Professional Documents
Culture Documents
..
.
..
.
..
.
OUTPUT CURRENTS UP TO 1A
FIXED PRECISION OUTPUT 1 VOLTAGE
5.1V +/- 2%
FIXED PRECISION OUTPUT 2 VOLTAGE
12V +/- 2%
OUTPUT 1 WITH RESET FACILITY
OUTPUT 2 WITH DISABLE BY TTL INPUT
SHORT CIRCUIT PROTECTION AT BOTH
OUTPUTS
THERMAL PROTECTION
LOW DROP OUTPUT VOLTAGE
AVAILABLE ALSO IN HEPTAWATT PACKAGE
IN TWO VERSIONS : TDA8138A (DISABLE
ONLY), TDA8138B (RESET ONLY)
DESCRIPTION
The TDA8138 is a monolithic dual positive voltage
regulator designed to provide fixed precision output
voltages of 5.1V and 12V at currents up to 1A.
An internal reset circuit generates a reset pulse
when the output 1 decrease below the regulated
voltage value (for TDA8138 and TDA8138B).
Output 2 can be disabled by TTL input (for
TDA8138 and TDA8138A).
Short circuit and thermal protections are included
in all the versions.
SIP9
(Plastic Package)
ORDER CODE : TDA8138
HEPTAWAT
(Plastic Package)
ORDER CODE : TDA8138A / TDA8138B
PIN CONNECTIONS
9
8
OUTPUT 1
OUTPUT 2
7
6
N.C.
OUTPUT1
OUTPUT2
N.C. FOR TDA8138A
RESET FOR TDA8138B
GROUND
DISABLEFOR TDA8138A
DEL. CAPA FOR TDA8138B
RESET
GROUND
DISABLE
3
2
DEL. CAP.
INPUT 2
INPUT 2
INPUT 1
INPUT 1
May 1993
HEPTAWATT
8138-01A.EPS - 8138-01B.EPS
SIP9
1/6
TDA8138
BLOCK DIAGRAM (SIP9 package)
IN 1
IN 2
REFERENCE
OUT 1
PROTECTION
OUT 1
RESET
RESET
3
DELAY
CAPACITOR
DISABLE
DISABLE
OUT 2
OUT 2
TDA8138
8138-02.EPS
Symbol
Value
Unit
VIN
20
VDIS
20
VRST
20
IO1, 2
Output Currents
Internally Limited
Power Dissipation
Internally Limited
Pt
Parameter
Tstg
Storage Temperature
-65 to +150
Tj
Junction Temperature
0 to +150
C
C
8138-01.TBL
Symbol
Rth (j-c)
Rth (j-a)
Tj
2/6
Parameter
Maximum Thermal Resistance Junction-case for SIP9
Maximum Thermal Resistance Junction-case for Heptawatt
Value
Unit
8
3
o
C/W
o
60
130
C/W
C/W
o
8138-02.TBL
THERMAL DATA
TDA8138
ELECTRICAL CHRACTERISTICS (VIN1 = 7V, VIN2 = 14V, Tj = 25oC, unless otherwise specified)
Symbol
Min.
Typ.
Max.
Unit
VO1
Output Voltage
IO1 = 10mA
5.1
5.2
VO2
Output Voltage
IO2 = 10mA
11.76
12
VO1
Output Voltage
VO2
Output Voltage
VIO1,2
Dropout Voltage
VO1,2LI
VO1,2LO
VO1RST
Test Conditions
12.24
4.9
5.3
11.5
12.5
IO1,2 = 750mA
IO1,2 = 1A
1.4
2
V
V
Line Regulation
50
120
mV
mV
Load Regulation
100
250
mV
mV
Quiescent Current
IO1 = 10mA
Output 2 Disabled
mA
K = VO1
K0.25
K - 0.1
50
75
mV
K - 0.4
tRD
Ce = 100nF
See circuit description
VRL
I5 = 5mA
0.4
IRH
V5 = 10V
10
KO1,2
Tj = 0 to 125oC
VO 106
KO =
T VO
IO1,2SC
VDISH
VDISL
VRTH
IDIS
Tjsd
20
25
ms
ppm/oC
100
1.6
1
2
A
A
V
-100
145
0.8
8138-03.TBL
IQ
Parameter
Note : Safe permanent short-circuit is only guaranteed for input voltages up to 16V.
