Professional Documents
Culture Documents
V
Knife gate valves for pulp, reject and waste
Pressure classes
Maximum working pressure body at 20C
DN
MP
MV
XV
HL
HG
JT
DN
MP
MV
XV
HL
HG
50
16
50
16
JT
-
65
16
65
16
80
16
16
10
10
80
16
10
10
10
100
16
16
10
10
10
10
100
16
10
10
10
6,2
10
125
16
16
10
10
10
125
16
10
10
10
10
150
10
16
10
10
10
10
150
10
10
10
10
6,2
10
200
10
10
10
10
10
10
200
10
10
10
10
6,2
10
250
10
10
10
10
10
10
250
10
10
10
10
6,2
10
300
10
10
10
10
10
10
300
10
10
10
10
6,2
10
350
10
10
10
10
10
350
10
10
10
6,2
10
400
10
10
10
10
10
400
10
10
6,2
10
450
10
OR
10
10
10
450
OR
10
10
6,2
500
10
10
10
500
10
10
600
10
10
10
600
10
10
700
10
OR
OR
700
10
OR
OR
800
10
OR
OR
OR
800
10
OR
OR
OR
900
OR
OR
OR
OR
OR
OR
OR
900
OR
OR
OR
OR
OR
OR
OR
> 1000
OR
OR
OR
OR
OR
OR
OR
OR
OR
> 1000
OR
OR
OR
OR
OR
OR
OR
OR
OR
MP
DN 350 - DN 800
In 1928 our knife gate valve manufacturing started in close co-operation
with nearby pulp and paper mills. Now it is time for the eighth knife gate
valve generation, the MP, which is an assembled result of market driven
requirements and experienced engineering throughout the years.
The MP is a bi-directional valve in stainless steel with a preferred
pressure direction. It has a one piece body design. Just like MV this is
an all-round valve a Multi Purpose valve to be used in different types
of applications and the MPs sealing capacity further extends its eld of
applications.
MP features
The gate has a bevel edge that effectively cuts through the pulp. This
process is facilitated by the inner cavity of the valve body. In closed
position the gate is pushed against the seat which gives a secure sealing
and on the opposite side the gate support is positioned to create a bidirectional sealing.
The top work consists of aluminum beams and stainless steel tie rods
which gives good corrosion resistance and stability at manoeuvring. All
remote operated valves are supplied with gate guards in stainless steel.
The gland box is optimized with three layers of our TwinPackTM and a
box bottom scraper to give a tight sealing and to assure high operation
reliability. The gland box is also machined for maximum nish and thight
tolerances.
The valve has guiding pads in order to support and guide the gate from
DN 450.
For operation reliability in applications with corrosive or clogging media
the valve comes with integrated purge ports as standard.
The valve is equipped with gate support for bi-directional sealing. This
support is available in different material in order to customize it to
specic process conditions. The inner cavity of the body also contains
gate support cams.
MP is supplied with the retainer ring which can be combined with several
seat materials. It also offers smooth and cost-efcient maintenance.
MV
DN 50 - DN 1400
This is a true allround valve used in many types of applications. It is
modular designed and it can easilly be customized.
It comes in either one or a two piece valve body depending on valve
size. As standard MV is supplied in stainless steel or nodular iron, but it
can also be supplied in range of high alloy materials such as Titanium,
Hastelloy and SMO. MV has the retainer ring system which makes it
possible to supply it with many types of seat materials, thus optimizing
it to specic process conditions. The retainer ring can also be replaced
with a V-port for control duties.
MV
MV
MV
MV
RKO
Isolation valve before and/or after
XV
DN 50 - DN 1000
This compact bi-directional (double seated) valve resists high differential
pressures. It comes in stainless steel and either as semi lugged or as full
lugged. It has the TwinPackTM and the retainer ring system as standard.
Reduced cavities gives good ow characteristics.
Isolation pump between pump and tower where
bi-directional sealing is required.
XV
XV
XV
XV
XV
RKO
Titanium valve
Inlet
Mixer/Pump
On-Off valve at mixer/pump, manufactured in
Titanium or Hastelloy C depending on media.
D2G
DN 100 - DN 700
For contaminated pulp or reject handling which requires full bore and extremly fast manouvring, this D2G valve is an excellent choice. The valve
is designed of a two piece valve body in stainless steel with unique sliding faces positioned between the gate and housing halves in order to
minimize friction. D2G is equipped with two hard chromed gates working
towards each other in the bore for fast opening/closure.
Return to pulper
D2G
Rapid closing valve on return to pulper.
Primary
screening
Inlet
D2G
Accept
Reject
RKO
DN 100 - DN 700
The RKO valve is reliable and particularly well suited for really demanding
reject and other abrasive waste. The valve has a circular inlet and a
square outlet and the gate has a rectangular shape and a bevel edge.
This special shut-off design prevent it from clogging, which often is a
problem in combination with junk traps, coarse reject and cleaners.
RKO comes in a robust two piece valve body in cast iron or stainless
steel with integrated purge ports. As standard it is supplied with a hard
chromed gate in Duplex stainless steel, exchangeable guide strips,
TwinPackTM and the retainer ring system. For the toughest process
conditions, the valve can also be supplied with double gland for optimal
operating performance. If needed, the valve can be supplied with an
adaptor cone on the square side for welding connection or for connection
to a circular ange.
Accept
Return to pulper
D2G
Inlet
Primary
Inlet
screening
Reject
Reject
RKO
RKO
Accept
As upper and lower valve on coarse reject.
JT
DN 100 - DN150/DN 250
As a complete Junk Trap, the JT is an excellent choice. It consist of a
standard RKO on the inlet side and specially designed valve called JTV
on the outlet side. In between the valves is a specially designed reject
tank installed. The tank has ush connections for water or air and sight
glasses for inspection. All parts are designed and optimized for the most
extreme process conditions.
Stafsj 2011-05-06
JOHANNESBURG
: 011 397-2833
Tel
: 011 397-4700
Fax
E-mail : sales.jhb@valve.co.za
TECHNICAL SALES & SUPPORT
Richards Bay : 083 320-0393
Rustenburg : 083 227-7722
Sasolburg
: 083 321-4960
Secunda
: 083 656-4254 /
082 495 3751
DURBAN
Tel
: 031 579-2593
Fax
: 031 579-2562
E-mail : sales@valve.co.za
www.valve.co.za