axis of the component. Its sign will be positive if the vector is in the
direction of the tertiary axis of the component and negative if it is opposite to the direction of
the tertiary axis of the component.
Output D4 - defines the length of the component along the direction of the primary axis of the
component. Its sign will always be positive.
Output D5 - defines the length of the component along the direction of the secondary axis of
the component. Its sign will always be positive.
Output D6 - defines the dimension of the component along the direction of the tertiary axis of
the component. Its sign will always be positive.
The nominal pipe diameter of PCP1 refers to the header size.
The value for angle B and/or for "angle" will be intrinsic to the component being placed, unless
it is stated in Appendix B that it is to be determined by the system from data contained in the
design file.
You will first identify the PCP of the elbow that will determine the centerline direction of the
elbolet, as defined by the primary axis of the orientation tee of the elbow PCP. When
placement of an elbolet is involved, the system will always place PCP2 of the elbolet pointing
away from the elbow, regarless of the direction in which the orientation tee points. The
system will then place a temporary PCP at the intersection of the primary axis of the
orientation tee with the outside of the elbow. This temporary PCP will then be moved inside
the elbow by a fixed amount to ensure that the connection between the elbolet and the elbow
will not "leak". The "moved" PCP will become PCP1 for the elbolet. The system will then
place PCP2 for the elbolet using the "M" dimension from the data table.
Dimension "N" will be equal to the branch (RCP) outside diameter "P" plus "2K".
The value for parameter "M" will be provided in the "Mod" column of the Piping Job
Specification. It will not be stored in any data table.
This dimension will be equal to "1.5P".
The value of "N" may be positive or negative, depending upon the type of end being defined.
If the value of "N" is <=0, the system will not draw a cylinder to represent the female end
socket.
The origin of the section describing this component will be located at the intersection of the
plane containing the axis of flow for the component with the planes at the ends of the
component, as follows:
For bolted ends: the plane passing through the back of the bolted end.
For male and female ends: the plane passing through the corresponding connect point.
427
Symbols
35. The origin of the section describing this component will be located at the intersection of the
plane containing the axis of flow for the component with the planes at the ends of the
component, as follows:
For bolted ends: not applicable.
For male or female ends: the plane passing through a point located inward from the
corresponding connect point "end distance" "K" or "L", if applicable.
36. For pipe bends, the radius of the torous for this component will be the nominal pipe diameter
of the component times the value included in the "Mod" column of the Piping Job
Specification.
For all other applicable components, the radius of the torous will be determined from the
equations listed below:
For bolted ends: [A - R] [tan Y/2]
For male ends: [E - K] [tan Y/2]
For female ends: [E - K] [tan Y/2]
37.
38.
39.
40.
41.
42.
43. Values have been provided for parameter "O" per the following formula:
T= T-API-590 - CA-API-590 + CA + FA, rounded to the next 1/16th inch
where,
T-API-590 - is the applicable blank thickness defined in API-590.
CA-API-590 - is the applicable blank corrosion allowance defined in API-590.
CA - is 0.125 inch for geometry standards API-590Z1 or AITKEN Z1; 0.25 inch for geometry
standards API-590Z2 or AITKEN Z2.
FA - is 0.125 inch if RFTBE is involved; 0 inch for all other ends.
44. Provide a cylinder with the following dimensions:
Diameter "P", where "P" is the outside diameter from the applicable generic table.
Length having a value equal to the nominal pipe diameter of the applicable end times the
factor indicated below:
428
Symbols
Nominal Pipe Diameter Range
1 and smaller
1.01-3.50
3.51 and larger
Factor
2.00
1.00
0.50
45. The drain for the component, PCP3, will be located in the plane defined by the primary and
secondary axis of the orientation tee.
46. This parameter will equal the nominal pipe diameter times the factor indicated below:
Nominal Pipe Diameter Range
Factor
3 and smaller
1.25
3.01-10
0.55
10.01 and larger
0.30
47. Model codes and symbols ending in the letter "C", for example S1AC, may be used to
represent piping commodity components. Since the EDEN software does not recognize
"generic" components for piping commodity components, however, the following limitations
apply:
Model codes S1AC, S3AC and S4AC must be defined to have no offset; for example, for
model S1AC, parameters P4 and P5 must be defined to be zero.
For model code S51AC, parameter P7 must be zero.
Model code S64BC does not work at all.
The above limitations do not apply to piping specialty components.
48. This symbol will be used to represent off-line instruments by means of a cylinder. The
following comments will apply:
The applicability of this representation will be defined by you, making the proper menu
selection at placement time. It will be remembered by the system during reconstruction of
the model.
Several identical model codes have been provided (I301iT or I301iS, where i=A-J) to allow
definition of up to 2000 instruments of the same AABBCC code.
No access to a data table will be required when this representation applies. If values are
not entered for P2 and P3, they will be defaulted to "minimum" and "6 inches" respectively.
49. Output P1 defines the total number of connect points applicable to the component. If the
number entered in this field is less than the number of connect points shown pictorially in the
sketch for the applicable symbol, only the number of connect points entered for this parameter
will apply.
50. Output P1 defines the total number of connect points applicable to the component. The
number entered for this parameter must agree with the number of connect points shown
pictorially in the sketch for the applicable symbol.
51. The following note applies to operators with chainwheels:
The diameter of the chainwheel will be assumed to be equal to that of the corresponding
handwheel.
The value for the chainwheel height (CW Height) will be determined by the software as a
function of the corresponding handhweel diameter (HW Diam), as follows:
HW Diam
CW Height
=<6.000
(0.33333)(HW Diam)
>6.000, =<42.000
3.0
>42.000
(0.07143)(HW Diam)
52. During reconstruction of the model, the system will automatically place the operator with the
dimensions and in the orientation defined by you during initial placement. For piping
429
Symbols
53.
54.
55.
56.
57.
58.
59. The optional capability will be provided to define, for stress analysis purposes, the weight of
the operator and the location of the center of gravity of the operator weight. The location of
the center of gravity is defined by parameters "Y1", "Y2" and "Y3". The weight of the
430
Symbols
component itself, exclusive of the operator, will still be defined as part of the component's
table. The operator data will be retrieved as part of the data transfer to the pipe stress
analysis program taking into full consideration the orientation and rotation made of the
operator at placement time.
60. If there is no stem extension above the top of the gear operator, define the parameter
identified below as "0.0". Never define such
parameter as "-".
Symbol Name
Parameter
OP_291
Y10
OP_292
Y13
OP_311
Y10
OP_331
Y11
OP_332
Y13
OP_333
Y12
OP_334
Y12
OP_351
Y12
61.
62.
63.
64.
For data tables that are prepared without this parameter, the EDEN symbol will assume that
no stem extension applies.
The dimensions for gear operators shown on data tables were obtained in the following
manner: from the fully open valve stem dimension stated in the catalog we subtracted the
valve nominal pipe diameter to account for the stem free travel. We then added the flange
adaptor height, as advised by the Manufacturer, and the height of the gear operator, from
catalog dimensions.
The angle that the secondary axis of the auxiliary orientation tee makes in its final position
with its default position is required for the purchase of the valve and must be supplied by the
system to the materials control function.
For this operator, the center of gravity of the valve operator will always be located along the
operator stem. The values of "Y2" and "Y3" will always be "-" in the corresponding operator
data table.
The dimensional or orientation parameters listed below will be defined by you from the design
session, upon prompting by the system. The values so entered will be used during model
reconstruction. Labels may be prepared to display this value on the iso and/or in the iso
materials listing.
Symbol Name
Tutorial Name
Parameter(s)
OP_333
ZO333D
Y11
OP_334
ZO334D
Y11
OP_401
ZO401D
Y6
65. During placement of this operator, the tutorial listed below will be displayed for you to select
the orientation of the handwheel.
Symbol Name
Tutorial Name
OP_331
ZO331O
OP_332
ZO331O
OP_333
ZO331O
OP_334
ZO331O
OP_351
ZO331O
66. Parameter "Y1" will be the operator type and will be only listed in the applicable actuator data
table.
67. The optional capability will be provided to define, for stress analysis purposes, the weight of
the actuator and the location of the center of gravity of the actuator weight. The location of
the center of gravity is defined by parameters "Y2", "Y3" and "Y4". The weight of the
431
Symbols
component itself, exclusive of the actuator, will still be defined as part of the component's
table. The actuator data will be retrieved as part of the data transfer to the pipe stress
analysis program taking into full consideration the orientation and rotation made of the
actuator at placement time.
68. For this actuator, the center of gravity of the valve actuator will always be located along the
actuator stem. The values of "Y3" and "Y4" will always be "-" in the corresponding actuator
data table.
Assembly Notes
1. For a vent/drain connection off a pipe run, the system will place the appropriate branch
reinforcement component on the basis of data in the applicable branch reinforcement table.
For a vent/drain connection off equipment item, a piping component or an instrument
component, you must select the proper component to which the vent drain assembly will be
connected. This may require defining a nozzle in an item of equipment or placing a tap on a
piping component.
2. The characteristics of this branch nipple and of the flange mating the vent/drain valve, if
applicable, will be as follows:
If the CP of the vent/drain valve that is nearest the pipe run has an end preparation type in the
range from 10 through 81, as defined by codelist set CL330, the following will apply:
If the pipe run is not insulated, the following applies:
If the end preparation of the CP of the branch component that applies to the assembly
is in the range from 10 through 81, as defined by codelist set CL330, no branch nipple
nor vent/drain valve mating flange will be required. The vent/drain valve will be
bolted directly to the flange of the branch.
If the end preparation of the CP of the branch component that applies to the assembly
is 301, as defined by codelist set CL330, no branch nipple will be required. The
flange that mates the vent/drain valve will be chosen to have a RCP with end
preparation 301 and will be connected directly to the assembly end of the branch
component.
If the end preparation of the CP of the branch component that applies to the assembly
is 421 or 441, as defined by codelist set CL330, a 4 inch long branch nipple will be
required. If end preparation 421 is involved, applicable AABBCC and option codes
for the branch nipple will be 6Q3C88 and 728 respectively. If end preparation 441 is
involved, applicable AABBCC and option codes for the branch nipple will be 6Q3C88
and 727 respectively. The flange that mates the vent/drain valve will be chosen to
have a RCP with end preparation to suit that of the assembly end of the branch
component (421 or 441) and will be connected directly to the assembly end of the
branch nipple.
If the end preparation of the CP of the branch component that applies to the assembly
is other than defined above, an error message will be returned by the system when
use of this assembly is attempted.
If the pipe run is insulated, the following applies:
If the end preparation of the CP of the branch component that applies to the assembly
is in the range from 10 through 81, as defined by codelist set CL330, no branch nipple
nor vent/drain valve mating flange will be required. The vent/drain valve will be
bolted directly to the flange of the branch.
432
Symbols
If the end preparation of the CP of the branch component that applies to the assembly
is 301, 421 or 441, as defined by codelist set CL330, a branch nipple will be provided
with nominal length defined by the following equation:
L= 1 + P/2 + T + W_i - B - N
where, L - is the nominal length required for the branch nipple
1 - is one inch
P/2 - is half the outside pipe diameter as derived from table MAL_Term_TS for the
pipe run.
T - is the insulation thickness of the pipe run as derived from the TDB
W_i - is the nut allowance as derived from the applicable of the tables described
below
STUD_Rat_TS, if the RDB option that involves CP termination for bolt length calculations
is not active;
OR
STUD_Term_Rat_TS, if the RDB option that involves CP termination for bolt length
calculations is active that applies to the bolts used by the vent/drain valve.
B - is the offset of assembly end of the branch component from the centerline of the pipe
run, derived from the applicable branch component dimension table.
N - is the distance from the back of the flange to CP2 in the flange, as defined in table
MC_GS_Term(G)_Rat(G)_Term(R)_Rat(R)_A that applies to the vent/drain valve.
The nominal length of the branch nipple determined from the above equation will be
rounded to the next full inch length but will be no less than 4 inches long. The end
preparation(s) of the branch nipple will be chosen by the system to suit the end
preparation types of the branch component. If end preparation 301 is involved,
applicable AABBCC and option codes for the branch nipple will be PIPING and 1
respectively. If end preparation 421 is involved, applicable AABBCC and option codes
for the branch nipple will be 6Q3C88 and 728 respectively. If end preparation 441 is
involved, applicable AABBCC and option codes for the branch nipple will be 6Q3C88 and
727 respectively.
The flange that mates the vent/drain valve will be chosen by the system to have a RCP
with end preparation to suit that of the assembly end of the branch component (301, 421
or 441) and will be connected to the branch nipple.
If the end preparation of the CP of the branch component that applies to the assembly is
other than defined above, an error message will be returned by the system when use of
this assembly is attempted.
If the CP of the vent/drain valve which is nearest the pipe run has end preparation type of
either 421 or 441, as defined by codelist set CL330, a branch nipple will be required. The
branch nipple length will be 1 inch longer than the insulation thickness of the pipe run rounded
to the next full inch length but no less than 4 inches long. The end preparations of the branch
nipple will be chosen by the system to suit the end preparation types of the branch component
and of the vent/drain valve. If end preparation 421 is involved, applicable AABBCC and
option codes for the branch nipple will be 6Q3C88 and 728 respectively. If end preparation
441 is involved, applicable AABBCC and option codes for the branch nipple will be 6Q3C88
and 727 respectively.
No flange will be required to mate the vent/drain valve.
433
Symbols
If the CP of the vent/drain valve which is nearest the pipe run has end preparation type other
than in the range from 10-81 or of either 421 or 441, as defined by codelist set CL330, an error
message will be returned by the system when use of this assembly is attempted.
3. If the mating CPs of the valves in the vent/drain assembly have an end preparation other than
421, an error message will be returned by the system when use of this assembly is attempted.
4. If any of the CPs of the valve in the vent/drain assembly have an end preparation other than
401 or if the pipe is insulated beyond 4 inches thickness, an error message will be returned by
the system when use of this assembly is attempted.
434
APPENDIX D
435
436
B GY
B HA
B LA
Flanged elbow
B LB
B VQ
Flanged reducing
elbow
Flanged 45 deg elbow
Flanged concentric
reducer
Flanged eccentric
reducer
Flanged tee
Flanged reducing tee
Flanged return bend
Flanged adapter
THD adapter
LR elbow
45 deg LR elbow
Tee
Elbow
45 deg elbow
Concentric reducer
Reducing tee
Eccentric reducer
Victaulic cap
Reducer FTSE
Coupling, w/gasket
Coupling, w/gasket &
FTE outlet
Coupling, w/gasket &
MTE outlet
Reducing tee, w/ MTE
outlet
Red tee, w/FTE outlet
B WS
B XA
Weld sleeve
Flanged cross
B FY
B GA
B GB
B GC
B GD
B GE
B GF
B GG
B GH
B LC
B RA
B RB
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
TA
TB
UA
VA
VB
VC
VD
VE
VF
VG
VH
VI
VJ
VK
VL
VM
VN
B VO
B VP
'Flanged
elbow'
'Flanged
elbow'
'Flanged
'Flanged
437
YA
YB
ZA
ZB
ZC
ZD
ZE
ZF
ZN
Flanged Y
Flanged 45 deg lateral
Hub
Hub & flanged
Coupling/connector
Clamp
Cap
Flexible coupling
Nipple/connector
B
B
B
B
B
B
B
B
B
B
B
B
B
B
A
B
C
D
E
F
G
K
L
M
N
O
R
S
CL150
CL300
CL400
CL600
CL900
CL1500
CL2500
CL25
CL125
CL250
CL800
CL175
std conn
shrouded bore
connection
CL150
CL300
CL400
CL600
CL900
CL1500
CL2500
CL25
CL125
CL250
CL800
CL175
standard connection
shrouded bore connection
BZ
438
B
B
B
A
B
D
FFFE
RFFE
RFFE 125 Ra finish
B
B
B
J
L
M
RJFE
flange
flange
socket
flange
flange
flange
socket
x socket
x socket x
x socket x
x flange x
B
B
B
B
B
B
B
R
S
T
U
V
W
Z
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
C
D
E
F
G
H
I
J
L
M
N
S
X
Z
A
E
Z
socket x socket x
flange
bell & spigot
SWE
THD
MJE
grooved
welded
S-40
S-80
S-XS
S-160
thk per B16.5
S-XXS
S-100
S-120
S-140
S-LW
S-20
S-30
S-STD
thk per reqn
Sch 40
Sch 80
X-strong
Sch 160
thk per ANSI-B16.5
XX-strong
Sch 100
Sch 120
Sch 140
light-weight
Sch 20
Sch 30
standard-weight
thk per specification ??
B16.1
B16.5
ANSI-B16.1
ANSI-B16.5
ASTM-A234 Gr.WPB
ASTM-A216 Gr.WCB
ASTM-A216 Gr.WCB,
galvanized
carbon steel
ASTM-A105
ASTM-A234 Gr.WPB, Victaulic
ASTM-A234 Gr.WPB,
galvanized, Victaulic
ASTM-A181 Cl.70
ASTM-A181 Cl.70, Barco
BB-41020-??-21
AISI-4140
B
B
B
AAA
AAB
AAC
ASTM-A234-WPB
ASTM-A216-WCB
ASTM-A216-WCB, galv
B
B
B
B
AAE
AAF
AAG
AAH
carbon steel
ASTM-A105
ASTM-A234-WPB
ASTM-A234-WPB
B
B
AAN
AAO
ASTM-A181-70
ASTM-A181-70
AAZ
AISI-4140
439
ABC
EAB
EAC
EEE
FFB
FFC
FFF
FFH
FFL
IAA
ASTM-A53-B, galv
ASTM-A217-C5
ASTM-A217-C12
ASTM-A182-F1
ASTM-A182-F12
ASTM-A182-F11
ASTM-A182-F22
ASTM-A182-F5
ASTM-A182-F9
ASTM-A351-CF8M
B
B
B
B
B
IAB
IIA
IIF
IIG
IIK
IIL
B
B
B
B
IIM
IIN
UAA
WXW
ASTM-A351-CF8C
ASTM-A266-3
ASTM-A182-F316
ASTM-A182-F316L
17-4PH SS,
w/graphite
347 SS, w/graphite
coating
ASTM-A182-F347H
ASTM-A182-F347
ASTM-D2996-RTRP
ASTM-A234-WPBW
WXX
ASTM-A234-WPB
ZAC
ASTM-A536-65-45-12
ZAD
ASTM-A536-65-45-12/E
PDM
ZAE
ZAF
ZAG
ASTM-A536-65-45-12/B
una N
ASTM-A536-65-45-12
ASTM-A536-65-45-12/E
PDM
B
B
B
B
B
B
440
ZAH
ZDE
ZDF
ZDG
ZDM
ZDN
ASTM-A536-65-45-12/B
una N
ASTM-A126-A, galv
ASTM-A126-B, galv
ASTM-A47, galv
ASTM-A395
ASTM-A126-A
Gr.65-45-12,
Victaulic
Gr.65-45-12/EPDM,
Victaulic
ASTM-A536 Gr.65-45-12/Buna
N, galvanized, Victaulic
ASTM-A126 Cl.A, galvanized
ASTM-A126 Cl.B, galvanized
ASTM-A47, galvanized
ASTM-A395, nodular iron
ASTM-A126 Cl.A, 12" &
smaller
ZDO
ASTM-A126-B
Completing Materials
! 0 1 2
! 1 2345678901234567890 SHORT DESCRIPTION LONG DESCRIPTION
! FIRST LETTER: C - COMPLETING MATERIALS (PDS WILL NOT USE)
C AC
C AD
Primer
C AE
C CA
Solvent cement
Protector
Solvent cement
Protector
C
C
C
C
C
Tape
Channel trace
Heat transfer cement
Identification tag
Snap trace
Tape
Channel trace
Heat transfer cement
Identification tag
Snap trace
Chemtrol
Koch
Markad Service Co
Dekoron
Thermon
Thermon TFK-4
Thermon T-80
Chemtrol
Koch
Markad Service Co.
Dekoron
Purple Primer
heavy duty PVC solvent
cement
heavy duty CPVC solvent
cement
galvanized steel
Thermon Channel Trace,
Gr.T-3
Thermon Snap Trace,
Gr.T-63
Thermon Snap Trace,
Extruded
C
C
C
C
C
C
C
C
CB
CH
HT
ID
ST
AAAB
AAAE
DAAB
DCCC
TAAA
TAAB
TAAC
ZZZZ
C
C
AAE
AAF
Purple Primer
heavy duty PVC cement
AAG
C
C
GAA
TAA
galv steel
Thermon Channel Trace
TAB
TAC
ZZZ
Thermon TFK-4
Thermon T-80
441
D BA
D CA
D CB
D DA
D
D
D
D
D
D
@@CL125
@@CL150
CL175
@@300#
@rating per reqn
CL125
CL150
CL175
300#
rating ??
D
D
A
B
@@FFFE
FFFE/FTE
D
D
D
C
D
Z
@@MTE
@@FTE
D
D
D
D
D
D
D
D
442
A
B
C
G
X
Z
A
I
J
S
V
W
X
Z
carbon steel
stainless steel
@@304 SS
brass
ductile iron
cast iron
@@matl per reqn
D
D
D
AA
AB
BA
CA
carbon steel
stainless steel
Type 304 SS
brass
ductile iron
cast iron
matl ??
@@Stang BB0309-21
Stang Model BB0309-21
@@Stang
Stang
@@American Darling B-50-B American Darling
B-50-B
Wirt & Knox V-7
Wirt & Knox V-7
DA
D
D
D
D
EA
AA
AB
BA
BB
BC
BD
BE
BF
DA
DB
@@Grinnell Mulsifyre
Projector S1
Grinnell Fire
Protection, Mulsifyre
Projector S1
@@Powhatan 30-333
Powhatan 30-333
@@
@@ccw open
counterclockwise open
free standing, [427]
free standing, [427]
w/fog nozzle
w/two reaction
supports, w/fog nozzle
supported, [427] w/fog
supported, [427]
nozzle supported, [427] w/fog nozzle
w/fog nozzle
@@free standing, [427]
free standing, [427]
w/shaper tip nozzle
w/two reaction
supports, w/shaper tip
nozzle
@@supported, [427]
supported, [427]
w/shaper tip nozzle
w/shaper tip nozzle
@@free standing w/shaper free standing w/shaper
tip nozzle
tip nozzle
@@free standing w/fog
free standing w/fog
nozzle
nozzle
@@wall mount, rt hand
wall mounted, right
w/hose & fog nozzle
hand w/hose & fog
nozzle
@wall mount, left hand
wall mounted, left
w/hose & fog nozzle
hand w/hose & fog
nozzle
Steam Specialties
! 0 1 2
! 1 2345678901234567890 SHORT DESCRIPTION LONG DESCRIPTION
! FIRST LETTER: E - STEAM SPECIALTIES
E AB
E AD
E BA
E CB
E CD
Thermodynamic steam
E
E
E
E
E
E
AF
AG
AI
AM
AO
AS
443
E CF
E CM
E CS
E ZZ
E
E
E
E
E
E
E
E
E
E
E
E
E
E
CL150
CL300
CL400
CL600
CL900
CL1500
CL2500
CL125
CL250
CL175
CL25
CL50
CL75
E
E
E
A
B
D
E
E
E
E
J
S
T
Z
E
E
E
E
E
E
E
444
A
B
C
D
E
F
G
L
M
O
R
S
T
Z
CL150
CL300
CL400
CL600
CL900
CL1500
CL2500
CL125
CL250
CL175
CL25
CL50
CL75
FFFE
RFFE
RFFE, 125 Ra finish
AA
AB
AC
AD
AE
AF
AG
AH
AI
AJ
AK
AL
AM
AN
AO
AP
AQ
AR
BA
TA
TE
TF
TG
TH
TI
ZZ
AAD
AAE
AAF
AAG
AAH
AAI
AAJ
AAK
AAL
BAA
EAV
EAW
FAA
FAB
ASTM-A105, Armstrong
71-315
ASTM-A105, Spriax Sarco SM
21
ASTM-A105, Armstrong 411F
ASTM-A105, Spirax Sarco PB
43/2
ASTM-A105, Spirax Sarco
SM652
ASTM-A105, ITT Hoffman
TB-6W
ASTM-A105, ITT Hoffman
CFH-TB
ASTM-A105, Armstrong
310FW
ASTM-A105, Armstrong
411G-FW
ASTM-A216 Gr.WCB,
Armstrong 981
ASTM-A182 Gr.F11,
1.25Cr-0.5Mo, Yarway 720
ASME-SA182 Gr.F11,
1.25Cr-0.5Mo, Yarway 720
ASTM-A182 Gr.F11,
1.25Cr-0.5Mo, ITT Hoffman
CH1-TB
ASTM-A182 Gr.F11,
1.25Cr-0.5Mo, ITT Hoffman
CUH3-TB
445
FAC
ASTM-A182-F11, ITT
Hoffman CUH4-TB
FAT
FAV
FAW
GAA
GAB
ASTM-A182-F11, Yarway
515
ASTM-A182-F11, Yarway
740
ASTM-A182-F11, Yarway
710
ASTM-A217-WC9, Yarway
C-500
ASTM-A182-F22,
Armstrong 5155FG
E
E
IAA
IAB
IAC
IAD
ASTM-A240-304L,
Wright-Austin 40EF
SS, Armstrong 2010
ZPA
ZPB
ZPC
ASTM-A278-30, Clark
60F
ASTM-A126-A, Crane
Swartwout
ASTM-A278-30,
Armstrong J Ser LD
Model
ASTM-A182 Gr.F11,
1.25Cr-0.5Mo, ITT Hoffman
CUH4-TB
ASTM-A182 Gr.F11,
1.25Cr-0.5Mo, Yarway 515
ASTM-A182 Gr.F11,
1.25Cr-0.5Mo, Yarway 740
ASTM-A182 Gr.F11,
1.25Cr-0.5Mo, Yarway 710
ASTM-A217 Gr.WC9,
2.25Cr-1Mo, Yarway C-500
ASTM-A182 Gr.F22,
2.25Cr-1Mo, Armstrong
5155FG
SS, Armstrong TT-2000
SS, Armstrong 2011, w/CS
connector
ASTM-A240 Type 304L,
Wright-Austin 40EF
SS, Armstrong 2010, w/CS
connector
ASTM-A278 Cl.30, cast iron,
Clark 60F
ASTM-A126 Cl.A, cast iron,
Crane Swartwout
ASTM-A278 Cl.30, cast iron,
Armstrong J Series LD Model
Flanges
!
!
!
F
F
F
F
F
F
F
F
F
F
F
F
F
446
0 1 2
1 2345678901234567890 SHORT DESCRIPTION LONG DESCRIPTION
FIRST LETTER: F - FLANGES
A
@@Flange, WN
Flange, weld neck
B
@@Blind flange
Blind flange
C
@@Flange, SW
Flange, socketwelded
D
@@Flange, THD
Flange, threaded
E
@@Flange, slip-on
Flange, slip-on
F
@@Flange, lap joint
Flange, lap joint
G
@@Orifice flange, WN
Orifice flange, weld neck
H
SW orifice flange
Socketwelded orifice
flange
I
@@Orifice flange, THD
Orifice flange, threaded
J
Slip-on orifice flange Slip-on orifice flange
L
Long WN flange
Long weld neck flange
M
Solder joint flange
Solder joint flange per
ANSI-B16.24
N
@@Flange, SE
Flange, socket end
R
S
T
U
Red
Red
Red
Red
F V
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
AA
AB
AC
AD
AE
AF
AG
AX
BA
BB
BC
BD
BE
BH
BO
BP
BQ
BR
BS
BT
CA
CB
CD
CE
DA
DB
DC
DD
OA
OB
OC
OD
OE
OF
OG
PB
WN flange
slip-on flange
THD flange
SW flange
Victaulic flange
@@ANSI-B16.5 CL150
@@ANSI-B16.5 CL300
ANSI-B16.5 CL400
@@ANSI-B16.5 CL600
@@ANSI-B16.5 CL900
@@ANSI-B16.5 CL1500
ANSI-B16.5 CL2500
rating per reqn
@@API-605 CL150
@@API-605 CL300
API-605 CL400
API-605 CL600
API-605 CL900
API-605 CL75
API-6A CL2000
API-6A CL3000
API-6A CL5000
API-6A CL10000
API-6A CL15000
API-6A CL20000
@@MSS-SP-44 CL150
@@MSS-SP-44 CL300
@@MSS-SP-44 CL600
MSS-SP-44 CL900
ANSI-B16.1 CL25
ANSI-B16.1 CL125
ANSI-B16.1 CL250
ANSI-B16.1 CL800
ANSI-B16.36 CL150
ANSI-B16.36 CL300
ANSI-B16.36 CL400
ANSI-B16.36 CL600
ANSI-B16.36 CL900
ANSI-B16.36 CL1500
ANSI-B16.36 CL2500
@@ANSI-B16.36 CL300,
ANSI-B16.5 CL150
ANSI-B16.5 CL300
ANSI-B16.5 CL400
ANSI-B16.5 CL600
ANSI-B16.5 CL900
ANSI-B16.5 CL1500
ANSI-B16.5 CL2500
rating ??
API-605 CL150
API-605 CL300
API-605 CL400
API-605 CL600
API-605 CL900
API-605 CL75
API-6A CL2000
API-6A CL3000
API-6A CL5000
API-6A CL10000
API-6A CL15000
API-6A CL20000
MSS-SP-44 CL150
MSS-SP-44 CL300
MSS-SP-44 CL600
MSS-SP-44 CL900
ANSI-B16.1 CL25
ANSI-B16.1 CL125
ANSI-B16.1 CL250
ANSI-B16.1 CL800
ANSI-B16.36 CL150
ANSI-B16.36 CL300
ANSI-B16.36 CL400
ANSI-B16.36 CL600
ANSI-B16.36 CL900
ANSI-B16.36 CL1500
ANSI-B16.36 CL2500
ANSI-B16.36 CL300, 0.5 SWE
447
448
PC
PD
PE
PF
PG
PM
PN
PO
PP
PR
PS
QB
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
SA
SB
SC
SD
SE
SF
SG
SH
SI
TA
TB
TC
TD
TE
TF
TG
ZZ
F
F
F
A
B
D
tap "
ANSI-B16.36 CL400 0.5 SWE
tap "
ANSI-B16.36 CL600, 0.5 SWE
tap "
ANSI-B16.36 CL900 0.5 SWE
tap "
ANSI-B16.36 CL1500 0.5 SWE
tap "
ANSI-B16.36 CL2500 0.5 SWE
tap "
ANSI-B16.36 CL150 0.75 SWE
tap "
ANSI-B16.36 CL300, 0.75
SWE tap "
ANSI-B16.36 CL400 0.75 SWE
tap "
ANSI-B16.36 CL600, 0.75
SWE tap "
ANSI-B16.36 CL1500, 0.75
SWE tap "
ANSI-B16.36 CL2500 0.75
SWE tap "
ANSI-B16.36 CL150, 0.5 FTE
tap "
CL150
CL300
CL400
CL600
CL900
CL1500
CL2500
CL250
CL175
AWWA-C207 Cl.DA
Taylor Forge CL75
Taylor Forge CL125
Taylor Forge CL125LW
Taylor Forge CL175
Taylor Forge CL250
Taylor Forge CL350
@@FFFE
@@RFFE
@@RFFE, 125 Ra finish
F
F
F
J
L
N
125-500 Ra finish
RFFE, 63-250 Ra finish raised face flanged end,
63-250 Ra finish
RFFE, 63-125 Ra finish raised face flanged end,
63-125 Ra finish
RFFE, 125-250 Ra finish raised face flanged end,
125-250 Ra finish
@@RJFE
ring joint flanged end
lens joint
lens joint flanged end
RFFE, 3 Ra finish
raised face flanged end, 3
Ra finish
@@
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
AA
AB
AC
AD
AF
AG
AH
AI
AJ
AK
AL
AM
AN
AO
AW
BA
BB
BC
BD
CA
CB
CC
CD
CE
CF
CG
CH
CI
CJ
CK
CL
S-5S
S-10S
@@S-40S
@@S-80S
S-10
S-20
S-30
S-40
S-60
@@S-80
S-100
S-120
S-140
@@S-160
@@[???]
S-LW
S-STD
S-XS
@@S-XXS
0.125 "
0.188 "
0.25 "
0.312 "
0.375 "
0.438 "
0.5 "
0.562 "
0.625 "
0.688 "
0.75 "
0.812 "
Sch 5S
Sch 10S
Sch 40S
Sch 80S
Sch 10
Sch 20
Sch 30
Sch 40
Sch 60
Sch 80
Sch 100
Sch 120
Sch 140
Sch 160
[???]
light-weight
standard-weight
X-strong
XX-strong
0.125 "
0.188 "
0.25 "
0.312 "
0.375 "
0.438 "
0.5 "
0.562 "
0.625 "
0.688 "
0.75 "
0.812 "
449
450
CM
CN
CO
CP
CQ
CR
CS
CT
CU
CV
CW
CX
DD
EA
VEB
VED
EE
EF
EG
EH
FE
MA
MB
MC
MD
ME
MF
MG
MH
MI
MJ
MK
ML
MM
MN
MO
MP
MQ
MR
MS
MT
MU
0.875 "
0.938 "
1 "
1.062 "
1.125 "
1.188 "
1.25 "
1.375 "
1.5 "
1.625 "
1.75 "
1.875 "
0.281 "
2 "
2.125 "
2.375 "
2.5 "
2.625 "
2.75 "
2.875 "
3.5 "
2.0 mm
2.5 mm
3.0 mm
3.5 mm
4.0 mm
4.5 mm
5.0 mm
6.0 mm
7.0 mm
8.0 mm
10.0 mm
12.0 mm
16.0 mm
20.0 mm
25.0 mm
30.0 mm
35.0 mm
40.0 mm
50.0 mm
60.0 mm
80.0 mm
0.875 "
0.938 "
1 "
1.062 "
1.125 "
1.188 "
1.25 "
1.375 "
1.5 "
1.625 "
1.75 "
1.875 "
0.281 "
2 "
2.125 "
2.375 "
2.5 "
2.625 "
2.75 "
2.875 "
3.5 "
2.0 mm
2.5 mm
3.0 mm
3.5 mm
4.0 mm
4.5 mm
5.0 mm
6.0 mm
7.0 mm
8.0 mm
10.0 mm
12.0 mm
16.0 mm
20.0 mm
25.0 mm
30.0 mm
35.0 mm
40.0 mm
50.0 mm
60.0 mm
80.0 mm
MV
PA
PB
PC
PD
PE
PF
PG
PH
PI
PJ
PK
PL
PM
PN
PO
PP
PQ
PR
PS
PZ
QF
ZZ
100.0 mm
3.2 mm
4.8 mm
6.4 mm
7.9 mm
9.5 mm
11.1 mm
12.7 mm
14.3 mm
15.9 mm
17.5 mm
19.1 mm
20.6 mm
22.2 mm
23.8 mm
25.4 mm
27.0 mm
28.6 mm
30.2 mm
31.8 mm
29.0 mm
26.0 mm
@@
100.0 mm
3.2 mm (0.125")
4.8 mm (0.188")
6.4 mm (0.25")
7.9 mm (0.312")
9.5 mm (0.375")
11.1 mm (0.438")
12.7 mm (0.5")
14.3 mm (0.562")
15.9 mm (0.625")
17.5 mm (0.688")
19.1 mm (0.75")
20.6 mm (0.812")
22.2 mm (0.875")
23.8 mm (0.938")
25.4 mm (1")
27.0 mm (1.062")
28.6 mm (1.125")
30.2 mm (1.188")
31.8 mm (1.25")
29.0 mm (1.142")
26.0 mm
ASTM-A105
ASTM-A105, aluminized
ASTM-A105, treated &
wrapped
ASTM-A105, galvanized
ASTM-A105, aluminized,
treated & wrapped
ASTM-A350 Gr.LF2
ASME-SA105
ASTM-A182 Gr.F12,
1Cr-0.5Mo
ASTM-A182 Gr.F11
ASTM-A182 Gr.F22,
2.25Cr-1Mo
ASTM-A182 Gr.F21,
3Cr-1Mo
ASTM-A182 Gr.F5
ASTM-A182 Gr.F5A,
5Cr-0.5Mo
ASTM-A182 Gr.F7,
7Cr-0.5Mo
F
F
F
AAA
AAB
AAC
@@ASTM-A105
ASTM-A105, alum
ASTM-A105 T&W
F
F
AAH
AAI
@@ASTM-A105, galv
ASTM-A105 alum T&W
F
F
F
ABB
ABE
FFB
@@ASTM-A350-LF2
@@ASME-SA105
ASTM-A182-F12
F
F
FFC
FFF
@@ASTM-A182-F11
ASTM-A182-F22
FFG
ASTM-A182-F21
F
F
FFH
FFI
@@ASTM-A182-F5
ASTM-A182-F5A
FFK
ASTM-A182-F7
451
452
F
F
F
FFL
GFD
GFF
@@ASTM-A182-F9
@@ASME-SA182-F11
ASME-SA182-F22
F
F
F
IIA
IIB
IIC
F
F
F
F
F
F
F
F
F
F
F
F
IIE
IIF
IIG
IIH
IIJ
IIK
IIL
IIN
IIO
IIP
IIY
IJF
@@ASTM-A182-F304
@@ASTM-A182-F304L
ASTM-A182-F316L,
w/0.03% C max
ASTM-A182-F310
@@ASTM-A182-F316
ASTM-A182-F316L
ASME-SA182-F316L
@@ASTM-A182-F321
ASTM-A182-F321H
ASTM-A182-F347
ASTM-A182-F348
ASME-SA182-F316
ASTM-A182-F304H
ASTM-A182-F347H
ASTM-A182-F316L,
special
F
F
F
F
IKA
MLF
NPE
NPF
OAA
ASTM-A451-HF modified
ASTM-A350-LF3
ASTM-B62 bronze
@@ASTM-B166-600, hot
finish
ASTM-B564 Monel
OAC
PAA
ASTM-B462 Alloy 20
TAA
ASTM-F439 CPVC
TAB
@@ASTM-D2467 PVC
WAA
WAB
F
F
WAC
WAD
F
F
WXW
ZAD
@@ASTM-A105, cement
lined
ASTM-A105, cement lined
& epoxy coated
ASTM-A105, epoxy coated
ASTM-A105, cement lined
& T&W
ASTM-A105 epoxy lined
ASTM-A536-65-45-12/EPD
M
ASTM-A182 Gr.F9
ASME-SA182 Gr.F11
ASME-SA182 Gr.F22,
2.25Cr-1Mo
ASTM-A182 Gr.F304
ASTM-A182 Gr.F304L
ASTM-A182 Gr.F316L,
w/0.03% C max
ASTM-A182 Gr.F310
ASTM-A182 Gr.F316
ASTM-A182 Gr.F316L
ASME-SA182 Gr.F316L
ASTM-A182 Gr.F321
ASTM-A182 Gr.F321H
ASTM-A182 Gr.F347
ASTM-A182 Gr.F348
ASME-SA182 Gr.F316
ASTM-A182 Gr.F304H
ASTM-A182 Gr.F347H
ASTM-A182 Gr.F316L,
w/0.036% C max, 12% Ni min,
2.2% Mo min
ASTM-A451 Gr.HF modified
ASTM-A350 Gr.LF3, 3.5 Ni
ASTM-B62 bronze
ASTM-B166 Gr.600 UNS
N06600, hot finish
ASTM-B564 UNS N04400,
Monel
ASTM-B564 UNS NO8800,
Incoloy 800
ASTM-B462 UNS N08020,
Alloy 20
ASTM-F439 Cl.23447-B,
CPVC
ASTM-D2467 Cl.12454-B
PVC
ASTM-A105, cement lined
ASTM-A105, cement lined &
epoxy coated
ASTM-A105, epoxy coated
ASTM-A105, cement lined,
treated & wrapped
ASTM-A105, epoxy lined
ASTM-A536
Gr.65-45-12/EPDM, ductile
iron, Victaulic
ZAE
ASTM-A536-65-45-12/Bun
a N
ZAG
ASTM-A536-65-45-12/EPD
M
ZAH
ASTM-A536-65-45-12/Bun
a N
ASTM-A536
Gr.65-45-12/Buna N,
ductile iron, Victaulic
ASTM-A536
Gr.65-45-12/EPDM, ductile
iron, galvanized,
Victaulic
ASTM-A536
Gr.65-45-12/Buna N,
ductile iron, galvanized,
Victaulic
Flanged Fittings
! 0 1 2
! 1 2345678901234567890 SHORT DESCRIPTION LONG DESCRIPTION
! FIRST LETTER: G - FLANGED FITTINGS
G A
Flange isolation kit
Flange isolation kit
G D
Spacer
Spacer for plastic pipe
G E
@@Paddle spacer
Paddle spacer
G F
Paddle spacer for
Paddle spacer for
maintenance blank
maintenance blank
G G
Bleed ring, w/THD tap Bleed ring, w/threaded
tap
G H
Bleed ring, w/SWE tap Bleed ring,
w/socketwelded end tap
G J
@@Spectacle blank
Spectacle blank
G L
@@Paddle blank
Paddle blank
G M
Maint type paddle
Maintenance type paddle
blank
blank
G N
@@Blank disc
Blank disc
G O
3-bolt blank assy
Three bolt blank
assembly
G P
5-bolt blank assy
Five bolt blank assembly
G Q
7-bolt blank assy
Seven bolt blank
assembly
G U
Union blank
Union blank
G
G
G
G
G
G
G
G
G
A
AB
AC
AD
AE
AF
AG
BA
BB
@@ANSI-B16.5 CL150
ANSI-B16.5 CL300
ANSI-B16.5 CL400
ANSI-B16.5 CL600
ANSI-B16.5 CL900
ANSI-B16.5 CL1500
ANSI-B16.5 CL2500
API-605 CL150
API-605 CL300
ANSI-B16.5 CL150
ANSI-B16.5 CL300
ANSI-B16.5 CL400
ANSI-B16.5 CL600
ANSI-B16.5 CL900
ANSI-B16.5 CL1500
ANSI-B16.5 CL2500
API-605 CL150
API-605 CL300
453
454
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
BC
BD
BE
BH
BO
BP
BQ
BR
BS
BT
CA
CB
CD
DA
DB
DC
DD
FA
FB
FD
API-605 CL400
API-605 CL600
API-605 CL900
API-605 CL75
API-6A CL2000
API-6A CL3000
API-6A CL5000
API-6A CL10000
API-6A CL15000
API-6A CL20000
@@MSS-SP-44 CL150
@@MSS-SP-44 CL300
@@MSS-SP-44 CL600
ANSI-B16.1 CL25
ANSI-B16.1 CL125
ANSI-B16.1 CL250
ANSI-B16.1 CL800
@@API-590 CL150
@@API-590 CL300
@@API-590 CL600
API-605 CL400
API-605 CL600
API-605 CL900
API-605 CL75
API-6A CL2000
API-6A CL3000
API-6A CL5000
API-6A CL10000
API-6A CL15000
API-6A CL20000
MSS-SP-44 CL150
MSS-SP-44 CL300
MSS-SP-44 CL600
ANSI-B16.1 CL25
ANSI-B16.1 CL125
ANSI-B16.1 CL250
ANSI-B16.1 CL800
API-590 CL150
API-590 CL300
API-590 CL600
>
G
G
G
G
FE
FF
FG
GA
>
GB
>
GD
>
GE
>
GF
GG
>
HA
>
HB
>
HD
>
HE
>
HF
HG
@@API-590 CL900
@@API-590 CL1500
API-590 CL2500
@@API-590Z1 CL150,
w/0.125 CA "
@@API-590Z1 CL300,
w/0.125 CA "
@@API-590Z1 CL600,
w/0.125 CA "
@@API-590Z1 CL900,
w/0.125 CA "
@@API-590Z1 CL1500,
w/0.125 CA "
API-590 CL2500,
w/0.125 CA "
@@API-590Z2 CL150,
w/0.25 CA "
@@API-590Z2 CL300,
w/0.25 CA "
@@API-590Z2 CL600,
w/0.25 CA "
@@API-590Z2 CL900,
w/0.25 CA "
@@API-590Z2 CL1500,
w/0.25 CA "
API-590 CL2500, w/0.25
CA "
API-590 CL900
API-590 CL1500
API-590 CL2500
API-590 CL150, w/0.125
corrosion allowance "
API-590 CL300, w/0.125
corrosion allowance "
API-590 CL600, w/0.125
corrosion allowance "
API-590 CL900, w/0.125
corrosion allowance "
API-590 CL1500, w/0.125
corrosion allowance "
API-590 CL2500, w/0.125
CA "
API-590 CL150, w/0.25
corrosion allowance "
API-590 CL300, w/0.25
corrosion allowance "
API-590 CL600, w/0.25
corrosion allowance "
API-590 CL900, w/0.25
corrosion allowance "
API-590 CL1500, w/0.25
corrosion allowance "
API-590 CL2500, w/0.25
CA "
SA
SB
SC
SD
SE
SF
CL150
CL300
CL400
CL600
CL900
CL1500
CL150
CL300
CL400
CL600
CL900
CL1500
G
G
G
G
G
G
G
G
G
G
SG
SH
SI
TA
TB
TC
TD
TE
TF
TG
CL2500
CL250
CL175
AWWA-C207 Cl.E
Taylor Forge CL75
Taylor Forge CL125
Taylor Forge CL125LW
Taylor Forge CL175
Taylor Forge CL250
Taylor Forge CL350
CL2500
CL250
CL175
AWWA-C207 Cl.E
Taylor Forge CL75
Taylor Forge CL125
Taylor Forge CL125LW
Taylor Forge CL175
Taylor Forge CL250
Taylor Forge CL350
FFFE
G
G
B
D
RFFE
RFFE, 125 Ra finish
G
G
G
G
J
M
N
R
G
G
G
G
S
T
W
Z
G
G
G
G
G
G
AA
AB
AC
AD
AF
AG
S-5S
S-10S
S-40S
S-80S
S-10
S-20
Sch
Sch
Sch
Sch
Sch
Sch
5S
10S
40S
80S
10
20
455
456
AH
AI
AJ
AK
AL
AM
AN
AO
AW
BA
BB
BC
BD
CA
CB
CC
CD
CE
CCF
CG
CH
CI
CJ
CK
CL
CM
CN
CO
CP
CQ
CR
CS
DD
MA
MB
MC
MD
ME
MF
MG
MH
MJ
S-30
S-40
S-60
S-80
S-100
S-120
S-140
S-160
[???]|bore to match|
S-LW
S-STD
S-XS
S-XXS
0.125 "
0.188 "
0.25 "
0.312 "
0.375 "
0.438 "
0.5 "
0.562 "
0.625 "
0.688 "
0.75 "
0.812 "
0.875 "
0.938 "
1 "
1.062 "
1.125 "
1.188"
1.25 "
0.281 "
2.0 mm
2.5 mm
3.0 mm
3.5 mm
4.0 mm
4.5 mm
5.0 mm
6.0 mm
8.0 mm
Sch 30
Sch 40
Sch 60
Sch 80
Sch 100
Sch 120
Sch 140
Sch 160
[???]
light-weight
standard-weight
X-strong
XX-strong
0.125 "
0.188 "
0.25 "
0.312 "
0.375 "
0.438 "
0.5 "
0.562 "
0.625 "
0.688 "
0.75 "
0.812 "
0.875 "
0.938 "
1 "
1.062 "
1.125"
1.188"
1.25 "
0.281 "
2.0 mm
2.5 mm
3.0 mm
3.5 mm
4.0 mm
4.5 mm
5.0 mm
6.0 mm
8.0 mm
MK
ML
MM
MN
MO
MP
MQ
MR
MS
MT
MU
MV
PA
PB
PC
PD
PE
PF
PG
PH
PI
PJ
PK
PL
PM
PN
PO
PP
PQ
PR
PS
ZZ
10.0 mm
12.0 mm
16.0 mm
20.0 mm
25.0 mm
30.0 mm
35.0 mm
40.0 mm
50.0 mm
60.0 mm
80.0 mm
100.0 mm
3.2 mm
4.8 mm
6.4 mm
7.9 mm
9.5 mm
11.1 mm
12.7 mm
14.3 mm
15.9 mm
17.5 mm
19.1 mm
20.6 mm
22.2 mm
23.8 mm
25.4 mm
27.0 mm
28.6 mm
30.2 mm
31.8 mm
@@
10.0 mm
12.0 mm
16.0 mm
20.0 mm
25.0 mm
30.0 mm
35.0 mm
40.0 mm
50.0 mm
60.0 mm
80.0 mm
100.0 mm
3.2 mm (0.125) "
4.8 mm (0.188) "
6.4 mm (0.25) "
7.9 mm (0.312) "
9.5 mm (0.375) "
11.1 mm (0.438) "
12.7 mm (0.5) "
14.3 mm (0.562) "
15.9 mm (0.625) "
17.5 mm (0.688) "
19.1 mm (0.75) "
20.6 mm (0.812) "
22.2 mm (0.875) "
23.8 mm (0.938) "
25.4 mm (1) "
27.0 mm (1.062) "
28.6 mm (1.125) "
30.2 mm (1.188) "
31.8 mm (1.25) "
ASTM-A516 Gr.60
ASME-SA516 Gr.60
ASTM-A516 Gr.60, hot dip
galvanized after
fabrication
ASTM-A285 Gr.C
ASTM-A285 Gr.C, hot dip
galvanized to ASTM-A123
ASTM-A515 Gr.70, Mack
Iron
ASTM-A105, w/Teflon
G
G
G
AAA
AAB
AAC
ASTM-A516-60
ASME-SA516-60
ASTM-A516-60, galv
G
G
ABA
ABB
ASTM-A285-C
ASTM-A285-C
ABN
ASTM-A515-70
ABS
ASTM-A105/TFE, galv
457
458
ABT
ABY
G
G
ADA
ADB
ADC
>
G
G
G
ADD
ADE
ADF
>
ADG
AEA
G
G
EAA
FAA
FAB
FAC
FAD
G
G
G
G
FAE
FAF
FAG
GFA
G
G
G
G
G
G
G
G
G
G
GFG
IAA
IIG
IIH
IIJ
IIL
IJA
IJB
IJC
IJD
seals, galvanized,
Greenwood
ASTM-A105/TFE
ASTM-A105, w/Teflon
seals, Greenwood
ASTM-A105/Hycar
ASTM-A105, w/Hycar seals,
Greenwood
@@ASTM-A516-70
ASTM-A516 Gr.70
ASTM-A516-60
ASTM-A516 GR 60, w/0.125
thk Monel clading
ASTM-B127 UNS N04400
@@ASTM-A516-70, galv
ASTM-A516 Gr.70,
galvanized
ASTM-A516-65
ASTM-A516 Gr.65
@@ASME-SA516-70
ASME-SA516 Gr.70
@@ASTM-A516-70,
ASTM-A516 Gr.70, Aitken,
Aitken Z1, w/0.125 CA " w/0.125 corrosion
allowance "
@@ASTM-A516-70,
ASTM-A516 Gr.70, Aitken,
Aitken Z2, w/0.25 CA " w/0.25 corrosion
allowance "
ASTM-A420-WPL6
ASTM-A420 Gr.WPL6, low
temp CS, w/Teflon seals,
Greenwood
ASTM-A204-A
ASTM-A204 Gr.A, C-Mo
ASTM-A387-5 Cl.1
ASTM-A387 Gr.5, Cl.1,
5Cr
ASTM-A387-9 Cl.1
ASTM-A387 Gr.9, Cl.1,
9Cr
ASTM-A387-11 Cl.1
ASTM-A387 Gr.11, Cl.1,
1.25Cr
ASTM-A387-22 Cl.1
ASTM-A387 Gr.22, Cl.1,
2.25Cr
@@ASTM-A387-5 Cl.2
ASTM-A387 Gr.5, Cl.2
@@ASTM-A387-9 Cl.2
ASTM-A387 Gr.9, Cl.2
@@ASTM-A387-11 Cl.2
ASTM-A387 Gr.11, Cl.2
ASME-SA387-11 Cl.1
ASME-SA387 Gr.11, Cl.1,
1.25Cr
@@ASME-SA387-11 Cl.2
ASME-SA387 Gr.11, Cl.2
ASTM-A167-316
ASTM-A167 Type 316
ASTM-A240-316L
ASTM-A240 Type 316L
ASTM-A167-304L
ASTM-A167 Type 304L
ASTM-A167-321
ASTM-A167 Type 321
ASTM-A167-347
ASTM-A167 Type 347
@@ASTM-A240-304
ASTM-A240 Type 304
ASTM-A240-304H
ASTM-A240 Type 304H
@@ASTM-A240-304L
ASTM-A240 Type 304L
@@ASTM-A240-304,
ASTM-A240 Type 304,
Aitken, w/0.125 CA "
Aitken, w/0.125 corrosion
allowance "
IJE
G
G
G
G
IJI
IJJ
IJL
IJT
OAE
PAA
TGL
TGM
TGN
TGQ
TGR
@@ASTM-A240-316,
Aitken, w/0.125 CA "
Strainer Specialties
!