CIRCUIT DESCRIPTION
The TDA8138 is a dual voltage regulator with Reset
and Disable (TD8138A : Disable only, TDA8138B :
Reset only).
The two regulation parts are supplied from one
voltage reference circuit trimmed by zener zap
during EWS test.
Since the supply voltage of this last is connected at
Pin 1 (VIN1), the regulator 2 will not work if Pin 1 is
not supplied.
The outputs stage have been realized in darlington
configuration with a drop typical 1.2V.
The disable circuit, switch-off the output 2 if a
voltage lower than 0.8V is applied at Pin 3
3/6
TDA8138
Figure 1
10A
REF
2.5V
+
-
OUT 1 9
50
RESET
6
REG
Ce
8138-03.EPS
2.5V 0.6V
Figure 2
5.1V
Vout LOW
4.9V
4.85V
TD
TD
8138-04.EPS
RESET
Ce
6
V IN1
V O1
V O2
TDA8138
C1
C2
C3
DISABLE
C1 to C4 = 10 F
4/6
C4
8138-05.EPS
V IN2
TDA8138
PACKAGE MECHANICAL DATA
9 PINS - PLASTIC HEPTAWATT
E
D1
M1
L1
L5
L2
G2
G1
H3
L3
PM-HEPTV.EPS
L7
H2
F1
Dia.
L6
A
C
D
D1
E
F
F1
G
G1
G2
H2
H3
L
L1
L2
L3
L5
L6
L7
M
M1
Dia.
Min.
Millimeters
Typ.
2.4
1.2
0.35
0.6
2.41
4.91
7.49
2.54
5.08
7.62
10.05
Max.
4.8
1.37
2.8
1.35
0.55
08
0.9
2.67
5.21
7.8
10.4
10.4
Min.
0.094
0.047
0.014
0.024
0.095
0.193
0.295
Max.
0.189
0.054
0.110
0.053
0.022
0.031
0.035
0.105
0.205
0.307
0.409
0.409
0.668
0.587
0.848
0.891
3
15.8
6.6
0.102
0.594
0.236
2.8
5.08
3.65
0.100
0.200
0.300
0.396
16.97
14.92
21.54
22.62
2.6
15.1
6
Inches
Typ.
0.118
0.622
0.260
0.110
0.200
3.85
0.144
HEPTV.TBL
Dimensions
0.152
5/6
TDA8138
PACKAGE MECHANICAL DATA
9 PINS - PLASTIC SIP
C
L3
L1
c2
d1
a1
L2
b1
e3
c1
PM-SIP9.EPS
b3
B
A
a1
B
b1
b3
C
c1
c2
D
d1
e
e3
L
L1
L2
L3
M
Min.
Millimeters
Typ.
2.7
Max.
7.1
3
24.8
Min.
0.106
0.5
0.85
Inches
Typ.
Max.
0.280
0.118
0.976
0.020
1.6
0.033
3.3
0.43
1.32
0.063
0.130
0.017
0.052
21.2
0.835
14.5
2.54
20.32
0.571
0.100
0.800
3.1
0.122
3
17.6
0.118
0.693
0.25
3.2
0.010
0.126
Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsibility
for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result
from its use. No licence is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics.
Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all
information previously supplied. SGS-THOMSON Microelectronics products are not authorized for use as critical components in life
support devices or systems without express written approval of SGS-THOMSON Microelectronics.
1994 SGS-THOMSON Microelectronics - All Rights Reserved
Purchase of I2C Components of SGS-THOMSON Microelectronics, conveys a license under the Philips
I2C Patent. Rights to use these components in a I2C system, is granted provided that the system conforms to
the I2C Standard Specifications as defined by Philips.
SGS-THOMSON Microelectronics GROUP OF COMPANIES
Australia - Brazil - China - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco
The Netherlands - Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A.
6/6
SIP9.TBL
Dimensions