Professional Documents
Culture Documents
Product Description
MCI-2027 is a single component, 90% solids, UV-stable,
VOC Compliant, Aliphatic Polyurea that was developed
for high gloss floor topcoats, chemical resistance,
and corrosion control. This coating provides reliable
performance in a wide range of temperatures and
climate conditions. MCI-2027 has excellent resistance
to UV rays, abrasion, and many of todays harshest
chemicals.
ADVANTAGES
Displays excellent adhesion characteristics to a variety
of substrates / coatings.
Unlimited pot life increases the workability of the
coating, providing consistent aggregate broadcasts and
uniform topcoat applications.
Will provide a glossy smooth finish when cured.
Coating displays excellent chemical and abrasion
resistance.
Emits virtually no odors and can be applied indoors
with minimal disturbance to surrounding activities.
VOC FREE
100% UV-Stable Aliphatic Chemistry
Versatile, crystal clear topcoat for use on both
horizontal and vertical applications.
Can be used for immersion and non-immersion
service.
Single component means no possible mixing errors,
thus eliminating the human error factor.
Extended cure time delivers great self-leveling
properties and glass-smooth finishes.
Primary Applications
Heavy traffic areas
Aircraft hangar floors
Maintenance facilities
Offshore platforms
Industrial shop floors
Commercial kitchens
Bathrooms and Lavatories
Chemical manufacturing plants
Wastewater treatment applications
Bar, table, and countertop sealer
TEST
RESULT
Tensil Strength
ASTM D412
5500
Compressive Strength
(psi Mpa)
ASTM D695
Elongation
ASTM D412
75
Tear Strength
ASTM 2240
800
Hardness Shore D
ASTM 2240
80
ASTM D1737
Pass
ASTM D968
30
Abrasion Resistance
CS-17 Wheel gm Load
ASTM D4060
Gloss
ASTM D523
+91
12000
coverage
Recommended Coverage
Topcoat Over Full Chip 150-250 sf/gal @8.0 mils
DFT (3.69 - 6.15 m2/L @200 mic)
Topcoat Over Solid Color 400-700 sf/gal @3.2 mils
DFT (9.83 - 17.20 m2/L @80 mic)
Topcoat Over Quartz 125-200 sf/gal @8.3 mils DFT
(3.07 - 4.92 m2/L @207.5 mic)
VOC compliant in all 50 states and Canada
Single Component
72F (24C)
Tack Free-1-2 hrs
Relativity Humidity
54% Hard dry-3-6 hrs
Recoat Minimum -
4 hours
Recoat Maximum 1
2 hours
Coverage:
1,600 square feet, per gallon, per mil.
(39.3 m2/L @25 mic)
Adhesion Results with performance data
ASTM D-4541 Elcometer
Concrete-no primer concrete failure >500psi
Concrete-primer concrete failure >550psi
Steel- primer shear failure >2000psi
Chemical Resistance with performance
data
Acetic Acid 100%
RC
Acetone
R
Ammonium Hydroxide 50%
RC
Benzene
RC
Brake Fluid
Brine saturated H2O
Chlorinated H2O
Diesel fuel
Ethanol
Gasoline
Gasoline/5% MTBE
Gasoline/5% Methanol
Hydrochloric Acid 20%
Hydrofluoric Acid 10%
Hydraulic fluid (oil)
Isopropyl Alcohol
Jet Fuel (JP-4)
Lactic Acid
MEK
Methanol
Methylene Chloride
Mineral Spirits
Motor Oil
MTBE
Muriatic Acid 10%
NaCl/H2O 10%
Nitric Acid 20%
Phosphoric Acid 10%
Phosphoric Acid 50%
Potassium Hydroxide 10%
Potassium Hydroxide 20%
Propylene Carbonate
Skydrol
Sodium Hydroxide 25%
Sodium Hydroxide 50%
Sodium Hypchlorite 10%
Sodium Bicarbonate
Stearic Acid
Sugar/H20
Sulfuric Acid 10%
Sulfuric Acid >50%
Toluene
1, 1,1-Trichlorethane
Trisodium Phosphate
Vinegar/H2O 5%
H2O 14 days at 82
Xylene
R
R
R
R
R
R
R
R
R
RC
R
R
R
RC
R
R
C
R
R
C
R
R
RC
R
NR
R
R, Dis
RC
RC
R
R. Dis
R
R
R
R
R
R
R
C
R
R
CR
R
LIMITED WARRANTY
All statements, technical information and recommendations contained herein are based on tests Cortec Corporation
believes to be reliable, but the accuracy or completeness thereof is not guaranteed.
Cortec Corporation warrants Cortec products will be free from defects when shipped to customer. Cortec Corporations obligation under this warranty shall be limited to replacement of product that proves to be defective.
To obtain replacement product under this warranty, the customer must notify Cortec Corporation of the claimed
defect within six months after shipment of product to customer. All freight charges for replacement products shall
be paid by customer.
Cortec Corporation shall have no liability for any injury, loss or damage arising out of the use of or the inability
to use the products.
BEFORE USING, USER SHALL DETERMINE THE SUITABILITY OF THE PRODUCT FOR ITS INTENDED
USE, AND USER ASSUMES ALL RISK AND LIABILITY WHATSOEVER IN CONNECTION THEREWITH. No
representation or recommendation not contained herein shall have any force or effect unless in a written document
signed by an officer of Cortec Corporation.
THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, EXPRESS, IMPLIED
OR STATUTORY, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
OF FITNESS FOR A PARTICULAR PURPOSE. IN NO CASE SHALL CORTEC CORPORATION BE LIABLE
FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Distributed by:
Revised 10/3/12. Cortec Corporation 2006-2012. All rights reserved. Supersedes: 2/23/12.
MCI is a registered trademark of Cortec Corporation. 2012, Cortec Corporation. All Rights Reserved.
Copying of these materials in any form without the written authorization of Cortec Corporation is strictly prohibited.
ISO accreditation applies to Cortecs processes only