!
!
H
H
H
H
H
H
0 1 2
1 2345678901234567890 SHORT DESCRIPTION LONG DESCRIPTION
FIRST LETTER: H - STRAINER SPECIALTIES
A
Basket strainer
Basket strainer
B
Temp basket strainer Temporary basket strainer
C
Cone strainer
Cone strainer
F
Flat strainer
Flat strainer
I
Inv cone strainer
Inverted cone strainer
P
Inclin perf pl
Inclined perforated strainer
strainer
H U
T-type thru strainer Tee-type assembly straight
thru pattern strainer
H V
T-type angle strainer Tee-type assembly angle
pattern strainer
H Y
Y-type strainer
Y-pattern strainer
H
H
AA
AB
ANSI-B16.5 CL150
ANSI-B16.5 CL300
ANSI-B16.5 CL150
ANSI-B16.5 CL300
459
460
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
AC
AD
AE
AF
AG
BA
BB
BH
CA
CB
CD
DA
DB
DC
DD
SA
SB
SC
SD
SE
SF
SG
SH
SI
TA
TB
TC
TD
TE
TF
TG
A
B
D
ANSI-B16.5 CL400
ANSI-B16.5 CL600
ANSI-B16.5 CL900
ANSI-B16.5 CL1500
ANSI-B16.5 CL2500
API-605 CL150
API-605 CL300
API-605 CL75
MSS-SP-44 CL150
MSS-SP-44 CL300
MSS-SP-44 CL600
ANSI-B16.1 CL25
ANSI-B16.1 CL125
ANSI-B16.1 CL250
ANSI-B16.1 CL800
CL150
CL300
CL400
CL600
CL900
CL1500
CL2500
CL250
CL175
AWWA-C207 Cl.E
Taylor Forge CL75
Taylor Forge CL125
Taylor Forge CL125LW
Taylor Forge CL175
Taylor Forge CL250
Taylor Forge CL350
FFFE
RFFE
RFFE, 125 Ra finish
ANSI-B16.5 CL400
ANSI-B16.5 CL600
ANSI-B16.5 CL900
ANSI-B16.5 CL1500
ANSI-B16.5 CL2500
API-605 CL150
API-605 CL300
API-605 CL75
MSS-SP-44 CL150
MSS-SP-44 CL300
MSS-SP-44 CL600
ANSI-B16.1 CL25
ANSI-B16.1 CL125
ANSI-B16.1 CL250
ANSI-B16.1 CL800
CL150
CL300
CL400
CL600
CL900
CL1500
CL2500
CL250
CL175
AWWA-C207 Cl.E
Taylor Forge CL75
Taylor Forge CL125
Taylor Forge CL125LW
Taylor Forge CL175
Taylor Forge CL250
Taylor Forge CL350
flat face flanged ends
raised face flanged ends
raised face flanged ends, 125
Ra finish
RFFE, 125-500 Ra
raised face flanged ends,
finish
125-500 Ra finish
RFFE, 63-250 Ra finish raised face flanged ends,
63-250 Ra finish
RFFE, 63-125 Ra finish raised face flanged ends,
63-125 Ra finish
RFFE, 125-250 Ra
raised face flanged ends,
finish
125-250 Ra finish
RJFE
ring joint flanged ends
M
N
R
BW x flange
flange x BW
RFFE, 3 Ra finish
H
H
H
H
S
T
W
Z
SWE
THD
BW
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
AA
AB
AC
AD
AF
AG
AH
AI
AJ
AK
AL
AM
AN
AO
AW
BA
BB
BC
BD
CA
CB
CC
CD
CE
CF
CG
CH
CI
CJ
CK
CL
CM
CN
CO
S-5S
S-10S
S-40S
S-80S
S-10
S-20
S-30
S-40
S-60
S-80
S-100
S-120
S-140
S-160
[???]|bore to match|
S-LW
S-STD
S-XS
S-XXS
0.125 "
0.188 "
0.25 "
0.312 "
0.375 "
0.438 "
0.5 "
0.562 "
0.625 "
0.688 "
0.75 "
0.812 "
0.875 "
0.938 "
1 "
buttweld x RF flange
RF flange x buttweld
raised face flanged ends, 3 Ra
finish
socketwelded ends
threaded
buttwelded
Sch 5S
Sch 10S
Sch 40S
Sch 80S
Sch 10
Sch 20
Sch 30
Sch 40
Sch 60
Sch 80
Sch 100
Sch 120
Sch 140
Sch 160
[???]
light-weight
standard-weight
X-strong
XX-strong
0.125 "
0.188 "
0.25 "
0.312 "
0.375 "
0.438 "
0.5 "
0.562 "
0.625 "
0.688 "
0.75 "
0.812 "
0.875 "
0.938 "
1 "
461
462
CP
CQ
CR
CS
DD
MA
MB
MC
MD
ME
MF
MG
MH
MI
MK
MM
MN
MO
MP
MQ
MR
MS
MT
MU
MV
PA
PB
PC
PD
PE
PF
PG
PH
PI
PJ
PK
PL
PM
PN
PO
PP
PQ
1.062 "
1.125 "
1.188 "
1.25 "
0.281 "
2.0 mm
2.5 mm
3.0 mm
3.5 mm
4.0 mm
4.5 mm
5.0 mm
6.0 mm
7.0 mm
10.0 mm
16.0 mm
20.0 mm
25.0 mm
30.0 mm
35.0 mm
40.0 mm
50.0 mm
60.0 mm
80.0 mm
100.0 mm
3.2 mm
4.8 mm
6.4 mm
7.9 mm
9.5 mm
11.1 mm
12.7 mm
14.3 mm
15.9 mm
17.5 mm
19.1 mm
20.6 mm
22.2 mm
23.8 mm
25.4 mm
27.0 mm
28.6 mm
1.062 "
1.125 "
1.188 "
1.25 "
0.281 "
2.0 mm
2.5 mm
3.0 mm
3.5 mm
4.0 mm
4.5 mm
5.0 mm
6.0 mm
7.0 mm
10.0 mm
16.0 mm
20.0 mm
25.0 mm
30.0 mm
35.0 mm
40.0 mm
50.0 mm
60.0 mm
80.0 mm
100.0 mm
3.2 mm (0.125) "
4.8 mm (0.188) "
6.4 mm (0.25) "
7.9 mm (0.312) "
9.5 mm (0.375) "
11.1 mm (0.438) "
12.7 mm (0.5) "
14.3 mm (0.562) "
15.9 mm (0.625) "
17.5 mm (0.688) "
19.1 mm (0.75) "
20.6 mm (0.812) "
22.2 mm (0.875) "
23.8 mm (0.938) "
25.4 mm (1) "
27.0 mm (1.062) "
28.6 mm (1.125) "
PR
PS
ZZ
30.2 mm
31.8 mm
AAD
AAE
H
H
AAF
AAJ
H
H
H
AAL
AAS
ACA
CS
CS, w/SS screen
ASTM-A516-60
ACB
ASTM-A516-60
ACE
ASTM-A516-60
ACG
ASTM-A516-60
ACH
ASTM-A516-60, w/SS
screen
ACK
ASTM-A516-60
ACM
ACN
ACP
ACQ
ACR
ADD
ASTM-A216-WCB,
screen
ASTM-A216-WCB,
screen
ASTM-A352-LCB,
screen
ASTM-A216-WCB,
screen
ASTM-A216-WCB,
screen
ASTM-A516-60
ADE
ASTM-A216-WCB, w/SS
screen
FFP
ASTM-A217-WC6, w/SS
screen
FFR
IAB
ASTM-A182-F22, w/SS
screen
316 SS/LO CS
IID
w/SS
w/SS
w/SS
w/SS
w/SS
ASTM-A351-CF8M, w/SS
screen
463
464
IIE
ASTM-A351-CF3M, w/SS
screen
ASTM-A351-CF8, w/SS
screen
ASTM-A351-CF8, w/SS
screen
ASTM-A351-CF8M
IIG
IIH
IIJ
H
H
H
IJP
IJR
IJS
IJT
ASTM-A240-304, w/SS
screen
IJU
ASTM-A240-316
IJV
ASTM-A240-316
IJW
ASTM-A240-304
IJX
ASTM-A240-304
IJY
ASTM-A240-304
IKA
ASTM-A240-304, w/SS
screen
IKB
ASTM-A240-304, w/SS
screen
IKC
ASTM-A240-321, w/SS
screen
IKD
IKE
ASTM-A240-321, w/SS
screen
ASTM-A351-CF8C
IKF
IKG
PAA
ASTM-A351-CN7M,
w/Alloy 20 screen
ZAA
ASTM-A395, w/SS
screen
ZAB
ASTM-A395, w/Monel
screen
ZAC
ASTM-A395, w/SS
screen
ZAD
ASTM-A395, w/SS
screen
ZAE
ASTM-A395, w/SS
screen
Instrument Specialties
! 0 1 2
! 1 2345678901234567890 SHORT DESCRIPTION LONG DESCRIPTION
! FIRST LETTER: I - INSTRUMENT SPECIALTIES (PDS WILL NOT USE)
I AA
Air selector
Air selector
I AD
adapter
adapter
I AE
I AJ
Syphon
Syphon
I BA
Banding kit
Banding kit
I BJ
Junction box
Junction box
I BO
I BP
Pipe clamp
Pipe clamp
I BR
I CB
Machine bolt
Machine bolt
I CN
Nut
Nut, w/spring
I CP
Push clips
Push clips
I CR
I CS
Split washer
Split washer
I CT
Threaded rod
Threaded rod
I CU
Machine screw
I DA
Dampener
Pulsation dampener
I EA
Splice
Splice
I FF
465
466
I FR
I GM
Gauge mounting
kit
I GP
Pressure gauge
Pressure gauge
I GR
Receiver gauge
Receiver gauge
I HC
Conduit clamp
I LA
Ladder tray
Ladder tray
I LB
Channel
Channel
I LC
Cover
Cover
I LD
Dropout
Dropout
I LE
Expansion
connector
Expansion connector
I LF
Flat connector
I LG
Reducer
Reducer connector offset
connector offset
I LH
I LL
Elbow 90 deg
Elbow 90 deg
I LR
Reducer
Reducer
I LT
Tee
Tee
I MA
Air manifold
Air manifold
I OR
Restriction
orifice
Restriction orifice
I PC
Cond pot
Condensate pot
I PD
Drip pot,
w/mounting tab
I PP
Seal patch
Seal patch
I PS
Seal pot
Seal pot
I RA
Air relay
Air relay
I RB
Booster relay
Booster relay
I RG
O ring gasket
O ring gasket
I RO
Rotometer
Rotometer
I RR
Relay
Relay
I SC
Column mount
support
I SF
Floor mount
support
Line mount
support
I SO
Off-platform
mount Support
I SP
Platform mount
support
I SS
Surface mount
support
I SW
Wall mount
support
I UA
Packing gland
Packing gland
I VA
Vert adapter
Vertical adapter
I WR
Raceway,
w/connector
I YA
Vent plug
Vent plug
I YB
Bugproof vent
Bugproof vent
I ZZ
single mount
single angle
mount
horizontal
double angle
mount
double mount
double mount
467
panel, w/angle
legs
std
standard
vertical
angled
angled
inside
inside
outside
outside
straight
straight
w/air header
w/air header
CA
clamped
clamped
CB
cabled
cables
CC
welded
welded
CD
bolted
bolted
CE
U-bolt
U-bolt
FA
flanged
flanged
SW
SW
socketwelded
TA
THD
threaded
TF
FTE
TG
TL
TM
MTE
TN
TS
male SW x FTE
TT
tube x tube
tube x tube
TX
MTE x FTE
WB
BW
buttwelded
ZZ
468
AAA
carbon steel
carbon steel
AAC
CS
AAD
CS
AAE
AISI-C1018
AAF
AISI-C1018
AAH
ASTM-A106-B
AAI
ASTM-A106-B
AAJ
CS
AAK
CS
AAL
CS
AAM
ASME-SA105,
SA106-B
AAN
ASTM-A106-B,
S-80
AAO
ASTM-A106-B
AAP
ASTM-A106-B
AAQ
CS
AAR
CS
AAS
CS
AAT
CS
AAU
CS
AAV
CS
AAW
CS
AAX
CS
AAY
CS
ABA
ASTM-A106-B
ABB
CS
ABC
CS
ABD
CS
ABE
CS
ABF
CS
469
ABG
CS
ABH
CS
ABI
CS
ABJ
CS
ABK
CS
ABL
CS
ABN
CS
ABO
CS
ABP
CS
ABQ
CS
ABR
CS
ABS
CS
ABT
CS
ABU
CS
ABV
CS
ABW
CS
ABX
CS
ABY
CS
ABZ
CS
ACA
CS
ACB
CS
ACC
CS
ACD
CS
ACE
CS
ACF
CS
ACG
CS
ACH
CS
ACI
CS
CS
ACJ
470
ACK
CS
ACL
CS
ACM
CS
ACN
CS
ACO
CS
ACP
CS
ACQ
CS
ACR
CS
ACS
CS
ACT
CS
ACU
CS
ACV
CS
ACW
CS
ACX
CS
ADA
CS
ADB
CS
ADC
CS
ADD
CS
ADE
CS
ADF
CS
ADG
CS
ADH
CS
ADI
CS
ADJ
CS
ADK
CS
ADL
CS
ADM
CS
ADN
CS
ADO
CS
ADP
CS
ADQ
CS
ADR
CS
ADS
CS
ADT
CS
ADV
CS
ADW
CS
ADX
CS
ADY
CS
ADZ
CS
AEB
CS
AEC
CS
471
472
AED
CS
AEE
CS
AEF
CS
AEG
CS
AZZ
matl unspec
no matl specified
CAA
CS
CAB
CS
CAC
CS
CAD
CS
CAE
CS
CAF
CS
CAG
CS
CAH
CS
CAI
CS
CAJ
CS
CAK
CS
CAL
CS
CAM
SS
CAN
CS
CAO
CS
CAP
CS
EAB
ASTM-A335-P11
FAA
316 SS FILTER
IAA
stainless steel
stainless steel
IAB
SS
IAC
316 SS
316 SS
IAF
316 SS
IAG
SS
IAH
316 SS
IAI
316 SS
IAJ
316 SS
IBB
SS
IBC
SS
IBD
SS
IIH
ASTM-A312-304
IIJ
ASTM-A479-316
IIK
ASTM-A479-316
IIL
304 SS
IIM
304 SS
IIN
ASTM-A312-304
IIO
ASTM-A312-304
IIP
ASTM-A312-304
IIQ
ASTM-A312-304
IIR
ASTM-A312-304
IIS
ASTM-A312-304
NAA
bronze
bronze
NAB
brass
NAC
brass
473
474
RAA
SAA
aluminum
aluminum
SBB
SBC
SBD
SCA
aluminum allloy
SCB
aluminum alloy
SCC
aluminum alloy
SCD
aluminum alloy
SCE
aluminum alloy
SCF
aluminum alloy
SCG
aluminum alloy
SCI
aluminum alloy
SCJ
aluminum alloy
TAA
Teflon
TAB
Viton
TAC
Thermoplastic
XXX
ZAB
cast iron
ZAC
ASTM-A126
ZZZ
no matl reqd
Pipe Supports
! 0 1 2
! 1 2345678901234567890 SHORT DESCRIPTION LONG DESCRIPTION
! FIRST LETTER: J - PIPE SUPPORTS (PDS WILL NOT USE)
J BA
NA base support
J BB
J BC
J BD
J BE
J BF
J BG
J BH
NA base support,
w/slide plate
J BR
Bracket
Bracket
J BS
J CA
J CB
J CC
Adj clevis
J CD
Pipe clamp
Pipe clamp
J CE
J CR
Riser clamp
Riser clamp
J DA
Dummy support
J EA
Fastener
Fastener
J EB
U-bolt, w/nuts
J EC
J ED
J FA
Pipe lug
Pipe lug
J FB
Beam
Beam
J FC
Trapeze
Trapeze
J FD
J FE
Stabilizer
Stabilizer
J FF
J FG
Pick-up support
Pick-up support
475
Welding lug
Welding lug
J FI
Frame support
Frame support
J FS
Flexible strut
Flexible strut
J GA
J HA
J IS
Instr support
Instrument support
J PA
Pipe anchor
Pipe anchor
J PB
J PC
Bolt-on shoe
J PD
J PE
J PG
Pipe guide
Pipe guide
J PH
J PI
J PJ
J PK
Pipe protection
saddle
J PP
J PS
Pipe shoe
Pipe shoe
J RA
Rod
Rod
J RB
Threaded rod
Threaded rod
J RC
J SB
Sway brace
Sway brace
J SH
Spring hanger
Spring hanger
J SM
Structural member
Structural member
J SP
Slide
Slide
J SS
Structural shape
Structural shape
J VA
Vessel bracket
J VG
Vessel guide
J VH
J VL
Vessel lugs
J VS
Snubber
Snubber
J ZZ
476
Heat or uninsulated
Heat insulated or
uninsulated
Cold or uninsulated
Cold insulated or
uninsulated
Cold insulated
Cold insulated
Heat insulated
Heat insulated
Uninsulated
Uninsulated
Plate
Plate
Flat bar
Flat bar
Angle
Angle
Channel
Channel
I-beam
I-beam
Wide flange
Wide flange
ST structural tee
ST structural tee
Tube
Tube
Attach to steel
Attachment to steel
2 "
2 "
3 "
3 "
4 "
4 "
5 "
5 "
6 "
6 "
477
478
7 "
7 "
8 "
8 "
50 mm
50 mm
75 mm
75 mm
100 mm
100 mm
125 mm
125 mm
150 mm
150 mm
175 mm
175 mm
200 mm
200 mm
AA
CS Spec 400-303-1
CS per Specification
400-303, Det 1
AAB
CS Spec 400-303-2
CS per Specification
400-303, Det 2
AAC
CS Spec 400-303-3
CS per Specification
400-303, Det 3
AAD
CS Spec 400-303-4
CS per Specification
400-303, Det 4
AAE
CS Spec 400-303-1A
CS per Specification
400-303, Det 1A
ACA
CS Spec 400-306-2
CS per Specification
400-306, Det 2
ACB
CS Spec 400-306-1
CS per Specification
400-306, Det 1
ACC
CS Spec 400-307-1A
CS per Specification
400-307, Det 1A
ACD
CS Spec 400-306-4
CS per Specification
400-306, Det 4
ACE
CS Spec 400-306-6
CS per Specification
400-306, Det 6
ACF
CS Spec 400-307-2A
CS per Specification
400-307, Det 2A
ACG
CS Spec 400-306-8
CS per Specification
400-306, Det 8
ACH
CS Spec 400-306-7
CS per Specification
400-306, Det 7
ACI
CS Spec 400-307-3A
CS per Specification
400-307, Det 3A
ACK
CS Spec 400-306-5
CS per Specification
400-306, Det 5
ACM
CS Spec 400-306-3
CS per Specification
400-306, Det 3
ACN
CS Spec 400-306-9
CS per Specification
400-306, Det 9
ADA
CS Spec 400-312-7
CS per Specification
400-312, Det 7
ADD
CS Spec 400-312-6
CS per Specification
400-312, Det 6
AEW
CS Spec 400-307-13
CS per Specification
400-307, Det 13
AFA
CS Spec 400-323-76,
78, 80
CS per Specification
400-323, Det 76, 78, 80
AFB
CS Spec 400-323-82
CS per Specification
400-323, Det 82
AFG
AFH
CS Spec 400-323-12
CS per Specification
400-323, Det 12
AHA
CS Spec 400-304-1
CS per Specification
400-304, Det 1
AHB
CS Spec 400-304-2
CS per Specification
400-304, Det 2
AHC
CS Spec 400-304-3
CS per Specification
400-304, Det 3
AHD
CS Spec 400-304-4
CS per Specification
400-304, Det 4
AHE
CS Spec 400-304-5
CS per Specification
400-304, Det 5
AHF
CS Spec 400-304-8
CS per Specification
400-304, Det 8
AHG
CS Spec 400-304-11
CS per Specification
400-304, Det 11
AHH
CS Spec 400-304-13
CS per Specification
400-304, Det 13
AHI
CS Spec 400-304-14
CS per Specification
400-304, Det 14
AHJ
CS Spec 400-304-15
CS per Specification
400-304, Det 15
AHK
CS Spec 400-304-17
CS per Specification
400-304, Det 17
479
480
AHL
CS Spec 400-304-21
CS per Specification
400-304, Det 21
AHM
CS Spec 400-304-22
CS per Specification
400-304, Det 22
AHN
CS Spec 400-304-23
CS per Specification
400-304, Det 23
AHO
CS Spec 400-304-25
CS per Specification
400-304, Det 25
AHP
CS Spec 400-304-27
CS per Specification
400-304, Det 27
AHQ
CS Spec 400-304-28
CS per Specification
400-304, Det 28
AHR
CS Spec 400-304-29
CS per Specification
400-304, Det 29
AHS
CS Spec 400-304-31
CS per Specification
400-304, Det 31
AHU
CS Spec 400-304-33
CS per Specification
400-304, Det 33
AHV
CS Spec 400-304-34
CS per Specification
400-304, Det 34
AHW
CS Spec 400-304-36
CS per Specification
400-304, Det 36
AHX
CS Spec 400-304-37
CS per Specification
400-304, Det 37
AHY
CS Spec 400-304-16
CS per Specification
400-304, Det 16
AHZ
CS Spec 400-304-18
CS per Specification
400-304, Det 18
BEL
CS Spec 400-307-22
CS per Specification
400-307, Det 22
BEM
CS Spec 400-307-23
CS per Specification
400-307, Det 23
BEN
CS Spec 400-307-24
CS per Specification
400-307, Det 24
BEO
CS Spec 400-307-25
CS per Specification
400-307, Det 25
BEP
CS Spec 400-307-26
CS per Specification
400-307, Det 26
BHA
CS Spec 400-304-20
CS per Specification
400-304, Det 20
BHB
CS Spec 400-304-24
CS per Specification
400-304, Det 24
CAA
ASTM-A516-65
ASTM-A516 Gr.65
CAC
ASTM-A307-A
CAD
ASTM-A36
ASTM-A36
CAE
ASTM-A105
ASTM-A105
CAG
ASTM-A36
CAH
CS
FAA
Cr Spec 400-303-1
FAB
Cr Spec 400-303-2
FAC
Cr Spec 400-303-3
FAD
Cr Spec 400-303-4
FAE
Cr Spec 400-303-1A
FCA
Cr Spec 400-306-2
FCB
Cr Spec 400-306-1
FCC
Cr Spec 400-307-1A
FCD
Cr Spec 400-306-4
FCE
Cr Spec 400-306-6
FCF
Cr Spec 400-307-2A
FCG
Cr Spec 400-306-8
FCH
Cr Spec 400-306-7
FCI
Cr Spec 400-307-3A
FCK
Cr Spec 400-306-5
481
482
FCM
Cr Spec 400-306-3
FCN
Cr Spec 400-306-9
FDA
Cr Spec 400-312-7
FDD
Cr Spec 400-312-6
FEW
Cr Spec 400-307-13
FHA
Cr Spec 400-304-4
FHB
Cr Spec 400-304-6
FHC
Cr Spec 400-304-9
FHD
Cr Spec 400-304-12
FHE
Cr Spec 400-304-15
FHF
Cr Spec 400-304-16
FHG
Cr Spec 400-304-17
FHH
Cr Spec 400-304-18
FHI
Cr Spec 400-304-23
FHJ
Cr Spec 400-304-24
FHK
Cr Spec 400-304-25
FHL
Cr Spec 400-304-26
FHM
Cr Spec 400-304-11
FHN
Cr Spec 400-304-13
GAA
ASTM-A387-11
GAB
ASTM-A387-22
GAC
ASTM-A193-B7
IAA
SS Spec 400-303-1
SS per Specification
400-303, Det 1
IAB
SS Spec 400-303-2
SS per Specification
400-303, Det 2
IAC
SS Spec 400-303-3
SS per Specification
400-303, Det 3
IAD
SS Spec 400-303-4
SS per Specification
400-303, Det 4
IAE
SS Spec 400-303-1A
SS per Specification
400-303, Det 1A
ICA
SS Spec 400-306-2
SS per Specification
400-306, Det 2
ICB
SS Spec 400-306-1
SS per Specification
400-306, Det 1
ICD
SS Spec 400-306-4
SS per Specification
400-306, Det 4
ICE
SS Spec 400-306-6
SS per Specification
400-306, Det 6
ICG
SS Spec 400-306-8
SS per Specification
400-306, Det 8
ICH
SS Spec 400-306-7
SS per Specification
400-306, Det 7
ICK
SS Spec 400-306-5
SS per Specification
400-306, Det 5
ICM
SS Spec 400-306-3
SS per Specification
400-306, Det 3
ICN
SS Spec 400-306-9
SS per Specification
400-306, Det 9
ICO
SS Spec 400-306-10
SS per Specification
400-306, Det 10
IDA
SS Spec 400-312-7
SS per Specification
400-312, Det 7
483
484
IDD
SS Spec 400-312-6
SS per Specification
400-312, Det 6
IEW
SS Spec 400-307-13
SS per Specification
400-307, Det 13
IFA
SS Spec 400-323-76,
78, 80
SS per Specification
400-323, Det 76, 78, 80
IFB
SS Spec 400-323-82
SS per Specification
400-323, Det 82
IFC
SS Spec 400-323-96,
98, 100
SS per Specification
400-323, Det 96, 98, 100
IFD
SS Spec 400-323-102
SS per Specification
400-323, Det 102
IFG
IFH
SS Spec 400-323-12
SS per Specification
400-323, Det 12
IHA
SS Spec 400-304-4
SS per Specification
400-304, Det 4
IHB
SS Spec 400-304-7
SS per Specification
400-304, Det 7
IHC
SS Spec 400-304-10
SS per Specification
400-304, Det 10
IHD
SS Spec 400-304-12
SS per Specification
400-304, Det 12
IHE
SS Spec 400-304-15
SS per Specification
400-304, Det 15
IHF
SS Spec 400-304-16
SS per Specification
400-304, Det 16
IHG
SS Spec 400-304-17
SS per Specification
400-304, Det 17
IHH
SS Spec 400-304-18
SS per Specification
400-304, Det 18
IHI
SS Spec 400-304-23
SS per Specification
400-304, Det 23
IHJ
SS Spec 400-304-24
SS per Specification
400-304, Det 24
IHK
SS Spec 400-304-25
SS per Specification
400-304, Det 25
IHL
SS Spec 400-304-26
SS per Specification
400-304, Det 26
IHM
SS Spec 400-304-11
SS per Specification
400-304, Det 11
IHN
SS Spec 400-304-13
SS per Specification
400-304, Det 13
IHO
SS Spec 400-304-14
SS per Specification
400-304, Det 14
IHP
SS Spec 400-304-21
SS per Specification
400-304, Det 21
IHQ
SS Spec 400-304-33
SS per Specification
400-304, Det 33
IHR
SS Spec 400-304-34
SS per Specification
400-304, Det 34
IHS
SS Spec 400-304-35
SS per Specification
400-304, Det 35
IHT
SS Spec 400-304-36
SS per Specification
400-304, Det 36
IHU
SS Spec 400-304-37
SS per Specification
400-304, Det 37
IHV
SS Spec 400-304-38
SS per Specification
400-304, Det 38
IHW
SS Spec 400-304-39
SS per Specification
400-304, Det 39
IHX
SS Spec 400-304-20
SS per Specification
400-304, Det 20
IHY
SS Spec 400-304-22
SS per Specification
400-304, Det 22
TAA
rigid polyurethane
foam
TAB
rigid polyurethane
foam
THS
graphite 400-304-30
TZA
high-density Ca
silicate
high-density calcium
silicate, w/vap barrier,
Power Piping HI-TEMP 9238
XAE
Spec 400-303-6
XAF
Spec 400-303-7
XAG
Spec 400-303-8
XAH
Spec 400-303-9
485
486
XAI
Spec 400-303-10
XAJ
Spec 400-303-11
XAK
Spec 400-303-12
XAL
Spec 400-303-13
XAM
Spec 400-303-14
XAN
Spec 400-303-12B
XDA
XEA
Spec 400-307-1
XEB
Spec 400-307-2
XEC
Spec 400-307-3
XED
Spec 400-307-4
XEE
Spec 400-307-5
XEF
Spec 400-307-6
XEG
Spec 400-307-7
XEH
Spec 400-307-8
XEI
Spec 400-307-9
XEJ
Spec 400-307-10
XEK
Spec 400-307-11
XEL
Spec 400-307-12
XEM
Spec 400-307-14
XEN
Spec 400-307-15
XEO
Spec 400-307-16
XEP
Spec 400-307-17
XEQ
Spec 400-307-18
XER
Spec 400-307-19
XES
Spec 400-307-4A
XET
Spec 400-307-7A
XEU
Spec 400-307-15A
XFA
Spec 400-323-1, 2, 3
XFB
XFC
XFG
Spec 400-323-4
XFI
XFJ
Spec 400-323-34
XFK
XFL
Spec 400-323-44
XFM
XFN
XGA
Spec 400-314-1
XGB
Spec 400-314-2
XGC
Spec 400-314-3
XGD
Spec 400-314-4
487
XHA
Spec 400-304-19
XHB
Spec 400-304-20
XHC
Spec 400-304-1
XHD
Spec 400-304-2
XHE
Spec 400-304-3
XHF
Spec 400-304-26
XHG
Spec 400-304-27
XHH
Spec 400-304-28
XIA
Spec 464-56-PSC
XXX
Labor Codes
L
! 0 1 2
! 1 2345678901234567890 SHORT DESCRIPTION LONG DESCRIPTION
! FIRST LETTER: L - LABOR CODES (PDS WILL NOT USE)
488
L BA
L BB
L
L
L
L
MA
PA
PB
PC
Miter elbow
Pipe cut
Pipe bevel
Pipe J-bevel
L PD
L PE
Pipe weld
Preheat weld
L PW
L RA
L RB
L SA
Unreinforced stub in
L SB
L SC
L SP
L TA
L TB
L TC
L TD
L TE
L
L
L
L
L
L
L
L
L
L
L
L
L
L
Z
BZ
CZ
DZ
GZ
HZ
IZ
JZ
KZ
NZ
OZ
PZ
QZ
TZ
3-diam
4-diam
5-diam
6-diam
1-cut
2-cut
3-cut
4-cut
5-cut
90 deg
60 deg
45 deg
30 deg
WOL/hdr weld
L
L
L
L
L
L
WZ
XZ
YZ
ZZ
AA
AB
BW
fillet weld
SW
S-5S
S-10S
relieving pipespool
Labor for unreinforced
stub in branch
Labor for weld
reinforced stub in
branch
Labor for pad
reinforced stub in
branch
Labor for weld reinf
stub in branch
requiring post weld
heat treatment
Labor for testing weld
by liquid penetrant
method
Labor for testing weld
by impact method
Labor for testing weld
by magnetic particle
method
Labor for testing weld
by radiography (1
shot)
Labor for testing weld
by radiography (2
shot)
3-diam
4-diam
5-diam
6-diam
1-cut
2-cut
3-cut
4-cut
5-cut
90 deg
60 deg
45 deg
30 deg
weldolet to header
weld
buttwelded
fillet weld
socketwelded
Sch 5S
Sch 10S
489
490
AC
AD
AF
AG
AH
AI
AJ
AK
AL
AM
AN
AO
AW
BA
BB
BC
BD
CA
CB
CC
CD
CE
CF
CG
CH
CI
CJ
CK
CL
CM
CN
CO
CP
CQ
CR
CS
CT
CU
CV
CX
DD
MA
S-40S
S-80S
S-10
S-20
S-30
S-40
S-60
S-80
S-100
S-120
S-140
S-160
[???]|bore to match|
S-LW
S-STD
S-XS
S-XXS
0.125 "
0.188 "
0.25 "
0.312 "
0.375 "
0.438 "
0.5 "
0.562 "
0.625 "
0.688 "
0.75 "
0.812 "
0.875 "
0.938 "
1 "
1.062 "
1.125 "
1.188 "
1.25 "
1.375 "
1.5 "
1.625 "
1.875 "
0.281 "
2.0 mm
Sch 40S
Sch 80S
Sch 10
Sch 20
Sch 30
Sch 40
Sch 60
Sch 80
Sch 100
Sch 120
Sch 140
Sch 160
[???]
light-weight
standard-weight
X-strong
XX-strong
0.125 "
0.188 "
0.25 "
0.312 "
0.375 "
0.438 "
0.5 "
0.562 "
0.625 "
0.688 "
0.75 "
0.812 "
0.875 "
0.938 "
1 "
1.062 "
1.125 "
1.188 "
1.25 "
1.375 "
1.5 "
1.625 "
1.875 "
0.281 "
2.0 mm
MB
MC
MD
ME
MF
MG
MH
MI
MJ
MK
ML
MM
MN
MO
MP
MQ
MR
MS
MT
MU
MV
NA
NB
NC
ND
NE
NF
NG
NJ
NK
NL
NM
NN
NO
NP
NQ
NR
NS
NT
NU
PA
PB
2.5 mm
3.0 mm
3.5 mm
4.0 mm
4.5 mm
5.0 mm
6.0 mm
7.0 mm
8.0 mm
10.0 mm
12.0 mm
16.0 mm
20.0 mm
25.0 mm
30.0 mm
35.0 mm
40.0 mm
50.0 mm
60.0 mm
80.0 mm
100.0 mm
2.2 mm
2.8 mm
3.2 mm
3.8 mm
4.2 mm
4.8 mm
5.5 mm
9.0 mm
11.0 mm
14.0 mm
18.0 mm
22.0 mm
28.0 mm
32.0 mm
38.0 mm
45.0 mm
55.0 mm
70.0 mm
90.0 mm
3.2 mm
4.8 mm
2.5 mm
3.0 mm
3.5 mm
4.0 mm
4.5 mm
5.0 mm
6.0 mm
7.0 mm
8.0 mm
10.0 mm
12.0 mm
16.0 mm
20.0 mm
25.0 mm
30.0 mm
35.0 mm
40.0 mm
50.0 mm
60.0 mm
80.0 mm
100.0 mm
2.2 mm
2.8 mm
3.2 mm
3.8 mm
4.2 mm
4.8 mm
5.5 mm
9.0 mm
11.0 mm
14.0 mm
18.0 mm
22.0 mm
28.0 mm
32.0 mm
38.0 mm
45.0 mm
55.0 mm
70.0 mm
90.0 mm
3.2 mm (0.125) "
4.8 mm (0.188) "
491
492
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
PC
PD
PE
PF
PG
PH
PI
PJ
PK
PL
PM
PN
PO
PP
PQ
PR
PS
ZZ
AA
AAB
AAC
AAD
AAE
AAF
AAG
AAH
AAI
6.4 mm
7.9 mm
9.5 mm
11.1 mm
12.7 mm
14.3 mm
15.9 mm
17.5 mm
19.1 mm
20.6 mm
22.2 mm
23.8 mm
25.4 mm
27.0 mm
28.6 mm
30.2 mm
31.8 mm
AAJ
ASTM-A53-B, galv
AAK
ASTM-A106-B, alum
AAN
ASTM-A106-B, galv
L
L
L
AAO
AAP
AAQ
ASTM-A135-A
ASTM-A135-B
ASTM-A139-A
AAR
ASTM-A139-B
AAS
ASTM-A672-B65
AAT
ASTM-A671-CC60
ASTM-A53-B
ASTM-A53-A
ASTM-A53-F
ASTM-A672-B65
ASTM-A106-B
ASTM-A106-A
ASTM-A106-C
ASTM-A672-C60
ASTM-A53-B, alum
ASTM-A53 Gr.B
ASTM-A53 Gr.A
ASTM-A53 Gr.F
ASTM-A672 Gr.B65
ASTM-A106 Gr.B
ASTM-A106 Gr.A
ASTM-A106 Gr.C
ASTM-A672 Gr.C60
ASTM-A53 Gr.B,
aluminized, per
ASTM-A676
ASTM-A53 Gr.B,
galvanized
ASTM-A106 Gr.B,
aluminized, per
ASTM-A676
ASTM-A106 Gr.B,
galvanized
ASTM-A135 Gr.A
ASTM-A135 Gr.B
ASTM-A139 Gr.A,
ASTM-A285 Gr.C
ASTM-A139 Gr.B,
ASTM-A285 Gr.C
ASTM-A672 Gr.B65, 200
BHN max
ASTM-A671 Gr.CC60
CL22
AAU
API-5L-A25 Cl.II
AAY
ASTM-A671-CC70 Cl.22
L
L
ABA
ABB
ASME-SA53-B
API-5L-B
L
L
L
L
L
ABC
ABE
ABH
ABL
ABS
API-5L-B
ASTM-A672-C60
ASME-SA106-B
ASTM-A333-6
API-5L-A
ABT
API-5L-B
ABU
API-5L-B
ACS
API-5L-A
ACT
API-5L-B
AZA
CS
EEA
ASTM-A335-P1
EEB
ASTM-A335-P15
EEC
ASTM-A335-P2
EZZ
ASTM-A691-CM70
L
L
FAA
FAB
ASTM-A691-5Cr
ASTM-A387-P9
L
L
L
FAC
FAD
FAE
ASTM-A691-1.25Cr
ASTM-A691/A387-P9
ASTM-A691-2.25 Cr
FFB
ASTM-A335-P12
FFC
ASTM-A335-P11
FFF
ASTM-A335-P22
FFG
ASTM-A335-P21
FFH
ASTM-A335-P5
FFI
ASTM-A335-P5B
FFJ
ASTM-A335-P5C
493
494
FFK
ASTM-A335-P7
FFL
ASTM-A335-P9
FGA
ASTM-A336-F11
FGB
ASTM-A336-F22
FGC
ASTM-A336-F21
FZA
Chrome
L
L
GAC
GFD
ASME-SA691-1.25Cr
ASME-SA335 P11
L
L
L
IIA
IIB
IIC
L
L
L
L
L
L
L
L
L
L
L
L
L
L
IID
IIE
IIF
IIG
IIH
III
IIJ
IIK
IIL
IIM
IIN
IIO
IIP
IIQ
ASTM-A312 TP304
ASTM-A312 TP304L
ASTM-A312 TP316L,
w/0.03% C max
ASTM-A312 TP309
ASTM-A312 TP310
ASTM-A312 TP316
ASTM-A312 TP316L
ASME-SA312 TP316L
ASTM-A312 TP317
ASTM-A312 TP321
ASTM-A312 TP321H
ASTM-A312 TP347
ASTM-A312 TP347H
ASTM-A312 TP348
ASTM-A312 TP348H
ASTM-A312 TP304H
ASTM-A358-304
IIR
ASTM-A358-309
IIS
ASTM-A358-310
IIT
ASTM-A358-316
IIU
ASTM-A358-321
IIV
ASTM-A358-347
IIW
ASTM-A358-348
IIX
ASTM-A358-304L
IIY
ASTM-A358-316L
ASTM-A335 Gr.P7,
7Cr-0.5Mo
ASTM-A335 Gr.P9,
9Cr-1Mo
ASTM-A336 Gr.F11,
1.25Cr-0.5Mo
ASTM-A336 Gr.F22,
2.25Cr-1Mo
ASTM-A336 Gr.F21,
3Cr-1Mo
Chrome (for reinforced
welds & buttwelds)
ASME-SA691 Gr.1.25Cr
ASME-SA335 P11,
1.25Cr-0.5Mo
ASTM-A312 Type 304
ASTM-A312 Type 304L
ASTM-A312 Type 316L,
w/0.03% C max
ASTM-A312 Type 309
ASTM-A312 Type 310
ASTM-A312 Type 316
ASTM-A312 TP316L
ASME-SA312 Type 316L
ASTM-A312 Type 317
ASTM-A312 Type 321
ASTM-A312 Type 321H
ASTM-A312 Type 347
ASTM-A312 Type 347H
ASTM-A312 Type 348
ASTM-A312 Type 348H
ASTM-A312 Type 304H
ASTM-A358 Gr.304, A240
Type 304
ASTM-A358 Gr.309, A240
Type 309
ASTM-A358 Gr.310, A240
Type 310
ASTM-A358 Gr.316, A240
Type 316
ASTM-A358 Gr.321, A240
Type 321
ASTM-A358 Gr.347, A240
Type 347
ASTM-A358 Gr.348, A240
Type 348
ASTM-A358 Gr.304L,
A240 Type 304L
ASTM-A358 Gr.316L,
A240 Type 316L
IIZ
IJQ
IJR
IJS
IJT
L
L
L
IJU
IJV
IJX
IJY
IKH
L
L
IKI
IKJ
IZA
L
L
MLF
MLI
L
L
MLS
OAA
OAB
PAA
SRF
SRG
SRH
SRJ
SRS
SRT
ASTM-A358-304H
ASTM-A409-TP304
ASTM-A409-TP304L
ASTM-A409-TP304, impact
at -325 degF
ASTM-A409-TP316, impact
at -325 degF
ASTM-A409-TP316
ASTM-A409-TP316L
ASTM-A358-304, impact
at -325 degF
ASTM-A358 Gr.304H
ASTM-A409 Type 304
ASTM-A409 Type 304L
ASTM-A409 Type 304,
impact at -325 degF
ASTM-A409 Type 316,
impact at -325 degF
ASTM-A409 Type 316
ASTM-A409 Type 316L
ASTM-A358 Gr.304, A240
TP 304, impact at -325
degF
ASTM-A358-316, impact
ASTM-A358 Gr.316, A240
at -325 degF
TP 316, impact at -325
degF
ASTM-A297-HF modified
ASTM-A297 Gr.HF,
modified
ASTM-A451-CPH 20
ASTM-A451 Gr.CPH-20
ASTM-A451-HF modified
ASTM-A451 Gr.HF
modified
SS
SS (for reinforced
welds & buttwelds)
ASTM-A333-3
ASTM-A333 Gr.3, 3.5Ni
ASTM-A333-4
ASTM-A333 Gr.4, Cr-Cu,
Ni
ASTM-A333-8
ASTM-A333 Gr.8, 9Ni
ASTM-B165 Monel
ASTM-B165, UNS N04400
Monel, annealed, 5 &
under OD "
ASTM-B514
ASTM-B514 Category 2,
UNS N08800
ASTM-B464 Alloy 20
ASTM-B464, UNS N08020,
Alloy 20
ASTM-B241 6063-T6
ASTM-B241 Alloy
6063-T6, as welded, T &
Y tests required
ASTM-B241 6061-T6
ASTM-B241 Alloy
6061-T6, as welded, T &
Y tests required
ASTM-B241 Alloy 6061-T6 ASTM-B261 Alloy
6061-T6, aluminum,
seamless
ASTM-B241 3003-H112
ASTM-B241 Alloy
3003-H112, use annealed
stresses
ASTM-B209 6061-T6
ASTM-B209 Alloy
6061-T6, use welded
stresses
ASTM-B209 6061-T6
ASTM-B209 Alloy
6061-T6, tol to A358,
use welded stresses
495
SZA
Inconel
WAA
WAB
WAC
API-5L-B, T & W
WAD
WAE
ASTM-A53-B, cement
lined
ASTM-A53-B, T & W
WAF
ASTM-A53-B, aluminized,
T & W
WXJ
ASTM-A106-B, T & W
WXK
WXL
ASTM-A106-B,
aluminized, T & W
WXM
ASTM-A53-B, cement
lined, T & W
WXN
ASTM-A53-B, galvanized,
T & W
WXV
ASTM-A106-B,
galvanized, T & W
Inconel (for
reinforced welds &
buttwelds)
API-5L Gr.B, cement
lined
API-5L Gr.B, cement
lined, treated &
wrapped
API-5L Gr.B, treated &
wrapped
ASTM-A53 Gr.B, cement
lined
ASTM-A53 Gr.B, treated
& wrapped
ASTM-A53 Gr.B,
aluminized, treated &
wrapped
ASTM-A106 Gr.B,
treated & wrapped
ASTM-A106 Gr.B, epoxy
coated
ASTM-A106 Gr.B,
aluminized, treated &
wrapped
ASTM-A53 Gr.B, cement
lined, treated &
wrapped
ASTM-A53 Gr.B,
galvanized, treated &
wrapped
ASTM-A106 Gr.B,
galvanized, treated &
wrapped
496
M AAAA
Speakman SE-505
'Speakman SE-505'
M ABBB
Spray Systems Co
M ABBC
Spray Systems Co
M ABBD
Spray Systems Co
M ABBE
Spray Systems Co
M ABBF
Spray Systems Co
M ABBG
Spray Systems Co
M ABBH
Spraco
M ABBI
Spraco
M ABBJ
Spraco
M HAAA
Halprin Supply Co
M TAAA
T D Williamson Co
M SN
'Spray nozzle'
M ZZ
M ZZZZ
M IAA
ASTM-A351-CF8
M IAB
ASTM-A276-316
M OAA
M XAI
M ZZZ
497
498
'Shield for
valve'
'Shield for
valve'
'Shield for
valve'
'Shield for
Duo-Chek II
N ZZ
N AAAA
N AAAB
N BAAA
'Babbitt'
N BAAB
'Rotohammer'
N BAAC
'Stockham'
N ZZZZ
N AAA
ASTM-A307-A, galv
N IIA
ASTM-A167-TP304 24 Ga
N VAA
rubber
'ASTM-A167 Gr.TP304 24 Ga
sheet'
'rubber'
N VAB
polypropylene
'polypropylene'
N VAC
N ZAA
N ZAB
ductile iron
'ductile iron'
Tube PE
Structural tube PE
O C
O D
499
O F
O G
O H
O J
O K
O L
O N
O O
O P
O Q
O R
O S
O T
O U
O V
O Z
O
O
O
O
O
O
O
O
O
O
500
A
B
C
D
E
F
G
L
M
Z
CL150
CL300
CL400
CL600
CL900
CL1500
CL2500
CL125
CL250
CL150
CL300
CL400
CL600
CL900
CL1500
CL2500
CL125
CL250
O
O
A
B
FFFE
RFFE
O
O
O
E
F
M
engineered hose
FTE
MTE
O
W
Z
smls
welded
seamless
welded
2 tube bundle
7 tube bundle
12 tube bundle
19 tube bundle
1 process, w/1 element
2 process, w/1 element
1 process 1 trace,
light
2 process 1 trace,
light
1 process 1 trace,
heavy
2 process 1 trace,
heavy
O
O
O
O
O
O
O
G
L
S
T
U
V
2 tube bundle
7 tube bundle
12 tube bundle
19 tube bundle
1 proc 1 elem
2 proc 1 elem
1 proc 1 trc lt
2 proc 1 trc lt
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
AA
AB
AC
BA
BB
BC
BD
BE
BF
BG
BH
BI
BJ
BK
BL
BM
BN
BO
BP
MA
MB
ZZ
AAD
AAO
Type K
Type L
Type M
0.02 "
0.028 "
0.03 "
0.032 "
0.035 "
0.04 "
0.049 "
0.062"
0.065 "
0.083 "
0.109 "
0.12 "
0.25 "
0.375 "
0.5 "
multi thk per reqn
1.0 mm
0.76 mm
ASTM-A179
CS, cadmium plated
Type K
Type L
Type M
0.02 "
0.028 "
0.03 "
0.032 "
0.035 "
0.04 "
0.049 "
'0.062"'
0.065 "
0.083 "
0.109 "
0.12 "
0.25 "
0.375 "
0.5 "
multi thk ??
1.0 mm
0.76 mm
ASTM-A179, annealed
CS, cadmium plated,
501
502
AAP
IIA
ASTM-A269-TP304
IIB
ASTM-A269-TP304L
IIE
ASTM-A269-TP316
IIF
ASTM-A269-TP316
IIG
ASTM-A269-TP316
IIH
316 SS/preinsul/PVC
III
316 SS
IIJ
ASTM-A269-TP321
IIK
ASTM-A269-TP316
IIL
ASTM-A269-TP347
IIM
ASTM-A269-TP316
IIN
ASTM-A269-TP316
IIO
ASTM-A269-TP316
IIP
316 SS
O
O
IIQ
IIR
316 SS
ASTM-A269-TP316
IIS
ASTM-A269-TP316
IJF
ASTM-A213-TP316
IJQ
solid 304 SS
NAA
ASTM-B68 Cu
NAB
copper/fibgl/PVC
NAC
copper/fibgl/PVC
Aeroquip No FD56-1037
CS, cadmium plated,
Dixon Boss X-34
ASTM-A269 Type 304,
annealed
ASTM-A269 Type 304L,
annealed
ASTM-A269 Type 316,
Dekoron 2201
ASTM-A269 Type 316,
annealed
ASTM-A269 Type 316,
Dekoron 2203
ASTM-A269-TP316 smls,
preinsulated tubing,
black PVC jkt, Dekoron
2200
316 stainless stl,
Snap-Tite H Series
nipple end
PHN-F/coupler end
PHC-F
ASTM-A269 Type 321,
annealed
ASTM-A269 Type 316,
Parker 422-208A 812-0
ASTM-A269 Type 347,
annealed
ASTM-A269 Type 316,
Dekoron 2256
ASTM-A269 Type 316,
Dekoron 2266
ASTM-A269 Type 316,
Parker 4412-208A 812-0
316 SS, Evertite Part
FLA
316 SS, Evertite
ASTM-A269 Type 316,
Dekoron 2202
ASTM-A269-TP316,
preinsulated tubing,
3T, 2 process, 1 tracer
ASTM-A213 Type 316,
annealed
solid 304 SS, Dixon
X-34
ASTM-B68, copper, UNS
No C12000
ASTM-B68 UNS C12200 IN
3/8 fiberglass black
PVC jkt Dekoron 2200
ASTM-B68 UNS C12200 IN
3/8 fiberglass black
NAD
NAE
NAF
NPA
NPB
WYH
WYI
WYJ
WYM
WYN
WYO
WYS
WYT
WYU
WYV
WYW
WYX
WYY
O
O
XXX
ZBL
503
ZBM
ZBN
ZBO
AM Series
malleable iron,
cadmium plated, Air King
#AM-7 & 12
malleable iron,
cadmium plated, Air King
#AM-8 & 13
malleable iron,
cadmium plated, Air King
#AM-18, 23, & 28
Pipe
! 0 1 2
P ! 1 2345678901234567890 SHORT DESCRIPTION LONG DESCRIPTION
! FIRST LETTER: P - PIPE
P AA
@@Pipe, BE
Pipe, beveled ends per
ANSI-B16.25
P AB
@@Pipe, T&C
Pipe, threaded &
coupled
P AC
@@Pipe, T&C, galv
Pipe, threaded &
coupled, galvanized
P AD
@@Pipe, PE
Pipe, plain ends
P AE
Pipe, PE, galv
Pipe, plain ends,
galvanized
P AF
@@Pipe bend, 6D-BR, BE Pipe bend, 6 nominal
pipe diameter radius,
beveled ends per
ANSI-B16.25
>> P AG
Pipe, BE, galv
Pipe, beveled ends,
galvanized
>> P AH
@@Pipe bend, 10D-BR, BE Pipe bend, 10 nominal
pipe diameter radius,
beveled ends per
Pipe bend, 10 nominal
pipe diameter radius,
beveled ends per
ANSI-B16.25
P CC
Pipe, w/split flg
Pipe, w/ends, w/split
flanges
P CD
Pipe, w/tapered ends
Pipe, w/tapered ends for
split flanges
P CE
Pipe, w/ends mach & cpld Pipe, w/ends machined
for rubber ring seals &
coupled
P DU
Duct
Duct
P EA
Pipe, cmt cpld
Pipe, cement coupled
nominal length
P GA
Pipe, groved ends for Pipe, ends grooved for
Vic coupling
Victaulic couplings
P NM
Nipple PE
Nipple, plain ends
504
Nipple, MTE
Nipple, MTE/PE
P NP
P NQ
Nipple, BE
Nipple, BE/MTE
P OA
P OB
P OC
P OD
P OE
P OF
P OH
@@Nipple, MTE/PE, 3
long "
@@Nipple, BE, 4 long "
P OI
P OJ
P OK
P OL
P OM
P OO
@@Nipple, MTE/PE, 4
long "
@@Nipple, BE, 5 long "
P OP
P OQ
P OR
P OS
P OT
P PA
@@Nipple, MTE/PE, 5
long "
@@Nipple, BE, 6 long "
P PB
P PC
P PD
P PE
P PF
@@Nipple, MTE/PE, 6
505
P PH
P PI
P PJ
P PK
P PL
P PM
P PO
P PP
P PQ
P PR
P PS
P PT
P QA
P QB
P QC
P QD
P QE
P QF
P QJ
P QK
P QL
P RP
P UA
P UB
P UC
506
long "
plain ends, 6 long "
@@Nipple, BE, 7 long " Nipple, beveled ends, 7
long "
@@Nipple, MTE, 7 long " Nipple, male threaded
ends, 7 long "
@@Nipple, PE, 7 long " Nipple, plain ends, 7
long "
Nipple, BE/MTE, 7 long " Nipple, beveled x male
threaded ends, 7 long "
Nipple, BE/PE, 7 long " Nipple, beveled x plain
ends, 7 long "
@@Nipple, MTE/PE, 7
Nipple, male threaded x
long "
plain ends, 7 long "
Nipple, BE, 8 long "
Nipple, beveled ends, 8
long "
@@Nipple, MTE, 8 long " Nipple, male threaded
ends, 8 long "
@@Nipple, PE, 8 long " Nipple, plain ends, 8
long "
Nipple, BE/MTE, 8 long " Nipple, beveled x male
threaded ends, 8 long "
Nipple, BE/PE, 8 long " Nipple, beveled x plain
ends, 8 long "
Nipple, MTE/PE, 8 long " Nipple, male threaded x
plain ends, 8 long "
Nipple, BE, 9 long "
Nipple, beveled ends, 9
long "
Nipple, MTE, 9 long " Nipple, male threaded
ends, 9 long "
@@Nipple, PE, 9 long " Nipple, plain ends, 9
long "
Nipple, BE/MTE, 9 long " Nipple, beveled x male
threaded ends, 9 long "
Nipple, BE/PE, 9 long " Nipple, beveled x plain
ends, 9 long "
Nipple, MTE/PE, 9 long " Nipple, male threaded x
plain ends, 9 long "
@@Nipple, PE, 10 long " Nipple, plain ends, 10
long "
@@Nipple, PE, 11 long " Nipple, plain ends, 11
long "
@@Nipple, PE, 12 long " Nipple, plain ends, 12
long "
@@Reinforcing pad
Reinforcing pad
Pipe, SPE/BLE, push-on Pipe, spigot x bell ends,
jt, 5 lay lngth
push-on joint, 5 laying
length
@@Pipe, SPE/BLE,
Pipe, spigot x bell ends,
push-on jt, 10 lay
push-on joint, 10 laying
lngth
length
Pipe, PE/BLE, push-on Pipe, plain x bell ends,
jt, 18 lay lngth
push-on joint, 18 laying
length
P
P
AA
AD
AE
AF
AG
AN
AO
AP
P
P
P
P
AX
BA
CT
GA
GF
JA
507
JD
JG
JN
JR
JS
JT
JU
JV
MA
PB
PC
WA
ZZ
P
P
P
P
P
P
P
P
P
P
P
508
AA
AB
AC
AD
AF
AG
AH
AI
AJ
AK
AL
Sch
Sch
Sch
Sch
Sch
Sch
Sch
Sch
Sch
Sch
Sch
5S
10S
40S
80S
10
20
30
40
60
80
100
AM
AN
AO
AW
AX
@@S-120
S-140
@@S-160
@@[401]
thk per reqn
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
BA
BB
BC
BD
BE
CA
CB
CC
CD
CE
CF
CG
CH
CI
CJ
CK
CL
CM
CN
CO
CP
CQ
CR
CS
CT
CU
CV
CW
CX
DD
EA
EB
EC
ED
EE
EF
EG
S-LW
@@S-STD
@@S-XS
@@S-XXS
S-XH
0.125 "
0.188 "
0.25 "
0.312 "
0.375 "
0.438 "
0.5 "
0.562 "
@@0.625 "
0.688 "
@@0.75 "
0.812 "
0.875 "
0.938 "
1 "
1.062 "
1.125 "
1.188 "
1.25 "
1.375 "
1.5 "
1.625 "
1.75 "
1.875 "
0.281 "
2 "
2.125 "
2.25 "
2.375 "
2.5 "
2.625 "
2.75 "
Sch 120
Sch 140
Sch 160
[401]
thk per specification
??
light-weight
standard-weight
X-strong
XX-strong
extra-heavy
0.125 "
0.188 "
0.25 "
0.312 "
0.375 "
0.438 "
0.5 "
0.562 "
0.625 "
0.688 "
0.75 "
0.812 "
0.875 "
0.938 "
1 "
1.062 "
1.125 "
1.188 "
1.25 "
1.375 "
1.5 "
1.625 "
1.75 "
1.875 "
0.281 "
2 "
2.125 "
2.25 "
2.375 "
2.5 "
2.625 "
2.75 "
509
510
EH
FE
MA
MB
MC
MD
ME
MF
MG
MH
MIP
MJ
MK
ML
MM
MN
MO
MP
MQ
MR
MS
MT
MU
MV
NA
NB
NC
ND
NE
NF
NG
NJ
NK
NL
NM
NN
NO
NP
NQ
NR
NS
NT
2.875 "
3.5 "
2.0 mm
2.5 mm
3.0 mm
3.5 mm
4.0 mm
4.5 mm
5.0 mm
6.0 mm
7.0 mm
8.0 mm
10.0 mm
12.0 mm
16.0 mm
20.0 mm
25.0 mm
30.0 mm
35.0 mm
40.0 mm
50.0 mm
60.0 mm
80.0 mm
100.0 mm
2.2 mm
2.8 mm
3.2 mm
3.8 mm
4.2 mm
4.8 mm
5.5 mm
9.0 mm
11.0 mm
14.0 mm
18.0 mm
22.0 mm
28.0 mm
32.0 mm
38.0 mm
45.0 mm
55.0 mm
70.0 mm
2.875 "
3.5 "
2.0 mm
2.5 mm
3.0 mm
3.5 mm
4.0 mm
4.5 mm
5.0 mm
6.0 mm
7.0 mm
8.0 mm
10.0 mm
12.0 mm
16.0 mm
20.0 mm
25.0 mm
30.0 mm
35.0 mm
40.0 mm
50.0 mm
60.0 mm
80.0 mm
100.0 mm
2.2 mm
2.8 mm
3.2 mm
3.8 mm
4.2 mm
4.8 mm
5.5 mm
9.0 mm
11.0 mm
14.0 mm
18.0 mm
22.0 mm
28.0 mm
32.0 mm
38.0 mm
45.0 mm
55.0 mm
70.0 mm
NU
PA
PB
PC
PD
PE
PF
PG
PH
PI
PJ
PK
PL
PM
PN
PO
PP
PQ
PR
PS
PT
PU
PV
PW
PX
PY
PZ
QA
QB
QC
QD
E
QF
QH
UH
UI
UJ
UK
VA
VB
VC
ZZ
90.0 mm
3.2 mm
4.8 mm
6.4 mm
7.9 mm
9.5 mm
11.1 mm
12.7 mm
14.3 mm
15.9 mm
17.5 mm
19.1 mm
20.6 mm
22.2 mm
23.8 mm
25.4 mm
27.0 mm
28.6 mm
30.2 mm
31.8 mm
37.0 mm
34.0 mm
39.0 mm
56.0 mm
41.0 mm
42.0 mm
29.0 mm
43.0 mm
44.0 mm
45.0 mm
46.0 mm
47.0 mm
26.0 mm
48.0 mm
CL50
CL51
CL52
@@thk per reqnt
@@Wall-A
@@Wall-B
@@Wall-C
@@
90.0 mm
3.2 mm (0.125) "
4.8 mm (0.188) "
6.4 mm (0.25) "
7.9 mm (0.312) "
9.5 mm (0.375) "
11.1 mm (0.438) "
12.7 mm (0.5) "
14.3 mm (0.562) "
15.9 mm (0.625) "
17.5 mm (0.688) "
19.1 mm (0.75) "
20.6 mm (0.812) "
22.2 mm (0.875) "
23.8 mm (0.938) "
25.4 mm (1) "
27.0 mm (1.062) "
28.6 mm (1.125) "
30.2 mm (1.188) "
31.8 mm (1.25) "
37.0 mm
34.0 mm
39.0 mm
56.0 mm
41.0 mm
42.0 mm
29.0 mm
43.0 mm
44.0 mm
45.0 mm
46.0 mm
47.0 mm
26.0 mm
48.00 mm
Class 50
Class 51
Class 52
thickness per reqnt
Wall-A
Wall-B
Wall-C
511
512
P
P
P
P
P
P
P
P
P
AA
AAB
AAC
AAD
AAE
AAF
AAG
AAH
AAI
@@ASTM-A53-B
ASTM-A53-A
ASTM-A53-F
ASTM-A672-B65
@@ASTM-A106-B
ASTM-A106-A
ASTM-A106-C
ASTM-A672-C60
ASTM-A53-B, alum
AAJ
@@ASTM-A53-B, galv
AAK
ASTM-A106-B, alum
AAN
ASTM-A106-B, galv
P
P
P
AAO
AAP
AAQ
ASTM-A135-A
ASTM-A135-B
ASTM-A139-A
AAR
ASTM-A139-B
AAS
ASTM-A672-B65
P
P
AAT
AAV
ASTM-A671-CC60
API-5L-X42
AAW
API-5L-X46
AAX
API-5L-X52
P
P
P
P
P
P
AAY
AAZ
ABA
ABB
ABC
ABD
P
P
P
P
P
P
P
ABE
ABH
ABL
ABS
ABT
ABU
ACS
ASTM-A671-CC70 Cl.22
ASTM-A53-B
@@ASME-SA53-B
API-5L-B
API-5L-B, w/PWHT
@@ASTM-A671-CC70
Cl.22, impact at -50
degF
ASTM-A672-C60 Cl.22
@@ASME-SA106-B
@@ASTM-A333-6
API-5L-A
@@API-5L-B
API-5L-B
API-5L-A
ASTM-A53 Gr.B
ASTM-A53 Gr.A
ASTM-A53 Gr.F
ASTM-A672 Gr.B65
ASTM-A106 Gr.B
ASTM-A106 Gr.A
ASTM-A106 Gr.C
ASTM-A672 Gr.C60
ASTM-A53 Gr.B,
aluminized per ASTM-A676
ASTM-A53 Gr.B,
galvanized
ASTM-A106 Gr.B,
aluminized per ASTM-A676
ASTM-A106 Gr.B,
galvanized
ASTM-A135 Gr.A
ASTM-A135 Gr.B
ASTM-A139 Gr.A,
ASTM-A285 Gr.C, plate
ASTM-A139 Gr.B,
ASTM-A285 Gr.C, plate
ASTM-A672 Gr.B65, 200
BHN max
ASTM-A671 Gr.CC60 CL22
API-5L Gr.X42, cold
expanded
API-5L Gr.X46, cold
expanded
API-5L Gr.X52, cold
expanded
ASTM-A671 Gr.CC70 Cl.22
ASTM-A53 Type E Gr.B
ASME-SA53 Gr.B
API-5L Gr.B, 200 BHN max
API-5L Gr.B, w/PWHT
ASTM-A671 Gr.CC70 Cl.22,
impact at -50 degF
ASTM-A672 Gr.C60 Cl.22
ASME-SA106 Gr.B
ASTM-A333 Gr.6
API-5L Gr.A
API-5L Gr.B
API-5L Gr.B, 22 HRC max
API-5L Gr.A, cold
expanded
ACT
API-5L-B
P
P
AXZ
EEA
CS
ASTM-A335-P1
EEB
ASTM-A335-P15
P
P
EXZ
EZZ
carbon moly
ASTM-A691-CM70
P
P
P
P
FAA
FAC
FAD
FAE
ASTM-A691-5Cr
ASTM-A691-1.25Cr
ASTM-A691/A387-P9
ASTM-A691-2.25Cr
FFB
ASTM-A335-P12
P
P
FFC
FFF
@@ASTM-A335-P11
ASTM-A335-P22
FFG
ASTM-A335-P21
P
P
FFH
FFI
@@ASTM-A335-P5
ASTM-A335-P5B
FFJ
ASTM-A335-P5C
FFK
ASTM-A335-P7
P
P
FFL
FGA
@@ASTM-A335-P9
ASTM-A336-F11
FGB
ASTM-A336-F22
FGC
ASTM-A336-F21
FGE
ASTM-A336-F22
P
P
P
P
FXZ
GAC
GFD
GFF
chrome
ASME-SA691-1.25Cr
@@ASME-SA335-P11
ASME-SA335-P22
P
P
P
IIA
IIB
IIC
P
P
P
IID
IIE
IIF
@@ASTM-A312-TP304
@@ASTM-A312-TP304L
ASTM-A312-TP316L,
w/0.03% C max
ASTM-A312-TP309
ASTM-A312-TP310
@@ASTM-A312-TP316
513
514
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
IIG
IIH
III
IIJ
IIK
IIL
IIM
IIN
IIO
IIP
IIQ
IIR
IIS
IIT
IIU
IIV
IIW
IIX
IIY
IIZ
IJQ
IJR
IJS
ASTM-A312-TP316L
ASME-SA312-TP316L
ASTM-A312-TP317
@@ASTM-A312-TP321
ASTM-A312-TP321H
ASTM-A312-TP347
ASTM-A312-TP347H
ASTM-A312-TP348
ASTM-A312-TP348H
ASTM-A312-TP304H
@@ASTM-A358-304
ASTM-A358-309
ASTM-A358-310
ASTM-A358-316
ASTM-A358-321
ASTM-A358-347
ASTM-A358-348
ASTM-A358-304L
ASTM-A358-316L
ASTM-A358-304H
ASTM-A409-TP304
ASTM-A409-TP304L
ASTM-A409-TP304,
impact at -325 degF
ASTM-A409-TP316,
impact at -325 degF
IJT
P
P
P
IJU
IJV
IJX
ASTM-A409-TP316
ASTM-A409-TP316L
@@ASTM-A358-304,
impact at -325 degF
ASTM-A358-316, impact
at -325 degF
IJY
IKH
ASTM-A297-HF modified
P
P
IKI
IKJ
ASTM-A451-CPH 20
ASTM-A451-HF modified
P
P
P
IXZ
MLF
MLI
SS
ASTM-A333-3
ASTM-A333-4
P
P
MLS
OAA
ASTM-A333-8
ASTM-B407 Incoloy
OAB
PAA
PAP
SRG
SRH
SRJ
SRS
SRT
SRU
SRV
TAA
TAB
UAA
VAA
VBA
VBB
VCA
VDA
ASTM-B514
ASTM-B514 category 2,
UNS N08800
ASTM-B464 Alloy 20
ASTM-B464, UNS N08020,
Alloy 20
ASTM-B241-6063-T6
ASTM-B241 Alloy 6063-T6,
as welded, T & Y tests
required
ASTM-B241-6061-T6
ASTM-B241 Alloy 6061-T6,
as welded, T & Y tests
required
ASTM-B241-6061-T6
ASTM-B241 Alloy 6061-T6,
aluminum, seamless
ASTM-B241-3003-H112
ASTM-B241 Alloy
3003-H112, use annealed
stresses
ASTM-B209-6061-T6
ASTM-B209 Alloy 6061-T6,
use welded stresses
ASTM-B209-6061-T6
ASTM-B209 Alloy 6061-T6,
tol to A358, use welded
stresses
@@ASTM-B168-600
ASTM-B168 Gr.600 UNS
N06600, annealed &
pickled
@@ASTM-B167-600
ASTM-B167 Gr.600 UNS
N06600, cold drawn,
annealed & pickled
ASTM-F441 CPVC
ASTM-F441 Cl.23447-B
CPVC
@@ASTM-D1785 PVC
ASTM-D1785 Cl.12454-B
PVC
ASTM-D2996, epoxy lined ASTM-D2996-RTRP-11FE,
reinforced epoxy lined
@@ASTM-A74 w/rubber
ASTM-A74 w/preformed
gskt
rubber gasket per
ASTM-C564
@@AWWA-C151, dbl thk
ANSI/AWWA-C151/A21.51,
cement lined w/gskt
double thickness cement
lined, asphalt coated,
w/preformed rubber gasket
per
ANSI/AWWA-C111/A21.11
@AWWA-C151 dbl cmnt
ANSI/AWWA-C151/A21.51,
lind w/gskt,glnd & blt double thickness cement
lined, asphalt coated,
mechanical joint
w/preformed rubber gasket
per
ANSI/AWWA-C111/A21.11,
gland & bolts
@@ASTM-C700
ASTM-C700 w/bonded
w/polyurethane compr
polyurethane compression
coupl
coupling per ASTM-C425
ASTM-C76 Cl-I w/rubber ASTM-C76 Cl-I w/rubber
gskt
gasket per ASTM-C443
515
VDB
VDC
VDD
P
P
VDE
WAA
WAB
WAC
WAD
WAE
WAF
WXJ
WXK
WXL
WXM
WXN
WXV
WXW
WXX
WXY
Socket Fittings
! 0 1
2
! 1 2345678901234567890
SHORT DESCRIPTION
DESCRIPTION
! FIRST LETTER: Q - SOCKET FITTINGS
516
Q AA
@@Coupling, SE
Q AB
SE half coupling
Q AC
SE tang coupling
LONG
SE 45 deg coupling
Q AE
Q BA
@@Insert bushing, SE
Q BB
Q CA
@@Cap, SE
Q HA
@@Union, SE
Q HB
SE union Br/ftg
Q HC
SE orifice union
Q HD
Q HE
SE union, w/gasket
Q LA
Q LB
Q LC
Q PA
SE plug
Q PB
Q SA
SE reducer
Q TA
@@Tee, SE
SE red tee
Q TL
SE 45 deg lateral
Q TM
Q XA
SE cross
Q Z
@@
Q R
cemented
'cemented'
Q U
insul
'insulating'
Q Z
@@
Q AI
S-40
'Sch 40'
Q AK
@@S-80
'Sch 80'
Q TAA
ASTM-F439 CPVC
Q TAB
@@ASTM-D2467 PVC
Q TB
Q ZZ
517
Q ZZZ
Tubing Fittings
!
0
1
2
!
1 2345678901234567890
SHORT DESCRIPTION
DESCRIPTION
!
FIRST LETTER: R - TUBING FITTINGS
518
R BA
Tube clamp
'Tubing clamp'
R CA
Cap
'Tubing cap'
R DB
Male adapter
R DC
Female adapter
R FA
Front ferrule
R FB
Back ferrule
R FC
Ferrule
R FD
Sleeve
R FE
R HA
Union
'Tubing union'
R HB
Reducing union
R HC
Bulk union
R IA
R LA
Union elbow
R LC
Male 45 ell
R LF
Female elbow
R LG
Male elbow
R LH
Elbow
'Tubing elbow,
joint'
R LI
45 ell
R NA
Nut
'Tubing nut'
R PA
Plug
'Tubing plug'
LONG
solder
R QB
R QC
R QF
R QG
R QH
R QL
R QM
R QN
R QP
R QR
R RA
Reducer
'Tubing reducer'
R RB
R RC
Bulkhead reducer
R RD
Reducing coupling
R SA
Tube sleeve
'Tubing sleeve'
R TA
Union tee
R TC
R TD
R TE
R TF
R TG
Tee
R TH
Reducing tee
519
Female connector
R VC
Male connector
R VD
R VE
Bulkhead female
connector
R VF
R VG
Reducing coupling
R XA
Union cross
R C
R D
R F
37 flare
R G
45 flare
R K
Crimp ring
R P
R Q
R R
Socketwelded
'socketwelded'
R S
silver braze
'silver brazing'
R T
solder
'solder'
R U
THD/coned
R V
THD ferrule
'threaded ferrule'
R Z
R Z
520
''
R A
all tube
'all tube'
R B
R C
R F
R G
R H
R I
R L
quick conn/FTE
quick conn/MTE
R N
quick conn/tube
R O
R P
tube x FTE
R Q
tube x MTE
R R
R S
R T
R U
R Z
''
R AAA
steel
'steel'
R AAB
R AAP
R AAQ
R AAR
steel
'steel, Ermeto'
R AAS
steel
'steel, Swagelok'
R AAT
steel
R AAU
R ABA
stl/flare
R IIA
ASTM-A182-F304
'ASTM-A182 Gr.F304'
R IIB
STM-A182-F304
'ASTM-A182 Gr.F304,
Swagelok'
R IIC
ASTM-A182-F304L
'ASTM-A182 Gr.F304L'
R IIF
ASTM-A182-F316
'ASTM-A182 Gr.F316'
R IIG
316 SS
R IIH
17-4 PH ferrule
521
522
R III
R IIJ
ASTM-A182-F321
'ASTM-A182 Gr.F321'
R IIK
ASTM-A182-F321
'ASTM-A182 Gr.F321,
Swagelok'
R IIN
316 SS
'316 SS'
R IIO
ASTM-A182-F316
R IIP
ASTM-A182-F304
R IIQ
ASTM-A182-F316
R IIR
ASTM-A182-F316
'ASTM-A182 Gr.F316,
Ermeto'
R IIS
ASTM-A182-F316
'ASTM-A182 Gr.F316,
Swagelok'
R IIT
ASTM-A182-F316
'ASTM-A182 Gr.F316,
Imperial Hi-Seal'
R IIU
ASTM-A182-F316
R IIV
ASTM-A182-F316
R IIW
ASTM-A182-F316
R IIX
ASTM-A182-F316
R IIY
ASTM-A182-F316
'ASTM-A182 Gr.F316,
Swagelok QC Series or
approved equal'
R IIZ
ASTM-A182-F316
'ASTM-A182 Gr.F316,
Swagelok QF Series or
approved equal'
R IJL
ASTM-A182-F347
R NOA
bronze
'bronze, Walseal'
R NOB
bronze
'bronze'
R NOF
brass
R NOJ
R NPA
copper
'wrought copper'
ASTM-B36
R NPD
R NPE
brass
'brass'
R NPF
R NPG
R NPJ
R NPK
brass
'brass compression,
Imperial'
R NPM
brass
R NPQ
brass
'brass, Gyrolok'
R NPR
brass
'brass, Ermeto'
R NPS
brass
'brass, Swagelok'
R NPT
R NPU
brass
R NPV
brass
R NPW
brass
R NPX
brass
R NPY
brass flare
'brass flare'
R ONF
Hast B
'Hastelloy B, Swagelok'
R ONH
Monel
'Monel'
R ONJ
Monel
'Monel, Swagelok'
R ONO
nickel
'nickel'
R SRH
aluminum
'aluminum'
R SRS
aluminum
'aluminum, Swagelok, no
equal'
R SRU
aluminum
'aluminum, Imperial
Hi-Seal'
R TUA
black plastic
R TUF
polyethylene
'polyethylene'
R TUL
polystyrene
'polystyrene'
523
Socketwelded Fittings
! 0 1 2
! 1 2345678901234567890 SHORT DESCRIPTION LONG DESCRIPTION
! FIRST LETTER: S - SOCKETWELDED FITTINGS
524
S AA
@@Coupling, SWE
Coupling, socketwelded
ends
S AB
Socketwelded half
coupling
S AC
Socketwelded tangential
coupling
S AD
Socketwelded 45 deg
coupling
S AE
S BA
SWE insert
Socketwelded insert
bushing
S BB
Socketwelded reducing
bushing male x FPT
S CA
@@Cap, SWE
S HA
@@Union, SWE
Union, socketwelded
ends, fitting material
seats
S HB
S HC
Socketwelded union
restriction orifice
S HD
Socketwelded union
O-ring seat
S HE
Socketwelded union,
w/gasket
S LA
90 deg elbow,
socketwelded ends
S LB
Socketwelded 90 deg
reducing elbow
S LC
45 deg elbow,
SWE plug
Socketwelded plug
S PB
Socketwelded plug 4
long "
S SA
SWE reducer
Socketwelded reducer
S TA
@@Tee, SWE
S TB
Reducing tee,
socketwelded ends
S TL
45 deg lateral,
socketwelded ends
S TM
S XA
SWE cross
Socketwelded cross
CL150
CL150
CL300
CL300
CL2500
CL2500
@@CL3000
CL3000
@@CL6000
CL6000
@@CL9000
CL9000
cemented
cemented
insul
insulating
round bar
round barstock
hex bar
hex barstock
API
API
@@
AI
S-40
Sch 40
AK
S-80
Sch 80
AO
S-160
Sch 160
BB
S-STD
standard-weight
BC
S-XS
X-strong
BD
S-XXS
XX-strong
ZZ
@@
525
526
AAA
@@ASTM-A105
ASTM-A105
AAD
ASME-SA234-WPB
ASME-SA234 Gr.WPB
AAN
ASTM-A105, galv
ASTM-A105, galvanized
AAS
ASTM-A105
AAT
ASME-SA105
ABB
@@ASTM-A350-LF2
ASTM-A350 Gr.LF2
ABE
@@ASME-SA105
ASME-SA105
FFB
ASTM-A182-F12
ASTM-A182 Gr.F12,
1Cr-0.5Mo
FFC
@@ASTM-A182-F11
ASTM-A182 Gr.F11
FFF
ASTM-A182-F22
ASTM-A182 Gr.F22,
2.25Cr-1Mo
FFG
ASTM-A182-F21
ASTM-A182 Gr.F21,
3Cr-1Mo to ASTM-A234
FFH
@@ASTM-A182-F5
ASTM-A182 Gr.F5
FFI
ASTM-A182-F5A
ASTM-A182 Gr.F5A,
5.5Cr-0.5Mo
FFK
ASTM-A182-F7
ASTM-A182 Gr.F7,
7Cr-0.5Mo
FFL
@@ASTM-A182-F9
ASTM-A182 Gr.F9
GFD
@@ASME-SA182-F11
ASME-SA182 Gr.F11
GFF
ASSME-SA182-F22
ASME-SA182 Gr.F22,
2.25Cr-1Mo
IIA
@@ASTM-A182-F304
ASTM-A182 Gr.F304
IIB
@@ASTM-A182-F304L
ASTM-A182 Gr.F304L
IIE
ASTM-A182-F310
ASTM-A182 Gr.F310
IIF
@@ASTM-A182-F316
ASTM-A182 Gr.F316
IIG
ASTM-A182-F316L
ASTM-A182 Gr.F316L
IIH
ASME-SA182-F316L
ASME-SA182 Gr.F316L
IIJ
@@ASTM-A182-F321
ASTM-A182 Gr.F321
IIL
ASTM-A182-F347
ASTM-A182 Gr.F347
IIN
ASTM-A182-F348
ASTM-A182 Gr.F348
IIP
ASTM-A182-F304H
ASTM-A182 Gr.F304H
IIY
ASTM-A182-F347H
ASTM-A182 Gr.F347H
IJF
ASTM-182-F316L, special
ASTM-182 Gr.F316L,
w/0.035% C max, 12% Ni
min, 2.2% Mo min
OAC
ASTM-B564
OAD
@@ASTM-B366-WPNC1
SRF
aluminum
ASTM-B361, Alloy
WP6063-T6, aluminum
SRG
aluminum
ASTM-B361, Alloy
WP6061-T6, aluminum
TAA
ASTM-F439 CPVC
ASTM-F439 Cl.23447-B,
CPVC
TAB
ASTM-D2467 PVC
ASTM-D2467 Cl.12454-B
PVC
Threaded Fittings
! 0 1 2
! 1 2345678901234567890 SHORT DESCRIPTION LONG DESCRIPTION
! FIRST LETTER: T - THREADED FITTINGS
T AA
@@Coupling, FTE
Coupling, female
threaded ends
T AC
Threaded tangential
coupling
T AD
Threaded combination
coupling
T AE
T AF
Reducing threaded
coupling
T BA
T BB
THD fl bushing
T BC
Threaded reducing
bushing
T CA
@@Cap, FTE
T DA
THD adapter
Threaded adapter
T DB
Threaded reducing
adapter
T HA
@@Union, FTE
T HB
527
528
T HC
Threaded union
restriction orifice
T HD
T LA
T LB
T LC
T LD
T PA
@@Plug, MTE
T PB
T SA
@@Reducer, FTE
T TA
@@Tee, FTE
T TB
T TC
T TL
@@Lateral, FTE
T TM
@@Reducing lateral,
FTE
T UA
T XA
THD cross
Threaded cross
CL150
CL150
@@CL300
CL300
CL2500
CL2500
CL125
CL125
CL250
CL250
CL2000
CL2000
@@CL3000
CL3000
@@CL6000
CL6000
CL9000
CL9000
@@
MTE/red FTE
FTE/red MTE
M SW/FTE
male socketwelded x
female threaded
F SW/FTE
female socketwelded x
female thread
MTE/FTE
insul
insulating
@@round head
round head
hex head
hex head
API
API
sq head
square head
@@
AI
S-40
Sch 40
AK
S-80
Sch 80
AO
S-160
Sch 160
AW
[???]|bore to match|
[???]
BA
S-LW
light-weight
BB
S-STD
standard-weight
BC
S-XS
X-strong
BD
S-XXS
XX-strong
ZZ
@@
AAA
@@ASTM-A105
ASTM-A105
AAE
ASTM-A106-B
ASTM-A106 Gr.B
AAF
ASTM-A106-A
ASTM-A106 Gr.A
AAM
ASTM-A105, alum
ASTM-A105, aluminized to
ASTM-A676
AAN
@@ASTM-A105, galv
ASTM-A105, galvanized
AAT
API-5L-B
API-5L Gr.B
AAU
ASTM-A108-G10180
AAX
AISI-1018
AISI-1018 barstock
529
530
AAY
AISI-1018
AISI-1025 barstock
AAZ
AISI-4140
AISI-4140 barstock
ABB
@@ASTM-A350-LF2
ASTM-A350 Gr.LF2
ABE
@@ASME-SA105
ASME-SA105
EEA
ASTM-A182-F1
EEC
ASTM-A182-F1 mod
FFB
ASTM-A182-F12
ASTM-A182 Gr.F12,
1Cr-0.5Mo
FFC
@@ASTM-A182-F11
ASTM-A182 Gr.F11
FFF
ASTM-A182-F22
ASTM-A182 Gr.F22,
2.25Cr-1Mo
FFG
ASTM-A182-F21
ASTM-A182 Gr.F21,
3Cr-1Mo
FFH
@@ASTM-A182-F5
ASTM-A182 Gr.F5
FFI
ASTM-A182-F5A
ASTM-A182 Gr.F5A,
5Cr-0.5Mo
FFK
ASTM-A182-F7
ASTM-A182 Gr.F7,
7Cr-0.5Mo
FFL
@@ASTM-A182-F9
ASTM-A182 Gr.F9
GFD
@@ASME-SA182-F11
ASME-SA182 Gr.F11
GFF
ASME-SA182-F22
ASME-SA182 Gr.F22,
2.25Cr-1Mo
HIO
ASTM-A276-TP410
IIA
@@ASTM-A182-F304
ASTM-A182 Gr.F304
IIB
@@ASTM-A182-F304L
ASTM-A182 Gr.F304L
IIE
ASTM-A182-F310
ASTM-A182 Gr.F310
IIF
@@ASTM-A182-F316
ASTM-A182 Gr.F316
IIG
ASTM-A182-F316L
ASTM-A182 Gr.F316L
IIH
ASTM-A182-F316L,
w/0.030% C max
ASTM-A182 Gr.F316L,
w/0.030% C max
IIJ
@@ASTM-A182-F321
ASTM-A182 Gr.F321
IIL
ASTM-A182-F347
ASTM-A182 Gr.F347
IIN
ASTM-A182-F348
ASTM-A182 Gr.F348
IIP
ASTM-A182-F304H
ASTM-A182 Gr.F304H
IIQ
ASTM-A276-TP304
IIR
ASTM-A276-TP304L
IIU
ASTM-A276-TP316L
IIV
ASTM-A276-TP316
IIW
ASTM-A276-TP347
IIY
ASTM-A182-F347H
ASTM-A182 Gr.F347H
IJF
ASTM-A182-F316L,
special
ASTM-A182 Gr.F316L,
w/0.035% C max, 12% Ni
min, 2.2% Mo min
IJK
ASTM-A182-F316,
modified
ASTM-A182 Gr.F316
modified, w/0.03% C max,
11.5% Ni min
IJL
ASTM-A182-F316L
ASTM-A182 Gr.F316L,
w/11.5% Ni min
MLF
ASTM-A350-LF3
NAB
ASTM-B16
NAC
Cu/steel
copper/ASTM-A105
NPE
brass
brass
OAA
ASTM-B564
OAD
@@ASTM-B366-WPNC1
OND
ASTM-B366
ASTM-B366 Gr.WPNC,
Monel
PAA
ASTM-B462
SRG
aluminum
ASTM-B247, Alloy
6061-T6, aluminum
SRJ
aluminum
ASTM-B247, Alloy
3003-HII2, aluminum
SRS
aluminum
ASTM-B221, Alloy
6061-T6
SRU
aluminum
TAA
ASTM-F439 CPVC
ASTM-F439 Cl.23447-B
CPVC
TAB
ASTM-D2467 PVC
ASTM-D2467 Cl.12454-B
PVC
WAA
ASTM-A105 T&W
531
WAB
ASTM-A105, aluminized,
treated & wrapped
ZDK
ASTM-A338, malleable
iron, galvanized
ZDL
ZDM
ASTM-A395 DI
ZDP
Underground Fittings
!
!
!
532
0
1
2
1
2345678901234567890
SHORT DESCRIPTION
LONG DESCRIPTION
FIRST LETTER: U - UNDERGROUND FITTINGS
U AA
@@1/4 bend
'Quarter bend'
U AD
@@1/8 bend
'Eight bend'
U AI
1/16 bend
'Sixthteen bend'
U CA
@@Connecting piece
'Connecting piece'
U DC
@@Double hub
'Double hub'
U DD
U FA
U LA
@@Wye
'Wye'
U LB
@@Reducing wye
'Reducing wye'
U LC
True Wye
'True wye'
U LD
U LG
U LH
U MA
U PA
Threaded plug
'Threaded plug'
U PB
@@Plug
'Plug'
U RA
@@Concentric reducer
'Concentric reducer'
U RB
Eccentric reducer
'Eccentric reducer'
@@Concentric increaser
'Concentric increaser'
U TA
@@Tee
'Tee'
U TB
@@Reducing tee
'Reducing tee'
' '
U A
CL25
'CL25'
U B
CL125
'CL125'
U C
CL150
'CL150'
U D
CL175
'CL175'
U E
@@CL250
'CL250'
U F
CL300
'CL300'
U G
@@CL350
'CL350'
U Z
@@
''
U C
@@FFFE/PE
U D
@@BLE, push-on jt
U E
@@MJBE
U F
@@SPE
'spigot ends'
U G
@@PE/MJBE
U H
@@SPE/BLE, push-on jt
U I
@@PE/BLE, push-on jt
U J
@@PLE/BLSE, push-on jt
U K
@@PLE/MJBSE
U L
@@SPLE/BLSE, push-on jt
U M
@@BLE/SPE/BLE, push-on jt
U N
@@BLE/PE/BLE, push-on jt
U P
MJBE/PE/MJBE
U R
@@PE
'plain ends'
U Z
''
533
S-40
'Sch 40'
U C
S-80
'Sch 80'
U D
@@S-XS
'X-strong'
U E
S-160
Sch 160'
U G
S-XXS
'XX-strong'
U L
S-C50
Class 50'
U M
S-C51
'Class 51'
U N
S-C52
'Class 52'
U S
S-STD
'standard-weight'
U T
@@S-XH
'extra-heavy'
U U
S-SW
'service-weight'
U X
@@
''
! 0
1
2
! 1
2345678901234567890
DESCRIPTION
534
SHORT DESCRIPTION
U A
U Z
@@
''
U VAA
'ASTM-A74 w/preformed
rubber gasket per
ASTM-C564'
U VBA
'ANSI/AWWA-C110/A21.10,
double thickness cement
lined, asphalt coated,
push-on joint w/preformed
rubber gasket per
ANSI/AWWA-C111/A21.11'
U VBB
'ANSI/AWWA-C110/A21.10,
double thickness cement
lined, asphalt coated,
mechanical w/preformed
rubber gasket per
ANSI/AWWA-C111/A21.11,
gland & bolts'
U VBC
AWWA-C110 w/gskt
'ANSI/AWWA-C110/A21.10,
asphalt coated, push-on
joint w/preformed rubber
gasket per
ANSI/AWWA-C111/A21.11'
LONG
U VCA
@@ASTM-C700 w/polyurethane
compr coupl
'ASTM-C700 w/bonded
polyurethane compression
coupling per ASTM-C425'
U VCB
@@polyurethane/clay
'polyurethane/clay'
U VGH
U VGI
Valves
! 0
1
2
! 1
2345678901234567890
DESCRIPTION
! FIRST LETTER: V - VALVES
SHORT DESCRIPTION
V A
@@Gate valve
'Gate valve'
V B
@@Globe valve
'Globe valve'
V C
@@Check valve
'Check valve'
V D
@@Ball valve
'Ball valve'
V E
@@Plug valve
'Plug valve'
V F
@@Butterfly valve
'Butterfly valve'
V G
V H
Diaphragm valve
'Diaphragm valve'
V I
Control valve
'Control valve'
V J
Slide valve
'Slide valve'
V K
Knife valve
'Knife valve'
V L
@@Angle valve
'Angle valve'
V M
Sample valve
'Sampling valve'
V N
@@Needle valve
'Needle valve'
V O
@@Deluge valve
'Deluge valve'
V P
Pipeline valve
'Pipeline valve'
V R
Relief valve
'Relief valve'
V S
Stop check
'Stop check'
LONG
535
536
V T
V V
Instr valve
'Instrument valve'
V W
V X
'valve ??'
V Y
@@Y-globe valve
'Y-globe valve'
V A
@@CL150
'CL150'
V B
@@CL300
'CL300'
V C
@@CL400
'CL400'
V D
@@CL600
'CL600'
V E
@@CL900
'CL900'
V F
@@CL1500
'CL1500'
V G
CL2500
'CL2500'
V H
CL4500
'CL4500'
V K
CL75
'CL75'
V L
@@CL125
'CL125'
V M
CL250
'CL250'
V N
@@CL200
'CL200'
V O
CL2000
'CL2000'
V P
CL3000
'CL3000'
V Q
CL5000
'CL5000'
V R
CL10000
'CL10000'
V S
CL15000
'CL15000'
V T
CL20000
'CL20000'
V U
@@CL800
'CL800'
V V
3000 WOG
'3000 WOG'
V W
6000 WOG
'6000 WOG'
V X
'rating ??'
V A
@@FFFE
V B
@@RFFE
V D
V E
BE/FTE
V F
M SWE/FTE
MTE/FTE
V H
@@SWE/FTE
V J
@@RJFE
V K
MSWE/FSWE
V L
lens joint
V M
V N
V O
V P
V R
RFFE, 3 Ra finish
V S
@@SWE
'socketwelded ends'
V T
@@FTE
tube conn
'tubing connection'
V V
Victaulic ends
'Victaulic ends'
V W
@@BW
'buttwelded ends'
V X
'ends ??'
V A
@@carbon steel
'carbon steel'
V B
C-0.5Mo
'C-0.5Mo'
V C
@@1.25Cr
'1.25Cr'
V D
2.25Cr
'2.25Cr'
V E
@@5Cr
'5Cr'
V F
@@9Cr
'9Cr'
V G
12CR
'12Cr'
V H
other Cr
'other Cr'
V I
@@304 SS
'304 SS'
V J
@@304L SS
'304L SS'
V K
@@316 SS
'316 SS'
V L
@@316L SS
'316L SS'
V M
@@321 SS
'321 SS'
V N
@@347 SS
'347 SS'
537
H Gr SS
'H Gr.SS'
V R
400 SS
V S
@@low temp CS
V T
@@cast iron
'cast iron'
V U
@@ductile iron
'ductile iron'
V V
malleable iron
'malleable iron'
V W
@@Cu
'copper'
V X
@@Ni
'nickel'
V Y
Al
'aluminum'
V Z
538
V 2
@@thermoplastic
'thermoplastic'
V 3
thermoset plastic
'thermoset plastic'
V 4
non metalic
'non metalic'
V 5
@@lined
'lined'
V 6
coated
'coated'
V 9
'matl ??'
V A
@@trim 1
V B
@@trim 2
V C
trim 3
'trim 3'
V D
trim 4
'trim 4'
V E
@@trim 5
V F
trim 6
'trim 6'
V G
@@trim 7
V H
@@trim 8
V I
@@trim 9
V J
@@trim 10
V K
trim 11
'trim 11'
V L
@@trim 12
V M
@@trim 13
V N
trim 14
'trim 14'
V Q
V R
V S
V T
V V
V W
V X
'trim ??'
V Z
@@
''
V AA
V AB
V AC
V AD
V AE
V AF
V AG
V AH
V AI
V AJ
V AK
V AL
V AM
V AN
V AO
V AP
V AQ
V AR
V AS
V AT
V AU
V AV
V AW
V AX
V AY
V AZ
V BA
V BB
V BC
539
540
V BD
V BE
V BF
V BG
V BH
V BI
V CA
@@Crane 33
'Crane 33'
V CB
@@Crane 33 1/2
'Crane 33 1/2'
V CC
@@Crane 47
'Crane 47'
V CD
Crane 55
'Crane 55'
V CE
@@Crane 76
'Crane 76'
V CF
@@Crane 143
'Crane 143'
V CG
@@Crane 151
'Crane 151'
V CH
V CI
@@Crane 787
'Crane 787'
V CJ
Crane 1523
'Crane 1523'
V CK
@@Crane 7189
'Crane 7189'
V CL
@@Crane 9302
'Crane 9302'
V CM
@@Crane B-3655
'Crane B-3655'
V CN
@@Crane B-3663
'Crane B-3663'
V CO
V CP
V CQ
@@Crane 14 1/2 P
V CR
@@Crane 36
'Crane 36'
V CS
@@Crane 431 UB
V CT
V CU
@@Crane 88
'Crane 88'
V CW
V CX
@@Crane 137
'Crane 137'
V CY
@@Crane 76 1/2
'Crane 76 1/2'
V CZ
V DA
@@Crane 171
'Crane 171'
V DB
@@Crane 87
'Crane 87'
@@Crane 189
'Crane 189'
V DD
@@Crane 373
'Crane 373'
V EA
@@Rockwell 1925
'Rockwell 1925'
V EB
@@Rockwell 1945
'Rockwell 1945'
V EC
@@Rockwell 4149
'Rockwell 4149'
V ED
V EE
V EF
V EG
@@Rockwell 2245
'Rockwell 2245'
V EH
V EI
'Rockwell Mc CannaS301'
V EJ
@@Rockwell 2025
'Rockwell 2025'
V EK
@@Rockwell 2045
'Rockwell 2045'
V EL
@@Rockwell 4249
'Rockwell 4249'
V EM
@@Rockwell 2249
'Rockwell 2249'
V EN
@@Rockwell 4749
'Rockwell 4749'
V EO
V EP
V EQ
V ER
V ES
V ET
V EU
V EV
V EW
V EX
V EY
V EZ
V FA
V FB
V FC
@@Rockwell 1947
'Rockwell 1947'
V FW
Watts 900
Watts 900'
V FX
Watts 909
'Watts 909'
V GA
@@Smith 800
'Smith 800'
V GB
@@Smith 870
'Smith 870'
541
542
V GC
@@Smith 888
'Smith 888'
V GD
@@Smith 5870
'Smith 5870'
V GE
@@Smith 1500
'Smith 1500'
V GF
@@Smith 1570
'Smith 1570'
V GG
@@Smith 815
'Smith 815'
V GH
@@Smith 830
'Smith 830'
V GI
@@Smith G80
'Smith G80'
V GJ
@@Smith G87
'Smith G87'
V GK
@@Smith G150
'Smith G150'
V GL
@@Smith G157
'Smith G157'
V GM
@@Smith SB80
'Smith SB80'
V GN
@@Smith C150
'Smith C150'
V GO
@@Smith 860
'Smith 860'
V GP
@Smith G83
'Smith G83'
V GQ
@@Smith C83
'Smith C83'
V GR
Smith B80
'Smith B80'
V GS
Smith 411F
'Smith 411F'
V GT
Smith 411T
'Smith 411T'
V HA
V HB
V HP
Hancock 5505W
'Hancock 5505W'
V HQ
Hancock 7105W
'Hancock 7105W'
V IA
@@Jamesbury 4CB
'Jamesbury 4CB'
V IB
@@Jamesbury 5150
'Jamesbury 5150'
V IC
@@Jamesbury 5300
'Jamesbury 5300'
V ID
@@Jamesbury A11
'Jamesbury A11'
V IE
@@Jamesbury 4AB
'Jamesbury 4AB'
V IF
@@Jamesbury A11
'Jamesbury A11'
V JA
@@Stockham D623
'Stockham D623'
V JB
@@Stockham D512
'Stockham D512'
V JC
@@Stockham D931
'Stockham D931'
V KA
Hex HG-651
'Hex HG-651'
V KB
Hex HG-463
'Hex HG-463'
Hex HG-461
'Hex HG-461'
V KD
Hex HB-241
'Hex HB-241'
V KE
Hex HB-521
'Hex HB-521'
V KF
Hex HB-501
'Hex HB-501'
V KH
Hex HN-491
'Hex HN-491'
V KI
Hex HM-571
'Hex HM-571'
V KJ
Hex HM-451
'Hex HM-451'
V KK
Hex HM-131
'Hex HM-131'
V LA
V LB
V LC
V LD
V LE
V LF
V MA
@@Aloyco 2214-A
'Aloyco 2214-A'
V MB
@@Aloyco 2314-A
'Aloyco 2314-A'
V MC
@@Aloyco 374
'Aloyco 374'
V MD
@@Aloyco 377
'Aloyco 377'
V ME
@@Aloyco 114
'Aloyco 114'
V MF
@@Aloyco 117
'Aloyco 117'
V MG
@@Aloyco 317
'Aloyco 317'
V MH
@@Aloyco 2117
'Aloyco 2117'
V MI
@@Aloyco 110
'Aloyco 110'
V MJ
@@Aloyco 114EB
'Aloyco 114EB'
V MK
@@Aloyco 117EB
'Aloyco 117EB'
V ML
@@Aloyco 2117EB
'Aloyco 2117EB'
V MM
@@Aloyco 314
'Aloyco 314'
V MN
@@Aloyco 314EB
'Aloyco 314EB'
V MO
@@Aloyco 317EB
'Aloyco 317EB'
V MP
@@Aloyco 2317A
'Aloyco 2317A'
V MQ
@@Aloyco 2374
'Aloyco 2374'
V MR
@@Aloyco 2377
'Aloyco 2377'
V MS
@@Aloyco 110EB
'Aloyco 110EB'
V MT
@@Aloyco 2110
'Aloyco 2110'
543
@@Aloyco 2114
'Aloyco 2114'
V MV
Aloyco 2117A
'Aloyco 2117A'
V MW
Aloyco 2210A
'Aloyco 2110A'
V MX
Aloyco 4217A
'Aloyco 4217A'
V MY
Aloyco 4227
'Aloyco 4227'
V MZ
Aloyco 4210A
'Aloyco 4210A'
V NA
Aloyco 4214A
'Aloyco 4214A'
V NB
Aloyco 2317
'Aloyco 2317'
V NC
Aloyco 4327
'Aloyco 4327'
V ND
Aloyco 4314A
'Aloyco 4314A'
V NE
Aloyco 374
'Aloyco 374'
V NF
Aloyco 4387
'Aloyco 4387'
V NG
Aloyco 4374
'Aloyco 4374'
V NH
Aloyco 62
'Aloyco 62'
V OA
@@Pacific 160
'Pacific 160'
V OB
@@Pacific 180
'Pacific 180'
V OC
@@Pacific 380
'Pacific 380'
V OD
@@Pacific 660
'Pacific 660'
V OE
@@Pacific 680
'Pacific 680'
V OF
@@Pacific 1584
'Pacific 1584'
V OG
@@Pacific 2155
'Pacific 2155'
V OH
@@Pacific 2355
'Pacific 2355'
V OI
@@Pacific 2655
'Pacific 2655'
V OJ
544
@@Pacific 55515
'Pacific 55515'
V OK
@@Pacific 56009
'Pacific 56009'
V OL
@@Pacific 56015
'Pacific 56015'
V OM
Pacific 58009
'Pacific 58009'
V ON
@@Pacific 58815
'Pacific 58815'
V OO
V OP
@@Pacific 21555
'Pacific 21555'
V OQ
@@Pacific 360
'Pacific 360'
V OR
@@Pacific 55509
'Pacific 55509'
V OS
@@Pacific 58809
'Pacific 58809'
V OT
Pacific 350
'Pacific 350'
@@Pacific 2955
'Pacific 2955'
V OV
@@Pacific 21553
'Pacific 21553'
V OW
Pacific 56509
'Pacific 56509'
V OX
@@Pacific 1550
'Pacific 1550'
V OY
@@Pacific 960
'Pacific 960'
V OZ
@@Pacific 984
'Pacific 984'
V QA
@@Pratt PIVA
'Pratt PIVA'
V QB
@@Pratt GROUNDHOG
'Pratt GROUNDHOG'
V QK
V QL
V QM
V QN
V QO
V QP
V QQ
V QR
V QS
V RA
@@Vogt 22461
'Vogt 22461'
V RB
@@Vogt 15373
'Vogt 15373'
V RC
Vogt 15401
'Vogt 15401'
V RD
Vogt SWS74
'Vogt SWS74'
V RJ
@@Centerline 504
'Centerline 504'
V RK
@@Centerline A
'Centerline A'
V RL
@@Centerline LT
'Centerline LT'
V RN
V SA
Powell 1331
'Powell 1331'
V UA
Demco NE
'Demco NE'
V UB
Demco NF
'Demco NF'
V UC
Demco WF
'Demco WF'
V UF
Mueller 31
'Mueller 31'
V UG
Mueller 61
'Mueller 61'
545
V VP
@@Powhatan 18-157
'Powhatan 18-157'
V YA
Yarway 3486-R
'Yarway 3486-R'
V YB
Yarway 3488-R
'Yarway 3488-R'
V AA
@@
''
V AB
V AC
V AD
V BA
@@RFTBE
V BB
@@RFTBCSE,
V BC
@@RFTBEWG
V BF
@@FFTBE
V BG
V BH
V BI
V BJ
V BK
546
@@FFTBSCEWG
V BN
@@RFTBE, NACE
V BP
@@FFTBEWG
V BQ
@@FFTBSCEWG
V BZ
V CA
thru-bolt, w/GO
V CB
V CC
V CD
heat jkt/thru-bolt
V CE
@@NACE, GO
V CI
no Cu alloys, GO
V CK
thru-bolt, no Cu alloys
V CL
547
V CN
high temp/GO
'high temperature/right
angle gear oper'
V CP
high temp/GO/D&T
'high temperature/right
angle gear oper D&T machine
bolts'
V CT
V CY
V DA
V DB
548
D & T mach/no Cu
V DC
V DD
V DE
V DF
V DG
V DH
V DI
V DJ
V DL
V DM
V DN
V DO
V DP
V DQ
V EA
V EC
epoxy lined
'epoxy lined'
V ED
V EE
V EF
549
550
V EG
V FA
built in bypass
'built in bypass'
V FB
V FL
V GC
GO/one side
V GH
GO
'gear operator'
V GP
GO, parallel
V GR
V GX
V GY
gear/right angle
V GZ
gear/parallel
V JA
jacketed
'jacketed'
V MK
3 way
V ML
4 way
V RA
@@no Cu alloys
V RB
no Cu alloys
V RC
chlorine service
'chlorine service'
V RD
DEA/MEA service
'DEA/MEA service'
V RE
@@NACE
'NACE service'
V RN
V RO
oxygen service
'oxygen service'
V SD
SWE at locn D
'socketwelded connection at
location D'
V SE
SWE at locn E
'socketwelded connection at
location E'
SWE at locn G
'socketwelded connection at
location G'
V TA
tap at locn A
V TC
tap at locn C
V TD
tap at locn D
V TG
tap at locn G
V TH
V TU
V WA
wrench
Welded Fittings
! 0 1 2
! 1 2345678901234567890 SHORT DESCRIPTION LONG DESCRIPTION
! FIRST LETTER: W - WELDED FITTINGS
W AA
W AB
W AC
W AD
W AG
W AH
W BA
W BC
W BD
W BE
W CA
W DA
W DB
W DC
W OA
W OB
551
OC
OD
OE
OF
OG
OH
OI
OJ
OK
OS
OT
OU
OV
OX
W ZA
W ZB
W __
Thredolet
Elbolet
"
Nipolet 3.5 long "
"
Nipolet 4.5 long "
"
Nipolet 5.5 long "
"
Nipolet 6.5 long "
Latrolet
Weld boss
Weld saddle
Sweepolet
Flat weldolet
Flat sockolet
Flat thredolet
Weldolet, calculation
required
Sockolet
Sockolet, calculation
required
Thredolet
Thredolet, calculation
required
@@Concentric reducer, Concentric reducer,
BE
beveled ends
@@Eccentric reducer, BE Eccentric reducer,
beveled ends
@@Concentric swage
Concentric swage
@@Eccentric swage
Eccentric swage
@@Tee, BE
Tee, beveled ends
@@Reducing tee, BE
Reducing tee, beveled
ends
Weld 45 deg lateral
Weld 45 deg lateral
fitting
Reducing weld 45 deg
Reducing weld 45 deg
lateral
lateral fitting
Weld retn bend LR
Weld return bend long
radius
Weld retn bend SR
Weld return bend short
radius
Weld cross
Weld cross
Reducing weld cross
Reducing weld cross
Weld 45 lateral reinf Weld 45 deg lateral
reinforced
Buttweld
Buttweld
@@Reinforcing weld
Reinforcing weld
Standard fittings
Cap/ell/tee
W
W
@@BE
BE LT
W OY
W OZ
W RA
W RB
W
W
W
W
SA
SB
TA
TB
W TL
W TM
W UA
W UB
W XA
W XB
W YA
552
AA
AB
@@Thredolet
@@Elbolet
Nipolet 3.5 long
Nipolet 4.5 long
Nipolet 5.5 long
Nipolet 6.5 long
@@Latrolet
Weld boss
Weld saddle
Sweepolet
@@Flat weldolet
@@Flat sockolet
Flat thredolet
Weldolet
beveled ends
bevel ends long
tangent
AZ
BA
CA
CB
CC
CD
CE
CF
CG
FB
FD
FF
FG
FH
FI
FJ
W
W
W
SA
TA
ZZ
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
AA
AB
AC
AD
AF
AG
AH
AI
AJ
AK
AL
AM
AN
AO
AW
@@PE
plain ends
@@MTE
male threaded ends
MTLE/BSE
thread large end &
bevel small end
@@BLE/MTSE
beveled large x male
threaded small ends
GLE/TSE
groove large end & THD
small end
MTLE/PSE
thread large end &
plain small end
@@PLE/MTSE
plain large x male
thread small ends
@@BLE/PSE
bevel large x plain
small ends
@@RFFE
raised face flanged
ends
RFFE, 125 Ra finish
raised face flanged
ends, 125 Ra finish
RFFE, 125-250 Ra finish raised face flanged
ends, 125-250 Ra finish
RFFE, 63-250 Ra finish raised face flanged
ends, 63-250 Ra finish
RFFE, 63-125 Ra finish raised face flanged
ends, 63-125 Ra finish
RFFE, 3 Ra finish
raised face flanged
ends, 3 Ra finish
RJFE
ring joint flanged
ends
@@SWE
socketwelded ends
@@FTE
female threaded ends
@@
S-5S
S-10S
S-40S
@@S-80S
S-10
S-20
S-30
S-40
S-60
S-80
S-100
S-120
S-140
@@S-160
@@bore
Sch 5S
Sch 10S
Sch 40S
Sch 80S
Sch 10
Sch 20
Sch 30
Sch 40
Sch 60
Sch 80
Sch 100
Sch 120
Sch 140
Sch 160
[???]
553
554
BA
BB
BC
BD
BQ
BR
BS
CA
CB
CC
CD
CE
CF
CG
CH
CI
CJ
CK
CL
CM
CN
CO
CP
CQ
CR
CS
CT
CU
CV
CW
CX
DD
DF
DH
DJ
DL
DN
EA
EB
EC
ED
EE
S-LW
S-STD
S-XS
@@S-XXS
@@CL3000
@@CL6000
@@CL9000
0.125 "
0.188 "
0.25 "
0.312 "
0.375 "
0.438 "
0.5 "
0.562 "
0.625 "
0.688 "
0.75 "
0.812 "
0.875 "
0.938 "
1 "
1.062 "
1.125 "
1.188 "
1.25 "
1.375 "
1.5 "
1.625 "
1.781 "
1.875 "
0.281 "
0.906 "
1.312 "
1.406 "
1.594 "
1.75 "
2 "
2.125 "
2.25 "
2.375 "
2.5 "
light-weight
standard-weight
X-strong
XX-strong
CL3000
CL6000
CL9000
0.125 "
0.188 "
0.25 "
0.312 "
0.375 "
0.438 "
0.5 "
0.562 "
0.625 "
0.688 "
0.75 "
0.812 "
0.875 "
0.938 "
1 "
1.062 "
1.125 "
1.188 "
1.25 "
1.375 "
1.5 "
1.625 "
1.781 "
1.875 "
0.281 "
0.906 "
1.312 "
1.406 "
1.594 "
1.75 "
2 "
2.125 "
2.25 "
2.375 "
2.5 "
EF
EH
FE
MA
MB
MC
MD
ME
MF
MG
MH
MI
MJ
MK
ML
MM
MN
MO
MP
MQ
MR
MS
MT
MU
MV
NP
NR
PA
PB
PC
PD
PE
PF
PG
PH
PI
PJ
PK
PL
PM
PN
PO
2.625 "
2.875 "
3.5 "
2.0 mm
2.5 mm
3.0 mm
3.5 mm
4.0 mm
4.5 mm
5.0 mm
6.0 mm
7.0 mm
8.0 mm
10.0 mm
12.0 mm
16.0 mm
20.0 mm
25.0 mm
30.0 mm
35.0 mm
40.0 mm
50.0 mm
60.0 mm
80.0 mm
100.0 mm
32.0 mm
45.0 mm
3.2 mm
4.8 mm
6.4 mm
7.9 mm
9.5 mm
11.1 mm
12.7 mm
14.3 mm
15.9 mm
17.5 mm
19.1 mm
20.6 mm
22.2 mm
23.8 mm
25.4 mm
2.625 "
2.875 "
3.5 "
2.0 mm
2.5 mm
3.0 mm
3.5 mm
4.0 mm
4.5 mm
5.0 mm
6.0 mm
7.0 mm
8.0 mm
10.0 mm
12.0 mm
16.0 mm
20.0 mm
25.0 mm
30.0 mm
35.0 mm
40.0 mm
50.0 mm
60.0 mm
80.0 mm
100.0 mm
32.0 mm
45.0 mm (1.771) "
3.2 mm (0.125) "
4.8 mm (0.188) "
6.4 mm (0.25) "
7.9 mm (0.312) "
9.5 mm (0.375) "
11.1 mm (0.438) "
12.7 mm (0.5) "
14.3 mm (0.562) "
15.9 mm (0.625) "
17.5 mm (0.688) "
19.1 mm (0.75) "
20.6 mm (0.812) "
22.2 mm (0.875) "
23.8 mm (0.938) "
25.4 mm (1) "
555
556
PP
PQ
PR
PS
PV
PW
PX
PZ
QA
QE
QF
QG
ZW
ZZ
W
W
AAA
AAB
AAC
AAD
W
W
W
AAG
AAH
AAI
AAJ
AAP
W
W
W
W
W
W
W
ABB
ABL
AFA
AFB
AFE
AFH
ASA
ASB
ASC
ASD
27.0 mm
28.6 mm
30.2 mm
31.8 mm
39.0 mm
56.0 mm
41.0 mm
29.0 mm
43.0 mm
47.0 mm
26.0 mm
19.0 mm
thk per reqn
@@
@@ASTM-A234-WPB
ASTM-A234-WPB, alum
ASTM-A234 Gr.WPB
ASTM-A234 Gr.WPB,
aluminized per
ASTM-A676
ASTM-A234-WPB, galv
ASTM-A234 Gr.WPB,
galvanized
ASTM-A234-WPB T&W
ASTM-A234 Gr.WPB,
treated & wrapped
ASTM-A105, alum
ASTM-A105, aluminized
@@ASME-SA234-WPB
ASME-SA234 Gr.WPB
ASTM-A234-WPB
ASTM-A234 Gr.WPB,
fully stress relieved
ASTM-A234-WPB alum T&W ASTM-A234 Gr.WPB,
aluminized, treated &
wrapped
@@ASTM-A234-WPB
ASTM-A234 Gr.WPB
Dur-O-Lok
Dur-O-Lok fitting
ASTM-A350 LF2
ASTM-A350 Gr.LF2
@@ASTM-A420 WPL6
ASTM-A420 Gr.WPL6
@@ASTM-A105
ASTM-A105
@@ASTM-A350 LF2
ASTM-A350 Gr.LF2
@@ASME-SA105
ASME-SA105
ASTM-A105, galv
ASTM-A105, galvanized
ASTM-A234-WPB
ASTM-A234 Gr.WPB,
seamless
ASTM-A234-WPB, alum
ASTM-A234 Gr.WPB,
aluminized, per
ASTM-A676, seamless
ASTM-A234-WPB, galv
ASTM-A234 Gr.WPB,
galvanized, seamless
ASTM-A234-WPB T&W
ASTM-A234 Gr.WPB,
treated & wrapped,
ASE
ASF
ASG
ASH
ASK
W
W
AZA
EAY
EAZ
EFA
ESA
W
W
FAC
FAF
W
W
W
FAH
FAL
FAM
W
W
FAT
FBD
W
W
FFC
FFE
FFF
FFI
W
W
FFL
FFR
W
W
FFT
FSA
FSB
FSC
seamless
ASME-SA234-WPB
ASME-SA234 Gr.WPB,
seamless
ASTM-A234-WPB alum T&W ASTM-A234 Gr.WPB,
aluminized, treated &
wrapped, seamless
ASTM-A420 WPL6
ASTM-A420 Gr.WPL6,
seamless
ASTM-A420-WPL6
ASTM-A420 Gr.WPL6
seamless, special
testing required
ASTM-A234-WPB
ASTM-A234 Gr.WPB,
seamless, special
testing required
@@carbon steel
carbon steel
ASTM-A234-WP1W
ASTM-A234 Gr.WP1W,
carbon moly
ASTM-A234-WP1
ASTM-A234 Gr.WP1,
carbon moly
ASTM-A182-F1
ASTM-A182 Gr.F1,
carbon moly
ASTM-A234-WP1
ASTM-A234 Gr.WP1,
carbon moly, seamless
@@ASTM-A234-WP11
ASTM-A234 Gr.WP11
ASTM-A234-WP22
ASTM-A234 Gr.WP22,
2.25Cr-1Mo
@@ASTM-A234-WP5
ASTM-A234 Gr.WP5
@@ASTM-A234-WP9
ASTM-A234 Gr.WP9
@@ASTM-A234-WP11
ASTM-A234 Gr.WP11
Dur-O-Lok
1.25Cr-0.5Mo Dur-O-Lok
fitting
ASTM-A182-F5
ASTM-A182 Gr.F5
ASTM-A336-F21
ASTM-A336 Gr.F21,
2.25Cr-1Mo
@@ASTM-A182-F11
ASTM-A182 Gr.F11
ASTM-A234-WP11W
ASTM-A234 Gr.WP11W,
1.25Cr-0.5Mo
ASTM-A182-F22
ASTM-A182 Gr.F22,
2.25Cr-1Mo
ASTM-A182-F5A
ASTM-A182 Gr.F5A,
5Cr-0.5Mo
@@ASTM-A182-F9
ASTM-A182 Gr.F9
ASTM-A182-F11
ASTM-A182 Gr.F11,
1.25Cr-0.5Mo
@@ASTM-A182-F5
ASTM-A182 Gr.F5
ASTM-A234-WP9
ASTM-A234 Gr.WP9,
9Cr-1Mo, seamless
ASTM-A234-WP11
ASTM-A234 Gr.WP11,
1.25Cr-0.5Mo, seamless
ASTM-A234-WP22
ASTM-A234 Gr.WP22,
2.25Cr-1Mo, seamless
557
558
FSD
ASTM-A234-WP5
W
W
W
FZA
GAA
GAF
@@chrome steel
@@ASME-SA234-WP11
ASME-SA234-WP22
W
W
GFC
GFF
@@ASME-SA182-F11
ASME-SA182-F22
GSA
ASME-SA234-WP11
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
IFA
IFB
IFF
IFG
IFJ
IFL
IFY
IFZ
IIA
IIB
IIC
IID
IIE
IIF
IIG
IIH
IIJ
IIK
IIL
IIM
IIN
IIS
IIY
IIZ
@@ASTM-A182-F304
@@ASTM-A182-F304L
@@ASTM-A182-F316
ASTM-A182-F316L
@@ASTM-A182-F321
ASTM-A182-F347
ASTM-A182-F347H
ASTM-A182-F304H
ASTM-A403-WP304S
ASTM-A403-WP304LS
ASTM-A403-WP304LWX
ASTM-A403-WP304WX
ASME-SA403-WP316L
ASTM-A403-WP316S
ASTM-A403-WP316LS
ASTM-A403-WP316LWX
ASTM-A403-WP321S
ASTM-A403-WP316WX
ASTM-A403-WP347
ASTM-A403-WP321WX
ASTM-A403-WP347WX
ASTM-A403-WP304HWX
ASTM-A403-WP347H
ASTM-A403-WP304S
IKA
ASTM-A451-HF modified
W
W
W
W
W
W
IKB
IKD
IKE
IKF
IZA
OAA
@@ASTM-A403-WP304
@@ASTM-A403-WP304L
@@ASTM-A403-WP316
@@ASTM-A403-WP321
@@stainless steel
ASTM-B366-WPNIC,
ASTM-A234 Gr.WP5,
5Cr-0.5Mo, seamless
chrome alloy steel
ASME-SA234 Gr.WP11
ASME-SA234 Gr.WP22,
2.25Cr-1Mo
ASME-SA182 Gr.F11
ASME-SA182 Gr.F22,
2.25Cr-1Mo
ASME-SA234 Gr.WP11,
1.25Cr-0.5Mo, seamless
ASTM-A182 Gr.F304
ASTM-A182 Gr.F304L
ASTM-A182 Gr.F316
ASTM-A182 Gr.F316L
ASTM-A182 Gr.F321
ASTM-A182 Gr.F347
ASTM-A182 Gr.F347H
ASTM-A182 Gr.F304H
ASTM-A403 Gr.WP304S
ASTM-A403 Gr.WP304LS
ASTM-A403 Gr.WP304LWX
ASTM-A403 Gr.WP304WX
ASME-SA403 Gr.WP316L
ASTM-A403 Gr.WP316S
ASTM-A403 Gr.WP316LS
ASTM-A403 Gr.WP316LWX
ASTM-A403 Gr.WP321S
ASTM-A403 Gr.WP316WX
ASTM-A403 Gr.WP347
ASTM-A403 Gr.WP321WX
ASTM-A403 Gr.WP347WX
ASTM-A403 Gr.WP304HWX
ASTM-A403 Gr.WP347H
ASTM-A403 Gr.WP304S,
special testing
required
ASTM-A451 Gr.HF
modified, Spec 400-31
ASTM-A403 Gr.WP304
ASTM-A403 Gr.WP304L
ASTM-A403 Gr.WP316
ASTM-A403 Gr.WP321
stainless steel
ASTM-B366 Gr.WPNIC UNS
OAB
OSA
OSB
PAA
PAB
PFA
SAA
SSA
WAA
WAB
WAC
WAD
WAE
WSA
WSB
WXX
___
Incoloy
ASTM-B564, Incoloy
Gaskets
! 0 1 2
! 1 2345678901234567890 SHORT DESCRIPTION LONG DESCRIPTION
! FIRST LETTER: X - GASKETS
X A
559
C
D
E
F
G
X H
X I
X J
X K
X L
X M
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
560
N
R
S
T
U
V
AA
AB
AC
AD
AE
AF
AG
AX
BA
BB
BC
BD
BE
BH
CA
CB
CD
CE
DA
@@ANSI-B16.5 CL150
@@ANSI-B16.5 CL300
ANSI-B16.5 CL400
@@ANSI-B16.5 CL600
@@ANSI-B16.5 CL900
@@ANSI-B16.5 CL1500
ANSI-B16.5 CL2500
rating per reqn
@@API-605 CL150
@@API-605 CL300
API-605 CL400
API-605 CL600
API-605 CL900
API-605 CL75
@@MSS-SP-44 CL150
@@MSS-SP-44 CL300
@@MSS-SP-44 CL600
MSS-SP-44 CL900
ANSI-B16.1 CL25
ANSI-B16.5 CL150
ANSI-B16.5 CL300
ANSI-B16.5 CL400
ANSI-B16.5 CL600
ANSI-B16.5 CL900
ANSI-B16.5 CL1500
ANSI-B16.5 CL2500
rating ??
API-605 CL150
API-605 CL300
API-605 CL400
API-605 CL600
API-605 CL900
API-605 CL75
MSS-SP-44 CL150
MSS-SP-44 CL300
MSS-SP-44 CL600
MSS-SP-44 CL900
ANSI-B16.1 CL25
DB
DC
DD
SA
SB
SC
SD
SE
SF
SG
SH
TB
TC
TD
TE
TF
TG
ZZ
ANSI-B16.1 CL125
ANSI-B16.1 CL250
ANSI-B16.1 CL800
@@CL150
CL300
CL400
CL600
CL900
CL1500
CL2500
@@AWWA-C207 Cl.E
Taylor Forge CL75
Taylor Forge CL125
Taylor Forge CL125LW
Taylor Forge CL175
Taylor Forge CL250
Taylor Forge CL350
ANSI-B16.1 CL125
ANSI-B16.1 CL250
ANSI-B16.1 CL800
CL150
CL300
CL400
CL600
CL900
CL1500
CL2500
AWWA-C207 Cl.E
Taylor Forge CL75
Taylor Forge CL125
Taylor Forge CL125LW
Taylor Forge CL175
Taylor Forge CL250
Taylor Forge CL350
X
X
X
X
X
A
B
C
D
E
X
X
X
X
X
X
X
F
H
I
J
K
L
N
@@ANSI-B16.20
@@0.0625" thk
0.125 thk "
0.1875 thk "
0.25 thk "
0.5 thk "
1.6 mm thk
X
X
X
X
X
X
X
X
X
X
O
P
Q
R
S
T
U
V
X
Z
3.2
4.8
6.4
3.2
1.6
3.2
4.8
6.4
thk
0.0625 thk
0.125 thk
0.1875 thk API-601 "
0.25 thk "
0.125 compressed thk
API 601 "
ANSI-B16.20
0.0625" thk
0.125 thk "
0.1875 thk "
0.25 thk "
0.5 thk "
1.6 mm thk,
ANSI-B16.21
3.2 mm thk, API-601
4.8 mm thk, API-601
6.4 mm thk
3.2 mm thk, API 601
1.6 mm thk
3.2 mm thk
4.8 mm thk
6.4 mm thk
thk ??
mm thk
mm thk
mm thk
mm thk
mm thk
mm thk
mm thk
mm thk
per reqn
561
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
562
AA
AB
AC
AD
AF
AG
AH
AI
AJ
AK
AL
AM
AN
AO
AW
BA
BB
BC
BD
CA
CB
CC
CD
CE
CF
CG
CH
CI
CJ
CK
CL
CM
CN
CO
CP
CQ
CR
CS
DD
MA
MB
S-5S
S-10S
S-40S
S-80S
S-10
S-20
S-30
S-40
S-60
S-80
S-100
S-120
S-140
S-160
[???]|bore to match|
S-LW
S-STD
S-XS
S-XXS
0.125 "
0.188 "
0.25 "
0.312 "
0.375 "
0.438 "
0.5 "
0.562 "
0.625 "
0.688 "
0.75 "
0.812 "
0.875 "
0.938 "
1 "
1.062 "
1.125 "
1.188 "
1.25 "
0.281 "
2.0 mm
2.5 mm
Sch 5S
Sch 10S
Sch 40S
Sch 80S
Sch 10
Sch 20
Sch 30
Sch 40
Sch 60
Sch 80
Sch 100
Sch 120
Sch 140
Sch 160
[???]
light-weight
standard-weight
X-strong
XX-strong
0.125 "
0.188 "
0.25 "
0.312 "
0.375 "
0.438 "
0.5 "
0.562 "
0.625 "
0.688 "
0.75 "
0.812 "
0.875 "
0.938 "
1 "
1.062 "
1.125 "
1.188 "
1.25 "
0.281 "
2.0 mm
2.5 mm
MC
MD
ME
MF
MG
MH
MI
MJ
MK
MM
MN
MO
MP
MQ
MR
MS
MT
MU
MV
PA
PB
PD
PE
PF
PG
PH
PI
PJ
PK
PL
PM
PN
PO
PP
PQ
PR
PS
ZZ
3.0 mm
3.5 mm
4.0 mm
4.5 mm
5.0 mm
6.0 mm
7.0 mm
8.0 mm
10.0 mm
16.0 mm
20.0 mm
25.0 mm
30.0 mm
35.0 mm
40.0 mm
50.0 mm
60.0 mm
80.0 mm
100.0 mm
3.2 mm
4.8 mm
6.4 mm
9.5 mm
11.1 mm
12.7 mm
14.3 mm
15.9 mm
17.5 mm
19.1 mm
20.6 mm
22.2 mm
23.8 mm
25.4 mm
27.0 mm
28.6 mm
30.2 mm
31.8 mm
@@
3.0 mm
3.5 mm
4.0 mm
4.5 mm
5.0 mm
6.0 mm
7.0 mm
8.0 mm
10.0 mm
16.0 mm
20.0 mm
25.0 mm
30.0 mm
35.0 mm
40.0 mm
50.0 mm
60.0 mm
80.0 mm
100.0 mm
3.2 mm (0.125) "
4.8 mm (0.188) "
6.4 mm (0.25) "
9.5 mm (0.375) "
11.1 mm (0.438) "
12.7 mm (0.5) "
14.3 mm (0.562) "
15.9 mm (0.625) "
17.5 mm (0.688) "
19.1 mm (0.75) "
20.6 mm (0.812) "
22.2 mm (0.875) "
23.8 mm (0.938) "
25.4 mm (1) "
27.0 mm (1.062) "
28.6 mm (1.125) "
30.2 mm (1.188) "
31.8 mm (1.25) "
X
X
X
AAA
AAB
AAC
low CS
low CS, 120 BHN max
@@5Cr-0.5Mo, 130 BHN max 5Cr-0.5Mo, 130 BHN max
347 SS
347 SS
563
564
X
X
X
X
X
AAD
AAE
AAF
AAG
ALR
X
X
X
X
AZY
AZZ
HAA
HAB
ICA
ICB
ICC
ICD
ICE
LAA
LAB
X
X
X
X
PAA
PAD
PAE
PAF
QAB
QAC
QAD
QRB
QRC
QRF
QSA
12Cr TP410
321 SS
316 SS
@@347 SS, 140 BHN max
316 SS, special
QSB
QSC
QSD
QSF
@@304/Teflon-F, CS
center ring, 304 IR
QSG
QSH
QSJ
@@304/graph-F, CS center
ring
@@304/Teflon-F, CS
center ring
@@316/graph-F, CS center
ring, 316 IR
QSK
QSL
QSM
QSN
QSO
347/graph filled
QSP
Inconel/graph filled
QSS
QST
QSU
QSV
QSW
QSX
@@321/graph, CS center
ring
@@321/graph, CS center
ring, 321 IR
QUE
316/mica/graph CS center
ring
316/mi/grph CS center
ring, 316 IR
@@316/graph-F, CS center
ring
@@304/graph-F, CS center
ring, 304 IR
@@neoprene sheet
565
Bolting
!
!
!
Y
0 1 2
1 2345678901234567890 SHORT DESCRIPTION LONG DESCRIPTION
FIRST LETTER: Y - BOLTING
A
@@Bolt set for FFFE
Bolt set for flat face
joint
joint
B
@@Bolt set for RFFE
Bolt set for raised
joint
face joint
F
Bolt set for lap joint Bolt set for lap
joint
H
Jackscrew pair
Jackscrew pair
J
Bolt set for RJFE joint Bolt set for ring
joint flanged end
L
Bolt set for lens joint Bolt set for lens
joint
M
Miscellaneous
bolting
Z
@@
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
JA
JB
JC
JD
JE
JF
JG
JH
JI
JJ
JK
JL
JM
JN
JO
JP
JQ
JR
JS
JT
JU
JV
JW
JX
Y
Y
Y
Y
Y
Y
566
JY
JZ
KA
KB
KC
KD
KE
LA
ZZ
C
Y
Y
Y
Y
Y
FA
FB
FC
FD
FE
1 lg "
1.25 lg "
@@1.5 lg "
@@1.75 lg "
@@2 lg "
1 long "
1.25 long "
1.5 long "
1.75 long "
2 long "
567
568
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
FF
FG
FH
FI
FJ
FK
FL
FM
FN
FO
FP
FQ
FR
FS
FT
FU
FV
FX
FY
FZ
GA
GB
GC
GD
MC
@@2.25 lg "
@@2.5 lg "
@@2.75 lg "
@@3 lg "
@@3.25 lg "
@@3.5 lg "
@@3.75 lg "
@@4 lg "
@@4.25 lg "
@@4.5 lg "
4.75 lg "
5 lg "
@@5.25 lg "
5.5 lg "
@@5.75 lg "
6 lg "
@@6.25 lg "
@@6.5 lg "
6.75 lg "
7 lg "
7.25 lg "
7.5 lg "
7.75 lg "
8 lg "
+15 mm
MD
+20 mm
ME
+25 mm
MG
+40 mm
MI
+50 mm
ZZ
@@
AAA
AAB
Y
Y
AAW
AAX
@@ASTM-A307-B w/A563-A
hvy hex nuts
ASTM-A307-B, w/A563-A
nuts
ASTM-A307-B
ASTM-A307-B
FFB
@@ASTM-A193-B8C Cl.1
w/A194-8C hv hx nuts
FFC
ASTM-A193-B7, w/A194-2H
nuts, cad plated
FFD
@@ASTM-A193-B8C Cl.1
w/A194-8C hv hx nuts
FFF
@@ASTM-A193-B7
w/A194-2H hvy hex nts
FFG
ASTM-A193-B7
FFL
@@ASTM-A193-B7M
w/A194-2H hvy hex nuts
FFM
ASTM-A193-B7M,
w/A194-2HM hvy hex nuts
FFN
ASTM-A193-B7M,
w/A194-2H hvy hex nuts
FFO
ASTM-A193-B7M,
w/A194-2HM hvy hex nuts
Y
Y
FFP
FFT
@@ASTM-A193-B7M
ASTM-A193-B7, w/A194-2H
hvy hex nuts
FFU
ASTM-A193-B8 Cl.2,
w/A194-8 hvy hex nuts
FFV
ASTM-A193-B8 Cl.2,
w/A194-8 hvy hex nuts
Y
Y
FFW
FFX
@@ASTM-A193-B7
ASTM-A193-B8 Cl.2
FFY
ASTM-A193-B8 Cl.2
FFZ
FGT
ASTM-A193-B8C
Cl.2,w/A194-8C hvy hex
nuts
ASTM-A193-B16, w/A194-3
569
FGU
@@ASTM-A193-B16
w/A194-4 hvy hex nuts
Y
FGV
ASTM-A193-B16, w/A194-3
hvy hex nuts
Y
Y
FYF
GGC
ASTM-A194-2H
@@ASME-SA193-B7
w/SA194-2H hvy hex nuts
GGD
ASME-SA193-B7,
w/SA194-2H hvy hex nuts
GGE
ASME-SA193-B16,
w/SA194-3 hvy hex nuts
VGGF
570
@@ASME-SA193-B16
w/SA194-4 hvy hex nuts
GGG
ASME-SA193-B16,
w/SA194-3 hvy hex nuts
ASTM-A453-660 Cl.B
IIA
ILU
@@ASTM-A320-B8 Cl.2,
w/A194-8 hvy hx nuts
ILV
ASTM-A320-B8 Cl.2,
w/A194-8 hvy hex nuts
Y
Y
ILW
ILX
ASTM-A320-B8 Cl.2
ASTM-A320-B8 Cl.2
MLF
@@ASTM-A320-L7 w/A194-4
hvy hex nuts
Y
Y
MLG
MLH
@@ASTM-A320-L7
ASTM-A320-L7
MLT
ASTM-A320-L7, w/A194-4
hvy hex nuts
OAA
ASTM-B164
571
APPENDIX E
Delivered Equations
The thickness and branch reinforcement logic for the following equations are hardcoded in the
software.
EJ01
Source - ANSI-B31.1.1986 [Power Piping]
Thickness logic from paragraph 104.1, equation 3
Reinforcement logic from paragraph 104.3.1(D)
EL01
Source - ANSI-B31.3c.1986 [Chemical Plant and Petroleum Refinery Piping]
Thickness logic from paragraph 304.1, equation 3a
Reinforcement logic from paragraph 304.3.3 & Code - Appendix H
The following considerations apply to both thickness equations and branch reinforcement
calculations.
Pressures and temperatures used in thickness/branch reinforcement calculations are derived
from data in the Piping Design Database. Both normal and alternate pressure and
temperature conditions are considered. If actual values exist for the normal design or the
alternate design pressure/temperatures, the corresponding operating conditions are ignored.
If default values exist for BOTH sets of design conditions, both normal and alternate operating
conditions are used. At least one complete set of conditions must be defined.
Once the proper pressure and temperature sets are determined, their units of measure are
converted to those used in the Temperature-Pressure Table associated with the Piping
573
Materials Class to which the component belongs. Conversions are performed using the
procedures and conversion factors defined for the Units of Measure in Appendix F.
Only positive pressure is considered. The system reports an error if you request a thickness
calculation involving a vacuum condition (negative pressure).
Independent sets of thickness/reinforcement calculations are carried out for each applicable
pressure/temperature set. In each calculation set, table values that are temperature
dependent are determined on the basis of the temperature applicable to the calculation set
being considered. The thicker calculated thickness is used.
Thickness Equations
The following considerations apply to thickness equations.
Thickness calculations are triggered by specifying an equation name in the
Schedule/Thickness attribute of the Piping Commodity Specification Data. An asterisk (*)
followed by a name (of the form xyyy) defines the specific calculation or table lookup to be
used for wall thickness. The letters that form this code have the following meaning:
x alphanumeric code that defines the equation to use in the calculation. Possible values
and their definitions are:
If this character is C, the schedule/thickness for the applicable end of the component is
determined by calculations using the thickness equation defined in the
DEFAULT_WALL_THICK_EQUATION attribute of the Piping Materials Class database
table.
If the code is any character other than C, the schedule/thickness for the applicable end of
the component is determined by calculations using the thickness equation with the name
EX.
yyy casting, joint or structural grade quality factor (E) times 100.
This factor is one of the parameters used in the thickness calculation. If you are defining a
calculation to be performed on a seamless fitting (E=1) but want to match the thickness for the
mating welded pipe (E=0.85), the quality factor for the pipe should be entered here.
For components with ends having different nominal diameters, independent sets of thickness
determinations are performed for each NPD. One or more ends may need to calculated, as
determined by specific *xyyy entries in the Commodity Item entity. The larger thickness
(calculated or predefined) is used. For example:
A 20" x 10" reducer is defined in the Piping Commodity Table to have a *xyyy 20" end and
a 0.55" thick, 10" end. The calculation of the 20" end results in a 0.5" thickness. A 0.55"
thick reducer is used.
A 24" x 20" reducer is defined in the Piping Commodity Table to have a *XYYY 24" end
and a *XYYY 20" end. The calculation of the 24" end results in a 0.6" thickness. The
calculation of the 20" end results in a 0.5" thickness. A 0.6" thick reducer is used.
All thickness calculations involve a casting, joint, or structural grade quality factor (E).
The value for this factor is YYY/100, where YYY is defined in the entry *XYYY made under
the Schedule Thickness attribute for the Commodity Item under consideration.
Branch Reinforcement
The following considerations apply to branch reinforcement calculations.
The need to perform a branch reinforcement calculation is triggered by
the placement of a generic branch component with the actual item name determined from
a branch table. (See Branch Insertion Tables.)
574
the presence of more than one item name in the Preferred Branch AABBCC Codes fields
of the applicable branch table.
the applicable branch reinforcement being either a reinforcing weld or a reinforcing pad.
All calculations involve a casting, joint, or structural grade quality factor (E). The value for this
factor is YYY/100, where YYY is defined in the Modifier attribute for entries with an item name
of PIPING.
The fillet welds joining reinforcing pads to the header and to the branch are considered in
determining the available reinforcement area.
Spec Access
The execution of a pipe wall thickness calculation is performed when the variable PIPE_OD_n is
encountered in the physical data definition of a pipe or component. Therefore, pipe outside
diameter must be calculated or retrieved from a table before the wall thickness can be used as
part of a table name.
After the actual thickness is calculated, it is compared against the thickness range in the Materials
table and the retirement thickness in the Thickness Data table. The system uses the greater of
these values as the uncorroded wall thickness. Then the system adds the corrosion allowance
from the PMC, the thread thickness from the wall thickness table, and the mill tolerance from the
Materials table. This revised thickness is compared against the minimum thickness value in the
Thickness Data table. The larger of these two values is compared against the preferred
thickness value in the Thickness Data table, and the next largest preferred value is used for table
look-ups and is stored in the TDB.
If the Thickness Data table uses schedules as preferred thickness, the schedules are translated to
an actual thickness by a table look-up from a table of the form
MALWT//Term_type//shc_thick//generic_flag//weight_code
and output 2 gives the actual wall thickness.
575
APPENDIX F
Codelists
This section details the codelists used in PDS.
The data contained within this appendix is for informational purposes only and may not
exactly match the codelists delivered with the product.
577
Codelists
In This Appendix
General Comments ........................................................................ 579
Comments Specific to Units of Measure Codelist Sets ................. 579
CL31, Object Types for Orthographic Drawings (40) .................... 581
CL35, Approval Status (10) ........................................................... 583
CL36, Structural Approval Status (15) ........................................... 583
CL37, HVAC Approval Status (10) ................................................ 584
CL50, Hold Status (10) .................................................................. 584
CL69, Equipment Divisions/Form Code (99) ................................. 584
CL125, Fluid Code/Connector Type (999) ..................................... 585
CL130, Construction Status (15) ................................................... 589
CL145, Materials Grade (4500) ..................................................... 589
CL148, Piping Materials Class Description (31999) ...................... 625
CL160, Responsibility (25)............................................................. 636
CL180, Fabrication Category (99) ................................................. 636
CL190, Coating Requirements (99) ............................................... 637
CL200, Heat Tracing Requirements (10)....................................... 637
CL210, Heat Tracing Media (60) ................................................... 638
CL220, Insulation Purpose (40) ..................................................... 639
CL230, Cleaning Requirements (99) ............................................. 639
CL330, CP Type/Termination/Preparation (999) ........................... 639
CL332, Schedule / Thickness Override ......................................... 643
CL340, Safety Classification (99) .................................................. 645
CL360, Stress Analysis Requirements (15) ................................... 645
CL365, Reporting Requirements (25) ............................................ 645
CL366, Requirement to Reconstruct (10) ...................................... 646
CL380, Piping Component Type (2500) ........................................ 646
CL390, Action (40) ......................................................................... 655
CL400, Option (999) ...................................................................... 655
CL420, Piping Component Type/Source (25)................................ 664
CL425, Piping/Tubing Type (25) .................................................... 664
CL430, Instrument Component Type/Source (25)......................... 664
CL499, Piping Notes (999) ............................................................ 664
CL530, Accessory/Item Type (125) ............................................... 667
CL550, Operator/Actuator Type (200) ........................................... 667
CL570, Design Standard (200) ...................................................... 669
CL572, Wall Thickness Equation ................................................... 669
CL575, Geometry Standard (31999) ............................................. 669
CL576, Table Suffix/End Standard - Green (999) ......................... 684
CL577, Table Suffix/End Standard - Red (999) ............................. 688
CL578, Weight Code (399) ............................................................ 692
CL990, Types of Piping Commodity Data Forms .......................... 694
CL999, Standard Note Title (2000) ................................................ 695
CL1010, Area Units (25) ................................................................ 696
CL1028, Mass Units (40) ............................................................... 697
CL1056, Temperature Units (15) ................................................... 697
CL1064, Pressure Units (40) ......................................................... 698
CL1074, Density Units (35)............................................................ 699
CL1100, Weld Type (100).............................................................. 699
CL1162, Force Units (40) .............................................................. 699
CL1201, Drawing Scale (540)........................................................ 700
CL1202, Drawing Size (199).......................................................... 700
578
Codelists
CL1203, Interference Manager Approval Status (99) .................... 700
CL1204, Interference Clash Type .................................................. 700
CL1205, Interference Manager Action (10) ................................... 703
CL1207, Interference Manager Approval Method (10) .................. 703
CL1208, Clash Checking Option ................................................... 703
CL1209, Clash Checking Volume Filter Option ............................. 703
CL1310, Report Source (99).......................................................... 703
CL1312, Report Type (999) ........................................................... 703
CL1410, Design Review Type (10) ................................................ 704
CL1605, Model Status ................................................................... 704
CL1610, Force Units for FrameWorks Plus (40) ........................... 704
CL1620, Drawing View Directions (7) ............................................ 705
CL1630, Drawing View Composition Status (4) ............................ 705
CL1710, Document Source (99) .................................................... 705
CL1720, Document Type (999) ..................................................... 706
CL1900, Isometric Drawing Type .................................................. 708
CL2000, PD_Draw Document Type (999) ..................................... 709
General Comments
Codelist sets in this document define the values for all codelisted attributes used in the PDS Piping
Task which are specific to US plant design practices.
You can add, delete, or revise codelists sets to reflect your own practices, terminology and
language. A task user, however, cannot revise a codelist set from a work session. Revisions to
a codelist set, can only be made in the General RDB or Standard Note Library.
In listings that follow, the maximum number of entries that may be expected for a specific codelist
set is shown in parenthesis following the name of the codelist set.
For PDS users that wish to modify codelist files delivered with the PDS software to reflect their
own practices, two approaches are possible:
Make the modifications within the range of codelist numbers defined in the codelist library
delivered with the PDS software. This has the advantage of resulting in the best-organized
set of codelisted definitions. The disadvantage is that numbers added by the User may
conflict with numbers added in future versions of software.
Increase the maximum number of entries allowed for the codelist set and make additions to it
in the range of extended numbers. This will minimize possible conflicts assigned numbers
but will require compiling of the codelists and of the associated databases.
Values enclosed in brackets [ ] in pages that follow represent descriptive information. The values
stored in the codelist sets will exclude this bracketed information from the codelist descriptions.
The net length of a codelist entry cannot exceed 50 characters. Other considerations may,
however, require that a shorter description be made. For example:
For the P&ID Task, the total compressed length of a label part can not exceed 36 characters.
The formats of specification type reports for the Instrument Task require that applicable
codelist descriptions do not exceed 25 characters.
579
Codelists
The tables in this document include the following information.
Codelist set
Codelist no
Unit type
This code is not explicitly shown in the tables. The unit type equals
the number of the codelist set minus 1000. For example, reference
to unit type 28 refers to "mass".
Quantity name
Unit name:
Several unit names are provided for a given codelist set. Any of
these names can be used to define the quantity.
Conversion to
destination unit:
580
Codelists
B is the factor in the column captioned Factor B.
The distinction between upper case and lower case symbols is very important. For example:
K= kelvin
k= kilo= 10^3
M= mega= 10^6
m= milli= 10^-3 (when m is used as a prefix)
m= metre (when m is used alone)
N= newton
n= nano= 10^-9
In editing any of the codelist sets for units, do not change the meaning of existing codelist values.
In all codelist sets for units, a blank space is provided as the first character in the unit name. The
blank space is used to silence the units in the formation of labels.
Nomenclature:
Symbol
Name
Quantity
bar
bar
pressure
degC
degree
Celsius
temperature
gram
mass
kg
kilogram
mass
metre
length
min
minute
time
Pa
pascal
pressure
metric ton
mass
581
Codelists
101
110
120
124
128
130
135
140
=
=
=
=
=
=
=
=
Piping
205
207
210
215
220
=
=
=
=
=
'Equipment
'Equipment
'Equipment
'Equipment
'Equipment
'Equipment
'Equipment
'Equipment
Group'
Nozzle'
Platform'
Handrail'
Penetration'
Stair'
Ladder'
Davit'
Segment'
Component'
Specialty'
Support'
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
'HVAC
'HVAC
'HVAC
'HVAC
'HVAC
'HVAC
'HVAC
'HVAC
'HVAC
'HVAC
'HVAC
'HVAC
'HVAC
Coil Data'
Connector Data'
Damper Data'
Diffuser Data'
Duct Data'
DEquipment Data'
Filter Data'
Fitting Data'
Grille Data'
Hood Data'
Humidifier Data'
Register Data'
Terminal Devices'
582
=
=
=
=
=
=
=
=
=
'EERWAY
'EERWAY
'EERWAY
'EERWAY
'EERWAY
'EERWAY
'EERWAY
'EERWAY
'EERWAY
Connect Point'
OneLine'
Straight'
Fitting'
Space Envelope'
To_Equipment'
To_Support'
Eqp Panel'
Duct Bank'
Codelists
reserved
reserved
reserved
reserved
for
for
for
for
'approved'
'not approved'
'approved'
'not approved'
1 = [Blank]
2 = 'A =Approved'
3 = 'NA=Not approved'
=
=
=
=
=
'New'
'Existing'
'Future'
'User 1'
'User 2'
583
Codelists
=
=
=
=
'New'
'Existing'
'Dismantle'
'Future'
584
=
=
=
=
=
=
=
=
'A=
'B=
'C=
'D=
'E=
'F=
'H=
'I=
All'
Vessels'
Heat transfer'
Mechanical'
Civil/Structural'
Piping'
Electrical'
Other'
Codelists
=
=
=
=
=
=
=
=
=
=
'A'
'AC'
'AE'
'AI'
'AO'
'AP'
'APU'
'AR'
'AS'
'AZ'
[Air]
[Combustion air]
[Aeration air]
[Instrument air]
[Operational air]
[Plant air]
[Purge air]
[Regeneration air]
[Starting air]
[Other air]
71
75
79
83
87
91
100
=
=
=
=
=
=
=
'C'
'CA'
'CE'
'CF'
'CLP'
'CPR'
'CZ'
[Refrigerant]
[Ammonia refrigerant]
[Ethylene refrigerant]
[Freon refrigerant]
[LP refrigerant]
[Propylene refrigerant]
[Other refrigerant]
101
103
105
107
109
111
113
115
117
119
121
123
125
127
128
130
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
'D'
'DC'
'DCH'
'DGR'
'DOW'
'DP'
'DPH'
'DS'
'DSP'
'DST'
'DW'
'DWS'
'DX'
[Blank]
[Blank]
'DZ'
[Sewer]
[Caustic sewer]
[Chemical sewer]
[Drain to grade]
[Oily water sewer]
[Process sewer]
[Heated process sewer]
[Sanitary sewer]
[Press sanitary sewer]
[Storm sewer]
[Clean water sewer]
[Sour water sewer]
[Acid sewer]
[Storm, oily water or sanitary sewer]
[Storm or oily water sewer]
[Other sewer]
161 = 'F'
[Foam]
585
Codelists
586
191
194
197
198
200
203
206
209
212
215
218
221
224
227
230
233
236
239
242
245
250
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
'G'
'GCD'
'GCL'
'GCN'
'GF'
'GG'
'GH'
'GHS'
'GI'
'GLP'
'GM'
'GN'
'GNI'
'GOX'
'GP'
'GR'
'GS'
'GSO'
'GSW'
'GW'
'GZ'
[Gas]
[Carbon dioxide gas]
[Chlorine gas]
[Chlorination gas]
[Fuel gas]
[Flue gas]
[Hydrogen gas]
[Hydrogen sulphide gas]
[Inert gas]
[LP gas]
[Make-up gas]
[Natural gas]
[Nitrogen gas]
[Oxygen gas]
[Purge gas]
[Reformed gas]
[Synthesis gas]
[Sour gas]
[Sweet gas]
[Waste gas
[Other gas]
341
346
351
356
370
=
=
=
=
=
'K'
'KG'
'KF'
'KD'
'KZ'
[Solvent]
[Glycol]
[Furfural]
[Dewaxing]
[Other solvent]
401
402
405
409
413
417
421
425
429
433
434
440
444
448
452
460
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
'M'
[Blank]
'MAA'
'MAC'
'MAW'
'MC5'
'MCL'
'MEO'
'MHC'
'MIA'
'MIB'
'MLA'
'MMA'
'MS'
'MSL'
'MZ'
[Chemical]
[Chemical injection]
[Anhydrous ammonia]
[Aluminum chloride]
[Aqueous ammonia]
[0-50% caustic solution]
[Dry chlorine]
[Ethylene oxide]
[Hydrogen chloride]
[Inhibitor A]
[Inhibitor B]
[Lube oil additives]
[Methyl alcohol]
[Sulfur]
[Liquid sulfur]
[Other chemical]
Codelists
491
493
495
497
499
500
503
505
507
509
511
513
515
520
=
=
=
=
=
=
=
=
=
=
=
=
=
=
'O'
'OD'
'ODS'
'OF'
'OFR'
'OFS'
'OH'
'OL'
'OLS'
'OS'
'OSO'
'OSW'
'OWS'
'OZ'
[Oil]
[Diesel fuel oil]
[Dry slop oil]
[Flushing oil]
[Fuel oil return]
[Fuel oil supply]
[Hydraulic oil]
[Lube]
[Lube and seal oil]
[Seal oil]
[Sour oil]
[Sweet oil]
[Wet slop oil]
[Other oil]
521
522
524
527
530
533
536
539
542
545
550
=
=
=
=
=
=
=
=
=
=
=
'P'
[Blank]
'PA'
'PAS'
'PB'
'PH'
'PHH'
'PHW'
'PL'
'PS'
'PZ'
[Process]
[Special process]
[Process w/ rich/lean amine]
[Process w/ severe amine]
[Process w/ benzene]
[Process w/ H2]
[Process w/ H2 & H2S]
[Process w/ aqueous H2S]
[Low temperature process]
[Process w/ S]
[Other process]
581 = 'RA'
591 = 'RF'
610 = 'RZ'
[Relief to atmosphere]
[Relief to flare]
[Other relief]
611
613
615
617
621
623
625
627
629
631
633
635
640
=
=
=
=
=
=
=
=
=
=
=
=
=
'S'
[Blank]
[Blank]
[Blank]
'SE'
'SH'
'SL'
'SM'
'SN'
'SS'
'SV'
'SX'
'SZ'
[Steam]
[Boiler feed water or steam]
[Boiler feed water, steam or condensate]
[Steam or condensate]
[Extr press CL1500 steam]
[High press CL900 steam]
[Low press CL150 steam]
[Med press CL600 steam]
[Nor press CL300 steam]
[Superheated steam]
[Vacuum steam]
[Exhaust CL125 steam]
[Other steam]
641
643
645
647
649
651
653
655
660
=
=
=
=
=
=
=
=
=
'SC'
'SCA'
'SCE'
'SCH'
'SCL'
'SCM'
'SCN'
'SCV'
'SCZ'
[Steam condensate]
[Atmospheric CL125 steam condensate]
[Extr press CL1500 steam condensate]
[High press CL900 steam condensate]
[Low press CL150 steam condensate]
[Med press CL600 steam condensate]
[Nor press CL300 steam condensate]
[Vacuum steam condensate]
[Other steam condensate]
587
Codelists
588
721
731
741
750
751
753
755
757
759
761
763
764
765
767
768
771
772
773
775
777
779
781
783
785
786
789
791
792
795
797
798
801
803
805
807
809
811
812
815
817
819
830
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
'V'
'VA'
'VF'
'VZ'
'W'
'WB'
'WBA'
'WBB'
'WC'
[Blank]
'WCH'
'WCL'
'WCF'
'WCR'
'WCS'
'WPT'
[Blank]
'WDM'
'WFA'
'WFI'
'WFU'
'WG'
'WGL'
'WGR'
'WGS'
'WH'
'WHR'
'WHS'
'WI'
'WIR'
'WIS'
'WK'
'WN'
'WP'
'WR'
'WS'
'WSR'
'WSS'
'WT'
'WU'
'WW'
'WZ'
[Vent]
[Vent to atmosphere]
[Vent to flare]
[Other vent]
[Water]
[Boiler feed water]
[Ballast water]
[Water boiler blowdown]
[Cooling water]
[Cooling or utility water]
[Chlorinated water]
[Chlorine in water]
[Clarified water]
[Cooling water return]
[Cooling water supply]
[Potable water]
[Potable water or instrument air]
[Demineralized water]
[Aboveground fire water]
[Filtered water]
[Underground fire water]
[Glycol water]
[Gland water]
[Glycol water return]
[Glycol water supply]
[Hot water]
[Hot water return]
[Hot water supply]
[Chilled water]
[Chilled water return]
[Chilled water supply]
[Treated water]
[Brine water]
[Process water]
[Raw water]
[Sea water]
[Sea water return]
[Sea water supply]
[Test water]
[Utility water]
[Waste water]
[Other water]
831
835
839
843
847
851
853
860
=
=
=
=
=
=
=
=
'X'
'XH'
'XN'
'XSD'
'XS3'
'XS8'
'XS9'
'XZ'
[Acid]
[Hydrofluoric acid]
[Nitric acid]
[Dilute sulfuric acid]
[30% sulfuric acid]
[75-80% sulfuric acid]
[93-97% sulfuric acid]
[Other acid]
Codelists
861
865
869
873
877
881
890
=
=
=
=
=
=
=
'Y'
'YA'
'YG'
'YH'
'YL'
'YW'
'YZ'
[Catalyst]
[Catalyst addition]
[General catalyst]
[Catalyst w/ H2]
[Catalyst lift lines]
[Catalyst withdrawal lines]
[Other catalyst]
950
951
953
955
956
960
961
999
=
=
=
=
=
=
=
=
'ODPC'
'OUPC'
'UODPC'
'ODIC'
'OUIC'
'OVPC'
'OSPC'
'TERM'
=
=
=
=
=
=
=
=
[Blank]
'New'
'Existing'
'Revamp'
'Relocate'
'Temporary'
'Dismantle'
'Future'
589
Codelists
Irons,
10 =
12 =
15 =
16 =
17 =
18 =
19 =
20 =
21 =
22 =
23 =
25 =
30 =
31 =
32 =
35 =
40 =
41 =
42 =
43 =
44 =
45 =
46 =
47 =
48 =
55 =
60 =
62 =
70 =
75 =
76 =
590
10-99
'A47-32510'
'A47-35018'
'A48-20'
'A48-25'
'A48-30'
'A48-35'
'A48-40'
'A48-45'
'A48-50'
'A48-55'
'A48-60'
'A74'
'A126-A'
'A126-B'
'A126-C'
'A197'
'A278-20'
'A278-25'
'A278-30'
'A278-35'
'A278-40'
'A278-50'
'A278-60'
'A278-70'
'A278-80'
'A338'
'A395-Ductile'
'A395-Ferritic Ductile'
'A571'
'AWWA-C110-Ductile'
'AWWA-C151-Ductile'
Codelists
Carbon
110 =
114 =
116 =
118 =
120 =
122 =
124 =
135 =
140 =
142 =
144 =
150 =
160 =
162 =
164 =
170 =
180 =
182 =
183 =
184 =
185 =
186 =
187 =
188 =
190 =
191 =
192 =
193 =
194 =
195 =
200 =
202 =
210 =
212 =
214 =
216 =
218 =
220 =
230 =
234 =
240 =
241 =
242 =
243 =
244 =
245 =
250 =
252 =
254 =
264 =
266 =
270 =
272 =
Steels, 100-499
'API-5L-A'
'API-5L-A25'
'API-5L-B'
'API-5L-X42'
'API-5L-X46'
'API-5L-X52'
'API-5L-X65'
'A36'
'A53-A'
'A53-B'
'A53-Type F'
'A105'
'A106-A'
'A106-B'
'A106-C'
'A120'
'A134-A36'
'A134-A283-A'
'A134-A283-B'
'A134-A283-C'
'A134-A283-D'
'A134-A285-A'
'A134-A285-B'
'A134-A285-C'
'A134-A570-30'
'A134-A570-33'
'A134-A570-36'
'A134-A570-40'
'A134-A570-45'
'A134-A570-50'
'A135-A'
'A135-B'
'A139-A'
'A139-B'
'A139-C'
'A139-D'
'A139-E'
'A179'
'A181-CL60'
'A181-CL70'
'A211-A570-30'
'A211-A570-33'
'A211-A570-36'
'A211-A570-40'
'A211-A570-45'
'A211-A570-50'
'A216-WCA'
'A216-WCB'
'A216-WCC'
'A234-WPB'
'A234-WPC'
'A283-A'
'A283-B'
591
Codelists
274
276
280
282
284
290
293
295
298
300
302
305
310
312
320
321
322
323
325
327
334
340
342
344
346
350
352
354
356
360
361
362
363
364
365
370
372
375
380
390
392
394
396
398
400
402
404
406
408
410
420
422
424
426
592
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
'A283-C'
'A283-D'
'A285-A'
'A285-B'
'A285-C'
'A333-1'
'A333-6'
'A334-1'
'A334-6'
'A350-LF1'
'A350-LF2'
'A352-LCB'
'A369-FPA'
'A369-FPB'
'A381-Y35'
'A381-Y42'
'A381-Y46'
'A381-Y48'
'A381-Y50'
'A381-Y52'
'A420-WPL6'
'A515-55'
'A515-60'
'A515-65'
'A515-70'
'A516-55'
'A516-60'
'A516-65'
'A516-70'
'A520-30'
'A520-33'
'A520-36'
'A520-40'
'A520-45'
'A520-50'
'A524-I'
'A524-II'
'A537-CL1'
'A587'
'A671-CA55'
'A671-CB60'
'A671-CB65'
'A671-CB70'
'A671-CC60'
'A671-CC65'
'A671-CC70'
'A671-CD70'
'A671-CE55'
'A671-CE60'
'A671-CK75'
'A672-A45'
'A672-A50'
'A672-A55'
'A672-B55'
Codelists
428
430
432
434
436
438
440
442
444
446
448
460
464
=
=
=
=
=
=
=
=
=
=
=
=
=
'A672-B60'
'A672-B65'
'A672-B70'
'A672-C55'
'A672-C60'
'A672-C65'
'A672-C70'
'A672-D70'
'A672-E55'
'A672-E60'
'A672-N75'
'A691-CMS75'
'A691-CMSH70'
593
Codelists
Low and Intermediate Alloy Steels, 500-899
510 = 'A182-F1'
512 = 'A182-F2'
514 = 'A182-F5'
516 = 'A182-F5a'
518 = 'A182-F6a Cl.1'
519 = 'A182-F6a Cl.2'
520 = 'A182-F6a Cl.3'
521 = 'A182-F6a Cl.4'
523 = 'A182-F6b'
524 = 'A182-F7'
526 = 'A182-F9'
528 = 'A182-F11'
530 = 'A182-F12'
532 = 'A182-F21'
534 = 'A182-F22'
536 = 'A182-F22a'
540 = 'A202-A'
542 = 'A202-B'
550 = 'A203-A'
552 = 'A203-B'
554 = 'A203-D'
556 = 'A203-E'
560 = 'A204-A'
562 = 'A204-B'
564 = 'A204-C'
576 = 'A217-C5'
578 = 'A217-C12'
580 = 'A217-CA15'
582 = 'A217-WC1'
584 = 'A217-WC4'
586 = 'A217-WC5'
588 = 'A217-WC6'
590 = 'A217-WC9'
600 = 'A225-A'
602 = 'A225-B'
610 = 'A234-WP1'
614 = 'A234-WP5'
616 = 'A234-WP7'
618 = 'A234-WP9'
620 = 'A234-WP11'
622 = 'A234-WP12'
624 = 'A234-WP22'
630 = 'A302-A'
632 = 'A302-B'
634 = 'A302-C'
636 = 'A302-D'
644 = 'A333-3'
646 = 'A333-4'
648 = 'A333-7'
650 = 'A333-8'
652 = 'A333-9'
664 = 'A334-3'
666 = 'A334-7'
594
Codelists
668
670
680
682
684
686
687
690
692
694
696
698
700
702
710
720
722
724
730
740
742
744
746
748
750
752
754
756
758
760
761
770
771
774
775
778
779
780
781
782
783
784
785
786
787
794
798
800
802
804
806
808
810
812
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
'A334-8'
'A334-9'
'A335-P1'
'A335-P2'
'A335-P5'
'A335-P5b'
'A335-P5c'
'A335-P7'
'A335-P9'
'A335-P11'
'A335-P12'
'A335-P15'
'A335-P21'
'A335-P22'
'A350-LF3'
'A352-LC1'
'A352-LC2'
'A352-LC3'
'A353'
'A369-FP1'
'A369-FP2'
'A369-FP3b'
'A369-FP5'
'A369-FP7'
'A369-FP9'
'A369-FP11'
'A369-FP12'
'A369-FP21'
'A369-FP22'
'A385-7 Cl.1'
'A385-7 Cl.2'
'A387-2 Cl.1'
'A387-2 Cl.2'
'A387-5 Cl.1'
'A387-5 Cl.2'
'A387-9 Cl.1'
'A387-9 Cl.2'
'A387-11 Cl.1'
'A387-11 Cl.2'
'A387-12 Cl.1'
'A387-12 Cl.2'
'A387-21 Cl.1'
'A387-21 Cl.2'
'A387-22 Cl.1'
'A387-22 Cl.2'
'A420-WPL3'
'A420-WPL8'
'A426-CP1'
'A426-CP2'
'A426-CP5'
'A426-CP5b'
'A426-CP7'
'A426-CP9'
'A426-CP11'
595
Codelists
814
816
817
820
822
830
832
835
840
842
850
852
854
860
862
864
866
868
870
872
874
876
878
596
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
'A426-CP12'
'A426-CP15'
'A426-CPCA15'
'A426-CP21'
'A426-CP22'
'A553-Type I'
'A553-Type II'
'A645'
'A671-CF70'
'A671-CF71'
'A672-L65'
'A672-L70'
'A672-L75'
'A691-CM65'
'A691-CM70'
'A691-CM75'
'A691-0.5Cr'
'A691-1Cr'
'A691-1.25Cr'
'A691-2.25Cr'
'A691-3Cr'
'A691-5Cr'
'A691-9Cr'
Codelists
Stainless Steels, 900-1324
920 = 'A167-301'
922 = 'A167-302'
923 = 'A167-302B'
926 = 'A167-304'
927 = 'A167-304L'
930 = 'A167-305'
932 = 'A167-308'
934 = 'A167-309'
935 = 'A167-309S'
938 = 'A167-310'
939 = 'A167-310S'
942 = 'A167-316'
943 = 'A167-316L'
946 = 'A167-317'
947 = 'A167-317L'
950 = 'A167-321'
952 = 'A167-347'
954 = 'A167-348'
960 = 'A182-F10'
964 = 'A182-F304'
965 = 'A182-F304H'
966 = 'A182-F304L'
968 = 'A182-F310'
970 = 'A182-F316'
971 = 'A182-F316H'
972 = 'A182-F316L'
974 = 'A182-F321'
975 = 'A182-F321H'
978 = 'A182-F347'
979 = 'A182-F347H'
982 = 'A182-F348'
983 = 'A182-F348H'
990 = 'A240-X8M'
992 = 'A240-302'
994 = 'A240-304'
995 = 'A240-304L'
996 = 'A240-304H'
998 = 'A240-305'
1000 = 'A240-309S'
1004 = 'A240-310S'
1006 = 'A240-316'
1007 = 'A240-316L'
1010 = 'A240-317'
1011 = 'A240-317L'
1014 = 'A240-321'
1016 = 'A240-347'
1018 = 'A240-348'
1020 = 'A240-405'
1022 = 'A240-410'
1023 = 'A240-410S'
1026 = 'A240-429'
1028 = 'A240-430'
1040 = 'A268-TP329'
597
Codelists
1044
1046
1048
1050
1051
1054
1056
1060
1061
1064
1065
1066
1070
1071
1072
1074
1076
1078
1079
1080
1082
1084
1085
1088
1089
1092
1095
1100
1102
1104
1106
1108
1110
1112
1113
1114
1116
1118
1120
1122
1124
1126
1128
1130
1140
1141
1144
1146
1148
1149
1152
1154
1156
1160
598
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
'A268-TP405'
'A268-TP409'
'A268-TP410'
'A268-TP430'
'A268-TP430Ti'
'A268-TP443'
'A268-TP446'
'A269-TP304'
'A269-TP304L'
'A269-TP316'
'A269-TP316L'
'A270-TP316L'
'A312-TP304'
'A312-TP304H'
'A312-TP304L
'A312-TP309'
'A312-TP310'
'A312-TP316'
'A312-TP316H'
'A312-TP316L'
'A312-TP317'
'A312-TP321'
'A312-TP321H'
'A312-TP347'
'A312-TP347H'
'A312-TP348'
'A351-CA15'
'A351-CF3'
'A351-CF3A'
'A351-CF3M'
'A351-CF8'
'A351-CF8A'
'A351-CF8C'
'A351-CF8M'
'A351-CF10'
'A351-CF10MC'
'A351-CN7M'
'A351-CH8'
'A351-CH10'
'A351-CH20'
'A351-CK20'
'A351-HK30'
'A351-HK40'
'A351-HT30'
'A358-304'
'A358-304L'
'A358-309S'
'A358-310S'
'A358-316'
'A358-316L'
'A358-321'
'A358-347'
'A358-348'
'A376-16-8-2H'
Codelists
1162
1163
1166
1167
1170
1171
1174
1175
1178
1179
1190
1191
1192
1194
1196
1198
1199
1200
1202
1204
1205
1206
1207
1210
1220
1222
1224
1226
1228
1230
1232
1234
1240
1241
1244
1245
1248
1249
1252
1253
1260
1262
1264
1266
1268
1270
1272
1280
1282
1284
1300
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
'A376-TP304'
'A376-TP304H'
'A376-TP316'
'A376-TP316H'
'A376-TP321'
'A376-TP321H'
'A376-TP347'
'A376-TP347H'
'A376-TP348'
'A376-TP348H'
'A403-WP304'
'A403-WP304H'
'A403-WP304L'
'A403-WP309'
'A403-WP310'
'A403-WP316'
'A403-WP316H'
'A403-WP316L'
'A403-WP317'
'A403-WP321'
'A403-WP321H'
'A403-WP347'
'A403-WP347H'
'A403-WP348'
'A409-TP304'
'A409-TP309'
'A409-TP310'
'A409-TP316'
'A409-TP317'
'A409-TP321'
'A409-TP347'
'A409-TP348'
'A430-FP304'
'A430-FP304H'
'A430-FP316'
'A430-FP316H'
'A430-FP321'
'A430-FP321H'
'A430-FP347'
'A430-FP347H'
'A451-CHP10'
'A451-CHP20'
'A451-CPF8C'
'A451-CPF8M'
'A451-CPF10MC'
'A451-CPH8'
'A451-CPK20'
'A452-TP304H'
'A452-TP316H'
'A452-TP347H'
'ASME SA479-316L'
599
Codelists
Copper
1325 =
1330 =
1331 =
1334 =
1335 =
1338 =
1339 =
1342 =
1346 =
1350 =
1354 =
1356 =
1358 =
1362 =
1363 =
1364 =
1368 =
1369 =
1370 =
1374 =
1375 =
1376 =
1380 =
1381 =
1382 =
1386 =
1387 =
1392 =
1393 =
1398 =
1399 =
1404 =
1408 =
1410 =
1412 =
1414 =
1416 =
1418 =
1422 =
1430 =
1432 =
1434 =
1436 =
1438 =
1440 =
1442 =
1450 =
1452 =
1456 =
1458 =
1462 =
1463 =
1466 =
600
Codelists
1467
1472
1474
1476
1478
1480
1482
1484
1486
1488
1490
1492
1494
1496
1498
1500
1502
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
'B467
'B584
'B584
'B584
'B584
'B584
'B584
'B584
'B584
'B584
'B584
'B584
'B584
'B584
'B584
'B584
'B584
601
Codelists
Nickel
1560 =
1561 =
1564 =
1565 =
1568 =
1572 =
1573 =
1574 =
1576 =
1577 =
1578 =
1582 =
1586 =
1587 =
1590 =
1591 =
1594 =
1595 =
1596 =
1600 =
1601 =
1604 =
1605 =
1606 =
1607 =
1610 =
1611 =
1614 =
1615 =
1616 =
1620 =
1624 =
1626 =
1628 =
1630 =
1632 =
1634 =
1636 =
1638 =
1642 =
1643 =
1646 =
1648 =
1650 =
1652 =
1654 =
1656 =
1658 =
1660 =
1664 =
1666 =
1670 =
1672 =
602
Codelists
1676
1680
1684
1688
1700
1702
1704
1706
1708
1710
1714
1718
1722
1724
1726
1728
1730
1732
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
603
Codelists
Aluminum Alloys 1775-2299
1780 = 'B26-356.0 temper T6'
1782 = 'B26-356.0 temper T71'
1784 = 'B26-443.0 temper F'
1790 = 'B209-1060 temper 0'
1792 = 'B209-1060 temper H12'
1794 = 'B209-1060 temper H14'
1796 = 'B209-1060 temper H112'
1798 = 'B209-1100 temper 0'
1800 = 'B209-1100 temper H12'
1802 = 'B209-1100 temper H14'
1804 = 'B209-1100 temper H112'
1806 = 'B209-3003 temper 0'
1808 = 'B209-3003 temper H12'
1810 = 'B209-3003 temper H14'
1812 = 'B209-3003 temper H112'
1814 = 'B209-3004 temper 0'
1816 = 'B209-3004 temper H32'
1818 = 'B209-3004 temper H34'
1820 = 'B209-3004 temper H112'
1822 = 'B209-5050 temper 0'
1824 = 'B209-5050 temper H32'
1826 = 'B209-5050 temper H34'
1828 = 'B209-5050 temper H112'
1830 = 'B209-5052 temper 0'
1832 = 'B209-5052 temper H32'
1834 = 'B209-5052 temper H34'
1836 = 'B209-5052 temper H112'
1838 = 'B209-5652 temper 0'
1840 = 'B209-5652 temper H32'
1842 = 'B209-5652 temper H34'
1844 = 'B209-5652 temper H112'
1846 = 'B209-5083 temper 0'
1848 = 'B209-5083 temper H321'
1850 = 'B209-5086 temper 0'
1852 = 'B209-5086 temper H32'
1854 = 'B209-5086 temper H34'
1856 = 'B209-5086 temper H112'
1858 = 'B209-5154 temper 0'
1860 = 'B209-5154 temper H32'
1862 = 'B209-5154 temper H34'
1864 = 'B209-5154 temper H112'
1866 = 'B209-5254 temper 0'
1868 = 'B209-5254 temper H32'
1870 = 'B209-5254 temper H34'
1872 = 'B209-5254 temper H112'
1874 = 'B209-5454 temper 0'
1876 = 'B209-5454 temper H32'
1878 = 'B209-5454 temper H34'
1880 = 'B209-5454 temper H112'
1882 = 'B209-5456 temper 0'
1884 = 'B209-5456 temper H321'
1886 = 'B209-6061 temper T4'
1888 = 'B209-6061 temper T4, wld'
604
Codelists
1890
1892
1894
1896
1898
1900
1902
1904
1906
1908
1910
1912
1914
1916
1918
1920
1922
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
'B209-6061 temper
'B209-6061 temper
'B209-6061 temper
'B209-Alclad 3003
'B209-Alclad 3003
'B209-Alclad 3003
'B209-Alclad 3003
'B209-Alclad 3004
'B209-Alclad 3004
'B209-Alclad 3004
'B209-Alclad 3004
'B209-Alclad 6061
'B209-Alclad 6061
'B209-Alclad 6061
'B209-Alclad 6061
'B209-Alclad 6061
'B209-Alclad 6061
T6'
T6, wld'
T651'
temper 0'
temper H12'
temper H14'
temper H112'
temper 0'
temper H32'
temper H34'
temper H112'
temper T4'
temper T4, wld'
temper T6'
temper T6, wld'
temper T451'
temper T651'
605
Codelists
1930
1932
1934
1936
1938
1940
1942
1944
1946
1948
1950
1952
1954
1956
1958
1960
1962
1964
1966
1968
1970
1972
1974
1976
1978
1980
1982
1984
1986
1988
1990
1992
1994
2010
2012
2014
2016
2018
2020
2022
2024
2026
2028
2030
2032
2034
2036
2038
2040
2042
2044
2046
2048
2050
606
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
'B210-1060 temper
'B210-1060 temper
'B210-1060 temper
'B210-3003 temper
'B210-3003 temper
'B210-3003 temper
'B210-3003 temper
'B210-5052 temper
'B210-5052 temper
'B210-5052 temper
'B210-5083 temper
'B210-5083 temper
'B210-5086 temper
'B210-5086 temper
'B210-5086 temper
'B210-5086 temper
'B210-5154 temper
'B210-5154 temper
'B210-5456 temper
'B210-5456 temper
'B210-6061 temper
'B210-6061 temper
'B210-6061 temper
'B210-6061 temper
'B210-6063 temper
'B210-6063 temper
'B210-6063 temper
'B210-6063 temper
'B210-6063 temper
'B210-Alclad 3002
'B210-Alclad 3003
'B210-Alclad 3003
'B210-Alclad 3002
'B221-1060 temper
'B221-1060 temper
'B221-1100 temper
'B221-1100 temper
'B221-3003 temper
'B221-3003 temper
'B221-5052 temper
'B221-5053 temper
'B221-5086 temper
'B221-5154 temper
'B221-5454 temper
'B221-5456 temper
'B221-6061 temper
'B221-6061 temper
'B221-6061 temper
'B221-6061 temper
'B221-6063 temper
'B221-6063 temper
'B221-6063 temper
'B221-6063 temper
'B221-6063 temper
0'
H14'
H112'
0'
H14'
H18'
H112'
0'
H32'
H34'
0'
H112'
0'
H32'
H34'
H112'
0'
H34'
0'
H112'
T4'
T4, wld'
T6'
T6, wld'
T4'
T4, wld'
T5, wld'
T6'
T6, wld'
temper 0'
temper H14'
temper H18'
temper H112'
0'
H112'
0'
H112'
0'
H112'
0'
0'
0'
0'
0'
0'
T4'
T4, wld'
T6'
T6, wld'
T4'
T4, wld'
T5'
T5, wld'
T6'
Codelists
2052
2054
2056
2070
2072
2074
2076
2078
2080
2082
2084
2086
2088
2090
2092
2094
2096
2098
2100
2102
2104
2106
2108
2110
2112
2114
2116
2118
2120
2122
2124
2126
2128
2130
2140
2142
2144
2146
2148
2150
2152
2160
2162
2164
2166
2168
2170
2172
2174
2176
2178
2180
2182
2184
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
'B221-6063 temper
'B221-Alclad 3003
'B221-Alclad 3003
'B241-1060 temper
'B241-1060 temper
'B241-1100 temper
'B241-1100 temper
'B241-3003 temper
'B241-3003 temper
'B241-3003 temper
'B241-5052 temper
'B241-5083 temper
'B241-5083 temper
'B241-5086 temper
'B241-5086 temper
'B241-5454 temper
'B241-5454 temper
'B241-5456 temper
'B241-5456 temper
'B241-5462 temper
'B241-5462 temper
'B241-6061 temper
'B241-6061 temper
'B241-6061 temper
'B241-6061 temper
'B241-6061 temper
'B241-6063 temper
'B241-6063 temper
'B241-6063 temper
'B241-6063 temper
'B241-6063 temper
'B241-6063 temper
'B241-Alclad 3003
'B241-Alclad 3003
'B247-3003 temper
'B247-3003 temper
'B247-5083 temper
'B247-5083 temper
'B247-5083 temper
'B247-6061 temper
'B247-6061 temper
'B345-1060 temper
'B345-1060 temper
'B345-3003 temper
'B345-3003 temper
'B345-3003 temper
'B345-5083 temper
'B345-5083 temper
'B345-5086 temper
'B345-5086 temper
'B345-6061 temper
'B345-6061 temper
'B345-6061 temper
'B345-6061 temper
T6, wld'
temper 0'
temper H112'
0'
H112'
0'
H112'
0'
H18'
H112'
0'
0'
H112'
0'
H112'
0'
H112'
0'
H112'
0'
H112'
T4'
T4, wld'
T6, <NPD 1'
T6, =>NPD 1'
T6, wld'
T4'
T4, wld'
T5'
T5, wld'
T6'
T6, wld'
temper 0'
temper H112'
H112'
H112, wld'
0'
H112'
H112, wld'
T6'
T6, wld'
0'
H112'
0'
H18'
H112'
0'
H112'
0'
H112'
T4'
T4, wld'
T6, <NPD 1'
T6, =>NPD 1'
607
Codelists
2186
2188
2190
2192
2194
2196
2198
2200
2202
2220
2222
2224
2226
2228
2230
2232
2234
2236
2238
2240
2242
2244
2246
2248
2250
2252
2254
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
608
Codelists
Gaskets 3000-3999]
3051 = 'G51'
[Flat, org fib, nitrile binder]
3052 = 'G52'
[Flat, org fib, nitrile binder, full face]
3076 = 'G76'
[Flat, graph]
3077 = 'G77'
[Flat, graph, full face]
3078 = 'G78'
[Flat, graph, 304 tang reinf]
3079 = 'G79'
[Flat, graph, 304 wire mesh reinf]
3101 = 'G101'
[Flat, asb]
3102 = 'G102'
[Flat, asb, full face]
3103 = 'G103'
[Flat, asb, wire mesh reinf]
3111 = 'G111'
[Flat, blue-asb]
3112 = 'G112'
[Flat, blue-asb, full face]
3154 = 'G154'
[Flat, Buna-N]
3171 = 'G171'
[Flat, Hypalon]
3175 = 'G175'
[Flat, Kel-F]
3189 = 'G189'
[Flat, neoprene]
3195 = 'G195'
[Flat, polyethylene]
3204 = 'G204'
[Flat, Teflon]
3210 = 'G210'
[Flat, Viton]
3231 = 'G231'
[Flat, soft-iron]
3234 = 'G234'
[Flat, 304]
3236 = 'G236'
[Flat, 321/347
3241 = 'G241'
[Corr, soft-iron]
3244 = 'G244'
[Corr, 304]
3246 = 'G246'
[Corr, 321/347
3251 = 'G251'
[Flat dbl jktd, PTFE-J, asb-F]
3256 = 'G256'
[Flat dbl jktd, Teflon-J, blue-asb-F]
3261 = 'G261'
[Flat dbl jktd, soft-iron-J, graph-F]
3262 = 'G262'
[Flat dbl jktd, soft-iron-J, asb-F]
3266 = 'G266'
[Flat dbl jktd, low-C-steel-J, graph-F]
3267 = 'G267'
[Flat dbl jktd, low-C-steel-J, asb-F]
3271 = 'G271'
[Flat dbl jktd, 304-J, graph-F]
3272 = 'G272'
[Flat dbl jktd, 304-J, asb-F]
3276 = 'G276'
[Flat dbl jktd, 321/347-J, graph-F]
3277 = 'G277'
[Flat dbl jktd, 321/347-J, asb-F]
3281 = 'G281'
[Flat dbl jktd, I600-J, graph-F]
3282 = 'G282'
[Flat dbl jktd, I600-J, asb-F]
3286 = 'G286'
[Flat dbl jktd, I800-J, graph-F
3306 = 'G306'
[Corr dbl jktd, soft-iron-J, graph-F]
3307 = 'G307'
[Corr dbl jktd, soft-iron-J, asb-F]
3311 = 'G311'
[Corr dbl jktd, low-C-steel-J, graph-F]
3312 = 'G312'
[Corr dbl jktd, low-C-steel-J, asb-F]
3316 = 'G316'
[Corr dbl jktd, 304-J, graph-F]
3317 = 'G317'
[Corr dbl jktd, 304-J, asb-F]
3321 = 'G321'
[Corr dbl jktd, 321/347-J, graph-F]
3322 = 'G322'
[Corr dbl jktd, 321/347-J, asb-F]
3326 = 'G326'
[Corr dbl jktd, I600-J, graph-F]
3327 = 'G327'
[Corr dbl jktd, I600-J, asb-F]
3331 = 'G331'
[Corr dbl jktd, I800-J, graph-F
3356 = 'G356'
[Inlaid corr, soft-iron-J, asb-chords]
3361 = 'G361'
[Inlaid corr, low-C-steel-J, asb-chords]
3366 = 'G366'
[Inlaid corr, 304-J, asb-chords
609
Codelists
3403
3404
3408
3429
3435
3436
3441
3451
3452
3463
3466
3468
3473
3476
3477
3488
3491
3493
3498
3551
3552
3556
3563
3566
3568
3569
3573
3601
3602
3606
3608
3610
3613
3616
3618
3619
3623
3651
3653
3655
3657
3659
3661
3663
3665
3669
610
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
'G403'
'G404'
'G408'
'G429'
'G435'
'G436'
'G441'
'G451'
'G452'
'G463'
'G466'
'G468'
'G473'
'G476'
'G477'
'G488'
'G491'
'G493'
'G498'
'G551'
'G552'
'G556'
'G563'
'G566'
'G568'
'G569'
'G573'
'G601'
'G602'
'G606'
'G608'
'G610'
'G613'
'G616'
'G618'
'G619'
'G623'
'G651'
'G653'
'G655'
'G657'
'G659'
'G661'
'G663'
'G665'
'G669'
[O ring, Buna-N]
[O ring, butyl]
[O ring, EDPM]
[O ring, nitrile]
[O ring, Saran]
[O ring, synthetic rubber]
[O ring, Viton
[BX ring, soft-iron, 90 BHN max]
[BX ring, lo-C, 120 BHN max]
[BX ring, 304, 140 BHN max]
[BX ring, 316, 140 BHN max]
[BX ring, 321, 140 BHN max]
[BX ring, I-X-750
[RX ring, soft-iron, 90 BHN max]
[RX ring, lo-C, 120 BHN max]
[RX ring, 304, 140 BHN max]
[RX ring, 316, 140 BHN max]
[RX ring, 321, 140 BHN max]
[RX ring, I-X-750
[Octag ring, soft-iron, 90 BHN max]
[Octag ring, lo-C, 120 BHN max]
[Octag ring, 5Cr-0.5Mo, 130 BHN max]
[Octag ring, 304, 140 BHN max]
[Octag ring, 316, 140 BHN max]
[Octag ring, 321, 140 BHN max]
[Octag ring, 347, 140 BHN max]
[Octag ring, I-X-750
[Oval ring, soft-iron, 90 BHN max]
[Oval ring, lo-C, 120 BHN max]
[Oval ring, 5Cr-0.5Mo, 130 BHN max]
[Oval ring, 9Cr-1Mo, 130 BHN max]
[Oval ring, 410, 170 BHN max]
[Oval ring, 304, 140 BHN max]
[Oval ring, 316, 140 BHN max]
[Oval ring, 321, 140 BHN max]
[Oval ring, 347, 140 BHN max]
[Oval ring, I-X-750
[Sprl-wnd, 304-W, mica/graph-F, CS-CR]
[Sprl-wnd, 304-W, graph-F, CS-CR]
[Sprl-wnd, 304-W, asb-F, CS-CR]
[Sprl-wnd, 304-W, blue-asb-F, CS-CR]
[Sprl-wnd, 304-W, Teflon-F, CS-CR]
[Sprl-wnd, 304-W, mica/graph-F, CS-CR, 304-IR]
[Sprl-wnd, 304-W, graph-F, CS-CR, 304-IR]
[Sprl-wnd, 304-W, asb-F, CS-CR, 304-IR]
[Sprl-wnd, 304-W, Teflon-F, CS-CR, 304-IR
Codelists
3671
3673
3675
3677
3679
3681
3683
3685
3689
3691
3693
3695
3699
3701
3703
3705
3709
3711
3713
3715
3719
3721
3723
3725
3729
3731
3733
3735
3739
3741
3743
3745
3749
3751
3753
3755
3761
3763
3765
3771
3773
3775
3781
3783
3785
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
'G671'
'G673'
'G675'
'G677'
'G679'
'G681'
'G683'
'G685'
'G689'
'G691'
'G693'
'G695'
'G699'
'G701'
'G703'
'G705'
'G709'
'G711'
'G713'
'G715'
'G719'
'G721'
'G723'
'G725'
'G729'
'G731'
'G733'
'G735'
'G739'
'G741'
'G743'
'G745'
'G749'
'G751'
'G753'
'G755'
'G761'
'G763'
'G765'
'G771'
'G773'
'G775'
'G781'
'G783'
'G785'
[Sprl-wnd,
[Sprl-wnd,
[Sprl-wnd,
[Sprl-wnd,
[Sprl-wnd,
[Sprl-wnd,
[Sprl-wnd,
[Sprl-wnd,
[Sprl-wnd,
[Sprl-wnd,
[Sprl-wnd,
[Sprl-wnd,
[Sprl-wnd,
[Sprl-wnd,
[Sprl-wnd,
[Sprl-wnd,
[Sprl-wnd,
[Sprl-wnd,
[Sprl-wnd,
[Sprl-wnd,
[Sprl-wnd,
[Sprl-wnd,
[Sprl-wnd,
[Sprl-wnd,
[Sprl-wnd,
[Sprl-wnd,
[Sprl-wnd,
[Sprl-wnd,
[Sprl-wnd,
[Sprl-wnd,
[Sprl-wnd,
[Sprl-wnd,
[Sprl-wnd,
[Sprl-wnd,
[Sprl-wnd,
[Sprl-wnd,
[Sprl-wnd,
[Sprl-wnd,
[Sprl-wnd,
[Sprl-wnd,
[Sprl-wnd,
[Sprl-wnd,
[Sprl-wnd,
[Sprl-wnd,
[Sprl-wnd,
611
Codelists
Bolting 4000-4999]
4011 = 'B11'
[A193-B5, >=1.5" lub, w/A194-3]
4012 = 'B12'
[A193-B5, lub, w/A194-3]
4014 = 'B14'
[A193-B5, >=1.5" lub, w/A194-4]
4015 = 'B15'
[A193-B5, lub, w/A194-4]
4021 = 'B21'
[A193-B6, >=1.5" lub, w/A194-6]
4022 = 'B22'
[A193-B6, lub, w/A194-6]
4031 = 'B31'
[A193-B7, >=1.5" lub, w/A194-2H]
4032 = 'B32'
[A193-B7, lub, w/A194-2H]
4033 = 'B33'
[A193-B7 zinc coated w/A194-2H zinc coated]
4035 = 'B35'
[A193-B7 galv w/A194-2H galv]
4038 = 'B38'
[A193-B7M, >=1.5" lub, w/A194-2H]
4039 = 'B39'
[A193-B7M, lub, w/A194-2H]
4041 = 'B41'
[A193-B8 Cl.1, >=1.5" lub, w/A194-8]
4042 = 'B42'
[A193-B8 Cl.1, lub, w/A194-8]
4044 = 'B44'
[A193-B8C Cl.1, >=1.5" lub, w/A194-8C]
4045 = 'B45'
[A193-B8C Cl.1, lub, w/A194-8C]
4046 = 'B46'
[A193-B8 Cl.1, lub, w/A194-8]
4047 = 'B47'
[A193-B8M Cl.1, >=1.5" lub, w/A194-8M]
4048 = 'B48'
[A193-B8M Cl.1, lub, w/A194-8M
4050 = 'B50'
[A193-B8T Cl.1, >=1.5" lub, w/A194-8T]
4051 = 'B51'
[A193-B8T Cl.1, lub, w/A194-8T]
4061 = 'B61'
[A193-B16, >=1.5" lub, w/A194-3]
4062 = 'B62'
[A193-B16, lub, w/A194-3]
4064 = 'B64'
[A193-B16, >=1.5" lub, w/A194-4]
4065 = 'B65'
[A193-B16, lub, w/A194-4]
4066 = 'B66'
[A193-B16, >=1.5" lub, w/A194-7]
4067 = 'B67'
[A193-B16, lub, w/A194-7]
4068 = 'B68'
[A193-B16, >=1.5" lub, w/A194-8M]
4069 = 'B69'
[A193-B16, lub, w/A194-8M]
4071 = 'B71'
[A307-B w/A563-A]
4074 = 'B74'
[A320-L7, >=1.5" lub, w/A194-4]
4075 = 'B75'
[A320-L7, lub, w/A194-4]
4076 = 'B76'
[A320-B8, >=1.5" lub, w/A194-8]
4077 = 'B77'
[A320-B8, lub, w/A194-8]
4078 = 'B78'
[A320-B8, >=1.5" lub, w/A194-B8]
4079 = 'B79'
[A320-B8, lub, w/A194-B8]
4080 = 'B80'
[A320-B8T Cl.1 >=1.5" lub, w/A194-B8]
4081 = 'B81'
[A320-B8T Cl.1 lub, w/A194-B8]
4082 = 'B82'
[A325 w/A325]
4084 = 'B84'
[A453-660, >=1.5" lub, w/A453-660]
4085 = 'B85'
[A453-660, lub, w/A453-660
4500 = 'Undefined'
Materials for British Standards - Ranges used 6000-7999
612
Codelists
carbon steel pipes and tubes BS3601
6000 = 'BS3601:BW320'
6001 = 'BS3601:ERW320'
6002 = 'BS3601:ERW360'
6003 = 'BS3601:ERW430'
6004 = 'BS3601:S360'
6005 = 'BS3601:S430'
6006 = 'BS3601:SAW430'
steel pipes
6010 =
6011 =
6012 =
6013 =
6014 =
6015 =
6016 =
6017 =
6018 =
6019 =
6020 =
6021 =
6022 =
6023 =
6024 =
6025 =
6026 =
6027 =
6028 =
6029 =
steel pipes
6030 =
6031 =
6032 =
6033 =
steel pipes
6040 =
6041 =
6042 =
6043 =
6044 =
6045 =
6046 =
6047 =
6048 =
6049 =
6050 =
6051 =
6052 =
6053 =
6054 =
6055 =
613
Codelists
steel pipes
6060 =
6061 =
6062 =
6063 =
6064 =
6065 =
6066 =
6067 =
6068 =
6069 =
6070 =
6071 =
6072 =
6073 =
6074 =
6075 =
6076 =
6077 =
6078 =
6079 =
6080 =
6081 =
6082 =
6083 =
6084 =
6085 =
6086 =
6087 =
6088 =
6089 =
6090 =
6091 =
6092 =
6093 =
6094 =
6095 =
6096 =
6097 =
6098 =
6099 =
6100 =
6101 =
6102 =
6103 =
6104 =
6105 =
6106 =
6107 =
614
Codelists
SS pipes and tubes for pressure purposes BS3605:1973
6110 = 'BS3605 304S14'
6111 = 'BS3605 304S18'
6112 = 'BS3605 304S59'
6113 = 'BS3605 304S22'
6114 = 'BS3605 304S25'
6115 = 'BS3605 316S14'
6116 = 'BS3605 316S18'
6117 = 'BS3605 316S59'
6118 = 'BS3605 316S22'
6119 = 'BS3605 316S26'
6120 = 'BS3605 321S18'
6121 = 'BS3605 321S59(1010)'
6122 = 'BS3605 321S59(1105)'
6123 = 'BS3605 321S22'
6124 = 'BS3605 347S18'
6125 = 'BS3605 347S59'
6126 = 'BS3605 347S17'
615
Codelists
plates BS1501 part 1 1980
6200 = 'BS1501-141 360A'
6201 = 'BS1501-151 360A'
6202 = 'BS1501-151 400A'
6203 = 'BS1501-151 430A'
6204 = 'BS1501-151 360B'
6205 = 'BS1501-151 400B'
6206 = 'BS1501-151 430B'
6207 = 'BS1501-154 360A'
6208 = 'BS1501-154 400A'
6209 = 'BS1501-154 430A'
6210 = 'BS1501-161 360A'
6211 = 'BS1501-161 400A'
6212 = 'BS1501-161 430A'
6213 = 'BS1501-161 360B'
6214 = 'BS1501-161 400B'
6215 = 'BS1501-161 430B'
6216 = 'BS1501-164 360A RT'
6217 = 'BS1501-164 360A LT0'
6218 = 'BS1501-164 360A LT20'
6219 = 'BS1501-164 360B RT'
6220 = 'BS1501-164 360B LT0'
6221 = 'BS1501-164 360B LT20'
6222 = 'BS1501-164 400A RT'
6223 = 'BS1501-164 400A LT0'
6224 = 'BS1501-164 400A LT20'
6225 = 'BS1501-164 400B RT'
6226 = 'BS1501-164 400B LT0'
6227 = 'BS1501-164 400B LT20'
6228 = 'BS1501-223 460A RT'
6229 = 'BS1501-223 460A LT0'
6230 = 'BS1501-223 460A LT15'
6231 = 'BS1501-223 460A LT30'
6232 = 'BS1501-223 460B RT'
6233 = 'BS1501-223 460B LT0'
6234 = 'BS1501-223 460B LT15'
6235 = 'BS1501-223 460B LT30'
6236 = 'BS1501-223 490A RT'
6237 = 'BS1501-223 490A LT0'
6238 = 'BS1501-223 490A LT15'
6239 = 'BS1501-223 490A LT30'
6240 = 'BS1501-223 490B RT'
6241 = 'BS1501-223 490B LT0'
6242 = 'BS1501-223 490B LT15'
6243 = 'BS1501-223 490B LT30'
6244 = 'BS1501-224 400A RT'
6245 = 'BS1501-224 400A LT0'
6246 = 'BS1501-224 400A LT20'
6247 = 'BS1501-224 400A LT30'
6248 = 'BS1501-224 400A LT40'
6249 = 'BS1501-224 400A LT50'
6250 = 'BS1501-224 400B RT'
6251 = 'BS1501-224 400B LT0'
6252 = 'BS1501-224 400B LT20'
616
Codelists
6253
6254
6255
6256
6257
6258
6259
6260
6261
6262
6263
6264
6265
6266
6267
6268
6269
6270
6271
6272
6273
6274
6275
6276
6277
6278
6279
6280
6281
6282
6283
6284
6285
6286
6287
6288
6289
6290
6291
6292
6293
6294
6295
6296
6297
6298
6299
6300
6301
6302
6303
6304
6305
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
'BS1501-224
'BS1501-224
'BS1501-224
'BS1501-224
'BS1501-224
'BS1501-224
'BS1501-224
'BS1501-224
'BS1501-224
'BS1501-224
'BS1501-224
'BS1501-224
'BS1501-224
'BS1501-224
'BS1501-224
'BS1501-224
'BS1501-224
'BS1501-224
'BS1501-224
'BS1501-224
'BS1501-224
'BS1501-224
'BS1501-224
'BS1501-224
'BS1501-224
'BS1501-224
'BS1501-224
'BS1501-224
'BS1501-224
'BS1501-224
'BS1501-224
'BS1501-224
'BS1501-224
'BS1501-224
'BS1501-224
'BS1501-224
'BS1501-224
'BS1501-224
'BS1501-224
'BS1501-225
'BS1501-225
'BS1501-225
'BS1501-225
'BS1501-225
'BS1501-225
'BS1501-225
'BS1501-225
'BS1501-225
'BS1501-225
'BS1501-225
'BS1501-225
'BS1501-225
'BS1501-225
400B
400B
400B
430A
430A
430A
430A
430A
430A
430B
430B
430B
430B
430B
430B
460A
460A
460A
460A
460A
460A
460B
460B
460B
460B
460B
460B
490A
490A
490A
490A
490A
490A
490B
490B
490B
490B
490B
490B
460A
460A
460A
460A
460B
460B
460B
460B
490A
490A
490A
490B
490B
490B
LT30'
LT40'
LT50'
RT'
LT0'
LT20'
LT30'
LT40'
LT50'
RT'
LT0'
LT20'
LT30'
LT40'
LT50'
RT'
LT0'
LT20'
LT30'
LT40'
LT50'
RT'
LT0'
LT20'
LT30'
LT40'
LT50'
RT'
LT0'
LT20'
LT30'
LT40'
LT50'
RT'
LT0'
LT20'
LT30'
LT40'
LT50'
LT20'
LT30'
LT50'
LT60'
LT20'
LT30'
LT50'
LT60'
LT20'
LT30'
LT50'
LT20'
LT30'
LT50'
617
Codelists
steel plates BS1501 part 2 1988
6310 = 'BS1501-243'
6311 = 'BS1501-271'
6312 = 'BS1501-281'
6313 = 'BS1501-620'
6314 = 'BS1501-621'
6315 = 'BS1501-622-515'
6316 = 'BS1501-622-690'
6317 = 'BS1501-660'
6318 = 'BS1501-503'
6319 = 'BS1501-510'
6320 = 'BS1501-828'
618
Codelists
steel plates BS1501 part 3 1973
6321 = 'BS1501-403S17A'
6322 = 'BS1501-405S17A'
6323 = 'BS1501-304S12A'
6324 = 'BS1501-304S15A'
6325 = 'BS1501-304S49A'
6326 = 'BS1501-321S12A'
6327 = 'BS1501-321S49A'
6328 = 'BS1501-347S17A'
6329 = 'BS1501-347S49A'
6330 = 'BS1501-316S12A'
6331 = 'BS1501-316S16A'
6332 = 'BS1501-316S37A'
6333 = 'BS1501-316S49A'
6334 = 'BS1501-320S17A'
6335 = 'BS1501-310S24A'
6336 = 'BS1501-NA15A'
6337 = 'BS1501-NA16A'
6338 = 'BS1501-460S52A'
6339 = 'BS1501-304S62A'
6340 = 'BS1501-304S65A'
6341 = 'BS1501-304S87A'
6342 = 'BS1501-347S67A'
6343 = 'BS1501-316S62A'
6344 = 'BS1501-316S66A'
6345 = 'BS1501-316S82A'
6351 = 'BS1501-403S17B'
6352 = 'BS1501-405S17B'
6353 = 'BS1501-304S12B'
6354 = 'BS1501-304S15B'
6355 = 'BS1501-304S49B'
6356 = 'BS1501-351S12B'
6357 = 'BS1501-351S49B'
6358 = 'BS1501-347S17B'
6359 = 'BS1501-347S49B'
6360 = 'BS1501-316S12B'
6361 = 'BS1501-316S16B'
6362 = 'BS1501-316S37B'
6363 = 'BS1501-316S49B'
6364 = 'BS1501-320S17B'
6365 = 'BS1501-310S24B'
6366 = 'BS1501-NA15B'
6367 = 'BS1501-NA16B'
6368 = 'BS1501-460S52B'
6369 = 'BS1501-304S62B'
6370 = 'BS1501-304S65B'
6371 = 'BS1501-304S87B'
6372 = 'BS1501-377S67B'
6373 = 'BS1501-316S62B'
6374 = 'BS1501-316S66B'
6375 = 'BS1501-316S82B'
6376 = 'BS1501-460S52A LT70'
619
Codelists
steel forgings to BS1503 1980
6380 = 'BS1503 164-490'
6381 = 'BS1503 221-410'
6382 = 'BS1503 221-430'
6383 = 'BS1503 221-460'
6384 = 'BS1503 221-490'
6385 = 'BS1503 221-510'
6386 = 'BS1503 221-530'
6387 = 'BS1503 221-550'
6388 = 'BS1503 223-410'
6389 = 'BS1503 223-430'
6390 = 'BS1503 223-460'
6391 = 'BS1503 223-490'
6392 = 'BS1503 223-510'
6393 = 'BS1503 224-410'
6394 = 'BS1503 224-430'
6395 = 'BS1503 224-460'
6396 = 'BS1503 224-490'
6397 = 'BS1503 224-510'
6398 = 'BS1503 245-420'
6399 = 'BS1503 620-440'
6400 = 'BS1503 620-540'
6401 = 'BS1503 621-460'
6402 = 'BS1503 660-460'
6403 = 'BS1503 271-560'
6404 = 'BS1503 622-490'
6405 = 'BS1503 622-560'
6406 = 'BS1503 622-650'
6407 = 'BS1503 625-520'
6408 = 'BS1503 625-590'
6409 = 'BS1503 503-490'
6410 = 'BS1503 509-690'
6411 = 'BS1503 410S21'
6412 = 'BS1503 420S29'
6413 = 'BS1503 403S17'
6414 = 'BS1503 405S17'
6415 = 'BS1503 304S11'
6416 = 'BS1503 304S31'
6417 = 'BS1503 304S51'
6418 = 'BS1503 347S31'
6419 = 'BS1503 347S51'
6420 = 'BS1503 321S31'
6421 = 'BS1503 321S51-490'
6422 = 'BS1503 321S51-510'
6423 = 'BS1503 316S11'
6424 = 'BS1503 316S13'
6425 = 'BS1503 316S31'
6426 = 'BS1503 316S33'
6427 = 'BS1503 316S51'
6428 = 'BS1503 320S33'
6429 = 'BS1503 310S31'
620
Codelists
6430
6431
6432
6433
6434
6435
6436
6437
6438
6439
6440
6441
6442
6443
6444
6445
6446
6447
6448
6449
6450
6451
6452
6453
6454
6455
6456
6457
6458
6459
6460
6461
6462
6463
6464
6465
6466
6467
6468
6469
6470
6471
6472
6473
6474
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
164-490E'
221-430E'
221-460E'
221-490E'
221-510E'
221-530E'
221-550E'
223-410E'
223-430E'
223-460E'
223-490E'
223-510E'
224-410E'
224-430E'
224-460E'
224-490E'
224-510E'
245-420E'
620-440E'
620-540E'
621-460E'
660-460E'
271-560E'
622-490E'
622-560E'
622-650E'
625-520E'
625-590E'
410S21E'
420S29E'
403S17E'
405S17E'
304S11E'
304S31E'
304S51E'
347S31E'
347S51E'
321S31E'
321S51-490E'
321S51-510E'
316S11E'
316S13E'
316S31E'
316S33E'
316S51E'
621
Codelists
6475
6476
6477
6478
6479
6480
6481
6482
6483
6484
6485
6486
6487
6488
6489
6490
6491
6492
6493
6494
6495
6496
6497
6498
6499
6500
6501
6502
6503
6504
6505
6506
6507
6508
6509
6510
622
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
'BS1503
223-410-LT10'
223-410-LT20'
223-410-LT50'
223-430-LT10'
223-430-LT15'
223-430-LT40'
223-460-LT0'
223-460-LT10'
223-460-LT20'
223-490-LT0'
223-490-LT10'
223-510-LT0'
224-410-LT10'
224-410-LT20'
224-410-LT50'
224-430-LT10'
224-430-LT15'
224-430-LT40'
224-460-LT0'
224-460-LT10'
224-460-LT20'
224-490-LT0'
224-490-LT10'
224-510-LT0'
503-490-LT80'
509-690-LT196'
304S11-LT196'
304S31-LT196'
347S31-LT196'
321S31-LT196'
321S51-490'
321S51-510'
316S11-LT196'
316S13-LT196'
316S31-LT196'
316S33-LT196'
Codelists
steel casting to BS1504 1976
6520 = 'BS1504-161 grade 430A'
6521 = 'BS1504-161 grade 480A'
6522 = 'BS1504-161 grade 540A'
6523 = 'BS1504-161 grade 430E'
6524 = 'BS1504-161 grade 480E'
6525 = 'BS1504-161 grade 430A-LT40'
6526 = 'BS1504-245A'
6527 = 'BS1504-245B'
6528 = 'BS1504-245A-LT50'
6529 = 'BS1504-503-LT60'
6530 = 'BS1504-621A'
6531 = 'BS1504-622A'
6532 = 'BS1504-622E'
6533 = 'BS1504-623A'
6534 = 'BS1504-625A'
6535 = 'BS1504-625E'
6536 = 'BS1504-629A'
6537 = 'BS1504-660A'
6538 = 'BS1504-420C29A'
6539 = 'BS1504-425C11A'
6540 = 'BS1504-304C15A'
6541 = 'BS1504-304C15A-LT196'
6542 = 'BS1504-304C12A'
6543 = 'BS1504-304C12A-LT196'
6544 = 'BS1504-347C17A'
6545 = 'BS1504-347C17A-LT196'
6546 = 'BS1504-315C16A'
6547 = 'BS1504-315C16A-LT196'
6548 = 'BS1504-316C12A'
6549 = 'BS1504-316C16A'
6550 = 'BS1504-316C71A'
6551 = 'BS1504-318C17A'
6552 = 'BS1504-316C16E'
6553 = 'BS1504-316C71E'
6554 = 'BS1504-316C12A-LT196'
6555 = 'BS1504-316C16A-LT196'
6556 = 'BS1504-316C71A-LT196'
6557 = 'BS1504-317C12A'
6558 = 'BS1504-317C16A'
6559 = 'BS1504-364C11A'
6560 = 'BS1504-332C11A'
6561 = 'BS1504-310C40A'
6562 = 'BS1504-330C11A'
623
Codelists
steel bars and billets for bolting BS1506 1986
6570 = 'BS1506-162'
6571 = 'BS1506-253'
6572 = 'BS1506-253-LT100'
6573 = 'BS1506-509-650'
6574 = 'BS1506-509-650-LT196'
6575 = 'BS1506-509-690'
6576 = 'BS1506-509-690-LT196'
6577 = 'BS1506-630-790'
6578 = 'BS1506-630-790-LT100'
6579 = 'BS1506-630-790-LT75'
6580 = 'BS1506-630-860'
6581 = 'BS1506-630-860-LT100'
6582 = 'BS1506-630-690'
6583 = 'BS1506-630-690-LT100'
6584 = 'BS1506-631-850'
6585 = 'BS1506-670-860'
6586 = 'BS1506-671-850'
6587 = 'BS1506-681-820'
6588 = 'BS1506-410S21-690'
6589 = 'BS1506-410S21-720'
6590 = 'BS1506-410S21-760'
6591 = 'BS1506-410S21-750'
6592 = 'BS1506-410S21-770'
6593 = 'BS1506-416S29'
6594 = 'BS1506-286S31'
6595 = 'BS1506-286S31-LT196'
6596 = 'BS1506-304S31'
6597 = 'BS1506-304S31-LT196'
6598 = 'BS1506-304S51'
6599 = 'BS1506-304S61'
6600 = 'BS1506-304S61-LT196'
6601 = 'BS1506-304S71'
6602 = 'BS1506-304S71-LT196'
6603 = 'BS1506-303S22'
6604 = 'BS1506-316S31'
6605 = 'BS1506-316S31-LT196'
6606 = 'BS1506-316S33'
6607 = 'BS1506-316S33-LT196'
6608 = 'BS1506-316S51'
6609 = 'BS1506-316S53'
6610 = 'BS1506-316S61'
6611 = 'BS1506-316S61-LT196'
6612 = 'BS1506-316S63'
6613 = 'BS1506-316S63-LT196'
6614 = 'BS1506-316S65'
6615 = 'BS1506-316S65-LT196'
6616 = 'BS1506-316S67'
6617 = 'BS1506-316S67-LT196'
6618 = 'BS1506-321S31'
6619 = 'BS1506-321S31-LT196'
6620 = 'BS1506-321S51-490'
6621 = 'BS1506-321S51-520'
6622 = 'BS1506-347S31'
624
Codelists
6623 = 'BS1506-347S31-LT196'
6624 = 'BS1506-347S51'
7999 = 'undefined'
F
[FAY1W8] [8F0002] 'Gravity Head, Gray CI'
[FDYLW8] [8F0003] 'Gravity Head, DI Cement Lined'
[FDYLU9] [9F0006] 'AWWA 150# MJ, DI Cement Lined'
625
Codelists
Carbon
14 =
16 =
19 =
31 =
32 =
33 =
35 =
43 =
45 =
48 =
49 =
50 =
51 =
65 =
66 =
73 =
74 =
75 =
76 =
105 =
106 =
146 =
153 =
171 =
176 =
177 =
182 =
183 =
185 =
186 =
320 =
389 =
390 =
391 =
394 =
395 =
396 =
397 =
400 =
401 =
402 =
403 =
405 =
407 =
458 =
459 =
460 =
461 =
548 =
549 =
551 =
557 =
564 =
626
Steels, C
[CAA5UA] [AC0014]
[CAA5VA] [AC0016]
[CAALV1] [1C0019]
[CAC5C1] [1C0031]
[CAC5C2] [2C0032]
[CAC5C4] [4C0033]
[CAC5G1] [1C0035]
[CAC5Q1] [1C0043]
[CAC5R1] [1C0045]
[CAC5U1] [1C0048]
[CAC7C1] [1C0049]
[CAC7C2] [2C0050]
[CAC7C4] [4C0051]
[CAC8C1] [1C0065]
[CAC8C2] [2C0066]
[CAC9C1] [1C0073]
[CAC9C2] [2C0074]
[CAC9C4] [4C0075]
[CAC9C5] [5C0076]
[CAD7K1] [1C0105]
[CAD7K2] [2C0106]
[CAF5S1] [1C0146]
[CAF7J1] [1C0153]
[CAFYC1] [1C0171]
[CAH5C1] [1C0176]
[CAH5C2] [2C0177]
[CAH5G1] [1C0182]
[CAH5G2] [2C0183]
[CAH7C1] [1C0185]
[CAH7C2] [2C0186]
[CALYC2] [2C0320]
[CAU5P4] [4C0389]
[CAU5P5] [5C0390]
[CAU5P6] [6C0391]
[CAU5Q2] [2C0394]
[CAU5Q4] [4C0395]
[CAU5Q5] [5C0396]
[CAU5Q6] [6C0397]
[CAU5R2] [2C0400]
[CAU5R4] [4C0401]
[CAU5R5] [5C0402]
[CAU5R6] [6C0403]
[CAU5RF] [FC0405]
[CAU7C6] [6C0407]
[CAYYC1] [1C0458]
[CAYYC2] [2C0459]
[CDA1U1] [1C0460]
[CDA5U1] [1C0461]
[CJD7K1] [1C0548]
[CJD7K2] [2C0549]
[CJD7K5] [5C0551]
[CJD8K2] [2C0557]
[CJD9K1] [1C0564]
Codelists
577
593
600
601
602
609
610
611
618
619
620
630
722
723
724
730
731
732
785
794
800
803
841
842
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
[CJE7C2]
[CJE9C2]
[CJF5C1]
[CJF5C2]
[CJF5C4]
[CJF7C1]
[CJF7C2]
[CJF7C4]
[CJF9C1]
[CJF9C2]
[CJF9C4]
[CJH7C4]
[CJL7C2]
[CJL7C4]
[CJL7C5]
[CJL9C2]
[CJL9C4]
[CJL9C5]
[CJU7C6]
[CJV5C6]
[CJV7C6]
[CJV7K6]
[CPD5D1]
[CPD5D2]
[2C0577]
[2C0593]
[1C0600]
[2C0601]
[4C0602]
[1C0609]
[2C0610]
[4C0611]
[1C0618]
[2C0619]
[4C0620]
[4C0630]
[2C0722]
[4C0723]
[5C0724]
[2C0730]
[4C0731]
[5C0732]
[6C0785]
[6C0794]
[6C0800]
[6C0803]
[1C0841]
[2C0842]
627
Codelists
Low and Intermediate Alloy Steels, L
1669 = [LPFYG2] [2L1669] 'CL300 RFFE, 1.25Cr-0.5Mo, 316 Trim'
1670 = [LPTYG2] [2L1670] 'CL300 RFFE, 1.25Cr-0.5Mo, 316 Trim'
1671 = [LPH5B1] [1L1671] 'CL150 RFFE-SF, 1.25Cr-0.5Mo, Trim 8'
1672 = [LPH5B2] [2L1672] 'CL300 RFFE-SF, 1.25Cr-0.5Mo, Trim 8'
1673 = [LPH5B4] [4L1673] 'CL600 RFFE-SF, 1.25Cr-0.5Mo, Trim 8'
1677 = [LPH7B1] [1L1677] 'CL150 RFFE-SF, 1.25Cr-0.5Mo, Trim 8'
1678 = [LPH7B2] [2L1678] 'CL300 RFFE-SF, 1.25Cr-0.5Mo, Trim 8'
1679 = [LPH7B4] [4L1679] 'CL600 RFFE-SF, 1.25Cr-0.5Mo, Trim 8'
1691 = [LPH9B4] [4L1691] 'CL600 RFFE-SF, 1.25Cr-0.5Mo, Trim 8'
1864 = [LPU5B6] [6L1864] 'CL1500 BE/RJFE, 1.25Cr-0.5Mo, Trim 8'
1868 = [LPU5P5] [5L1868] 'CL900 BE/RFFE, 1.25Cr-0.5Mo, Trim 5,
(ASME-I)'
1869 = [LPU5P6] [6L1869] 'CL1500 BE/RJFE, 1.25Cr-0.5Mo, Trim 5,
(ASME-I)'
1874 = [LPU5Q5] [5L1874] 'CL900 BE/RFFE, 1.25Cr-0.5Mo, Trim 5,
(ANSI-B31.1)'
1875 = [LPU5Q6] [6L1875] 'CL1500 BE/RJFE, 1.25Cr-0.5Mo, Trim 5,
(ANSI-B31.1)'
1882 = [LPU5R6] [6L1882] 'CL1500 BE/RJFE, 1.25Cr-0.5Mo, Trim 5,
(ANSI-B31.3)'
1885 = [LPU7B6] [6L1885] 'CL1500 BE/RJFE, 1.25Cr-0.5Mo, Trim 8'
3013 = [LTC5B1] [1L3013] 'CL150 RFFE, 5Cr-0.5Mo, Trim 8'
3014 = [LTC5B2] [2L3014] 'CL300 RFFE, 5Cr-0.5Mo, Trim 8'
3027 = [LTC7B1] [1L3027] 'CL150 RFFE, 5Cr-0.5Mo, Trim 8'
3028 = [LTC7B2] [2L3028] 'CL300 RFFE, 5Cr-0.5Mo, Trim 8'
3029 = [LTC7B4] [4L3029] 'CL600 RFFE, 5Cr-0.5Mo, Trim 8'
3040 = [LTC8B1] [1L3040] 'CL150 RFFE, 5Cr-0.5Mo, Trim 8'
3041 = [LTC8B2] [2L3041] 'CL300 RFFE, 5Cr-0.5Mo, Trim 8'
3042 = [LTC8B4] [4L3042] 'CL600 RFFE, 5Cr-0.5Mo, Trim 8'
3048 = [LTC9B1] [1L3048] 'CL150 RFFE, 5Cr-0.5Mo, Trim 8'
3049 = [LTC9B2] [2L3049] 'CL300 RFFE, 5Cr-0.5Mo, Trim 8'
3193 = [LTH7B5] [5L3193] 'CL900 RFFE-SF, 5Cr-0.5Mo, Trim 8'
3203 = [LTH9B2] [2L3203] 'CL300 RFFE-SF, 5Cr-0.5Mo, NACE, Trim 8'
3204 = [LTH9B4] [4L3204] 'CL600 RFFE-SF, 5Cr-0.5Mo, NACE, Trim 8'
3390 = [LTU7B6] [6L3390] 'CL1500 BE/RJFE, 5Cr-0.5Mo, Trim 8'
3725 = [LVC7B1] [1L3725] 'CL150 RFFE, 9Cr-1Mo, Trim 8'
3726 = [LVC7B2] [2L3726] 'CL300 RFFE, 9Cr-1Mo, Trim 8'
3746 = [LVC9B1] [1L3746] 'CL150 RFFE, 9Cr-1Mo, Trim 8'
3747 = [LVC9B2] [2L3747] 'CL300 RFFE, 9Cr-1Mo, Trim 8'
3748 = [LVC9B4] [4L3748] 'CL600 RFFE, 9Cr-1Mo, Trim 8'
3749 = [LVC9B5] [5L3749] 'CL900 RFFE, 9Cr-1Mo, Trim 8'
628
Codelists
Stainless Steels, S
3977 = [SAC3T1] [1S3977] 'CL150 RFFE, 304/CS Valves, Trim 8'
3978 = [SAC3T2] [2S3978] 'CL300 RFFE, 304/CS Valves, Trim 8'
3979 = [SAC3T4] [4S3979] 'CL600 RFFE, 304/CS Valves, Trim 8'
3980 = [SAC3T5] [5S3980] 'CL900 RFFE, 304/CS Valves, Trim 8'
3984 = [SAD3C1] [1S3984] 'CL150 RFFE, 304/316 Valves, Trim 12'
3985 = [SAD3C2] [2S3985] 'CL300 RFFE, 304/316 Valves, Trim 12'
3988 = [SAD3E1] [1S3988] 'CL150 RFFE, 304, Trim 2'
3989 = [SAD3E2] [2S3989] 'CL300 RFFE, 304, Trim 2'
3991 = [SAD3F1] [1S3991] 'CL150 RFFE, 304, Trim 2'
4104 = [SAFYG1] [1S4104] 'CL150 RFFE, 304, 316 Trim'
4218 = [SAM3T6] [6S4218] 'CL1500 RJFE, 304/CS Valves, Trim 8'
4396 = [SBD3C2] [2S4396] 'CL300 RFFE, 304L/316 Valves, Trim 12'
4488 = [SBF3U1] [1S4488] 'CL150 RFFE, 304/316 Valves, Trim 2'
5135 = [SED5C1] [1S5135] 'CL150 RFFE, 316, Trim 12'
5187 = [SEF3C1] [1S5187] 'CL150 RFFE, 316, Trim 12'
5188 = [SEF3C2] [2S5188] 'CL300 RFFE, 316, Trim 12'
5189 = [SEF3C4] [4S5189] 'CL600 RFFE, 316, Trim 12'
5197 = [SEF3G1] [1S5197] 'CL150 RFFE, 316, Trim 12'
6246 = [SHJ3B2] [2S6246] 'CL300 RFFE-SF, 321/347 Valves, 347HF Trim'
6247 = [SHJ3B4] [4S6247] 'CL600 RFFE-SF, 321/347 Valves, 347HF Trim'
6258 = [SHJ5B2] [2S6258] 'CL300 RFFE-SF, 321/347 Valves, 347HF Trim'
6449 = [SHV3B5] [5S6449] 'CL900 BE/RFFE-SF, 321/347 Valves, 347HF
Trim'
6450 = [SHV3B6] [6S6450] 'CL1500 BE/RJFE, 321/347 Valves, 347HF Trim'
6457 = [SHV5B6] [6S6457] 'CL1500 BE/RJFE, 321/347 Valves, 347HF Trim'
Copper Alloys, K
Nickel Alloys, N
7540 = [NGF5G1] [1N7540] 'CL150 RFFE, Inconel 600, Inconel Trim'
Aluminum Alloys, A
Other Materials, X
7687 = [XCY1W8] [8X7687] 'Gravity Head, Vitrified Clay'
7689 = [XEY1W8] [8X7689] 'Gravity Head, Reinforced Concrete'
7733 = [XTY1U9] [9X7733] 'SCH-80, SE, PVC'
European Piping Material Class Descriptions, 8000-9999
8000 = 'Carbon steel'
8001 = 'Stainless steel'
8002 = 'Forged steel'
8010 = 'Ferritic steel'
8011 = 'Austenitic steel'
8020 = 'Plastic'
8021 = 'Fiber glass'
8030 = 'Glass lined'
8031 = 'Cement lined'
8032 = 'Chloroprene (CR) lined'
9999 = 'Undefined'
The names of Piping Materials Classes are determined as follows:
629
Codelists
o A list includes possible Piping Materials Classes. It consists of
six character names, which are established on the basis of the naming
convention ABCDEF. The meaning of each of the characters in this code
is defined below. Corresponding values are given in the lists
included in subsequent pages.
A.......materials group
B.......materials type
C.......detail features
D.......corrosion allowance or type of lining
E.......service description
F.......pressure rating
o The name of a Piping Materials Class is then determined from the
convention FAXXX, where:
F.......pressure rating
A.......material group
XXX.....sequence number from list in 2090-41-SN
MATERIALS GROUP AND TYPE: (1st and 2nd character)
Irons, F
A= Gray iron
D= Ductile iron
G= Ferritic ductile iron
J= Austenitic ductile iron
Z= Other 1
Carbon Steels, C
A= CS
D= CS, galvanized
G= CS, jacketed
J= CS, killed
M= CS, killed, jacketed
P= CS, low temp
X= Other 1
Y= Other 2
Z= Other 3
630
Codelists
Low
A=
C=
D=
G=
J=
M=
N=
P=
Q=
R=
S=
T=
U=
V=
X=
Y=
Z=
Stainless Steels, S
A= 304
B= 304L
C= 304H
D= 310
E= 316
F= 316L
G= 316H
H= 321
J= 321H
K= 410S
L= CHP10
M= CHP20
N= CPF10MC
O= CPH8
P= CPK20
Q= UNS S31200
R= UNS S31250
S= UNS S31500
T= UNS S31803
U= UNS S32304
V= UNS S32550
W= Alloy 20
X= Other 1
Y= Other 2
Z= Other 3
631
Codelists
Copper Alloys, K
A= Brass
F= Bronze
K= Copper
P= 90Cu-10Ni
R= 70Cu-30Ni
X= Other 1
Y= Other 2
Z= Other 3
Nickel Alloys, N
A= Low C Ni
D= Monel
E= K-Monel
F= R-Monel
G= Inconel 600
H= Inconel 601
J= Inconel 625
L= Incoloy 800
M= Incoloy 800H
N= Incoloy 801
P= Incoloy 802
Q= Incoloy 825
T= Hastelloy B
U= Hastelloy C
V= Hastelloy G
X= Other 1
Y= Other 2
Z= Other 3
Aluminum Alloys, A
C= 3002 aluminum
D= 3003 aluminum
E= 3004 aluminum
F= 5050 aluminum
G= 5052 aluminum
Q= 6061 aluminum
R= 6063 aluminum
S= Alclad
X= Other 1
Y= Other 2
Z= Other 3
632
Codelists
Other Materials, X
A= Asbestos cement
B= Borosilicate glass
C= Clay, vitrified
D= Concrete, prestressed
E= Concrete, reinforced
F= CPVC
G= Epoxy/Glass fib
J= Furan/Carbon
K= Furan/Glass fib
L= Kynar
N= Nylon
P= Polyester/Glass fib
Q= Polyethylene, high dens
R= Polyethylene, low dens
S= Polypropylene
T= PVC
U= Teflon
V= Titanium
W= Zirconium
X= Other 1
Y= Other 2
Z= Other 3
MATERIALS CLASS DETAILS: (3rd character)
A=
B=
C=
D=
E=
F=
G=
H=
J=
K=
L=
M=
N=
0=
P=
Q=
R=
S=
T=
U=
V=
W=
X=
Y=
Z=
633
Codelists
1=
2=
3=
4=
5=
6=
7=
8=
9=
A=
B=
C=
D=
E=
F=
G=
H=
J=
L=
M=
N=
O=
P=
Q=
R=
S=
T=
U=
V=
W=
X=
Y=
Z=
None
0.020"
0.030"
0.050"
0.063"
0.10"
0.125"
0.188"
0.250"
405 clad
410S clad
304 clad
304L clad
316 clad
316L clad
317 clad
317L clad
321 clad
Cement lined
Epoxy lined
Glass lined
Kynar lined
Polyester lined
Polypropylene lined
PTFE lined
Saran lined
Teflon lined
TK31 lined
R11 lined
R15 lined
R18 lined
Other 1
Other 2
634
Codelists
A=
B=
C=
D=
E=
F=
G=
H=
J=
K=
L=
P=
Q=
R=
S=
T=
U=
V=
W=
X=
Y=
Z=
CL150
CL300
CL400
CL600
CL900
CL1500
CL2500
GRAVHD
OTHER
CL125
CL800
CL2000
CL3000
CL4500
CL5000
CL6000
CL9000
CL10000
CL15000
CL20000
CL30000
635
Codelists
=
=
=
=
=
=
=
=
=
=
=
=
=
[Blank]
'By Contractor'
'By Owner'
'By A'
'By B'
'By C'
'By D'
'By E'
'By Equip Vendor'
'By Vendor'
'By Piping'
'By Instruments'
'By Others'
636
=
=
=
=
=
=
=
=
=
=
=
=
=
[Blank]
'CSSF, Contractor supplied, shop fabricated'
'CSFF, Contractor supplied, field fabricated'
'SSSF, Shop supplied, shop fabricated'
'SSFF, Shop supplied, field fabricated'
'FSSF, Field supplied, shop fabricated'
'FSFF, Field supplied, field fabricated'
'ASSF, A supplied, shop fabricated'
'ASFF, A supplied, field fabricated'
'BSSF, B supplied, shop fabricated'
'BSFF, B supplied, field fabricated'
'OSSF, Owner supplied, shop fabricated'
'OSFF, Owner supplied, field fabricated'
Codelists
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
[Blank]
'None'
'Galv'
'PS1.04'
'PS1.07'
'PS1.08'
'PS1.09'
'PS1.10'
'PS1.11'
'PS1.12'
'PS1.13'
'PS2.03'
'PS2.05'
'PS4.01'
'PS4.02'
'PS4.03'
'PS4.04'
'PS4.05'
'PS8.01'
'PS9.01'
'PS10.01'
'PS10.02'
'PS11.01'
'PS12.01'
'PS13.01'
'PS14.01'
'PS16.01'
'PS18.01'
'Varies'
=
=
=
=
[Blank]
'NT'
[Not heat traced]
'HT'
[Heat traced]
'PHT' [Partially heat traced]
637
Codelists
[None]
638
Codelists
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
[Blank]
'N'
'P'
'H'
'HS'
'HF'
'AS'
'C'
'CV'
'CS'
'CH'
'CF'
'S'
'SV'
'R11'
'R15'
'R18'
'Varies'
[Not insulated]
[Personnel protection insulated]
[Hot insulated]
[Hot insulated with sound attenuation]
[Hot insulated with fire protection]
[Anti-sweat insulated]
[Cold insulated]
[Cold insulated vacuum type]
[Cold insulated with sound attenuation]
[Cold and hot insulated]
[Cold insulated with fire protection]
[Sound attenuation insulated]
[Sound attenuation insulation with vapor barrier]
[Refractory lined, insulation]
[Refractory lined, insulation/erosion]
[Refractory lined, erosion]
=
=
=
=
=
=
=
=
[Blank]
'None'
'CC1'
'CC2'
'CC3'
'CC4'
'CC5'
'Varies'
[Flanged end]
integral gaskets; 16-19 for ends with
[Flat-face flanged termination type]
[Flat-face flanged end]
[Flat-face flanged end with integral gasket]
639
Codelists
Use 21-25 for ends without integral gaskets; 26-29 for ends with
integral gaskets.
20 = 'RFTP
(21-29)' [Raised-face flanged termination type]
21 = 'RFFE'
[Raised-face flanged end]
26 = 'RFFEWG'
[Raised-face flanged end with integral gasket]
Use 31-35 for ends without integral gaskets; 36-39 for ends with
integral gaskets.
30 = 'RJFTP
(31-39)' [RTJ-face flanged termination type]
31 = 'RJFE'
[RTJ-face flanged end]
Use 41-45 for ends without
integral gaskets.
40 = 'TMFTP
(41-49)'
41 = 'STFE'
42 = 'LTFE'
43 = 'SMFE'
44 = 'LMFE'
[Groove/female-face flanged
[Small-groove-face flanged
[Large-groove-face flanged
[Small-female-face flanged
[Large-female-face flanged
termination type]
end]
end]
end]
end]
Use 61-65 for lap-flanged ends without integral gaskets; 66-69 for
lap-flanged ends with integral gaskets.
60 = 'FFLFTP
(61-69)' [Flat-face lap-flanged termination type]
61 = 'FFLFE
[Flat-face lap-flanged end]
Use 71-75 for lap-flanged ends without integral gaskets; 76-79 for
lap-flanged ends with integral gaskets.
70 = 'RFLFTP
(71-79)' [Raised-face lap-flanged termination type]
71 = 'RFLFE'
[Raised-face lap-flanged end]
Use 81-85 for lap-flanged ends without integral gaskets; 86-89 for
lap-flanged ends with integral gaskets.
80 = 'RJFLFTP
(81-89)' [RTJ-face lap-flanged termination type]
81 = 'RJLFE'
[RTJ-face lap-flanged end]
Use 91-95 for lap-flanged ends without integral gaskets; 96-99 for
lap-flanged ends with integral gaskets.
90 = 'TMFLFTP
(91-99)' [Tongue/male-face lap-flanged termination
type]
91 = 'STLFE'
[Small-tongue-face lap-flanged end]
92 = 'LTLFE'
[Large-tongue-face lap-flanged end]
93 = 'SMLFE'
[Small-male-face lap-flanged end]
94 = 'LMLFE'
[Large-male-face lap-flanged end]
640
Codelists
Use 101-105 for lap-flanged ends without integral gaskets; 106-109
for lap-flanged ends with integral gaskets.
100 = 'GFFLFTP
(101-109)'[Groove/female-face lap-flanged termination
type]
101 = 'SGLFE'
[Small-groove-face lap-flanged end]
102 = 'LGLFE'
[Large-groove-face lap-flanged end]
103 = 'SFLFE'
[Small-female-face lap-flanged end]
104 = 'LFLFE'
[Large-female-face lap-flanged end]
Use 111-115 for ends without integral
with integral gaskets.
110 = 'FFTBTP
(111-119)'[Flat-face
111 = 'FFTBE'
[Flat-face
116 = 'FFTBEWG'
[Flat-face
gasket]
Use 121-125 for ends without integral gaskets; 126-129 for ends
with integral gaskets.
120 = 'RFTBTP
(121-129)'[Raised-face thru-bolted termination type]
121 = 'RFTBE'
[Raised-face thru-bolted end]
126 = 'RFTBEWG'
[Raised-face thru-bolted end with integral
gasket]
Use 131-135 for ends without integral gaskets; 136-139 for ends
with integral gaskets.
130 = 'RJTBTP
(131-139)'[RTJ-face thru-bolted termination type]
131 = 'RJTBE'
[RTJ-face thru-bolted end]
Use 141-145 for ends without integral gaskets; 146-149 for ends
with integral gaskets.
140 = 'MRJTBTP
(141-149)'[Male RTJ-face thru-bolted termination type]
146 = 'MRJTBEWG'
[Male RTJ-face thru-bolted end with integral
gasket]
Use 151-155 for ends without integral
with integral gaskets.
150 = 'FFTBCSTP (151-159)'[Flat-face
termination type]
151 = 'FFTBCSE'
[Flat-face
156 = 'FFTBCSEWG'
[Flat-face
with integral gasket]
Use 161-165 for ends without integral gaskets; 166-169 for ends
with integral gaskets.
160 = 'RFTBCSTP (161-169)'[Raised-face thru-bolted-with-cap-screws
termination type]
161 = 'RFTBCSE'
[Raised-face thru-bolted-with-cap-screws end]
166 = 'RFTBCSEWG'
[Raised-face thru-bolted-with-cap-screws end
with integral gasket]
641
Codelists
Use 171-175 for ends without integral gaskets; 176-179 for ends
with integral gaskets.
170 = 'RJTBCSTP (171-179)'[RTJ-face thru-bolted-with-cap-screws
termination type]
171 = 'RJTBCSE'
[RTJ-face thru-bolted-with-cap-screws end]
Use 181-185 for ends without integral gaskets; 186-189 for ends
with integral gaskets.
180 = 'FFFTBTP
(181-189)'[Flat-full-face thru-bolted termination type]
181 = 'FFFTBE'
[Flat-full-face thru-bolted end]
186 = 'FFFTBEWG'
[Flat-full-face thru-bolted end with integral
gasket]
190 = 'MJTP
(190-199)'[Mechanical joint termination type]
191 = 'MJE'
[Mechanical joint end]
300 = 'MTP
(301-399)'[Male termination type]
Use 301-309 for welded ends only
301 = 'BE'
[Beveled end]
302 = 'OLET'
[Olet beveled end]
642
Use
311
321
331
341
351
355
361
371
381
Use
391
393
395
400
401
Use
420
421
440
441
460
461
470
471
480
481
500
501
520
521
Codelists
540
541
542
590
=
=
=
=
'BLTP
'BLE'
'MJBE'
'HTP
Use
591
600
601
650
651
643
Codelists
1
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
100
101
102
103
110
644
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
[Blank]
'.0625'
'.125'
'.1875'
'.25'
'.3125'
'.375'
'.4375'
'.5'
'.5625'
'.625'
'.6875'
'.75'
'.8125'
'.875'
'.9375'
'1'
'1.0625'
'1.125'
'1.1875'
'1.25'
'1.3125'
'1.375'
'1.4375'
'1.5'
'1.5625'
'1.625'
'1.6875'
'1.75'
'1.8125'
'1.875'
'1.9375'
'2'
'2.0625'
'2.125'
'2.1875'
'2.25'
'2.3125'
'2.375'
'2.4375'
'2.5'
'2.5625'
'2.625'
'2.6875'
'2.75'
'2.8125'
'2.875'
'2.9375'
'3'
'S-5S'
'S-10S'
'S-40S'
'S-80S'
'S-10'
Codelists
111
112
113
114
115
116
117
118
119
130
131
132
=
=
=
=
=
=
=
=
=
=
=
=
'S-20'
'S-30'
'S-40'
'S-60'
'S-80'
'S-100'
'S-120'
'S-140'
'S-160'
'S-STD'
'S-XS'
'S-XXS'
=
=
=
=
=
=
=
=
=
=
[Blank]
'SC1'
'SC2'
'SC3'
'SC4'
'SC5'
'SC6'
'SC7'
'SC8'
'SC9'
=
=
=
=
[Blank]
'ANR =Analysis not required'
'ATBP=Analysis to be performed'
'AC =Analysis completed'
645
Codelists
646
=
=
=
=
=
=
=
[Blank]
'Piping'
'Piping'
'Piping'
'Piping'
'Hose'
'Tubing'
Codelists
18
19
20
21
22
23
24
25
28
29
30
31
33
34
35
36
39
43
47
49
50
51
54
55
56
57
58
59
60
67
68
70
71
73
74
75
79
86
89
90
93
97
98
99
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
'Gate valve'
'Extended body gate valve'
'Conduit gate valve'
'Blank gate valve'
'3-way valve'
'Ball valve'
[2-way]
'2-way valve'
'3-way ball valve'
'Globe valve'
[2-way]
'Angle globe valve'
[2-way]
'3-way globe valve'
'Y globe valve'
'Plug valve'
[2-way]
'4-way valve'
'3-way plug valve'
'4-way plug valve'
'Needle valve'
'Butterfly valve'
'Diaphragm valve'
'Knife gate valve'
'Slide valve'
[2-way]
'3-way slide valve'
'Angle valve'
'Check valve'
'Wafer check valve'
'Angle check valve'
'Stop check valve'
'Angle stop check valve'
'Y stop check valve'
'Backflow preventer'
'Automatic recirculation valve'
'Angle blowdown valve'
'Y blowdown valve'
'Pinch valve'
'Float valve'
'Foot valve'
'Tank drain valve'
'Deluge valve'
'Hose valve'
'Angle hose valve'
'Vent/drain valve'
'Instrument root valve'
'3-way instrument root valve'
'4-way instrument root valve'
647
Codelists
117
119
120
122
124
126
127
128
129
130
131
132
133
135
137
138
139
140
141
142
143
144
148
151
152
155
156
157
159
160
162
163
165
167
169
171
172
173
175
176
177
179
181
182
184
189
191
192
193
195
196
198
200
202
648
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
'Flange'
'Reducing flange'
'Expander flange'
'Orifice flange'
'Blind flange'
'Open spectacle blank'
'Closed spectacle blank'
'Blank disc'
'Blind spacer'
'Tapered spacer'
'Open spacer'
'End'
'Head'
'Plug'
'Cap'
'Diameter change'
'Concentric diameter change'
'Eccentric diameter change'
'Coupling/connector'
'Half coupling'
'Concentric reducer'
'Eccentric reducer'
'Reducing coupling'
'Concentric swage'
'Eccentric swage'
'Union'
'Orifice union'
'Dielectric union'
'Hose connection'
'Bushing'
'Reducing insert'
'Pipe bend'
'5.625 deg elbow'
'11.25 deg elbow'
'22.5 deg elbow'
'<45 deg direction change'
'45 deg direction change'
'45 deg elbow'
'45 deg LR elbow'
'45 deg long tangent elbow'
'45 deg 3D elbow'
'45 deg union elbow'
'45 deg street elbow'
'45 deg short elbow'
'45 deg long elbow'
'60 deg elbow'
'45-90 deg direction change'
'90 deg direction change'
'90 deg elbow'
'90 deg SR elbow'
'90 deg LR elbow'
'90 deg LR long tangent elbow'
'90 deg reducing elbow'
'90 deg 3D elbow'
Codelists
204
206
207
209
210
216
218
220
222
223
224
229
231
233
237
239
240
242
243
246
249
251
253
260
262
264
265
267
268
269
270
275
277
278
279
285
287
288
289
290
291
292
293
294
295
297
299
303
304
310
312
313
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
649
Codelists
315
316
317
318
319
320
324
325
327
338
339
340
344
345
346
352
353
354
374
380
650
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
'Fire monitor'
'Elevated fire monitor'
'Remotely operated fire monitor'
'Foam monitor'
'Elevated foam monitor'
'Remotely operated foam monitor'
'Fire hydrant'
[2-way]
'Fire hydrant w/monitor nozzle' [2-way]
'3-way fire hydrant'
'Hose reel'
'Hose rack station'
'Foam chamber'
'Wet sprinkler'
'Pre-action sprinkler'
'Spray sprinkler'
'Eye wash'
'Safety shower'
'Safety shower and eye wash'
'Siamese'
[2-way]
'90 deg siamese'
[2-way]
Codelists
513
515
516
517
518
519
521
523
524
525
527
529
533
535
540
542
544
546
548
552
556
557
559
561
563
564
565
567
569
571
576
582
583
584
586
588
590
611
613
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
'Flame arrestor'
'Hammer arrestor'
'Vent silencer'
'In-line silencer'
'Vent'
'Exhaust head'
'Breather vent'
'Free vent w/o screen'
'Free vent w/screen'
'Motor operated valve'
'Mixing T'
'Spray nozzle'
'Removable spool'
'Swing elbow'
'Expansion joint'
'Hinged expansion joint'
'Swivel joint'
'Mechanical coupling'
'Flexible hose'
'Sample cooler'
'Strainer/filter'
'Single basket strainer'
'Duplex basket strainer'
'T strainer'
'Y strainer'
'Temporary strainer'
'Basket strainer'
'Cone strainer'
'Flat plate strainer'
'Sump strainer'
'Filter'
'Steam trap'
'Float steam trap'
'Inverted bucket steam trap'
'Thermostatic steam trap'
'Thermodynamic steam trap'
'Impulse steam trap'
'Generic component'
'Pip seg heat tracing brk/comp 2'
651
Codelists
747
748
749
750
823
824
825
833
873
874
875
876
877
878
879
880
909
911
913
923
927
1008
1018
1019
1020
1038
1039
1040
1041
1042
1043
1044
1045
1047
1049
1053
1068
1069
1070
1071
1072
1073
1074
1075
1079
1083
1108
1117
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
652
Codelists
1500
1501
1502
1503
1504
1505
1506
1507
1508
1509
1510
1511
1512
1513
1514
1515
1516
1517
1518
1519
1520
1521
1522
1523
1524
1525
1526
1527
1528
1529
1530
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
'Valve generic'
'Angle plug valve'
'Non-return valve'
'Check valve'
'Valve with continous action'
'4-way globe valve'
'4-way valve,generic'
'Steam throttling angle valve'
'Steam throttling 3-way globe valve'
'Butterfly valve with continous action'
[Blank]
[Blank]
'Globe valve with continous action'
'Gate valve with continous action'
'Plug valve with continous action'
'Angle globe valve with continous action'
'Free wheel check valve'
'Safety check valve'
'Fire safety butterfly valve'
'Aeration and deaeration armature'
'Angle ball valve'
'4-way ball valve'
'Taper plug valve'
'Taper angle plug valve'
'3-way taper plug valve'
'4-way taper plug valve'
'Flat seal bottom'
'Blank disk'
'Flange connection'
'Screwed connection'
'Angle diaphragm valve'
653
Codelists
1533
1534
1535
1536
1537
1538
1539
1540
1542
1543
1544
1545
1546
1548
1549
1550
1551
1552
1553
1554
1555
1556
1557
1558
1559
1560
1561
1562
1563
1564
1565
1566
1567
1568
1569
1570
1571
1572
1573
1574
1575
1576
1577
1578
1579
1580
1581
1582
1583
1584
1585
1587
1588
1590
654
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
'Safety valve'
'Safety valve regulated with spring'
'Safety valve regulated with weight'
'Angle safety valve'
'Angle safety valve regulated with spring'
'Rupture disk'
'Aeration with screw cap'
'Inspection glass'
'Aeration with plug'
'Flanged aeration'
'90 deg earation'
'180 deg earation'
'Tapered filter'
'Discharge valve with blind flange'
'Discharge valve'
'Discharge with blind flanged gate valve'
'Discharge with gate valve'
'Bellow expansion joint'
'Lyra expansion joint'
'90 degree elbow for JP'
'T connection for JP'
'Flange between JP'
'Valve for connecting JP media'
'Blindflange JP'
'Skewed connection JP'
'Y connection JP'
'flanged connection segment/comp type 1'
'flanged connection segment/comp type 2'
'flanged connection segment/comp type 3'
'flanged connection segment/comp type 4'
'Flange from JP to normal pipe'
'Valve for JP media supply'
'Flange connection for JP'
'Bypass for JP media'
'Flange for bypassing JP'
'Syphon'
'Ball linkage'
'Mixing component'
'Flow straightener'
[Blank]
'Spring clip'
'Fire extinguishing equipment powder'
'Fire extinguishing equipment halogen'
'Fire extinguishing equipment carbonic acid'
'Fire extinguishing equipment foam'
'Fire extinguishing equipment floor connection'
'Fire extinguishing equipment overhead conn.'
'Fire extinguishing connector'
'Fire extinguishing water supply'
'Fire brigade accessory'
'Hydrant ground floor'
'Hydrant overhead'
'Wall hydrant'
'Sprinkler equipment'
Codelists
1591
1592
1593
1594
1595
1596
1597
1598
1599
1600
1601
1602
1603
1604
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
[Blank]
'NO'
'NC'
'CSO'
'CSC'
'LO'
'LC'
'FO'
'FC'
'FL'
'FLO'
'FLC'
'FI'
'EO'
'EC'
'DEO'
'DEC'
[Normally open]
[Normally closed]
[Car seal open]
[Car seal closed]
[Locked open]
[Locked closed]
[Fail open]
[Fail closed]
[Fail locked]
[Fail locked open]
[Fail locked closed]
[Fail indeterminate]
[Energize to open]
[Energize to close]
[De-energize to open]
[De-energize to close]
655
Codelists
Types Options, 11-19
11 = 'Type 1'
12 = 'Type 2'
13 = 'Type 3'
14 = 'Type 4'
15 = 'Type 5'
16 = 'Type 6'
17 = 'Type 7'
18 = 'Type 8'
19 = 'Type 9'
Valve Type Options, 21-60
21 = 'Red port'
24 = 'Full port'
27 = 'Tight SO'
30 = 'Dbl disc'
32 = 'Y pattern'
33 = 'Wafer'
34 = 'Lug'
36 = 'Single flange'
38 = '1/8" hole'
39 = 'Non lube'
40 = '3/16" hole'
41 = '1/4" hole'
42 = 'Lube'
43 = 'Quick close'
44 = 'Quick open'
45 = 'Al chk'
46 = 'Excess flow'
48 = 'Limit stop'
49 = 'Hor chk'
50 = 'Vert chk'
56 = 'Tap lcn G'
57 = 'Tap lcns G & H'
58 = 'Tap lcns G & I'
59 = 'Tap lcns G & J'
60 = 'Tap lcns G & K'
656
Codelists
Bend
121
124
127
130
133
134
136
Head
141
143
145
[Hemispherical head]
[Ellipsoidal head]
[2:1 elliptical head]
[1-cut miter]
[2-cuts miter]
[3-cuts miter]
[4-cuts miter]
657
Codelists
Bolted End Options, 201-400
202 = 'FE'
[Flanged end]
211 = 'FFFE'
[Flat-face flanged end]
216 = 'FFFEWG'
[Flat-face flanged end w/ integral gasket]
221 = 'RFFE'
[Raised-face flanged end]
226 = 'RFFEWG'
[Raised-face flanged end w/ integral gasket]
231 = 'RJFE'
[RTJ-face flanged end]
241 = 'STFE'
[Small-tongue-face flanged end]
242 = 'LTFE'
[Large-tongue-face flanged end]
243 = 'SMFE'
[Small-male-face flanged end]
244 = 'LMFE'
[Large-male-face flanged end]
251 = 'SGFE'
[Small-groove-face flanged end]
252 = 'LGFE'
[Large-groove-face flanged end]
253 = 'SFFE'
[Small-female-face flanged end]
254 = 'LFFE'
[Large-female-face flanged end]
261 = 'FFLFE'
[Flat-face lap-flanged end]
271 = 'RFLFE'
[Raised-face lap-flanged end]
281 = 'RJLFE'
[RTJ-face lap-flanged end]
291 = 'STLFE'
[Small-tongue-face lap-flanged end]
292 = 'LTLFE'
[Large-tongue-face lap-flanged end]
293 = 'SMLFE'
[Small-male-face lap-flanged end]
294 = 'LMLFE'
[Large-male-face lap-flanged end]
301 = 'SGLFE'
[Small-groove-face lap-flanged end]
302 = 'LGLFE'
[Large-groove-face lap-flanged end]
303 = 'SFLFE'
[Small-female-face lap-flanged end]
304 = 'LFLFE'
[Large-female-face lap-flanged end]
311 = 'FFTBE'
[Flat-face thru-bolted end]
316 = 'FFTBEWG'
[Flat-face thru-bolted end w/ integral
gasket]
321 = 'RFTBE'
[Raised-face thru-bolted end]
326 = 'RFTBEWG'
[Raised-face thru-bolted end w/ integral
gasket]
331 = 'RJTBE'
[RTJ-face thru-bolted end]
346 = 'MRJTBEWG'
[Male RTJ-face thru-bolted end w/ integral
gasket]
351 = 'FFTBCSE'
[Flat-face thru-bolted-w/-cap-screws end]
356 = 'FFTBCSEWG'
[Flat-face thru-bolted-w/-cap-screws end w/
integral gasket]
361 = 'RFTBCSE'
[Raised-face thru-bolted-w/-cap-screws end]
366 = 'RFTBCSEWG'
[Raised-face thru-bolted-w/-cap-screws end
w/ integral gasket]
371 = 'RJTBCSE'
[RTJ-face thru-bolted-w/-cap-screws end]
381 = 'FFFTBE'
[Flat-full-face thru-bolted end]
386 = 'FFFTBEWG'
[Flat-full-face thru-bolted end w/ integral
gasket]
391 = 'MJE'
[Mechanical joint end]
658
Codelists
Male
401
402
411
421
431
441
451
455
461
471
481
491
493
495
Female
501 =
521 =
541 =
561 =
581 =
601 =
621 =
641 =
642 =
691 =
[Beveled end]
[Olet beveled end]
[Tapered and beveled end]
[Male flared end]
[Male threaded end]
[Male grooved end]
[Male quick connect end]
[Male clamp end]
[Male ferrule end]
[Male hose end]
[Spigot end]
[Plain end] [391-399]
[Plain end, 3" field fit]
[Plain end, 6" field fit]
[Socket end]
[Socketwelded end]
[Female threaded end]
[Female grooved end]
[Female quick connect end]
[Female ferrule end]
[Female hose end]
[Push-on bell end]
[Mechanical joint bell end]
[Circular hole end]
659
Codelists
Nipple
720 =
721 =
722 =
723 =
724 =
725 =
726 =
727 =
728 =
729 =
730 =
731 =
732 =
733 =
734 =
735 =
736 =
737 =
738 =
739 =
740 =
741 =
742 =
743 =
744 =
745 =
746 =
747 =
748 =
749 =
750 =
751 =
752 =
753 =
754 =
755 =
660
Options, 718-755
'3.0"(75mm) BE'
'3.0"(75mm) MTE'
'3.0"(75mm) PE'
'3.0"(75mm) BE x MTE'
'3.0"(75mm) BE x PE'
'3.0"(75mm) MTE x PE'
'4.0"(100mm) BE'
'4.0"(100mm) MTE'
'4.0"(100mm) PE'
'4.0"(100mm) BE x MTE'
'4.0"(100mm) BE x PE'
'4.0"(100mm) MTE x PE'
'5.0"(125mm) BE'
'5.0"(125mm) MTE'
'5.0"(125mm) PE'
'5.0"(125mm) BE x MTE'
'5.0"(125mm) BE x PE'
'5.0"(125mm) MTE x PE'
'6.0"(150mm) BE'
'6.0"(150mm) MTE'
'6.0"(150mm) PE'
'6.0"(150mm) BE x MTE'
'6.0"(150mm) BE x PE'
'6.0"(150mm) MTE x PE'
'7.0"(175mm) BE'
'7.0"(175mm) MTE'
'7.0"(175mm) PE'
'7.0"(175mm) BE x MTE'
'7.0"(175mm) BE x PE'
'7.0"(175mm) MTE x PE'
'8.0"(200mm) PE'
'9.0"(225mm) PE'
'1O.0"(250mm) PE'
'11.0"(275mm) PE'
'12.0"(300mm) PE'
'HEX'
Codelists
Rating
756 =
757 =
758 =
759 =
760 =
761 =
762 =
763 =
764 =
765 =
766 =
767 =
768 =
769 =
770 =
773 =
774 =
775 =
776 =
777 =
778 =
781 =
782 =
785 =
789 =
790 =
792 =
794 =
795 =
796 =
797 =
801 =
805 =
809 =
813 =
815 =
817 =
821 =
823 =
827 =
831 =
835 =
836 =
838 =
840 =
Options, 756-849
'CL25'
'PN2.5'
'CL50'
'CL75'
'86#'
'CL100'
'CL125'
'CL150'
'175#'
'PN6'
'PN10'
'CL200'
'PN16'
'CL250'
'275#'
'CL300'
'350#'
'PN25'
'PN40'
'CL400'
'PN64'
'CL600'
'PN100'
'CL800'
'CL900'
'PN160'
'1000#'
'PN250'
'PN320'
'PN400'
'CL1500'
'CL2000'
'CL2500'
'CL3000'
'CL4500'
'CL5000'
'CL6000'
'CL9000'
'CL10000'
'CL15000'
'CL20000'
'CL30000'
'SCH 40'
'SCH 80'
'GRAVHD'
661
Codelists
Thickness Options, 851-869
851 = '0.0625"(2mm) thck'
852 = '0.125"(3mm) thck'
853 = '0.1875"(4mm) thck'
854 = '0.25"(6mm) thck'
855 = '0.3125"(8mm) thck'
856 = '0.375"(9mm) thck'
857 = '0.4375"(10mm) thck'
858 = '0.5"(12mm) thck'
859 = '0.5625"(14mm) thck'
860 = '0.625"(16mm) thck'
861 = '0.6875"(18mm) thck'
862 = '0.75"(20mm) thck'
863 = '0.8125"(21mm) thck'
864 = '0.875"(22mm) thck'
865 = '0.9375"(24mm) thck'
866 = '1.0"(25mm) thck'
662
[63 Ra finish]
[60-100 Ra finish]
[80-150 Ra finish]
[200 Ra finish]
[Stock-finish]
Gasket
880 =
881 =
882 =
883 =
884 =
885 =
886 =
887 =
894 =
[Flat gasket]
[Flat full face gasket]
[Corrugated gasket]
[Flat double jacketed gasket]
[Corrugated double jacketed gasket]
[Ring gasket]
[Spiral-wound gasket]
[MSS-SP-44 gasket]
[Special gasket]
Options, 880-899
'F gskt'
'FFF gskt'
'C gskt'
'FDJ gskt'
'CDJ gskt'
'R gskt'
'SW gskt'
'MSS gskt'
'SP gskt'
[Special bolting]
Codelists
Code Options, 911-989
912 = 'ANSI-B16.12'
[Cast iron drainage fittings]
915 = 'ANSI-B16.15'
[Cast bronze fittings]
922 = 'ANSI-B16.22'
[Copper solder joint pressure fittings]
923 = 'ANSI-B16.23'
[Copper solder joint drainage fittings]
924 = 'ANSI-B16.24'
[Bronze flanges]
929 = 'ANSI-B16.36'
[Orifice flanges]
930 = 'ANSI-B16.42'
[Ductile iron flanges and fittings]
933 = 'ANSI-B1.20.3'
[Dryseal pipe threads]
937 = 'ANSI-B1.20.7'
[Hose coupling screw threads]
945 = 'ASTM-A74'
[Cast iron soil pipe and fittings]
949 = 'AWWA-C110'
[Iron fittings]
950 = 'AWWA-C115'
[Iron pipe and fittings]
955 = 'AWWA-C151'
[Ductile iron pipe]
960 = 'AWWA-C207 Cl.B & D, ring' [Steel slip-on flanges CL86, CL150,
CL175]
961 = 'AWWA-C207 Cl.B & D, hub'
[Steel slip-on flanges CL86, CL150,
CL175]
962 = 'AWWA-C207 Cl.E, hub'
[Steel slip-on flanges CL275]
970 = 'API-5LE'
[Polyethylene fittings]
975 = 'API-6A'
[Wellhead flanges and fittings]
979 = 'API-605'
[API-605 flanges]
980 = 'MSS-SP-44-NB'
[MSS non-blind flanges]
981 = 'MSS-SP-44-B'
[MSS blind flanges]
Vendor
990 =
991 =
992 =
993 =
994 =
995 =
996 =
997 =
998 =
999 =
Options, 990-999
'Tube-Turn'
'Dow'
'Aloyco'
'Yarway'
'Teledyne Farris 1'
'R & G Sloane'
'American DI Pipe'
'Gladding McBean' [Vitrified clay S-XS pipe and fittings]
'Taylor Forge'
'ITT VALVES'
663
Codelists
=
=
=
=
=
=
=
=
=
'Piping
'Piping
'Piping
'Piping
'Piping
'Piping
'Piping
'Branch
'Branch
664
Codelists
Notes Applicable to the Piping Materials Class, 2-199
3 = 'Valve and flange protectors required.'
22 = 'Valves shall be in accordance with NACE MR-01-75.'
50 = 'The Manufacturer shall be consulted for special bolting
requirements where both the design temperature is above 800 degF
and the valve bonnet is insulated.'
54 = 'Unions shall not be used.'
56 = 'Gasket seating surfaces shall have 125 Ra surface finish.'
57 = 'Unions shall not be used. Gasket seating surfaces shall
have 125 Ra surface finish.'
58 = 'Unions shall not be used. Gasket seating surfaces shall
have 125 Ra surface finish. Valves shall be in accordance with
NACE MR-01-75.'
60 = 'All welds shall use compatible rod and shall be PWHT
regardless of thickness and/or joint configuration.'
61 = 'All welds shall use compatible rod and shall be PWHT
regardless of thickness and/or joint configuration unless
specifically approved by Contractor and permitted by
ANSI-B31.3 Code.'
62 = 'Refer to AWWA-C151 for suitable installation types.'
63 = 'Underground pipe and fittings shall be coated and wrapped.'
64 = 'Pipe and fittings shall be cement lined.'
79 = 'Extra thickness has been included.'
80 = 'All components shall be bored to suit thickness of pipe.
Taper bore flanges to a depth of 1.5 inches as required to match
inside diameter of all connecting pipingand valves. Welds
shall be ground smooth to match inside diameter of pipe.'
82 = 'Use long radius bends with radius as specified on the P&IDs
for all changes in direction.'
83 = 'Do not allow galvanized or any other zinc bearing material
to come in contact with stainless steel or high nickel
alloys components. This includes supports, nipples, weld
splatter, wire, bolts, paint, or any other type of contact.'
665
Codelists
Notes Applicable to a Piping Component, 200-499
201 = 'To be used only where specifically required.'
202 = 'Use between blind flange and gasket.'
203 = 'Use for thermowell connections.'
204 = 'Use for hydrostatic vents and drains. Seal (bridge) weld
after testing in accordance with piping job specifications.'
205 = 'Use bends for direction changes.'
206 = 'Use at flanged equipment connections.'
207 = 'Use for hydrostatic vents and drains.'
208 = 'Use threaded plug for vent/drain valve; do not seal weld plug.'
209 = 'To be used only where specifically required and/or between
blind flange and gasket.'
210 = 'Use threaded plug for vent/drain valve; do not seal weld
plug. Vent/drain and instrument root valves with 1 inch nominal
diameter in carbon steel and 9Cr-1Mo materials provide more
than 3/16 inch but less than 1/4 inch CA.'
211 = 'Use of this component under certain pressure/temperature
conditions may provide less than 3/16 inch CA.'
214 = 'Use where full port is required.'
220 = 'Install in the horizontal position only.'
221 = 'Valve shall be in accordance with NACE MR-01-75.'
222 = 'Use 0.75 inch diameter only at orifice flange taps.'
223 = 'Use 0.5 inch diameter only at orifice flange taps.'
224 = 'To be used only where specifically required. Valve sizes
16" and larger require electric motor operators.'
253 = 'Use of unions and threaded fittings shall be limited to a
maximum temperature of 500 degF.'
257 = 'When mating stainless steel flanges to ferritic steel
flanges, use studs corresponding to the ferritic flange.'
259 = 'Double hub fittings are available in 90 degrees and 45
degrees elbows.'
260 = 'Cement lined per AWWA-C205-80. Minimum lining thickness
shall be 0.3125 inch thick. Lining shall be Type II cement per
ASTM-C150 with a minimum 28-day compressive strength of
3000 psi. Lining shall be flush with ends.'
276 = 'Remove internals of valves containing Teflon seats and/or
seals prior to welding or backwelding.'
304 = 'For use in deluge systems.'
325 = 'Do not use over 100 degF.'
326 = 'Do not use over 150 degF.'
328 = 'Do not use over 180 degF.'
329 = 'Do not use over 200 degF.'
330 = 'Do not use over 250 degF.'
331 = 'Do not use over 300 degF.'
332 = 'Do not use over 350 degF.'
333 = 'Do not use over 400 degF.'
334 = 'Do not use over 450 degF.'
335 = 'Do not use over 500 degF.'
336 = 'Do not use over 550 degF.'
337 = 'Do not use over 600 degF.'
338 = 'Do not use over 650 degF.'
339 = 'Do not use over 700 degF.'
340 = 'Do not use over 750 degF.'
341 = 'Do not use over 800 degF.'
666
Codelists
Notes Applicable to a Piping Specialty, 500-699
Notes Applicable to an Instrument Specialty, 700-899
Type, 2-99
=Actuator'
=Alarm'
=Controller'
=Indicator'
=Positioner'
=Recorder'
=Switch'
=Transmitter'
=Unclassified'
=Converter'
667
Codelists
1 = [Blank]
Operators with Data Derived from Spec Parameters, 2-24
3 = 'Handwheel'
4 = 'Handwheel if GCP > RCP'
5 = 'Handwheel, inclined'
9 = 'Wrench, short'
11 = 'Wrench, long'
17 = 'Lever'
19 = 'T-handle, short'
21 = 'T-handle, long'
Operators with Data Derived from Valve Codes, 25-40
25 = 'Handwheel, special'
27 = 'Wrench, special'
29 = 'Gear, top mounted handwheel'
31 = 'Gear, top mounted inclined handwheel'
33 = 'Gear, side mounted handwheel'
35 = 'Gear, side mounted inclined handwheel'
39 = 'Lever, quick-action'
40 = 'Post indicator'
Actuators, 41-99
41 = 'Diaphragm'
42 = 'Electro-Pneumatic'
43 = 'Press-balanced diaphragm'
45 = 'Regulator'
49 = 'Single acting cylinder'
51 = 'Double acting cylinder'
53 = 'Pilot operated cylinder'
57 = 'Motor'
61 = 'Digital'
65 = 'Electro-hydraulic'
69 = 'Single solenoid'
71 = 'Single solenoid w/reset'
73 = 'Double solenoid'
77 = 'Pilot'
81 = 'Weight'
85 = 'Manual'
89 = 'Spring'
91 = 'Capacitance sensor'
93 = 'Ball float'
95 = 'Displacement float'
97 = 'Paddle wheel'
668
Codelists
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
[Blank]
'ASME-I'
[Power Boilers]
'ASME-III'
[Nuclear]
'ASME-VIII-1'
[Unfired Vessels]
'ASME-VIII-2'
[Unfired Vessels]
'ASME Fld Mets & AGA Rpt 3' [Instruments]
'ANSI-B31.1'
[Power]
'ANSI-B31.2'
[Fuel Gas]
'ANSI-B31.3'
[Petroleum]
'ANSI-B31.4'
[Oil Transport]
'ANSI-B31.5'
[Refrigeration]
'ANSI-B31.8'
[Gas Transmission]
'ANSI-B31.9'
[Building Services]
'API-2000'
[Tank Venting]
'AWWA'
[Water Services]
'DIN'
'BS806'
'BS3351'
US practices
European practices 1 (DIN)
European practices 2 (British)
European practices 3 (Finnish, French, etc.
International practices 1 (JIS)
International practices 2 (Australian, etc.)
Company practices
2-6999
7000-11999
12000-16999
17000-19999
20000-24999
25000-27999
28000-31999
1 = [Blank]
669
Codelists
US Practice Geometry Standards, 2-6999
6 = 'PDS-P1'
[REDE, RWELD, RPAD, BLSPC_>24"_API+/- thk varies,
BLSPO_>24"_API+/- thk varies]
7 = 'PDS-P2'
[BLSPC_>24"__API+/-_0.375"thk,
BLSPO_>24"_API+/-_0.375"thk]
8 = 'PDS-P3'
[BLSPC_>24"_MSS+/- thk varies, BLSPO_>24"_MSS+/thk varies]
11 = 'PDS-I1'
[BLSPC_>24"_API+/-_1.5"thk,
BLSPO_>24"_API+/-_1.5"thk]
12 = 'PDS-I2'
[BLPAD_>24"_MSS+/-_0.75"thk,
BLSPA_>24"_MSS+/-_0.75"thk]
13 = 'PDS-I3'
16 = 'PDS-Op1'
17 = 'PDS-Op2'
18 = 'PDS-Op3'
31 = 'ANSI-B16.1'
[Cast Iron Pipe Flanges and Flanged Fittings ||]
33 = 'ANSI-B16.3'
[Malleable Iron Threaded Fittings ||]
34 = 'ANSI-B16.4'
[Cast Iron Threaded Fittings ||]
35 = 'ANSI-B16.5'
[Pipe Flanges and Flanged Fittings ||]
39 = 'ANSI-B16.9'
[Steel Beveled End Fittings ||]
40 = 'ANSI-B16.10' [Dimensions of Ferrous Valves ||]
41 = 'ANSI-B16.11' [Forged Steel Socketwelded and Threaded Fittings ||]
42 = 'ANSI-B16.12' [Cast Iron Threaded Drainage Fittings ||]
44 = 'ANSI-B16.14' [Ferrous Pipe Plugs and Bushings]
45 = 'ANSI-B16.15' [Cast Bronze Threaded Fittings ||]
50 = 'ANSI-B16.20' [RTJ Gaskets and Grooves ||]
51 = 'ANSI-B16.21' [Flat Gaskets for Pipe Flanges ||]
52 = 'ANSI-B16.22' [Wrought Copper Solder Joint Pressure Fittings ||]
53 = 'ANSI-B16.23' [Cast Copper Solder Joint Drainage Fittings ||]
54 = 'ANSI-B16.24' [Bronze Pipe Flanges and Flanged Fittings ||]
55 = 'ANSI-B16.25' [Beveled End Preparation]
56 = 'ANSI-B16.26' [Cast Copper Alloy Fittings for Flared Copper
Tubing]
58 = 'ANSI-B16.28' [Steel Beveled End Short Radius Elbows and Returns
||]
59 = 'ANSI-B16.29' [Wrought Copper Solder Joint Drainage Fittings]
64 = 'ANSI-B16.34' [Valves Flanged and Beveled Ends ||]
66 = 'ANSI-B16.36' [Steel Orifice Flanges ||]
69 = 'ANSI-B16.39' [Malleable Iron Threaded Pipe Unions ||]
72 = 'ANSI-B16.42' [Ductile Iron Pipe Flanges and Flanged Fitting ||]
73 = 'ANSI-B16.43' [Wrought Copper Alloy Solder Joint Fittings for
Solvent
Drainage Systems]
81 = 'ANSI-B18.2.1' [Square and Hex Bolts and Screws ||]
82 = 'ANSI-B18.2.2' [Square and Hex Nuts]
100 = 'ANSI-B36.10M' [Welded and Seamless Wrought Steel Pipe ||]
109 = 'ANSI-B36.19M' [Stainless Steel Pipe ||]
670
Codelists
114 = 'API-5A'
115 = 'API-5B'
119 = 'API-5L'
120 = 'API-5LE'
122 = 'API-5LP'
124 = 'API-5LS'
126 = 'API-5LU'
127 = 'API-5LX'
131 = 'API-6A'
132 = 'API-6AB'
135 = 'API-6D'
Swivels]
141 = 'API-526'
145 = 'API-590'
146 = 'API-590Z1'
147 = 'API-590Z2'
153 = 'API-593'
154 = 'API-594'
155 = 'API-595'
157 = 'API-597'
159 = 'API-599'
160 = 'API-600'
161 = 'API-601'
162
163
164
165
166
169
171
172
Pipe]
173
= 'API-602'
= 'API-603'
= 'API-604'
= 'API-605'
= 'API-606'
= 'API-609'
= 'ASTM-A74'
= 'ASTM-C76'
174
176
||]
177
||]
179
181
184
186
= 'ASTM-D2464'
= 'ASTM-D2466'
= 'ASTM-D2467'
=
=
=
=
= 'ASTM-C700'
'AWWA-C106'
'AWWA-C110'
'AWWA-C115'
'AWWA-C151'
671
Codelists
190=
672
Codelists
1000 = 'Adamson 1'
1001 = 'Adams 1'
1025 = 'Aitken 1' [BLPAD; BLSPA; TDRA; TDRB; TDRBW ||]
1026 = 'Aitken Z1' [BLPAD; BLSPA - with 0.125" CA ||]
1027 = 'Aitken Z2' [BLPAD; BLSPA - with 0.25" CA ||]
1050 = 'Allied Pipe Products 1'
1075 = 'Aldo Colombo 1'
1100 = 'Aloyco 1' [GATR-Fig_114; GATR-Fig_114DB; GATR-Fig_114EB;
GATR-Fig_124;
GATR-Fig_2214A; GLOR-Fig_2310A; GLOR-Fig_2314A; GLOR-Fig_314;
GLOR-Fig_314DB;
GLOR-Fig_314EB; GLOR-Fig_504; CKLR-Fig_554; CKLR-Fig_2554A;
CKSR-Fig_2374;
CKSR-Fig_374; TKDR-Fig_751 ||]
1101 = 'Aloyco 2' [GATR-Fig_2110; GATR-Fig_2114 ||]
1125 = 'American Darling 1' [H3W1-Fig_B-50-B ||]
1130 = 'American DI Pipe' [PIPE; L; LRB ||]
1150 = 'American Valve 1'
1175 = 'Amri 1'
1200 = 'Anaconda 1'
1225 = 'Anderson Greenwood 1'
1250 = 'Anvil 1'
1275 = 'A.O.Smith 1'
1300 = 'Apollo 1'
1325 = 'Argus 1'
1350 = 'Armstrong 1' [S51AC-Fig_K1SC; S70AC-Fig_2011; S70BC-Fig_2011 ||]
1375 = 'Asahi/American 1'
673
Codelists
1400
1425
1450
1475
1500
1525
1550
1560
1575
= 'Babbitt 1'
= 'Babcock and Wilcox 1'
= 'Badger Meters 1'
= 'Bailey Co 1'
= 'Balon 1'
= 'Basic Engineering 1'
= 'Bestobel 1'
= 'Bete 1' [SSP1-Series_N ||]
= 'Bonney Forge 1' [GAT-Fig_9HLF-10; GATR-Fig_9H-10; GATR-Fig_9W-10;
GATEXB-Fig_VLL-10; GATEXB-Fig_VOLL-10; GLOR-Fig_HL-30;
GLOR-Fig_9HL-30;
GLOR-Fig_9WL-30; CKLR-Fig_9HL-40; CKLR-Fig_9HL-50;
CKLR-Fig_9HL-60;
CKLR-Fig_9WL-40; CKLR-Fig_9WL-50; CKLR-Fig_9WL-60;
CKLR-Fig_HL-40;
CKLR-Fig_9HLF-40; CKLRY-Fig_9Y-40; CKLRY-Fig_25Y-40; CAPOT; UN;
L; LRB;
SWOL; WOL; SOL; TOL; NOL; EOLLR; EOLSR; LOL ||]
1576 = 'Bonney Forge 2' [GATR-Fig_9H-10; GATR-Fig_25W-10;
GLOR-Fig_9HL-30;
GLOR-Fig_9WL-30; GLOR-Fig_25W-30; GLOY-Fig_25Y-30;
CKLR-Fig_9HL-40;
CKLR-Fig_9HL-50; CKLR-Fig_9HL-60; CKLR-Fig_9WL-40;
CKLR-Fig_9WL-50;
CKLR-Fig_9WL-60 ||]
1577 = 'Bonney Forge 3' [GATF-Fig_H-10; GATF-Fig_W-10; GATR-Fig_HL-10;
GATR-Fig_WL-10; CKLR-Fig_HL-40; CKLR-Fig_WL-40 ||]
1585 = 'Boots & Coots 1' [MN1-Spectrum_Allpha_6235 ||]
1590 = 'Bray 1'
1600 = 'Brooks Meters 1'
1625 = 'Cameron 1'
1650 = 'Carbone 1'
1675 = 'Ciba-Geigy 1'
1700 = 'Clark Reliance 1'
1725 = 'Clayton Automatic Valves 1' [CKBP-Model_D; FLO-Series_427-01 ||]
1750 = 'Clayton Mark 1'
1775 = 'Clow 1'
1800 = 'Cochrane 1'
1825 = 'Condren 1'
1850 = 'Continental Emsco 1'
1875 = 'Cooper Valve 1'
1900 = 'Crane 1' [GATF-Fig_3904U; GATR-Fig_424; GATR-Fig_431UB;
BALR-Fig_9302;
GLOF-Fig_3944U; GLOR-Fig_14 1/2P; GLOR-Fig_70; GLOY-Fig_7189;
NEE-Fig_88;
CKS-Fig_373;CKLF-Fig_3973U; CKSR-Fig_36; CKSR-Fig_137;
FOOT-Fig_394;
FOOT-Fig_395; FLWN; FSO; L; LRB ||]
1925 = 'Crosby 1'
674
Codelists
1950
1975
2000
2025
2050
2075
2100
2150
2155
2175
2200
2225
2250
2275
2300
2325
2350
2375
2400
2425
2450
2475
2500
2525
2550
2575
2600
2625
2650
2660
2675
2700
||]
2715
2725
2750
2775
2800
2825
2850
2860
2875
2900
2915
2925
2950
2975
2980
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
'Daniel 1'
'Demco 1'
'Dezurik 1'
'Dixon 1'
'Dresser 1'
'Dover 1'
'DOW 1' [TRI-Lining_SL; TRI-Lining_PPL, TRI-Lining_KL ||]
'Duo Seal 1'
'Dur-O-Lock 1' [CPL ||]
'Durco 1'
'Elkhart 1'
'Enpro 1'
'Epsco 1'
'Everest 1'
'Fabri-Valve 1' [KNF-Fig_36 ||]
'Fairbanks 1'
'Fasani 1'
'Fetterolf 1'
'Fibercast 1'
'Fike 1'
'Fisher 1'
'Flexitallic 1'
'Flowline 1'
'FMC 1'
'Foxboro 1'
'Garlok 1'
'General 1'
'Geosource 1'
'Gestra 1'
'Gladding McBean 1' [REDC; E45; E90; M451; M452; L ||]
'Graylock 1'
'Grinnell 1' [BALR-Fig_3022; CAPOT; UNO; E45U; E90RST; TOUB; TOUR
675
Codelists
3000 = 'Jacoby Tarbox 1'
3025 = 'Jamesbury 1' [BALR-Style_B; BALSP-Type_530S; BAL3W-Style_AM150FD;
BAL3W-Style_DM150FD ||]
3026 = 'Jamesbury 2' [BALR-Style_A ||]
3027 = 'Jamesbury 3' [BALR-Type_2000_Brass ||]
3028 = 'Jamesbury 4' [BALF-Type_4000; BALR-Type_4000 ||]
3050 = 'Jenkins 1'
3075 = 'Jerguson 1'
3100 = 'Judd Valve 1'
3125 = 'Kamyr-Neles 1'
3150 = 'Kemp 1'
3175 = 'Kennedy 1'
3200 = 'Keystone 1'
3225 = 'Kinka Kikai 1'
3250 = 'Kitz 1'
3275 = 'KTM 1'
3300 = 'Kubota 1'
3325 = 'L & M Valve 1'
3350 = 'Ladish 1' [CAPOT; L; LRB ||]
3375 = 'Lamons 1'
3400 = 'Lukens 1'
3425 = 'Lunkenheimer 1'
3445 = 'Mac-Iron 1'
3450 = 'Magnetrol 1'
3475 = 'Malbranque 1'
3500 = 'Maloney 1'
3525 = 'Mark Controls/Centerline 1' [BFYLP-Series_A; BFYLP-Series_LT;
BYFLP-Series_504 ||]
3550 = 'Mark Controls/Flowseal 1' [BFYHP-Style_1LB ||]
3575 = 'Mark Controls/Marpac 1'
3600 = 'Mark Controls/Pacific 1' [GATSP-Fig_21555; GATSP-Fig_55509;
GATSP-Fig_55515;
GLOSP-Fig_56009; GLOSP-Fig_56015; CKSSP-Fig_58809-5-WE;
CKSSP-Fig_58815-7-WE;
CKST-Fig_160S ||]
3625 = 'Marlin 1'
3650 = 'Marwin 1'
3675 = 'Masoneilan 1'
3700 = 'Media 1' [BFYLP]
3725 = 'Milwaukee 1'
3750 = 'Mueller/Muessco Brass 1'
3775 = 'Mueller/Muessco Steam Specialty 1' [S51AC-Fig_761WE;
S51AC-Fig_862BC;
S51AC-Fig_762 ||]
3800 = 'Navco 1'
3825 = 'Nells 1'
3850 = 'Newco 1'
3860 = 'Nibco 1'
3875 = 'Nicholson 1' [S78AC-Fig_N302L ||]
3900 = 'Nippon-Benkan 1' [BW fittings above 48" ||]
3925 = 'Nupro 1'
3950 = 'OPW 1'
3975 = 'Orbit 1'
4000 = 'Oseco 1'
676
Codelists
4025
4030
4050
4075
4100
4125
4150
4175
4200
||]
4225
4250
4275
4300
4325
4335
4350
4375
4400
4425
=
=
=
=
=
=
=
=
=
677
Codelists
4520 = 'Sarco 1'
4522 = 'Saunders 1'
4525 = 'Sella 1'
4550 = 'Serck Audco 1'
4575 = 'Serfilco 1'
4600 = 'Shoritsu 1'
4625 = 'Smith 1' [GATF-Fig_888; GATF-Fig_5870; GATR-Fig_800;
GATR-Fig_870;
GATR-Fig_1500; GATR-Fig_1570; GATEX-Fig_811 & 812 MPE/THD;
GATEX-Fig_876
& 877 MPE/THD; GATEXB-Fig_874 & 875 OLET/THD; GATXBA-Fig_874 & 875
OLET/SW;
GATXBB-Fig_874 & 875 OLET/THD; GLOR-Fig_G80; GLOR-Fig_G87;
GLOR-Fig_G150;
GLOR-Fig_G157; CKLR-Fig_B80; CKLR-Fig_C80; CKLR-Fig_C150;
CKLR-Fig_SB80;
CKLR-Fig_SC80 ||]
4626 = 'Smith 2' [GATEX-Fig_813 & 814 MPE/SW; GATEX-Fig_878 & 879 MPE/SW
||]
4650 = 'Spraying Systems 1'
4675 = 'Spirax Sarco 1'
4700 = 'Stanco 1'
4725 = 'Standard Fittings 1' [CAPOT; SWGC; SWGE ||]
4750 = 'Stang Hydronics 1' [M1-Fig BB0309-21 w/shapertip nozzle; ME1-Fig
BB3561 ||]
4751 = 'Stang Hydronics 2' [M1-Fig_BB0309-21 w/fog nozzle; ME1-Fig B22999
||]
4752 = 'Stang Hydronics 3' [ME1-Fig_BB3561 composite, w/monitor nozzle
||]
4753 = 'Stang Hydronics 4' [ME1-Fig_BB3377 composite, w/monitor nozzle ||]
4775 = 'Stockham 1'
4800 = 'Strahman 1'
4825 = 'Swagelok 1'
4850 = 'Tapco 1'
4875 = 'Taylor 1'
4900 = 'Taylor Forge 1'
4901 = 'Taylor Forge 2, Rev 1957' [L; S-STD WT ||]
4925 = 'Teledyne Farris 1'
4950 = 'Texas Bolt 1'
4975 = 'Thevignot 1'
5000 = 'Titeflex 1'
5025 = 'TK 1'
5050 = 'TKM 1' [GAT-Fig_100 ||]
5060 = 'Top Line 1'
5075 = 'Triangle 1'
5085 = 'Tri-Clover 1'
5100 = 'Truflo 1'
5125 = 'TRW/Mission 1' [||]
5150 = 'Tubeturn 1' [FWN; FEWN; FOWNA; FOWNB; CAPBV; E453D; E90LT; E903D;
L; SAD ||]
5175 = 'Tufline 1'
5200 = 'Tyler 1' [CPL; REDC; E45LT; E90LT; L ||]
678
Codelists
5225
5250
5275
5300
5325
5350
5375
= 'Valvotecnic 1'
= 'Vanessa 1'
= 'Velan 1' [S3AC-Fig_N675 ||]
= 'Victaulic 1'
= 'Viking 1'
= 'Vitas 1'
= 'Vogt 1' [GATR-Series_15373; GLOR-Series_15141; CKLR-Series_15701;
NEE-Series_22461; NEE-Series_SW22461; CAPOT; UN; E90U; E90ST; L ||]
5400 = 'Wada 1'
5425 = 'Wallworth 1'
5450 = 'Watts Regulator 1'
5475 = 'Weco 1'
5500 = 'WFI 1'
5525 = 'Winston 1' [S49AC-T-Strainer Type-59 W/flg'd cover;
S53AC-Basket-StrainerFig 51-WIP W/CL150 flg'd cover & 3/4" SWE drain||]
5535 = 'Wirt & Knox 1'
5550 = 'WKM 1'
5575 = 'Worcester 1'
5600 = 'Yarway 1' [CKAR-Fig_5301; CKAR-Fig_5302; BDA-Fig_6909-C;
BDY-Fig_6911-C;
TKDR-Fig_8106 ||]
5625 = 'Yoneki 1'
5650 = 'Zurn 1'
o European practices 1 (DIN)
General
7000 =
7001 =
7002 =
Specifications
'DIN 2401-1 Pressure, nominal'
'DIN 2401-2 Pressure, nominal'
'DIN 2402 Diameter,nominal'
Pipes
7010
7011
7012
7013
7014
7015
7016
7017
7018
7019
7020
7025
7026
7030
7031
7040
7041
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
2448'
2458'
2440'
2441'
2442'
2445'
2460'
2462'
2463'
2391'
2393'
2848'
2873'
2462'
2463'
8062'
8077'
7000-11999
679
Codelists
Flanges
7100 =
7101 =
7102 =
7103 =
7104 =
7105 =
7106 =
7107 =
7108 =
7109 =
7110 =
7111 =
7112 =
7113 =
7114 =
7115 =
7116 =
7117 =
7118 =
7119 =
7120 =
7121 =
7122 =
7123 =
7124 =
7125 =
7126 =
7127 =
7128 =
7129 =
7130 =
7131 =
7132 =
7133 =
7134 =
7135 =
7136 =
7137 =
7138 =
7139 =
7140 =
7141 =
7142 =
7143 =
7144 =
7145 =
7146 =
7147 =
7148 =
7149 =
7150 =
7160 =
680
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
2530'
2531'
2532'
2533'
2534'
2535'
2543'
2544'
2545'
2546'
2547'
2548'
2549'
2550'
2551'
2558'
2561'
2565'
2566'
2567'
2568'
2569'
2630'
2631'
2632'
2633'
2634'
2635'
2636'
2637'
2638'
2628'
2629'
2627'
2673'
2667'
2668'
2669'
2573'
2576'
2641'
2642'
2652'
2653'
2655'
2656'
2501'
2512'
2512'
2513'
2514'
2527'
Codelists
7161 = 'DIN 2848'
7162 = 'DIN 2873'
Elbows
7200 =
7201 =
7202 =
7203 =
7204 =
7205 =
7206 =
7210 =
7211 =
7212 =
7213 =
7214 =
7215 =
7216 =
7217 =
7218 =
7219 =
7230 =
7231 =
7240 =
7241 =
7242 =
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
Reducers
7300 = 'DIN
7301 = 'DIN
7302 = 'DIN
7303 = 'DIN
7304 = 'DIN
7310 = 'DIN
7311 = 'DIN
7320 = 'DIN
7321 = 'DIN
7322 = 'DIN
7323 = 'DIN
2616'
2990'
2988'
2950'
2950'
2848'
2873'
16962'
16962'
16962'
16962'
Branches
7400 = 'DIN
7401 = 'DIN
7402 = 'DIN
7403 = 'DIN
7404 = 'DIN
7405 = 'DIN
7406 = 'DIN
7410 = 'DIN
7411 = 'DIN
7420 = 'DIN
7421 = 'DIN
7422 = 'DIN
7423 = 'DIN
2615'
2618'
2618'
2619'
2987'
2987'
2950'
2848'
2873'
16962'
16962'
16962'
16962'
681
Codelists
Caps
7500
7501
7502
7510
7511
=
=
=
=
=
Other
7600
7601
7602
7603
7604
7605
7606
7610
fittings
= 'DIN 2981'
= 'DIN 2982'
= 'DIN 2982'
= 'DIN 2986'
= 'DIN 2990'
= 'DIN 2991'
= 'DIN 2993'
= 'DIN 2950'
'DIN
'DIN
'DIN
'DIN
'DIN
2617'
2991'
2950'
16962'
16962'
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
'DIN
2690'
2691'
2692'
2693'
2695'
2696'
2697'
2698'
Valves
9000 =
9010 =
9020 =
9030 =
9040 =
9050 =
'Non
'DIN
'DIN
'DIN
'DIN
'DIN
Dummy standard
9999 = 'Dummy DIN Std' ; Used for engineered items and instruments
British Standards geometry standards 12000-16999
682
Codelists
sub ranges (provisional) :12000-12099 pipes
12100-12199 flanges
12200-12599 fittings
12600-12999 valves
13000-13199 bolts
13200-13499 gaskets
PIPES
12000
12001
12002
12003
12004
12010
12015
=
=
=
=
=
=
=
'BS3600
'BS3600
'BS3600
'BS3600
'BS3600
'BS1387
'BS1600
FLANGES
12100 = 'BS4504 p1 steel flanges for pipe,valves and fittings'
12101 = 'BS4504 p1 iron flanges for pipe,valves and fittings - tbi'
12110 = 'BS1560 p2 steel pipe flanges Metric dimensions'
FITTINGS
12200 = 'BS1740
12210 = 'BS1965
12220 = 'BS3799
12221 = 'BS3799
12230 = 'BS1640
VALVES
12600 =
12620 =
12625 =
12630 =
12635 =
12640 =
12645 =
12646 =
12650 =
12651 =
12655 =
12656 =
12660 =
12661 =
12665 =
12666 =
12670 =
12671 =
'BS2080 flanged
'BS5150'
'BS5151'
'BS5152'
'BS5153'
'BS5154'
'BS5155'
'BS5155 and app
'BS5156'
'BS5156 and app
'BS5157'
'BS5157 and app
'BS5158'
'BS5158 and app
'BS5159'
'BS5159 and app
'BS5160'
'BS5160 and app
A'
A'
A'
A'
A'
A'
gaskets
13001 = 'BS4865:part 1 - non-metallic for BS4504 flanges'
13002 = 'BS4865:part 2 - spiral wound for BS4504 flanges'
13010 = 'BS3381 - spiral wound for BS1560 flanges'
683
Codelists
bolting
13200 = 'BS4882 metric series bolting'
13210 = 'BS4882 inch series bolting'
dummy
13999 = 'dummy BS code'
US practices
European practices 1 (DIN)
European practices 2 (British)
European practices 3 (Finnish, French, etc.
International practices 1 (JIS)
International practices 2 (Australian, etc.)
Company practices
2-99
100-199
200-299
300-399
400-499
500-599
900-999
1 = [Blank]
US Practice Table Suffixes, 2-99
5 = 'Default'
[See below for definition]
6 = 'PDS-1'
[See specific table for details]
7 = 'PDS-2'
[See specific table for details]
8 = 'PDS-3'
[See specific table for details]
10 = 'ID Duct'
[Nominal diameter based on inside diameter]
12 = 'ANSI-B16.12'
[Cast iron drainage fittings]
15 = 'ANSI-B16.15'
[Cast bronze fittings]
22 = 'ANSI-B16.22'
[Copper solder joint pressure fittings]
23 = 'ANSI-B16.23'
[Copper solder joint drainage fittings]
24 = 'ANSI-B16.24'
[Bronze flanges]
29 = 'ANSI-B16.36'
[Orifice flanges]
30 = 'ANSI-B16.42'
[Ductile iron flanges and fittings]
33 = 'ANSI-B1.20.3' [Dryseal pipe threads]
37 = 'ANSI-B1.20.7' [Hose coupling screw threads]
40 = 'ASME BPE-97 (PE)'
41 = 'ASME BPE-97 (MCE)'
45 = 'ASTM-A74'
[Cast iron S-XH soil pipe and fittings]
46 = 'ASTM-C76'
[Reinforced Concrete Culvert, Storm Drain and Sewer
Pipe]
47 = 'ASTM-C700'
[Extra Strength and Standard Strength Clay Pipe and
Perforated
Clay Pipe]
49 = 'AWWA-C110'
[Iron fittings]
50 = 'AWWA-C115'
[Iron pipe and fittings]
55 = 'AWWA-C151'
[Ductile iron pipe]
60 = 'AWWA-C207 Cl.B & D, ring'
[Steel slip-on flanges CL86, CL150, CL175]
61 = 'AWWA-C207 Cl.B & D, hub'
[Steel slip-on flanges CL86, CL150, CL175]
62 = 'AWWA-C207 Cl.E, hub'
[Steel slip-on flanges CL275]
684
Codelists
70 = 'API-5LE'
75 = 'API-6A'
79 = 'API-605-B'
flange and
80
81
85
86
87
88
90
91
92
93
94
95
96
97
98
99
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
[Polyethylene fittings]
[Wellhead flanges and fittings]
[API-605 blind flanges. These are based on API-605
685
Codelists
All thru-bolted...................For sizes and ratings for which API-590
applies,
the value of parameter "P" shall be
taken from
API-590. For sizes and ratings for
which API-590
does not apply, the bolt circle diameter
from
ANSI-B16.1, B16.5, API-605 or
MSS-SP-42, in that
order of precendence, less one bolt
diameter less
1/8 inch will be used for parameter "P".
Male RTJ-face thru-bolted with cap screws........................None
Flat-face thru-bolted with cap screws........................None
Raised-face thru-bolted with cap screws........................None
RTJ-face thru-bolted with cap screws........................None
Flat-full-face thru-bolted........DOW
Male..............................ANSI-B36.10M, ANSI-B36-19M, API-5L,
API-5LE,
API-5LP, API-5LS or API-5LU
PVC & CPVC socket.................API-5LP, ASTM-D2466 or ASTM-D2467
Socketwelded......................For pressure ratings XXXX#s, per basis
defined
in the applicable generic tables;
for pressure ratings CLXXXXs and
OTXXXXs, per
ANSI-B16.11 and ANSI-B16.5.
Female threaded
thread engagement per Table 2.4 of
2630-33
..................................Forged steel.For pressure ratings
XXXX#s, per basis
defined in the applicable generic
tables; for
pressure ratings CLXXXXs and OTXXXXs,
per ANSI-B16.11
and ANSI-B16.5. In all cases, thread
engagement
will be per Table 2.4 of 2630-33
descriptions in the applicable generic
tables.
In all cases, thread engagement will be
per
Table 2.4 of 2630-33
Female grooved....................Victaulic catalog G100E
Female quick connect..............
Female ferrule....................
Female hose.......................
Mechanical joint bell.............AWWA-C110
Gasket............................Not applicable
Bolt..............................Not applicable
Nut...............................Not applicable
User defined......................None
686
Codelists
o European practices 1 (DIN)
100-199
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
British Standards
205 = 'default metric'
206 = 'default converted imperial'
210 = 'plate flanges BS4504'
687
Codelists
688
Codelists
70 = 'API-5LE'
75 = 'API-6A'
79 = 'API-605-B'
flange and
80
81
85
86
87
90
91
92
93
94
95
96
97
98
99
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
[Polyethylene fittings]
[Wellhead flanges and fittings]
[API-605 blind flanges. These are based on API-605
689
Codelists
All thru-bolted...................For sizes and ratings for which API-590
applies,
the value of parameter "P" shall be
taken from
API-590. For sizes and ratings for
which API-590
does not apply, the bolt circle diameter
from
ANSI-B16.1, B16.5, API-605 or
MSS-SP-42, in that
order of precendence, less one bolt
diameter less
1/8 inch will be used for parameter "P".
Male RTJ-face thru-bolted with
cap screws........................None
Flat-face thru-bolted with
cap screws........................None
Raised-face thru-bolted with
cap screws........................None
RTJ-face thru-bolted with
cap screws........................None
Flat-full-face thru-bolted........DOW
Male..............................ANSI-B36.10M, ANSI-B36-19M, API-5L,
API-5LE,
API-5LP, API-5LS or API-5LU
PVC & CPVC socket.................API-5LP, ASTM-D2466 or ASTM-D2467
Socketwelded......................For pressure ratings XXXX#s, per basis
defined
in the applicable generic tables;
for pressure ratings CLXXXXs and
OTXXXXs, per
ANSI-B16.11 and ANSI-B16.5.
Female threaded
thread engagement per Table 2.4 of
2630-33
..................................Forged steel.For pressure ratings
XXXX#s, per basis
defined in the applicable generic
tables; for
pressure ratings CLXXXXs and OTXXXXs,
per ANSI-B16.11
and ANSI-B16.5. In all cases, thread
engagement
will be per Table 2.4 of 2630-33
descriptions in the applicable generic
tables.
In all cases, thread engagement will be
per
Table 2.4 of 2630-33
Female grooved....................Victaulic catalog G100E
Female quick connect..............
Female ferrule....................
Female hose.......................
Mechanical joint bell.............AWWA-C110
690
Codelists
Gasket............................Not applicable
Bolt..............................Not applicable
Nut...............................Not applicable
User defined......................None
o European practices 1 (DIN)
100-199
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
British Standards
205 = 'default metric'
206 = 'default converted imperial'
691
Codelists
210 = 'plate flanges BS4504'
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
'35 pcf'
'57 pcf'
'88 pcf'
'97 pcf'
'111 pcf'
'150 pcf'
'165 pcf'
'260 pcf'
'450 pcf'
'450 pcf'
'450 pcf'
'490 pcf'
'490 pcf'
'525 pcf'
'555 pcf'
'570 pcf'
[Vitrified clay]
[Polypropylene]
[PVC]
[CPVC]
[FRP, Kynar]
[Reinforced concrete pipe]
[Aluminum]
[Titanium]
[Iron]
[Standard thk cement linin, ductile iron]
[Double thk cement lining ductile iron]
[Carbon steel, low Cr alloy steel, stainless steel]
[Cement lined carbon steel]
[Brass, Inconel]
[Bronze, copper, Monel, nickel]
[Hastelloy]
692
=
=
=
=
=
=
[Blank]
'Weight
'Weight
'Weight
'Weight
'Weight
selection
selection
selection
selection
selection
flag
flag
flag
flag
flag
1'
2'
3'
4'
5'
Codelists
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
'1'
'2'
'3'
'4'
'5'
'6'
'7'
'8'
'9'
'10'
'11'
'12'
'13'
'14'
'15'
'16'
'17'
'18'
'19'
'-'
'21'
'-'
'-'
'-'
'-'
'-'
'-'
'-'
'-'
'-'
'31'
'32'
'33'
'34'
'-'
'36'
'-'
'-'
'-'
693
Codelists
209
210
216
222
228
230
234
240
246
247
248
252
253
254
258
264
270
276
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
'561 km3'
'913 km3'
'1410 km3'
'1554 km3'
'1778 km3'
'2403 km3'
'2643 km3'
'4165 km3'
'7208 km3'
'7208 km3'
'7208 km3'
'7849 km3'
'7849 km3'
'7849 km3'
'7849 km3'
'8410 km3'
'8890 km3'
'9130 km3'
[polypropylene]
[pvc]
[cpvc]
[FRP, Kynar]
[Aluminium]
[Titanium]
[Iron]
[CS]
[low alloy st]
[SS]
[8mm thk cement lined CS]
[Brass, Inconel]
[Bronze, copper, Monel, Nickel]
[Hastelloy]
=
=
=
=
=
=
=
=
=
=
=
'General Fittings'
'Pipe Bends
'
'Orifice Flanges '
'Branch Nipples '
'Branch Reinforcement'
'Valves
'
'Piping
'
'Tubing
'
'Gaskets
'
'Bolts
'
'Nuts
'
=
=
=
=
'Specific - General
'Typical - General
'Specific - Valve
'Typical - Valve
'
'
'
'
694
specific instruments
typical instruments
specific valves
typical values
Codelists
300
350
400
450
=
=
=
=
'Specific - General
'Typical - General
'Specific - Valve
'Typical - Valve
'
'
'
'
695
Codelists
1064
1074
1100
1162
1201
1202
1203
1204
1205
1207
1208
1209
1310
1312
1410
1605
1610
1620
1630
1710
1720
1900
2000
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
'Pressure Units'
'Density Units'
'Weld Type'
'Force Units'
'Drawing Scale'
'Drawing Size'
'Interference Manager Approval Status'
'Interference Clash Type'
'Interference Manager Action'
'Interference Manager Approval Method'
'Clash Checking Option'
'Clash Checking Volume Filter Option'
'Report Source'
'Report Type'
'Design Review Type'
'Model Status'
'Force Units for FrameWorks Plus'
'Drawing View Direction'
'Drawing View Composition Status'
'Document Type'
'Document Sub-Type'
'Isometric Drawing Type'
'Orthographic Drawing Type'
696
Convert To First
Dest. Unit
m^2
A
0.0
Factor
9.290 304* E-02
cm^2
6.451 6*
E+00
0.0
m^2
8.361 274
E-01
0.0
km^2
2.589 988
E+00
0.0
mm^2
mm^2
1.0*
E+02
0.0
cm^2
1.0*
E+04
0.0
m^2
1.0*
E+06
0.0
---
---
0.0
-9999.
Codelists
Convert To
Dest. Unit
Factor
kg
4.535 924
E-01
0.0
mg
6.479 891
E+01
0.0
Mg
9.071 847
E-01
0.0
Mg
1.016 047
E+00
0.0
(Mu)g
0.0
mg
0.0
0.0
kg
0.0
Mg
0.0
---
---
-9999.
Dest. Unit
degC
Factor
(degF - 32)/1.8
A
0.0
degC
+3.2*
5/9
---
---
-9999.
B
1.0*
E+01 1.8*
697
Codelists
698
Codelists
=
=
=
=
=
=
=
[Blank]
'Pipe connector'
'Shop weld'
'Field weld at assembly site'
'Field weld at job site'
'Field weld at job site for loose flange'
'Field fit weld at job site'
=
=
=
=
=
=
=
=
=
=
'lbf'
'kipf'
'UStonf'
'UKtonf'
'dyn'
'mN'
'N'
'kgf'
'kN'
[Blank]
699
Codelists
700
=
=
=
=
=
=
=
=
'
'
'
'
'
'
'
'
Codelists
110
111
112
113
120
121
122
123
206
220
221
222
223
501
502
504
505
506
510
511
512
513
520
521
522
523
602
604
606
620
621
622
623
1001
1002
1004
1005
1006
1010
1012
1013
1020
1021
1022
1023
1101
1102
1104
1105
1106
1110
1111
1112
1113
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
Hard vs HardMaint'
Hard vs HardAccess'
Hard vs HardSafety'
Hard vs HardOperating'
Hard vs SoftMaint'
Hard vs SoftAccess'
Hard vs SoftSafety'
Hard vs SoftOperating'
Soft vs Insul'
Soft vs SoftMaint'
Soft vs SoftAccess'
Soft vs SoftSafety'
Soft vs SoftOperating'
Fproof vs Hard'
Fproof vs Soft'
Fproof vs CT'
Fproof vs Fproof'
Fproof vs Insul'
Fproof vs HardMain'
Fproof vs HardAccess'
Fproof vs HardSafety'
Fproof vs HardOperat'
Fproof vs HardMain'
Fproof vs HardAccess'
Fproof vs HardSafety'
Fproof vs HardOperat'
Insul vs Soft'
Insul vs CT'
Insul vs Insul'
Insul vs SoftMain'
Insul vs SoftAccess'
Insul vs SoftSafety'
Insul vs SoftOperat'
HardMain vs Hard'
HardMain vs Soft'
HardMain vs CT'
HardMain vs Fproof'
HardMain vs Insul'
HardMain vs HardMain'
HardMain vs HardSafety'
HardMain vs HardOperat'
HardMain vs SoftMain'
HardMain vs SoftAccess'
HardMain vs SoftSafety'
HardMain vs SoftOperat'
HardAcc vs Hard'
HardAcc vs Soft'
HardAcc vs CT'
HardAccess vs Fproof'
HardAccess vs Insul'
HardAcc vs HardMain'
HardAcc vs HardAcc'
HardAcc vs HardSafety'
HardAcc vs HardOperat'
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
701
Codelists
1120
1121
1122
1123
1201
1202
1204
1205
1206
1210
1211
1212
1213
1220
1221
1222
1223
1301
1302
1304
1305
1306
1310
1311
1312
1313
1320
1321
1322
1323
2002
2004
2006
2020
2021
2022
2023
2102
2104
2106
2120
2121
2122
2123
2202
2204
2206
2220
2221
2222
2223
2302
2304
2306
702
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
HardAcc vs SoftMain'
HardAcc vs SoftAcc'
HardAcc vs SoftSafety'
HardAcc vs SoftOperat'
HardSafety vs Hard'
HardSafety vs Soft'
HardSafety vs CT'
HardSafety vs Fproof'
HardSafety vs Insul'
HardSafety vs HardMain'
HardSafety vs HardAcc'
HardSafety vs HardSafety'
HardSafety vs HardOperat'
HardSafety vs SoftMain'
HardSafety vs SoftAccess'
HardSafety vs SoftSafety'
HardSafety vs SoftOperat'
HardOperat vs Hard'
HardOperat vs Soft'
HardOperat vs CT'
HardOperat vs Fproof'
HardOperat vs Insul'
HardOperat vs HardMain'
HardOperat vs HardAccess'
HardOperat vs HardSafety'
HardOperat vs HardOperat'
HardOperat vs SoftMain'
HardOperat vs SoftAccess'
HardOperat vs SoftSafety'
HardOperat vs SoftOperat'
SoftMain vs Soft'
SoftMain vs CT'
SoftMain vs Insul'
SoftMain vs SoftMain'
SoftMain vs SoftAccess'
SoftMain vs SoftSafety'
SoftMain vs SoftOperat'
SoftAccess vs Soft'
SoftAccess vs CT'
SoftAccess vs Insul'
SoftAccess vs SoftMain'
SoftAccess vs SoftAccess'
SoftAccess vs SoftSafety'
SoftAccess vs SoftOperat'
SoftSafety vs Soft'
SoftSafety vs CT'
SoftSafety vs Insul'
SoftSafety vs SoftMain'
SoftSafety vs SoftAccess'
SoftSafety vs SoftSafety'
SoftSafety vs SoftOperat'
SoftOperat vs Soft'
SoftOperat vs CT'
SoftOperat vs Insul'
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
;
Codelists
2320
2321
2322
2323
=
=
=
=
'
'
'
'
SoftOperat
SoftOperat
SoftOperat
SoftOperat
vs
vs
vs
vs
SoftMain'
SoftAccess'
SoftSafety'
SoftOperat'
;
;
;
;
=
=
=
=
=
=
=
=
'Unknown'
'Project Mode'
'Design Area Mode'
'Pre-defined Volume Mode'
=
=
=
=
=
=
=
'
'
'
'
'
'
'
MTO Report
Drawing Report
PID Report Header
Project Control Report
Clash Management Report
Piping Job Spec Report
Table Checker Report
'
'
'
'
'
'
'
703
Codelists
601
682
685
687
689
690
692
696
=
=
=
=
=
=
=
=
=
=
=
=
'Undefined'
'Preliminary'
'Temporary'
'Permanent'
704
=
=
=
=
'LBS'
'KIPS'
'N'
'kN'
Codelists
=
=
=
=
=
=
=
'Plan'
'East Elevation'
'North Elevation'
'Isometric'
'West Elevation'
'South Elevation'
'Plan (Vertical)'
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
705
Codelists
81
82
85
91
92
95
99
=
=
=
=
=
=
=
706
Codelists
(500-599) Civil/Structural Documents
501 = 'Civil/Structural RDB Reports | 51'
505 = 'Civil/Structural Job Specifications | 99'
511 = 'Civil/Structural Requisitions | 99'
531 = 'Site Preparation Drawings | 99'
535 = 'Foundation Location Drawings | 65'
537 = 'Piling Drawings | 65'
538 = 'Foundation Drawings | 55'
540 = 'Structural Perspectives, Plans, Sections and Details | 65'
545 = 'Concrete Structural Drawings | 55'
550 = 'Steel Structural Drawings | 55'
570 = 'Building Drawings | 99'
599 = 'Other Civil/Structural Documents | 99'
(600-699) Piping Documents
601 = 'Piping RDB Reports | 61'
602 = 'Piping Specialty RDB Reports | 46'
605 = 'Piping Job Specifications | 99'
611 = 'Piping Commodity Requisitions | 99'
612 = 'Piping Specialty Requisitions | 47'
631 = 'P&IDs | 15'
633 = 'Hydrotest P&IDs | 15'
641 = 'Plot Plans | 65'
643 = 'Equipment Arrangement Drawings | 65'
651 = 'Piping Underground Drawings | 65'
661 = 'Equipment Orientations | 65'
663 = 'Piping One Line Drawings | 65'
665 = 'Piping Perspectives, Plans, Sections and Details | 65'
667 = 'Pipeline Alignment Drawings | 65'
669 = 'Piping Isometric Drawings | 67'
671 = 'Piping Spool Drawings | 67'
673 = 'Spring Hanger Drawings | 99'
675 = 'Pipe Support Details | 99'
681 = 'P&ID Equipment List | 12'
682 = 'Equipment List | 62'
684 = 'P&ID Line List | 12'
685 = 'Piping Line List | 62'
687 = 'Piping Segments Report | 62'
689 = 'Piping Components MTO Report | 62'
690 = 'Pipe Supports Report | 62'
692 = 'Instrument List | 62'
696 = 'Piping Release Report | 62'
699 = 'Other Piping Documents | 99'
707
Codelists
(700-799) Instrument Documents
701 = 'Instrument RDB Reports | 71'
705 = 'Instrument Job Specifications | 99'
711 = 'Instrument Requisitions | 72'
721 = 'Instrument Logic Diagrams | 75'
723 = 'Instrument Loop Diagrams | 75'
731 = 'Instrument Location Plans | 65'
733 = 'Instrument Control House/Panel Drawings | 99'
735 = 'Instrument Hook Up Drawings | 75'
737 = 'Instrument Heat Tracing Drawings | 75'
739 = 'Instrument Wiring Drawings | 99'
771 = 'Instrument Index | 72'
799 = 'Other Instrument Documents | 99'
(800-899) Electrical Documents
801 = 'Electrical RDB Reports | 81'
805 = 'Electrical Job Specifications | 99'
811 = 'Electrical Requisitions | 99'
831 = 'Electrical One Line Diagrams | 99'
841 = 'Electrical Area Classification Drawings | 65'
851 = 'Electrical Underground Drawings | 65'
861 = 'Electrical Power Drawings | 99'
863 = 'Electrical Communications Drawings | 99'
865 = 'Lighting Perspectives, Plans, Sections and Details | 65'
867 = 'Electrical Heat Tracing Drawings | 99'
899 = 'Other Electrical Documents | 99'
(900-999) HVAC Documents
901 = 'HVAC RDB Reports | 91'
905 = 'HVAC Job Specifications | 99'
911 = 'HVAC Requisitions | 99'
931 = 'HVAC Flow Diagrams | 99'
971 = 'HVAC Perspectives, Plans, Sections and Details | 65'
999 = 'Other HVAC Documents | 99'
708
Codelists
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
'
'
'
'
'
'
'
'
'
'
'
'
'
'
'
709
Index
6
6P4C30, Wet sprinkler (on-line) 148
6P4C31, Pre-action sprinkler (on-line) 149
6P4C32, Spray sprinkler (on-line) 149
6P6C17, Spray nozzle (on-line) (PID piping
comp type 529) 169
6Q1C01, Gate valve (in-line) 50
6Q1C02, Extended body gate valve (in-line)
51
6Q1C03, Conduit gate valve (in-line) 52
6Q1C04, Blank gate valve (in-line) 52
6Q1C05, 3-way valve (in-line) 53
6Q1C06, [2-way] ball valve (in-line) 53
6Q1C08, 3-way ball valve (in-line) 54
6Q1C11, [2-way] globe valve (in-line) 55
6Q1C12, [2-way] angle globe valve (in-line)
56
6Q1C13, 3-way globe valve (in-line) 57
6Q1C14, Y globe valve (in-line) 57
6Q1C16, [2-way] plug valve (in-line) 58
6Q1C18, 3-way plug valve (in-line) 60
6Q1C19, 4-way plug valve (in-line) 60
6Q1C22, Needle valve (in-line) 60
6Q1C26, Butterfly valve (in-line) 60
6Q1C30, Diaphragm valve (in-line) 61
6Q1C32, Knife gate valve (in-line) 62
6Q1C33, [2-way] slide valve (in-line) 62
6Q1C34, 3-way slide valve (in-line) 63
6Q1C37, Angle valve (in-line) 64
6Q1C38, Check valve (in-line) (directional)
64
6Q1C39, Wafer check valve (in-line)
(directional) 67
6Q1C40, Angle check valve (in-line)
(directional) 67
6Q1C41, Stop check valve (in-line)
(directional) 68
6Q1C42, Angle stop check valve (in-line)
(directional) 68
6Q1C43, Y stop check valve (in-line)
(directional) 68
6Q1C50, Backflow preventer (in-line)
(directional) 69
6Q1C51, Automatic recirculation valve
(in-line) (directional) 69
6Q1C53, Angle blowdown valve (in-line) 69
6Q1C54, Y blowdown valve (in-line) 70
6Q1C56, Pinch valve (in-line) 70
711
Index
6Q2C28, Eccentric reducer (in-line)
(not-automatic) 92
6Q2C32, Reducing coupling (in-line)
(not-automatic) 92
6Q2C35, Concentric swage (in-line) 93
6Q2C36, Eccentric swage (in-line)
(not-automatic) 93
6Q2C39, Union (in-line) (not-automatic) 94
6Q2C40, Orifice union (in-line)
(not-automatic) 94
6Q2C41, Dielectric union (in-line)
(not-automatic) 94
6Q2C43, Hose connection (in-line)
(not-automatic) 94
6Q2C44, Bushing (in-line) (not-automatic)
95
6Q2C46, Reducing insert (in-line)
(not-automatic) 95
6Q2C47, Pipe bend (in-line) 95
6Q2C49, 5.625 deg elbow (in-line)
(not-automatic) 96
6Q2C51, 11.25 deg elbow (in-line)
(not-automatic) 96
6Q2C53, 22.5 deg elbow (in-line)
(not-automatic) 97
6Q2C55, <45 deg direction change (in-line)
97
6Q2C56, 45 deg direction change (in-line)
98
6Q2C57, 45 deg elbow (in-line) 98
6Q2C59, 45 deg LR elbow (in-line) 99
6Q2C60, 45 deg long tangent elbow (in-line)
99
6Q2C61, 45 deg 3D elbow (in-line) 100
6Q2C63, 45 deg union elbow (in-line)
(not-automatic) 100
6Q2C65, 45 deg street elbow (in-line)
(not-automatic) 100
6Q2C66, 45 deg short elbow (in-line) 101
6Q2C68, 45 deg long elbow (in-line) 101
6Q2C73, 60 deg elbow (in-line)
(not-automatic) 101
6Q2C75, 45-90 deg direction change
(in-line) 101
6Q2C76, 90 deg direction change (in-line)
102
6Q2C77, 90 deg elbow (in-line) 102
6Q2C79, 90 deg SR elbow (in-line) 103
6Q2C80, 90 deg LR elbow (in-line) 103
6Q2C82, 90 deg LR long tangent elbow
(in-line) 104
6Q2C84, 90 deg reducing elbow (in-line)
104
712
Index
6Q3C55, 90 deg reducing long Y-branch
(in-line) (not-automatic) 124
6Q3C60, Cross (in-line) (not-automatic)
124
6Q3C62, Reducing branches cross (in-line)
(not-automatic) 125
6Q3C63, Reducing run and branches cross
(in-line) (not-automatic) 125
6Q3C64, Basin cross (in-line)
(not-automatic) 126
6Q3C70, Saddle (in-line) 126
6Q3C72, Sweepolet (in-line) 126
6Q3C73, Weldolet (in-line) 127
6Q3C74, Sockolet (in-line) 127
6Q3C75, Thredolet (in-line) 128
6Q3C76, Nippolet (in-line) 128
6Q3C77, Elbolet (in-line) (not-automatic)
129
6Q3C78, Latrolet (in-line) (not-automatic)
129
6Q3C79, Endolet (in-line) (not-automatic)
130
6Q3C80, Reinforcing pad (in-line) 130
6Q3C82, Reinforcing weld (in-line) 132
6Q3C83, Non-radial Reinforcing Weld 229
6Q3C84, Buttweld (in-line) (not-automatic)
134
6Q3C86, Full Encirclement Reinforcement
Pad (In-Line) 134
6Q3C88, Branch nipple (in-line)
(not-automatic) 134
6Q3C89, In-line nipple (in-line)
(not-automatic) 135
6Q3C95, Gasket 135
6Q3C97, Stud 137
6Q4C01, Fire monitor (in-line) 145
6Q4C02, Elevated fire monitor (in-line) 145
6Q4C03, Remotely operated fire monitor
(in-line) 145
6Q4C04, Foam monitor (in-line) 146
6Q4C05 Elevated foam monitor (in-line)
146
6Q4C06, Remotely operated foam monitor
(in-line) 146
6Q4C10, [2-way] fire hydrant (in-line) 147
6Q4C11, [2-way] fire hydrant w/monitor
nozzle (in-line) 147
6Q4C13, 3-way fire hydrant (in-line) 147
6Q4C24, Hose reel (in-line) 148
6Q4C25, Hose rack station (in-line) 148
6Q4C26, Foam chamber (in-line) 148
6Q4C38, Eye wash (in-line) 149
6Q4C39, Safety shower (in-line) 149
713
Index
6Q5P27, Instrument tee (in-line)
(not-automatic) 155
6Q5P28, Short outlet run tee (in-line)
(not-automatic) 155
6Q5P31, Cross (in-line) (not-automatic)
156
6Q5P32, Reducing cross (in-line)
(not-automatic) 156
6Q5P33, Cross (in-line) (not-automatic)
156
6Q5P35, Tee (in-line) (not-automatic) 156
6Q5P36, Reducing tee (in-line)
(not-automatic) 156
6Q5P37, Short outlet tee (in-line)
(not-automatic) 157
6Q5P38, Short outlet reducing tee (in-line)
(not-automatic) 157
6Q5P39, Instrument tee (in-line)
(not-automatic) 157
6Q5P41, Concentric reducer (in-line)
(not-automatic) 157
6Q5P42, Concentric reducer (in-line)
(not-automatic) 157
6Q5P43, Concentric reducer (in-line)
(not-automatic) 158
6Q5P45, Eccentric reducer (in-line)
(not-automatic) 158
6Q5P46, Eccentric reducer (in-line)
(not-automatic) 158
6Q5P47, Eccentric reducer (in-line)
(not-automatic) 158
6Q5P51, Clamp, adjustable (in-line)
(not-automatic) 158
6Q5P52, Clamp, heavy duty (in-line)
(not-automatic) 159
6Q5P53, Clamp, 3 piece heavy duty (in-line)
(not-automatic) 159
6Q5P54, Clamp, pressure adjustable
(in-line) (not-automatic) 159
6Q5P55, Clamp, high pressure (in-line)
(not-automatic) 159
6Q5P56, Clamp, assembly (in-line)
(not-automatic) 159
6Q5P57, Clamp, swivel joint (in-line)
(not-automatic) 160
6Q5P58, Clamp, 2 piece heavy duty (in-line)
(not-automatic) 160
6Q5P60, 2-way diaphragm valve (in-line)
(not-automatic) 160
6Q5P61, 2-way diaphragm valve (in-line)
(not-automatic) 160
6Q5P62, Zero deadleg T valve (in-line)
(not-automatic) 161
714
Index
6Q6C40, Sample cooler (in-line) (PID
piping comp type 552) 172
6Q6C45, Single basket strainer (in-line)
(PID piping comp type 557) 172
6Q6C47, Duplex basket strainer (in-line
with operator) (PID piping comp type
559) 172
6Q6C49, T strainer (in-line) (PID piping
comp type 561) 172
6Q6C51, Y strainer (in-line) (PID piping
comp type 563) 173
6Q6C52, Temporary strainer (in-line) (PID
piping comp type 564) 173
6Q6C53, Basket strainer (in-line) (PID
piping comp type 565) 173
6Q6C55, Cone strainer (in-line) (PID piping
comp type 567) 174
6Q6C57, Flat plate strainer (in-line) (PID
piping comp type 569) 174
6Q6C59, Sump strainer (in-line) (PID
piping comp type 571) 174
6Q6C64, Filter (in-line) (PID piping comp
type 576) 174
6Q6C70, Steam trap (in-line) (PID piping
comp type 582) 174
6Q6C71, Float steam trap (in-line) (PID
piping comp type 583) 174
6Q6C72, Inverted bucket steam trap
(in-line) (PID piping comp type 584) 174
6Q6C74, Thermostatic steam trap (in-line)
(PID piping comp type 586) 174
6Q6C76, Thermodynamic steam trap
(in-line) (PID piping comp type 588) 174
6Q6C78, Impulse steam trap (in-line) (PID
piping comp type 590) 174
6Q6C99, Generic component (in-line) (PID
piping comp type 611) 175
7
7P1E01, [2-way generic body] control valve
(in-line) 181
7P1E02, [2-way generic body] angle control
valve (in-line) 181
7P1E03, 3-way [generic body] control valve
(in-line) 181
7P1E04, 4-way [generic body] control valve
(in-line) 181
7P1E05, [2-way] angle globe control valve
(in-line) 181
7P1E06, 3-way globe control valve (in-line)
181
7P1E07, [2-way] solenoid valve (in-line)
181
715
Index
7P2C01, Angle press relief valve (in-line)
190
7P2C06, Straight-thru press relief valve
(in-line) 190
7P2C09, Vac relief valve (in-line) 190
7P2C12, Press/vac relief valve (in-line) 191
7P2C14, Press/vac relief manhole cover
(in-line) 191
7P2C16, Press relief rupture disc (in-line)
191
7P2C18, Vac relief rupture disc (in-line)
191
7P2C20, Temp fusible plug or disc (in-line)
191
7P3C01, Balloon instr (in-line) 196
7P3C02, Restriction orif union (in-line) 196
7P3C03, Valve w/restriction orif (in-line)
196
7P3C04, Orif plate (in-line) 196
7P3C05, Orif plate & flanges (in-line) 196
7P3C06, Orif plate, flanges & meter run
(in-line) 197
7P3C09, Orif plate & qk chnge fitting (in-line)
197
7P3C10, Orif pl, qk chnge fitting & met run
(in-line) 197
7P3C13, Venturi tube (in-line) 197
7P3C16, In-line averaging pitot tube (in-line)
197
7P3C19, Flow nozzle (in-line) 197
7P3C22, Var area flow instr (in-line) 198
7P3C23, Var area flow instr w/upstr reg
(in-line) 198
7P3C24, Var area flow instr w/dwnstr reg
(in-line) 198
7P3C25, Var area flow instr w/upstr vlv
(in-line) 198
7P3C26, Var area flow instr w/dwnstr vlv
(in-line) 198
7P3C29, Pos displacement flow instr
(in-line) 198
7P3C30, Pos displ flow instr w/dwnstr reg
(in-line) 199
7P3C33, In-line target flow instr (in-line)
199
7P3C35, In-line propeller flow instr (in-line)
199
7P3C37, Vortex flow instr (in-line) 199
7P3C39, In-line magnetic flow instr (in-line)
199
7P3C41, In-line ultrasonic flow instr (in-line)
199
7P3C44, Flume (in-line) 200
716
Index
7Q4D28, Discrete [field mounted] LSL
(off-line) 210
7Q4D29, Discrete [field mounted] LSM
(off-line) 210
7Q4D30, Discrete [field mounted] LSHH
(off-line) 211
7Q4D31, Discrete [field mounted] LSHL
(off-line) 211
7Q4D32, Discrete [field mounted] LSLL
(off-line) 211
7Q4D33, Discrete [field mounted] LT
(off-line) 211
7Q4D35, Discrete [field mounted] PC
(off-line) 212
7Q4D36, Discrete [field mounted] PDIC
(off-line) 212
7Q4D37, Discrete [field mounted] PDSH
(off-line) 212
7Q4D38, Discrete [field mounted] PDSL
(off-line) 212
7Q4D39, Discrete [field mounted] PDT
(off-line) 212
7Q4D40, Discrete [field mounted] PI
(off-line) 212
7Q4D41, Discrete [field mounted] PIC
(off-line) 213
7Q4D42, Discrete [field mounted] PP
(off-line) 213
7Q4D43, Discrete [field mounted] PR
(off-line) 213
7Q4D44, Discrete [field mounted] PRC
(off-line) 213
7Q4D45, Discrete [field mounted] PSH
(off-line) 213
7Q4D46, Discrete [field mounted] PSL
(off-line) 213
7Q4D47, Discrete [field mounted] PSM
(off-line) 214
7Q4D48, Discrete [field mounted] PSHH
(off-line) 214
7Q4D49, Discrete [field mounted] PSHL
(off-line) 214
7Q4D50, Discrete [field mounted] PSLL
(off-line) 214
7Q4D51, Discrete [field mounted] PT
(off-line) 214
7Q4D53, [Field mounted] pilot light (off-line)
214
7Q4D57, Discrete single-funct, [field
mounted] instr (off-line) 215
7Q4D58, Discrete multi-funct, [field
mounted] instr (off-line) 215
A
Assemblies 230
Assembly Notes 432
B
Basic Information 39
Bio-Pharm Operator Symbol SOP_3 401
Bio-Pharm Operator Symbol SOP_42 402
Bio-Pharm Specialty Component Symbol
R180B 403
Bio-Pharm Specialty Component Symbol
R180S 404
717
Index
Bio-Pharm Specialty Component Symbol
VS3WD 406
Bio-Pharm Specialty Component Symbol
VS4WD 407
Bio-Pharm Specialty Component Symbol
VSCCB 405
Bio-Pharm Specialty Component Symbol
VSCCBU425 405
Bio-Pharm Specialty Component Symbol
VSDTC 405
Bio-Pharm Specialty Component Symbol
VSDTP 404
Bio-Pharm Specification Component
Symbol B45C 380
Bio-Pharm Specification Component
Symbol B45T 379
Bio-Pharm Specification Component
Symbol B45TC 379
Bio-Pharm Specification Component
Symbol B90C 378
Bio-Pharm Specification Component
Symbol B90T 376
Bio-Pharm Specification Component
Symbol B90TC 377
Bio-Pharm Specification Component
Symbol C2HD 397
Bio-Pharm Specification Component
Symbol C3HD 397
Bio-Pharm Specification Component
Symbol CA 398
Bio-Pharm Specification Component
Symbol CAPSE 373
Bio-Pharm Specification Component
Symbol CAPT 372
Bio-Pharm Specification Component
Symbol CHA 396
Bio-Pharm Specification Component
Symbol CHD 399
Bio-Pharm Specification Component
Symbol CPAN 397
Bio-Pharm Specification Component
Symbol CPHB 398
Bio-Pharm Specification Component
Symbol CSJ 398
Bio-Pharm Specification Component
Symbol FA 374
Bio-Pharm Specification Component
Symbol FAS 374
Bio-Pharm Specification Component
Symbol FERR 371
Bio-Pharm Specification Component
Symbol FERS 372
718
Index
Bio-Pharm Specification Component
Symbol XT 387
Bio-Pharm Specification Component
Symbol XTRB 388
Bio-Pharmaceutical Operators 160, 401
Bio-Pharmaceutical Specialty Components
161, 403
Bio-Pharmaceutical Specification
Components 150
Bio-Pharmaceutical
SpecificationComponent Symbols 371
Bolting 566
C
Calculations From ANSI-B31.1 and
ANSI-B31.3 573
CL1010, Area Units (25) 696
CL1028, Mass Units (40) 697
CL1056, Temperature Units (15) 697
CL1064, Pressure Units (40) 698
CL1074, Density Units (35) 699
CL1100, Weld Type (100) 699
CL1162, Force Units (40) 699
CL1201, Drawing Scale (540) 700
CL1202, Drawing Size (199) 700
CL1203, Interference Manager Approval
Status (99) 700
CL1204, Interference Clash Type 700
CL1205, Interference Manager Action (10)
703
CL1207, Interference Manager Approval
Method (10) 703
CL1208, Clash Checking Option 703
CL1209, Clash Checking Volume Filter
Option 703
CL125, Fluid Code/Connector Type (999)
585
CL130, Construction Status (15) 589
CL1310, Report Source (99) 703
CL1312, Report Type (999) 703
CL1410, Design Review Type (10) 704
CL145, Materials Grade (4500) 589
CL148, Piping Materials Class Description
(31999) 625
CL160, Responsibility (25) 636
CL1605, Model Status 704
CL1610, Force Units for FrameWorks Plus
(40) 704
CL1620, Drawing View Directions (7) 705
CL1630, Drawing View Composition Status
(4) 705
CL1710, Document Source (99) 705
CL1720, Document Type (999) 706
719
Index
Commodity Code Descriptions 435
Commodity Code Matrix 435
Commodity Discussions 39
Completing Materials 441
Connect Point Data 44, 141, 165, 178, 187,
193, 203
Connect Point Data_GCP 75
Connect Point Data_Independent Variables
107
Control Valves and Regulators (7P1E) 176
D
Definition of Generic Variables 35
Definition of Specific Variables 32
Design DDL 20
Detail F1 413
Detail F2 413
Detail F4 414
Detail F7 414
Detail F8 415
Detail H1 411
Detail H2 411
Detail H3 412
Detail H4 412
Detail L1 421
Detail L2 421
Detail L4 422
Detail L7 423
Detail L8 424
Detail P1 415
Detail P2 416
Detail P3 416
Detail P4 417
Detail P5 417
Detail P7 418
Detail P8 418
Detail P9 419
Detail T 420
Detail T1 419
Detail T4 420
Detail V1 407
Detail V2 408
Detail V3 408
Detail V4 409
Detail V5 409
Detail V7 410
Detail V8 410
Details Assumed 407
F
Fire and Safety Components 442
720
G
Gaskets 559
General Comments 579
General Conventions 23
I
In-Line Bio-Pharmaceutical Components
(6Q5P) 150
In-line Piping Macrocomponents (6N8C)
230
Instrument Specialties 465
Instrument Specialty Discussions 175
Instrument Specialty Symbol I106BZ 340
Instrument Specialty Symbol I109BZ 341
Instrument Specialty Symbol I118BZ 341
Instrument Specialty Symbol I11AZ 335
Instrument Specialty Symbol I120AZ 342
Instrument Specialty Symbol I12AZ 336
Instrument Specialty Symbol I13AZ 336
Instrument Specialty Symbol I14AZ 337
Instrument Specialty Symbol I15AZ 337
Instrument Specialty Symbol I16AZ 338
Instrument Specialty Symbol I17AZ 338
Instrument Specialty Symbol I18AZ 339
Index
Instrument Specialty Symbol I201AZ 342
Instrument Specialty Symbol I201BZ 343
Instrument Specialty Symbol I201CZ 343
Instrument Specialty Symbol I209AZ 344
Instrument Specialty Symbol I20AZ 339
Instrument Specialty Symbol I213AZ 344
Instrument Specialty Symbol I216AZ 345
Instrument Specialty Symbol I219AZ 345
Instrument Specialty Symbol I237AZ 346
Instrument Specialty Symbol I253AZ 346
Instrument Specialty Symbol I301AZ 347
Instrument Specialty Symbol I30AZ 340
Instrument Specialty Symbol I324CZ 347
Instrument Specialty Symbol I324DZ 348
Instrument Specialty Symbol I324EZ 348
Instrument Specialty Symbol I324FZ 349
Instrument Specialty Symbol I3AZ 333
Instrument Specialty Symbol I5AZ 333
Instrument Specialty Symbol I6AZ 334
Instrument Specialty Symbol I7AZ 334
Instrument Specialty Symbol I8AZ 335
Instrument Specialty Symbols 333
Introduction 17
L
Labor Codes 488
M
Miscellaneous 218
Miscellaneous Non-Wetted Fittings 497
Miscellaneous Symbol A1003 368
Miscellaneous Symbol A1005 368
Miscellaneous Symbol A1251 369
Miscellaneous Symbol A1331 369
Miscellaneous Symbol A1332 370
Miscellaneous Symbol OP_251 351
Miscellaneous Symbol OP_271 352
Miscellaneous Symbol OP_291 352
Miscellaneous Symbol OP_292 353
Miscellaneous Symbol OP_311 353
Miscellaneous Symbol OP_331 354
Miscellaneous Symbol OP_332 354
Miscellaneous Symbol OP_333 355
Miscellaneous Symbol OP_334 355
Miscellaneous Symbol OP_351 356
Miscellaneous Symbol OP_391 356
Miscellaneous Symbol OP_401 357
Miscellaneous Symbol OP_411 357
Miscellaneous Symbol OP_412 358
Miscellaneous Symbol OP_413 358
Miscellaneous Symbol OP_451 359
Miscellaneous Symbol OP_452 359
N
Named and Unamed Specialties 165
Named and Unnamed Instruments 177
Named or Unnamed Instruments 192, 203
Named or Unnamed Relief Devices 187
Non-Database Part of Item Descriptions 19
Non-Database Part of the Piping Job
Specification 18
Non-parametric and Parametric Piping and
Tubing (PIPING, TUBING) 40
O
Off-Line Instruments (7Q4D) 201
Off-Site Piping Connectors (6R9H) 229
Off-volume Piping Connectors (6R9G) 228
On-line Fittings (6P2C) and In-line Fittings
(6Q2C) 74
On-line Fittings (6P3C) and In-line Fittings
(6Q3C) 106
On-line Piping Macrocomponents (6P8C)
230
Other in-line Instruments (7P3C) 191
P
Pipe 504
721
Index
Pipe Supports 475
Piping and Instrument Symbol Notes 425
Piping Commodity Data 39
Piping Commodity Symbol F10_1 264
Piping Commodity Symbol F10_2 265
Piping Commodity Symbol F101 283
Piping Commodity Symbol F114A 284
Piping Commodity Symbol F114B 285
Piping Commodity Symbol F114C 286
Piping Commodity Symbol F114D 287
Piping Commodity Symbol F122_1 288
Piping Commodity Symbol F122_2 289
Piping Commodity Symbol F125 290
Piping Commodity Symbol F127 291
Piping Commodity Symbol F128 292
Piping Commodity Symbol F13 266
Piping Commodity Symbol F134 293
Piping Commodity Symbol F145 294
Piping Commodity Symbol F147 295
Piping Commodity Symbol F14A 267
Piping Commodity Symbol F14B 268
Piping Commodity Symbol F150 296
Piping Commodity Symbol F152 297
Piping Commodity Symbol F154 298
Piping Commodity Symbol F160 299
Piping Commodity Symbol F163 300
Piping Commodity Symbol F170 301
Piping Commodity Symbol F172 302
Piping Commodity Symbol F173 303
Piping Commodity Symbol F176 304
Piping Commodity Symbol F177 305
Piping Commodity Symbol F178 307
Piping Commodity Symbol F179 308
Piping Commodity Symbol F17D 269
Piping Commodity Symbol F180 309
Piping Commodity Symbol F180F 306
Piping Commodity Symbol F182 310
Piping Commodity Symbol F184 311
Piping Commodity Symbol F188 312
Piping Commodity Symbol F19 270
Piping Commodity Symbol F1A 260
Piping Commodity Symbol F25 271
Piping Commodity Symbol F27 272
Piping Commodity Symbol F28 273
Piping Commodity Symbol F31 274
Piping Commodity Symbol F32 275
Piping Commodity Symbol F39 276
Piping Commodity Symbol F4 261
Piping Commodity Symbol F43_1 277
Piping Commodity Symbol F43_2 278
Piping Commodity Symbol F47 279
Piping Commodity Symbol F47A 280
Piping Commodity Symbol F6 262
722
Index
Piping Specialty Symbol S64BC 331
Piping Specialty Symbol S70AC 331
Piping Specialty Symbol S70BC 332
Piping Specialty Symbol S78AC 332
Piping Specialty Symbol S7AZ 326
Piping Specialty Symbols 323
Piping Utility Connector (6R9E) 228
Preface PDS 15
R
Reference Data File Descriptions 17
Relief Devices (7P2C) 186
S
Seed File Definitions 20
Signal Lines (7N2A) 176
Socket Fittings 516
Socketwelded Fittings 524
SOP3, Manual bonnet (in-line)
(not-automatic) 160
SOP42, Pneumatic bonnet (in-line)
(not-automatic) 161
Steam Specialties 443
Strainer Specialties 459
Symbols 231
T
Threaded Fittings 527
Tubing and Hose 499
Tubing Fittings 518
U
Underground Fittings 532
V
Valve Operators and Actuators 219
Valves 535
Valves (6Q1C) 43
Variables Used in Symbols and Tables 32
W
Welded Fittings 551
723